Search

The use of microalgae and bacteria as a strategy for the startup of bioreactors for the treatment of industrial wastewater can be a sustainable and economically viable alternative. This technology model provides satisfactory results in the nitrification and denitrification process for nitrogen removal, organic matter removal, biomass growth, sedimentation, and byproducts recovery for added-value product production. The objective of this work was to evaluate the performance of microalgae and bacteria in their symbiotic process when used in the treatment of paper pulp industry wastewater. The experiment, lasting fourteen days, utilized four bioreactors with varying concentrations in mgVSS/L of microalgae to bacteria ratio (R1-100:100, R2-100:300, R3-100:500, R4-300:100) in the startup process. Regarding the sludge volumetric index (SVI), the results show that the R1 and R2 reactors developed SVI30/SVI10 biomass in the range of 85.57 ± 7.33% and 84.72 ± 8.19%, respectively. The lipid content in the biomass of reactors R1, R2, R3 e R4 was 13%, 7%, 19%, and 22%, respectively. This high oil content at the end of the batch, may be related to the nutritional stress that the species underwent during this feeding regime. In terms of chlorophyll, the bioreactor with an initial inoculation of 100:100 showed better symbiotic growth of microalgae and bacteria, allowing exponential growth of microalgae. The total chlorophyll value for this bioreactor was 801.46 ± 196.96 μg/L. Biological removal of nitrogen from wastewater from the paper pulp industry is a challenge due to the characteristics of the effluent, but the four reactors operated in a single batch obtained good nitrogen removal. Ammonia nitrogen removal performances were 91.55 ± 9.99%, 72.13 ± 19.18%, 64.04 ± 21.34%, and 86.15 ± 30.10% in R1, R2, R3, and R4, respectively., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The production processes of the pulp and paper industry often run in campaigns, leading to large variations in the composition of wastewaters and waste sludges. During anaerobic digestion (AD) of these wastes, the viscosity or the production of extracellular polymeric substances (EPS) and soluble microbial products (SMP) may be affected, with the risk of foam formation, inefficient digester mixing or poor sludge dewaterability. The aim of this study was to investigate how viscosity and production of EPS and SMP during long-term AD of pulp and paper mill sludge is affected by changes in organic loading rate (OLR) and hydraulic retention time (HRT). Two mesophilic lab-scale continuous stirred tank reactors (CSTRs) were operated for 800 days (R1 and R2), initially digesting only fibre sludge, then co-digesting fibre sludge and activated sludge. The HRT was lowered, followed by an increase in the OLR. Reactor fluids were sampled once a month for rheological characterization and analysis of EPS and SMP. The production of the protein fraction of SMP was positively correlated to the OLR, implicating reduced effluent qualities at high OLR. EPS formation correlated with the magnesium content, and during sulphate deficiency, the production of EPS and SMP increased. At high levels of EPS and SMP, there was an increase in viscosity of the anaerobic sludges, and dewatering efficiency was reduced. In addition, increased viscosity and/or the production of EPS and SMP were important factors in sludge bulking and foam formation in the CSTRs. Sludge bulking was avoided by more frequent stirring.

Objective: The main objective of this study is the evaluation of RPPW anaerobic digestion feasibility at laboratory scale under Mesophilic condition. The experiment is conducted using a two-stage biofilm digester of 5 L capacity with mobile support material., Results: Anaerobic treatment of wastewater from recycled pulp and paper industry in Morocco was tested using a laboratory-scale anaerobic biofilm digester that operated under mesophilic conditions over a 70-day. Chemical oxygen demand (COD) efficiency, volatile and total solid (VS, TS) elimination of the substrate during the process were: 78%, 52% and 48% respectively. The system was stable throughout its operating cycle with an optimum pH (7.24), alkalinity (1750 mg CaCO 3 /L) and a volatile fatty acid value (760 mg/L). The experimental daily biogas production measured reaches a value of 5 L/day with a composition of 71% methane, 27.6% carbon dioxide, 0.2 oxygen and 7713 ppm of the H 2 S. The study results show that the anaerobic biofilm reactor is a suitable technique for recycled pulp and paper wastewater (RPPW) treatment. The reactor shows high performances in terms of process stability, removal efficiency (> 70%) and biogas production., Conclusion: Anaerobic digestion is an efficient waste treatment technology that uses natural anaerobic decomposition to reduce the volume of waste while producing biogas. However, research is needed to strengthen microbial metabolism, biochemistry and the functioning of the rector to improve biogas production. The RPPW AD experiment with biofilm digester technology was stable throughout the operation period. The digester knows an overloaded in the last phase of the experiment which leads to an inhibition of biogas production.

Secondary effluent from paper mill was characterized by poor biodegradability and containing recalcitrant compounds. In this study, four bioreactors, including a sequencing batch biofilm reactor (SBBR), a stirred-tank reactor (STR) and two submerged aeration reactors (SAR) were used to treat secondary effluent from a recycled paper mill respectively. The results indicated that chemical oxygen demand (COD) was increased by SAR2 treatment and COD removal efficiency for SBBR, SAR1 and STR was 39.7%, 15.7% and 30.9% respectively. It is suggested that recalcitrant compounds were removed by SBBR, SAR1 and STR respectively. Total nitrogen (TN) and total phosphorus (TP) of wastewater were increased by treatments of each bioreactor, which suggested that endogenous respiration of biomass occurred during the treatment. Microbial analysis of sludge from different bioreactors suggested that the removal of recalcitrant compounds in SBBR and STR might be related to the presence of unique microorganisms in each reactor., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Microbial content formed in bioreactors plays a significant role in the anaerobic process. Therefore, the physicochemical characteristics of microbial content in a modified anaerobic inclining-baffled reactor (MAI-BR) treating recycled paper mill effluent (RPME) were investigated using Fourier transform infrared (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermogravimetric (TG), and derivative thermogravimetric (DTG) analyses, scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS), Brunauer-Emmett-Teller (BET), and surface area analyzer. FTIR spectra revealed that the microbial content had stronger characteristic peaks corresponding to alcohols, water, lipids carbohydrates, proteins, and mineral compounds. Calcite, muscovite, and lepidolite were the prevalent mineral phases found by XRD analysis. The elemental of these minerals like C, Ca, N, O, and Si was confirmed by XPS results. The microbial content samples from each compartment showed similar thermal behavior. SEM images showed that straight rod-shaped and Methanosaeta-like microorganisms were predominant, whereas C, O, and Ca were noticed by EDS on the surface of granules. The BET surface areas and pores of granules are found to decline throughout the reactor's compartment, where Compartment 1 had the largest values. Thus, the findings of this study establish further understanding of the physicochemical properties of microbial content formed in MAI-BR during the RPME treatment.

