Search

Millions of people worldwide suffer from musculoskeletal damage, thus using the largest proportion of rehabilitation services. The limited self-regenerative capacity of bone and cartilage tissues necessitates the development of functional biomaterials. Magnetoactive materials are a promising solution due to clinical safety and deep tissue penetration of magnetic fields (MFs) without attenuation and tissue heating. Herein, electrospun microfibrous scaffolds were developed based on piezoelectric poly(3-hydroxybutyrate) (PHB) and composite magnetic nanofillers [magnetite with graphene oxide (GO) or reduced GO]. The scaffolds' morphology, structure, mechanical properties, surface potential, and piezoelectric response were systematically investigated. Furthermore, a complex mechanism of enzymatic biodegradation of these scaffolds is proposed that involves (i) a release of polymer crystallites, (ii) crystallization of the amorphous phase, and (iii) dissolution of the amorphous phase. Incorporation of Fe 3 O 4 , Fe 3 O 4 -GO, or Fe 3 O 4 -rGO accelerated the biodegradation of PHB scaffolds owing to pores on the surface of composite fibers and the enlarged content of polymer amorphous phase in the composite scaffolds. Six-month biodegradation caused a reduction in surface potential (1.5-fold) and in a vertical piezoresponse (3.5-fold) of the Fe 3 O 4 -GO scaffold because of a decrease in the PHB β-phase content. In vitro assays in the absence of an MF showed a significantly more pronounced mesenchymal stem cell proliferation on composite magnetic scaffolds compared to the neat scaffold, whereas in an MF (68 mT, 0.67 Hz), cell proliferation was not statistically significantly different when all the studied scaffolds were compared. The PHB/Fe 3 O 4 -GO scaffold was implanted into femur bone defects in rats, resulting in successful bone repair after nonperiodic magnetic stimulation (200 mT, 0.04 Hz) owing to a synergetic influence of increased surface roughness, the presence of hydrophilic groups near the surface, and magnetoelectric and magnetomechanical effects of the material.

In this investigation, the electrospun nanocomposite scaffolds were developed utilizing poly-3-hydroxybutyrate (PHB), zein, and multiwalled carbon nanotubes (MWCNTs) at varying concentrations of MWCNTs including 0.5 and 1 wt%. Based on the SEM evaluations, the scaffold containing 1 wt% MWCNTs (PZ-1C) exhibited the lowest fiber diameter (384 ± 99 nm) alongside a suitable porosity percentage. The presence of zein and MWCNT in the chemical structure of the scaffold was evaluated by FTIR. Furthermore, TEM images revealed the alignment of MWCNTs with the fibers. Adding 1 % MWCNTs to the PHB-zein scaffold significantly enhanced tensile strength by about 69 % and reduced elongation by about 31 %. Hydrophilicity, surface roughness, crystallinity, and biomineralization were increased by incorporating 1 wt% MWCNTs, while weight loss after in vitro degradation was decreased. The MG-63 cells exhibited enhanced attachment, viability, ALP secretion, calcium deposition, and gene expression (COLI, RUNX2, and OCN) when cultivated on the scaffold containing MWCNTs compared to the scaffolds lacking MWCNTs. Moreover, the study found that MWCNTs significantly reduced platelet adhesion and hemolysis rates below 4 %, indicating their favorable anti-hemolysis properties. Regarding the aforementioned results, the PZ-1C electrospun composite scaffold is a promising scaffold with osteogenic properties for bone tissue engineering applications., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Recent research focuses on fabricating scaffolds imitating the extracellular matrix (ECM) in texture, composition, and functionality. Moreover, specific nano-bio-particles can enhance cell differentiation. Decellularized ECM nanoparticles possess all of the mentioned properties. In this research, cartilage ECM, extracted from the cow's femur condyle, was decellularized, and ECM nanoparticles were synthesized. Finally, nanocomposite electrospun fibers containing polyhydroxybutyrate (PHB), chitosan (Cs) nanoparticles, and ECM nanoparticles were fabricated and characterized. TEM and DLS results revealed ECM nanoparticle sizes of 17.51 and 21.6 nm, respectively. Optimal performance was observed in the scaffold with 0.75 wt% ECM nanoparticles (PHB-Cs/0.75E). By adding 0.75 wt% ECM, the ultimate tensile strength and elongation at break increased by about 29 % and 21 %, respectively, while the water contact angle and crystallinity decreased by about 36° and 2 %, respectively. Uneven and rougher surfaces of the PHB-Cs/0.75E were determined by FESEM and AFM images, respectively. TEM images verified the uniform dispersion of nanoparticles within the fibers. After 70 days of degradation in PBS, the PHB-Cs/0.75E and PHB-Cs scaffolds demonstrated insignificant weight loss differences. Eventually, enhanced viability, attachment, and proliferation of the human costal chondrocytes on the PHB-Cs/0.75E scaffold, concluded from MTT, SEM, and DAPI staining, confirmed its potential for cartilage tissue engineering., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

This is the first comprehensive study of the impact of biodegradation on the structure, surface potential, mechanical and piezoelectric properties of poly(3-hydroxybutyrate) (PHB) scaffolds supplemented with reduced graphene oxide (rGO) as well as cell behavior under static and dynamic mechanical conditions. There is no effect of the rGO addition up to 1.0 wt% on the rate of enzymatic biodegradation of PHB scaffolds for 30 d. The biodegradation of scaffolds leads to the depolymerization of the amorphous phase, resulting in an increase in the degree of crystallinity. Because of more regular dipole order in the crystalline phase, surface potential of all fibers increases after the biodegradation, with a maximum (361 ± 5 mV) after the addition of 1 wt% rGO into PHB as compared to pristine PHB fibers. By contrast, PHB-0.7rGO fibers manifest the strongest effective vertical (0.59 ± 0.03 pm V -1 ) and lateral (1.06 ± 0.02 pm V -1 ) piezoresponse owing to a greater presence of electroactive β-phase. In vitro assays involving primary human fibroblasts reveal equal biocompatibility and faster cell proliferation on PHB-0.7rGO scaffolds compared to pure PHB and nonpiezoelectric polycaprolactone scaffolds. Thus, the developed biodegradable PHB-rGO scaffolds with enhanced piezoresponse are promising for tissue-engineering applications., (© 2023 Wiley-VCH GmbH.)

