Search

Paramagnetic microspheres can be used in planar array fluorescence immunoassays for single or multiplex screening of food contaminants. However, no confirmation of the molecular identity is obtained. Coated blade spray (CBS) is a direct ionization mass spectrometry (MS) technique, and when combined with triple quadrupole MS/MS, it allows for rapid confirmation of food contaminants. The lack of chromatography in CBS, though, compromises the specificity of the measurement for unequivocal identification of contaminants, based on the European Union (EU) regulation. Therefore, a rapid and easy-to-use immuno-magnetic blade spray (iMBS) method was developed in which immuno-enriched paramagnetic microspheres replace the coating of CBS. The iMBS-MS/MS method was fully optimized, validated in-house following the EU 2021/808 regulation, and benchmarked against a commercial lateral flow immunoassay (LFIA) for on-site screening of DA. The applicability of iMBS-MS/MS was further demonstrated by analyzing incurred mussel samples. The combination of immunorecognition and MS/MS detection in iMBS-MS/MS enhances the measurement's selectivity, which is demonstrated by the rapid differentiation between the marine toxin domoic acid (DA) and its structural analog kainic acid (KA), which cannot be achieved with the LFIA alone. Interestingly, this first-ever reported iMBS-MS/MS method is generic and can be adapted to include any other immuno-captured food contaminant, provided that monoclonal antibodies are available, thus offering a complementary confirmatory analysis approach to multiplex immunoassay screening methods. Moreover, thanks to its speed of analysis, iMBS-MS/MS can bridge the logistics gap between future large-scale on-site testings using LFIAs and classical time-consuming confirmatory MS analysis performed in official control laboratories.

On-site testing in food analysis using mass spectrometry (MS) requires miniaturization of vacuum systems, mass analyzers, sample cleanup, and ionization sources. In this study, a simple coated blade spray (CBS) ion source was developed that enables high voltage generation on the blade by ubiquitous certified (micro-)USB On-The-Go devices like smartphones, tablets, and power banks. CBS is capable of performing both analyte enrichment by solid-phase microextraction (SPME) material coated on the metal substrate and direct-spray ionization. The USB-CBS device was used on two different MS systems, a transportable single-quadrupole and a benchtop triple-quadrupole tandem MS. Various characteristics of the USB-CBS device, including high voltage generation and angular positioning, were studied. The potential of the newly developed device for food safety applications is demonstrated by banned and regulated veterinary drugs such as β-agonists and sulfonamide antibiotics, covering a wide range of molecular weights and polarities. The results highlight the potential of the developed, simplified, inexpensive (less than 10 USD), and universal vendor-independent USB-powered CBS ion source coupled with MS(/MS) systems for semiquantitative applications, in laboratories, and in future on-site food quality and safety testing. Apart from that, most likely on-site environmental, biomedical, and forensic testing will also benefit from this USB-CBS instrumental development that is compatible with any atmospheric inlet MS system.

Phycotoxins occur in various marine and freshwater environments, and can accumulate in edible species such as fish, crabs, and shellfish. Human exposure to these toxins can take place, for instance, through consumption of contaminated species or supplements and through the ingestion of contaminated water. Symptoms of phycotoxin intoxication include paralysis, diarrhea, and amnesia. When the cause of an intoxication cannot directly be found, a screening method is required to identify the causative toxin. In this work, such a screening method was developed and validated for marine and freshwater phycotoxins in different matrices: fish, shellfish, water, and food supplements. Two LC methods were developed: one for hydrophilic and one for lipophilic phycotoxins. Sample extracts were measured in full scan mode with an Orbitrap high resolution mass spectrometer. Additionally, a database was created to process the data. The method was successfully validated for most matrices, and in addition, regulated lipophilic phycotoxins, domoic acid, and some paralytic shellfish poisoning toxins could be quantified in shellfish. The method showed limitations for hydrophilic phycotoxins in sea water and for lipophilic phycotoxins in food supplements. The developed method is a screening method; in order to confirm suspected compounds, comparison with a standard or an additional analysis such as NMR is required.

