Search

This study focuses on enhancing the strength and water stability of paper straws through a novel approach involving a binary emulsion of lignin-based polyurethane and chitosan. Kraft lignin serves as the raw material for synthesizing a blocked waterborne polyurethane, subsequently combined with carboxylated chitosan to form a stable binary emulsion. The resulting emulsion, exhibiting remarkable stability over at least 6 months, is applied to the base paper. Following emulsion application, the paper undergoes torrefaction at 155 °C. This process deblocks isocyanate groups, enabling their reaction with hydroxyl groups on chitosan and fibers, ultimately forming ester bonds. This reaction significantly improves the mechanical strength and hydrophobicity of paper straws. The composite paper straws demonstrate exceptional mechanical properties, including a tensile strength of 47.21 MPa, Young's modulus of 4.33 GPa, and flexural strength of 32.38 MPa. Notably, its water stability is greatly enhanced, with a wet tensile strength of 40.66 MPa, surpassing commercial paper straws by 8 folds. Furthermore, the composite straw achieves complete biodegradability within 120 days, outperforming conventional paper straws in terms of environmental impact. This innovative solution presents a promising and sustainable alternative to plastic straws, addressing the urgent need for eco-friendly products., Competing Interests: Declaration of competing interest There are no conflicts to declare., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The present investigation sought to assess the practicality of utilizing a combined pre-treatment approach comprising electrocoagulation, peroxide, and hypochlorite treatments for the removal of chemical oxygen demand (COD) and tannin/lignin from paper mill wastewater. The study aimed to optimize the operating parameters with a view to maximizing the removal efficiencies while minimizing energy consumption. A pair of iron electrodes were used as anode and cathode in the study, and the main operating parameters were determined as initial pH, applied current, treatment time and oxidant dosage/COD ratio. Response surface methodology (RSM) was used to evaluate the effect of these parameters on COD and tannin/lignin removals. The primary findings of the investigation indicated that the integration of electrocoagulation with peroxide and hypochlorite treatments exhibited efficacy in removing COD, tannin/lignin, colour, phenol, and turbidity from paper mill wastewater. The optimized conditions resulted in COD removal efficiencies of 48.13 ± 2.2% and 29.53 ± 1.4% for EC with H 2 O 2 and Ca(OCl) 2 , respectively. Tannin/lignin removal efficiencies were 92.59 ± 3.6% and 94.09 ± 1.8% for EC-H 2 O 2 and EC-Ca(OCl) 2 , respectively. The specific energy consumption (SEC) values showed that EC-Ca(OCl) 2 required 7 times more energy than EC-H 2 O 2 for removing 1 kg COD. The principal deduction drawn from the study was that EC-H 2 O 2 pre-treatment demonstrated superior COD removal efficiency and lower energy consumption, while EC-Ca(OCl) 2 pre-treatment exhibited greater efficiency in removing toxic and recalcitrant pollutants. In future studies, it would be useful to conduct research to increase COD removal efficiency in addition to tannin/lignin removal in EC-Ca(OCl) 2 process.

Frequent oceanic oil spill incidents and the discharge of industrial oily wastewaters have caused serious threats to environments, food chains and human beings. Lignin wastes with many reactive groups exist as the byproducts from bioethanol and pulping processing industries, and they are either discarded as wastes or directly consumed as a fuel. To make full use of lignin wastes and simultaneously deal with oily wastewaters, porous lignin-based composites have been rationally designed and prepared. In this review, recent advances in the preparation of porous lignin-based composites are summarized in terms of aerogels, sponges, foams, papers, and membranes, respectively. Then, the mechanisms and the application of porous lignin-based adsorbents and filtration materials for oil/water separation are discussed. Finally, the challenges and perspectives of porous lignin-based composites are proposed in the field of oil/water separation. The utilization of abundant lignin wastes can replace fossil resources, and meanwhile porous lignin-based composites can be used to efficiently treat with oily wastewaters. The above utilization strategy opens an avenue to the rational design and preparation of lignin wastes with high-added value, and gives a possible solution to use lignin wastes in a sustainable and environmentally friendly way., Competing Interests: Declaration of competing interest The authors declare no competing financial interests., (Copyright © 2024 Elsevier B.V. All rights reserved.)

In this study, the potential of ultrafiltered xylano-pectinolytic enzymatic bleaching approach was investigated, for manufacturing wheat straw-based paper. The enzymatic step was found to be most effective, with xylanase-pectinase dose of 4-1.7 IU/g pulp and time period of 180 min. The absorption spectra of the pulp free filtrate samples obtained after treatment of the pulp with ultrafiltered enzymes showed the removal of more impurities, in comparison to the treatment with crude enzymes. Microscopic analysis also showed the removal of lignin impurities in enzymatically bleached pulp samples. This bleaching approach using enzymes resulted in 27% reduction in ClO 2 dose. Ultrafiltered enzymes treated pulp samples also showed improved quality-related parameters, and Gurley porosity, burst index, breaking length, double fold, tear index, and viscosity increased by 19.05, 13.70, 8.18, 29.27, 4.41, and 13.27%, respectively. The lignin content, TDS, TSS, BOD and COD values also decreased in the effluent samples obtained after enzymatic bleaching plus 73% chemical bleaching dose. The BOD and COD values of the effluent samples improved by 23.01 and 23.66%, respectively. Thus, indicating the potential of ultrafiltered xylano-pectinolytic enzymes in reducing pollution during bleaching of wheat straw. This is the first study, mentioning the efficacy of ultrafiltered enzymes in the bleaching of wheat straw-based paper with better optical-strength-related properties and effluent characteristics., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Trees engineered to have less lignin could make paper production less polluting.

The domestication of forest trees for a more sustainable fiber bioeconomy has long been hindered by the complexity and plasticity of lignin, a biopolymer in wood that is recalcitrant to chemical and enzymatic degradation. Here, we show that multiplex CRISPR editing enables precise woody feedstock design for combinatorial improvement of lignin composition and wood properties. By assessing every possible combination of 69,123 multigenic editing strategies for 21 lignin biosynthesis genes, we deduced seven different genome editing strategies targeting the concurrent alteration of up to six genes and produced 174 edited poplar variants. CRISPR editing increased the wood carbohydrate-to-lignin ratio up to 228% that of wild type, leading to more-efficient fiber pulping. The edited wood alleviates a major fiber-production bottleneck regardless of changes in tree growth rate and could bring unprecedented operational efficiencies, bioeconomic opportunities, and environmental benefits.