In this work we investigated tenogenic differentiation of adipose-derived mesenchymal stem cells (AdMSCs), which were seeded onto silk fibroin/poly-3-hydroxybutyrate (SF/P3HB) scaffolds with aligned topography, and high mechanical strength. The electrospinning process was optimized by using the response surface method (RSM) and SF/P3HB nanofibrous matrices with a total polymer concentration of 5% (SF: PHB = 3: 1), flow rate 1 mL/h, collector rotation speed 2000 rpm, applied voltage 14 kV, and collector distance 25 cm were obtained. The average fiber diameter was 699 ± 203 nm and 80% of the nanofibers were aligned within the ±15 o range. SF reinforcement reduced the crystallinity of P3HB, and the elastic modulus was found to be 197.0 ± 7.7 MPa. The scaffolds showed bacteriostatic effect. A 21-day of cell culture study was performed with rat rAdMSCs in the absence and presence of tenogenic differentiation factor-5 (GDF-5). The results demonstrated that SF/P3HB scaffolds allow the cells to proliferate and differentiate to the tenocytes. However, no significant effect of GDF-5 on the differentiation of cells was observed. These findings indicated that our aligned SF/P3HB scaffolds have a significant potential to be used for tendon tissue engineering., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Efficient design for bone tissue engineering requires an understanding of the appropriate selection of biomimetic natural or synthetic materials and scalable fabrication technologies. In this research, poly (3-hydroxybutyrate) (PHB) and starch (5-15 wt%) as biological macromolecules were used to fabricate novel biomimetic scaffolds by electrospinning method. SEM results of electrospun scaffolds revealed bead-free nanofibers and three-dimensional homogenous structures with highly interconnected pores. Results of FTIR and Raman demonstrated that there were hydrogen bonds between the two polymers. The tensile strength of scaffolds was significantly improved by adding starch up to 10 wt%, from 3.05 to 15.54 MPa. In vitro degradation and hydrophilicity of the scaffolds were improved with the presence of starch. The viability and proliferation of MG-63 cells and alkaline phosphatase (ALP) activity were remarkably increased in the PHB-starch scaffolds compared to the PHB and control samples. The mineralization and calcium deposition of MG-63 cells were confirmed by alizarin red staining. It is concluded that PHB/starch electrospun scaffold could be a good candidate for bone tissue engineering applications., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Bioresorbable biomaterials can fill bone defects and act as temporary scaffold to recruit MSCs to stimulate their differentiation. Among the different bioresorbable polymers studied, this work focuses on poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) and poly(ε-caprolactone) (PCL). Were prepared blends of PHBV and PCL to obtain PHBV based biomaterials with good tenacity, important for bone tissue repair, associated with biocompatible properties of PCL. This study assesses the viability of Vero cells on scaffolds of PHBV, PCL, and their blends and the osteogenic differentiation of mesenchymal stem cells (MSCs). Materials were characterized in surface morphology, DSC and Impact Strength (IS). Vero cells and MSCs were assessed by MTT assay, cytochemical and SEM analysis. MSC osteogenic differentiation was evaluated through alizarin red staining and ALP activity. We found some roughness onto surface materials. DSC showed that the blends presented two distinct melting peaks, characteristic of immiscible blends. IS test confirmed that PHBV-PCL blends is an alternative for increase the tenacity of PHBV. MTT assay showed cells with high metabolic activities on extract toxicity test, but with low activity in the direct contact test. SEM analysis showed spreading cells with irregular and flattened morphology on different substrates. Cytochemical study revealed that MSCs maintained their morphology, although in smaller number for MSCs. The development of nodules of mineralized organic matrix in MSC cultures was identified by alizarin red staining and osteogenic differentiation was confirmed by the quantification of ALP activity. Thus, our scaffolds did not interfere on viability of Vero cells or the osteogenic differentiation of MSCs., (© 2021. The Author(s).)

Tissue engineering scaffolds with nanofibrous structures provide positive support for cell proliferation and differentiation in biomedical fields. These scaffolds are widely used for defective tissue repair and drug delivery. However, the degradation performance and mechanical properties of scaffolds are often unsatisfactory. Here, we successfully prepared a novel poly(3-hydroxybutyrate-4-hydroxybutyrate)/polypyrrole (P34HB-PPy) core-shell nanofiber structure scaffold with electrospinning and in situ surface polymerization technology. The obtained composite scaffold showed good mechanical properties, hydrophilicity, and thermal stability based on the universal material testing machine, contact angle measuring system, thermogravimetric analyzer, and other methods. The results of the in vitro bone marrow-derived mesenchymal stem cells (BMSCs) culture showed that the P34HB-PPy composite scaffold effectively mimicked the extracellular matrix (ECM) and exhibited good cell retention and proliferative capacity. More importantly, P34HB is a controllable degradable polyester material, and its degradation product 3-hydroxybutyric acid (3-HB) is an energy metabolite that can promote cell growth and proliferation. These results strongly support the application potential of P34HB-PPy composite scaffolds in biomedical fields, such as tissue engineering and soft tissue repair., Competing Interests: The authors declare that they have no conflicts of interest., (Copyright © 2021 Wentai Guo et al.)

As a member of the polyhydroxyalkanoate (PHAs) family, Poly(3-hydroxybutyrate) (PHB) has attracted much attention for a variety of medical applications because of its desirable properties such as high biocompatibility, nontoxic degradation products and high mechanical strength in comparison to other polymers in different fields including tissue engineering. There are different approaches such as making PHB alloy scaffolds, using PHB as a coating for ceramic-based scaffolds and producing composite scaffolds by using a mixture of PHB with ceramic particles utilized to improve hydrophobicity, degradation rate and brittleness. In this review, different applications of PHB, its alloys and composites in tissue engineering are explained based on the common methods of fabrication such as polymeric sponge replication, electrospinning and salt leaching., (Copyright © 2020 Elsevier B.V. All rights reserved.)

The biocompatibility and neuron regenerating properties of various bioactive glass (BG)/polyhydroxyalkanoate (PHA) blend composites were assessed in order to study their suitability for peripheral nerve tissue applications, specifically as lumen structures for nerve guidance conduits. BG/PHA blend composites were fabricated using Bioactive glass® 45 S5 (BG1) and BG 1393 (BG2) with the 25:75 poly(3-hydroxyoctanoate/poly3-hydroxybutyrate), 25:75 P(3HO)/P(3HB) blend (PHA blend). Various concentrations of each BG (0.5 wt%, 1.0 wt% and 2.5 wt%) were used to determine the effect of BG on neuronal growth and differentiation, in single culture using NG108-15 neuronal cells and in a co-culture along with RN22 Schwann cells. NG108-15 cells exhibited good growth and differentiation on all the PHA blend composites showing that both BGs have good biocompatibility at 0.5 wt%, 1.0 wt% and 2.5 wt% within the PHA blend. The Young's modulus values displayed by all the PHA blend/BG composites ranged from 385.6 MPa to 1792.6 MPa, which are able to provide the required support and protective effect for the regeneration of peripheral nerves. More specifically, the tensile strength obtained in the PHA blend/BG1 (1.0 wt%) (10.0 ± 0.6 MPa) was found to be similar to that of the rabbit peroneal nerve. This composite also exhibited the best biological performance in supporting growth and neuronal differentiation among all the substrates. The neurite extension on this composite was found to be remarkable with the neurites forming a complex connection network.

