Search

The conversion of naturally abundant nitrogen into ammonia in a sustainable way at room temperature would be an ideal alternative to the currently dominant Haber–Bosch process. However, the rational design and synthesis of efficient and stable noble-metal-free electrocatalysts for the nitrogen reduction reaction (NRR) still represents a major challenge. Herein, novel Cu2SnS3 nanocrystals with a uniform nanostructure were prepared through a hydrothermal approach by tuning the heating time. Electrochemical measurements demonstrated that Cu2SnS3 synthesized by heating at 200 °C for 10 h achieved a faradaic efficiency for the NRR of 8.87 % and a NH3 yield of 8.22 μg h−1 mg cat−1 at −0.4 V in 0.1 M Na2SO4. These results suggest a feasible new route toward the rational design of NRR catalysts with high stability and selectivity for use in clean energy conversion.

The CCCH zinc-finger protein contains a typical C3H-type motif widely existing in plants, and it plays an important role in plant growth, development, and stress responses. In this study, a CCCH zinc-finger gene, GhC3H20, was isolated and thoroughly characterized to regulate salt stress in cotton and Arabidopsis. The expression of GhC3H20 was up-regulated under salt, drought, and ABA treatments. GUS activity was detected in the root, stem, leaves, and flowers of ProGhC3H20::GUS transgenic Arabidopsis. Compared with the control, the GUS activity of ProGhC3H20::GUS transgenic Arabidopsis seedlings under NaCl treatment was stronger. Through the genetic transformation of Arabidopsis, three transgenic lines of 35S-GhC3H20 were obtained. Under NaCl and mannitol treatments, the roots of the transgenic lines were significantly longer than those of the wild-type (WT) Arabidopsis. The leaves of the WT turned yellow and wilted under high-concentration salt treatment at the seedling stage, while the leaves of the transgenic Arabidopsis lines did not. Further investigation showed that compared with the WT, the content of catalase (CAT) in the leaves of the transgenic lines was significantly higher. Therefore, compared with the WT, overexpression of GhC3H20 enhanced the salt stress tolerance of transgenic Arabidopsis. A virus-induced gene silencing (VIGS) experiment showed that compared with the control, the leaves of pYL156-GhC3H20 plants were wilted and dehydrated. The content of chlorophyll in pYL156-GhC3H20 leaves was significantly lower than those of the control. Therefore, silencing of GhC3H20 reduced salt stress tolerance in cotton. Two interacting proteins (GhPP2CA and GhHAB1) of GhC3H20 have been identified through a yeast two-hybrid assay. The expression levels of PP2CA and HAB1 in transgenic Arabidopsis were higher than those in the WT, and pYL156-GhC3H20 had expression levels lower than those in the control. GhPP2CA and GhHAB1 are the key genes involved in the ABA signaling pathway. Taken together, our findings demonstrate that GhC3H20 may interact with GhPP2CA and GhHAB1 to participate in the ABA signaling pathway to enhance salt stress tolerance in cotton.

As the basic raw material of bio-oil based eco-friendly lubricant, a special selected by-product vegetable acidified oil (AO) was modified by vulcanization, esterification, or vulcanization followed by esterification. The optimized vulcanization process conditions are 1% sulfur powder catalyzed, temperature 130 ℃, reaction time 2 h, while the optimized esterification process requires 20% glycerol and 1% H2SO4 catalysis, reaction temperature 220 ℃, reaction time 3 h. We compounded modified AO, diluent, pour point depressant and emulsifier into an advanced drilling lubricant F-1. F-1 has excellent performances in bentonite drilling fluids, the extreme pressure lubrication coefficient reduction rate (Δf) in fresh water mud is 86.84%, and 85.76% in 4% NaCl salt water mud. After aging at 150 ℃ for 16 h, its Δf is improved compared with room temperature. Adding F-1 to the basic bentonite mud system, the filtration loss of drilling fluids decreased from 10 mL to 6.5 mL, the apparent viscosity and plastic viscosity experienced little change before and after aging. The new bio-oil compound lubricant has an excellent temperature resistance, a high salt contamination resistance and cost-effective. Vulcanization and esterification processes help to improve the lubricity and reduce foaming rates.

