Search

The mutual inductance model enables testing of the behavior of power transformers under different operation conditions, especially under the environmental influences on the transformer's core. This paper presents the results of an investigation of the stress dependence of the magnetic relative permeability of a power transformer. It was observed that under tensile mechanical stresses up to 98 MPa applied to the core, the transformer input current amplitude increases by almost 67%, whereas the transformer's reactive power increases by 53%. In industrial systems, such changes can potentially lead to unwanted power system shutdowns due to overloading. This effect should be considered during the development of critical power systems. [ABSTRACT FROM AUTHOR]

Silicone rubber (SIR) is a crucial insulating material in cable accessories, but it is also susceptible to faults. In practical applications, mechanical pressure from bending or shrinking can impact the degradation of SIR, necessitating the study of its electrical tree and partial discharge (PD) characteristics under such pressure. This work presents the construction of a test platform for electrical trees under varying pressures to observe their growth process. A high-frequency current transformer is used to measure PD patterns during tree growth, enabling analysis of the effect of PD on tree initiation and propagation under pressure. The experimental results demonstrate a significant decrease in tree inception probability and increase in PD inception voltage under pressure. The pressure also influences the tree structure and PD during the treeing process, where the longest tree with a branch-like structure appears under 800 kPa. The effect of pressure on electrical tree and PD characteristics can be attributed to changes in free volume, alterations in air pressure within the tree channels, and the affected charge accumulation. [ABSTRACT FROM AUTHOR]

A polarity identification is very important for operation of transformers, measurement and protection equipment, where it is useful in analyzing of transformer connections and operation as well as testing of protective systems. Moreover, it's essential in assessment of power systems performance during both normal and abnormal operation. Ensuring the correct polarity of the primary and secondary windings in voltage and current transformers is of paramount importance for various measurement and protection schemes in power networks. This paper proposes a digital polarity detector and tester using correlation coefficients and nine polarity indices calculated for instrument transformer signals. In order to test the performance of the proposed polarity tester algorithm, MATLAB code is imported to the LABVIEW model, and the numerical data obtained from the synchronous generator terminals via instrument transformers are interfaced with the computer through the Data Acquisition Card (DAC). The experimental system consists of a motor-generator set supplying a three-phase inductive load with instrument transformers connected to measure each phase voltage and current. The obtained results for various operating conditions and different types of abnormal conditions prove that the suggested algorithm is accurate, reliable and applicable to smart grids and substation automation systems. It can be considered as an integrated system incorporated with digital fault recorders, relays and meters. [ABSTRACT FROM AUTHOR]

With the emergence of the new generation vision architecture Vmamba and the further demand for agricultural yield and efficiency, we propose an efficient and high-accuracy target detection network for automated pear picking tasks based on Vmamba, aiming to address the issue of low efficiency in current Transformer architectures. The proposed network, named SRSMamba, employs a Reward and Punishment Mechanism (RPM) to focus on important information while minimizing redundancy interference. It utilizes 3D Selective Scan (SS3D) to extend scanning dimensions and integrates global information across channel dimensions, thereby enhancing the model's robustness in complex agricultural environments and effectively adapting to the extraction of complex features in pear orchards and farmlands. Additionally, a Stacked Feature Pyramid Network (SFPN) is introduced to enhance semantic information during the feature fusion stage, particularly improving the detection capability for small targets. Experimental results show that SRSMamba has a low parameter count of 21.1 M, GFLOPs of 50.4, mAP of 72.0%, mAP50 reaching 94.8%, mAP75 at 68.1%, and FPS at 26.9. Compared with other state-of-the-art (SOTA) object detection methods, it achieves a good trade-off between model efficiency and detection accuracy. [ABSTRACT FROM AUTHOR]

The Pulsed Energetic Electrons for Research (PEER) beamline at the ANSTO Australian Synchrotron comprises a 100 MeV linac injector that is currently being developed for ultra-high dose-rate, very high-energy electron radiotherapy research. Previously, dosimetry studies discovered a lack of reliable charge measurement to the in-air end station, though no change in response was recorded in fast current transformer measurements, the only available diagnostic device for measuring charge. This work describes the process of simulating and then commissioning a purpose-built Faraday cup to ascertain absolute in-air charge measurements at PEER. By combining simulation data with experimental results, the PEER Faraday cup is shown to possess a primary electron capture efficiency of (99.22 ± 0.10)%, with a net capture efficiency due to secondary electron emission of (97.87 ± 0.24)%. These results show the PEER Faraday cup performs as intended and, when scaled against simulations, will be suitable for measuring absolute charge at PEER. [ABSTRACT FROM AUTHOR]

The publication addresses the dynamic state challenges encountered during development of a dual active bridge (DAB) converter within DC microgrid systems. The conventional startup method is identified as instigating a cascade of unfavorable outcomes, encompassing elevated starting current, transformer current asymmetry, DC voltage distortions, EMI and heightened thermal stress on semiconductor components. Additionally, it necessitates precise calibration of magnetic components and diodes. A proposed remedy to these issues is introduced, involving a control method based on an additional phase shift to modulate the current of the primary H bridge. This novel control methodology is posited as a means to mitigate the aforementioned undesirable effects associated with traditional converter initiation techniques. The research also delves into considerations of a proper design procedure for the converter. Emphasis is placed on integrating the novel control methodology into the design framework in order to effectively address challenges arising during transient states. Validation of the proposed solution is substantiated through a series of laboratory tests, the results of which are comprehensively presented in the article. These tests affirm the efficiency of the system when incorporating the novel control methodology, thereby substantiating its practical utility in mitigating the issues identified during the initiation phase of the DAB converter in DC microgrid systems. [ABSTRACT FROM AUTHOR]

When two-or-more-point grounding faults occur in the secondary circuit of a substation, they will lead to large data measurement errors in the protection, measurement, and control devices, which can easily cause protection malfunction. At present, there is a lack of an online panoramic monitoring system for the secondary circuits of substations, and it is difficult to accurately identify the faults in these secondary circuits. In order to solve this problem, this paper proposes a cloud–edge collaboration framework for the power Internet of Things (IoT), which can accurately identify faults by monitoring the secondary circuit of power grid substations with panoramic online status, reducing maintenance costs and improving overall operational efficiency. Firstly, the collection requirements of current transformer (CT) and potential transformer (PT) fault characteristics in the secondary circuit of the substation are analyzed. The platform architecture of the secondary loop panoramic monitoring system of the cloud-side cooperative substation is proposed, along with the algorithm and data wireless acquisition scheme of the edge computing, cloud computing, and cloud-side system. Furthermore, the edge computing platform and the current and voltage wireless sensors are developed. The maximum error in the accuracy test of the voltage sensor is 1.9180%, while the maximum error in the accuracy test of the current sensor is 1.3406%. [ABSTRACT FROM AUTHOR]