Chondral defects are challenging to repair because of the poor self-healing capacity of articular cartilage. The aim of this study was to compare and investigate the cartilage regeneration of stromal vascular fraction (SVF) cells and adipose-derived stem cells (ASCs) co-cultured with chondrocytes seeding on scaffolds composed of polyhydroxybutyrate (PHB)/poly-(hydroxybutyrate-co-hydroxyhexanoate) (PHBHHx). In this study, the cellular morphologies and proliferation capabilities on scaffolds were evaluated. Next, scaffolds with 1:1 co-culture of ASCs/SVF and chondrocytes were implanted into the full-thickness cartilage defects in rabbit knee for 10 weeks. Cells seeded on the scaffolds showed better adhesion, migration, and proliferation in vitro. Importantly, implantation with scaffolds with SVF and chondrocytes revealed more desirable in vivo healing outcomes. Our results illustrate a one-step surgical procedure for the regeneration of focal cartilage defects using a mixture of SVF from adipose tissue and uncultured chondrocytes.

In this study bioactive and bioresorbable porous scaffolds for bone tissue regeneration, based on poly(3-hydroxybutyrate) (PHB), are presented. The porous structure is obtained by thermally induced phase separation (TIPS) technique, whereas the osteoinductivity and osteoconductivity are enhanced through the incorporation of hydroxyapatite (HA). The HA particles are generated in PHB using an innovative filler in situ synthesis, and the properties of the composite scaffolds are then compared to scaffolds obtained by conventional mechanical dispersion of ex situ synthesized HA particles. The in situ synthesis leads to composite materials with improved porosity, even at high filler content, without any degradation of the polymeric matrix as confirmed by GPC and DSC measurements. On the contrary, the samples prepared by ex situ method show a suppressed porosity by increasing the inorganic filler content, therefore limiting the amount of HA that can be loaded in PHB and the resulting bioactivity. The possibility to use PHB/HA porous composites as scaffolds for bone tissue regeneration, is assessed by preliminary cell viability in vitro studies. In particular, it is observed that the composites are fully cytocompatible and able to sustain MC3T3-E1 mouse pre-osteoblast cells adhesion and proliferation. Investigations on cell morphology reveal, for all PHB/HA scaffolds, the presence of differentiated cells with a predominance of osteocyte-like morphology, which are not observed for neat PHB scaffolds. Moreover, the MC3T3-E1 cells differentiation towards osteoblastic phenotype is further supported by the evaluation of the early osteogenic markers. In particular, samples loaded with HA in situ synthesized showed the highest ALP production and typical morphology of the terminal differentiation stages of osteoblasts., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Objective: Bone tissue engineering was introduced in 1995 and provides a new way to reconstruct bone and repair bone defects. However, the design and fabrication of suitable bionic bone scaffolds are still challenging, and the ideal scaffolds in bone tissue engineering should have a three-dimensional porous network, good biocompatibility, excellent biodegradability and so on. The purpose of our research was to investigate whether a bioplasticpoly3-hydroxybutyrate4-hydroxybutyrate (P34HB) electrospun fibre scaffold is conducive to the repair of bone defects, and whether it is a potential scaffold for bone tissue engineering., Materials and Methods: The P34HB electrospun fibre scaffolds were prepared by electrospinning technology, and the surface morphology, hydrophilicity, mechanical properties and cytological behaviour of the scaffolds were tested. Furthermore, a calvarial defect model was created in rats, and through layer-by-layer paper-stacking technology, the P34HB electrospun fibre scaffolds were implanted into the calvarial defect area and their effect on bone repair was evaluated., Results: The results showed that the P34HB electrospun fibre scaffolds are interwoven with several fibres and have good porosity, physical properties and chemical properties and can promote cell adhesion and proliferation with no cytotoxicity in vitro. In addition, the P34HB electrospun fibre scaffolds can promote the repair of calvarial defects in vivo., Conclusions: These results demonstrated that the P34HB electrospun fibre scaffold has a three-dimensional porous network with good biocompatibility, excellent biosafety and ability for bone regeneration and repair; thus, the P34HB electrospun fibre scaffold is a potential scaffold for bone tissue engineering., (© 2019 The Authors. Cell Proliferation Published by John Wiley & Sons Ltd.© 2019 The Authors. Cell Proliferation Published by John Wiley & Sons Ltd.)

Polyhydroxyalkanoates (PHA) are natural polyesters produced by microorganisms under carbon source excess and limiting nutrient conditions. However, these biopolymers possess low mechanical and thermal properties, decreasing their potential applications in the medical field. Electrospinning is a technique that forms fibers from different polymers. PHA electrospun fibers improve the mechanical properties and decrease the crystallinity of PHA, including poly-3-hydroxybutyrate and its copolymers, which is attributed to the metastable structure (β-form) formation. Therefore, the mechanical properties of fibers are intrinsically related to their plane orientation. Aligned fibers present better mechanical properties than randomly oriented fibers. However, randomly oriented fibers promote cell-fiber interaction and cell infiltration. Fibers produced with PHA blended with other polymers have shown improved mechanical and biological properties. Gelatin, zein and cellulose acetate are the main natural polymers that have been blended with PHA for electrospun scaffolds. For scaffold production by coaxial electrospinning, gelatin has been used as a shell and PHA as the core. PHA have been combined with different synthetic polymers and plasticizers resulting in an increase in the PHA miscibility. Therefore, the use of electrospinning in the development of PHA-based scaffolds seems to be an attractive method to change the intrinsic polymer features, increasing and enhancing PHA applications in tissue engineering., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Electrospun polyhydroxybutyrate (PHB)/carboxyl multi-walled carbon nanotubes grafted polyhydroxybutyrate (CMWCNT-g-PHB) composite nanofibers scaffolds were fabricated by electrospinning technology. The grafted product CMWCNT-g-PHB was prepared by condensation reactions between the carboxyl groups of CMWCNT and hydroxyl groups of PHB molecules and characterized by FTIR, XRD, XPS, TG and TEM measurements. The surface morphology, hydrophilicity and tensile mechanical properties of the electrospun PHB/CMWCNT-g-PHB composite nanofibers membrane scaffolds were investigated. The values of tensile strength, breaking elongation rate, initial modulus and fracture energy of the composite nanofibers scaffolds can reach to 4.64MPa, 255.59%, 88MPa and 109.73kJ/m 2 , respectively. The biodegradability and cytocompatibility of the electrospun composite nanofibers scaffolds were preliminarily evaluated. The as-prepared electrospun PHB/CMWCNT-g-PHB composite nanofibers scaffolds with the characteristics of large specific area, high porosity, good biodegradability and cytocompatibility as well as sufficient mechanical properties should be more promising in the field of tissue engineering scaffolds and biological medicine., (Copyright © 2017 Elsevier B.V. All rights reserved.)