Summary: Mixed-matrix membranes (MMMs) comprising polymer matrices and metal-organic frameworks (MOFs) provide efficient and economic CO2 separation. One major challenge is to construct continuous and defect-free MMMs due to poor MOF/polymer compatibility. Here, this protocol describes the step-by-step details for synthesis of desired linkers that allow the fabrication of new polymerizable MOFs containing vinyl groups (BUCT MOFs) and the preparation procedures of defect-free MMMs with enhanced MOF/polymer interfacial adhesion and boosted gas separation performances.For complete details on the use and execution of this profile, please refer to Chen et al. (2021).

A technique of covalent bonding of grafted polymer brushes of poly(poly(ethylene glycol) monomethacrylate) (P(PEGMA)) on the surface of silicon quantum dots (SiQDs) and activation of the end hydroxyls with N-hydroxysuccinimide (NHS) esters were described in this work in detail. Firstly, a Si/SiQDs slice was disposed with hydrofluoric acid solution to produce surface Si-Hx (x = 1, 2 or 3) species, which combined with vinyl group of 1-undecenol covalently gives terminal hydroxyls. Such hydroxyls were initialized and were involved in atom transfer radical polymerization to construct grafted polymer brushes of P(PEGMA). Hence the density of the surface hydroxyls was enhanced extremely on account of the end hydroxyls of the side chains of the polymer brushes. Then carboxyl groups were introduced via terminal esterification with succinic anhydride, which were activated subsequently with NHS giving NHS esters under rather mild conditions. The reactivity of the terminal NHS esters was demonstrated by SDS-PAGE gel electrophoresis and fluorescence imaging. The SiQDs were demonstrated by transmission electron microscopy. The stepwise modifications on SiQDs were characterized by infrared and X-ray photoelectron spectra. The photoluminescence of the SiQDs was remained during the chemical modifications, proved by the measurements of fluorescence spectra. Keywords: Silicon quantum dots, Grafted polymer brushes, Poly(poly(ethylene glycol) monomethacrylate), N-hydroxysuccinimide esters

Soil salinization conditions seriously restrict cotton yield and quality. Related studies have shown that the DUF4228 proteins are pivotal in plant resistance to abiotic stress. However, there has been no systematic identification and analysis of the DUF4228 gene family in cotton and their role in abiotic stress. In this study, a total of 308 DUF4228 genes were identified in four Gossypium species, which were divided into five subfamilies. Gene structure and protein motifs analysis showed that the GhDUF4228 proteins were conserved in each subfamily. In addition, whole genome duplication (WGD) events and allopolyploidization might play an essential role in the expansion of the DUF4228 genes. Besides, many stress-responsive (MYB, MYC) and hormone-responsive (ABA, MeJA) related cis-elements were detected in the promoters of the DUF4228 genes. The qRT-PCR results showed that GhDUF4228 genes might be involved in the response to abiotic stress. VIGS assays and the measurement of relative water content (RWC), Proline content, POD activity, and malondialdehyde (MDA) content indicated that GhDUF4228-67 might be a positive regulator of cotton response to salt stress. The results in this study systematically characterized the DUF4228s in Gossypium species and will provide helpful information to further research the role of DUF4228s in salt tolerance.

Converting carbon dioxide into high-value-added formic acid as a basic raw material for the chemical industry via an electrochemical process under ambient conditions not only alleviates greenhouse gas effects but also contributes to effective carbon cycles. Unfortunately, the most commonly used Pd-based catalysts can be easily poisoned by the in situ formed minor byproduct CO during the carbon dioxide reduction reaction (CRR) process. Herein, we report a facile method to synthesize highly uniformed PdAg alloys with tunable morphologies and electrocatalytic performance via a simple liquid synthesis approach. By tuning the molar ratio of the Ag+ and Pd2+ precursors, the morphologies, composition, and electrocatalytic activities of the obtained materials were well-regulated, which was characterized by TEM, XPS, XRD, as well as electrocatalytic measurements. The CRR results showed that the as-obtained Pd3Ag exhibited the highest performance among the five samples, with a faradic efficient (FE) of 96% for formic acid at −0.2 V (vs. reference hydrogen electrode (RHE)) and superior stability without current density decrease. The enhanced ability to adsorb and activate CO2 molecules, higher resistance to CO, and a faster electronic transfer speed resulting from the alloyed PdAg nanostructure worked together to make great contributions to the improvement of the CRR performance. These findings may provide a new feasible route toward the rational design and synthesis of alloy catalysts with high stability and selectivity for clean energy storage and conversion in the future.