One of the paper industry's major focuses is shifting toward eco-friendly paper production. Chemical-based bleaching of pulp, which is widely used in the paper industry, is a highly polluting step. Replacing it with enzymatic biobleaching is the most viable alternative to make the process of papermaking greener. Enzymes such as xylanase, mannanase, and laccase are suitable for the biobleaching of pulp, which involves the removal of hemicelluloses, lignins, and other undesirable components. However, as no single enzyme can achieve this, their application in industry is limited. To overcome these limitations, a cocktail of enzymes is required. A number of strategies have been explored for the production and application of a cocktail of enzymes for pulp biobleaching, but no comprehensive information is available in the literature. The present short communication has summarized, compared, and discussed the various studies in this regard, which will be highly useful to pursue further research in this regard and make the process of papermaking greener., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

In present research, a potent fungal strain was isolated from paper mill effluent (black liquor) in order to investigate its potential for the biodegradation of lignin. Two step strategy was used to screen most efficient fungal strain having ability to growin MSM-black liquor medium and to degrade alkali lignin.The results of initial screening indicated that the strain M-2 produced comparatively higher ligninolytic zone on MSN agar plates supplemented with black liquor (BL) and alkali ligninase compared to the other isolates.The results of 18S rRNA gene sequencing revealed that strain M-2 showed ≥ 99% sequence homology with Dipodasceus australiansis.The process for the biodegradation of lignin was optimized using Taguchi Orthogonal Array design. Under optimized conditions of pH 9, 40 °C and 4% inoculum, a maximum of 89% lignin was degraded with 41% color reduction after 8 days of incubation period by Dipodasceus australiansis M-2. The pH and temperature were found to be significant terms with the p-values of 0.002 and 0.001 respectively. The laccase activity of the Dipodascus australiensis was found to be maximum of 1.511 U/mL. The HPLC analysis of lignin biodegradation indicated sharp transformation of peaks as compared to the control. Our results suggested that the strain Dipodascus australiensis M-2 possess excellent lignin degradation and color reduction capability and can be applied in waste treatment systems for pulp and paper mill effluent. In present work we are reporting first hand information regarding biodegradation of lignin by a potent strain of Dipodascus australiensis and statistical optimization of the bioprocess., Competing Interests: Conflict of interest The authors declare that they have no competing interests., (Copyright © 2022 Elsevier GmbH. All rights reserved.)

Chlorine dioxide is widely used for pulp bleaching because of its high delignification selectivity. However, efficient and clean chlorine dioxide bleaching is limited by the complexity of the lignin structure. Herein, the oxidation reactions of phenolic (vanillyl alcohol) and non-phenolic (veratryl alcohol) lignin model species were modulated using chlorine dioxide. The effects of chlorine dioxide concentration, reaction temperature, and reaction time on the consumption rate of the model species were also investigated. The optimal consumption rate for the phenolic species was obtained at a chlorine dioxide concentration of 30 mmol·L -1 , a reaction temperature of 40 °C, and a reaction time of 10 min, resulting in the consumption of 96.3% of vanillyl alcohol. Its consumption remained essentially unchanged compared with that of traditional chlorine dioxide oxidation. However, the consumption rate of veratryl alcohol was significantly reduced from 78.0% to 17.3%. Additionally, the production of chlorobenzene via the chlorine dioxide oxidation of veratryl alcohol was inhibited. The structural changes in lignin before and after different treatments were analyzed. The overall structure of lignin remained stable during the optimization of the chlorine dioxide oxidation treatment. The signal intensities of several phenolic units were reduced. The effects of the selective oxidation of lignin by chlorine dioxide on the pulp properties were analyzed. Pulp viscosity significantly increased owing to the preferential oxidation of phenolic lignin by chlorine dioxide. The pollution load of bleached effluent was considerably reduced at similar pulp brightness levels. This study provides a new approach to chlorine dioxide bleaching. An efficient and clean bleaching process of the pulp was developed.

Lignin is a major by-product of pulp and paper industries, and is resistant to depolymerization due to its heterogeneous structure. Degradation of lignin can be achieved by the use of potential lignin-degrading bacteria. The current study was designed to evaluate the degradation efficiency of newly isolated Bacillus altitudinis SL7 from pulp and paper mill effluent. The degradation efficiency of B. altitudinis SL7 was determined by color reduction, lignin content, and ligninolytic activity from degradation medium supplemented with alkali lignin (3 g/L). B. altitudinis SL7 reduced color and lignin content by 26 and 44%, respectively, on the 5th day of incubation, as evident from the maximum laccase activity. Optimum degradation was observed at 40 °C and pH 8.0. FT-IR spectroscopy and GC-MS analysis confirmed lignin degradation by emergence of the new peaks and identification of low-molecular-weight compounds in treated samples. The identified compounds such as vanillin, 2-methyoxyhenol, 3-methyl phenol, oxalic acid and ferulic acid suggested the degradation of coniferyl and sinapyl groups of lignin. Degradation efficiency of B. altitudinis SL7 towards high lignin concentration under alkaline pH indicated the potential application of this isolate in biological treatment of the lignin-containing effluents.

A lignin-based PU coating was prepared for paper-based green packaging. Two representative diisocyanate were used to prepare the coatings. Due to the rigid aromatic, the physical properties of the TDI system reached the maximum below the lignin content of 40%. The HDI that contains flexible aliphatic chains alleviated the brittleness of coating, and it showed physical advantages when the lignin content was more than 50%. Owing to the high lignin content, the coating presented enhanced thermal stability. After coated with the lignin-based PU coatings, the dry tensile strength of coated paper was improved by 126%. Amazingly, the wet strength was increased from 0.31 to 12.6 MPa with an improvement nearly 40 times. Based on the coordination of lignin, Ag + was introduced into the PU matrix, which imparted the coating with excellent antibacterial ability. The colony forming units of E. coli and S. aureus were both less than 1. However, no inhibition halo was observed, which indicated that the Ag was firmly anchored on the coating and the antibacterial ability is only available when the bacterial contact the coating surface. The lignin-based PU coating with favorable sustainability and properties shows great potential in paper-based green packaging fields., (Copyright © 2021 Elsevier B.V. All rights reserved.)

The pulp and paper industry is a major source of lignocellulose-containing streams. The components of lignocellulose material are lignin, hemicellulose, and cellulose that may be hydrolyzed into their smaller components and used as feedstocks for valorization efforts. Much of this material is contained in underutilized streams and waste products, such as black liquor, pulp and paper sludge, and wastewater. Bacterial fermentation strategies have suitable potential to upgrade lignocellulosic biomass contained in these streams to value-added chemicals. Bacterial conversion allows for a sustainable and economically feasible approach to valorizing these streams, which can bolster and expand applications of the pulp and paper industry. This review discusses the composition of pulp and paper streams, bacterial isolates from process streams that can be used for lignocellulose biotransformations, and technological approaches for improving valorization efforts. KEY POINTS: • Reviews the conversion of pulp and paper industry waste by bacterial isolates. • Metabolic pathways for the breakdown of lignocellulose components. • Methods for isolating bacteria, determining value-added products, and increasing product yields.