In response to the demand for new implant materials characterized by high biocompatibility and bioresorption, two prototypes of fibrous nanocomposite implants for osseous tissue regeneration made of a newly developed blend of poly(l-lactide- co -glycolide) (PLGA) and syntheticpoly([ R,S ]-3-hydroxybutyrate), PLGA/PHB, have been developed and fabricated. Afibre-forming copolymer of glycolide and l-lactide (PLGA) was obtained by a unique method of synthesis carried out in blocksusing Zr(AcAc)₄ as an initiator. The prototypes of the implants are composed of three layers of PLGA or PLGA/PHB, nonwoven fabrics with a pore structure designed to provide the best conditions for the cell proliferation. The bioactivity of the proposed implants has been imparted by introducing a hydroxyapatite material and IGF1, a growth factor. The developed prototypes of implants have been subjected to a set of in vitro and in vivobiocompatibility tests: in vitro cytotoxic effect, in vitro genotoxicity and systemic toxicity. Rabbitsshowed no signs of negative reactionafter implantation of the experimental implant prototypes., Competing Interests: The authors declare no conflict of interest.

Exploring the importance of nanofibrous scaffold with traditionally important medicine as a wound dressing material prevents infection and aids in faster healing of wounds. In the present study, the Collagen (COL) from the marine fish skin was extracted and employed for coating the Poly(3-hydroxybutyric acid) (P)-Gelatin (G) nanofibrous scaffold with a bioactive Coccinia grandis extract (CPE) fabricated through electrospinning. Further, the fabricated collagen coated nanofibrous scaffold (PG-CPE-COL) applied to the experimental wound of rats and the wound healing was analyzed with by physiochemical and biological techniques. The increased level of hydroxyproline, hexosamine and uronic acid was observed in PG-CPE-COL treated than the other groups. The CPE and collagen in the nanofibrous scaffold accelerates the wound healing and thereby reduced the inflammation caused by the cyclooxygenase-2 (COX-2) and inducible nitric oxide synthases (iNOS) in wound healing. The nanofibrous scaffold has influenced the expression of various growth factors such as vascular endothelial growth factor (VEGF), epidermal growth factor (EGF) and transforming growth factor (TGF-β). In addition, the PG-CPE-COL nanofibrous scaffold increases the deposition of collagen synthesis and accelerates reepithelialization. Thus, the results suggest that the collagen coated nanofibrous scaffold with bioactive traditional medicine enhanced the faster healing of wound., (Copyright © 2017 Elsevier B.V. All rights reserved.)

Electrospinning is an effective means to generate nano- to micro-scale polymer fibers resembling native extracellular matrix for tissue engineering. However, a major problem of electrospun materials is that limited pore size and porosity may prevent adequate cellular infiltration and tissue ingrowth. In this study, we first prepared thin layers of hydroxyapatite nanoparticle (nHA)/poly-hydroxybutyrate (PHB) via electrospinning. We then laminated the nHA/PHB thin layers to obtain a scaffold for cell seeding and bone tissue engineering. The results demonstrated that the laminated scaffold possessed optimized cell-loading capacity. Bone marrow mesenchymal stem cells (MSCs) exhibited better adherence, proliferation and osteogenic phenotypes on nHA/PHB scaffolds than on PHB scaffolds. Thereafter, we seeded MSCs onto nHA/PHB scaffolds to fabricate bone grafts. Histological observation showed osteoid tissue formation throughout the scaffold, with most of the scaffold absorbed in the specimens 2months after implantation, and blood vessels ingrowth into the graft could be observed in the graft. We concluded that electrospun and laminated nanoscaled biocomposite scaffolds hold great therapeutic potential for bone regeneration., (Copyright © 2016 Elsevier B.V. All rights reserved.)

Polyhydroxyalkanoate (PHA) is a microbial polymer that has been at the forefront of many attempts at tissue engineering. However, the surface of poly(3-hydroxybutyrate-co-4-hydroxybutyrate) (P(3HB-co-4HB)) is hydrophobic with few recognition sites for cell attachment. Various concentrations of fish-scale collagen peptides (FSCPs) were incorporated into P(3HB-co-4HB) copolymer by aminolysis. Later, FSCPs were introduced onto the aminolyzed P(3HB-co-4HB) scaffolds. Introduction of the FSCP groups was verified using Fourier transform infrared spectroscopy and the ninhydrin method. The effect of the incorporation of FSCPs on hydrophilicity was investigated using the water contact angle. As the concentration of FSCPs increased, the water contact angle decreased. In vitro study demonstrated that P(3HB-co-4HB)/FSCP scaffolds provided better cell attachment and growth of L929 mouse fibroblast cells and better cell proliferation. In vivo study showed that P(3HB-co-4HB)/1.5 wt% FSCPs had a significant effect on wound contractions, with the highest percentage of wound closure (61%) in 7 d.

The osteogenic potential of human adipose-derived stem cells (HADSCs) co-cultured with human osteoblasts (HOBs) using selected HADSCs/HOBs ratios of 1:1, 2:1, and 1:2, respectively, is evaluated. The HADSCs/HOBs were seeded on electrospun three-dimensional poly[(R)-3-hydroxybutyric acid] (PHB) blended with bovine-derived hydroxyapatite (BHA). Monocultures of HADSCs and HOBs were used as control groups. The effects of PHB-BHA scaffold on cell proliferation and cell morphology were assessed by AlamarBlue assay and field emission scanning electron microscopy. Cell differentiation, cell mineralization, and osteogenic-related gene expression of co-culture HADSCs/HOBs were examined by alkaline phosphatase (ALP) assay, alizarin Red S assay, and quantitative real time PCR, respectively. The results showed that co-culture of HADSCs/HOBs, 1:1 grown into PHB-BHA promoted better cell adhesion, displayed a significant higher cell proliferation, higher production of ALP, extracellular mineralization and osteogenic-related gene expression of run-related transcription factor, bone sialoprotein, osteopontin, and osteocalcin compared to other co-culture groups. This result also suggests that the use of electrospun PHB-BHA in a co-culture HADSCs/HOBs system may serve as promising approach to facilitate osteogenic differentiation activity of HADSCs through direct cell-to-cell contact with HOBs., (© 2015 Wiley Periodicals, Inc.)