Abiotic stress, such as drought and salinity stress, seriously inhibit the growth and development of plants. Therefore, it is vital to understand the drought and salinity resistance mechanisms to enable cotton to provide more production under drought and salt conditions. In this study, we identified 8806 and 9108 differentially expressed genes (DEGs) through a comprehensive analysis of transcriptomic data related to the PEG-induced osmotic and salt stress in cotton. By performing weighted gene co-expression network analysis (WGCNA), we identified four co-expression modules in PEG treatment and five co-expression modules in salinity stress, which included 346 and 324 predicted transcription factors (TFs) in these modules, respectively. Correspondingly, whole genome duplication (WGD) events mainly contribute to the expansion of those TFs. Kyoto Encyclopedia of Genes and Genomes (KEGG) and gene ontology (GO) analyses revealed those different modules were associated with stress resistance, including regulating macromolecule metabolic process, peptidase activity, transporter activity, lipid metabolic process, and responses to stimulus. Quantitative RT-PCR analysis was used to confirm the expression levels of 15 hub TFs in PEG6000 and salinity treatments. We found that the hub gene GhWRKY46 could alter salt and PEG-induced drought resistance in cotton through the virus-induced gene silencing (VIGS) method. Our results provide a preliminary framework for further investigation of the cotton response to salt and drought stress, which is significant to breeding salt- and drought-tolerant cotton varieties.

As the only renewable organic carbon source, abundant biomass has long been established and developed to mass-produce functionalized carbon materials. Herein, an extremely facile and green strategy was executed for the first time to in situ construct K-Fe3C@C nanohybrids directly by one-pot carbonizing the pomelo peel impregnated with Fe(NO3)3 solutions. The pyrolytically self-assembled nanohybrids were successfully applied in Fischer–Tropsch synthesis (FTS) and demonstrated high catalytic performance. Accordingly, the optimized K-Fe3C@C catalysts revealed excellent FTS activity (92.6% CO conversion) with highlighted C5+ hydrocarbon selectivity of 61.3% and light olefin (C2-4=) selectivity of 26.0% (olefin/paraffin (O/P) ratio of 6.2). Characterization results further manifest that the high performance was correlated with the in situ formation of the core-shell nanostructure consisting of Fe3C nanoparticles enwrapped by graphitized carbon shells and the intrinsic potassium promoter originated in pomelo peel during high-temperature carbonization. This work provided a facile approach for the low-cost mass-fabrication of high-performance FTS catalysts directly utilizing waste biomass without any chemical pre-treatment or purification.

As one of the most important factors in alternative splicing (AS) events, serine/arginine-rich (SR) proteins not only participate in the growth and development of plants but also play pivotal roles in abiotic stresses. However, the research about SR proteins in cotton is still lacking. In this study, we performed an extensive comparative analysis of SR proteins and determined their phylogeny in the plant lineage. A total of 169 SR family members were identified from four Gossypium species, and these genes could be divided into eight distinct subfamilies. The domain, motif distribution and gene structure of cotton SR proteins are conserved within each subfamily. The expansion of SR genes is mainly contributed by WGD and allopolyploidization events in cotton. The selection pressure analysis showed that all the paralogous gene pairs were under purifying selection pressure. Many cis-elements responding to abiotic stress and phytohormones were identified in the upstream sequences of the GhSR genes. Expression profiling suggested that some GhSR genes may involve in the pathways of plant resistance to abiotic stresses. The WGCNA analysis showed that GhSCL-8 co-expressed with many abiotic responding related genes in a salt-responding network. The Y2H assays showed that GhSCL-8 could interact with GhSRs in other subfamilies. The subcellular location analysis showed that GhSCL-8 is expressed in the nucleus. The further VIGS assays showed that the silencing of GhSCL-8 could decrease salt tolerance in cotton. These results expand our knowledge of the evolution of the SR gene family in plants, and they will also contribute to the elucidation of the biological functions of SR genes in the future.