Lignocellulosic raw materials are being utilised in many industrial sectors as a natural source of interesting biopolymers. In the present research, tomato plant agri-waste, were subjected to an enzymatic treatment (pectinase, hemicellulase, xylanase and laccase) with the aim of recovering polymeric matrices contained therein and obtain a good quality fibre. The cellulose content in the enzyme-treated fibres was enriched of 25% compared to the untreated, and a fair reduction in hemicellulose and lignin was registered. Morphological analyses at SEM demonstrated the cleanliness and fibrillation of fibres. Moreover, the thermal profile, water absorption and pulp viscosity of fibres was strongly affected by the composition changes. The paperboard manufactured from an enzymatically treated sample showed increased stiffness when subjected to tensile testing respect to the control. Therefore, the use of enzyme in fibre pulping has a potential application in the design of sustainable materials., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Horticultural plant residues (tomato, pepper, and eggplant) were identified as new sources for lignocellulose nanofibers (LCNF). Cellulosic pulp was obtained from the different plant residues using an environmentally friendly process, energy-sustainable, simple, and with low-chemical reagent consumption. The chemical composition of the obtained pulps was analyzed in order to study its influence in the nanofibrillation process. Cellulosic fibers were subjected to two different pretreatments, mechanical and TEMPO(2,2,6,6-Tetramethyl-piperidin-1-oxyl)-mediated oxidation, followed by high-pressure homogenization to produce different lignocellulose nanofibers. Then, LCNF were deeply characterized in terms of nanofibrillation yield, cationic demand, carboxyl content, morphology, crystallinity, and thermal stability. The suitability of each raw material to produce lignocellulose nanofibers was analyzed from the point of view of each pretreatment. TEMPO-mediated oxidation was identified as a more effective pretreatment to produce LCNF, however, it produces a decrease in the thermal stability of the LCNF. The different LCNF were added as reinforcing agent on recycled paperboard and compared with the improving produced by the industrial mechanical beating. The analysis of the papersheets' mechanical properties shows that the addition of LCNF as a reinforcing agent in the paperboard recycling process is a viable alternative to mechanical beating, achieving greater reinforcing effect and increasing the products' life cycles.

Environmental and health concerns are driving the need for new materials in food packaging to replace poly- or perfluorinated compounds, aluminum layers, and petroleum-based polymers. Cellulose nanofibrils (CNF) have been shown by a number of groups to form excellent barrier layers to oxygen and grease. However, the influence of lignin-containing cellulose nanofibrils (LCNF) on film barrier properties has not been well reported. Herein, thin films (16 g/m 2 ) from LCNF and CNF were formed on paper substrates through a filtration technique that should mimic the addition of material at the wet end of a paper machine. Surface, barrier and mechanical attributes of these samples were characterized. The analysis on the surface free energy and water contact angle pointed to the positive role of lignin distribution in inducing a certain degree of water repellency. The observed oxygen transmission rate (OTR) and water vapor permeability (WVP) values of LCNF-coated samples were nearly similar to those with CNF. However, the presence of lignin improved the oil proof performance; these layered designs exhibited an excellent resistance to grease (kit No. 12). The attained papers with LCNF coat were formed into bowl-like containers using metal molds and a facile oven drying protocol to evaluate their resistance to oil penetration over a longer period. The results confirmed the capability of LCNF layer in holding commercially available cooking oils with no evidence of leakage for over five months. Also, an improvement in the tensile strength and elongation at break was observed in the studied papers. Overall, the proposed packaging material possesses viable architecture and can be considered as a fully wood-based alternative for the current fluorocarbon systems.

Biovalorization of pulp and paper activated sludge to value-added products could be an effective alternative to traditional sludge management methods, which tend to pose serious environmental issues. Since pulp and paper activated sludge consists of microbial biomass, cellulose, hemicellulose and lignin and thus, could be subjected to different hydrolysis methods to solubilize sludge solids and release simple sugars to form value-added products by the microbial fermentation process. Hence, different sludge hydrolysis methods have been summarized in this review paper. However, hydrolysis of lignocellulosic materials generates variety of toxic compounds during hydrolysis and causes detrimental effects. Therefore, different toxic compounds and their impact on microorganisms, cellulolytic enzymes and fermentation process have been discussed in detail and recent strategies to counteract the problems of inhibitors have also been briefly explained., (Copyright © 2019 Elsevier Inc. All rights reserved.)

The production of cellulose nanofibers (CNF) usually consist of two different phases. First of all, lignocellulosic fibers need to be treated by means of either chemical, enzymatic or mechanical treatments. Then, in the second phase, the treated lignocellulosic fibers need to be submitted to mechanical fibrillation. This last treatment is usually critical in terms of energy consumption, as well as for providing the appropriate characteristics to the resulting CNF. In the present work, we have investigated the effect of fibrillating lignocellulosic nanofibers (LCNF) made from eucalyptus sawdust by means of high-pressure homogenization and grinding. The obtained results showed that, to achieve the same property level of LCNF, the grinder consumed 12.86 kWh/kg, while the homogenizer, 19.07 kWh/kg, bringing to the light the suitability of grinding for LCNF production. Overall, the present work shows the feasibility of using eucalyptus sawdust, which is a residue from the pulp and paper industry, as raw material for LCNF production, at the same time that brings to the light the relevance of the fibrillation equipment in terms of energy efficiency, approaching the production of LCNF to the industry., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Aims: The utilization of micro-organisms in pulp and paper industries has proved biobleaching technology as an environmentally friendly alternative to the conventional approach. In this paper, the effect of actinobacterial fermentation broth on pulp biobleaching has been investigated., Methods and Results: Actinobacterial colonies were isolated from lignocellulose-rich soil samples and screened for xylanase production and bleaching activity. The most efficient isolate in bleaching activity showed 100% similarity to Streptomyces rutgersensis. Pulp treatment with 5-day fermentation broth of this strain showed up to 7% increase in brightness (30°C for 6 h, pH (5-7)) compared to untreated (control) pulp. Also, after 60 min biotreatment, significant reduction (12·5%) in consumption of bleaching chemicals was achieved to obtain final brightness of 55%., Conclusion: Actinobacterial fermentation broth can be considered as a rich source of effective biobleaching agents which may be considered as environmental friendly and cost-effective technique in comparison with traditional method., Significance and Impact of the Study: Our findings showed ability of S. rutgersensis UTMC 2445 in bleaching chemomechanical paper pulp. Also, two strains of Saccharothrix, a rare actinobacterium, with biobleaching activity were introduced. In the proposed method, there is no need to use purified enzymes, and biobleaching process can be done using the fermentation broth., (© 2019 The Society for Applied Microbiology.)