The performance of modified anaerobic inclining-baffled reactor (MAI-BR) treating recycled paper mill effluent (RPME) was investigated by varying the influent chemical oxygen demand (COD in ) concentration from 1000 to 4000 mg/L, and the hydraulic retention time (HRT) from 3 to 1 day, corresponding to an organic loading rate increase from 0.33 to 4 g COD/L day. Throughout 126 days of operation, a maximum removal efficiency of up to 96% of chemical oxygen demand (COD) and 99% of biological oxygen demand, methane (CH 4 ) yield of 0.259 L CH 4 /g COD, and a stable effluent pH of 6.5 were achieved. Furthermore, the compartmental performance showed that most of the organic substrates were removed in the initial two compartments, resulting in low pH and alkalinity levels and a high concentration of volatile fatty acids. Overall, the results showed that the MAI-BR successfully treated RPME, and the performance was affected by the variation of HRT more than the COD in .

The paper mill industry produces high amounts of wastewater and, for this reason, stringent discharge limits are applied for sustainable reclamation and reuse of paper mill industry wastewater in many countries. Submerged membrane bioreactor (sMBR) systems can create new opportunities to eliminate dissolved substances present in paper mill wastewater including. In this study, a sMBR was operated for the treatment of paper mill industry wastewater at 35 h of hydraulic retention time (HRT) and 40 d of sludge retention time (SRT). The chemical oxygen demand (COD), NH 3 -N and total phosphorus (TP) removal efficiencies were found to be 98%, 92.99% and 96.36%. The results demonstrated that sMBR was a suitable treatment for the removal of organic matter and nutrients for treating paper mill wastewater except for the problem of calcium accumulation. During the experimental studies, it was noted that the inorganic fraction of the sludge increased as a result of calcium accumulation in the reactor and increased membrane fouling was observed on the membrane surface due to the calcification problem encountered. The properties of the sludge, such as extracellular polymeric substances (EPS) and soluble microbial products (SMP), relative hydrophobicity, zeta potential and floc size distribution were also monitored. According to the obtained results, the total EPS was found to be 43.93 mg/gMLSS and the average total SMP rejection by the membrane was determined as 66.2%.

Anaerobic digestion (AD) of lignocellulosic materials is commonly limited by the hydrolysis step. Unlike unprocessed lignocellulosic materials, paper and paper board (PPB) are processed for their fabrication. Such modifications may affect their methane yields and methane production rates. Previous studies have investigated the correlation between lignin and biomethane yields of unprocessed lignocellulosic materials; nevertheless, there is limited knowledge regarding the relationship between the AD kinetic parameters and composition of PPB. This study evaluated correlations of methane yields and Monod and Gompertz kinetic parameters with structural carbohydrates, lignin, and ash concentration of five types of PPBs. All components were used as single and combined independent variables in linear regressions to predict methane yield, maximum specific methanogenic activity (SMA max ), saturation constant (K s ), and lag phase (λ). Additionally, microbial community profiles were obtained for each PPB assay. Results showed methane yields ranging from 69.2 ± 8.61 to 97.2 ± 2.29% of PPB substrates provided. The highest correlation coefficients were obtained for SMA max as function of hemicellulose/(lignin + ash) (R 2  = 0.86) and for λ as a function of lignin + cellulose (R 2  = 0.85). All other parameters exhibited weaker correlations (R 2  ≤ 0.77). Relative abundance analyses revealed no major changes in the community profile for each of the substrates evaluated. The overall findings of this study are: (i) combinations of structural carbohydrates, lignin, and ash used as ratios of degradable to either non-degradable or slowly degradable fractions predict AD kinetic parameters of PPB materials better than single independent variables; and (ii) other components added during their fabrication may also influence both methane yield and kinetic parameters. Biotechnol. Bioeng. 2017;114: 951-960. © 2016 Wiley Periodicals, Inc., (© 2016 Wiley Periodicals, Inc.)

Recycled paper mill effluent (RPME) contains high levels of organic and solid compounds, causing operational problems for anaerobic biological treatment. In this study, a unique modified anaerobic inclining-baffled reactor (MAI-BR) has been developed to treat RPME at various initial chemical oxygen demand (COD) concentrations (1000-4000 mg/L) and hydraulic retention times (HRTs) (3 and 1 day). The COD removal efficiency was decreased from 96 to 83% when the organic loading rate (OLR) was increased from 0.33 to 4 g/L day. Throughout the study, a maximum methane yield of 0.25 L CH 4 /g COD was obtained, while the pH fluctuated in the range of 5.8 to 7.8. The reactor performance was influenced by the development and distribution of the microbial communities. Based on the next-generation sequencing (NGS) analysis, the microbial community represented a variety of bacterial phyla with significant homology to Euryarchaeota (43.06%), Planctomycetes (24.68%), Proteobacteria (21.58%), Acidobacteria (4.12%), Chloroflexi (3.14%), Firmicutes (1.12%), Bacteroidetes (1.02%), and others (1.28%). The NGS analysis showed that the microbial community was dominated by Methanosaeta concilii and Candidatus Kuenenia stuttgartiensis. This can be supported by the presence of filamentous and spherical microbes of different sizes. Additionally, methanogenic and anaerobic ammonium oxidation (ANAMMOX) microorganisms coexisted in all compartments, and these contributed to the overall degradation of substances in the RPME. Graphical abstract ᅟ.

This paper presents the development and evaluation of three fuzzy neural network (FNN) models for a full-scale anaerobic digestion system treating paper-mill wastewater. The aim was the investigation of feasibility of the approach-based control system for the prediction of effluent quality and biogas production from an internal circulation (IC) anaerobic reactor system. To improve FNN performance, fuzzy subtractive clustering was used to identify model's architecture and optimize fuzzy rule, and a total of 5 rules were extracted in the IF-THEN format. Findings of this study clearly indicated that, compared to NN models, FNN models had smaller RMSE and MAPE as well as bigger R for the testing datasets than NN models. The proposed FNN model produced smaller deviations and exhibited a superior predictive performance on forecasting of both effluent quality and biogas (methane) production rates with satisfactory determination coefficients greater than 0.90. From the results, it was concluded that FNN modeling could be applied in IC anaerobic reactor for predicting the biodegradation and biogas production using paper-mill wastewater.

Kraft fibre sludge from the pulp and paper industry constitutes a new, widely available substrate for the biogas production industry, with high methane potential. In this study, anaerobic digestion of kraft fibre sludge was examined by applying continuously stirred tank reactors (CSTR) with sludge recirculation. Two lab-scale reactors (4L) were run for 800days, one on fibre sludge (R1), and the other on fibre sludge and activated sludge (R2). Additions of Mg, K and S stabilized reactor performance. Furthermore, the Ca:Mg ratio was important, and a stable process was achieved at a ratio below 16:1. Foaming was abated by short but frequent mixing. Co-digestion of fibre sludge and activated sludge resulted in more robust conditions, and high-rate operation at stable conditions was achieved at an organic loading rate of 4g volatile solids (VS)L(-1)day(-1), a hydraulic retention time of 4days and a methane production of 230±10NmL per g VS., (Copyright © 2016. Published by Elsevier Ltd.)