Energy harvesting technology, as an emerging energy technology, has contributed outstandingly to the application of online monitoring sensors in power systems. The accurate parameter identification of the harvesters is crucial for their power supply applications. This work aims to investigate the parameter identification of harvesters with complex equivalent circuit models, here taking a current transformer as an example. However, previous studies focused on optimizing algorithms rather than data sources. This paper demonstrates a vector impedance quantum genetic algorithm (QGA) parameter identification method to identify the amplitude and phase information of the impedance responses. By comparing the results of the proposed method with the genetic algorithm and PSO based on impedance responses and QGA based on load resistance responses, it is proved that the proposed vector impedance QGA identification method is optimal in terms of accuracy, speed, and robustness. The root mean square errors of the output voltage and the phase difference with the primary current for the proposed method are 5.884 × 10−5 V and 4.473 × 10−4 ms. Moreover, the practical applicability of this method is validated, demonstrating its effectiveness in real‐life and industrial settings. The proposed identification method in this paper changes the source data so that the sample data are small in volume and extensive in information, which enables faster and more accurate parameter identification. This study provides a new idea for parameter identification researches. [ABSTRACT FROM AUTHOR]

Background and purpose Methods Results Conclusion FLASH or ultra‐high dose rate (UHDR) radiation therapy (RT) has gained attention in recent years for its ability to spare normal tissues relative to conventional dose rate (CDR) RT in various preclinical trials. However, clinical implementation of this promising treatment option has been limited because of the lack of availability of accelerators capable of delivering UHDR RT. Commercial options are finally reaching the market that produce electron beams with average dose rates of up to 1000 Gy/s. We established a framework for the acceptance, commissioning, and periodic quality assurance (QA) of electron FLASH units and present an example of commissioning.A protocol for acceptance, commissioning, and QA of UHDR linear accelerators was established by combining and adapting standards and professional recommendations for standard linear accelerators based on the experience with UHDR at four clinical centers that use different UHDR devices. Non‐standard dosimetric beam parameters considered included pulse width, pulse repetition frequency, dose per pulse, and instantaneous dose rate, together with recommendations on how to acquire these measurements.The 6‐ and 9‐MeV beams of an UHDR electron device were commissioned by using this developed protocol. Measurements were acquired with a combination of ion chambers, beam current transformers (BCTs), and dose‐rate–independent passive dosimeters. The unit was calibrated according to the concept of redundant dosimetry using a reference setup.This study provides detailed recommendations for the acceptance testing, commissioning, and routine QA of low‐energy electron UHDR linear accelerators. The proposed framework is not limited to any specific unit, making it applicable to all existing eFLASH units in the market. Through practical insights and theoretical discourse, this document establishes a benchmark for the commissioning of UHDR devices for clinical use. [ABSTRACT FROM AUTHOR]

In modern power systems, there is a growing need for protection techniques that are fast, precise, and stable to enhance the reliability and stability of power networks. This paper introduces an advanced technique for fault direction estimation that addresses key limitations in existing methods. Our proposed algorithm eliminates the dead‐zone issue, effectively handling both forward and reverse faults regardless of their location, including faults near relay regions. Using genetic programing (GP), we derive a closed‐form equation to drive the fault direction estimation algorithm, ensuring accurate and reliable results. The algorithm demonstrates exceptional speed and reliability in fault detection and direction estimation, even under challenging conditions such as current transformer (CT) saturation, power swing, and source strength variations. It is also insensitive to fault resistance and fault inception angle, increasing its robustness. A notable advantage of this algorithm is its efficiency at low sampling frequencies, making it highly adaptable for industrial applications and compatible with modern software and hardware requirements. We validated the algorithm through simulations on the electromagnetic transients program (EMTP‐RV) platform and with field data from the Manesht 230 kV substation in Ilam province, Iran. The results confirm the algorithm's impressive speed and high reliability. [ABSTRACT FROM AUTHOR]

In power transformers, lightning strikes, switching operations, and short circuit faults can deform the winding insulation, resulting in an electric arc between the windings. If the arc is not detected in its initial phase, it may lead to a solid short circuit and damage the transformer, potentially causing an explosion due to overheating and high pressure. In this study, winding arcs in the transformer are identified from the terminal current and voltage signals. A 3D magnetic model of a 15 MVA power transformer is constructed in Ansys@Maxwell, and the nonlinear arc model is simulated in Matlab@Simulink. The transient voltage and current signals related to the arcing conditions at five different points in the high-voltage side winding are obtained by running Ansys and Matlab simultaneously using ANSYS@Simplorer (Twin Builder). These signals are transformed into the frequency domain using Fast Fourier Transform (FFT). The arcs are detected from the transient-generated frequency components of the transformer voltage and current signals. [ABSTRACT FROM AUTHOR]

In this work, a new methodology is proposed for the online and non-invasive extraction of partial discharge (PD) pulses from raw measurement data obtained using a simplified setup. This method enables the creation of sub-windows with optimized size, each containing a single candidate PD pulse. The proposed approach integrates mathematical morphological filtering (MMF) with kurtosis, a first-order Savitzky-Golay smoothing filter, the Otsu method for thresholding, and a specific technique to associate each sub-window with the phase angle of the applied voltage waveform, enabling the construction of phase-resolved PD (PRPD) patterns. The methodology was validated against a commercial PD detection device adhering to the IEC (International Electrotechnical Commission) standard. Experimental results demonstrated that the proposed method, utilizing an off-the-shelf 8-bit resolution data acquisition system and a low-cost high-frequency current transformer (HFCT) sensor, effectively diagnoses and characterizes PD activity in high-voltage equipment, such as surge arresters and instrument transformers, even in noisy environments. It was able to characterize PD activity using only a few cycles of the applied voltage waveform and identify low amplitude PD pulses with low signal-to-noise ratio signals. Other contribution of this work is the diagnosis and fault signature obtained from a real surge arrester (SA) with a nominal voltage of 192 kV, corroborated by destructive disassembly and internal inspection of the tested equipment. This work provides a cost-effective and accurate tool for real-time PD monitoring, which can be embedded in hardware for continuous evaluation of electrical equipment integrity. [ABSTRACT FROM AUTHOR]