In recent years, conjugated mycotoxins have gained increasing interest in food safety, as their hydrolysis in human and animal intestines leads to an increase in toxicity. For the production of zearalenone (ZEN) glycosides reference standards, we applied Cunninghamellaelegans and Cunninghamella echinulata fungal strains. A sulphate-depleted medium was designed for the preferred production of ZEN glycosides. Both Cunninghamella strains were able to produce zearalenone-14-β-D-glucopyranoside (Z14G), zearalenone-16-β-D-glucopyranoside (Z16G) and zearalenone-14-sulphate (Z14S). In a rich medium, Cunninghamellaelegans preferably produced Z14S, while Cunninghamellaechinulata preferably produced Z14G. In the sulphate-depleted medium a dramatic change was observed for Cunninghamellaelegans, showing preferred production of Z14G and Z16G. From 2 mg of ZEN in sulphate-depleted medium, 1.94 mg of Z14G and 0.45 mg of Z16G were produced. Following preparative Liquid Chromatography-Mass Spectrometry (LC-MS) purification, both fractions were submitted to 1H and 13C NMR and High-Resolution Mass Spectrometry (HRMS). These analyses confirmed that the purified fractions were indeed Z14G and Z16G. In conclusion, the presented research shows that a single Cunninghamella strain can be an effective and efficient tool for the controlled biotransformation of ZEN glycosides and other ZEN metabolites. Additionally, the biotransformation method was extended to zearalanone, β-zearalenol and other mycotoxins.

Tetrodotoxin (TTX) is a potent neurotoxin responsible for many food poisoning incidents and some fatalities. Although mainly associated with the consumption of pufferfish, in recent years, TTX has been found in shellfish, particularly in Europe. In this work, a magnetic bead (MB)-based colorimetric immunoassay was applied to the detection of TTX in Pacific oysters (Crassostrea gigas), razor clams (Solen marginatus) and mussels (Mytilus galloprovincialis). Effective LODs (eLODs) for TTX of 1 μg/kg in oysters and razor clams and 3.3 μg/kg in mussels, significantly below the EFSA guidance threshold (44 μg/kg), were obtained. The strategy was applied to the analysis of naturally-contaminated Pacific oysters (Crassostrea gigas) and mussels (Mytilus edulis) from the Netherlands, and TTX was detected in all samples. The approach, which takes less than 1.5 h, proved to be useful as a rapid and simple method to detect TTX, support shellfish safety and protect consumers. info:eu-repo/semantics/acceptedVersion

In oral bioavailability studies, evaluation of the absorption and transport of drugs and food components across the intestinal barrier is crucial. Advances in the field of organ-on-a-chip technology have resulted in a dynamic gut-on-a-chip model that better mimics the in vivo microenvironment of the intestine. Despite a few recent integration attempts, ensuring a biologically relevant microenvironment while coupling with a fully online detection system still represents a major challenge. Herein, we designed an online technique to measure drug permeability and analyse unknown product formation across an intestinal epithelial layer of Caco-2 and HT29-MTX cells cultured on a flow-through Transwell system, while ensuring the quality and relevance of the biological model. Chip-based ultra-performance liquid chromatography quadrupole time-of-flight mass spectrometry (UPLC-QTOF-MS) was coupled to the dynamic Transwell system via a series of switching valves, thus allowing alternating measurements of the apical and basolateral sides of the in vitro model. Two trap columns were integrated for online sample pre-treatment and compatibility enhancement. Temporal analysis of the intestinal permeability was successfully demonstrated using verapamil as a model drug and ergotamine epimers as a model for natural toxins present in foods. Evidence was obtained that our newly developed dynamic system provided reliable results versus classical static in vitro models, and moreover, for the first time, epimer-specific transport is shown for ergotamine. Finally, initial experiments with the drug granisetron suggest that metabolic activity can be studied as well, thus highlighting the versatility of the bio-integrated online analysis system developed. Graphical abstract Electronic supplementary material The online version of this article (10.1007/s00216-019-02336-6) contains supplementary material, which is available to authorized users.