High-performance temperature sensing is a key technique in modern Internet of Things. However, it is hard to attain a high precision while achieving a compact size for wireless sensing. Recently, metamaterials have been proposed to design a microwave, wireless temperature sensor, but precision is still an unsolved problem. By combining the high-quality factor (Q-factor) feature of a EIT-like metamaterial unit and the large temperature-sensing sensitivity performance of liquid metals, this paper designs and experimentally investigates an Hg-EIT-like metamaterial unit block for high figure-of-merit (FOM) temperature-sensing applications. A measured FOM of about 0.68 is realized, which is larger than most of the reported metamaterial-inspired temperature sensors.

Plant press slag (PPS) containing abundant cellulose and starch is a byproduct in the deep processing of fruits, cereals, and tuberous crops products. PPS can be modified by using caustic soda and chloroacetic acid to obtain an inexpensive and environmentally friendly filtrate reducer of drilling fluids. The optimum mass ratio of mNaOH:mMCA:mPPS is 1:1:2, the optimum etherification temperature is 75 °C, and the obtained product is a natural mixture of carboxymethyl cellulose and carboxymethyl starch (CMCS). PPS and CMCS are characterized by using X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric, X-ray photoelectron spectroscopy, and elemental analysis. The filtration loss performance of CMCS is stable before and after hot-rolling aging at 120 °C in 4.00% NaCl and saturated NaCl brine base slurry. The minimum filtration loss value of CMCS is 5.28 mL/30 min at the dosage of 1.50%. Compared with the commercial filtrate reducers with a single component, i.e., carboxymethyl starch (CMS) and low viscosity sodium carboxymethyl cellulose (LV-CMC), CMCS have a better tolerance to high temperature of 120 °C and high concentration of NaCl. The filtration loss performance of low-cost CMCS can reach the standards of LV-CMC and CMS of the specification of water-based drilling fluid materials in petroleum industry.

Dental mold gypsum materials require fine powder, appropriate liquidity, fast curing, and easy-to-perform clinical operations. They require low linear expansion coefficient and high strength, reflecting the master model and facilitating demolding. In this article, the suitable accelerators and reinforcing agents were selected as additives to modify dental gypsum. The main experimental methods used were to compare the trends of linear expansion coefficients of several commercially available dental gypsum products over 72 h and to observe the cross-sectional microstructure of cured bodies before and after dental gypsum modification using scanning electron microscopy. By adjusting the application of additives, the linear expansion coefficient of dental gypsum decreased from 0.26% to 0.06%, while the flexural strength increased from 6.7 MPa to 7.4 MPa at 2 h. Formulated samples showed good stability and gelation properties with linear expansion completed within 12 h. It is indicated that the performance of dental gypsum materials can be improved by adding additives and nanomaterials, which provided a good reference for clinical preparation of high-precision dental prosthesis.

Flower-like metallic nanocrystals have shown great potential in the fields of nanophononics and energy conversion owing to their unique optical properties and particular structures. Herein, colloid Au nanoflowers with different numbers of petals were prepared by a steerable template process. The structure-adjustable Au nanoflowers possessed double plasmon resonances, tunable electric fields, and greatly enhanced SERS and photocatalytic activity. In the extinction spectra, Au nanoflowers had a strong electric dipole resonance located around 530 to 550 nm. Meanwhile, a longitudinal plasmon resonance (730~760 nm) was obtained when the number of petals of Au nanoflowers increased to two or more. Numerical simulations verified that the strong electric fields of Au nanoflowers were located at the interface between the Au nanosphere and Au nanopetals, caused by the strong plasmon coupling. They could be further tuned by adding more Au nanopetals. Meanwhile, much stronger electric fields of Au nanoflowers with two or more petals were identified under longitudinal plasmon excitation. With these characteristics, Au nanoflowers showed excellent SERS and photocatalytic performances, which were highly dependent on the number of petals. Four-petal Au nanoflowers possessed the highest SERS activity on detecting Rhodamine B (excited both at 532 and 785 nm) and the strongest photocatalytic activity toward photodegrading methylene blue under visible light irradiation, caused by the strong multi-interfacial plasmon coupling and longitudinal plasmon resonance.

