Search

The eight-chain RF system and radio frequency quadrupole (RFQ) linac were successfully integrated at the facility of the Linear IFMIF Prototype Accelerator (LIPAc). We achieved an unprecedented high current deuteron beam up to 55 mA in pulse operation ( $300~\mu \text{s}$ , 1 Hz). The keys of the success were (1) understanding reflected power from RFQ to RF system, (2) tuning each RF chain individually, (3) intensive RF conditioning for holding the stable RF power in the RFQ, and (4) optimizing the beam loading compensation control. Interestingly, the reflection at the breakdown in RF conditioning was higher than an estimation and reached up to 600 kW so far. In order to avoid damage on tetrodes by the high reflection, the impedance of each circulator was accurately adjusted.

The detailed shielding analysis has been performed in order to find a configuration of the radiation shielding in the accelerator building necessary for the operation of the Linear IFMIF Prototype Accelerator (LIPAc), which is under construction in Rokkasho, Japan, at the full power of 1.125 MW to satisfy the radiation dose limit prescribed by Japanese regulations. The final design of the beam dump constructed by CIEMAT, Spain was fully taken into consideration. The impact of all the features potentially causing neutron streaming were investigated and the optimization of local additional shieldings were conducted. As the result, the most important one was found to be the air ventilation duct shield, which completely covers the ducts and creates an additional labyrinth. By considering the additional shielding configuration determined in the present study, the legal criteria at the controlled area boundary can be completely satisfied.

International audience; Design, development, manufacturing, and test activities of the RF power system (RFPS) for Linear IFMIF Prototype Accelerator (LIPAc) were completed in Europe. Installation and commissioning activities were carried out at the International Fusion Materials Irradiation Facility-Engineering Validation and Engineering Design Activities (IFMIF/EVEDA) site in Rokkasho, Japan. Challenging IFMIF requirements led to a number of innovations during design and development. Commissioning required a major effort on calibration and fine setting and led to development of new functionalities. The RFPS was validated under full power and 125-mA deuteron beam loading conditions, in the radio frequency quadrupole (RFQ), demonstrating good performance. This article is an overview about how technical challenges impacted the prototype RFPS design and its functional evolution during commissioning, cavity conditioning, and beam operation of the RFQ.

The IFMIF accelerator facility consists of 2 identical linacs, each accelerating a 125 mA CW deuteron beam up to the energy of 40 MeV. In order to reach these unprecedented performances, the Linear IFMIF Prototype Accelerator (LIPAc) is under installation and commissioning at the International Fusion Energy Research Centre (IFERC) in Rokkasho, Japan, in the framework of the IFMIF/EVEDA project, which is part of the Broader Approach (BA) agreement between Japan and EU. The accelerator is designed to validate components up to 125 mA CW deuteron beam at 9 MeV. The accelerator components of LIPAc have been designed and manufactured mainly by European Institutes. The injector and superconducting linac, RFQ, MEBT, Diagnostics Plate, HEBT and beam dump have been developed respectively by CEA-Saclay, INFN-Legnaro and CIEMAT-Madrid and were delivered to Rokkasho between 2013 and 2016. The commissioning of the injector with beam started in November 2014. This paper dealt with the experimental data obtained with the beam diagnostics of the injector. The electrical measurements of the beam intensity on the beam stopper were compared with calorimetric measurements. The beam profiles measured with a CCD camera and a custom image-intensified CID camera are also addressed. The analysis of beam emittance and ion species fractions from data obtained with an Allison scanner is described and the results of species fraction measurements are compared with those obtained by using a deported spectrometer. Finally, the analysis of beam space potential from data obtained with a 4-Grid analyser is presented.