Sources of pulping red liquor, which is produced by acidic sulfite cooking in paper industry, consisted of lignosulphonate and polysaccharide, commonly considered as waste or byproducts and used in low value, such as surfactant and adhesive are wide and its price is low. Here a novel method for high value-added utilization of the pulp and paper industry waste for fabricating super-swelling biopolymer hydrogels is introduced. In contrast to other costly utilizations, which are needed to separate red liquor or purify hemicellulose and lignin before using, it is first time to directly utilize red liquor to prepare hydrogels without pretreatment. FT-IR, SEM, TGA and XRD are used to determine structure and morphology of hydrogels. It is excited the hydrogels fabricated from acrylic (AA) and industry waste exhibit super-swelling and slow release behaviors in water. Compared with synthetic materials, the hydrogels are at low price to be chosen as candidates for water retention agent for agriculture., (Copyright © 2019. Published by Elsevier B.V.)

The current research intended to explore the hardwood pulps capabilities to produce cellulose (CNPs) and lignocellulose nanopapers (LNPs) and feasible enhancement of their performance for possible utilization in sustainable packaging. The high-yield hardwood pulps were then bleached to show the fundamental role of residual lignin on the ultrafine fibrillation processes, structural and barrier properties of nanopapers. X-ray diffraction results demonstrated that the crystallinity and crystallite size of CNPs and LNPs were lower than the corresponding starting pulps. Field emission scanning electron microscopy analysis showed that the average nanofibril diameter of the CNPs and LNPs are 35 nm and 23 nm, respectively. Elastic modulus of LNPs was found to be 9.1 and 10.8 GPa for Chemimechanical and Neutral sulfite semichemical pulps, respectively. The semi-porous and consolidated structure of LNPs prepared from CMP fibers contributed to yield the lowest water vapor transmission rate i.e. 108 g/m 2 .day which is promising for potential applications in packaging materials., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Lignosulfonates are important by-products of the paper industry and may be transformed into different commodities. We studied the molecular properties of ammonium (LS-AM) and calcium Lignosulfonates (LS-C) and evaluated their bioactivity towards the early development of maize plantlets. The FT-IR, 13 C NMR and 1 H- 13 C-HSQC-NMR spectra showed that the two lignosulfonates varied in hydroxyl, sulfonate and phenolic content, while DOSY-NMR spectroscopy suggested a similar diffusivity. High Performance Size Exclusion Chromatography (HPSEC) was used to simulate the effects of root-exuded acids and describe the conformational dynamics of both LS substrates in acidic aqueous solutions. This technique showed that LS-C was stabilized by the divalent Ca 2+ counterion, thus showing a greater conformational stability than LS-AM, whose components could not be as efficiently aggregated by the monovalent NH4 + counter-ion. The plant bioassays revealed that LS-AM enhanced the elongation of the root system, whereas LS-C significantly increased both total and shoot plant weights. We concluded that the lignosulfonate bioactivity on plant growth depended on the applied concentrations, their molecular properties and conformational stability., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Gold nanoparticles (AuNPs) were directly synthesized and anchored on lignocellulose fiber without an external immobilizing agent via a facile green approach using unbleached kraft (UBK) softwood pulp. The obtained AuNPs were confirmed by UV-vis diffuse reflectance spectroscopy, field-emission scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The antioxidant behavior of the as-prepared AuNP-UBK fiber nanocomposite was evaluated by free radical scavenging of 2,2-diphenyl-1-picrylhydrazyl hydrate (DPPH). The nanocomposite fiber exhibited greatly enhanced radical scavenging activity compared to that of the pure fiber. As a consequence, AuNP-UBK nanocomposite paper showed exceptional antioxidant performance with a radical scavenging rate of over 98%, which is attributed to the synergistic effects of adsorption by the fiber-fiber network and subsequent catalytic activity of the AuNPs. This research indicated that AuNP-UBK fiber nanocomposites could be a new candidate for antioxidant active packaging for use in food preservation., (Copyright © 2017 Elsevier B.V. All rights reserved.)

A novel lignin-based flocculant (LBF) with superior flocculation performance was prepared from paper mill sludge in this work. The functional groups of LBF and alkaline lignin (AL) were determined by Fourier transform infrared spectroscopy (FTIR). The flocculation performance of LBF integrated with polyaluminum chloride (PAC) was tested in reactive dye wastewater treatment. Floc properties and color removals in multiple flocculation systems were discussed. Results indicated that the dye removal (93%) was greatly facilitated as the LBF was integrated with PAC (PAC + LBF). In addition, floc properties and color removals were significantly improved in the presence of Ca 2+ and Mg 2+ . In contrary, flocculation performance was greatly restricted in the presence of SO 4 2- . LBF was less pH sensitive and shear sensitive than polyacrylamide (PAM) due to the enhanced charge neutralization and bridging action. On the basis of that, LBF could be used as a promising flocculant in dye wastewater treatment.

In the present work, lignocellulosic micro/nanofibers (LCMNF) were produced from pine sawdust. For that, pine sawdust was submitted to alkali treatment and subsequent bleaching stages, tailoring its chemical composition with the purpose of obtaining effective LCMNF. The obtained LCMNF were characterized and incorporated to recycled cardboard boxes with the purpose of producing recycled paper. The obtained results showed that it was possible to obtain LCMNF with the same reinforcing potential than those cellulose nanofibers (CNF) prepared by oxidative or other chemical methods In fact, the obtained papers increased the breaking length of recycled cardboard from 3338m to 5347m, being a value significantly higher than the requirements to produce paper bags. Overall, the studied strategies could allow a significant reduction of paper basis weight, with the consequent material saving and, thus, contribution to the environment., (Copyright © 2017 Elsevier B.V. All rights reserved.)

Lignin in chemical pulping waste, or black liquor (BL), can be converted into various products via supercritical water gasification (SCWG). However, the inherited alkaline contents from the pulping chemicals may affect the product yields and properties. In this research, the influence of the residual alkali on the product distribution via SCWG of soda BL and kraft BL was evaluated. The SCWG was performed in a batch quartz reactor for 10 min at various temperatures (673, 773 and 873 K) and pressures (250, 300 and 400 bar). The highest hydrogen (H 2 ) production occurred at 873 K for the soda BL. The water-gas shift reaction with sodium ions played an important part in the H 2 production, while only small amounts of methane and carbon monoxide were detected. Hydrocarbons, carboxylic acids and esters were the dominant substrates in the liquid products, which denoted the potential of this method for bond cleaving of the lignin macromolecule. As a result, BL, which typically contains alkali salt, was an appropriate feedstock for the SCWG reaction to produce renewable fuel. This method not only has a positive influence on the generation of value added products from highly corrosive waste but also helps avoid some technical problems commonly encountered with direct firing in a recovery boiler.