When a transformer is in a long-term heavy load operation state, the oil temperature reaches the alarm temperature; if a slight fault occurs inside the transformer, traditional inverse time current protection and other protections that react to phase current may not operate due to insufficient sensitivity or they may operate for too long. Based on this, this article proposes a new principle of accelerating inverse time overcurrent protection based on transformer oil temperature. The proposed method uses transformer oil temperature to accelerate the action time of traditional inverse-time overcurrent protection, then introduces the transformer oil temperature factor and acceleration index to optimize the inverse time characteristic curve, and establishes a mathematical model to optimize the adjustment for the complexity of adjustment of the protection action equation and the risk of mismatch of the protection after the acceleration of oil temperature. The existing theoretical analysis and simulation verification results show that the proposed new overcurrent protection scheme based on the transformer oil temperature acceleration inverse time can effectively improve the protection of the rapidity and sensitivity, providing a new research idea for the combination of non-electrical and electrical quantity protection. [ABSTRACT FROM AUTHOR]

In technology and industrial production, many applications require wide-bandwidth current measurements. In this paper, a signal fusion scheme for a current sensor comprising tunneling magnetoresistance and a current transformer is proposed, achieving a flat frequency response in the DC to MHz range. The measurement principles in different cases of the scheme are introduced, and the total transfer function of the entire scheme is derived by analyzing each section separately. Furthermore, the feasibility and selected parameters of the scheme are verified through a systematic simulation utilizing the MATLAB software. Based on the proposed scheme, a group of principal prototypes are built to experimentally evaluate the bandwidth, amplitude and phase flatness, accuracy, sensitivity, and impulse response. The relative amplitude variation in the passband of the fusion sensor is less than 4%, and the estimated bandwidth of the fusion sensor is close to 17 MHz. The accuracy is better than 0.6%, even when measuring the current at 1 MHz, and the relative standard deviation is 5% when measuring the impulse signal. The sensors developed using this scheme, with a low financial cost, have advantages in many wide-bandwidth current measuring scenarios. [ABSTRACT FROM AUTHOR]

To maintain the security of transformer differential protection, it is essential to restrain its response to oversetting differential current caused by the inrush current or other switching conditions. This paper presents a new proposed method to discriminate the transformer's internal fault from the inrush current; the discrimination process is based on a convolutional neural network (CNN) with a combination of the higher order spectral estimations that perform a deep learning classification with high accuracy. This research succeeded in proposing two robust and efficient CNN models; the first one is the 1D CNN, which takes the sole signal without any transformation, while the second model is the 2D CNN, which takes the short‐time Fourier transform of the signal. Both developed models are light and have the minimum number of layers that can achieve a very high performance. The performance of the proposed models is tested using a dataset prepared according to laboratory‐measured transformer parameters. The results are compared with other well‐known methods, and the achievement of high numerical performance evaluation validates the consistency of the proposed methods. [ABSTRACT FROM AUTHOR]

The article discusses the impact of reactive power load on additional power losses in a high-power transformer operating at a VAr static compensation station. The presence of an almost pure capacitive load on the secondary side together with the thyristor switches is the cause of high-frequency components in the phase currents. The additional effect of electrical resonance between the transformer inductance and the load capacitance is also taken into account. The analysis is achieved using a three-dimensional finite element approach. [ABSTRACT FROM AUTHOR]

Mechanical stability is one of the core capabilities of power transformers. External short‐circuit accidents are the main cause of winding instability. International Electrotechnical Commission 60076‐5 standard recommends a method to calculate the short‐circuit strength of power transformer windings by comparing the stress within windings under the effect of the maximum electromagnetic force with the critical stress of the winding. This method assumes that the maximum deformation will be produced by the maximum electromagnetic force, which corresponds to the first peak of the waveform. However, owing to the interactions between disks during the vibration process, the maximum deformation may occur after the occurrence of the maximum electromagnetic force. The hysteresis phenomenon between disk deformation and electromagnetic force is studied. The definition of the hysteresis phenomenon during the vibration process is first demonstrated, and the mechanism of the hysteresis phenomenon is investigated. The vibration model is established. By decoupling analysis, the conditions for the formation of hysteresis are proposed, and the mechanism of the hysteresis phenomenon is validated by the experiment, which is conducted on a winding sample. In the deformation formula, the term that determines the time‐varying characteristic is found. The waveform‐determining term is the difference between the two cosine components, whose frequencies are the natural vibration frequency and the electromagnetic force frequency. When the two frequencies are close, the maximum deformation lags behind the maximum force, and the hysteresis phenomenon occurs. [ABSTRACT FROM AUTHOR]

The transformer grounding is typically inserted across a transformer or generator's ground. In a transformer and generator, this ground is often used to reduce the current of a disturbance from phase to earth. During a ground fault in a transformer, a very high current can flow, posing a danger to equipment and personnel. By connecting a resistor between the neutral point of the transformer and ground, the NGR limits this fault current. In the following paper, the protection mechanism of two high-voltage to medium-voltage transformers which connected in parallel during routine operation as well as in emergency situations will be explored. Protecting two parallel transformers with two different neutral grounding resistors involves ensuring proper coordination of protective devices to detect and isolate faults while minimizing damage to equipment and ensuring system stability. Another scenario under discussion involves a generator linked to the medium-voltage (MV) system, which distinct had a distinct ground value. A short circuit occurring in different neutral grounding resistor (NGR) systems refers to a fault scenario where more than one transformer or generator linked in parallelly, each with its own NGR of varying resistance values. This situation poses challenges for protection coordination and fault current distribution. To address this issue, a protective scheme is suggested, which modifies its configurations according to the operational status of the system. [ABSTRACT FROM AUTHOR]

Power transformers are vital and costly components in power systems, essential for ensuring a reliable and uninterrupted supply of electrical energy. Their protection is crucial for improving reliability, maintaining network stability, and minimizing operational costs. Previous studies have introduced differential protection schemes with harmonic restraint to detect internal transformer faults. However, these schemes often struggle with computational inaccuracies in fault detection due to neglecting current transformer (CT) saturation and associated uncertainties. CT saturation during internal faults can produce even harmonics, disrupting relay operations. Additionally, CT saturation during transformer energization can introduce a DC component, leading to incorrect relay activation. This paper introduces a novel feature extracted through advanced wavelet transform analysis of differential current. This feature, combined with differential current amplitude and bias current, is used to train a deep learning system based on long short-term memory (LSTM) networks. By accounting for existing uncertainties, this system accurately identifies internal transformer faults under various CT saturation and measurement uncertainty conditions. Test and validation results demonstrate the proposed method's effectiveness and superiority in detecting internal faults in power transformers, even in the presence of CT saturation, outperforming other recent modern techniques. [ABSTRACT FROM AUTHOR]