A fast screening approach for simultaneous detection of twelve pesticides and seven mycotoxins in food and feed samples using flow injection (FI) mass spectrometry (MS) was developed and evaluated. Ten selected pesticides represented five pairs of structural isomers to challenge their MS differentiation without chromatographic separation. Samples of cereals/grains and animal feed were prepared using QuEChERS extraction, diluted and fortified with the selected contaminants to yield their representative maximum levels (MLs) or maximum residue levels (MRLs). Sensitivity of the developed approach was assessed for qualitative screening of the selected contaminants using triple quadrupole MS/MS and ion mobility (IM) HR-TOFMS. Despite the high complexity of the selected matrices and the absence of chromatography, limits of detection in fortified extracts were below established regulatory levels for 14 and 15 selected contaminants by FI-MS/MS and FI-IM-TOFMS analysis, respectively, in 36–100% samples. Experiments with ion mobility TOFMS did not result in successful separation of pesticide structural isomers. However, for three out of five pairs of pesticide structural isomers: cyproconazole and uniconazole, methiocarb and ethiofencarb, and vernolate and pebulate, unique fragment ions were found and confirmed with HR-QTOFMS for their MS differentiation. The developed approach is sensitive enough for rapid multi-residue screening of some pesticides and mycotoxins in complex samples of food and feed, providing high speed and throughput, simplicity and effective use of high-end instrumentation.

Lateral flow immunoassays (LFIAs) are widely used for rapid food safety screening analysis. Thanks to simplified protocols and smartphone readouts, LFIAs are expected to be increasingly used on-site, even by non-experts. As a typical follow-up in EU regulatory settings, suspect samples are sent to laboratories for confirmatory analysis by liquid chromatography-tandem mass spectrometry (LC-MS/MS). However, re-analysis by LC-MS/MS is laborious and time-consuming. In this work, an identification LFIA (ID-LFIA) approach followed by quadrupole-orbitrap MS or triple quadrupole MS/MS analysis is presented. As a proof of concept, a dedicated ID-LFIA strip was developed for the mycotoxin deoxynivalenol (DON) following its initial screening by a commercial smartphone LFIA. The ID-LFIA strip can be simply immersed in the same sample extract used for the smartphone LFIA screening, and next, DON is retrieved from the monoclonal antibody with a dissociation solution consisting of methanol/ammonia. The solution thus obtained was analyzed directly in MS in order to rapidly confirm the presence of DON and any cross-reacting species. The protocol developed is capable of coping with severe ion suppression caused by LFIA buffers and nitrocellulose substrate residues. Initial analysis of blank, spiked, and incurred samples showed that the newly developed ID-LFIA-MS method was able to confirm the presence or absence of mycotoxins in the samples previously analyzed by LFIA and also differentiate between DON and DON 3-glucoside yielding the positive screening result. The concept and technique developed are envisaged to complement on-site screening and confirmation of any low molecular weight contaminant in future food control frameworks. Graphical abstract Electronic supplementary material The online version of this article (10.1007/s00216-020-02890-4) contains supplementary material, which is available to authorized users.

Information on the occurrence and endocrine potencies of analogues of bisphenol A (BPA) and diglycidyl ester derivatives (BDGEs) of BPA and BPF is limited. Such information is, however, important as the current debate on BPA and the lowered BPA migration limit in Europe may provide an incentive for application of structural analogues. A new sensitive multi-analyte LC-ESI-MS/MS method was developed to measure 17 bisphenols (BPs) and 6 BDGEs in food, beverages and drinkware. Yeast based bioassays were used to determine the in vitro (anti)estrogenic and (anti)androgenic properties of these and 7 additional BPs and BDGEs. Drinkware of polycarbonate and other materials were analysed for BPs and BDGEs. Only BPA and BPS and both at trace levels were found in a few containers. A limited number of (canned) foods and beverages were also analysed. BPA was the most frequently detected BP (ranged from 0.03 ng mL−1 in a beverage sample to 68 ng g−1 in food). Other BPs detected were BPS, 2,2-BPF and 4,4-BPF. In addition BADGE, BADGE.HCl, BADGE.H2O and BADGE.2H2O were detected from 0.08 ng mL−1 in a beverage sample to 3.3 ng g−1 in food. In vitro testing showed that most BPs exhibited an equal or higher estrogenic potency than BPA and most of them also showed a higher anti-androgenic potency, i.e. BPB, BPCl, BPC, BPE, 4,4-BPF, BPP, BPAF, and BPTMC. Some BPs and BDGEs were not estrogenic, but showed an anti-estrogenic effect and were anti-androgenic too. BPS was only weakly estrogenic and BADGE.2H2O and BFDGE.2H2O showed no in vitro activity. The present data show that in addition to BPA, other BPs and BDGEs can be present in food and drinks, some displaying in vitro endocrine activities.