Lignin is the second most abundant biopolymer after cellulose. It has long been obtained as a by-product of cellulose production in pulp and paper production, but had rather low added-value applications. A changing paper market and the emergence of biorefinery projects should generate vast amounts of lignin with the potential of value addition. Nanomaterials offer unique properties and the preparation of lignin nanoparticles and other nanostructures has therefore gained interest as a promising technique to obtain value-added lignin products. Due to lignin's high structural and chemical heterogeneity, methods must be adapted to these different types. This review focuses on the ability of different formation methods to cope with the huge variety of lignin types and points out which particle characteristics can be achieved by which method. The current research's main focus is on pH and solvent-shifting methods where the latter can yield solid and hollow particles. Solvent shifting also showed the capability to cope with different lignin types and solvents and antisolvents, respectively. However, process conditions have to be adapted to every type of lignin and reduction of solvent demand or the integration in a biorefinery process chain must be focused., Competing Interests: The authors declare no conflict of interest.

Anaerobic digestion (AD) of lignocellulosic materials is commonly limited by the hydrolysis step. Unlike unprocessed lignocellulosic materials, paper and paper board (PPB) are processed for their fabrication. Such modifications may affect their methane yields and methane production rates. Previous studies have investigated the correlation between lignin and biomethane yields of unprocessed lignocellulosic materials; nevertheless, there is limited knowledge regarding the relationship between the AD kinetic parameters and composition of PPB. This study evaluated correlations of methane yields and Monod and Gompertz kinetic parameters with structural carbohydrates, lignin, and ash concentration of five types of PPBs. All components were used as single and combined independent variables in linear regressions to predict methane yield, maximum specific methanogenic activity (SMA max ), saturation constant (K s ), and lag phase (λ). Additionally, microbial community profiles were obtained for each PPB assay. Results showed methane yields ranging from 69.2 ± 8.61 to 97.2 ± 2.29% of PPB substrates provided. The highest correlation coefficients were obtained for SMA max as function of hemicellulose/(lignin + ash) (R 2  = 0.86) and for λ as a function of lignin + cellulose (R 2  = 0.85). All other parameters exhibited weaker correlations (R 2  ≤ 0.77). Relative abundance analyses revealed no major changes in the community profile for each of the substrates evaluated. The overall findings of this study are: (i) combinations of structural carbohydrates, lignin, and ash used as ratios of degradable to either non-degradable or slowly degradable fractions predict AD kinetic parameters of PPB materials better than single independent variables; and (ii) other components added during their fabrication may also influence both methane yield and kinetic parameters. Biotechnol. Bioeng. 2017;114: 951-960. © 2016 Wiley Periodicals, Inc., (© 2016 Wiley Periodicals, Inc.)

Integrated forest biorefinery offers promising pathways to sustainably diversify the revenue of pulp and paper industry. In this context, lignin can be extracted from a residual stream of Kraft pulping process, called black liquor, and subsequently converted into a wide spectrum of bio-based products. Electrochemical acidification of Kraft black liquor by electrodialysis with bipolar membrane results in lignin extraction and caustic soda production. Even though the implementation of this method requires less chemicals than the chemical acidification process, fouling of the ion exchange membranes and especially bipolar membrane impairs its productivity. Membrane thickness and ash content measurements along with scanning electron microscopy (SEM), elemental analysis (EDX) and X-ray photoelectron spectrometry (XPS) analysis were performed to identify the nature and mechanisms of the membrane fouling. The results revealed that the fouling layer mostly consisted of organic components and particularly lignin. Based on our proposed fouling mechanisms, throughout the electrodialysis process the pH of the black liquor gradually decreased and as a result more proton ions were available to trigger protonation reaction of lignin phenolic groups and decrease the lignin solubility. Due to the abundance of the proton ions on the surface of the cation exchange layers of the bipolar membrane, destabilized lignin macro-molecules started to self-aggregate and formed lignin clusters on its surface. Over the time, these lignin clusters covered the entire surface of the bipolar membrane and the spaces between the membranes and, eventually, attached to the surface of the cation exchange membrane., (Copyright © 2016 Elsevier Inc. All rights reserved.)

Xylanase is commonly applied in pulp and paper industries to ease cost-related and environmental pressures. The effect of xylanase treatment on pulp bleaching is well-established, however, few studies were conducted on the effects of xylanase treatment in pulp yellowing, especially the mechanism of pulp yellowing inhibition by xylanase treatment. In this study, pure xylanase (EC 3.2.1.8) was applied to treat wheat straw chemical pulp (CP) and poplar chemi-thermo-mechanical pulp (CTMP) to determine their effects on pulp brightness and on light- and heat-induced yellowing. The xylanase treatment decreased the post-color number of the pulps during light- and heat-induced yellowing. However, differences were observed in the yellowing inhibition between the wheat straw CP and poplar CTMP. The changes in chemical components of pulps after the xylanase treatment, for example, lignin, hemicellulose, and HexA contents, and analysis of UV-vis absorption spectra and Fourier transform infrared-attenuated total reflectance spectrum were used to explore the pulp yellowing inhibition causes by the xylanase treatment.

In this work, to elucidate why the acid-pretreated bamboo shows disappointingly low enzymatic digestibility comparing to the alkali-pretreated bamboo, residual lignins in acid-pretreated and kraft pulped bamboo were isolated and analyzed by adsorption isotherm to evaluate their extents of nonproductive enzyme adsorption. Meanwhile, physicochemical properties of the isolated lignins were analyzed and a relationship was established with non-productive adsorption. Results showed that the adsorption affinity and binding strength of cellulase on acid-pretreated bamboo lignin (MWLa) was significantly higher than that on residual lignin in pulped bamboo (MWLp). The maximum adsorption capacity of cellulase on MWLp was 129.49 mg/g lignin, which was lower than that on MWLa (160.25 mg/g lignin). When isolated lignins were added into the Avicel hydrolysis solution, the inhibitory effect on enzymatic hydrolysis efficiency of MWLa was found to be considerably stronger than that with MWLp. The cellulase adsorption on isolated lignins was correlated positively with hydrophobicity, phenolic hydroxyl group, and degree of condensation but negatively with surface charges and aliphatic hydroxyl group. These results suggest that the higher nonproductive cellulase adsorption and physicochemical properties of residual lignin in acid-pretreated bamboo may be responsible for its disappointingly low enzymatic digestibility.

