Search

SUMMARY Objectives: To analyze the effect of the porosity caused by incremental and bulk resin composite filling techniques using low- and high-viscosity composite resins on the biomechanical performance of root-treated molars. Methods: Forty intact molars received standardized mesio-occlusal-distal (MOD) cavity preparation, were root treated, and randomly divided into four groups with different filling techniques (n=10). The first involved two incremental filling techniques using VIT/Z350XT, a nanofilled composite resin (Filtek Z350XT, 3M ESPE) associated with a resin-modified glass ionomer cement, and resin-modified glass ionomer cement (RMGIC; Vitremer, 3M ESPE) for filling the pulp chamber. The second involved TPH/VIT, a microhybrid composite resin TPH3 Spectrum associated with Vitremer. The third and fourth involved two bulk-fill composite resins: SDR/TPH, a low-viscosity resin composite (Surefill SDR flow, Dentsply) associated with TPH3 Spectrum, and POST, a high-viscosity bulk-fill resin composite (Filtek Bulk Fill Posterior, 3M ESPE). The volume of the porosity inside the restoration was calculated by micro-CT. The cusp deformation caused by polymerization shrinkage was calculated using the strain-gauge and micro-CT methods. The cusp deformation was also calculated during 100 N occlusal loading and loading to fracture. The fracture resistance and fracture mode were recorded. Data were analyzed by one-way analysis of variance and Tukey test. The fracture mode was analyzed by the χ2 test. The volume of the porosity was correlated with the cusp deformation, fracture resistance, and fracture mode (a=0.05). Results: Incremental filling techniques associated with RMGIC resulted in a significantly higher porosity than that of both bulk-fill techniques. However, no significant difference was found among the groups for the fracture resistance, fracture mode, and cusp deformation, regardless of the measurement time and method used. No correlation was observed between the volume of the porosity and all tested parameters. Conclusions: The porosity of the restorations had no influence on the cuspal deformation, fracture resistance, or fracture mode. The use of the RMGIC for filling the pulp chamber associated with incremental composite resins resulted in similar biomechanical performance to that of the flowable or regular paste bulk-fill composite resin restorations of root-treated molars.

To describe a method of measuring the molar cusp deformation using micro-computed tomography (micro-CT), the propagation of enamel cracks using transillumination, and the effects of hygroscopic expansion after incremental and bulk-filling resin composite restorations.Twenty human molars received standardized Class II mesio-occlusal-distal cavity preparations. They were restored with either a bulk-fill resin composite, X-tra fil (XTRA), or a conventional resin composite, Filtek Z100 (Z100). The resin composites were tested for post-gel shrinkage using a strain gauge method. Cusp deformation (CD) was evaluated using the images obtained using a micro-CT protocol and using a strain-gauge method. Enamel cracks were detected using transillumination.The post-gel shrinkage of Z100 was higher than XTRA (P 0.001). The amount of cusp deformation produced using Z100 was higher compared to XTRA, irrespective of the measurement method used (P 0.001). The thinner lingual cusp always had a higher CD than the buccal cusp, irrespective of the measurement method (P 0.001). A positive correlation (r = 0.78) was found between cusp deformation measured by micro-CT or by the strain-gauge method. After hygroscopic expansion of the resin composite, the cusp displacement recovered around 85% (P 0.001). After restoration, Z100 produced more cracks than XTRA (P = 0.012).Micro-CT was an effective method for evaluating the cusp deformation. Transillumination was effective for detecting enamel cracks. There were fewer negative effects of polymerization shrinkage in bulk-fill resin restorations using XTRA than for the conventional incremental filling technique using conventional composite resin Z100.Shrinkage and cusp deformation are directly related to the formation of enamel cracks. Cusp deformation and crack propagation may increase the risk of tooth fracture.