To solve the problem of the large size of traditional industrial frequency phase-shift transformers and the harmonic distortion of multi-pulse wave rectifier systems, this paper proposes a three-stage shunt zigzag power electronic phase-shift transformer based on a double-tap multi-pulse wave rectifier, which combines the power factor correction (PFC) converter with the voltage-type SPWM inverter circuit to form a power electronic converter to realize the frequency boost and power factor correction. Through AC–DC–AC conversion, the frequency of the three-phase AC input voltage is increased, the number of core and coil turns in the transformer is reduced to reduce the size of the phase-shifter transformer, a zigzag structure of the phase-shifter transformer is used to solve the unbalanced distribution of current between the diode bridges, and a passive harmonic suppression method on the DC side is used to generate a loop current by using a group of single-phase rectifier bridges to regulate the input line current of the phase-shifter transformer. The phase-shifted voltage is input into two three-phase diode rectifier bridges to rectify and supply power to the load. Simulation and semi-physical test results show that the proposed method reduces the total harmonic distortion (THD) value of the input current of the phase-shifted transformer to 7.17%, and the THD value of the grid-side input current is further reduced to 2.49%, which meets the harmonic standard and realizes the purpose of power factor correction as well as being more suitable for high-power applications. [ABSTRACT FROM AUTHOR]

Non-toroidal-shaped primary pass-through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow the passing of several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables passed through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, then the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed, causing the malfunction of the CT. In this paper, the performance of a non-toroidal-shaped protection CT is studied. This research is focused on the influence of the cable position on possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from the assigned ratio. The validation of this phenomenon was carried out via finite element analysis (FEA), showing that partial transformer core saturations appear in areas of the magnetic core close to the cable. By applying FEA, the admissible accuracy region for cable positioning inside the CT is also delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs, varying the primary cables' positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given. [ABSTRACT FROM AUTHOR]

The power transformers are the important part of electrical networks where transformer reliability and operational lifetime depends on sufficiently accurate and reliable protective means. Other traditional forms of differential protection that were developed initially also suffer from the inability to distinguish between a fault and normal operation such as inrush currents in transformers and CT saturation. This paper presents the development of an improved differential relay augmented by Fuzzy-Logic Control System (FLC), to improve (a) dependability, (b) performance of the existing transformer protection systems, and (c) accuracy in fault identification possible due to uncertainty and non-linearity in transformer operation. They include the proposed methodology compared to the traditional Rule-based current differential method in outlining the protection settings. MATLAB/Simulink model of the power transformer and protection methods suggested in the study form a part of the investigation. Computer simulations show that the presented scheme provides a substantial increase in the speed and resolution of fault detection and fault types identification relating to current differential method based on the Rule. The system's accuracy rate is the average of 98% for internal faults and 95% for external faults while its response time is 25ms for internal faults and 30ms for external faults. Furthermore, the Fuzzy-Logicbased system has an 90% efficiency in detect the defect and 85% efficiency in identify the inrush currents. The findings of this research prove that the differential relay based on Fuzzy-Logic enhances the flexibility and reliability of transformer protection and opens the road to the introduction of further improvements in the intelligent protection systems in the future. [ABSTRACT FROM AUTHOR]

Today's prediction of ocean dynamics relies on numerical models. However, numerical models are often unable to accurately model and predict real ocean dynamics, leading to a lack of fulfillment of a range of services that require reliable predictions at various temporal and spatial scales. Indeed, a numerical model cannot fully resolve all the physical processes in the ocean due to various reasons, including biases in the initial field and calculation errors in the numerical solution of the model. Thus, bias-correcting methods have become crucial to improve the dynamical accuracy of numerical model predictions. In this study, we present a machine learning-based three-dimensional velocity bias correction method derived from historical observations that applies to both hindcast and forecast. Our approach is based on the modification of an existing deep learning model, called U-Net, designed specifically for image segmentation analysis in the biomedical field. U-Net was modified to create a Transform Model that retains the temporal and spatial evolution of the differences between the model and observations to produce a correction in the form of regression weights that evolves spatially and temporally with the model both forward and backward in time, beyond the observation period. Using daily ocean current observations from a 2.5-year current meter array deployment, we show that significant bias corrections can be conducted up to 50 days pre- or post-observations. Using a 3-year-long virtual array, valid bias corrections can be conducted for up to one year. [ABSTRACT FROM AUTHOR]

Fiber optical current transformer (FOCT) is widely used in power systems for fault diagnosis and analysis, which can improve its operational reliability. Construct fault modes and fault trees based on fault data of all fiber current transformers, and construct a fault feature space. Constructing a fault diagnosis expert system using fault trees and fault feature space clustering centers to achieve accurate diagnosis of fault types, patterns, and components. The proposed method was validated using fault data and case studies of all fiber current transformers in a regional power grid, and the results showed that: The on-site fault case is closest to the cluster center of drift deviation fault, so it belongs to drift deviation fault. Further extract the on-site maintenance report, which indicates that the operating temperature of the all fiber current transformer is relatively high. The diagnostic results of the fault diagnosis expert system for the faulty all fiber current transformer are consistent with the actual results on site, verifying the accuracy and reliability of this method. [ABSTRACT FROM AUTHOR]

Copyright of Zhejiang Electric Power is the property of Zhejiang Electric Power Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

To meet the growing demand for integrated monitoring of complex power grid equipment, it is necessary to improve the situational awareness model of power transformers. The model is expected to assist monitoring personnel in timely identifying transformers with deteriorating trends among massive and discrete monitoring information, and to make responses in advance. However, the current transformer state awareness technology generally has the problem of single data source and poor timeliness, and still requires monitoring personnel to make artificial analysis and prediction in combination with telemetry information, which cannot fully meet the requirements of power grid equipment monitoring. This paper is based on multi-source data fusion technology, through associating and mining transformer alarm information, equipment maintenance records and power transmission and transformation online monitoring data, to extract the dimension features of transformer operation situation assessment. By constructing a multi-layer perceptron model, a transformer state transition model based on the principle of Markov chain is established, which can predict possible defects 2 h in advance and achieve good results, and determine the transformer state early warning index, providing sufficient time for monitoring personnel to deploy transformer operation and maintenance work in advance. Finally, the effectiveness of the method proposed in this paper is proved by the case of transformer crisis state in a city substation, and the method proposed in this paper has important significance for transformer state early warning. [ABSTRACT FROM AUTHOR]