As a promising energy storage system, potassium (K) ion batteries (KIBs) have received extensive attention due to the abundance of potassium resource in the Earth’s crust and the similar properties of K to Li. However, the electrode always presents poor stability for K-ion storage due to the large radius of K-ions. In our work, we develop a nitrogen-doped carbon nanofiber (N-CNF) derived from bacterial cellulose by a simple pyrolysis process, which allows ultra-stable K-ion storage. Even at a large current density of 1 A g−1, our electrode exhibits a reversible specific capacity of 81 mAh g−1 after 3000 cycles for KIBs, with a capacity retention ratio of 71%. To investigate the electrochemical enhancement performance of our N-CNF, we provide the calculation results according to density functional theory, demonstrating that nitrogen doping in carbon is in favor of the K-ion adsorption during the potassiation process. This behavior will contribute to the enhancement of electrochemical performance for KIBs. In addition, our electrode exhibits a low voltage plateau during the potassiation–depotassiation process. To further evaluate this performance, we calculate the “relative energy density” for comparison. The results illustrate that our electrode presents a high “relative energy density”, indicating that our N-CNF is a promising anode material for KIBs.

Gibberella stalk rot (GSR) by Fusarium graminearum causes significant losses of maize production worldwide. Jasmonates (JAs) have been broadly known in regulating defense against pathogens through the homeostasis of active JAs and COI-JAZ-MYC function module. However, the functions of different molecular species of JAs and COI-JAZ-MYC module in maize interactions with Fusarium graminearum and regulation of diverse metabolites remain unknown. In this study, we found that exogenous application of MeJA strongly enhanced resistance to GSR. RNA-seq analysis showed that MeJA activated multiple genes in JA pathways, which prompted us to perform a genome-wide screening of key JA signaling components in maize. Yeast Two-Hybrid, Split-Luciferase, and Pull-down assays revealed that the JA functional and structural mimic coronatine (COR) functions as an essential ligand to trigger the interaction between ZmCOIa and ZmJAZ15. By deploying CRISPR-cas9 knockout and Mutator insertional mutants, we demonstrated that coi1a mutant is more resistant, whereas jaz15 mutant is more susceptible to GSR. Moreover, JA-deficient opr7-5opr8-2 mutant displayed enhanced resistance to GSR compared to wild type. Together, these results provide strong evidence that ZmJAZ15 plays a pivotal role, whereas ZmCOIa and endogenous JA itself might function as susceptibility factors, in maize immunity to GSR.

Verticillium wilt will seriously affect cotton yield and fiber quality. BEL1-Like transcription factors are involved in the regulation of secondary cell wall (SCW) formation, especially the biosynthesis of lignin that also plays a key role in cotton disease resistance. However, there is no report on the role of BEL1-Like transcription factor in the regulation of plant biological stress. In this study, tissue expression pattern analysis showed that a BEL1-Like transcription factor GhBLH7-D06 was predominantly expressed in vascular tissues and the SCW thickening stage of fiber development, while its expression could also respond to Verticillium dahliae infection and the phytohormone MeJA treatment, which indicated that GhBLH7-D06 might be involved in the defense response of Verticillium wilt. Using virus-induced gene silencing (VIGS) technology, we found silencing the expression of GhBLH7-D06 could enhance the resistance of cotton plants to Verticillium wilt, and the acquisition of resistance might be mainly due to the significant overexpression of genes related to lignin biosynthesis and JA signaling pathway, which also proves that GhBLH7-D06 negatively regulates the resistance of cotton to Verticillium wilt. Based on the results of yeast two-hybrid (Y2H) library screening and confirmation by bimolecular fluorescence complementary (BiFC) experiment, we found an Ovate Family Protein (OFP) transcription factor GhOFP3-D13 which was also a negative regulator of cotton Verticillium wilt resistance could that interacts with GhBLH7-D06. Furthermore, the dual-luciferase reporter assay and yeast one-hybrid (Y1H) experiment indicated that GhBLH7-D06 could target binding to the promoter region of GhPAL-A06 to suppress its expression and eventually lead to the inhibition of lignin biosynthesis. In general, the GhBLH7-D06/GhOFP3-D13 complex can negatively regulate resistance to Verticillium wilt of cotton by inhibiting lignin biosynthesis and JA signaling pathway.