The aim of this study was to evaluate the effect of magnification during post space preparation on root cleanness and on fiber post bond strength. Methods: Thirty human central upper incisors with similar root canal in size and shape were selected, decoronated to 15 mm and endodontically filled. The teeth were assigned into 3 groups (n=10), according to the method of magnification during post space preparation inspection: Control, using naked eye; loupe, using a dental surgical 3x magnifying glass; surgical microscope, using a 6x surgical microscope. The roots were scanned by using micro-CT before and after post space preparation for residue remnants evaluation. Fiber posts were cemented using self-adhesive resin cement (Rely X U200, 3M-ESPE). Two 1-mm-thick slices from the cervical, medium and apical thirds were submitted to a push-out test (PBS). Failures modes were classified. PBS data were analyzed by using two-way ANOVA with repeated measurement and the Tukey test. The significance level was set at 5%. The method of visualization had no effect on PBS (p=0.556). The cervical region had higher values than apical region irrespective of the inspection method (p=0.012). Adhesive failure between the resin cement and dentin was the prevalent failure mode for all groups. Micro-CT analysis showed no difference on root cleanness into the root canal after post space preparation. The use of magnification devices as loupe and microscope while performing post space do not improve the PBS and did not affect sealer remain of decoronated anterior teeth. Resumo Avaliar o efeito do método de visualização durante o preparo do espaço do pino sobre o remanescente de material obturador endodôntico e sobre a resistência adesiva do pino de fibra de vidro. Trinta incisivos centrais superiores humanos com canal radicular circular foram selecionados, foram desobstruídos a 15 mm e obturados. Os dentes foram divididos em 3 grupos (n=10), de acordo com o método de ampliação utilizado para inspeção do preparo: Controle, usando olho nu; lupa, usando uma lupa cirúrgica 3x cirúrgica; microscópio cirúrgico, usando um microscópio cirúrgico 6x. As raízes foram digitalizadas usando micro-CT antes e após a preparação do espaço para avaliação de resíduos remanescentes. Os pinos de fibra foram cimentados com cimento resinoso autoadesivo (RelyX U200, 3M-ESPE). Duas fatias de 1 mm de espessura dos terços cervical, médio e apical foram submetidas ao teste push-out (PBS). Os padrões de falhas foram classificados. Os dados de PBS foram analisados usando análise de variância em dois fatores com medição repetida e o teste de Tukey. O nível de significância foi estabelecido em 5%. Resultados: O método de visualização não teve efeito no PBS (p=0,556). A região cervical apresentou valores maiores que a região apical, independentemente do método de inspeção (p=0,012). A falha adesiva entre o cimento resinoso e a dentina foi o modo de falha prevalente para todos os grupos. A análise de micro-CT não mostrou diferença na limpeza da raiz no canal radicular após a preparação do espaço do pino. Conclusão: O uso de dispositivos de ampliação como lupas e microscópios durante a realização de preparo não melhora o PBS e não afetou a permanência do material obturador remanescente de dentes anteriores.

SUMMARY Objectives To evaluate the effect of the restorative protocol on cuspal strain, fracture resistance, residual stress, and mechanical properties of restorative materials in endodontically treated molars. Methods Forty-five molars received mesio-occlusal-distal (MOD) Class II preparations and endodontic treatment followed by direct restorations using three restorative protocols: composite resin (CR) only (Filtek Supreme, 3M-ESPE), resin modified glass ionomer cement in combination with CR (Vitremer, 3M-ESPE in pulp chamber and Filtek Supreme in MOD cavity), conventional glass ionomer cement in combination with composite resin (CGI-CR) (Ketac Fil, 3M-ESPE in pulp chamber and Filtek Supreme in MOD cavity). Cuspal strain was measured using strain gauges, and fracture resistance was tested with an occlusal load. Elastic modulus (EM) and Vickers hardness (VH) of the restorative materials were determined at different depths using dynamic microhardness indentation. Curing shrinkage was measured using the strain gauge technique. The restorative protocols were also simulated in finite element analysis (FEA). The shrinkage strain, cuspal strain, EM, VH, and fracture resistance data were statistically analyzed using split-plot analysis of variance and Tukey test (p=0.05). Residual shrinkage stresses were expressed in modified von Mises equivalent stresses. Results Shrinkage strain values (in volume %) were Ketac Fil (0.08±0.01) < Vitremer (0.18±0.01) < Filtek Supreme (0.54±0.03). Cuspal strain was higher and fracture resistance was lower when using CR only compared with the techniques that used glass ionomer. The EM and VH of the materials in the pulp chamber were significantly lower for glass ionomer. The FEA showed that using CR only resulted in higher residual stresses in enamel and root dentin close to the pulp chamber than the combinations with glass ionomers (RMGI-CR and CGI-CR). Conclusions The choice of restorative protocol significantly affected the biomechanical behavior of endodontically treated molars. Using glass ionomer to fill the pulp chamber is recommended when endodontically treated molars receive direct composite restorations because it reduces cuspal strain and increases fracture resistance.

