Search

The reliability of low-voltage inverter-fed motors is highly dependent on the inception of partial discharges. The effect of impulsive waveform parameters must be investigated to predict the repetitive partial discharge inception voltage (RPDIV) and define test procedures that can indicate properly the behavior in service of the insulation system. This paper focuses on the RPDIV of magnet wires using twisted pairs subjected to repetitive unipolar impulsive voltage waveforms. The effects of supply frequency (5 to 200 kHz) at pressure levels that are typical for aircraft (20 to 100 kPa) is examined. Results show that RPDIV steadily decreases with frequency up to 100 kHz where it reaches a plateau. This behavior is explained as an effect of the oscillations that inevitably exist in the applied voltage waveform. Therefore, a conservative estimate of the RPDIV could be achieved by raising the supply frequency well above the operation frequency. In the experiments, the RPDIV is decreasing linearly with pressure. If this behavior could be confirmed for other insulation systems, the design of systems working at pressures typical of aircraft would result relatively easy. [ABSTRACT FROM AUTHOR]

This work assesses the initial and crucial part of electrical treeing degradation, the inception stage, focusing on its dependence on applied voltage waveform and frequency. Tests have been performed on needle-plane configuration samples in solids and gels. A physical model has been formulated through an adaptation of an established theory for solids in which electrical tree inception is related to damage-producing injection currents. The voltage rise time appeared to be the most important parameter influencing the tree inception in the gel, while in the solid material the frequency is more relevant. The analysis leads to the conclusion that tree inception in gels is due to a single high-energy event, in contrast to what is commonly known for solids where damage accumulation takes place. A tree inception model is proposed for the gel, in which initiation is driven by a pressure wave generated by the electric field and the space charge injected into the sample. The model fits the experimental data and may be used to predict the tree initiation for different waveforms and voltage values. [ABSTRACT FROM AUTHOR]

The electrical withstand capabilities of polyethylene films and ad hoc prepared PE sandwich samples containing controlled cavities inside, both coated with organic-inorganic hybrid thin layers also modified with graphene oxide, have been investigated. While films have been subjected to breakdown tests, samples with cavities have been exposed to partial discharge (PD) induced electrical ageing, valuating the different evolution of the damage due to PD activity. Experimental results highlight the positive effect brought by the presence of the hybrid coating and in particular of the coating containing also graphene oxide on the electrical performance of the samples. [ABSTRACT FROM AUTHOR]

This paper reviews results of partial discharge measurements and accelerated life tests performed on models of random and form wound insulation systems subjected to impulse voltage waveforms. The goal is to highlight how the features of the supply voltage affect the partial discharge activity and how this, eventually, reflects on the endurance of the insulation system. The most salient results are that, for both types of insulation systems, short rise times trigger PD of large magnitude, which are able to erode the insulation system faster than the partial discharges incepted using waveforms with longer rise times. In particular, failure times estimated by tests under sinusoidal voltages can be overly optimistic in assessing the long-term behavior of the insulation system subjected to impulse voltage waveforms. Frequency also is very important, as it controls the interplay between physical and chemical degradation rates. As a result, above partial discharge inception voltage the frequency acceleration rule does not hold, and can lead therefore to excessively optimistic results. [ABSTRACT FROM AUTHOR]

In this work, we compare the dielectric withstand performance of nanofluids prepared using Shell Diala D as a base fluid, and magnetite, graphene oxide and silicone dioxide as nanoadditives. The ac withstand capability of the nanofluids was investigated as well as partial discharge inception voltage, partial discharge and repetition rate under ac, dc positive and dc negative voltages. The results indicate that, for all nanofluids, nanoparticle concentrations around 0.2 g/l enhance dielectric withstand properties under quasi uniform fields. Under divergent fields, partial discharge characteristics are improved under ac conditions. Under dc conditions silica nanofluid performs better than mineral oil, but the other two nanofluids do not perform well. [ABSTRACT FROM AUTHOR]