We propose a novel approach to continuous bioprocessing of gases. A miniaturized, coated-paper strip, high gas fraction, biocomposite absorber has been developed using slowly shaken horizontal anaerobic tubes. Concentrated Clostridium ljungdahlii OTA1 was used as a model system. These gas absorbers demonstrate elevated CO mass transfer with low power input, reduced liquid requirements, elevated substrate consumption, and increased product secretion compared to shaken suspended cells. Concentrated OTA1 cell paste was coated by extrusion onto chromatography paper. The immobilized system shows high, constant reactivity immediately upon rehydration. Cell adhesion was by adsorption to the cellulose fibers; visualized by SEM. The C. ljungdahlii OTA1 coated paper mounted above the liquid level absorbs CO and H2 from a model syngas secreting acetate with minimal ethanol. At 100 rpm shaking speed (7.7 Wm(-3) ) the optimal cell loading is 6.5 gDCW m(-2) to maintain high CO absorbing reactivity without the cells coming off of the paper into the liquid phase. Reducing the medium volume from 10 mL to 4 mL (15% of tube volume) did not decrease CO reactivity. The reduced liquid volume increased secreted product concentration by 80%. The specific CO consumption by paper biocomposites was higher at all shaking frequencies <100 rpm than suspended cells under identical incubation conditions. At 25 rpm the biocomposite outperforms suspended cells for CO absorption by 2.5-fold, with an estimated power reduction of 97% over the power input at 100 rpm. The estimated minimum kL a for miniaturized biocomposite gas-absorbers is ∼100 h(-1) , 10 to 10(4) less power input than other syngas fermentation systems reported in the literature at similar kL a. Specific consumption rates in a biocomposite were ∼14 mmol gDCW-1 h(-1) . This work intensified CO absorption and reactivity by 14-fold to 94 mmol CO m(-2) h(-1) over previous C. ljungdahlii OTA1 work by our group. Specific acetate production rates were 23 mM h(-1) or 46 mmol m(-2) h(-1) . The specific rates and apparent kL a scaled linearly with biocomposite coating area. Biotechnol. Bioeng. 2016;113: 1913-1923. © 2016 Wiley Periodicals, Inc., (© 2016 Wiley Periodicals, Inc.)

Investigation of cell signaling pathways is important for the study of pathogenesis of cancer. However, the related operations used in these studies are time consuming and labor intensive. Thus, the development of effective therapeutic strategies may be hampered. In this work, gel-free cell culture and subsequent immunoassay has been successfully integrated and conducted in a paper-based microreactor array. Study of the activation level of different kinases of cells stimulated by different conditions, i.e., IL-6 stimulation, starvation, and hypoxia, was demonstrated. Moreover, rapid screening of cell signaling cascades after the stimulations of HGF, doxorubicin, and UVB irradiation was respectively conducted to simultaneously screen 40 kinases and transcription factors. Activation of multi-signaling pathways could be identified and the correlation between signaling pathways was discussed to provide further information to investigate the entire signaling network. The present technique integrates most of the tedious operations using a single paper substrate, reduces sample and reagent consumption, and shortens the time required by the entire process. Therefore, it provides a first-tier rapid screening tool for the study of complicated signaling cascades. It is expected that the technique can be developed for routine protocol in conventional biological research laboratories.

Filter paper strips were enclosed between two poly(methyl methacrylate) plates to fabricate paper-packed channel microchips under pressure in the presence of far infrared irradiation. After the enclosed paper strip was oxidized by periodate, trypsin was covalently immobilized in them to fabricate microfluidic proteolysis bioreactor. The feasibility and performance of the unique bioreactor were demonstrated by digesting BSA and lysozyme. The results were comparable to those of conventional in-solution proteolysis while the digestion time was significantly reduced to ∼18 s. The suitability of the microfluidic paper-based bioreactors to complex proteins was demonstrated by digesting human serum., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

The pulp and paper industry wastewater treatment processes produce large volumes of biosludge. Limited anaerobic degradation of lignocellulose has hindered the utilization of biosludge, but the processing of biosludge using anaerobic digestion has recently regained interest. In this study, biosludge was used as a sole substrate in long-term (400 d) mesophilic laboratory reactor trials. Nine biosludge batches collected evenly over a period of one year from a pulp and paper industry wastewater treatment plant had different solid and nutrient (nitrogen, phosphorus, trace elements) characteristics. Nutrient characteristics may vary by a factor of 2-11, while biomethane potentials (BMPs) ranged from 89 to 102 NL CH4 kg(-1) VS between batches. The BMPs were enhanced by 39-88% with thermal pretreatments at 105-134 °C. Despite varying biosludge properties, stable operation was achieved in reactor trials with a hydraulic retention time (HRT) of 14 d. Hydrolysis was the process limiting step, ceasing gas production when the HRT was shortened to 10 days. However, digestion with an HRT of 10 days was feasible after thermal pretreatment of the biosludge (20 min at 121 °C) due to enhanced hydrolysis. The methane yield was 78 NL CH4 kg(-1) VS for untreated biosludge and was increased by 77% (138 NL CH4 kg(-1) VS) after pretreatment., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Anaerobic digestion of alkaline kraft elemental chlorine-free bleaching wastewater in two mesophilic, lab-scale upflow anaerobic sludge bed reactors resulted in significantly higher biogas production (250±50 vs. 120±30 NmL g [Formula: see text]) and reduction of filtered total organic carbon (fTOC) (60±5 vs. 43±6%) for wastewater from processing of hardwood (HW) compared with softwood (SW). In all cases, the gas production was likely underestimated due to poor gas separation in the reactors. Despite changes in wastewater characteristics, a stable anaerobic process was maintained with hydraulic retention times (HRTs) between 7 and 14 h. Lowering the HRT (from 13.5 to 8.5 h) did not significantly affect the process, and the stable performance at 8.5 h leaves room for further decreases in HRT. The results show that this type of wastewater is suitable for a full-scale implementation, but the difference in methane potential between SW and HW is important to consider both regarding process dimensioning and biogas yield optimization.

The activated sludge process is an old technology, but still the most commonly used one for treatment of wastewater. Despite the wide spread usage the technology still suffers from instability (Tandoi et al. 2006) and high operating cost. Activated sludge processes often carry a large solids inventory. Managing the total inventory without interference is the key component of the optimization process described in this paper. Use of nutrients is common in pulp and paper effluent treatment. Feeding enough nutrients to support the biomass growth is a delicate balance. Overfeeding or underfeeding of nutrients can result in higher costs. Detrimental substances and toxic components in effluents entering a biological treatment system can cause severe, long lasting disturbances (Hynninen & Ingman 1998; Bergeron & Pelletier 2004). A LumiKem test kit is used to measure biological activity with adenosine triphosphate (ATP) in a pulp and paper mill. ATP data are integrated with other standardized mill parameters. Measurements of active volatile suspended solids based on ATP can be used to quantify the living biomass in the activated sludge process and to ensure that sufficient biomass is present in order to degrade the wastewater constituents entering the process. Information about active biomass will assist in optimizing sludge inventories and feeding of nutrients allowing the living biomass to re-populate to create optimal efficiency. ATP measurements can also be used to alert operators if any components toxic to bacteria are present in wastewater. The bio stress index represents the stress level experienced by the microbiological population. This parameter is very useful in monitoring toxicity in and around bioreactors. Results from the wastewater process optimization and ATP measurements showed that treatment cost could be reduced by approximately 20-30% with fewer disturbances and sustained biological activity compared to the reference period. This was mainly achieved by the removal of detrimental substances and optimized nutrient dosage.