Lignocellulose biomass predominantly constitutes the main feedstock for pulp and paper industry. Though some products of pulp and paper industry require the presence of lignin content, for most of the useful products formation lies in the efficient and selective removal of lignin component to make use of the intact cellulose fraction during the pretreatment of pulp. Lignin is a recalcitrant heteropolymer comprised of several complex stable bonds and linkages. The chemicals or intense energy processes used for delignification process release the hazardous chemicals compounds in the wastewater which cause toxicity and environmental pollution. The implementation of bacterial species has elucidated an effective approach in the generation of value-added products while degrading lignin from pulp biomass as well as detoxification of effluent. The direct use of bacterial cells in lignocellulose biomass and wastewater streams is promising as it outperforms the practical and technical constraints largely confronted by fungal and enzymatic means. The present review paper thus unleashed the potential of ligninolytic bacteria towards delignification of pulp biomass and treatment of effluent together with bioconversion of biomass and lignin into value-added products. Graphical abstract Schematic illustration of potential possible contribution of ligninolytic bacteria towards pulp and paper industry.

Wastewater containing kraft lignin (KL) discharged from pulp and paper industries could cause serious environmental contamination. Appropriate effluent treatment is required to reduce the pollution. Investigations on anaerobic bacteria capable of degrading KL are beneficial to both lignin removal and biofuel regeneration from the effluent. In this paper, an anaerobic strain capable of degrading KL was isolated from the sludge of a pulp and paper mill and identified as Dysgonomonas sp. WJDL-Y1 by 16S rRNA analysis. Optimum conditions for KL degradation by strain WJDL-Y1 were obtained at initial pH of 6.8, C:N ratio of 6 and temperature of 33°C, based on statistical analyses by response surface methodology. For a 1.2 g/l KL solution, a COD removal rate of 20.7% concomitant with biomass increase of 17.6% was achieved after 4 days of incubation under the optimum conditions. After the treatment by strain WJDL-Y1, KL was modified and degraded.

Stigmasterol is a phytosterol contained in Kraft mill effluent that is able to increase over 100% after aerobic biological treatment. This compound can act as an endocrine disrupter as its structure is similar to that of cholesterol. The aim of this study was to evaluate the removal of stigmasterol from Kraft mill effluents treated by a moving bed biofilm reactor (MBBR) with steroidal metabolite detection. The MBBR was operated for 145 days, with a hydraulic retention time of 2 days. Stigmasterol and steroidal metabolites were detected by gas chromatography with a flame ionization detector during MBBR operation. The results show that the MBBR removed 87.4% of biological oxygen demand (BOD5), 61.5% of chemical oxygen demand (COD), 24.5% of phenol and 31.5% of lignin, expressed in average values. The MBBR system successfully removed 100% of the stigmasterol contained in the influent (33 µg L(-1)) after 5 weeks of operation. In that case, the organic load rate was 0.343 kg COD m(-3) d(-1). Furthermore, different steroidal compounds (e.g., testosterone propionate, stigmast-4-en-3-one, 5α-pregnan-12-one-20α-hydroxy, 5α-pregnane-3,11,20-trione and 3α-hydroxy-5α-androstane-11,17-dione were detected in the Kraft mill effluent as potential products of phytosterol biotransformation.

This paper presents the technical-economic and environmental assessment of four lignin extraction processes from two different raw materials (sugarcane bagasse and rice husks). The processes are divided into two categories, the first processes evaluates lignin extraction with prior acid hydrolysis step, while in the second case the extraction processes are evaluated standalone for a total analysis of 16 scenarios. Profitability indicators as the net present value (NPV) and environmental indicators as the potential environmental impact (PEI) are used through a process engineering approach to understand and select the best lignin extraction process. The results show that both economically and environmentally process with sulfites and soda from rice husk presents the best results; however the quality of lignin obtained with sulfites is not suitable for high value-added products. Then, the soda is an interesting option for the extraction of lignin if high quality lignin is required for high value-added products at low costs., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

The aim of this work was to study the impact of shortening kraft pulping (KP) process integrated with extended oxygen delignification (OD) on the biorefinery process performance of eucalyptus. Data showed that using kraft pulps with high kappa number could improve the delignification efficiency of OD, reduce hexenuronic acid formation in kraft pulps. Pulp viscosity for a target kappa number of ∼10 was comparable to that obtained from conventional KP and OD process. The energy and alkali consumption in the integrated biorefinery process could be optimized when using a KP pulp with kappa number of ∼27. The process could minimize the overall methanol formation, but greater amounts of carbonate and oxalate were formed. The information from this study will be helpful to the future implementation of short-time KP integrated with extended OD process in actual pulp mill applications for biorefinery, aiming at further improvement in the biorefinery effectiveness of hardwood., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Fines concentration harms paper machine runability and output quality in recovered paper processing, hence, their extraction would be fundamentally beneficial. In this study, separated fines from an industrial recycled fiber pulp (RFP) were characterized and evaluated for their potential biogas yields with a focus on understanding the role of varying lignin and ash contents. Further, these results were compared with biogas yields from conventional chemical and mechanical pulps. Overall, methane yields of fines from mechanical pulps (21-28mL/gVS) and RFP (127mL/gVS) are relatively low compared to the high methane yields of 375mL/gVS from the chemical pulp fines. However, it was shown that the high ash content in RFP fines (up to 50%) did not negatively influence overall yield, rather, it was the presence of slowly biodegrading lignin-rich fiber fines., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Unlabelled: An anaerobic kraft lignin (KL)-degrading bacterial strain was isolated from sludge of a pulp and paper mill. It was characterized as Acetoanaerobium sp. WJDL-Y2 by 16S rRNA gene sequencing. The maximum KL degradation capability of strain Y2 was determined to be 24·9% on a COD basis under an optimal condition with temperature of 31·5°C, initial pH of 6·8 and KL to nitrogen (as NH4 Cl) ratio of 6·5 by mass. Growth kinetic studies showed that the KL tolerance of strain Y2 was relatively high (Ki  = 8120·45 mg l(-1) ). Analysing KL degradation products by GC-MS revealed the formation of low-molecular-weight aromatic compounds (LMWACs), including benzene-propanoic acid, syringic acid and ferulic acid. This indicates that strain Y2 can oxidize lignin structure's p-hydroxyphenyl (H) units, guaiacyl (G) units and syringyl (S). In addition, the inoculated sample also contained low-molecular acid compounds, such as hexanoic acid, adipic acid and 2-hydroxybutyric acid, further validating strain Y2's ability to degrade KL., Significance and Impact of the Study: Kraft lignin containing effluents discharged from pulp and paper industries causes serious environmental pollution in developing countries. Due to the immense environmental adaptability and biochemical versatility, bacterial ligninolytic potential deserve to be studied for application in effluent treatment of pulp and paper industry. In this study, an anaerobic lignin-degrading bacterium, Acetoanaerobium sp. WJDL-Y2 (accession no. KF176997),was isolated from the sludge of a pulp and paper mill. Strain Y2 can play an important role in treating pulp and paper wastewater, as well as breaking down materials for biofuel and chemical production., (© 2015 The Society for Applied Microbiology.)