High voltage equipment designed for DC applications is stressed differently from ac equipment. Most notably, the load conditions of the equipment play a major role in determining the electric field distribution in insulation under dc, due to the temperature dependence of conductivity. Additionally, polarization and space charge phenomena impose a time dependent behavior on the stress distribution. This has major consequences for the way in which degradation of the insulation under dc stress takes place. The nature of the stresses under dc may lead to accelerated degradation processes which could result in early breakdown of the insulation. This paper provides an overview of the stress conditions specific for dc application and highlights via which routes they may lead to failure. The stress distributions in converter transformers and dc cable systems will serve as typical examples. [ABSTRACT FROM AUTHOR]

The dependence of endurance test results on repetitive square wave voltage waveform parameters is investigated in this paper focusing on crossed pair specimens made of polyamide-imide enameled wires. Endurance tests carried out on crossed pairs above partial discharge inception voltage using both sinusoidal and square wave voltages show that lifetimes can be influenced significantly by voltage waveform parameters (rise time and frequency). Partial discharge statistics, recorded from test beginning to breakdown, are used to explain the remarkable differences associated with voltage waveform parameters. According to this study, the influence of voltage waveform parameters should be carefully considered in order to obtain effective evaluation of inverter-fed motor insulation systems. [ABSTRACT FROM AUTHOR]

This paper focuses on the influence of repetitive square wave voltage rise time on partial discharge pulse characteristics in the ultra-high frequency range. Paerial Discharge (PD) tests on single-point contact crossed pairs were carried out using repetitive square wave voltages with a wide range of rise times, from 200 ns to 400 μs, including also 50 Hz sinusoidal voltage waveforms. Experimental results show that rise time has a significant influence on magnitude and frequency spectrum of PD pulses. Voltages of shorter rise times generate larger PD pulses with a predominance of high frequency components in the energy spectrum. Interpretations are presented for this phenomenon. [ABSTRACT FROM AUTHOR]

This paper focuses on the limits of partial discharge apparent charge estimation and calibration using an unified approach. The fundamental problems that prevent accurate apparent charge estimates (resonances, attenuation and partial discharge pulse splitting) are tackled through this approach, highlighting the physical limitations that prevent partial discharge charge to be measured properly. The feasibility of calibration of Ultra-Wide Bandwidth measurement systems, something that is not treated in the IEC 60270 standard, is also discussed. [ABSTRACT FROM AUTHOR]

A novel method for measurement and interpretation of PD phenomena in inverter-fed motors is discussed in this paper. The interpretation of PD measurements is carried out resorting to the direct-quadrature (dq) transform of the three voltages at motor terminals at the instant a PD event occurs. New tools (the dq loci, dq Hq and dq Hn patterns) are proposed to infer PD activity in a statistical way, similar to that used under AC supply. The method has been validated through tests on motorettes. In addition, measurements on low-voltage inverter-fed motors subjected to repetitive surges till breakdown are reported to support the capability of the method to infer onsetting faults. Measurements are performed through a reliable and lightweight (thus suitable for, e.g., automotive or avionics applications) antenna coupler characterized by excellent signal-to-nose ratio. [ABSTRACT FROM AUTHOR]

This paper deals with partial discharge (PD) measurements on inverter-fed motors. They are performed by means of a broadband sensor-filter system that allows PD signal to be recorded, damping the noise generated by the commutation interference of electronic power supply. In this way, online or offline measurements can be carried out with the purpose of evaluating the presence of PDs in adjustable speed drives, which often constitute the main cause of winding insulation degradation and premature breakdown. An offline testing technique is also proposed to offer an insight into PD activity and a more precise location of PD sources. These techniques can allow improved quality control and diagnostics on power-electronic-controlled motors. [ABSTRACT FROM AUTHOR]

An investigation on partial discharge (PD) propagation in power cables is carried out in this paper with the aim of inferring limits for PD detection as a function of the distance between PD source and detector. Although this problem has not an exact solution unless noise levels are not specified, useful information concerning detectability and error in estimates are provided in this paper for both medium and high voltage polymeric cables. The issue of calibrator characteristics with respect to sensitivity detection is also tackled. [ABSTRACT FROM AUTHOR]