The goal of the present study was to obtain an in vivo relevant prioritization method for the endocrine potencies of different polycarbonate monomers, by combining in vitro bioassay data with physiologically based kinetic (PBK) modelling. PBK models were developed for a selection of monomers, including bisphenol A (BPA), two bisphenol F (BPF) isomers and four different bisphenol A diglycidyl ethers (BADGEs), using in vitro input data. With these models, the plasma concentrations of the compounds were simulated, providing means to estimate the dose levels at which the in vitro endocrine effect concentrations are reached. The results revealed that, whereas the in vitro relative potencies of different BADGEs (predominantly anti-androgenic effects) can be up to fourfold higher than BPA, the estimated in vivo potencies based on the oral equivalent doses are one to two orders of magnitude lower than BPA because of fast detoxification of the BADGEs. In contrast, the relative potencies of 2,2-BPF and 4,4-BPF increase when accounting for the in vivo availability. 4,4-BPF is estimated to be fivefold more potent than BPA in humans in vivo in inducing estrogenic effects and both 2,2-BPF and 4,4-BPF are estimated to be, respectively, 7 and 11-fold more potent in inducing anti-androgenic effects. These relative potencies were considered to be first-tier estimates, particularly given that the potential influence of intestinal metabolism on the in vivo availability was not accounted for. Overall, it can be concluded that both 2,2-BPF and 4,4-BPF are priority compounds.

Palytoxin (PlTX) and analogues are produced by certain dinoflagellates, sea anemones, corals and cyanobacteria. PlTX can accumulate in the food chain and when consumed it may cause intoxication with symptoms like myalgia, weakness, fever, nausea, and vomiting. The analysis of PlTXs is challenging, and because of the large molecular structure, it is difficult to develop a sensitive and selective liquid chromatography-mass spectrometry (LC-MS/MS) method. In this work, an LC-MS/MS method was developed to analyse PlTXs with use of lithium iodine and formic acid as additives in the mobile phase. For method development, initially, LC-hrMS was used to accurately determine the elemental composition of the precursor and product ions. The main adduct formed was [M + H + 2Li]3+. Fragments were identified with LC-hrMS and these were incorporated in the LC-MS/MS method. A method of 10 min was developed and a solid phase extraction clean-up procedure was optimised for shellfish matrix. The determined limits of detection were respectively 8 and 22 &micro, g PlTX kg&minus, 1 for mussel and oyster matrix. Oysters gave a low recovery of approximately 50% for PlTX during extraction. The method was successfully in-house validated, repeatability had a relative standard deviation less than 20% (n = 5) at 30 &micro, 1 in mussel, cockle, and ensis, and at 60 &micro, 1 in oyster.

Paralytic shellfish toxins (PSTs) in bivalve molluscs represent a public health risk and are controlled via compliance with a regulatory limit of 0.8 mg saxitoxin (STX)⋅2HCl equivalents per kilogram of shellfish meat (eq/kg). Shellfish industries would benefit from the use of rapid immunological screening tests for PSTs to be used for regulation, but to date none have been fully validated. An interlaboratory study involving 16 laboratories was performed to determine the suitability of the Neogen test to detect PSTs in mussels and oysters. Participants performed the standard protocol recommended by the manufacturer and a modified protocol with a conversion step to improve detection of gonyautoxin 1&4. The statistical analysis showed that the protocols had good homogeneity across all laboratories, with satisfactory repeatability, laboratory, and reproducibility variation near the regulatory level. The mean probability of detection (POD) at 0.8 mg STX⋅2HCl eq/kg using the standard protocol in mussels and oysters was 0.966 and 0.997, respectively, and 0.968 and 0.966 using the modified protocol. The estimated LOD in mussels was 0.316 mg STX⋅2HCl eq/kg with the standard and 0.682 mg STX⋅2HCl eq/kg with the modified protocol, and 0.710 and 0.734 mg STX⋅2HCl eq/kg for oysters, respectively. The Neogen test may be acceptable for regulatory purposes for oysters in accordance with European Commission directives in which the standard protocol provides, at the regulatory level, a probability of a negative response of 0.033 on 95% of occasions. Its use for mussels is less consistent at the regulatory level due to the wide prediction interval around the POD.