Paper sludge is an attractive biomass source for the conversion to ethanol due to its low cost and the lack of severe pretreatment required. Four sludges from pulp and paper operations including both virgin kraft (VK) and recycled and deinking (RD) paper mills were analyzed. A fractionation process using a laboratory screen was utilized to produce a fiber-rich stream for enzymatic hydrolysis. This process removed 82-98 % of the ash with fiber yields from 39 to 69 %. Even though sludges in both non-fractionated and fractionated scenarios were pH-adjusted, total sugar conversion was still improved by 12-27 % by fractionation with 4.5 times less acid required for pH adjustment. Fermentation of the fractionated sludges showed very high ethanol yields. Acid insoluble clay adsorbs 3-5 mg enzyme per gram of clay depending on enzyme dosage. Acid soluble CaCO3 adsorbs about half of the enzyme compared to clay. Fractionation efficiency was also evaluated by testing different size mesh screen openings (100 to 500 mesh). The 400-mesh screen presented the best fiber yield, ash removal and ash fractionation ratio for both VK and RD sludges. The ash-rich streams have a lower C/N ratio than the original sludge which improves its suitability as soil amendment.

In this paper, the use of powered activated carbon (PAC) in membrane bioreactor (MBR) employed in the treatment of bleach pulp mill effluents was evaluated. The MBR was operated with hydraulic residence time of 9.5 h and PAC concentration of 10 g/L. The addition of PAC to the MBR reduced the average concentration of chemical oxygen demand (COD) in the permeate from 215 mg/L (82% removal efficiency) to 135 mg/L (88% removal efficiency), producing an effluent that can be reused on bleaching stage. Moreover, the addition of PAC to the MBR resulted in the reduction in applied pressure and provided a more stable operation during the monitoring period. This occurrence was probably due to the increase of critical flux after the addition of PAC. The fouling mechanism was investigated and the results showed that controlling the concentration of soluble microbial products (SMP) and extracellular polymeric substance (EPS) by using PAC and keeping the operational flux below critical flux is of major importance for MBR operational sustainability.

Bioethanol and enzymes were produced from fiber sludges through sequential microbial cultivations. After a first simultaneous saccharification and fermentation (SSF) with yeast, the bioethanol concentrations of sulfate and sulfite fiber sludges were 45.6 and 64.7 g/L, respectively. The second SSF, which included fresh fiber sludges and recycled yeast and enzymes from the first SSF, resulted in ethanol concentrations of 38.3 g/L for sulfate fiber sludge and 24.4 g/L for sulfite fiber sludge. Aspergillus niger carrying the endoglucanase-encoding Cel7B gene of Trichoderma reesei was grown in the spent fiber sludge hydrolysates. The cellulase activities obtained with spent hydrolysates of sulfate and sulfite fiber sludges were 2,700 and 2,900 nkat/mL, respectively. The high cellulase activities produced by using stillage and the significant ethanol concentrations produced in the second SSF suggest that onsite enzyme production and recycling of enzyme are realistic concepts that warrant further attention.

In this study, a series of experimental studies were conducted with regard to bioconversion of organic fraction of municipal solid waste along with paper mill sludge at different C/N ratios. About 10 kg of shredded waste containing paper mill sludge, saw dust and municipal solid waste was placed in reactors in different proportions and 100 mL of effective microorganisms was added to it. The variation in physical and chemical parameters was monitored throughout the process. The results indicate that co-composting of paper mill sludge with municipal solid waste produces compost that is more stable and homogenous and can be effectively used as soil conditioner.

A comparative study on the treatment of thermomechanical pulping (TMP) pressate was conducted under thermophilic (55 degrees C) and mesophilic (30 degrees C) temperatures to explore in-mill biological treatment, with the intention to operate under heat-efficient conditions. The experimental study involved sequencing batch reactors (SBRs) operated over 114 days. Receiving a total influent chemical oxygen demand (COD) of 3700-4100 mg L(-1), the COD removal efficiencies of 80-90% and 75-85% were achieved for the mesophilic and thermophilic SBRs, respectively, at a hydraulic retention time (HRT) of 12 and 24h. Excellent sludge settleability (sludge volume index < 100 mL g(-1) mixed liquor suspended solids) was obtained at both thermophilic and mesophilic SBRs. A higher level of effluent suspended solids was observed under thermophilic conditions. The results support the feasibility of applying thermophilic biological treatment of TMP pressate. The treated effluent has the potential for subsequent reuse as process water after polishing, thus addressing the long-standing desire to develop water system closure for the pulp and paper mill operation.

Start-up period is considered to be the most unstable and difficult stage in anaerobic process and usually takes a long time due to slow-degree adaptation of anaerobic microorganisms. In order to achieve a shorter start-up period, a novel modified anaerobic baffled reactor (MABR) has been developed in this study, where each modified baffle has its own characteristics (form/shape) to facilitate a treatment ofrecycled paper mill effluent (RPME). The results ofphysico-chemical characteristics showed that effluent from recycled paper mill consisted of 4328mgL-1 chemical oxygen demand (COD), 669mg L-1 biochemical oxygen demand and 501mg L-1 volatile fatty acid. It also consisted of variety of heavy metals such as zinc, magnesium, iron and nickel at concentrations of 1.39, 12.19, 2.39 and 0.72 mgL-1, respectively. Performance of MABR during the start-up period showed that methane production reached 34.7% with COD removal of 85% at steady state. The result indicates that MABR was successfully operated during the start-up period in treating RPME within a period of less than 30 days.

An on-line hybrid fuzzy-neural soft-sensing model-based control system was developed to optimize dissolved oxygen concentration in a bench-scale anaerobic/anoxic/oxic (A(2)/O) process. In order to improve the performance of the control system, a self-adapted fuzzy c-means clustering algorithm and adaptive network-based fuzzy inference system (ANFIS) models were employed. The proposed control system permits the on-line implementation of every operating strategy of the experimental system. A set of experiments involving variable hydraulic retention time (HRT), influent pH (pH), dissolved oxygen in the aerobic reactor (DO), and mixed-liquid return ratio (r) was carried out. Using the proposed system, the amount of COD in the effluent stabilized at the set-point and below. The improvement was achieved with optimum dissolved oxygen concentration because the performance of the treatment process was optimized using operating rules implemented in real time. The system allows various expert operational approaches to be deployed with the goal of minimizing organic substances in the outlet while using the minimum amount of energy.