A new technique for partial discharge (PD) source location in cable systems is presented in this paper. Such technique, here referred to as amplitude-frequency (AF) mapping, is based on the influence of attenuation and dispersion phenomena on PD pulse time and frequency characteristics. A comparative evaluation with other two well-known location techniques, i.e., time-domain reflectometry (TDR) and arrival time analysis (ATA) is presented through working cases. The results indicate that while TDR is appropriate for short cable systems, for longer cable systems, location by AF mapping can be obtained directly from PD testing, without additional efforts. The location thus achieved is, in most cases, accurate enough to allow maintenance practices to be carried out effectively. In some cases, ATA can be necessary to refine location and resolve ambiguities. [ABSTRACT FROM AUTHOR]

This paper deals with the effect of supply frequency on partial discharge phenomena. Results of measurements performed on artificial and practical test objects are compared with computer simulations based on physical models. This comparative analysis points out and explains the differences in partial discharge phenomena observed in tests performed at different frequencies (from 0.1 to 300 Hz). The consequences associated to the use of different supply frequencies in practical applications are, eventually, outlined. [ABSTRACT FROM AUTHOR]

Inter-time (i.e., the time that separates a PD event from the next one) distribution analysis has been recently proposed as a tool to infer the presence of trees in solid insulation systems. In this paper, inter-time distribution analysis is improved to infer more accurately trees at an early growth stage. Measurements from both artificial specimens as well as practical objects are presented to support the effectiveness of this tool. Moreover, considerations on inter-time analysis robustness with respect to both noise interference and other partial discharge sources are reported. [ABSTRACT FROM AUTHOR]

An experimental investigation of the behavior of partial discharges occurring in insulation cavities as a function of light irradiation conditions is presented in this paper. Partial discharge inception voltage (PDIV) measurements were performed for different irradiation conditions of the test objects (visible light, of variable intensity, ultra violet (UV) light or absence of irradiation), defect geometry and conductivity of insulating material. It is shown that changes of such factors involve con siderable alteration of partial discharge inception features, in terms of both inception voltage and delay time. Depending on applied field, defect geometry, insulating material characteristics and irradiation condition, in fact, partial discharge inception voltage may be influenced prevailingly by background radiation, as generally stated in literature, or by field-assisted electron detrapping from material. cavity interface. [ABSTRACT FROM AUTHOR]

Applications of a new methodology, aimed at the identification of defects occurring in insulation systems of HV apparatus and based on partial discharge (PD) measurements, are presented in this paper. This methodology relies upon the digital acquisition of a large amount of PD pulses and separates the acquired pulses into homogeneous sub-classes. Signal processing tools recognize the presence of noise among the different classes. Identification of basic PD source typologies (i.e., internal, corona and surface discharges) is then achieved, resorting to fuzzy algorithms. The proposed procedure is applied to measurements performed on different HV apparatus, such as cables, transformers and rotating machines. The purpose of this paper is to show that the identification process is robust, regarding the measuring circuit, and flexible, so that it can constitute an advanced tool for condition based maintenance, guiding maintenance experts in making decisions on the condition of the insulation system under test. [ABSTRACT FROM AUTHOR]

In this paper, the PD properties of an ester oil/PB and a mineral oil/PB system undergoing a moisture transient are investigated using a needle-plane electrode under natural cooling. The temperature, moisture concentration and water activity of the oil are continuously monitored. Moreover, an improved moisture diffusion model is developed by using COMSOL Multiphysics to verify the experimental results. The measurement results show that there is a sharp reduction of partial discharge inception voltage (PDIV) or a sudden increase of PD intensity in the process of natural cooling for both ester oil and mineral oil system. However, the PDs extinguish gradually after the occurrence of the minimum of PDIV. For the cooling mode selected in this study, the minimum of PDIV for the ester oil system appears in the third hour after cooling begins, while it is about in the second hour for the mineral oil system. In addition, the simulation results are consistent with the experimental data. [ABSTRACT FROM AUTHOR]