The recent detection of tetrodotoxins (TTXs) in puffer fish and shellfish in Europe highlights the necessity to monitor the levels of TTXs in seafood by rapid, specific, sensitive and reliable methods in order to protect human consumers. A previous immunoassay for TTX detection in puffer fish, based on the use of self-assembled monolayers (SAMs) for the immobilization of TTX on maleimide plates (mELISA), has been modified and adapted to the analysis of oyster and mussel samples. Changing dithiol for cysteamine-based SAMs enabled reductions in the assay time and cost, while maintaining the sensitivity of the assay. The mELISA showed high selectivity for TTX since the antibody did not cross-react with co-occurring paralytic shellfish poisoning (PSP) toxins and no interferences were observed from arginine (Arg). Moreover, TTX-coated maleimide plates stored for 3 months at −20 °C and 4 °C were stable, thus when pre-prepared, the time to perform the assay is reduced. When analyzing shellfish samples, matrix effects and toxin recovery values strongly depended on the shellfish type and the sample treatment. Blank oyster extracts could be directly analyzed without solid-phase extraction (SPE) clean-up, whereas blank mussel extracts showed strong matrix effects and SPE and subsequent solvent evaporation were required for removal. However, the SPE clean-up and evaporation resulted in toxin loss. Toxin recovery values were taken as correction factors (CFs) and were applied to the quantification of TTX contents in the analysis of naturally-contaminated shellfish samples by mELISA. The lowest effective limits of detection (eLODs) were about 20 and 50 µg/kg for oyster extracts without and with SPE clean-up, respectively, and about 30 µg/kg for mussel extracts with both protocols, all of them substantially below the eLOD attained in the previous mELISA for puffer fish (230 µg/kg). Analysis of naturally-contaminated samples by mELISA and comparison with LC-MS/MS quantifications demonstrated the viability of the approach. This mELISA is a selective and sensitive tool for the rapid detection of TTX in oyster and mussel samples showing promise to be implemented in routine monitoring programs to protect human health. info:eu-repo/semantics/acceptedVersion

The dinoflagellate Alexandrium ostenfeldii is a well-known harmful algal species that can potentially cause paralytic shellfish poisoning (PSP). Usually A. ostenfeldii occurs in low background concentrations only, but in August of 2012 an exceptionally dense bloom of more than 1 million cells L-1 occurred in the brackish Ouwerkerkse Kreek in The Netherlands. The A. ostenfeldii bloom produced both saxitoxins and spirolides, and is held responsible for the death of a dog with a high saxitoxin stomach content. The Ouwerkerkse Kreek routinely discharges its water into the adjacent Oosterschelde estuary, and an immediate reduction of the bloom was required to avoid contamination of extensive shellfish grounds. Previously, treatment of infected waters with hydrogen peroxide (H2O2) successfully suppressed cyanobacterial blooms in lakes. Therefore, we adapted this treatment to eradicate the Alexandrium bloom using a three-step approach. First, we investigated the required H2O2 dosage in laboratory experiments with A. ostenfeldii. Second, we tested the method in a small, isolated canal adjacent to the Ouwerkerkse Kreek. Finally, we brought 50 mg L-1 of H2O2 into the entire creek system with a special device, called a water harrow, for optimal dispersal of the added H2O2. Concentrations of both vegetative cells and pellicle cysts declined by 99.8% within 48 h, and PSP toxin concentrations in the water were reduced below local regulatory levels of 15 µg L-1. Zooplankton were strongly affected by the H2O2 treatment, but impacts on macroinvertebrates and fish were minimal. A key advantage of this method is that the added H2O2 decays to water and oxygen within a few days, which enables rapid recovery of the system after the treatment. This is the first successful field application of H2O2 to suppress a marine harmful algal bloom, although Alexandrium spp. reoccurred at lower concentrations in the following year. The results show that H2O2 treatment provides an effective emergency management option to mitigate toxic Alexandrium blooms, especially when immediate action is required.

A generic high-throughput bioaffinity liquid chromatography-mass spectrometry (BioMS) approach was developed and applied for the screening and identification of known and unknown recombinant human sex hormone-binding globulin (rhSHBG)-binding designer steroids in dietary supplements. For screening, a semi-automated competitive inhibition binding assay was combined with fast ultrahigh-performance-LC-electrospray ionization-triple-quadrupole-MS (UPLC-QqQ-MS). 17β-Testosterone-D3 was used as the stable isotope label of which the binding to rhSHBG-coated paramagnetic microbeads was inhibited by any other binding (designer) steroid. The assay was performed in a 96-well plate and combined with the fast LC-MS, 96 measurements could be performed within 4 h. The concentration-dependent inhibition of the label by steroids in buffer and dietary supplements was demonstrated. Following an adjusted bioaffinity isolation procedure, suspect extracts were injected into a chip-UPLC(NanoTile)-Q-time-of-flight-MS system for full-scan accurate mass identification. Next to known steroids, 1-testosterone was identified in three of the supplements studied and the designer steroid tetrahydrogestrinone was identified in a spiked supplement. The generic steroid-binding assay can be used for high-throughput screening of androgens, estrogens, and gestagens in dietary supplements to fight doping. When combined with chip-UPLC-MS, it is a powerful tool for early warning of unknown emerging rhSHBG bioactive designer steroids in dietary supplements.

