Search

Perforation is used in multilayer tissue products, such as toilet and kitchen papers, as part of the converting process. Perforation facilitates the detachment of consecutive sheets by the user. The compromise between the strength required to detach a perforated sheet and the strength required to break a sheet affects the perforation efficiency. In this work, the mechanical behaviors of 15 commercial papers from different European producers were studied. A morphological analysis of the materials was performed, followed by the determination of their perforation efficiency (through tensile tests). A qualitative analysis of the cuts quality, along with a quantitative analysis of the same cuts dimensions was performed through an optical system. Finally, the stress concentration in the holes and the influence of the cuts distance were analyzed using a finite element model implemented in Abaqus/Standard finite element software. The results showed that a cut distance of 2.0 mm should not be used in these types of papers, and the perforation efficiency increased with the cut distance, regardless of the number of plies in the toilet paper. The stress concentration factor was also determined to have a limit value of 0.11. Papers above this limit value tear at the perforation line, as desired.

In this study, we evaluated the effect of bamboo bleached kraft pulp (BKP) on the strength of the coloring paper used for pear paper bags. The characteristics of bamboo BKP were measured to compare them with those of softwood BKP and hardwood BKP. Handsheets from bamboo and hardwood BKPs were prepared at various mixing ratios, and their strengths were then analyzed. After that, a mill trial was performed to produce a prototype of coloring paper with bamboo BKP, and the effect of bamboo BKP on the strength of the coloring paper was finally determined. The initial freeness and fiber shape of bamboo BKP were similar to those of hardwood BKP, although the average fiber length and curl of bamboo BKP were higher than those of hardwood. As the mixing ratio of bamboo BKP increased, the strength of the handsheets increased, indicating the enhancing effect of bamboo BKP on the strength of coloring paper. As a result of the mill trial of coloring paper in the specialty paper mill, it was found that the tensile strength increased by 27.8% and burst strength by 20.0% when bamboo chemical pulp replaced 20% of the hardwood chemical pulp. Therefore, it was concluded that bamboo chemical pulp can replace and improve the strength of hardwood chemical pulp for manufacturing coloring paper.

Our dependency towards wood has reduced the number of forests especially in Indonesia. Hence, many people tried to use another material as a replacement of wood. One of them is composite. Department of Industrial Engineering Universitas Sebelas Maret has developed paper-based composite using newspaper waste in Praktikum Perancangan Teknik Industri (PPTI) II. Unfortunately, the quality of composite is not so good. This paper tried to understand the effect of factors to responses and discover the best combination of factors to obtain the best responses. The responses of this experiment are tensile strength, bending strength and impact value. The factors of this experiment are paper pulp, PVAc glue and water. Taguchi method is used to find the appropriate orthogonal array and Particle Swarm Optimization method to find the optimum combination of the factors. Orthogonal array used in this experiment is L9 (34). Through analysis, all of the factors are significant to tensile and bending strength, but they are not significant to impact value. The best combination of factors is 175 grams paper pulp, 130 grams PVAc glue and 175 ml water. Optimum results obtained for tensile strength is 0.7595 N/mm2, bending strength is 4.873 N/mm2 and impact value is 0.0138 J/mm2.

Objectives: The objective of the study was to study the compressive strength of the partially replaced paper mill waste in cement. Methods/ Statistical analysis: The concrete cube specimen were prepared for compressive strength test. In this study, the cement has been replaced with 20%, 30%, 40% and 50% of hypo sludge. The specimens were cured for two different ages (7 days and 28 days) and tested for compressive strength. The quadratic polynomial prediction equation was proposed using Response Surface Methodology (RSM). The prediction model was developed using the experimental output results. Thus, the prediction model facilitates the further research work to be conducted by researchers on paper mill waste replacement. The rate analysis was also further carried out to show the cost effectiveness of using the waste replacement in cement. Findings: The test was conducted on the compressive strength (7 days and 28 days) of control specimen (0%) and partial replacement of 20%, 30%, 40% and 50% of cement using the hypo sludge. Thus, 20% replacement of cement using hypo sludge has shown good compressive strength than the control specimen. The cost of 20% paper mill waste was less when compared to the cost of control specimen. Novelty/ Applications: The compressive strength of 20% partial replacement of paper mill waste in cement can be used in further construction. The prediction model can be used to predict the future compressive strength of partially replaced paper mill waste concrete. Keywords: Ordinary Portland cement; Paper mill waste; Hypo sludge; Partial replacement; RSM

Based on publications related to the use of micro- and nanofibrillated cellulose (MNFC) in papermaking applications, three sets of parameters (intrinsic and extrinsic variables, furnish composition, and degree of dispersion) were proposed. This holistic approach intends to facilitate understanding and manipulation of the main factors describing the colloidal behavior in systems comprising of MNFC, pulp fibers, and additives, which directly impact paper product performance. A preliminary techno-economic assessment showed that cost reductions driven by the addition of MNFC in paper furnishes could be as high as USD 149 per ton of fiber (up to 20% fiber reduction without adverse effects on paper’s strength) depending on the cost of papermaking fibers. It was also determined that better performance in terms of strength development associated with a higher degree of MNFC fibrillation offset its high manufacturing cost. However, there is a limit from which additional fibrillation does not seem to contribute to further strength gains that can justify the increasing production cost. Further research is needed regarding raw materials, degree of fibrillation, and combination with polyelectrolytes to further explore the potential of MNFC for the reduction of weight of paper products.

Paper waste in the mockups design with regular, irregular, and amorphous patterns is a critical problem in digital printing presses. Paper waste reduction directly impacts production costs, generating business and environmental benefits. This problem can be mapped to the two-dimensional irregular bin-packing problem. In this paper, an iterated local search algorithm using a novel neighborhood structure to detect overlaps between amorphous shapes is introduced. This algorithm is used to solve the paper waste problem, modeled as one 2D irregular bin-packing problem. The experimental results show that this approach works efficiently and effectively to detect and correct the overlaps between regular, irregular, and amorphous figures.

In museum lighting, Chinese paper cultural relics are prone to cracking, embrittlement and other photochemical damage after absorbing the spectral energy of light sources. Owing to the different absorption and reflection characteristics of paper for different bands, optimizing the spectrum compositions of light sources can provide effective protection, the basis of which is to clarify the influence rule of spectra on the paper. However, the methods of color difference and Raman spectroscopy, which are widely used in the current research, cannot scientifically measure the lighting damage. In this study, Fourier transform infrared spectroscopy was used as the evaluation method, and 10 kinds of narrow-band lights were used as the experimental light source to conduct a 1440 h irradiation experiment on the samples of the ancient Chinese Xuan paper. The oxidation index was calculated as the evaluation index based on the infrared spectra measured every 240 hours, and a mathematical model for the response rate of paper to spectrum and exposure was established. 610 spectra were obtained with the 10 kinds of narrow-band lights combined and superimposed. The color rendering indexes of the above spectra were calculated, and 9,477 spectra that meet the requirements of viewing indicators were obtained. By calculating the damage degree of the above spectra with the model, the optimal LED spectrum with the minimum damage which met the visual requirements was obtained. Then it was input into the 10-channel spectral simulation system for spectral restoration. Two kinds of lights commonly used in lighting for paper cultural relics were selected to conduct a comparative experiment. The results showed that the optimal LED spectrum reduced damage degree by 49.4% and 59.7% respectively compared with the two kinds of contrast light sources, and was beneficial to energy saving.