The most effective method for insulation assessment in an electrical power apparatus is partial discharge (PD) detection. During measurements, the interference from the background environment hampers the PD signal and reduces its measurement accuracy. This article discusses on the implementation of a Hankel matrix (HM)-based fast singular value decomposition (H-FSVD) technique for removing noise from the PD signals. The data are first represented into HM structure, with appropriate sampling then using the Lanczos process, the HM size is reduced and through singular spectral analysis thresholds are fixed for noise detection and removal. This algorithm has been examined on simulated as well as PD signals measured on two different laboratory environments from transformers with real and simulated noise. The experiment is part of a series of experiments to detect PD patterns related to realistic transformer defects. The denoising performance of H-FSVD is compared with the wavelet-based denoising methods, empirical mode decomposition method, and normal SVD. Numerical results show that H-FSVD efficiently removes the noise with less computation time, even for large size data. [ABSTRACT FROM AUTHOR]

Detection and measurement of partial discharge (PD) phenomena combined with the separation and identification of PD sources is the way to achieve effective insulation integrity assessment. However, during measurement, PD signals are coupled with interferences (discrete spectral, pulsive, and white noises). Recovering PD signals from such interferences would improve PD source separation (thus identification), but still remains a challenging task. Several denoising methods have been proposed to suppress interferences. However, using a universal method to achieve interference removal is probably impossible, as the characteristics of the interferences are distinct. This study proposes a novel low‐rank H‐Matrix‐based singular value decomposition (SVD) filter (H‐SVD) that removes different types of interferences. Denoising is done by projecting the measured pulse in a lower dimensional signal space. To assess the effectiveness of the proposed method, H‐SVD filter is first applied to simulated PD data and later on real‐time PD data with the introduction of three different types of synthetic noises. The results of the evaluation metrics confirm that H‐SVD has significant performance improvements compared to existing state‐of‐the‐art PD denoising methods. [ABSTRACT FROM AUTHOR]

This paper is focused on the reliability evaluation of an electric vehicle (EV) motor based on hairpin technology. Besides bearings (not discussed here), the weak point of an electric motor is its insulating system. For inverter-fed motors, the inception of partial discharges might lead to failure in a matter of days, and thus, deserves particular attention. Qualification and lifetime evaluation of inverter-fed machines are described in IEC 60034-18-41, which specifies accelerated aging procedures and considers partial discharge inception as the end-of-life criterion. This standard was used as a reference for this paper. The only exception is that insulation models were subjected to the mechanical stress profile reported in the ISO 16750-3-2012 standard since an automotive motor is subject to significant vibrations during its operation. From the tests performed, we observed that, with the hairpin technology, turn-to-turn is the weakest link in the insulation system. All the insulation models were partial discharge (PD) free from the beginning of the tests to breakdown and the root cause for breakdown was, in all cases, traced back to cracks on the surface of the insulation. This suggests that, depending on insulating enamel thickness and conductor geometry, some insulation systems are intrinsically PD free by design, despite the effect of aging. Considering the severe vibration profiles typical of EVs, and the principal breakdown mechanism (cracking of the insulation), mechanical stress coupled with thermal stress appears as the main aging driver. Therefore, this paper spotlights the lack of proper standards for the qualification of automotive electric motors and hints at the possibility that IEC 60034-18-41 considers dealing with motors that might be intrinsically partial discharge free even after long-term exposure to operational stresses. [ABSTRACT FROM PUBLISHER]

In the framework of developing defect-based life models, in which breakdown is explicitly associated with partial discharge (PD)-induced damage growth from a defect, ageing tests and PD measurements were carried out in the laboratory on polyethylene (PE) layered specimens containing artificial cavities. PD activity was monitored continuously during aging. A quasi-deterministic series of stages can be observed in the behavior of the main PD parameters (i.e. discharge repetition rate and amplitude). The evolution of the parameters reflects the physicalchemical changes taking place at the dielectric/cavity interface during the aging process. PD activity shows similar time behavior under constant cavity gas volume and constant cavity gas pressure conditions, suggesting that the variation of PD parameters may not be attributed to the variation of the gas pressure. It is speculated that the change of PD activity is related to the composition of the cavity gas, as well as to the properties of dielectric/cavity interface. [ABSTRACT FROM AUTHOR]