A new LC-MS/MS method for the separation and detection of the most prominent marine lipophilic toxin groups comprising okadaic acid, dinophysistoxins, yessotoxins, azaspiracids, pectenotoxins, spirolides and some okadaic acid fatty acid esters has been developed. With this method 28 different marine lipophilic biotoxins can be analysed in a single run. Separation was achieved with an acetonitrile/water gradient containing ammonium hydroxide (pH 11). All toxins were stable under these basic conditions. Compared to chromatography using an acidic gradient, the limit of detection (LODs) for okadaic acid, yessotoxin, gymnodimine and 13-desmethyl spirolide C were improved two- to three-fold, mainly due to better peak shapes. The azaspiracids and pectenotoxins-2 showed comparable LODs under acidic and basic conditions. A major advantage of the developed method is that toxins can be clustered in retention time windows separated for positively and negatively ionized molecular ions. Therefore, there is no need for rapid polarity switching or two separate runs for one sample. The new method showed good repeatability and reproducibility and is an important step in the development of alternatives to the animal tests currently in use for shellfish toxin analysis. © 2009 Elsevier B.V. All rights reserved.

The performances of four different mass spectrometers [triple-quadrupole (TQ), time-of-flight (ToF), quadrupole ToF (Q-ToF) and ion trap (IT)] for the detection of the marine lipophilic toxins pectenotoxin-2 (PTX2) and okadaic acid (OA) were investigated. The spectral data obtained with the different mass spectrometric analyzers were used to propose fragmentation schemes for PTX2 in the positive electrospray mode and for OA in the negative electrospray mode. TQ data were used to obtain product ions, while ToF and Q-ToF-MS produced accurate mass data of the precursor ion and product ions, respectively. IT data provided a better understanding of the fragmentation pathways using MS(n) experiments. With respect to analytical performance, all four mass analyzers showed a good linearity (R(2)0.97) and repeatability (CV20%). Detection limits (LoDs) (S/N = 3) were the lowest on triple-quad MS: 12.2 and 2.9 pg on-column for PTX2 and OA, respectively.

Excited-state intramolecular proton transfer (ESIPT) occurring in the salicylic acid (SA) derivative 5-methoxysalicylic acid (5-MeOSA) in an apolar solvent (cyclohexane) and in the presence of the hydrogen bond accepting agent diethyl ether (DEE) is investigated. Analysis of the directly measured subnanosecond time-resolved emission spectra (TRES) together with conventional steady-state fluorescence and time-correlated single-photon-counting (TCSPC) decays indicates that ESIPT in this system occurs much faster than fluorescence, and that the equilibrium between normal and tautomeric excited states is established before the emission from both states takes place. However, changes in time- and frequency-resolved fluorescence of the 5-MeOSA/DEE complex are observed due to structural relaxation within the complex, which is reflected in the dynamic Stokes shift of the tautomeric fluorescence band. The normal fluorescence band of 5-MeOSA/ DEE does not exhibit marked changes within the investigated time range. A single-exponential relaxation time of 460 ps was determined for the dynamic Stokes shift of the tautomeric band, and it is attributed to a geometric change within the 5-MeOSA/DEE complex upon excitation. Since both tautomeric and normal emission bands are well resolved and exhibit different time-dependent behaviors, a double-well potential appears to be adequate to describe the excited state of the system studied.