The closure of water circuits within pulp and paper mills has resulted in a higher contamination load of the final mill effluent, which must consequently be further treated in many cases to meet the standards imposed by the legislation in force. Different treatment strategies based on advanced oxidation processes (ozonation and TiO2-photocatalysis), and their combination with biological treatment (MBR), are herein assessed for effluents of a recycled paper mill and a kraft pulp mill. Ozone treatment achieved the highest efficiency of all. The consumption of 2.4 g O3 L(-1) resulted in about a 60% COD reduction treating the effluent from the kraft pulp mill at an initial pH=7; although it only reached about a 35% COD removal for the effluent of the recycled paper mill. Otherwise, photocatalysis achieved about a 20-30% reduction of the COD for both type of effluents. In addition, the effluent from the recycled paper mill showed a higher biodegradability, so combinations of these AOPs with biological treatment were tested. As a result, photocatalysis did not report any significant COD reduction improvement whether being performed as pre- or post-treatment of the biological process; whereas the use of ozonation as post-biological treatment enhanced COD removal a further 10%, summing up a total 90% reduction of the COD for the combined treatment, as well as it also supposed an increase of the presence of volatile fatty acids, which might ultimately enable the resultant wastewater to be recirculated back to further biological treatment., (Copyright © 2013 Elsevier B.V. All rights reserved.)

In this study, the potential of a pilot-scale granular activated carbon sequencing batch biofilm reactor (GAC-SBBR) for removing chemical oxygen demand (COD), ammoniacal nitrogen (NH3-N) and 2,4-dichlorophenol (2,4-DCP) from recycled paper wastewater was assessed. For this purpose, the response surface methodology (RSM) was employed, using a central composite face-centred design (CCFD), to optimise three of the most important operating variables, i.e., hydraulic retention time (HRT), aeration rate (AR) and influent feed concentration (IFC), in the pilot-scale GAC-SBBR process for recycled paper wastewater treatment. Quadratic models were developed for the response variables, i.e., COD, NH3-N and 2,4-DCP removal, based on the high value (>0.9) of the coefficient of determination (R(2)) obtained from the analysis of variance (ANOVA). The optimal conditions were established at 750 mg COD/L IFC, 3.2 m(3)/min AR and 1 day HRT, corresponding to predicted COD, NH3-N and 2,4-DCP removal percentages of 94.8, 100 and 80.9%, respectively., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

Residues from forest-industry wastewater-treatment systems are treated as waste at many pulp and paper mills. These organic substances have previously been shown to have potential for production of large quantities of biogas. There is concern, however, that the process would require expensive equipment because of the slow degradation of these substances. Pure non-fibrous sludge from forest industry showed lower specific methane production during mesophilic digestion for 19days, 53±26 Nml/g of volatile solids as compared to municipal sewage sludge, 84±24 Nml/g of volatile solids. This paper explores the possibility of using anaerobic co-digestion with municipal sewage sludge to enhance the potential of methane production from secondary sludge from a pulp and paper mill. It was seen in a batch anaerobic-digestion operation of 19 days that the specific methane production remained largely the same for municipal sewage sludge when up to 50% of the volatile solids were replaced with forest-industry secondary sludge. It was also shown that the solid residue from anaerobic digestion of the forest-industry sludge should be of suitable quality to use for improving soil quality on lands that are not used for food production., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

The feasibility of anaerobic treatment of methanol condensate from pulp and paper mill in UASB reactor was investigated and compared with the anaerobic treatment of methanol. The UASB reactor treating methanol condensate was operated for 480 days with minimum problems of overload. COD removal from methanol condensate and methanol under normal operating conditions ranged from 84-86% to 86-98%, respectively. Under optimal conditions (OLR=5.0 g COD L(-1)day(-1), COD(influent)=11.40 g L(-1)) a methane yield of 0.29 NL CH(4) per g COD(removed) (at standard temperature and pressure) was achieved during the treatment of methanol condensate. The recovery time of the microorganisms after several overloads was decreasing each time probably due to the adaptation to methanol condensate. These findings indicate that methanol condensate can be efficiently treated in a UASB reactor with the benefit of biogas production. As a bonus effect of the treatment, much of the smell of the feed was eliminated., (Copyright © 2012. Published by Elsevier Ltd.)

This paper describes the results of laboratory experiments using a thermophilic aerobic MBR (TMBR) at 50 °C. An innovative use of submerged flat-sheet MBR modules to treat circuit wastewater from the paper industry was studied. Two experiments were conducted with a flux of 8-13 L/m(2)/h without chemical membrane cleaning. COD and BOD(5) elimination rates were 83% and 99%, respectively. Calcium was reduced from 110 to 180 mg/L in the inflow to 35-60 mg/L in the permeate. However, only negligible membrane scaling occurred. The observed sludge yield was very low and amounted to 0.07-0.29 g MLSS/g COD(eliminated). Consequently, the nutrient supply of ammonia and phosphate can be lower compared to a mesophilic process. Molecular-biological FISH analysis revealed a likewise high diversity of microorganisms in the TMBR compared to the mesophilic sludge used for start-up. Furthermore, ammonia-oxidising bacteria were detected at thermophilic operation., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

A novel integrated thermophilic submerged aerobic membrane bioreactor (TSAMBR) and electrochemical oxidation (EO) technology was developed for thermomechanical pulping pressate treatment with the aim of system closure. The TSAMBR was able to achieve a chemical oxygen demand (COD) removal efficiency of 88.6 ± 1.9-92.3 ± 0.7% under the organic loading rate of 2.76 ± 0.13-3.98 ± 0.23 kg COD/(m(3) d). An optimal hydraulic retention time (HRT) of 1.1 ± 0.1d was identified for COD removal. Cake formation was identified as the dominant mechanism of membrane fouling. The EO of the TSAMBR permeate was performed using a Ti/SnO(2)-Sb(2)O(5)-IrO(2) electrode. After 6-h EO, a complete decolourization was achieved and the COD removal efficiency was increased to 96.2 ± 1.2-98.2 ± 0.3%. The high-quality effluent produced by the TSAMBR-EO system can be reused as process water for system closure in pulp and paper mill., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Paper mill sludge (PMS) was utilized to prepare granular activated carbon (GAC) fillers for fluidized-bed bioreactor (FBBR) through stream activation. The properties of the PMS were tested and the optimum conditions for the production process were determined. Then, the GAC fillers were used in the FBBR to investigate the capacity for wastewater treatment. The results showed that the optimal conditions were: carbonization temperature of 450 degrees C, carbonization time of 50 min, activation temperature of 800 degrees C and activation time of 60 min. The specific surface area of the GAC fillers was 130 m2/g and the grain density was 1.34 x 10(3) kg/m3. The wastewater treatment results showed that after40 days ofrunning, under the conditions of influent COD of 800 mg/L and HRT of2 h, the COD removal efficiency was about 90%, which demonstrated that PMS-based GAC fillers were feasible for FBBR.