Poly(hydroxybutyrate) (PHB)/cellulose acetate (CA) blend nanofiber scaffolds were fabricated by electrospinning using the blends of chloroform and DMF as solvent. The blend nanofiber scaffolds were characterized by SEM, FTIR, XRD, DSC, contact angle and tensile test. The blend nanofibers exhibited cylindrical, uniform, bead-free and random orientation with the diameter ranged from 80-680 nm. The scaffolds had very well interconnected porous fibrous network structure and large aspect surface areas. It was found that the presence of CA affected the crystallization of PHB due to formation of intermolecular hydrogen bonds, which restricted the preferential orientation of PHB molecules. The DSC result showed that the PHB and CA were miscible in the blend nanofiber. An increase in the glass transition temperature was observed with increasing CA content. Additionally, the mechanical properties of blend nanofiber scaffolds were largely influenced by the weight ratio of PHB/CA. The tensile strength, yield strength and elongation at break of the blend nanofiber scaffolds increased from 3.3 ± 0.35 MPa, 2.8 ± 0.26 MPa, and 8 ± 0.77% to 5.05 ± 0.52 MPa, 4.6 ± 0.82 MPa, and 17.6 ± 1.24% by increasing PHB content from 60% to 90%, respectively. The water contact angle of blend nanofiber scaffolds decreased about 50% from 112 ± 2.1° to 60 ± 0.75°. The biodegradability was evaluated by in vitro degradation test and the results revealed that the blend nanofiber scaffolds showed much higher degradation rates than the neat PHB. The cytocompatibility of the blend nanofiber scaffolds was preliminarily evaluated by cell adhesion studies. The cells incubated with PHB/CA blend nanofiber scaffold for 48 h were capable of forming cell adhesion and proliferation. It showed much better biocompatibility than pure PHB film. Thus, the prepared PHB/CA blend nanofiber scaffolds are bioactive and may be more suitable for cell proliferation suggesting that these scaffolds can be used for wound dressing or tissue-engineering scaffolds., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Tissue-engineered heart valves (TEHVs), based on polyglycolic acid (PGA) scaffolds coated with poly-4-hydroxybutyrate (P4HB), have shown promising in vivo results in terms of tissue formation. However, a major drawback of these TEHVs is compaction and retraction of the leaflets, causing regurgitation. To overcome this problem, the aim of this study was to investigate: (a) the use of the slowly degrading poly-ε-caprolactone (PCL) scaffold for prolonged mechanical integrity; and (b) the use of lower passage cells for enhanced tissue formation. Passage 3, 5 and 7 (P3, P5 and P7) human and ovine vascular-derived cells were seeded onto both PGA-P4HB and PCL scaffold strips. After 4 weeks of culture, compaction, tissue formation, mechanical properties and cell phenotypes were compared. TEHVs were cultured to observe retraction of the leaflets in the native-like geometry. After culture, tissues based on PGA-P4HB scaffold showed 50-60% compaction, while PCL-based tissues showed compaction of 0-10%. Tissue formation, stiffness and strength were increased with decreasing passage number; however, this did not influence compaction. Ovine PCL-based tissues did render less strong tissues compared to PGA-P4HB-based tissues. No differences in cell phenotype between the scaffold materials, species or cell passage numbers were observed. This study shows that PCL scaffolds may serve as alternative scaffold materials for human TEHVs with minimal compaction and without compromising tissue composition and properties, while further optimization of ovine TEHVs is needed. Reducing cell expansion time will result in faster generation of TEHVs, providing more rapid treatment for patients., (Copyright © 2013 John Wiley & Sons, Ltd.)

We studied the possibility of long-term culturing of mouse mesenchymal stem cells on a porous scaffold made of biocompatible polymer poly-3-hydroxybutyrate. The cells remained viable for at least 2 months and passed more than 65 population doublings in culture. Culturing on the scaffold did not change surface phenotype of cells. 3D poly-3-hydroxybutyrate scaffolds are appropriate substrate for long-term culturing of mesenchymal stem cells.

A novel biodegradable nano/micro hybrid structure was obtained by electrospinning P3HB or PCL nanofibers onto a twisted silk fibroin (SF) structure, with the aim of fabricating a suitable scaffold for tendon and ligament tissue engineering. The electrospinning (ES) processing parameters for P3HB and PCL were optimized on 2D samples, and applied to produce two different nano/micro hybrid constructs (SF/ES-PCL and SF/ES-P3HB).Morphological, chemico-physical and mechanical properties of the novel hybrid scaffolds were evaluated by SEM, ATR FT-IR, DSC, tensile and thermodynamic mechanical tests. The results demonstrated that the nanofibers were tightly wrapped around the silk filaments, and the crystallinity of the SF twisted yarns was not influenced by the presence of the electrospun polymers. The slightly higher mechanical properties of the hybrid constructs confirmed an increase of internal forces due to the interaction between nano and micro components. Cell culture tests with L929 fibroblasts, in the presence of the sample eluates or in direct contact with the hybrid structures, showed no cytotoxic effects and a good level of cytocompatibility of the nano/micro hybrid structures in term of cell viability, particularly at day 1. Cell viability onto the nano/micro hybrid structures decreased from the first to the third day of culture when compared with the control culture plastic, but appeared to be higher when compared with the uncoated SF yarns. Although additional in vitro and in vivo tests are needed, the original fabrication method here described appears promising for scaffolds suitable for tendon and ligament tissue engineering.

Background: Alveolar cleft osteoplasty (ACO) using autologous bone grafts, is used worldwide as a standard treatment in the management of patients with clefts. Harvesting of the various autologous bone grafts is accompanied by considerable donor-site morbidity. Use of scaffold-based tissue engineering in ACO could potentially provide treatment options with decreased, or no donor-site morbidity. This study aims to demonstrate the technical and cell biological feasibility of using scaffold-based tissue engineering in ACO., Material and Methods: Pre-existing cone-beam computed tomography scans were used for 3D printing of custom-made scaffolds (tricalcium phosphate-polyhydroxybutyrate (TCP-PHB)) according to the individual geometry of the alveolar bone in patients with clefts. The scaffolds were seeded with commercially available human mesenchymal stem cells (hMSCs). Cell survival and cell proliferation was monitored by live-dead assay, scanning electron microscopy (SEM) and WST-1 assay. The osteogenic differentiation of hMSCs on the scaffolds was evaluated by alkaline phosphatase (ALP) assay., Results: The custom-made scaffolds were nearly identical to the size and shape of the digital master. Approximately 91% of the subsequently applied mesenchymal stem cells could be seeded on the rails. We could demonstrate successful cell proliferation by a factor of 5-7 over the first 3 weeks. SEM showed a pore-border growth of the hMSCs on the scaffolds after 3 weeks of cell proliferation. The successful osteogenic differentiation of the scaffold-seeded cells could be demonstrated., Conclusion: The concept of scaffold-based tissue engineering provides great potential as an alternative for the present gold standard of autologous bone grafts in ACO. The treatment causes less morbidity and is less invasive for managing young patients with cleft alveolar bone defects. Further in vivo studies and clinical trials are needed to demonstrate the advantages of this novel treatment for ACO in the clinical setting., (Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.)