In this preliminary study, we evaluated four different types of substrate for the at-line coupling of capillary electrophoresis and surface-enhanced (resonance) Raman spectroscopy, CE-SER(R)S, with emphasis on spectral repeatability. We tested Sub1: etched silver foil, Sub2: a vapour-deposited silver film, Sub3: a silver oxalate-precoated silica TLC plate and Sub4: a silica TLC plate on which colloid and poly(L-lysine) were manually added to the analyte spots, used earlier in at-line CE-SE(R)RS. All substrates were first tested by manual spotting using trans-1,2-bis(4-pyridyl)ethylene (BPE) as a model compound for SERS and crystal violet (CV) as a model compound for SE(R)RS. The spectral features of the SE(R)RS spectra of BPE and CV showed a most satisfactory repeatability on all substrates. As expected, the signal intensities varied considerably between runs; this implies that quantification in at-line CE-SE(R)RS should rather be done by means of an on-line absorbance detector. In addition, the suitability of Sub1, Sub2 and Sub4 as deposition substrates after CE was explored using two cationic dyes: CV and basic fuchsin (BF). Good-quality SERRS spectra could be recorded on all three substrates. Although Sub1 and Sub2 have a poor water-sorptivity, they were found to be good substrates for at-line CE-SERRS. They do not require any post-deposition addition of silver colloid and could therefore become attractive alternatives for Sub4. © 2003 Elsevier B.V. All rights reserved.

Most liquid chromatography (LC) mass spectrometric (MS) methods used for routine monitoring of lipophilic marine toxins focus on the analysis of the 13 toxins that are stated in European Union legislation. However, to date over 200 lipophilic marine toxins have been described in the literature. To fill this gap, a screening method using LC coupled to high resolution (HR) orbitrap MS (resolution 100. 000) for marine lipophilic toxins has been developed. The method can detect a wide variety of okadaic acid (OA), yessotoxin (YTX), azaspiracid (AZA) and pectenotoxin (PTX) group toxins. To build a library of toxins, shellfish and algae samples with various toxin profiles were obtained from Norway, Ireland, United Kingdom, Portugal and Italy. Each sample extract was analyzed with and without collision induced dissociation fragmentation. Based on their mass and specific fragmentation pattern, 85 different toxins were identified comprising 33 OA, 26 YTX, 18 AZA and 8 PTX group toxins. A major complication of full scan HRMS is the huge amount of data generated (file size), which restricts the possibility of a fast search. A software program called metAlign was used to reduce the orbitrap MS data files. The 200-fold reduced data files were screened using an additional software tool for metAlign: 'Search_LCMS'. A search library was constructed for the 85 identified toxins. The library contains information about compound name, accurate mass, mass deviation (

A liquid chromatography tandem mass spectrometry (LC-MS/MS) method for the quantitative analysis of lipophilic marine toxins in shellfish extracts (mussel, oyster, cockle and clam) was validated in-house using European Union (EU) Commission Decision 2002/657/EC as a guideline. The validation included the toxins okadaic acid (OA), yessotoxin (YTX), azaspiracid-1 (AZA1), pectenotoxin-2 (PTX2) and 13-desmethyl spirolide-C (SPX1). Validation was performed at 0.5, 1 and 1.5 times the current EU permitted levels, which are 160 µg kg-1 for OA, AZA1 and PTX2 and 1,000 µg kg-1 for YTX. For SPX1, 400 µg kg-1 was chosen as the target level as no legislation has been established yet for this compound. The method was validated for determination in crude methanolic shellfish extracts and for extracts purified by solid-phase extraction (SPE). Extracts were also subjected to hydrolysis conditions to determine the performance of the method for OA and dinophysistoxin esters. The toxins were quantified against a set of matrix-matched standards instead of standard solutions in methanol. To save valuable standard, methanolic extract instead of the homogenate was spiked with the toxin standard. This was justified by the fact that the extraction efficiency is high for all relevant toxins (above 90%). The method performed very well with respect to accuracy, intraday precision (repeatability), interday precision (within-laboratory reproducibility), linearity, decision limit, specificity and ruggedness. At the permitted level the accuracy ranged from 102 to 111%, the repeatability from 2.6 to 6.7% and the reproducibility from 4.7 to 14.2% in crude methanolic extracts. The crude extracts performed less satisfactorily with respect to the linearity (less than 0.990) and the change in LC-MS/MS sensitivity during the series (more than 25%). SPE purification resulted in greatly improved linearity and signal stability during the series. Recently the European Food Safety Authority (EFSA) has suggested that to not exceed the acute reference dose the levels should be below 45 µg kg-1 OA equivalents and 30 µg kg-1 AZA1 equivalents. A single-day validation was successfully conducted at these levels. If the regulatory levels are lowered towards the EFSA suggested values, the official methods prescribed in legislation (mouse and rat bioassay) will no longer be sensitive enough. The validated LC-MS/MS method presented has the potential to replace these animal tests. Electronic supplementary material The online version of this article (doi:10.1007/s00216-010-3886-2) contains supplementary material, which is available to authorized users.