Construction of relay protections of electrical installations without the use of bulky metal- and insulation-intensive measuring current transformers (CTs) was repeatedly discussed at Conferences of the International Council on Large Electric Systems (CIGRE) as a challenge for the electric power industry. In the article, the authors present resource-saving reed switch current protection for 6–10-kV electrical installations connected to switchgear cells, which is an alternative to traditional protections. The scientific novelty of the work lies in (a) reed switch protection design on the basis of measuring the magnetic induction in different modes and at different points inside a cell, and we prove that inductance values are sufficient to detect phase short-circuits in electrical installations fed from this cell and derive the dependence of the induction on the position of an inductance coil inside the cell; (b) proven possibility of using the simplest formula of the Biot–Savart law for the calculations if the experimentally obtained coefficients are introduced into it; (c) development of a technique for calculating the parameters of the overcurrent protection based on reed switches. Experimental results are presented in graphical form and clearly show the points of EMS maxima and minima. Settings for resource-saving current protection are selected and a feasibility study of the effectiveness of resource-saving overcurrent protection is carried out. A technical and economical assessment of the efficiency of the suggested overcurrent protection is conducted. [ABSTRACT FROM AUTHOR]

In general, a high voltage (HV) substation can be made up of multiple insulation subsystems: an air insulation subsystem (AIS), gas insulation subsystem (GIS), liquid insulation subsystem (power transformers), and solid insulation subsystem (power cables), all of them with their grounding structures interconnected and linked to the substation earth. Partial discharge (PD) pulses, which are generated in a HV apparatus belonging to a subsystem, travel through the grounding structures of the others. PD analyzers using high-frequency current transformer (HFCT) sensors, which are installed at the connections between the grounding structures, are sensitive to these traveling pulses. In a substation made up of an AIS, several non-critical PD sources can be detected, such as possible corona, air surface, or floating discharges. To perform the correct diagnosis, non-critical PD sources must be separated from critical PD sources related to insulation defects, such as a cavity in a solid dielectric material, mobile particles in SF6, or surface discharges in oil. Powerful diagnostic tools using PD clustering and phase-resolved PD (PRPD) pattern recognition have been developed to check the insulation condition of HV substations. However, a common issue is how to determine the subsystem in which a critical PD source is located when there are several PD sources, and a critical one is near the boundary between two HV subsystems, e.g., a cavity defect located between a cable end and a GIS. The traveling direction of the detected PD is valuable information to determine the subsystem in which the insulation defect is located. However, incorrect diagnostics are usually due to the constraints of PD measuring systems and inadequate PD diagnostic procedures. This paper presents a diagnostic procedure using an appropriate PD analyzer with multiple HFCT sensors to carry out efficient insulation condition diagnoses. This PD procedure has been developed on the basis of laboratory tests, transient signal modeling, and validation tests. The validation tests were carried out in a special test bench developed for the characterization of PD analyzers. To demonstrate the effectiveness of the procedure, a real case is also presented, where satisfactory results are shown. [ABSTRACT FROM AUTHOR]

Micro-Computed Tomography (µCT) systems are used for examining the internal structures of various objects, such as material samples, manufactured parts, and natural objects. Resolving fine details or performing accurate geometric measurements in the voxel data critically depends on the precise calibration of the µCT systems geometry. This paper presents a calibration method for µCT systems using projections of a calibration phantom, where the coordinates of the phantom are initially unknown. The approach involves detecting and tracking steel ball bearings and adjusting the unknown system geometry parameters using non-linear least squares optimization. Multiple geometric models are tested to verify their suitability for a self-calibration approach. The implementation is tested using a calibration phantom captured at different magnifications. The results demonstrate the system's capability to determine the geometry model parameters with a remaining error on the detector between 0.27 px and 0.18 px. Systematic errors that remain after calibration, as well as changing parameters due to system instabilities, are investigated. The source code of this work is published to enable further research. [ABSTRACT FROM AUTHOR]

This work proposes a methodology for noise removal, separation, and classification of partial discharges in electrical system assets. Partial discharge analysis is an essential method for fault detection and evaluation of the operational conditions of high-voltage equipment. However, it faces several limitations in field measurements due to interference from radio signals, television transmissions, WiFi, corona signals, and multiple sources of partial discharges. To address these challenges, we propose the development of a clustering model to identify partial discharge sources and a classification model to identify the types of discharges. New features extracted from pulses are introduced to model the clustering and classification of discharge sources. The methodology is tested in the laboratory with controlled partial discharge sources, and field tests are conducted in substations to assess its practical applicability. The results of laboratory tests achieved an accuracy of 85% in classifying discharge sources. Field tests were performed in a substation of the Eletrobras group, allowing the identification of at least three potentially defective current transformers. [ABSTRACT FROM AUTHOR]

Copyright of Zhejiang Electric Power is the property of Zhejiang Electric Power Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Zhejiang Electric Power is the property of Zhejiang Electric Power Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Current transformers (CTs) are widely used for energy metering, relay protection, condition monitoring and control circuits. However, CT saturation may lead to non‐negligible measurement errors and relay malfunctions, posing a threat to the stability and security of the power grid. In order to address the problem of CT saturation, a novel measurement‐protection‐integrated current transformer (MPICT) is proposed. First, the working states of the MPICT are summarised and the approximate expressions for the steady‐state measuring characteristics, the transient response characteristics, and the measurement errors are derived from the equivalent circuit model. Then, the feasibility of the MPICT and the theoretical analyses are verified by the 3D FEM simulation imitating the presented MPICT excited by diverse currents. Finally, a down‐scale prototype is fabricated and a series of tests are conducted in the laboratory to validate the effectiveness of the equipment. The simulation and experimental results suggest that the output of the MPICT can accurately reconstruct the primary current waveform, even if the primary current contains decaying or constant DC component. [ABSTRACT FROM AUTHOR]

