Search

A cost-effective and accurate method for predicting over-the-air (OTA) data throughput of multiple-input and multiple-output (MIMO) wireless devices in the antenna design stage is proposed. The method incorporates passive characteristics of MIMO antennas, realistic channel model, and conductive measurement results in a computer simulation framework. With extracted relation between received power and signal-to-noise ratio (SNR) of a wireless device at antenna ports by a conductive test and measured passive characteristics of MIMO antennas, OTA throughput versus received power in a realistic channel model is obtained by the Monte Carlo simulation of Shannon’s law. The unique features of this method include: no channel emulator equipment is required; a wide variety of precoding schemes can be applied; passive characteristics of antennas are fully incorporated; and frequency-selective fading channel can be adopted. The method has been intensively validated by comparing the calculated OTA throughputs with those measured by a multiprobe anechoic chamber method under spatial channel model extension (SCME) in three aspects: spatial correlation, radiation efficiency, and mutual coupling, showing as low as 0.2–0.3 dB discrepancy in power level in most cases. The method can be used to evaluate a MIMO array antenna design of a wireless device with respect to OTA performance. [ABSTRACT FROM AUTHOR]

In this article, H-plane cross-polarization (X-pol) radiation of probe-fed air-filled patch antennas is substantially suppressed by introducing two or more floating metal cylinders underneath the patch, respectively. The X-pol is canceled by the radiation of induced currents on metal cylinders. The working principle of the new X-pol suppressed patch (XSP) antenna is revealed by an approximate model. The X-pol level of a typical XSP antenna can be suppressed to lower than −49 and −37 dB theoretically and experimentally for $| \theta |\le 60^{\circ }$. Two $1\times $ 8-element arrays constructed by XSP antennas and conventional patch antennas are prototyped and measured at scanning beam angles of $\theta = 0^{\circ }$ , −40°, and −65°. The measured co-polarization (co-pol) gain of the XSP antenna array is 0.7 and 0.9 dB larger than that of the conventional patch array at $\theta = -40^{\circ }$ and −65°, respectively. Besides, the beam scanning angle with −30 dB X-pol level of the XSP antenna array can be as wide as $| \theta |\le 40^{\circ }$ , while that of the conventional patch array is about $| \theta |\le 12^{\circ }$. A wide-band dual-polarized XSP antenna is also presented. The measured maximum H-plane X-pol level can be lower than −29 dB within 8.7% fractional bandwidth. [ABSTRACT FROM AUTHOR]

This article proposes and presents a fully planar endfire circularly polarized (CP) antenna with mingled three-layer substrates. It consists of a unidirectional dielectric radiator (UDR) and an antipodal linearly tapered slot antenna (ALTSA) surrounded by a UDR. The ALTSA is fed by a substrate integrated waveguide (SIW) on a thin substrate of $0.05\lambda _{0}$ , which can easily be integrated with RF subsystems. The UDR is fed by the ALTSA, which enables the UDR to enhance the original vertically polarized radiation rather than the horizontally polarized radiation from the ALTSA. Due to the polarization selectivity enhancement, an endfire CP antenna with a very thin substrate is created. An experimental prototype of the proposed antenna has been studied, designed, and measured. The measured impedance bandwidth of −10 dB covers a broadband of 29.7 GHz from 26.1 to 55.8 GHz, and the 3 dB AR bandwidth is 19.7 GHz ranging from 25.3 to 45 GHz. The measured gain is over 9 dBic from 27.8 GHz to over 32 GHz. A good performance with a small size of only $2.57\lambda _{0} \times 0.78\lambda _{0} \times 0.33\lambda _{0}$ , including the CPW-SIW transition, makes it an attractive option in the development of high gain planar endfire CP antennas and arrays for 5G and B5G applications. [ABSTRACT FROM AUTHOR]