The aim of this study was to evaluate the effect of porosity of self-adhesive resin on the stress distribution, post retention and failure mode of fiber post cemented to human root dentin. Ten human central upper incisors with circular root canal were selected. They were sectioned with 15 mm and were endodontically filled. The roots were scanned using micro-CT after post space preparation for root filling remaining evaluation. Fiber posts were cemented using self-adhesive resin cement (Rely X U200, 3M-ESPE). Two 1-mm-thick slices from the cervical, medium and apical thirds were scanned for resin cement bubbles volume measurements and submitted to a push-out test (PBS). Three operators using stereomicroscopy and confocal laser microscopy classified the failure mode. Stress distributions during the push-out test were analyzed using 3D finite element analysis. PBS values (MPa) were submitted to one-way ANOVA and Tukey's post hoc tests and the failure modes using the Kappa coefficient to assess inter-operator agreement. Chi-square test was used to determine significant differences between the methods ( = 0.05). Push-out bond strength was significantly affected by the bubbles presence in all root depth (p

SUMMARY Objectives This study tested the hypothesis that photoactivation timing and resin cement affect mechanical properties and bond strength of fiberglass posts to root dentin at different depths. Methods Fiberglass posts (Exacto, Angelus) were luted with RelyX Unicem (3M ESPE), Panavia F 2.0 (Kuraray), or RelyX ARC (3M ESPE) using three photoactivation timings: light curing immediately, after three minutes, or after five minutes. Push-out bonding strength, PBS (n=10) was measured on each root region (coronal, middle, apical). The elastic modulus (E) and Vickers hardness (VHN) of the cement layer along the root canal were determined using dynamic indentation (n=5). A strain-gauge test was used to measure post-gel shrinkage of each cement (n=10). Residual shrinkage stress was assessed with finite element analysis. Data were analyzed with two-way analysis of variance in a split-plot arrangement and a Tukey test (α=0.05). Multiple linear regression analysis was used to determine the influence of study factors. Results The five-minute delay photoactivation timing significantly increased the PBS for all resin cements evaluated. The PBS decreased significantly from coronal to apical root canal regions. The mean values for E and VHN increased significantly with the delayed photoactivation for RelyX Unicem and decreased from coronal to apical root regions for all resin cements with the immediate-curing timing. Conclusions The PBS of fiber posts to root dentin, E, and VHN values were affected by the root canal region, photoactivation timing, and resin cement type. Shrinkage stress values decreased gradually with delayed photoactivation for all the cements.

Objective This study aimed to evaluate the effect of the cavity preparation and ceramic type on the stress distribution, tooth strain, fracture resistance and fracture mode of human molar teeth restored with onlays. Material and Methods Forty-eight molars were divided into four groups (n=12) with assorted combinations of two study factors: BL- conventional onlay preparation with boxes made from leucite ceramic (IPS-Empress CAD, Ivoclar Vivadent); NBL- conservative onlay preparation without boxes made from leucite ceramic; BD- conventional onlay preparation with boxes made from lithium disilicate glass ceramic (IPS e.max CAD, Ivoclar Vivadent); NBL- conservative onlay preparation with boxes made from lithium disilicate glass ceramic cuspal deformation (µS) was measured at 100 N and at maximum fracture load using strain gauge. Fracture resistance (N) was measured using a compression test, and the fracture mode was recorded. Finite element analysis was used to evaluate the stress distribution by modified von Mises stress criteria. The tooth strain and fracture resistance data were analyzed using the Tukey test and two-way ANOVA, and the fracture mode was analyzed by the chi-square test (α=0.05). Results The leucite ceramic resulted in higher tooth deformation at 100 N and lower tooth deformation at the maximum fracture load than the lithium disilicate ceramic (P

