Search

Updating of the current Urban Waste Water Treatment Directive (91/271/EEC) will demand stricter regulations for nutrients removal. In this frame, wastewater treatment plants (WWTPs) of small-to-medium potential will face new challenges for achieving process intensification. Integrating intermittent aeration (IA) and integrated fixed-film activated sludge (IFAS) technologies could be a promising solution to meet such requirements. This study analyzed how IA cycles affected nutrients removal in IFAS reactors with different biofilm carriers (e.g., plastic and sponge media). The plants responses to different carbon/nitrogen/phosphorous (C/N/P) ratios were evaluated while operating under low sludge retention time (SRT) to simulate overloaded conditions. A short IA cycle (1 h) with an aeration/not aeration ratio of 2:1 enabled high organic carbon and nitrification performances when operating at high C/N/P (11.8/1/1), whereas low denitrification and phosphorous removal yields were obtained because of the short not-aerated phase. Decreasing C/N ratio (8.8/1/1) without changing the IA cycle resulted in nitrification worsening because of the reduced metabolic kinetics of biofilm. Under such load conditions, a higher IA cycle (2 h) was necessary to improve process performance. A longer not-aerated phase was also positive for denitrification and phosphorous removal because of the establishment of anoxic and anaerobic environments within the bulk and inner biofilm layers. Besides, results suggested that sponge carriers offered advantages over plastic ones, enabling a higher biofilm retention capacity, better nutrient removal, as well as robustness and resilience to operating condition changes. This would result in simpler management systems for implementing the IA process, thus reducing process complexity and costs., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The present study has focused on the mainstream integration of polyhydroxyalkanoate (PHA) production with industrial wastewater treatment by exploiting three different technologies all operating in sequencing batch reactors (SBR): conventional activated sludge (AS-SBR), membrane bioreactor (AS-MBR) and aerobic granular sludge (AGS). A full aerobic feast/famine strategy was adopted to obtain enrichment of biomass with PHA-storing bacteria. All the systems were operated at different organic loading (OLR) rate equal to 1-2-3 kgCOD/m 3 ∙d in three respective experimental periods. The AS-MBR showed the better and stable carbon removal performance, whereas the effluent quality of the AS-SBR and AGS deteriorated at high OLR. Biomass enrichment with PHA-storing bacteria was successfully obtained in all the systems. The AS-MBR improved the PHA productivity with increasing OLR (max 35% w/w), whereas the AS-SBR reduced the PHA content (max 20% w/w) above an OLR threshold of 2 kgCOD/m 3 ∙d. In contrast, in the AGS the increase of OLR resulted in a significant decrease in PHA productivity (max 14% w/w) and a concomitant increase of extracellular polymers (EPS) production (max 75% w/w). Results demonstrated that organic carbon was mainly driven towards the intracellular storage pathway in the AS-SBR (max yield 51%) and MBR (max yield 61%), whereas additional stressors in AGS (e.g., hydraulic selection pressure, shear forces) induced bacteria to channel the COD into extracellular storage compounds (max yield 50%) necessary to maintain the granule's structure. The results of the present study indicated that full-aerobic feast/famine strategy was more suitable for flocculent sludge-based technologies, although biofilm-like systems could open new scenarios for other biopolymers recovery (e.g., EPS). Moreover, the AS-MBR resulted the most suitable technology for the integration of PHA production in a mainstream industrial wastewater treatment plant, considering the greater process stability and the potential reclamation of the treated wastewater., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The present study investigated the combined production of reclaimed water for reuse purposes and polyhydroxyalkanoates (PHA) from an agro-food industrial wastewater. A pilot plant implementing a two-stage process for PHA production was studied. It consisted of a mainstream sequencing batch membrane bioreactor (SBMBR) in which selection of PHA-accumulating organisms and wastewater treatment were carried out in, and a side-stream fed-batch reactor (FBR) where the excess sludge from the SBMBR was used for PHA accumulation. The performance of the SBMBR was compared with that of a conventional sequencing batch reactor (SBR) treating the same wastewater under different food to microorganisms' ratios (F/M) ranging between 0.125 and 0.650 kgCOD kgTSS -3 d -1 . The SBMBR enabled to obtain very high-quality effluent in compliance with the relevant national (Italy) and European regulations (Italian DM 185/03 and EU, 2020/741) in the field of wastewater reclamation, whereas the performances in the SBR collapsed at F/M higher than 0.50 kgCOD kgTSS -1 d -1 . A maximum intracellular storage of 45% (w/w) and a production yield of 0.63 gPHA L -1 h -1 were achieved when the SBMBR system was operated with a F/M ratio close to 0.50 kgCOD kgTSS -1 d -1 . This resulted approximately 35% higher than those observed in the SBR, since the ultrafiltration membrane avoided the washout of dispersed and filamentous bacteria capable of storing PHA. Furthermore, while maximizing PHA productivity in conventional SBR systems led to process dysfunctions, in the SBMBR system it helped mitigate these issues by reducing membrane fouling behaviour. The results of this study supported the possibility to achieve combined recovery of reclaimed water and high-value added bioproducts using membrane technology, leading the way for agro-food industrial wastewater valorization in the frame of a circular economy model., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