In a wide range of current changes, it is difficult for current transformer to carry out steady energy extraction, because the excitation characteristics of current transformer are interfered by load impedance. To solve this problem, a dynamic impedance control strategy of voltage source converter is proposed. The method dynamically and continuously adjusts the secondary impedance according to the different states of the primary current, which not only meets the requirement of load power consumption under the condition of low current, but also reduces the influence of the magnetic saturation problem of the core. The principle of energy collection is analyzed, and the equivalent model of current transformer and circuit is established. The relationship between excitation characteristics and impedance parameters is discussed empirically-, which lays a foundation for the construction of the final control strategy. The experimental results show that, first, without capacitive impedance control, the effective value of ct induced voltage is 37.313V, and the corresponding energy collection power is 1.39W. Under the capacitive impedance control, the RMS value of ct induced voltage increases to 72.868V and the energy collection power reaches 5.31W. It can be seen that when the capacitive reactance state is changed, the RMS value of induced voltage and energy collection power are significantly different. Second, the output current of the strong current generator is adjusted to 70a, and when the current increases, the system enters the magnetic saturation state. At this time, the positive and negative half waves of the voltage and current on the CT secondary side produce high amplitude spike pulse waves, which is very dangerous to the insulation of the CT winding and the safety of the load equipment. Under the same conditions, after the induction impedance control is added to the CT core, the magnetic saturation state is relieved, and the waveform changes from peak wave to sine wave, the energy taking system returns to normal working state, the DC voltage output is normal, and the system power supply is stable. Third, the output current of the strong current generator continues to increase to 80a, with the increase of the primary current, the system waveform state remains stable, and the induced voltage and DC output voltage remain constant near the preset reference value. It can be concluded that the magnetic induction intensity of the core will be positively affected by the capacitive impedance operation, and the energy supply effect of the transformer will be increased. The operating characteristics of inductance impedance can reduce the magnetic induction intensity of the iron core, thus inhibiting the saturation of the iron core under high current operating conditions and maintaining stable power output. [ABSTRACT FROM AUTHOR]

Critical Thinking (CT) skills are highly valued by employers, leading to their integration into engineering education through various design- and problem-based approaches. Despite their recognized importance, the varying perceptions of CT present challenges in achieving a unified approach to its development and assessment. This paper reviews CT assessment in engineering education, particularly mapping Facione's CT skills with assessment approaches to discern how CT is evaluated. We conducted a systematic keyword search in the SCOPUS database and identified 462 articles from 2010 to March 2023. These were reviewed and distilled down to 80 articles included in this study. We find that CT has been recognized as an essential skill set, but there are no consistent definitions or means to assess it. Further, while CT is a multifaced skill, we find that very few assessment methods assess CT holistically. We identify three goals for CT assessment: (1) understand and recognize CT, (2) demonstrate CT, and (3) identify if CT has changed due to intervention. We discuss how different assessment approaches, including rubrics, surveys, standardized tests, and customized assessments, have been used and propose recommendations to support reaching a better understanding of CT assessment in engineering education. Further research is needed to understand better how these skills can be taught and assessed as part of engineering education to meet the needs of employers. [ABSTRACT FROM AUTHOR]

Residential consumption represents one of the most important percentages of total electricity consumption. A considerable number of household appliances consume energy even when they are not in operation, i.e., they are in the so-called standby state, thus producing additional costs, which become significant over time. In this context, one method to solve this problem is to develop a smart system capable of severing the power connection to devices in standby mode, thereby conserving energy and reducing the energy costs. The first step in the design of this system consists of the identification and accurate measurement of the standby state, which was carried out for three of the most common household appliances. Then, by using an ESP32 microcontroller, a system was designed to manage the operation of a relay module based on the current consumption of the connected equipment. Control over the system was achieved through a web application that works across all devices equipped with a web browser, offering functionalities to adjust current value time delays and to manually switch the system on or off. Finally, the deployment of this system across the three appliances studied led to a reduction in the energy consumption in standby mode of 26.68 kWh per month. [ABSTRACT FROM AUTHOR]

During their lifespan, high-voltage (HV) electrical systems are subjected to operating conditions in which electrical, mechanical, thermal and environmental-related stresses occur. These conditions over time lead to unforeseen failures caused by various types of defects. For this reason, there are several technologies for measuring and monitoring the electrical systems, with the aim of minimizing the number of faults. The early detection of defects, preferably in their incipient state, will enable the necessary corrective actions to be taken in order to avoid unforeseen failures. These failures generally lead to human risks and material damage, lack of power supply and significant economic losses. An efficient maintenance technique for the early detection of defects consists of the supervision of the dielectrics status in the installations by means of on-line partial discharge (PD) measurement. Nowadays, there are numerous systems in the market for the measurement of PD in HV installations. The most efficient with a reasonable cost will be those that offer greater security guarantees and the best positioned in the market. Currently, technology developers and users of PD measuring systems face difficulties related to the lack of reference procedures for their complete characterization and to the technical and economic drawback of performing the characterization tests on site or in laboratory installations. To deal with the previous difficulties, in this paper a novel method for the complete and standardized characterization of PD measuring systems is presented. The applicability of this method is mainly adapted for the characterization of systems operating in on-line applications using high-frequency current transformer (HFCT) sensors. For the appropriate application of the method, an associated and necessary scale modular test platform is used. In the test platform, the real on-site measuring conditions of an HV insulated distribution line are simulated in a controlled way. Practical characterizations, showing the convenience and advantages of applying the method using the modular test platform, are also presented. [ABSTRACT FROM AUTHOR]

With the deep penetration of renewable energy and power electronic equipment, the overcurrent protection of an intelligent miniature circuit breaker faces new challenges. The electronic controller of an intelligent miniature circuit breaker is typically powered by the bus current rather than the phase voltage to ensure a robust overcurrent protection response under all conditions, including severe short-circuit faults. So, the performance of the current transformer serving as an energy harvesting unit and the corresponding direct current to direct current convention circuit is one of the critical issues due to the limited volume of an intelligent miniature circuit breaker. In this research, a finite element model of a current transformer for an intelligent miniature circuit breaker is constructed by COMSOL to evaluate the impact of the core material, the core size, and the number of coil turns on the energy harvesting capability of the current transformer. Meanwhile, the relationship between the output of the power supply and its design parameters is investigated by circuit simulation. As a result, a novel type of current transformer is proposed based on well-designed parameters. Finally, experimental tests have been conducted to verify the hysteresis characteristics, output characteristics, and energy harvesting effect. The results demonstrate that the hysteresis properties of the transformer align with the simulation results. The power supply can work with a minimum current of 8 amperes, which is 23.08% better than before. [ABSTRACT FROM AUTHOR]