SUMMARY Objectives: To compare radiopacity and porosity as expressed by the presence of voids in restorations carried out using bulk-fill and incremental filling techniques to restore large mesio-occlusal-distal (MOD) cavities. Methods: Fifty-five molars with MOD preparations were incrementally filled with Filtek Z-350XT (Z350XT) or bulk-fill composite: Filtek Bulk Fill/Z-350XT (FBF/Z350XT), Venus Bulk Fill/Charisma Diamond (VBF/CHA), SDR/Esthet-X HD (SDR/EST-X), Tetric EvoCeram Bulk Fill (TEC). Digital radiographic images (Vistascan scanner) were taken of restored molars and analyzed at the gingival and isthmus floors. Radiodensity measurements were performed using standardized points symmetrically distributed over each region of composite and tooth structure. Three calibrated evaluators visually assessed the presence of voids. Confidence intervals were calculated, and data were analyzed using analysis of variance and χ2 tests. Results: TEC and VBF/CHA showed significantly higher radiodensities, while the lowest values were observed for FBF/Z350XT and Z350XT. Radiodensity at the cervical regions tended to be greater than that found at the isthmus floor. The lowest incidence of voids was found for VBF/CHA, whereas the incremental insertion technique resulted in the highest rate of voids. Conclusion: Bulk-fill composite resin demonstrated an adequate level of radiodensity and a reduced presence of voids compared with the incremental filling technique.

SUMMARY Objectives: To evaluate the effect of flowable bulk-fill or conventional composite resin on bond strength and stress distribution in flat or mesio-occlusal-distal (MOD) cavity preparations using the microtensile bond strength (μTBS) test. Methods: Forty human molars were divided into two groups and received either standardized MOD or flat cavity preparations. Restorations were made using the conventional composite resin Z350 (Filtek Z350XT, 3M-ESPE, St Paul, MN, USA) or flowable bulk-fill (FBF) composite resin (Filtek Bulk Fill Flowable, 3M-ESPE). Postgel shrinkage was measured using the strain gauge technique (n=10). The Z350 buildup was made in two increments of 2.0 mm, and the FBF was made in a single increment of 4.0 mm. Six rectangular sticks were obtained for each tooth, and each section was used for μTBS testing at 1.0 mm/min. Polymerization shrinkage was modeled using postgel shrinkage data. The μTBS data were analyzed statistically using a two-way analysis of variance (ANOVA), and the postgel shrinkage data were analyzed using a one-way ANOVA with Tukey post hoc test. The failure modes were analyzed using a chi-square test (α=0.05). Results: Our results show that both the type of cavity preparation and the composite resin used affect the bond strength and stress distribution. The Z350 composite resin had a higher postgel shrinkage than the FBF composite resin. The μTBS of the MOD preparation was influenced by the type of composite resin used. Irrespective of composite resin, flat cavity preparations resulted in higher μTBS than MOD preparations (p Conclusions: FBF composite resin had lower shrinkage stress than Z350 conventional composite resin. The μTBS of the MOD preparation was influenced by the composite resin type. Flat cavity preparations had no influence on stress and μTBS. However, for MOD preparation, composite resin with higher shrinkage stress resulted in lower μTBS values.

SUMMARY Objectives: To analyze the effect of pulp-capping materials and resin composite light activation on strain and temperature development in the pulp and on the interfacial integrity at the pulpal floor/pulp-capping materials in large molar class II cavities. Methods: Forty extracted molars received large mesio-occlusal-distal (MOD) cavity bur preparation with 1.0 mm of dentin remaining at the pulp floor. Four pulp-capping materials (self-etching adhesive system, Clearfil SE Bond [CLE], Kuraray), two light-curing calcium hydroxide cements (BioCal [BIO], Biodinâmica, and Ultra-Blend Plus [ULT], Ultradent), and a resin-modified glass ionomer cement– (Vitrebond [VIT], 3M ESPE) were applied on the pulpal floor. The cavities were incrementally restored with resin composite (Filtek Z350 XT, 3M ESPE). Thermocouple (n=10) and strain gauge (n=10) were placed inside the pulp chamber in contact with the top of the pulpal floor to detect temperature changes and dentin strain during light curing of the pulp-capping materials and during resin composite restoration. Exotherm was calculated by subtracting postcure from polymerization temperature (n=10). Interface integrity at the pulpal floor was investigated using micro-CT (SkyScan 1272, Bruker). The degree of cure of capping materials was calculated using the Fourier transform infrared and attenuated total reflectance cell. Data were analyzed using one-way analysis of variance followed by the Tukey test (α=0.05). Results: Pulpal dentin strains (μs) during light curing of CLE were higher than for other pulp-capping materials (p Conclusions: Light curing of pulp-capping materials caused deformation of pulpal dentin and increased pulpal temperature in large MOD cavities. Shrinkage of the resin composite restoration caused debonding of BIO from the pulpal floor.