The potential of solid phase extraction (SPE) clean-up has been assessed to reduce matrix effects (signal suppression or enhancement) in the liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis of lipophilic marine toxins. A large array of ion-exchange, silica-based, and mixed-function SPE sorbents was tested. Polymeric sorbents were found to retain most of the toxins. Optimization experiments were carried out to maximize recoveries and the effectiveness of the clean-up. In LC-MS/MS analysis, the observed matrix effects can depend on the chromatographic conditions used, therefore, two different HPLC methods were tested, using either an acidic or an alkaline mobile phase. The recovery of the optimized SPE protocol was around 90% for all toxins studied and no break-through was observed. The matrix effects were determined by comparing signal response from toxins spiked in crude and SPE-cleaned extracts with those derived from toxins prepared in methanol. In crude extracts, all toxins suffered from matrix effects, although in varying amounts. The most serious effects were observed for okadaic acid (OA) and pectenotoxin-2 (PTX2) in the positive electrospray ionization mode (ESI(+)). SPE clean-up on polymeric sorbents in combination with the alkaline LC method resulted in a substantial reduction of matrix effects to less than 15% (apparent recovery between 85 and 115%) for OA, yessotoxin (YTX) in ESI(-) and azaspiracid-1 (AZA1), PTX2, 13-desmethyl spirolides C (SPX1), and gymnodimine (GYM) in ESI(+). In combination with the acidic LC method, the matrix effects after SPE were also reduced but nevertheless approximately 30% of the matrix effects remained for PTX2, SPX1, and GYM in ESI(+). It was concluded that SPE of methanolic shellfish extracts can be very useful for reduction of matrix effects. However, the type of LC and MS methods used is also of great importance. SPE on polymeric sorbents in combination with LC under alkaline conditions was found the most effective method.

The practicability of an at-line capillary electrophoresis–surface-enhanced resonance Raman spectroscopy configuration was explored. To achieve electrical contact, a metallized outlet capillary was used. The CE effluent was deposited on a moving thin layer chromatography plate. Next, the deposited analytes – three acidic dyes (Food Yellow 3, Acid Orange 7 and Food Red 1) – were treated with silver sol and poly(L-lysine) or nitric acid, followed by irradiation with 514.5 nm light from an argon ion laser to record the SERRS signal. Analyte confirmation could be achieved down to a few pmoles deposited on the TLC plate.

Multi-analyte binding assays for rapid screening of food contaminants require mass spectrometric identification of compound(s) in suspect samples. An optimal combination is obtained when the same bioreagents are used in both methods; moreover, miniaturisation is important because of the high costs of bioreagents. A concept is demonstrated using superparamagnetic microbeads coated with monoclonal antibodies (Mabs) in a novel direct inhibition flow cytometric immunoassay (FCIA) plus immunoaffinity isolation prior to identification by nano-liquid chromatography–quadrupole time-of-flight-mass spectrometry (nano-LC-Q-ToF-MS). As a model system, the mycotoxin ochratoxin A (OTA) and cross-reacting mycotoxin analogues were analysed in wheat and cereal samples, after a simple extraction, using the FCIA with anti-OTA Mabs. The limit of detection for OTA was 0.15 ng/g, which is far below the lowest maximum level of 3 ng/g established by the European Union. In the immunomagnetic isolation method, a 350-times-higher amount of beads was used to trap ochratoxins from sample extracts. Following a wash step, bound ochratoxins were dissociated from the Mabs using a small volume of acidified acetonitrile/water (2/8 v/v) prior to separation plus identification with nano-LC-Q-ToF-MS. In screened suspect naturally contaminated samples, OTA and its non-chlorinated analogue ochratoxin B were successfully identified by full scan accurate mass spectrometry as a proof of concept for identification of unknown but cross-reacting emerging mycotoxins. Due to the miniaturisation and bioaffinity isolation, this concept might be applicable for the use of other and more expensive bioreagents such as transport proteins and receptors for screening and identification of known and unknown (or masked) emerging food contaminants. Figure Microbead coated with antibody