This paper addresses the problem of voltage restoration and reactive power sharing of inverter-based distributed generations (DGs) in an islanded microgrid subject to denial-of-service (DoS) attacks. Note that DoS attacks may block information exchange among DGs by jamming the communication network in the secondary control level of a microgrid. A two-layer distributed secondary control framework is presented, in which a state observer employing the multiagent system (MAS)-based ternary self-triggered control is implemented for discovering the average information of voltage and reactive power in a fully distributed manner while highly reducing communication burden than that the periodic communication way. The compensation for the reference signal to the primary control is acquired according to the average estimates to achieve voltage restoration while properly sharing reactive power among DGs. An improved ternary self-triggered control strategy integrating an acknowledgment (ACK)-based monitoring mechanism is established, where DoS attacks are modeled by repeated cycles of jamming and sleeping. A new triggering condition is developed to guarantee the successful information exchange between DGs when the sleep period of DoS attacks is detected. Using the Lyapunov approach, it is proved that the proposed algorithm allows agents to reach consensus regardless of the frequency of the DoS attacks, which maintains the accurate estimation of average information and the implementation of the secondary control objectives. The performance of the proposed control scheme is evaluated under simulation and experimental conditions. The results show that the proposed secondary control scheme can highly reduce the inter-agent communication as well as improve the robustness of the system to resist DoS attacks.

Plasmonic Au-ZnO hybrids with adjustable structures (including Au-decorated ZnO and core–shell Au@ZnO with dense and porous ZnO shells) and the optimized hot electron-driven photocatalytic activity were successfully prepared. It was found that the Au@ZnO core–shell hybrids with porous morphology had the highest plasmon-enhanced photocatalytic hydrogen generation activity under visible light irradiation. The wavelength-dependent photocatalytic tests verified that Au@ZnO with porous ZnO shells had the highest apparent quantum efficiency upon resonance excitation. The ultrafast transient absorption measurements revealed that Au@ZnO with porous ZnO shells had the fastest plasmon-induced hot electron injection, which was thought to be the reason for the improved photocatalytic activity. This work might provide a promising route to designing photocatalytic and photoelectric materials.

As an important part of the turbomachinery, the rotor–bearing system has been upgraded to provide a high rotating speed in order to meet the demand of high power production. With increasing demand for stability, the squeeze film damper (SFD) has been widely used in industrial machinery because it can reduce the vibration amplitude and suppress the external force. Usually, it shows inadaptability under the different working conditions where the SFD parameters didn’t change appropriately. Therefore, the reasonable choice of operational parameters of SFD is the key solution that can provide viscous damping effectively and restrain the nonlinear vibration generated by faults. In this paper, the mathematical model of a rotor-ball bearing-SFD system considering the misalignment fault and misalignment-rubbing coupling fault is built first. Then the dynamic characteristics under typical working conditions (ω = 1000 rad/s) of the faulted rotor are discussed. The vibration attenuation effects of the SFD parameters selected by using the multi-objective optimization method on the dynamic responses are analyzed. The results show that when the rotor system operates under different states, the value and the sensitivity of optimization parameters are altered. With no fault, the amplitude of fundamental frequency decrease 23%. With the misalignment fault, the amplitude of the fundamental frequency decreases by 43.4%, the amplitude of 2× fundamental frequency decreases by 27.5%, and the amplitude of 3× fundamental frequency decreases by 66.7%. With the misalignment-rubbing coupling fault, the amplitude of fundamental frequency reduces by 7.4%, the amplitude of 2× fundamental frequency drops by 51.5%, and the amplitude of 3× fundamental frequency drops by 16.8%. Overall, the feasibility of the optimization method of the variable-structured SFD operational parameters for the faulted rotor system is verified. These parametric analyses are very helpful in the development of a high-speed rotor system and provide a theoretical reference for the vibration control and optimal design of rotating machinery.