Objectives: To evaluate the effects of direct composite resin without a post or with one or two fiberglass posts on the restoration of severely compromised endodontically treated molars. Methods and Materials: Forty-five molars with 2 mm of “remaining tooth structure” were divided into three groups: Wfgp, restored with Filtek Z350XT without a fiberglass post; 1fgp, restored with Z350XT with one fiberglass post in the distal root canal; and 2fgp, restored with Z350XT with two fiberglass posts, one in the distal root canal and the other in the mesial-buccal root canal. The teeth were load cycled. Tooth remaining strain was measured using strain gauges (n=10) at two moments: TrSt-100 N, during 100 N occlusal loading, and TrSt-Fr, at fracture load. Fracture resistance was calculated, and fracture mode was classified. The elastic modulus and Vickers hardness were calculated using dynamic indentation (n=5). Stress distribution was analyzed by three-dimensional finite element analysis. Results: The use of two fiberglass posts resulted in lower fracture resistance than was noted in the groups with one fiberglass post and without fiberglass posts. The lingual surface of the remaining tooth had higher strain values than the buccal surface, regardless of the restorative technique and moment of evaluation. The absence of a fiberglass post resulted in significantly higher strain values and more irreparable fracture modes than were noted in the other groups. The use of one fiberglass post had a better strain/fracture resistance ratio. Stresses were concentrated in the occlusal portion of the post and in the furcation region. The presence of one fiberglass post resulted in better stress distribution in the entire distal root dentin, reducing stress on the critical areas. Conclusions: The use of one fiberglass post for restoring molars with direct composite resin resulted in higher fracture resistance than did the use of two fiberglass posts; it also resulted in better tooth remaining strain and stress distribution and more reparable fracture modes than were seen in the group without a fiberglass post.

SUMMARYNoncarious cervical lesions (NCCLs) are characterized by a loss of dental structure at the cementoenamel junction (CEJ) caused by stress, biocorrosion, and attrition. Variations in occlusal loading can promote different stress and strain patterns on the CEJ. Restoration of NCCLs is part of lesion management; however, there is still no conclusive restorative protocol for NCCLs. This study aimed to evaluate the stress and strain distribution of maxillary premolars with NCCLs according to three factors: 1) restorative technique; 2) direction of occlusal loading; and 3) mechanical fatigue. Three-dimensional (3D) finite element analysis (FEA) and strain gauge testing were used to assess stress and strain, respectively. 3D-FEA orthotropic, linear, and elastic models were generated: sound tooth (SO); unrestored NCCL; or NCCL restored with glass ionomer; flowable composite resin; nanofilled composite resin (CR); lithium disilicate ceramic; and nanofilled composite resin core associated with a lithium disilicate laminate (CL). A 150-N compressive static load was applied in two conditions: axially in both cusps (Al); and at a 45° angle to the long axis of the tooth applied to the palatine cusp (Ol). For the experimental tests, specimens were treated as described previously, and one strain gauge was attached to the buccal surface of each tooth to record tooth strains before and after cyclic loading (200,000 cycles, 50 N). FEA showed that the association of NCCL and Ol resulted in higher stress values. CR and CL restorations showed the closest biomechanical behavior to SO for both loading types. Loaded Al or Ol specimens showed higher strain values after mechanical fatigue. Lower stress and strain were observed with Al when compared with Ol. The restoration of NCCLs with composite resin only or associated with ceramic laminates seems to be the best approach because the results for those groups were similar in biomechanical behaviors to sound teeth.