The concept of a self-decoupled antenna array using the cancellation of two opposite couplings is proposed in this article. A pair of such antennas can be closely placed with inherent high isolation without using an extra decoupling structure between the antennas. A pertinent equivalent circuit model is presented to illustrate the physical mechanism of this new concept. It is found that the inductive and capacitive couplings between the antennas can be well canceled out with each other by properly adjusting the antenna dimensions. A demonstrating antenna array with a spacing of $0.024\lambda _{0}$ at the working frequency of 3.5 GHz and its counterpart array are first studied. The measured results show that although the proposed antenna array occupies a slightly larger size than its counterpart array, it presents better performance compared with its counterpart antenna array in port isolation (from 10 to 20 dB), total efficiency (from 68% to 80%), and envelope correlation coefficient (ECC) (from 0.14 to 0.04) throughout the desired frequency band of 3.3–3.8 GHz. A 3-D self-decoupled antenna array is designed to show that the proposed antenna can be in a compact form factor. Another self-decoupled array and its counterpart working at 2.14 GHz (long-term evolution (LTE) band 1) are studied through multi-input multi-output (MIMO) over-the-air (OTA) test when the arrays are integrated with an LTE module, showing significant improvement on the data throughput. [ABSTRACT FROM AUTHOR]

A new wideband ±45° dual-polarized metal loop dielectric resonator magnetoelectric antenna is proposed in this communication. The antenna consists of two orthogonal dielectric bars that support two orthogonal electric dipoles and two cross interlaced metal semi-loops that are equivalent to two orthogonal magnetic dipoles above the ground. With a legitimate combination of the electric and magnetic dipoles, a unidirectional radiation with low backward radiation and equal E-plane and H-plane radiation patterns can be achieved. The antenna can be made of a monolithic dielectric block with simple installation. To validate the new antenna configuration, a prototype is designed, manufactured, and measured. The prototype antenna using ceramic with the electrical size of $0.33\lambda _{o} \times 0.33\lambda _{o} \times 0.21\lambda _{o}$ demonstrates that an impedance bandwidth of 11.4% ($\vert S_{11}\vert < -15$ dB) in the 3.5 GHz frequency band can be achieved with the measured forward/backward ratio of better than 22 dB. The proposed antenna is suitable as antenna element for massive-MIMO array antennas, where a large number of antenna elements need to be installed in a compact space. [ABSTRACT FROM AUTHOR]

Unlike popular multiband antenna array radiation based on either electric or magnetic surface currents, the use of mutually interleaved and tightly coupled electric and magnetic currents results in an aperture-reuse space-efficient multiband radiating surface for highly integrated antenna-frontend architecture and spatial power combining design scenarios. In this work, slot and dipole modes corresponding to magnetic and electric currents are effectively interleaved and excited in a surface to develop a space-efficient dual-wideband aperture-shared radiating surface. In this case, due to an effective reuse of the antenna aperture over both frequency bands, a high aperture-reuse efficiency is achieved. First, we devise a planar magneto-electric (ME)-dipole-alike antenna and analyze it in both the frequency and time domain. The antenna is then studied by the characteristic mode theory and the findings are validated using full-wave simulations. The developed planar ME-dipole-alike antenna is used to realize a dual-wideband radiating surface in which electric and magnetic currents are mutually coupled and interlaced, which is excited by properly oriented and distributed sources on the antenna's surface. Eventually, a highly isolated dual-wideband prototype was developed and fabricated using a cost-effective multi-layer Printed Circuit Board (PCB) process that operates in the Ku-band with both impedance and gain bandwidth of approximately 42% and in the Ka-band with respective impedance and gain bandwidth of 29% and 16.32%. [ABSTRACT FROM AUTHOR]

A decoupling technique for a symmetric four-element compact array is proposed. A dummy array terminated with optimum reactive loads is introduced to cancel the mutual couplings between the four radiating elements. A theory that leads to a general design procedure is developed. The technique is demonstrated by three practical design examples, including a compact and low-profile “cheese-cake” antenna array. Calculated channel capacities demonstrate that the performance of a 4-by-4 MIMO communication system that uses the cheese-cake array can be significantly improved as compared to the system using its coupled counterpart. This technique provides a promising approach to the design of a compact four-element array for a MIMO communication system. [ABSTRACT FROM PUBLISHER]

A novel configuration of millimeter-wave planar array antenna based on low-temperature cofired ceramic (LTCC) technology is investigated. The configuration exploits the three-dimensional (3-D) integration feature of LTCC by incorporating a novel quasi-cavity-backed patch (QCBP) element using a pair of grid-like conductor walls and a mixed feeding network configuration. A proposed LTCC planar array antenna consisting of 16 by 16 elements is designed, manufactured and tested. Good agreement is achieved between the theoretical performance and the measured results. [ABSTRACT FROM AUTHOR]