The object of research is a three-phase electricity metering unit, which includes a digital meter and measuring current transformers. The reduction of non-technological energy losses is restrained due to the insufficient accuracy of the accounting of electric energy in distribution power networks under a reduced load current of the metering unit. The possibility of representing the dependence of the relative error of electricity measurement on current values by a fuzzy function at reduced load has been confirmed. The boundaries of such a function are approximated with sufficient accuracy by the sum of two exponents, which is explained by its significant nonlinearity in the range of reduced current. The proposed EMRL software allows to estimate the real consumption and the most possible level of underaccounting based on the array of electricity meter readings. The accuracy of estimating by the EMRL the amount of electricity consumed with a probability of 0.7 can be estimated with a relative error not exceeding 2 %. The probability of psychophysical assessments of the accuracy of EMRL «very good» and «good» is at least 0.833. The trend of a significant decrease in the relative value of underaccounting with an increase in the level of electricity consumption was revealed. With a daily consumption of up to 10 kW·h, the amount of underaccounting can reach 18 %, and with a consumption of more than 20 kW·h, it does not exceed 6 %. The adequacy of the results of estimating the amount of consumed electricity at reduced load using the EMRL was confirmed by experimental data at a significance level of 0.05. The software capabilities allow to increase the accuracy of the accounting of electrical energy in distribution networks with a reduced load current of the metering unit. The program can be used as part of automated systems of commercial electricity metering or advanced metering infrastructure to determine the most possible underaccounting due to the operation of metering units at a reduced load [ABSTRACT FROM AUTHOR]

In recent years, the distribution network in Chile has undergone various modifications to meet new demands and integrate new technologies. However, these improvements often do not last as long as expected due to inaccurate forecasting, resulting in frequent equipment changes and service interruptions. These issues affect project investment, unsold energy, and penalties for poor quality of supply. Understanding the electricity market, especially in distribution, is crucial and requires linking technical quality standards with service quality factors, such as the frequency and duration of interruptions, to understand their impact on regulated distribution to customers. In this context, a comparative study will be carried out between Long Short-Term Memory (LSTM) and transformer architectures, with the aim of improving the sizing of distribution transformers and preventing failures when determining the nominal power of the transformer to be installed. Variables such as voltages and operating currents of transformers installed between 2020 and 2021 in the Valparaíso region, Chile, along with the type and number of connected customers, maximum and minimum temperatures of the sectors of interest, and seasonality considerations will be used. The compilation of previous studies and the identification of key variables will help to propose solutions based on error percentages to optimise the accuracy of transformer sizing. [ABSTRACT FROM AUTHOR]

High-power ore furnaces mainly use single-phase transformers supplied by phase-to-phase voltage with the secondary winding made in the form of four to eight isolated splits and a high-voltage busbar assembly made of the same number of pairs of tube buses. Due to these design features, turn-to-turn faults are the main faults in the primary winding of the transformer, and flexible coupling breaks and arc faults in splitting circuits prevail in the high-voltage system. This is why current and gas protections are currently used to protect transformers against short circuits. However, current protections are insensitive to turn faults, and the gas protection response time can be long since it strongly depends on the oil temperature. High-current systems are protected from arc faults only by insulating tube buses. However, this insulation is gradually destroyed under the impact of abrasive dust in the air, and the presence of coal dust in the air creates conditions for arc faults. There is no protection against breaks in the circuits of pairs of tube buses. The extent of damage in a transformer and its high-current system due to the faults can be significantly reduced by using new protection devices based on the measurements of the longitudinal and transverse asymmetry of the stray magnetic fields of the protected transformer. To implement these protections, this article suggests a method for protecting a transformer and a high-current system using magnetic current transformers (MCTs). The number and points for MCT winding coils are determined through the analysis of their EMF values versus their positions relative to the windings of the transformer operating under different modes. The results serve as the basis for the protection circuit design; the protection response threshold is calculated, the protection operation is described, and the results of the experiment are given. [ABSTRACT FROM AUTHOR]

According to standards, the harmonic content should be less than 5% at the time of calibration, while the calibration index proposed in this paper stipulates that the primary current amplitude of 1%~120% of the full range of the accuracy level reaches 0.05 S level. In view of the above problems and indexes, this paper adopts the active regulation technology of primary current; firstly, the harmonics of primary current are extracted, and then the opposite harmonic currents are injected by the penetrating wire to offset the harmonics, and finally, charged calibration is carried out. The inductive current transformer charged calibration device was first designed, and the particle swarm algorithm was used to optimize the offset performance of the key link of the background current offset suppression. The transfer function of the offset loop was derived, and it was theoretically analyzed that it can meet the offset requirements up to the 200th harmonic. The results show that the optimized calibration method can realize the full-range calibration of low-voltage inductive current transformers under charged conditions by making a prototype of the device and constructing a test circuit for experiments, and measuring the data and analyzing them. [ABSTRACT FROM AUTHOR]

The DC bias may affect the transient transfer characteristics of the current transformer (CT), threatening the correct action of the relay protection and the safe operation of the power system. Compared with the high voltage direct current (HVDC) transmission in the unipolar-earth loop operation mode and geomagnetically induced current (GIC), the amplitude of the stray current is smaller, and the randomness and fluctuation are larger and accompanied by sudden changes. Combining the characteristics of stray current and the CT equivalent model considering the eddy current loss of the iron core, the mechanism of local transient saturation under the influence of bias magnetization is explained, and the CT saturation phenomenon caused by stray current and its effect on line distance protection are simulated and analyzed. The research shows that the influence of low amplitude and high duration of stray current will make the magnetic flux of CT grow and affect the transmission of steady-state and transient-state so that the measurement impedance appears amplitude-phase shift, which leads to under-range rejection of distance protection. [ABSTRACT FROM AUTHOR]

This paper studies the leader–follower consensus problem for nonlinear multi-agent systems with actuator saturation by adaptive event-triggered scheme. This adaptive mechanism allows parameters in triggered mechanism to change automatically compared to fixed ones in traditional strategies. The paper introduces two distinct approaches to address the issue of saturation. The first approach is sector bounded condition, while the second relies on convex hull representation. Compared with the former one, the latter one can reduce the conservatism of controller design effectively. Furthermore, it is assumed that the nonlinear function adheres to incremental quadratic limitations, thereby offering a more comprehensive depiction of its nonlinear properties. Finally, the validity of the proposed approaches is demonstrated by one numerical example in the background of mechanical systems. • The leader–follower consensus problem for nonlinear multi-agent systems with actuator saturation is studied. • Adaptive event-triggered mechanism for multi-agent systems is considered. • Two methods for dealing with saturation are proposed, one is sector bounded condition and another is convex hull representation. • The nonlinear function is supposed to satisfy incremental quadratic constraints. [ABSTRACT FROM AUTHOR]