SUMMARY Objectives To evaluate the effect of composite resins (one conventional and two low-shrink composites) and filling techniques on cuspal strains (CS), microtensile bond strength (μTBS), composite ultimate tensile strength (UTS), and mechanical properties of the composites at various depths in molars with large Class II restorations. Materials and Methods One hundred seventeen human molars received standardized Class II mesio-oclusal-distal cavity preparations and restorations with three composites (Filtek LS [3M-ESPE]; Aelite LS [BISCO]; and Filtek Supreme [3M-ESPE]) using three filling techniques (bulk, eight increments, and 16 increments). CS was measured using strain gauges, after which the same restored teeth were used to assess μTBS and UTS. The elastic modulus (E) and Vickers hardness (VH) at different depths were determined from microhardness indentations. The CS, μTBS, UTS, E, and VH data were statistically analyzed using split-plot analysis of variance and Tukey test (p=0.05). Results The CS was higher when using 16 increments. The ‘low-shrink' composites caused lower CS. The μTBS and UTS were similar for eight- and 16-increment techniques and higher when compared to the bulk filling in all composites. E and VH were constant through the depth when applied in eight or 16 increments. Conclusions Type of composite and filling technique affected the CS, μTBS, UTS, and mechanical properties of large Class II restorations. The eight-increments filling technique resulted in generally less CS with the same μTBS and UTS than was obtained with 16 increments, without affecting E and VH through the depth of the composites.

This study investigated the effects of endodontic treatment procedures and different post systems rehabilitation steps on the strain and temperature rise on apical and cervical root dentin regions. Twenty-one extracted human canine teeth had two strain gages attached to the distal root surface and two thermocouples attached to the mesial root surface (cervical and apical). The strain and temperature rise were recorded during the following procedures: root canal preparation, final rinse and drying, root canal filling and canal relief. Then the teeth were divided into three groups (n=7), according to the type of post system: CPC, cast post and core; FGP, fiberglass post; and PSP, prefabricated steel post. Data continued to be recorded during the post space preparation, post modeling (only for CPC), post trying and post cementation. Data were subjected to a two-way ANOVA followed by Tukey's test (α=0.05). The post-space preparation caused the highest temperature rise (4.0-14.9 °C) and the highest strain in the apical region during irrespective of post type. The resin cement light-activation resulted in significant temperature increases in the cervical region for all of the groups. The canal relief and the post-space preparation produced highest temperature rises. The CPC post modeling resulted in higher root strain level similarly the level of post preparation. The PSP resulted in highest strain during post trying and post cementation. Este estudo investigou os efeitos de diferentes etapas do tratamento endodôntico e da inserção de diferentes tipos de retentores na deformação e aumento de temperatura na dentina radicular apical e cervical. Vinte e um dentes caninos humanos extraídos tiveram dois extensômetros colados à superfície da raiz distal e dois termopares ligados à superfície da raiz mesial (cervical e apical). A deformação e aumento de temperatura foram registrados durante os seguintes procedimentos: preparo do canal radicular, irrigação final e secagem, obturação do canal, alívio do canal; em seguida, os dentes foram divididos em três grupos (CPC, núcleo moldado e fundido; FGP, pino de fibra de vidro, e PSP pino pré-fabricado em aço-inoxidável, n=7). Os dados foram continuamente mensurados durante a modelagem do núcleo (somente para o CPC), inserção e cimentação dos retentores. Os dados foram submetidos a análise de variância fatorial, seguido pelo teste de Tukey (α=0,05). O preparo do canal para o retentor causou o maior aumento de temperatura (4,0-14,9 °C) e maior deformação na região apical independente do tipo de retentor. A ativação com luz resultou em significativo aumento de temperatura na região cervical, para todos os grupos. O alívio do canal e o preparo para o pino produziram maiores aumentos de temperatura. A modelagem do CPC resultou em maior nível de deformação da raiz em nível similar ao preparo para o retentor. O PSP resultou em maior deformação durante a inserção e ao final da cimentação.