In this article, a densely integrated and unified paralleled amplifier and antenna architecture is proposed and demonstrated for next-generation millimeter-wave (mmW) and terahertz (THz) front-end modules. It makes use of topologically paralleled transistors cohabitated within a compact rectangular patch antenna (CRPA) as a unified cell. This design simultaneously amplifies and radiates power without resorting to any power divider, input and output matching networks, or power combiner whatsoever, therefore, greatly reducing front-end loss, size, and complexity. Then, the unified unit cell is self-consistently distributed to form a unified planar array with active elements between array elements as power feeders. In this demonstration, the input power is sequentially amplified, radiated through each array element, and spatially added up, resulting in low on-board circuit losses and efficient radiation. In this article, we investigate and present challenges and early results of implementing this unification concept of active circuitry and antenna at mmW frequencies. Using a standard 65-nm CMOS process, a set of chips were designed, fabricated, and tested under different amplifier biasing conditions at 146 GHz for experimental demonstration. The realized low-loss, matched, and compact unified prototypes have demonstrated an amplified radiation, with power enhancement of 3.4 dB through single element and 6 dB through $2 \times 2$ layout compared to their respective passive counterparts. Moreover, frequency tuning is observed varying drain bias and self-matching is improved with increasing gate bias. Therefore, the feasibility of a unique feature in the architectural implementation of low-loss, compact, and densely integrated and topologically cohabitated mmW and THz front-end modules is confirmed. [ABSTRACT FROM AUTHOR]

Loading effects of radiating discontinuities have been explored to increase the phase constant’ frequency sensitivity of leaky-wave antennas (LWAs), based on which a quasi-uniform transversely slotted substrate integrated waveguide LWA featuring rapid beam-scanning and its hexagonal array have been proposed and investigated for millimeter-wave applications. The design concept is simply based on the use of a short period of unit cells and a long transverse slot with a sharp inductive reactance, and it has been theoretically elaborated and effectively validated by both full-wave and circuit-based simulations. A taper design with −25 dB Taylor amplitude distribution is implemented for the proposed LWA to have a low sidelobe radiation. For practical system applications, a hexagonal array consisting of six proposed LWAs is developed to provide an omnidirectional coverage in the azimuth plane while remaining the rapid frequency-driven beam-scanning in the elevation plane. Both the measured and simulated results are in an acceptable agreement with respect to the LWA block and the associated hexagonal array in terms of circuit and radiation performances. The proposed antenna will be a good candidate to be applied for prospective millimeter-wave systems such as autonomous driving and flying. [ABSTRACT FROM AUTHOR]

This communication presents a high-order-mode microstrip patch antenna driven by substrate integrated waveguide (SIW) for millimeter-wave polarization-adjustable applications. Different polarization status can be yielded from variable excited signals, including vertical and horizontal linear, right-handed and left-handed circular polarizations. In the patch antenna configuration, an enlarged aperture coming from high-order mode makes it easy to be fed by orthogonal SIWs for dual polarizations. Loaded slots on the patch significantly improve the radiation patterns. The impedance bandwidth with dual resonances is originated from the SIW slot and patch modes. A Ka-band $2\times 2$ antenna array integrated with single-layer SIW feeding network is designed and tested to illustrate this technique. The results manifest that the planar integrated $2 \times 2$ antenna array features adjustable polarization with considerable gain. Furthermore, a two-layer scheme of orthogonal SIW feeding is developed, which would provide a more flexible topology for the scale-expandable array antenna with adjustable polarizations. [ABSTRACT FROM AUTHOR]

An integrated low-temperature co-fired ceramic (LTCC) coupled resonator decoupling network (CRDN) for two coupled antennas is proposed in this paper. By virtue of LTCC technology, a second-order CRDN is realized by two tightly coupled lumped-element resonators in a volume of \3.2\times \2.5\times \1.2\ \mm^3. Theoretical analysis has revealed that a wide range of mutual admittance of a CRDN can be realized by choosing appropriate I/O coupling elements while the coupled resonators can be consolidated in an LTCC device. This “one-fit-all” feature allows for decoupling a wide range of coupled antennas with different form factors for a given frequency band. To prove the concept, two LTCC CRDNs for decoupling different forms of antennas working in the 2.45-GHz band are designed, fabricated, and tested. Measurement results have demonstrated that significant improvement in isolation can be achieved within a wide operating frequency range in all cases. The presented design theory and circuit topology are general and can be applied to both symmetric and asymmetric two-element antenna arrays. [ABSTRACT FROM PUBLISHER]