The potential of cellulase enzymes in the developing and ongoing "biorefinery" industry has provided a great motivation to develop an efficient cellulase mixture. Recent work has shown how important the role that the so-called accessory enzymes can play in an effective enzymatic hydrolysis. In this study, three newest Novozymes Cellic CTec cellulase preparations (CTec 1/2/3) were compared to hydrolyze steam pretreated lignocellulosic substrates and model substances at an identical FPA loading. These cellulase preparations were found to display significantly different hydrolytic performances irrelevant with the FPA. And this difference was even observed on the filter paper itself when the FPA based assay was revisited. The analysis of specific enzyme activity in cellulase preparations demonstrated that different accessory enzymes were mainly responsible for the discrepancy of enzymatic hydrolysis between diversified substrates and various cellulases. Such the active role of accessory enzymes present in cellulase preparations was finally verified by supplementation with β-glucosidase, xylanase and lytic polysaccharide monooxygenases AA9. This paper provides new insights into the role of accessory enzymes, which can further provide a useful reference for the rational customization of cellulase cocktails in order to realize an efficient conversion of natural lignocellulosic substrates., (Copyright © 2015 Elsevier Inc. All rights reserved.)

The effectiveness of a biorefinery based on an HWE-Kraft-ECF bleaching process and the end use of pulp was systematically evaluated. Using a P-factor of 198, nearly 30% of xylan-based sugars were recovered. The resulting pulp and paper properties were found to be comparable with the control. A maximum xylan-based sugar recovery of nearly 50% was achieved at a P-factor of 738. Although the strength of this P-factor induced handsheet was lower than that of the control by about 20%, the corresponding pulp was sufficient for dissolving pulp application. However, once the P-factor rose above 1189, hemicellulose sugars were significantly degraded into furans; pulp and paper properties were also deteriorated due to cellulose degradation, lignin deposition and condensation. Thus, considering the different end use of pulps, the performance of an HWE-based biorefinery could be balanced by its HWE severity., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

To understand the applicability of the termination indicators for landfill municipal solid waste (MSW) with low initial lignin content, four different accelerated landfill stabilization techniques were applied to anaerobic landfilled waste, including anaerobic flushing with water, anaerobic flushing with Fenton-treated leachate, and aerobic flushing with Fenton-treated and UV/H2O2-treated leachate. Termination indicators, including total organic carbon (TOC), ammonia-N (NH4(+)-N), the ratio of UV absorbance at 254 nm to TOC concentration (SUVA254), fluorescence spectra of leachate, methane production, oxygen consumption, lignocellulose content, and humus-like content were evaluated. Results suggest that oxygen consumption related indicators used as a termination indicator for low-lignin-content MSW were more sensitive than methane consumption related indicators. Aeration increased humic acid (HA) and (HA+FA)/HyI content by 2.9 and 1.7 times compared to the anaerobically stabilized low-lignin-content MSW. On the other hand, both the fulvic acid (FA) and hydrophilic (HyI) fractions remained constant regardless of stabilization technique. The target value developed for low-lignin-content MSW was quite different than developed countries mainly due to low residual biodegradable organic carbon content in stabilized low-lignin-content MSW., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

This study evaluated steam (SE) explosion on the saccharification and simultaneous saccharification and fermentation (SSF) of waste copier paper. SE resulted in a colouration, a reduction in fibre thickness and increased water absorption. Changes in chemical composition were evident at severities greater than 4.24 resulting in a loss of xylose and the production of breakdown products known to inhibit fermentation (particularly formic acid and acetic acid). SE did not improve final yields of glucose or ethanol, and at severities 4.53 and 4.83 reduced yields probably due to the effect of breakdown products and fermentation inhibitors. However, at moderate severities of 3.6 and 3.9 there was an increase in initial rates of hydrolysis which may provide a basis for reducing processing times. Co-steam explosion of waste copier paper and wheat straw attenuated the production of breakdown products, and may also provide a basis for improving SSF of lignocellulose., (Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Transforming plant biomass to biofuel is one of the few solutions that can truly sustain mankind's long-term needs for liquid transportation fuel with minimized environmental impact. However, despite decades of effort, commercial development of biomass-to-biofuel conversion processes is still not an economically viable proposition. Identifying value-added co-products along with the production of biofuel provides a key solution to overcoming this economic barrier. Lignin is the second most abundant component next to cellulose in almost all plant biomass; the emerging biomass refinery industry will inevitably generate an enormous amount of lignin. Development of selective biorefinery lignin-to-bioproducts conversion processes will play a pivotal role in significantly improving the economic feasibility and sustainability of biofuel production from renewable biomass. The urgency and importance of this endeavor has been increasingly recognized in the last few years. This paper reviews state-of-the-art oxidative lignin depolymerization chemistries employed in the papermaking process and oxidative catalysts that can be applied to biorefinery lignin to produce platform chemicals including phenolic compounds, dicarboxylic acids, and quinones in high selectivity and yield. The potential synergies of integrating new catalysts with commercial delignification chemistries are discussed. We hope the information will build on the existing body of knowledge to provide new insights towards developing practical and commercially viable lignin conversion technologies, enabling sustainable biofuel production from lignocellulosic biomass to be competitive with fossil fuel., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Next to xylanases, laccases from fungi and alkali-tolerant bacteria are the most important biocatalysts that can be employed for eco-friendly biobleaching of hard and soft wood pulps in the paper industry. Laccases offer a potential alternative to conventional, environmental-polluting chlorine and chlorine-based bleaching and has no reductive effect on the final yield of pulp as compared to hemicellulases (xylanases and mannanases). In the last decade, reports on biobleaching with laccases are based on laboratory observations only. There are several critical challenges before this enzyme can be implemented for pulp bleaching at the industrial scale. This review discusses significant factors like redox potential, laccase mediator system (LMS)-synthetic or natural, pH, temperature, stability of enzyme, unwanted grafting reactions of laccase, and cost-intensive production at large scale which constitute a great hitch for the successful implementation of laccases at industrial level.