SUMMARY Objective: The aim of this study was to investigate the effect of delayed photo-activation on elastic modulus, Knoop hardness, and post-gel shrinkage of dual cure resin cements and how this affects residual shrinkage stresses in posterior teeth restored with ceramic inlays. Methods and Materials: Four self-adhesive (RelyX Unicem, 3M ESPE; GCem, GC; MonoCem, Shofu; and seT, SDI) and two conventional (RelyX ARC, 3M ESPE; and AllCem, FGM) dual cure resin cements for cementing posterior ceramic inlays were tested. Strain gauge and indentation tests were used to measure the post-gel shrinkage (Shr), elastic modulus (E), and Knoop hardness (KHN) when photo-activated immediately and 3 and 5 minutes after placement (n=10). Shr, E, and KHN results were analyzed using two-way analysis of variance followed by Tukey honestly significant difference post hoc tests (α=0.05). The experimentally determined properties were applied in a finite element analysis of a leucite ceramic inlay (Empress CAD, Ivoclar Vivadent) cemented in a premolar. Modified von Mises stresses were evaluated at the occlusal margins and cavity floor. Results: Shr, E, and KHN varied significantly among the resin cements (p Conclusions: KHN and E values varied among the different resin cements. Residual shrinkage stress levels decreased with increasing photo-activation delay with all resin cements.

Objectives To compare bulk-fill with incremental filling techniques for restoring large mesio-occlusal-distal (MOD) restorations. Methods Seventy-five molars with MOD preparations were divided into five groups: Z350XT, incrementally filled with Filtek Z350XT and four bulk-fills—FBF/Z350XT, Filtek Bulk Fill/Filtek Z350XT; VBF/CHA, Venus Bulk Fill/Charisma Diamond; SDR/EST-X, SDR/Esthet-X HD; TEC, TetricEvoCeram Bulk Fill. Cuspal strains were measured using strain-gauges ( n = 10): CSt-Re, during restorative procedure; CSt-100N, during 100N occlusal loading; CSt-Fr, at fracture load. Before fracture load, teeth were load-cycled. Fracture resistance, fracture mode, and enamel cracks were recorded. The other five teeth were used for Elastic modulus (E) and Vickers hardness (VH). Post-gel shrinkage (Shr), diametral tensile strength (DTS) and compressive strength (CS) were determined ( n = 10). Shrinkage stresses were analyzed using finite element analysis. Results SDR had similar CS values as TEC, lower than all other composites. CHA had similar DTS values as Z350XT, higher than all other composites. Z350XT had the highest mean Shr and SDR the lowest Shr. New enamel cracks and propagation was observed after the restoration, regardless of filling technique. Z350XT had lower fracture resistance than bulk-fill composite techniques. No significant differences in failure modes were found. E and VH were constant through the depth for all techniques. Bulk-filling techniques had lower stresses compared to Z350XT. Conclusions Flowable bulk-fill composites had lower mechanical properties than paste bulk-fill and conventional composites. All bulk-fill composites had lower post-gel shrinkage than conventional composite. Bulk-fill filling techniques resulted in lower cusp strain, shrinkage stress and higher fracture resistance. Clinical significance Using bulk-fill composites cause lower CSt wich indicates lower stress in restored tooth. Furthermore, bulk-fill composites have a higher fracture resistance. Therefore, clinicians may choose the bulk-fill composite to decrease undesirable effects of restoration while simplifying filling procedure.

SUMMARY Objectives Finite element analysis (FEA) was used to study polymerization shrinkage stress in molars restored with composites and to correlate those stresses with experimentally measured tooth deformation. Methods Three composites (Filtek LS, Aelite LS Posterior, Filtek Supreme) and three filling techniques (bulk, 2.0-mm increments, and 1.0-mm increments) for restoring a molar were simulated in a two-dimensional FEA. Polymerization shrinkage was modeled using post-gel shrinkage, which was measured using the strain gauge technique (n=10). Cuspal tooth deformation, measured at the buccal and lingual surfaces with strain gauges in a laboratory study, was used to validate the analysis. Residual shrinkage stresses were expressed in modified von Mises equivalent stresses. Linear Pearson correlations were determined between the laboratory and FEA results. Results Post-gel shrinkage values (in volume %) were: Filtek LS (0.11 ± 0.03) < Aelite LS Posterior (0.51 ± 0.02) < Filtek Supreme (0.62 ± 0.09). The 1.0-mm increment filling caused substantially higher stresses and strains in the cervical enamel region. Significant correlations were found between: elastic modulus and FEA strain, elastic modulus and FEA stress, post-gel shrinkage and FEA strain, post-gel shrinkage and FEA stress, FEA strain and cuspal deformation by strain gauge, and FEA stress and cuspal deformation by strain gauge (p Conclusions Increasing the number of increments and high post-gel shrinkage and/or elastic modulus values caused higher stresses in the remaining tooth structure and tooth/restoration interface. Cuspal deformation measured with the strain gauge method validated the finite element analyses.