Porous hydrogels have been explored for bone tissue engineering; however their poor mechanical properties make them less suitable as bone graft substitutes. Since incorporation of fillers is a well-accepted method for improving mechanical properties of hydrogels, in this work pullulan hydrogels were reinforced with nano-crystalline hydroxyapatite (nHAp) (5 wt% nHAp in hydrogel) and poly(3-hydroxybutyrate) (PHB) fibers (3 wt% fibers in hydrogel) containing nHAp (3 wt% nHAp in fibers). Addition of these fillers to pullulan hydrogel improved compressive modulus of the scaffold by 10 fold. However, the hydrophilicity of pullulan did not support adhesion and spreading of cells. To overcome this limitation, porous composite scaffolds were modified using a double diffusion method that enabled deposition of hydroxyapatite on pore walls. This method resulted in rapid and uniform coating of HAp throughout the three-dimensional scaffolds which not only rendered them osteoconductive in vitro but also led to an improvement in their compressive modulus. These results demonstrate the potential of mineralized pullulan-based composite scaffolds in non-load bearing bone tissue engineering., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

One of the major challenges facing researchers of tissue engineering is scaffold design with desirable physical and mechanical properties for growth and proliferation of cells and tissue formation. In this research, firstly, nano-bioglass powder with grain sizes of 55-56 nm was prepared by melting method of industrial raw materials at 1,400 °C. Then the porous ceramic scaffold of bioglass with 30, 40 and 50 wt% was prepared by using the polyurethane sponge replication method. The scaffolds were coated with poly-3-hydroxybutyrate (P3HB) for 30 s and 1 min in order to increase the scaffold's mechanical properties. XRD, XRF, SEM, FE-SEM and FT-IR were used for phase and component studies, morphology, particle size and determination of functional groups, respectively. XRD and XRF results showed that the type of the produced bioglass was 45S5. The results of XRD and FT-IR showed that the best temperature to produce bioglass scaffold was 600 °C, in which Na2Ca2Si3O9 crystal is obtained. By coating the scaffolds with P3HB, a composite scaffold with optimal porosity of 80-87% in 200-600 μm and compression strength of 0.1-0.53 MPa was obtained. According to the results of compressive strength and porosity tests, the best kind of scaffold was produced with 30 wt% of bioglass immersed for 1 min in P3HB. To evaluate the bioactivity of the scaffold, the SBF solution was used. The selected scaffold (30 wt% bioglass/6 wt% P3HB) was maintained for up to 4 weeks in this solution at an incubation temperature of 37 °C. The XRD, SEM EDXA and AAS tests were indicative of hydroxyapatite formation on the surface of bioactive scaffold. This scaffold has some potential to use in bone tissue engineering.

CO2 laser radiation was used to process poly(3-hydroxybutyrate) constructs - films and 3D pressed plates. Laser processing increased the biocompatibility of unperforated films treated with moderate uniform radiation, as estimated by the number and degree of adhesion of NIH 3T3 mouse fibroblast cells. The biocompatibility of perforated films modified in the pulsed mode did not change significantly. At the same time, pulsed laser processing of the 3D plates produced perforated scaffolds with improved mechanical properties and high biocompatibility with bone marrow-derived multipotent, mesenchymal stem cells, which show great promise for bone regeneration.

3D fine porous structures obtained by electrospinning a poly[(R,S)-3-hydroxybutyrate] (aPHB)/ poly[(R)-3-hydroxybutyrate] (PHB) (85/15 w/w) blend were successfully modified with human procollagen type I by simple immersion of the polyester scaffold in an aqueous solution of the protein. Effective modification of the scaffold with human procollagen I was confirmed by an immunodetection test, which revealed the presence of the procollagen type I as an outer layer even on inner structures of the porous matrixes. Biological tests of 3D fabrics made of the PHB blend provide support for the adhesion and proliferation of human fibroblasts, while their modification with procollagen type I increased the biocompatibility of the final scaffolds significantly, as shown by the notable increase in the number of attached cells during the early hours of their incubation. Based on these findings, human procollagen type I surface-modified aPHB/PHB scaffolds should be considered a promising material in regenerative medicine.

Objectives: Amongst the fourth generation of PHAs is bio-plasticpoly3-hydroxybutyrate4-hydroxybutyrate (P34HB); it is thus appropriate to perform novel research on its uses and applications. The main objective of this study was to determine whether electrospun P34HB fibres would accommodate viability, growth and differentiation of mouse adipose-derived stem cells (mASCs)., Materials and Methods: In the present study, we looked at P34HB in two forms, electrospun P34HB fibres and P34HB film. Morphology of electrospun P34HB fibres and P34HB film were characterized using scanning electron microscopy, fluorescence microscopy and confocal laser scanning microscopy, after cell seeding. Cell adhesion, proliferation and cytotoxicity tests were conducted on both by MTT and CCK-8 assays, respectively. After being cultured with osteogenic induction, expression of adipogenic genes Runx2, OPN and OCN, were examined by real-time PCR., Results: By scanning electron microscopy, light microscopy and confocal laser scanning microscopy, we observed that the mASCs grew well associated with the P34HB materials. After MTT and CCK-8 assay, we concluded that P34HB would, indeed, be a material suitable for further cell adhesion and proliferation studies. More importantly, we found that the P34HB matrices promoted expression of Runx2, OPN and OCN with osteogenic induction., Conclusions: In this investigation, we can confirm that the electrospun P34HB fibres accommodated survival, proliferation and differentiation of mASCs, and we have been able to draw the conclusion that fibre scaffolds produced by the electrospinning process are promising for application of bone tissue engineering., (© 2014 John Wiley & Sons Ltd.)

Development of biodegradable polymers-based scaffolds for tissue engineering is a promising trend in bioengineering. The electrospun scaffolds from poly(3-hydroxybutyrate) (PHB) were produced using different additives that changed the physical and chemical characteristics of the products. As a result, the construct consisting of interwoven threads of different diameter (0.8-3.4 mm) were obtained, the smallest diameter was observed in the threads from the PHB using tetrabutilammonium iodide (TBAI) and titanium oxide II (TiO2) as additives. Mesenchymal stem cells (MSC) were cultivated on the scaffolds for the biocompatibility evaluation of obtained materials. Cells viability was determined by the XTT assay test. It was shown that the scaffold from the interwoven threads of lowest diameter is most favorable for MSC growth in comparison with the polymer film and scaffolds from the threads of larger diameter. Thus, it was shown that the biocompatibility of electrospun PHB scaffolds depended on their microstructure. The obtained data can be used for development of scaffolds for tissue engineering.