This paper presents a methodology for the diagnosis of HVDC systems based on partial discharge analysis. In particular, the characteristics of partial discharge phenomena from different test objects are highlighted, with the aim of providing tools enabling automatic identification of the type of PD, as well as noise and disturbance rejection, for on-line and/or off-line PD testing of HVDC equipments. The results show that, using a fuzzy identification system based on higher-order moments of the PD magnitude and inter-time distributions, corona phenomena can be identified easily, whereas it is sometimes difficult to distinguish between internal and surface partial discharge sources. For this purpose, the characteristics of internal and surface partial discharge phenomena as a function of influence variables as humidity and temperature are reported. By exploiting these characteristics through on-line/off-line PD monitoring systems, accurate identification of the PD phenomena affecting an electrical apparatus can be attained. [ABSTRACT FROM AUTHOR]

This paper reports and discusses qualification and type test procedures for random wound motors as specified in IEC Technical Specification 60034-18-41. Since laboratory tests dealing with off-line partial discharges measurements followed by life tests showed that motors qualified as good can fail in very short times, an extensive investigation on the causes of such discrepancy and, in particular, on the differences existing between the stresses applied during off-line tests and in service is described. In addition, the results of partial discharge measurements performed on crossed pairs are presented, highlighting how the differences in the applied voltage waveform can influence the Repetitive Partial Discharge Inception Voltage. Suggestions to improve the off-line test procedure and related equipment are eventually discussed. [ABSTRACT FROM PUBLISHER]

To address the reliability of rotating machine insulation, the International Electrotechnical Commission implemented new standards and technical specifications that are relevant to low-voltage and medium-voltage inverter-fed motors. Insulation evaluation under such power supply relies upon partial discharge (PD) measurements and accelerated life tests, which should be conducted (at least for the turn-to-turn insulation) under impulsive voltage waveform. The effect of impulsive voltage parameters on PD inception voltage and, in particular, endurance tests must be investigated to design test procedures that can indicate insulation quality and its behavior in service. This paper examines the effect of repetitive impulsive voltage waveform parameters on PD and the endurance (life) of organic insulation for rotating machine wires based on experiments performed on single-contact crossed pairs. Results show that the features of repetitive voltage impulse affect PD time and frequency characteristics, PD phase distribution, and endurance. Consequently, evaluation of insulation subjected to power electronics waveforms should take into account the appropriate choice of impulsive voltage parameter to fit to the type of PD phenomenology occurring in service conditions. [ABSTRACT FROM PUBLISHER]

The aim of this paper is to infer partial discharge (PD) detection limits in extruded cables as a function of the distance between PD source and detection point. The investigation is carried out for different types of detectors, from IEC 60270-compliant to ultra-wide bandwidth systems. For this purpose, a medium voltage cable has been modeled as a transmission line with frequency-dependent parameters accounting for skin effect, dielectric and semicon characteristics. Pulse propagation through the cable has been predicted for very tong distances. Different filters have been used to simulate different detectors, emphasizing the behavior of these systems, particularly the features of sensitivity, noise rejection, PD source separation and PD source localization. [ABSTRACT FROM AUTHOR]

In this paper, a pioneer partial discharge (PD) loop antenna sensor is presented and examined. It is made of a 70-turn square planar inductor with a side length of 1.8 mm, which is fabricated on top of a silicon substrate in complementary metal oxide semiconductor technology. The microsensor ability to detect corona PD is demonstrated once connected in series with a 60 dB gain amplifier. The behavior is studied at different separation distances from the line through which the PD pulses flow. At 5 cm away, a damped sinusoidal induced voltage with an amplitude of about 100 mV has been measured. The output signal spectrum is highly concentrated around a central resonance frequency of ∼5 MHz. The microsensor response is compared with those of other industrial sensors from Techimp, i.e., horn antennas and high-frequency current transformer sensors. The presented on-chip sensor can be considered a non-intrusive competing solution compared with other heavy and expensive commercial sensors due to its lightweight, compact size, and low cost. In addition, it shows an acceptable signal to noise ratio compared with other commercial electromagnetic wave-based sensors. [ABSTRACT FROM AUTHOR]