The types of treatment most commonly used by pulp mills are biological treatments in combination with sedimentation or coagulation/flocculation as pretreatment. The main issues faced by these types of treatment are low efficiency in the removal of organic matter and the loss of aggregate value for the recovered fiber. Therefore, this study aims to evaluate the use of microfiltration (MF) combined with a membrane bioreactor (MBR) for the treatment of bleach pulp mill effluents. The results showed that the use of the MF-MBR system was an excellent alternative for the treatment of bleach pulp mill effluents with an average COD removal of 95%. The microfiltration allowed the recovery of fibers, which can be returned to the production process without losing economic value, and produced a better quality effluent for further treatment in the MBR. The MBR presented high efficiency removal of organic matter.

A pilot scale granular activated carbon-sequencing batch biofilm reactor with a capacity of 2.2 m3 was operated for over three months to evaluate its performance treating real recycled paper industry wastewater under different operational conditions. In this study, dissolved air floatation (DAF) and clarifier effluents were used as influent sources of the pilot plant. During the course of the study, the reactor was able to biodegrade the contaminants in the incoming recycled paper mill wastewater in terms of chemical oxygen demand (COD), adsorbable organic halides (AOX; specifically 2,4-dichlorophenol (2,4-DCP)) and ammoniacal nitrogen (NH3-N) removal efficiencies at varying hydraulic retention times (HRTs) of 1-3 days, aeration rates (ARs) of 2.1-3.4 m3/min and influent feed concentration of 40-950 mg COD/l. Percentages of COD, 2,4-DCP and NH3-N removals increased with increasing HRT, resulting in more than 90% COD, 2,4-DCP and NH3-N removals at HRT values above two days. Degradation of COD, 2,4-DCP and NH3-N were seriously affected by variation of ARs, which resulted in significant decrease of COD, 2,4-DCP and NH3-N removals by decreasing ARs from 3.4 m3/min to 2.1 m3/min, varying in the ranges of 24-80%, 6-96% and 5-42%, respectively. In comparison to the clarifier effluent, the treatment performance of DAF effluent, containing high COD concentration, resulted in a higher COD removal of 82%. The use of diluted DAF effluent did not improve significantly the COD removal. Higher NH3-N removal efficiency of almost 100% was observed during operation after maintenance shutdown compared to normal operation, even at the same HRT of one day due to the higher dissolved oxygen concentrations (1-7 mg/l), while no significant difference in COD removal efficiency was observed.

The main objective of this study is to investigate the thermal profiles of a trailer-scale gasifier in different zones during the course of gasification and also to elaborate on the design, characteristics and performance of the gasification system using different biomass feedstock. The purpose is to emphasize on the effectiveness of distributed power generation systems and demonstrate the feasibility of such gasification systems in real world scenarios, where the lingo-cellulosic biomass resources are widely available and distributed across the board. Experimental data on the thermal profiles with respect to five different zones in the gasifier and a comprehensive thermal-chemical equilibrium model to predict the syngas composition are presented in detail. Four different feedstock-pine wood, horse manure, red oak, and cardboard were evaluated. The effects of C, H, O content variations in the feedstock on the thermal profiles, and the efficiency and viability of the trailer-scale gasifier are also discussed., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

This paper presents the design and operational performance data of an anaerobic/aerobic hybrid side-stream Membrane Bioreactor (MBR) process for treating paper mill effluent operated over a 6 month period. The paper mill effluent stream was characterized by a chemical oxygen demand (COD) range of between 1,600 and 4,400 mg/L and an average BOD of 2,400 mg/L. Despite large fluctuations in COD feed concentration, stable process performance was achieved. The anaerobic Expanded Granular Sludge Bed (EGSB) pre-treatment step effectively lowered the organic loading by 65 to 85%, thus lowering the MBR COD feed concentration to consistently below 750 mg/L. The overall MBR COD removal was consistent at an average of 96%, regardless of the effluent COD or changes in the hydraulic retention time (HRT) and organic loading rate (OLR). Combining a high-rate anaerobic pre-treatment EGSB with a Modified Ludzack-Ettinger (MLE) MBR process configuration produced a high quality permeate. Preliminary NF and RO results indicated an overall COD removal of around 97 and 98%, respectively.

Dark anaerobic fermentation is an interesting alternative method for producing biohydrogen (H(2)) as a renewable fuel because of its low cost and various usable organic substrates. Pulping sludge from wastewater treatment containing plentiful cellulosic substrate could be feasibly utilized for H(2) production by dark fermentation. The objective of this study was to investigate the optimal proportion of pulping sludge to paper waste, the optimal initial pH, and the optimal ratio of carbon and nitrogen (C/N) for H(2) production by anaerobic seed sludge pretreated with heat. The pulping sludge was pretreated with NaOH solution at high temperature and further hydrolyzed with crude cellulase. Pretreatment of the pulping sludge with 3% NaOH solution under autoclave at 121 °C for 2 h, hydrolysis with 5 FPU crude cellulase at 50 °C, and pH 4.8 for 24 h provided the highest reducing sugar production yield (229.68 ± 2.09 mg/g(TVS)). An initial pH of 6 and a C/N ratio of 40 were optimal conditions for H(2) production. Moreover, the supplement of paper waste in the pulping sludge enhanced the cumulative H(2) production yield. The continuous hydrogen production was further conducted in a glass reactor with nylon pieces as supporting media and the maximum hydrogen production yield was 151.70 ml/g(TVS).

Polyhydroxyalkanoate (PHA) biosynthesis in paper mill wastewater treated by a Moving Bed Biofilm Reactor (MBBR) was evaluated. A MBBR was operated during 300 d. The increasing effect of the Organic Load Rate (OLR) from 0.13 kg BOD(5)/m(3)·d to 2.99 kg BOD(5)/m(3)·d and the influence of two relationship of BOD(5:) N: P (100: 5: 1 and 100: 1: 0.3) on the PHA biosynthesis were evaluated. With an OLR of 0.13 kg BOD(5)/m(3)·d, the maximum organic matter removal measure as Biochemical Oxygen Demand (BOD(5)) was 98.7% for a BOD(5:) N: P relationship of 100: 5: 1. Meanwhile for BOD(5): N: P relationship of 100: 1: 0.3, the maximum efficiency was 87.2% (OLR: 2.99 kg BOD(5)/m(3)·d). The behaviour of the Chemical Oxygen Demand (COD) and total phenolic compound removal efficiencies were below 65.0% and 41.0%, respectively. PHA biosynthesis was measured as a percentage of cells that accumulate PHA, where the maximum percentage was 85.1% and 78.7% when MBBR was operated under a BOD(5): N: P relationship of 100: 5: 1 and 100: 1: 0.3, respectively. Finally, the PHA yields in this study were estimated to range between 0.11 to 0.72 mg PHA/mg VSS and 0.06 to 0.15 mg PHA/mg COD.