The construction of the Linear IFMIF Prototype Accelerator (LIPAc) is in progress in order to demonstrate the feasibility of the low energy section of an IFMIF deuteron accelerator up to 9 MeV with a beam current of 125 mA in CW. The next milestone of the project is the so-called Phase-B beam commissioning, and one of the missions is to demonstrate the acceleration of the proton beam up to 2.5 MeV or the deuteron beam up to 5.0 MeV in pulsed mode with a low duty cycle of 0.1% through RFQ. Most of the components and subsystems necessary for Phase-B were delivered by 2016 under the responsibility of Fusion for Energy (F4E) as in-kind contributions of several European institutes, namely CEA (France), CIEMAT (Spain), INFN (Italy), and SCK-CEN (Belgium), and QST is in charge of the installation of the delivered equipment. The installation and check-out of the RFQ subsystem and the RF power system was completed by July 2017, and the RF conditioning of the RFQ cavity started. Also, the installation and the check-out of the important sub-systems for Phase-B, namely MEBT and beam diagnostics, have been completed. Keywords: IFMIF, LIPAc, RFQ, Accelerator, Deuteron, Neutron source

The Radio Frequency Quadrupole (RFQ) linac and 1.6 MW RF power system of the Linear IFMIF Prototype Accelerator (LIPAc) facility in the International Fusion Energy Research Center (IFERC) in Rokkasho (Japan) has been installed and conditioned. During the assembly and tuning process, the RFQ cavity was protected with a temporary tent from the potential deterioration of performance caused by dust. The vacuum in the cavity was improved through the 100 °C baking process of the cavity. The high power test of the 175 MHz RF systems up to 200 kW in CW for each of the eight RF chains was performed for checking its stable output reproducibility in Japan, before connecting 9–3/16 inch coaxial transmission lines from the RF chains to the RF input couplers of the cavity. It was confirmed that the eight RF chains provided the balanced RF power to the single RFQ cavity in-phase using a feedback loop and a synchronization system. The peak power in the cavity achieved 150 kW in the pulsed mode, which corresponds approximately to the required electric field to accelerate proton beam. Such RF conditioning process is ongoing to achieve 600 kW approximately required for deuteron beam commissioning planned in 2018.

For the development of the International Fusion Materials Irradiation Facility (IFMIF) aiming at material tests for fusion power plants, the construction of the Linear IFMIF Prototype Accelerator (LIPAc) has been conducted at Rokkasho, Japan under the Broader Approach Agreement. The commissioning of LIPAc has been progressing significantly. The world most powerful RFQ successfully accelerated proton beam of 58 mA, and an important project milestone of the acceleration of deuteron beam to 5 MeV with the beam current of 125 mA in pulse mode was successfully achieved. The result proves the validity of the present RFQ design. The adjustment and tuning of the RF power system and the injector for enabling an operation at maximum performances played an important role in achieving this result. For the next step, the preparation of the high duty cycle operation of RFQ is underway. The installation of the HEBT (High Energy Beam Transport line) and the beam dump accepting 1 MW, CW beam, has been completed and a new beam transport line is under manufacturing. Also the assembly of the Superconducting RF (SRF) linac to accelerate the beam up to 9 MeV started in a clean room in Rokkasho.

The goal of LIPAc (Linear IFMIF Prototype Accelerator) is to achieve a 125 mA, 9 MeV, CW (continuous wave, i.e. 100% duty cycle) deuteron beam with an average beam power of 1.125 MW. In the beam current measurement, it is considered that calorimetric measurement is advantageous for high current and CW operations since it is not subject to secondary electrons, etc. In calorimetric measurements, it is necessary to measure the temperature rise of the cooling water as accurately as possible. We applied this method to LIPAc proton beams at the Beam Stop unit. In order to check the reliability, we inserted a heater in the cooling loop as a heat source and obtained correlation between the applied and measured power, which was found to be 1.0. Moreover, using this heater, accuracy of this measurement with respect to the flow rate of the cooling water was investigated. Due to heat transfer and the fluctuations of water temperature, etc., there is a range of flow rates in which the measurement error can be minimized with our calorimetric measurement system.

During the EVEDA (engineering validation and engineering design activities) phase of the International Fusion Materials Irradiation Facility (IFMIF) project, a 125 mA/9 MeV linear prototype accelerator (LIPAc) has to be built, tested and operated in Rokkasho-mura (Japan). Involved in this project for several years, CEA-Saclay designed the injector of this accelerator which is composed of an electron cyclotron resonance ion source, delivering a 140 mA deuteron beam at 100 keV, and a low energy beam transport (LEBT) line to match the beam for the injection into the radio-frequency quadrupole. In this paper, the components of the LIPAc injector are described. The commissioning of the ion source and LEBT with beam started in November 2014. The different phases of the commissioning are explained and some noticeable experimental results obtained with a beam at 100 keV are presented.