Magnetorheological damper (MRD), a semi-active control device, has the stability of the passive control device and the adaptive ability of the active control device. It is considered to be an ideal replacement for the squeeze film damper (SFD) and has been extensively investigated. However, the effect mechanism of MRD to a rotor system is still unclear, which will influence the structural design and control strategy of MRD. This paper aims to propose a general MRD excitation model for a rotor system and discover the effect mechanism. First, the effects of current and eccentricity on mechanical properties of MRD are studied in detail and approaches suppressing the vibration amplitude of a rotor system are put forward. Then, a general model considering MRD, ball bearing and squirrel cage is proposed. Based on the finite element method, the dynamic equations of a rotor-bearing-squirrel cage system with MRD and mass imbalance are presented. Finally, the influences of MRD on the dynamic characteristics of the rotor system are investigated, and the effect mechanism is discovered. In addition, the nonlinearity which is not desirable as it causes fluctuating stresses in the main components of the rotor system and eventually leads to their failure due to fatigue, are observed. The changes of damping and stiffness of MRD can alter the damping performance of MRD and the suitable range of current forms the zone of effective damping, which lays helpful guidance for the design and application of the MRD.

Hetero-nanomaterials constructed by plasmonic metals and functional semiconductors show enormous potential in photocatalytic applications, such as in hydrogen production, CO2 reduction, and treatment of pollutants. Their photocatalytic performances can be better regulated through adjusting structure, composition, and components’ arrangement. Therefore, the reasonable design and synthesis of metal/semiconductor hetero-nanostructures is of vital significance. In this mini-review, we laconically summarize the recent progress in efficiently establishing metal/semiconductor nanomaterials for improved photocatalysis. The defined photocatalysts mainly include traditional binary hybrids, ternary multi-metals/semiconductor, and metal/multi-semiconductors heterojunctions. The underlying physical mechanism for the enhanced photocatalysis of the established photocatalysts is highlighted. In the end, a brief summary and possible future perspectives for further development in this field are demonstrated.

Alternative strategies beyond current chemotherapy and radiation therapy regimens are needed in the treatment of advanced stage and recurrent endometrial cancers. There is considerable promise for biologic agents targeting the extracellular signal-regulated kinase (ERK) pathway for treatment of these cancers. Many downstream substrates of the ERK signaling pathway, such as glycogen synthase kinase 3β (GSK3β), and their roles in endometrial carcinogenesis have not yet been investigated. In this study, we tested the importance of GSK3β inhibition in endometrial cancer cell lines and in vivo models. Inhibition of GSK3β by either lithium chloride (LiCl) or specific GSK3β inhibitor VIII showed cytostatic and cytotoxic effects on multiple endometrial cancer cell lines, with little effect on the immortalized normal endometrial cell line. Flow cytometry and immunofluorescence revealed a G2/M cell cycle arrest in both type I (AN3CA, KLE, and RL952) and type II (ARK1) endometrial cancer cell lines. In addition, LiCl pre-treatment sensitized AN3CA cells to the chemotherapy agent paclitaxel. Administration of LiCl to AN3CA tumor-bearing mice resulted in partial or complete regression of some tumors. Thus, GSK3β activity is associated with endometrial cancer tumorigenesis and its pharmacologic inhibition reduces cell proliferation and tumor growth.

The lubrication performance of journal bearings with different sorts of uniformly distributed micro-spherical textures are studied in this paper. Geometries and dynamic models of journal bearings with pure concave/convex textures are developed. The validity of the proposed models is verified against the oil film pressure distribution from the literature. The effects of geometry parameters (the texture depth and the area density) on the load capacity and the friction coefficient of the bearing are analyzed and discussed. Results indicate that: the bearing load capacity is reduced by the concave spherical texture, but enhanced by the convex texture; both the concave and convex textures have a very slight influence on the friction coefficient. Aiming to further improve the bearing lubrication performance, a novel concave-convex composite texture is proposed and modelled. Results show that the composite texture can significantly improve both the load capacity and the friction coefficient, because the concave spherical segments among the convex ones protect the oil film from rupture near the main load region. The oil film region is expanded by the composite texture as well.