Properties improvement of paper mill sludge (PMS) based granular activated carbon fillers for fluidized-bed bioreactor (FBBR) was investigated in this study. Bentonite (Na) powders were blended in the dewatered paper mill sludge powders to strengthen the abrasion resistance strength of the fillers. Different acid washing treatments were studied to produce FBBR fillers with optimum performance. The results indicated that granulation was easy and the abrasion resistance strength of the fillers increased by 15% with 8 wt% of bentonite (Na) added. Acid washing treatment prior to activation had a better effect on the removal of Fe than post-activation acid washing treatment. HCl was the most appropriate acid during the acid washing treatment. The optimum acid washing treatment was carried out prior to activation with 2M HCl soaking for 6h. After acid washing treatment, the fillers with grain density of 1170 kg/m(3), specific surface area of 176 m(2)/g were obtained., (Copyright © 2011 Elsevier B.V. All rights reserved.)

The methane potential of activated sludge from six Swedish pulp and paper mills was evaluated. The methane production potential of sludge samples ranged from 100-200 NmL CH4 g(-1) volatile solids (VS) and for four of the six sludge samples the potential exceeded 170 NmL CH4 g(-1) VS. The effects of sludge age and dewatering on the methane production potential were evaluated. The effects of enzymatic and ultrasonic pre-treatment on the digestibility of sludge were also investigated, but energy or enzyme inputs in viable ranges did not exert a detectable, positive effect. Long-term, semi-continuous trials with sludge from two of the mills were also conducted in attempts to develop stable biogas production at loading rates up to 4 g VS L(-1). Cobalt addition (0.5 mg L(-1)) was here found to positively affect the turnover of acetate. High viscosity was a problem in all the experimental reactors and this limited the organic loading rate.

Effects of temperature and temperature shock on the performance and microbial community structure of a submerged anaerobic membrane bioreactor (SAnMBR) treating thermomechanical pulping pressate were studied for 416 days. The results showed that the SAnMBR system were highly resilient to temperature variations in terms of chemical oxygen demand (COD) removal. The residual COD in treated effluent was slightly higher at 55 °C than that at 37 and 45 °C. There were no significant changes in biogas production rate and biogas composition. However, temperature shocks resulted in an increase in biogas production temporarily. The SAnMBR could tolerate the 5 and 10 °C temperature shocks at 37 °C and the temperature variations from 37 to 45 °C. The temperature shock of 5 and 10 °C at 45 °C led to slight and significant disturbance of the performance, respectively. Temperature affected the richness and diversity of microbial populations., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

With increasing concerns over the limited capacity of landfills, conservation of resources, and reduction of CO(2) emissions, high-solids (dry) anaerobic digestion of organic solid waste (OSW) is attracting a great deal of attention these days. In the present work, two dry anaerobic co-digestion systems fed with different mixtures of OSW were continuously operated under mesophilic conditions. Dewatered sludge cake was used as a main seeding source. In reactor (I), which was fed with food waste (FW) and paper waste (PW), hydraulic retention time (HRT) and solid content were controlled to find the maximum treatability. At a fixed solid content of 30% total solids (TS), stable performance was maintained up to an HRT decrease to 40 d. However, the stable performance was not sustained at 30 d HRT, and hence, HRT was increased to 40 d again. In further operation, instead of decreasing HRT, solid content was increased to 40% TS, which was found to be a better option to increase the treatability. The biogas production rate (BPR), CH(4) production yield (MPY) and VS reduction achieved in this condition were 5.0m(3)/m(3)/d, 0.25 m(3) CH(4)/g COD(added), and 80%, respectively. Reactor (II) was fed with FW and livestock waste (LW), and LW content was increased during the operation. Until a 40% LW content increase, reactor (II) exhibited a stable performance. A BPR of 1.7 m(3)/m(3)/d, MPY of 0.26 m(3) CH(4)/g COD(added), and VS reduction of 72% was achieved at 40% LW content. However, when the LW content was increased to 60%, there was a significant performance drop, which was attributed to free ammonia inhibition. The performances in these two reactors were comparable to the ones achieved in the conventional wet digestion and thermophilic dry digestion processes., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

The ability of two natural phenols to act as mediators of the recombinant Myceliophthora thermophila laccase (MtL) in eucalypt-pulp delignification was investigated. After alkaline peroxide extraction, the properties of the enzymatically-treated pulps improved with respect to the control. The pulp brightness increased (3.1 points) after the enzymatic treatment with MtL alone, but the highest improvements were obtained after the MtL treatment using syringaldehyde (4.7 points) and especially methyl syringate (8.3 points) as mediators. Likewise, a decrease in kappa number up to 2.7 points was obtained after the MtL-methyl syringate treatment, followed by decreases of 1.4 and 0.9 points after the treatments with MtL-syringaldehyde and MtL alone, respectively. On the other hand, removal of the main lipophilic extractives present in eucalypt pulp was observed after the above laccase-mediator treatments. Finally, the doses of both MtL and methyl syringate were reduced, and results compatible with industrial implementation were obtained., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

Background, Aim, and Scope: For many years, highly concentrated wastewater generated from the pulp and paper industry has become the focus of much concern worldwide. The objectives of this study were to determine the treatment efficiency of the alkaline peroxide mechanical pulp (APMP) process wastewater using a sequencing batch reactor (SBR) and analyze the microbial dynamics of the wastewater treatment system using the random amplified polymorphic DNA (RAPD) method., Materials and Methods: An SBR was applied to the treatment of APMP pulp and paper process wastewater. The wastewater characteristics and many physicochemical operator indicators in the wastewater treatment process were analyzed and determined according to standard methods. Microbial 16 S rDNA in active sludge was extracted, amplified, and analyzed using the RAPD method for the microbial dynamics of the wastewater treatment system., Results and Discussion: Ten kinds of natural organic compounds of plants such as monoterpene were detected in the APMP pulp and paper process wastewater. With an influent chemical oxygen demand (COD) that varied in the range of 685.7 to 907.5 mg/L, the corresponding effluent COD was 176.5 to 266.1 mg/L and the removal efficiency was 70.3% to 79.8%. An optimal strain (S308: CAGGGGTGGA) was selected to study the population dynamics and diversity of the bacterial community. The RAPD-polymerase chain reaction (PCR) fingerprints showed very high polymorphism of the genetic bands (78-100%). Four groups of species were clustered using the unweighted pair group method with arithmetic (UPGMA) analysis, and the genetic distance was close between the species within each group. The Shannon-Weaver index was high and varied over time with the COD removal., Conclusions: The RAPD-PCR technique can be used to study microbial dynamics, which was shown to vary over time with the removal efficiency of SBR treating APMP pulp and paper process wastewater.