This paper studies the control problem for a continuous-time networked system with non-linearity in the state equation as well as in the input, as saturation. The system is considered under denial-of-service (DoS), attacks which cause the blockage of input and/or output components in the overall closed-loop model. An event-triggering scheme that is resilient in nature, along with an observer-based control, has been considered under DoS attacks. The resultant scheme ensures efficient network resources and excludes Zeno behavior naturally due to the presence of a minimum positive interevent delay. Then, an event-based switched non-linear model is presented to address both the event-triggering scheme and the presence of DoS blocking attacks. A piece-wise Lyapunov–Krasovskii functional method on the described non-linear model, resulting in the switched system, is considered for achieving an exponentially stable response by driving the required feasibility conditions. In the presence of a non-linear system with saturation in the actuator, the presented design establishes quantitative relationships among the exponential decay rate, active/sleeping intervals of attacks, parameters of the event-triggering condition, and sampling period of the system. After that, linear matrix inequalities are presented for designing an event-triggered controller with an observer, while the design also includes the region of convergence for dealing with the input non-linearity. Finally, comparative results for an offshore structure model with non-linearity in states as well as in actuator, are demonstrated to verify the results of the control scheme that is developed. It has been verified that our design is less conservative than the previous designs, and can handle the non-linearities in the dynamics of plant and actuator saturation more efficiently, while DoS attacks are also present. By applying our proposed method, the overshoot and undershoot are less than ±2.5 percent, while system states converge to the origin within 55 s. • An ϵ T-Lipschitz condition is used with a scaling factor ϵ and a variable matrix T • Non-linear control designed for system with input saturation and state non-linearity • Stability of the system is ensured in presence of DoS attacks with event triggering • Output feedback is utilized with switching non-linear observer having multiple gains • The joint design of all the required matrices using LK functions is utilized [ABSTRACT FROM AUTHOR]

Copyright of Przegląd Elektrotechniczny is the property of Przeglad Elektrotechniczny and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This article presents the results of an experimental verification of three-phase Dy transformer dynamics under no-load conditions. This study is motivated by previous ferroresonance analyses where the occurrence of inrush currents has been observed. The measurements covered all available electrical quantities in a transient state (12 measured and 3 additionally computed waveforms) during the device's start-up under no-load conditions, as well as in a long-term steady state. A detailed analytical analysis is carried out for the obtained comprehensive set of measurement results. As a result of the conducted research, the mathematical model of the pre-magnetized three-phase Dy transformer is modified. Particular attention is paid to the issue of residual magnetism of the transformer core and its consideration in further research. The original strategy for energizing a three-column three-phase Dy transformer with a suitable pre-magnetization of its columns and original control switching system with a given/set value of the initial phase in the supply voltage is put to the test. The evolution of the induced inrush phenomenon up to the quasi-steady state under given (forced) conditions is documented (currents, voltages and the dynamics of changes taking place in the core (hysteresis loops)). This article represents a continuation of ongoing work on the study of transient states (dynamics of transformer inrush currents). At present, the Dy three-phase transformer is analyzed because of the requirements of industrial operators. [ABSTRACT FROM AUTHOR]

This paper reports on the testing and evaluation of a passive autoranging (AR) method designed to dynamically extend the measurement range of a photonic current transducer (PCT) to pave the way toward a realization of a combined metering- and protection-class current sensor. The PCT utilizes a current transformer (CT), a piezoelectric transducer (PZT), and a fiber Bragg grating (FBG) to enable current measurement at multiple points in an electrical power network whereby multiple sensors are deployed and interrogated serially using a single optical fiber. The autoranging technique relies on incorporating static MOSFET switches to instantaneously short individual serially connected CT burdens in response to a measured current magnitude exceeding pre-set thresholds. The AR circuit switching events produce distinctive signal features that are used by the proposed switching algorithm to apply appropriate scaling factors to reconstruct the measured current from the optical signal. It is shown through laboratory experiments that the AR circuit correctly reacts to pre-set burden current thresholds of 130% of the nominal value and 22 times the nominal value, signifying its "metering" and "protection" range boundaries. The circuit reaction time is below 4 ms, rendering it suitable for standard power system protection purposes. Moreover, the operation of the AR circuit is demonstrated for burden currents of up to 100 A for over 1 s, satisfying a test procedure for the secondary CT circuit, as required by some power system operators. It is demonstrated that the proposed switching algorithm allows for a correct reconstruction of the burden currents from the optical signal acquired by the FBG interrogator, offering the potential to realize a dual-class optical current sensor. [ABSTRACT FROM AUTHOR]

The electrical protection of power networks with fault contribution from inverter-based power sources imposes new application challenges that have to be dealt with by protection engineers. This paper describes the development of a study case model of an HVDC-MMC link for testing the protection behaviour of connected converter transformers. The paper summarises the implementation and validation of the converter control as well as enhancements to provide Fault Ride-Through capability and fast fault current injection as required by the German Technical Connection Rules for HVDC. The grid code standard requires positive- and negative-sequence reactive current injection in the case of grid faults. A Doubled Decoupled Synchronous Reference Frame Phase Locked Loop (DDSRF-PLL) for Vector Current Control (VCC) is implemented. Additionally, a Fault Detection and Fault Ride-Through Reference Generator with a Current Limitation strategy is introduced. Though these techniques are well described in the literature, the DDSRF is improved for current control stability. The relationship between the parameters of the PLL and the control, as well as the behaviour of the protection system, are demonstrated. Grid faults with large voltage dips pose a significant challenge to the stability of the control system. Nevertheless, it is shown that with the developed model, it is possible to make general statements about the protection behaviour in an inverter-based environment. [ABSTRACT FROM AUTHOR]

An online measurement method is proposed in this paper, and a system is established for detecting the excitation impedance of current transformers (CTs) based on Norton's theorem. The theorem is carried out by connecting a resistance and an inductance at the secondary side port of the CT to get the equations for calculating the impedance. The iterative method is used to solve the equations, and the solution is revised to consider the nonlinearity of the core. The main variable in the equations is the variation of the secondary current with the resistance or inductance. To obtain the secondary current variation accurately, which is less than 1‰ of the current, a differential method is proposed, which is based on charging two capacitors and measuring the difference of their voltages instead of measuring each current separately first and then obtaining the current variation by subtraction. This is equivalent to saving two currents first and then measuring the current difference. The differential method avoids the problem of error amplification in the process of measuring two currents separately first and then subtracting them to obtain the current variation and solves the problem that two currents do not appear simultaneously. The results verify the correctness and accuracy of the proposed method and system. The acquisition of the excitation impedance is the basis for obtaining the working characteristics of CT cores, including magnetic and loss characteristics, as well as the error of CTs. [ABSTRACT FROM AUTHOR]