Partial discharge inception voltage measurements under repetitive impulsive voltages play an essential role in evaluating the reliability of inverter-fed low voltage rotating machines. Using impulsive voltages, partial discharge (PD) signals and the disturbance induced by power electronics switches have often similar energy distribution in the frequency domain. Thus, PD test technologies used with sinusoidal voltages are no longer effective. Under repetitive impulsive voltages, ultra-high frequency detection is recommended to couple high-frequency spectral components from the PD and remove the low-frequency disturbance coming from power electronics. However, to obtain high signal to noise (S/N) ratio, the parameters of the antenna used for PD detection should be designed considering the PD and the disturbance energy distributions in the frequency domain. In this paper, we discuss the design and show the properties of an antenna with Archimedes plane spiral structure intended for PD detection under repetitive impulse voltages. The simulation shows that the antenna has low voltage standing wave ratio (<2) and improved directivity in the frequency range from 0.5 to 2 GHz. Moreover, PD tests performed using repetitive square waves with different rise times demonstrate that the designed antenna can receive PD signals efficiently with high S/N. [ABSTRACT FROM AUTHOR]

Dealing with electrical rotating machines fed by voltage converters, understanding the effect of impulsive voltage parameters on partial discharge features is of great importance to select appropriate impulsive voltage to perform partial discharge inception voltage measurements. Similarly, the dependence of insulation endurance on voltage parameters might help to develop qualification tests providing more accurate evaluation of insulation performance. The effect of voltage duty cycle on partial discharge characteristics and endurance of inverter-fed motor insulation were investigated through a large number of tests performed on single-contact crossed enameled wires under bipolar repetitive impulse wave voltages. The partial discharge pattern, magnitude, repetition rate show that short impulsive voltage duration (i.e. small duty cycles), can induce asymmetric PD patterns and reduce the probability of PD inception at the falling flanks of impulsive voltages. Moreover, the endurance tests indicate that the duty cycle of the repetitive square wave voltage can affect the insulation endurance significantly. Repetitive square wave voltages with small duty cycles tend to overestimate endurance. Accordingly, when performing partial discharge inception voltage and endurance tests on insulation of inverter-fed motors, the influence of duty cycle should be carefully considered. [ABSTRACT FROM AUTHOR]

To ensure insulation system reliability of rotating machines driven by power electronics, accelerated tests under repetitive impulsive voltages should be performed on turn-to-turn insulation according to the standards provided by the International Electrotechnical Commission. The parameters of repetitive impulsive voltage can significantly influence insulation lifetime, and thus, voltage parameters should be carefully controlled during the accelerated tests. To increase endurance test efficiency when testing many insulation specimens in parallel, the rise time of impulsive voltage should be controlled at certain constant values after the breakdown of one or more specimens to obtain objective endurance test results. This study provides a description of a novel square wave voltage generator used for the insulation evaluation of rotating machines driven by power electronics. A single-channel generator with variable rise times used for one specimen and a multi-channel generator with a constant rise time used to test five specimens in parallel are presented based on a push-pull solid-state switch. In the multi-channel generator, the RC parameter of the high-voltage circuit can be adjusted automatically by resorting to controlling units and a circuit structure after the breakdown of one or more samples when performing endurance tests on parallel specimens to keep the rise time of impulsive voltage at constant values. The multi-channel generator can significantly increase the endurance evaluation efficiency of the insulation systems of rotating machines fed by power electronics. [ABSTRACT FROM AUTHOR]

The purpose of this paper is to understand the pros and cons of aluminum conductors insulated with anodized aluminum for rotating machines used in aircraft. The investigation is focused on the breakdown voltage and partial discharge inception voltage of simple systems (crossed pairs, simplified coils). The results show that both breakdown voltage and partial discharge inception voltage are very sensitive to curvature radius and lower than those achieved using conventional copper conductors insulated with polymeric enamels. However, the operating temperature of the insulation (600 ?C) is extremely appealing. Therefore, it could be interesting to devise high temperature fillers and suitable manufacturing procedures to exploit this insulation system in specific applications, where the weight of the machine is the key factor for material selection. [ABSTRACT FROM AUTHOR]