Objective to correlate polymerization stress data obtained under two compliance conditions with those from different interfacial quality tests. Methods Six commercial composites were tested (Filtek Z250/3M ESPE, Heliomolar/Ivoclar Vivadent, Aelite LS Posterior/Bisco, Filtek Supreme/3M ESPE, ELS/Saremco and Venus Diamond/Heraeus Kulzer). Bond strength (BS) was evaluated by push-out test on slices of bovine dentin (2-mm thick) with tapered cavities. For microleakage (ML) and gap analysis, cylindrical cavities in bovine incisors (4-mm diameter and 1.5-mm height) were restored and epoxy replicas of the cavo-surface margins were prepared for analysis under scanning electron microscopy (200×). The same specimens were submitted to a microleakage protocol using AgNO 3 as tracer. After sectioned twice perpendicularly, ML was determined under a stereomicroscope (60×). Polymerization stress (PS, n = 5) was determined by the insertion of the composite ( h = 1.5 mm) between poly(methyl methacrylate), PMMA, or glass rods (O = 4 mm) attached to a universal testing machine. Data were analyzed using Kruskal–Wallis (ML and gaps), and ANOVA/Tukey (BS and PS, α = 5%). Pearson's correlation test was used to verify correlations between stress and interfacial quality. Results BS varied from 4.7 to 7.9 MPa. Average ML data ranged from 0.34 to 0.89 mm. Maximum ML varied from 0.61 to 1.34 mm. Gap incidence varied from 13 to 47%. PS ranged from 2.5 to 4.4 MPa in PMMA, and between 2.1 and 8.2 in glass. Statistically significant correlations were observed between stress and interfacial quality, except between BS and PS in glass. These correlations were stronger when PMMA was used as bonding substrate. Conclusions PS data obtained using a high compliance testing system showed a stronger correlation with “in vitro” interfacial integrity results, compared to data from a low compliance system.

Purpose: This study evaluated the bond strength of adhesive luting agents applied to caries-affected dentin (CAD). Methods and materials: Thirty-six non-carious human third molars were abraded to expose an occlusal dentin surface. Caries lesions were induced in half of the samples using a microcosm biofilm model. Biofilm was cultivated under an anaerobic atmosphere for 14 days in a medium enriched with mucin. The same medium containing 1% sucrose was alternated for 4h per day. Cylinders of resin cement (RelyX ARC, RelyX U200 or BisCem) were built up over the dentin substrate and submitted to shear bond load. The samples were then longitudinally sectioned. The hardness and elastic modulus of dentin was measured at depths of 10, 20, 30, 40, 50, 100, 150 and 200 m from the occlusal surface. A three-dimensional finite element simulation was performed to analyze the residual stress distribution for each experimental condition during the shear bond strength test. Bond strength data were analyzed by two-way ANOVA and hardness and elastic modulus by split-plot ANOVA. Multiple comparisons were performed with the Student–Newman–Keuls test (a=0.05). Results: Independent of the type of cement, the highest bond strengths were observed in sound dentin. Relyx ARC bond strength was similar to that of RelyX U200 for both substrates; BisCem had the lowest values. CAD had lower hardness values than sound dentin above a depth of 100 m. Elasticmodulus exhibited a similar trend, but above a depth of 150 m. Stress distribution during the bond strength test was similar under all experimental conditions. Conclusion: Impairment of the mechanical properties of dentin promoted by carious lesions reduced the bond strength of adhesive luting agents.