The development of biomaterials for myocardial tissue engineering requires a careful assessment of their performance with regards to functionality and biocompatibility, including the immune response. Poly(3-hydroxybutyrate) (PHB), poly(e-caprolactone) (PCL), silk, poly-lactic acid (PLA), and polyamide (PA) scaffolds were generated by electrospinning, and cell compatibility in vitro, and immune response and cardiac function in vitro and in vivo were compared with a noncrosslinked collagen membrane (Col) control material. Results showed that cell adhesion and growth of mesenchymal stem cells, cardiomyocytes, and cardiac fibroblasts in vitro was dependent on the polymer substrate, with PHB and PCL polymers permitting the greatest adhesion/growth of cells. Additionally, polymer substrates triggered unique expression profiles of anti- and pro-inflammatory cytokines in human peripheral blood mononuclear cells. Implantation of PCL, silk, PLA, and PA patches on the epicardial surface of healthy rats induced a classical foreign body reaction pattern, with encapsulation of polymer fibers and induction of the nonspecific immune response, whereas Col and PHB patches were progressively degraded. When implanted on infarcted rat heart, Col, PCL, and PHB reduced negative remodeling, but only PHB induced significant angiogenesis. Importantly, Col and PHB modified the inflammatory response to an M2 macrophage phenotype in cardiac tissue, indicating a more beneficial reparative process and remodeling. Collectively, these results identify PHB as a superior substrate for cardiac repair.

Porous polyhydroxybutyrate (PHB)-chitosan biopolymer scaffolds were prepared by co-precipitation from biopolymer solutions with propylene carbonate and acetic acid as solvents. A change of the fibrous character of chitosan precipitates to globular shaped forms with a polyhydroxybutyrate addition was found in suspensions. Scaffolds differ by porosity and morphology of polymers in microstructures, while chitosan represented more compact plate-like fibers and PHB characterized mainly fine fibrous globular agglomerates. Two structurally dissimilar phase regions were verified in blended scaffolds. A rise in the number of smaller pores, and fine structured polymer forms with PHB content were observed in the scaffolds. A significant reduction in the average molecular weight of biopolymers was found in pure chitosan scaffold, this after precipitation of the chitosan in the presence of propylene carbonate and in blends after mutual biopolymer mixing. Interactions between shortened chitosan chains, PHB and chitosan biopolymers in the blends were observed. An excellent fibroblast proliferation was found in scaffolds prepared from biopolymer blends.

Electrospinning can produce nanofibrous scaffolds that mimic the architecture of the extracellular matrix and support cell attachment for tissue engineering applications. In this study, fibrous membranes of polyhydroxybutyrate (PHB) with various loadings of poly(L-lactide-co-ε-caprolactone) (PLCL) were successfully prepared by electrospinning. In comparison to PLCL scaffolds, PLCL blends with PHB exhibited more irregular fibre diameter distributions and higher average fibre diameters but there were no significant differences in pore size. PLCL/PHB scaffolds were more hydrophilic (<120°) with significantly reduced tensile strength (ca. 1 MPa) compared to PLCL scaffolds (150.9 ± 2.8° and 5.8 ± 0.5 MPa). Increasing PLCL loading in PHB/PLCL scaffolds significantly increased the extension at break, (4-6-fold). PLCL/PHB scaffolds supported greater adhesion and proliferation of olfactory ensheathing cells (OECs) than those exhibiting asynchronous growth on culture plates. Mitochondrial activity of cells cultivated on the electrospun blended membranes was enhanced compared to those grown on PLCL and PHB scaffolds (212, 179, and 153%, resp.). Analysis showed that PLCL/PHB nanofibrous membranes promoted cell cycle progression and reduced the onset of necrosis. Thus, electrospun PLCL/PHB composites promoted adhesion and proliferation of OECs when compared to their individual PLCL and PHB components suggesting potential in the repair and engineering of nerve tissue.

Nanotholits is an osteoinductor or be, stimulates the bone regeneration, enabling bigger migration of the cells for formation of the bone tissue regeneration mainly because nanotholits are rich in minerals considered essential to the bone mineralization process on a protein matrix (otolin) as hydroxiapatite. In order to improve its biodegrability and bioresorption in new platforms for tissue engineering, it was electrospun PHB/nanotholits from aqueous solutions of this polymer at concentrations of nanotholits 1% (w/v) and compared morphological and thermal properties with PHB/nanotholits casting films. Electrospun PHB/nanotholits mats presents more symmetric nanopore structure than casting films mats observed by SEM images mainly because the orientation of pores along the longitudinal direction of the electrospun fibers. Nanotholits influences in PHB electrospun/casting was analyzed using transmission infrared spectroscopy (FTIR). TGA showed similar thermal properties but DSC showed distinct thermal properties and crystallinity process of the developed bionanocomposite mainly because of different processing.

Polyhydroxyalkanoates (PHAs) are hydrophobic biodegradable thermoplastics that have received considerable attention in biomedical applications due to their biocompatibility, mechanical properties, and biodegradability. In this study, the degradation rate was regulated by optimizing the interaction of parameters that influence the enzymatic degradation of P(3HB) film using response surface methodology (RSM). The RSM model was experimentally validated yielding a maximum 21 % weight loss, which represents onefold increment in percentage weight loss in comparison with the conventional method. By using the optimized condition, the enzymatic degradation by an extracellular PHA depolymerase from Acidovorax sp. DP5 was studied at 37 °C and pH 9.0 on different types of PHA films with various monomer compositions. Surface modification of scaffold was employed using enzymatic technique to create highly porous scaffold with a large surface to volume ratio, which makes them attractive as potential tissue scaffold in biomedical field. Scanning electron microscopy revealed that the surface of salt-leached films was more porous compared with the solvent-cast films, and hence, increased the degradation rate of salt-leached films. Apparently, enzymatic degradation behaviors of PHA films were determined by several factors such as monomer composition, crystallinity, molecular weight, porosity, and roughness of the surface. The hydrophilicity and water uptake of degraded salt-leached film of P(3HB-co-70%4HB) were enhanced by incorporating chitosan or alginate. Salt-leached technique followed by partial enzymatic degradation would enhance the cell attachment and suitable for biomedical as a scaffold.