The white-rot fungi Irpex lacteus KB-1.1 and Lentinus tigrinus LP-7 have been shown in previous studies to have high biobleaching activity in vivo. The aim of this study was to investigate the activities and stabilities of extracellular enzymes, prepared from I. lacteus and L. tigrinus culture grown in three types of economical media of agricultural and forestry wastes, for biobleaching of Acacia oxygen-delignified kraft pulp using kappa number reduction as an indicator of delignification. After 3 days of incubation, the extracellular enzymes preparations from I. lacteus and L. tigrinus cultures in media of Acacia mangium wood powder supplemented with rice bran and addition 1 % glucose (WRBG), resulted in significant decrease of 4.4 and 6.7 %, respectively. A slightly higher kappa number reduction (7.4 %) was achieved with the combine extracellular enzymes from I. lacteus and L. tigrinus. One of the strategies for reducing the cost of enzyme production for treatment processes in the pulp and paper industry is the utilization of agricultural and forestry waste. Thus, WRBG has potential as a culture medium for producing stable lignolytic enzymes simply and economically.

Treating ground bagasse or Southern yellow pine in the biodegradable ionic liquid (IL), choline acetate ([Cho][OAc]), at 100°C for 24h led to dissolution of hemicellulose and lignin, while leaving the cellulose pulp undissolved, with a 54.3% (bagasse) or 34.3% (pine) reduction in lignin content. The IL solution of the dissolved biopolymers can be separated from the undissolved particles either by addition of water (20 wt% of IL) followed by filtration or by centrifugation. Hemicellulose (19.0 wt% of original bagasse, 10.2 wt% of original pine, containing 14-18 wt% lignin) and lignin (5.0 wt% of original bagasse, 6.0 wt% of original pine) could be subsequently precipitated. The pulp obtained from [Cho][OAc] treatment can be rapidly dissolved in 1-ethyl-3-methylimidazolium acetate (e.g., 17 h for raw bagasse vs. 7h for pulp), and precipitated as cellulose-rich material (CRM) with a lower lignin content (e.g., 23.6% for raw bagasse vs. 10.6% for CRM)., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Lignin removal is essential for value-added utilization of hemicelluloses and acetic acid present in the prehydrolysis liquor (PHL) of a kraft-based hardwood dissolving pulp production. In this paper, a novel process concept, consisting of laccase-induced lignin polymerization, followed by filtration/flocculation, was developed to enhance the lignin removal. The results showed that the lignin removal increased from 11% to 46-61% at laccase concentration of 1-4 U mL(-1). The GPC results showed that the molecular weight of the lignin from the laccase treated PHL was increased by 160% in comparison with the original one. The subsequent flocculation using singular Poly-DADMAC system or dual polymer system of Poly-DADMAC/CPAM can further remove 10-15% lignin. The concentrations of hemicelluloses and acetic acid were negligibly affected during the laccase treatment, while flocculation caused 12-15% of total sugar loss. Additionally, the process incorporates this new concept into the kraft-based dissolving pulp production process was proposed., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

The spent liquor (SL) of a neutral sulfite semichemical pulping process contains lignocelluloses that are currently treated in a waste water system. In this work, an adsorption process using activated carbon (AC) was considered for isolating the lignin and hemicelluloses from SL. The maximum adsorptions of 0.9 g/g lignin and 0.43 g/g of hemicelluloses on AC were achieved under the conditions of 30°C, pH 7 and 3h with SL/AC weight ratio of 90. The addition of polydiallyldimethylammonium chloride (PDADMAC) to the SL/AC system significantly improved the adsorption of lignin to 2.5 g/g on AC. The molecular weight of PDADMAC considerably affected the results in that the higher MW PDADMAC led to less lignin, but more hemicelluloses, turbidity and chemical oxygen demand removals from the SL. The thermal analysis also revealed that the higher MW PDADMAC generated precipitates with a lower incineration temperature and heating value., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Hemicelluloses and lignin present in the spent liquor (SL) of neutral sulfite semichemical (NSSC) pulping process can potentially be converted into value-added products such as furfural, hydroxymethylfurfural, levulinic acid, phenols and adhesives. However, the direct conversion of hemicelluloses and lignin of SL into value-added products is uneconomical due to the dilute nature of the SL. To have a feasible downstream process for utilizing lignocelluloses of SL, the lignocelluloses should initially be separated from the SL. In this study, an adsorption process (via applying activated carbon) was considered for isolating the dissolved lignin and hemicelluloses from the SL of an NSSC pulping process. Under the optimal conditions of pH, SL/AC weight ratio, time and temperature of 5.7, 30, 360 min and 30 °C, the maximum lignin and hemicellulose adsorptions were 0.33 and 0.25 g/g on AC. The chemical oxygen demand (COD) and turbidity of the SL were decreased by 11% and 39%, respectively, as a result of lignocellulose adsorption on AC. Also, the incineration behavior of the SL-treated AC was studied with a thermo-gravimetric analysis (TGA)., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Industrial discharge has tremendously increased inorganic pollutants in water bodies all over the world. Paper and pulp effluent is included in one of the most pollution generating discharges containing complex chemical compounds such as lignin. For clean and healthy water resources, the recovery of lignin from wastewater from the paper and pulp industry is of high importance. Available chemical and biological technologies for removal of lignin have certain drawbacks. Coagulation and flocculation is not only the economic but also the effective method for removal of lignin. The present review highlights available coagulants employed for removal of lignin from paper and pulp wastewater. Each coagulant is pH dependent and shows varied results with change in effluent characteristics. The hydrolysis products of aluminium-based coagulants, iron-based coagulants and copper sulphate have positive charges. These positive charges promote formation of flocs through charged neutralisation or sweep flocculation. In the case of titanium-based coagulants, hydrolysis product is negatively charged and mode is heterocoagulation. Ninety percent recovery of lignin is achieved by using a mixture of oxotitanium sulphate and aluminium sulphate and 80% with aluminium sulphate. Virtually complete recovery of lignin is observed with oxotitanium sulphate.

The present work deals with application of hydrodynamic cavitation for intensification of delignification of wheat straw as an essential step in the paper manufacturing process. Wheat straw was first treated with potassium hydroxide (KOH) for 48 h and subsequently alkali treated wheat straw was subjected to hydrodynamic cavitation. Hydrodynamic cavitation reactor used in the work is basically a stator and rotor assembly, where the rotor is provided with indentations and cavitational events are expected to occur on the surface of rotor as well as within the indentations. It has been observed that treatment of alkali treated wheat straw in hydrodynamic cavitation reactor for 10-15 min increases the tensile index of the synthesized paper sheets to about 50-55%, which is sufficient for paper board manufacture. The final mechanical properties of the paper can be effectively managed by controlling the processing parameters as well as the cavitational parameters. It has also been established that hydrodynamic cavitation proves to be an effective method over other standard digestion techniques of delignification in terms of electrical energy requirements as well as the required time for processing. Overall, the work is first of its kind application of hydrodynamic cavitation for enhancing the effectiveness of delignification and presents novel results of significant interest to the paper and pulp industry opening an entirely new area of application of cavitational reactors., (Copyright © 2013 Elsevier B.V. All rights reserved.)