The absence of a systematic scale-up approach for biological conversion of cellulosic biomass to commodity products is a significant bottleneck to realizing the potential benefits offered by such conversion. Motivated by this, we undertook to develop a scale-up approach for conversion of waste paper sludge to ethanol. Physical properties of the system were measured and correlations were developed for their dependence upon cellulose conversion. Just-suspension of solid particles was identified as the scale up criterion based on experiments at lab scale. The impeller speed for just solids suspension at large scale was predicted using computational fluid dynamics simulations. The scale-up strategy was validated by analyzing mixing requirements such as solid-liquid mass transfer under the predicted level of agitation at large scale. The scale-up approach enhances the prediction of reactor performance and helps provide guidelines for the analysis and design of large scale bioreactors based on bench scale experimentation.

Pulp and paper mills are under increasing pressure to minimize the discharge of phosphate to receiving waters. We investigated the operation of two laboratory sequencing batch reactors (SBR) under low phosphate conditions over a period of eight months. Performance characteristics in terms of COD and TSS removal were similar to the full-scale mill activated sludge operation, but the floc density and structure was improved. Sludge yield as a result of phosphate limitation was routinely lower than 0.15 kg/kg of COD. Aerobic granule formation was established in one of the SBRs by reducing the settling time from 30 min to 2 min and by increasing stirring shear force. Once established, the brown granules which were 1-2 mm in diameter were stable over five months of operation. Extracellular polymeric substance (EPS) analysis of the granules indicated a higher galactose content and lower mannose content than in conventional flocs. The granules generated more quorum sensing compound (acyl homoserine lactone) than conventional flocs, suggesting that quorum sensing could play a role in granule formation. When compared to the conventional SBR, the aerobic granule SBR performed at a higher organic loading, at faster settling velocity, and without filamentous bulking.

A paper mill producing 500,000 ton of graphic paper annually has an on-site wastewater treatment plant that treats 7,240,000 m³ of wastewater per year, mechanically first, then biologically and at last by ozonation. Increased paper production capacity led to higher COD load in the mill effluent while production of higher proportions of brighter products gave worse biodegradability. Therefore the biological capacity of the WWTP needed to be increased and extra measures were necessary to enhance the efficiency of COD reduction. The full scale implementation of one MBBR with a volume of 1,230 m³ was accomplished in 2000 followed by another MBBR of 2,475 m³ in 2002. An ozonation step with a capacity of 75 kg O₃/h was added in 2004 to meet higher COD reduction demands during the production of brighter products and thus keeping the given outflow limits. Adding a moving bed biofilm reactor prior to the existing activated sludge step gives: (i) cost advantages when increasing biological capacity as higher COD volume loads of MBBRs allow smaller reactors than usual for activated sludge plants; (ii) a relief of strain from the activated sludge step by biological degradation in the MBBR; (iii) equalizing of peaks in the COD load and toxic effects before affecting the activated sludge step; (iv) a stable volume sludge index below 100 ml/g in combination with an optimization of the activated sludge step allows good sludge separation--an important condition for further treatment with ozone. Ozonation and subsequent bio-filtration pre-treated waste water provide: (i) reduction of hard COD unobtainable by conventional treatment; (ii) controllable COD reduction in a very wide range and therefore elimination of COD-peaks; (iii) reduction of treatment costs by combination of ozonation and subsequent bio-filtration; (iv) decrease of the color in the ozonated wastewater. The MBBR step proved very simple to operate as part of the biological treatment. Excellent control of the COD-removal rate in the ozone step allowed for economical usage and therefore acceptable operation costs in relation to the paper production.

In-mill thermophilic treatment of individual wastewater streams to achieve water system closure has received much attention in pulp and paper mills. Aerobic biological treatment of thermomechanical pulping (TMP) condensate was conducted using thermophilic (55 °C) and mesophilic (35 °C) sequencing batch reactors (SBRs) for a period of 143 days at a cyclic time of 6, 8 and 12 h. A soluble chemical oxygen demand (SCOD) removal efficiency of 77 to 91% was achieved, given an organic loading rate of 0.7-1.3 kg/m³ d. The COD removal efficiency of the thermophilic SBR was slightly lower than that of the mesophilic SBR. Majority of the soluble COD was removed by biodegradation with a small portion (9-13%) of soluble COD stripped by aeration. The settleability (sludge volume index) and the flocculating ability (effluent suspended solids) of thermophilic sludge were comparable to or slightly poorer than that of the mesophilic sludge. The level of filaments in thermophilic sludge was usually higher than that in mesophilic sludge. The results of the study indicate that both thermophilic and mesophilic SBRs can be successfully operated for in-mill treatment of TMP condensate. The treated effluent has the potential for subsequent reuse in the mill.

The Rayon grade pulp (RGP) drain effluent of pulp and paper mill was studied to find out pollutant loading and its control measures by low cost and efficient treatment method. Upflow anaerobic fixed packed bed reactor (UAFPBR) with brick ballasts as packing material was used for this purpose. This was compared with conventional anaerobic treatment method. The digested slurry was taken as inoculum from the active cow dung biogas plant. After stabilization of the reactors the reduction in pollutant loading was found to be higher in UAFPBR than conventional anaerobic reactor (CAR). Hydraulic retention time (HRT) of 12 hr was optimum for the treatment of effluent when 74.5% COD and 81% BOD reduction was obtained. 30% inoculum concentration was best for the anaerobic treatment of RGP colour drain effluent. The maximum biogas production (1.37 l l(-1) of effluent) was when the effluent was inoculated with 30% seeding material. Thus, UAFPBR system was very efficient in terms of BOD, COD, TSS and TDS removal from RGP drain of paper mills in ambient environmental conditions.

The purpose of this study was to assess the anaerobic degradation of black liquor with and without additional carbon sources. Batch experiments were conducted using black liquor, from an integrated pulp and paper mill adding ethanol, methanol and nutrients. The PCR/DGGE technique was used to characterize the structure of the microbial community. The addition of extra sources of carbon did not significantly influence the degradation of black liquor under the conditions evaluated and the microbial community was similar in all experiments. It was observed an increase in some members of the archaeal in reactors that had the best efficiencies for removal of black liquor (around 7.5%). Either ethanol or methanol can be used as co-substrates because the produce the same quantitative and qualitative effect.

A Moving Bed Bioreactor (MBBR) was operated during 333 days. Two different effluents were fed in six different phases. Phases I and II were fed with effluent where Pinus radiata was used as raw material, while phases III to VI were fed with effluent where Eucalyptus globulus was used as raw material. The HRT was reduced from 85 to 4 h, and the BOD(5):N:P ratio (100:5:1, 100:3:1 and 100:1:1) was also simultaneously evaluated as an operation strategy. When MBBR was operated with Pinus radiata influent, the performance presents a high BOD(5) removal level (above 95%), although COD removal is below 60%. Most of the recalcitrant COD contained in the effluent has a molecular weight higher than 10,000 Da. When MBBR was operated with Eucalyptus globulus influent, the performance is around 97.9-97.6% and 68.6-65.1% for BOD(5) and COD, respectively (with HRT up to 17 h). In the Pinus radiata and Eucalyptus globus effluents, the color was mainly found in the molecular weight fraction up to 10,000 Daltons.