Search

In this work an environmentally friendly hydrotropic process was used to extract lignin from industrial birch wood chips. Two hydrotropic treatments were performed, a conventional and a modified process. The lignins were characterized using FTIR, pyrolysis-gas chromatography-mass spectrometry (pyrolysis-GC-MS), (31)P and (1)H-(13)C HSQC NMR, and size exclusion chromatography (SEC). The chemical (carbohydrates, extractives, etc.) and elemental compositions of the lignins were also determined. The yields of both lignins were 16.1% (dry wood basis), and the obtained lignins had very low contents of non-lignin compounds. The treatments resulted in significant changes of the structure of the lignins, a decrease in aliphatic hydroxyls and an increase in phenolic ones. The lignin isolated by the modified treatment underwent more substantial change than the reference one. It is believed that the data presented will facilitate utilization of hydrotropic lignin and promote the adoption of the hydrotropic process in the pulp and biorefinery industry.

A portion of hemicelluloses and acetic acid can be pre-extracted with dilute sulfuric acid prior to the aspen chemithermomechanical pulp process. The streams collected from the second press-impregnation stage after acid pre-extraction contain a significant amount of acid pre-extracted hemicelluloses. Most of the total sugars obtained from the pressate were xylan, in which xylan was further hydrolyzed to sugar monomers under the acid pre-extraction condition. To fully understand the characteristics of hemicelluloses yielded prior to pulping, the pre-extracted hemicelluloses were separated and characterized by FT-IR, (1)H NMR, and thermogravimetric analysis in this study. Most of the FT-IR bonds from the hemicelluloses agreed well with the other two spectra of birch xylan and CA0050 xylan, except a new absorption at 1734 cm(-1) contributed to acetyl groups. The hemicelluloses obtained from acid pre-extraction began to decompose significantly at about 225 °C, slightly lower in comparison with organosolv and alkaline hemicelluloses reported in the literature.

A quantitative approach to characterize lignin-carbohydrate complex (LCC) linkages using a combination of quantitative ¹³C NMR and HSQC 2D NMR techniques has been developed. Crude milled wood lignin (MWLc), LCC extracted from MWLc with acetic acid (LCC-AcOH) and cellulolytic enzyme lignin (CEL) preparations were isolated from loblolly pine (Pinus taeda) and white birch (Betula pendula) woods and characterized using this methodology on a routine 300 MHz NMR spectrometer and on a 950 MHz spectrometer equipped with a cryogenic probe. Structural variations in the pine and birch LCC preparations of different types (MWL, CEL and LCC-AcOH) were elucidated. The use of the high field NMR spectrometer equipped with the cryogenic probe resulted in a remarkable improvement in the resolution of the LCC signals and, therefore, is of primary importance for an accurate quantification of LCC linkages. The preparations investigated showed the presence of different amounts of benzyl ether, γ-ester and phenyl glycoside LCC bonds. Benzyl ester moieties were not detected. Pine LCC-AcOH and birch MWLc preparations were preferable for the analysis of phenyl glycoside and ester LCC linkages in pine and birch, correspondingly, whereas CEL preparations were the best to study benzyl ether LCC structures. The data obtained indicate that pinewood contains higher amounts of benzyl ether LCC linkages, but lower amounts of phenyl glycoside and γ-ester LCC moieties as compared to birch wood.

O-acetylated glucomannans were isolated from aspen and birch wood employing two different procedures and thereafter subjected to carbohydrate analysis by NMR spectroscopy and MALDI mass spectrometry. In one of the isolation procedures, acetone-extracted aspen or birch wood meal was extracted with dimethyl sulfoxide and then with hot water. Fractionation of the hemicellulose-containing extracts by size-exclusion chromatography was subsequently performed. In the other procedure, fractional precipitation with ethanol was used to isolate glucomannans from lyophilized process water produced by mechanical pulping of aspen. The aspen and birch glucomannans are O-acetylated at the C-2 or C-3 position of some of the mannose residues (random distribution), with a degree of acetylation of approx 0.3. In both cases the degree of polymerization was approx 16, indicating that low-molecular mass fractions of the glucomannans in hardwood have been isolated here.

The structures of water-soluble birch and beech xylans, extracted from holocellulose using dimethyl sulfoxide, were determined employing 1H and 13C NMR spectroscopy together with chemical analysis. These polysaccharides were found to be O-acetyl-(4-O-methylglucurono)xylans containing one 4-O-methylglucuronic acid substituent for approximately every 15 D-xylose residues. The average degree of acetylation of the xylose residues in these polymers was 0.4. The presence of the structural element -->4)[4-O-Me-alpha-D-GlcpA-(1-->2)][3-O-Ac]-beta-D-Xylp-(1--> was demonstrated. Additional acetyl groups were present as substituents at C-2 and/or C-3 of the xylopyranosyl residues. Utilizing size-exclusion chromatography in combination with mass spectroscopy, the weight-average molar masses (and polydispersities) were shown to be 8000 (1.09) and 11,100 (1.08) for birch and beech xylan, respectively.