The potential of constructs comprising induced pluripotent stem (iPS) cells and biopolymers can be high for neurological surgery practice, if the systematic activity of neuronal regeneration is clarified. This study shows a guided differentiation of iPS cells toward neurons in neuron growth factor (NGF)-grafted poly(ε-caprolactone) (PCL)-poly(β-hydroxybutyrate) (PHB) scaffolds. The porosity of PCL-PHB scaffolds enhanced with increasing the concentration of salt particles (porogen) and the weight percentage of PCL. An increase in the graft concentration of NGF elevated the atomic ratios of N/C and O/C on the surface of NGF-grafted PCL-PHB scaffolds. In addition, incorporating heparin and NGF promoted the adhesion and viability of iPS cells in constructs. When the weight percentage of PCL increased, the viability of iPS cells reduced; however, more PCL in constructs benefited the adhesion of iPS cells. Under the influence of heparin and NGF, a high weight percentage of PCL and a long inductive period improved iPS cells to differentiate into neuron-like cells carrying βIII tubulin and inhibited other differentiation(s). The material-driven differentiation in NGF-grafted PCL-PHB constructs can be promising in guiding iPS cells to produce neurons for nerve tissue engineering., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

This study aims at investigating the behavior in terms of the proliferation and skeletal muscle differentiation capability of two myoblastic cell lines, C2C12 and H9c2, on both isotropic and anisotropic electrospun nanofibrous poly(hydroxybutyrate) (PHB) scaffolds, as well as on PHB films and polystyrene controls. After a careful characterization of the matrices in terms of surface morphology, surface roughness and mechanical properties, the proliferation rate and the capability of the two cell lines to form skeletal myotubes were evaluated. Genetic analyses were also performed in order to assess the differentiation level of the cells on the different substrates. We demonstrated that the aligned nanofibrous mesh decreases the proliferation activity and provides a higher differentiative stimulus. We also clarified how the nanofibrous substrate influences myotube formation, and quantified a series of myotube-related parameters for both C2C12 and H9c2 cells.

The modification of flax fibers to create biologically active dressings is of undoubted scientific and practical interest. Flax fibers, derived from transgenic flax expressing three bacterial genes for the synthesis of poly-3-hydroxybutyric acid (PHB), have better mechanical properties than unmodified flax fibers; do not show any inflammation response after subcutaneous insertion; and have a good in vitro and in vivo biocompatibility. The aim of this study was to examine the applicability of composites containing flax fibers of genetically modified (M50) or non-modified (wt-Nike) flax within a polylactide (PLA) matrix for bone regeneration. For this, the mRNA expression of genes coding for growth factors (insulin-like growth factor IGF1, IGF2, vascular endothelial growth factor), for osteogenic differentiation (alkaline phosphatase, osteocalcin, Runx2, Phex, type 1 and type 2 collagen), and for bone resorption markers [matrix metalloproteinase 8 (MMP8), acid phosphatase type 5] were analyzed using quantitative real-time polymerase chain reaction. We found a significant elevated mRNA expression of IGF1 with PLA and PLA-wt-Nike composites. The mRNA amount of MMP8 and osteocalcin was significantly decreased in all biocomposite-treated cranial tissue samples compared to controls, whereas the expression of all other tested transcripts did not show any differences. It is assumed that both flax composites are able to stimulate bone regeneration, but composites from transgenic flax plants producing PHB showed faster bone regeneration than composites of non-transgenic flax plants. The application of these linen membranes for bone tissue engineering should be proved in further studies.

Nanofibers were prepared by electrospinning from pure polyvinyl alcohol (PVA), polyhydroxybutyrate (PHB), and their blends. Miscibility and morphology of both polymers in the nanofiber blends were studied by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and differential scanning calorimetry (DSC), revealing that PVA and PHB were miscible with good compatibility. DSC also revealed suppression of crystallinity of PHB in the blend nanofibers with increasing proportion of PVA. The hydrolytic degradation of PHB was accelerated with increasing PVA fraction. Cell culture experiments with a human keratinocyte cell line (HaCaT) and dermal fibroblast on the electrospun PHB and PVA/PHB blend nanofibers showed maximum adhesion and proliferation on pure PHB. However, the addition of 5 wt % PVA to PHB inhibited growth of HaCaT cells but not of fibroblasts. On the contrary, adhesion and proliferation of HaCaT cells were promoted on PVA/PHB (50/50) fibers, which inhibited growth of fibroblasts.

Efforts to mineralize electrospun hydrophobic polyester scaffold often require prior surface modification such as plasma or alkaline treatment, which may affect the mechanical integrity of the resultant scaffold. Here through rational design we developed a series of polyurethane block copolymers containing poly[(R)-3-hydroxybutyrate] (PHB) as hard segment and poly(ethylene glycol) (PEG) as soft segment that could be easily fabricated into mineralizable electrospun scaffold without the need of additional surface treatment. To ensure that the block copolymers do not swell excessively in water, PEG content in the polymers was kept below 50 wt %. To obtain good dry and hydrated state mechanical properties with limited PEG, low-molecular-weight PHB-diol with M(n) 1230 and 1790 were used in various molar feed ratios. The macromolecular characteristics of the block copolymers were confirmed by (1)H NMR spectroscopy, gel permeation chromatography (GPC), and thermal gravimetric analyses (TGA). With the incorporation of the hydrophilic PEG segments, the surface and bulk hydrophilicity of the block copolymers were significantly improved. Differential scanning calorimetry (DSC) revealed that the block copolymers had low PHB crystallinity and no PEG crystallinity. This was further confirmed by X-ray diffraction analyses (XRD) in both dry and hydrated states. With short PHB segments and soft PEG coupled together, the block copolymers were no longer brittle. Tensile measurements showed that the block copolymers with higher PEG content or shorter PHB segments were more ductile. Furthermore, their ductility was enhanced in hydrated states with one particular example showing increment in strain at break from 1090 to 1962%. The block copolymers were fabricated into an electrospun fibrous scaffold that was easily mineralized by simple incubation in simulated body fluid. The materials have good potential for bone regeneration application and may be extended to other applications by simply coating them with other biologically active substances.

The selection of an appropriate scaffold represents one major key to success in tissue engineering. In cardiovascular applications, where a load-bearing structure is required, scaffolds need to demonstrate sufficient mechanical properties and importantly, reliable retention of these properties during the developmental phase of the tissue engineered construct. The effect of in vitro culture conditions, time and mechanical loading on the retention of mechanical properties of two scaffold types was investigated. First candidate tested was a poly-glycolic acid non-woven fiber mesh, coated with poly-4-hydroxybutyrate (PGA/P4HB), the standard scaffold used successfully in cardiovascular tissue engineering applications. As an alternative, an electrospun poly-epsilon-caprolactone (PCL) scaffold was used. A 15-day dynamic loading protocol was applied to the scaffolds. Additionally, control scaffolds were incubated statically. All studies were performed in a simulated physiological environment (phosphate-buffered saline solution, T=37 degrees C). PGA/P4HB scaffolds showed a dramatic decrease in mechanical properties as a function of incubation time and straining. Mechanical loading had a significant effect on PCL scaffold properties. Degradation as well as fiber fatigue caused by loading promote loss of mechanical properties in PGA/P4HB scaffolds. For PCL, fiber reorganization due to straining seems to be the main reason behind the brittle behavior that was pronounced in these scaffolds. It is suggested that those changes in scaffolds' mechanical properties must be considered at the application of in vitro tissue engineering protocols and should ideally be taken over by tissue formation to maintain mechanically stable tissue constructs.