The gain bandwidth constraint of sequential-rotation arrays (SRAs) has been an open issue since it was first pointed out in 1989. This paper reveals the reason, provides some useful conclusions and proposes an optimum design. Firstly, a first-order analytical formula is derived for the array factor (AF) of the 4-element sub-SRA. The formula embraces the polarization properties of the antenna elements. The AF is found to be dependent on the elements' polarization properties and frequency, which is not found in conventional regular arrays. Based on the theoretical results and full-wave simulations, these dependencies are analyzed in detail. Secondly, an optimum design is proposed to enhance the gain bandwidth: to constitute SRA with elliptically polarized elements (this type of SRA is denoted as EP-SRA) rather than the conventional circularly polarized elements (this type of SRA is denoted as CP-SRA). Detailed design guidance is presented for this new method. Finally, as an example, a CP-SRA and an EP-SRA are designed and tested for comparison. According to the example, by employing EP-SRA, the 1 dB AF bandwidth is improved by 80%, the measured 1 dB/3 dB gain bandwidth is enhanced by 114%/76%. In fact, the conventional CP-SRA and LP-SRA (SRA with linearly polarized elements) are two special cases of the proposed EP-SRA. [ABSTRACT FROM PUBLISHER]

A class of three-dimensional planar arrays in substrate integrated waveguide (SIW) technology is proposed, designed and demonstrated with 8 \times 16 elements at 35 GHz for millimeter-wave imaging radar system applications. Endfire element is generally chosen to ensure initial high gain and broadband characteristics for the array. Fermi-TSA (tapered slot antenna) structure is used as element to reduce the beamwidth. Corrugation is introduced to reduce the resulting antenna physical width without degradation of performance. The achieved measured gain in our demonstration is about 18.4 dBi. A taper shaped air gap in the center is created to reduce the coupling between two adjacent elements. An SIW H-to-E-plane vertical interconnect is proposed in this three-dimensional architecture and optimized to connect eight 1 \times 16 planar array sheets to the 1 \times 8 final network. The overall architecture is exclusively fabricated by the conventional PCB process. Thus, the developed SIW feeder leads to a significant reduction in both weight and cost, compared to the metallic waveguide-based counterpart. A complete antenna structure is designed and fabricated. The planar array ensures a gain of 27 dBi with low SLL of 26 dB and beamwidth as narrow as 5.15 degrees in the E-plane and 6.20 degrees in the 45^\circ-plane. [ABSTRACT FROM PUBLISHER]

A novel bandwidth enhancement technique for phase-reversal Franklin-type antennas is proposed. Impedance bandwidth enhancement is achieved by combining several coupled modes of the antenna structure through periodic loading provided by radiating crossover dipoles. This technique is explained by the theory of periodically loaded transmission lines. Radiation pattern bandwidth enhancement is achieved by exciting the antenna in its center so as to suppress beam squinting by superposing the tilted beams of two resulting sub-arrays on either side of the feed. An offset parallel stripline (OPS) phase-reversal antenna using these bandwidth enhancement techniques is demonstrated theoretically and experimentally at 35 GHz. The antenna is printed on a thin substrate suspended over a micro-machined conductor-backed cavity for unidirectional radiation. The overall fractional bandwidth of the antenna is increased from 3% to over 11% compared to the conventional design and the antenna efficiency exceeds 80%. [ABSTRACT FROM AUTHOR]

A new phased-array driver module for a two-antenna array is proposed in this paper. This driver, designed using a six-port phase discriminator, automatically controls the phase of one antenna-array element in order to maximize the received power. The results for a phased two-antenna array operating at 2.45 GHz are presented and discussed. © 2005 Wiley Periodicals, Inc. Microwave Opt Technol Lett 46: 346–349, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.20983 [ABSTRACT FROM AUTHOR]