In the present research, insights about the mechanisms of excess sludge minimization occurring in an oxic-settling-anaerobic (OSA) were provided. The investigation involved two systems operating in parallel. In particular, a conventional activated sludge (CAS) system as control and a system implementing the OSA process both having a pre-denitrification scheme were considered. Five periods (P1-P5) were studied, during which several operating conditions and configurations were tested. Specifically, the hydraulic retention time (HRT) in the anaerobic reactor of the OSA system (P1 8 h, P2-P3 12 h, P4 8 h, P5 12 h) and the return sludge from the anaerobic to the anoxic (scheme A) (P1-P2) or aerobic (scheme B) mainstream reactors (P3-P5) were investigated. The results highlighted that the excess sludge production in the OSA was lower in all the configurations (12-41%). In more detail, the observed yield (Y obs ) was reduced from 0.50-0.89 gTSS gCOD -1 (control) to 0.22 -0.34 gTSS gCOD -1 in the OSA process. The highest excess sludge reduction (40%) was achieved when the OSA was operated according to scheme B and HRT of 12 h in the anaerobic reactor (P3). Generally, scheme A enabled the establishment of cell lysis and extracellular polymeric substances (EPS) destructuration, leading to a worsening of process performances when high anaerobic HRT (>8 h) was imposed. In contrast, scheme B enabled the establishment of maintenance metabolism in addition to the uncoupling metabolism, while cell lysis and EPS destruction were minimized. This allowed obtaining higher sludge reduction yield without compromising the effluent quality., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Citrus wastewaters (CWWs) are by-products of the citrus fruit transformation process. Currently, more than 700 million of m³ of CWWs per year are produced worldwide. Until nowadays, the management of CWWs is based on a take-make-use-dispose model. Indeed, after being produced within a citrus processing industry, CWWs are subjected to treatment and then discharged into the environment. Now, the European Union is pushing towards a take-make-use-reuse management model, which suggests to provide for the minimization of residual pollutants simultaneously with their exploitation through a biorefinery concept. Indeed, the recovery of energy nutrients and other value-added products held by CWWs may promote environmental sustainability and close the nutrient cycles in line with the circular bio-economy perspective. Unfortunately, knowledge about the benefits and disadvantages of available technologies for the management and valorisation of CWWs are very fragmentary, thus not providing to the scientific community and stakeholders an appropriate approach. Moreover, available studies focus on a specific treatment/valorisation pathway of CWWs and an overall vision is still missing. This review aims to provide an integrated approach for the sustainable management of CWWs to be proposed to company managers and other stakeholders within the legislative boundaries and in line with the circular bio-economy perspective. To this aim, firstly, a concise analysis of citrus wastewater characteristics and the main current regulations on CWWs are reported and discussed. Then, the main technologies with a general comparison of their pros and cons, and alternative pathways for CWWs utilization are presented and discussed. Finally, a focus was paid to the economic feasibility of the solutions proposed to date relating to the recovery of the CWWs for the production of both value-added compounds and agricultural reuse. Based on literature analysis an integrated approach for a sustainable CWWs management is proposed. Such an approach suggests that after chemicals recovery by biorefinery, wastewaters should be directly used for crop irrigation if allowed by regulations or addressed to treatment plant. The latter way should be preferred when CWWs cannot be directly applied to soil due to lack of concomitance between CWWs production and crop needs. In such a way, treated wastewater should be reused after tertiary treatments for crop irrigation, whereas produced sludges should be undergone to dewatering treatment before being reused as organic amendment to improve soil fertility. Finally, this review invite European institutions and each Member State to promote common and specific legislations to overcome the fragmentation of the regulatory framework regarding CWWs reuse., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Fouling is considered one of the main drawbacks of membrane bioreactor (MBR) technology. Among the main fouling agents, extracellular polymeric substances (EPS) are considered one of the most impactful since they cause the decrease of sludge filterability and decline of membrane flux in the long term. The present study investigated a biological strategy to reduce the membrane-fouling tendency in MBR systems. This consisted of seeding the reactor with activated sludge enriched in microorganisms with polyhydroxyalkanoate (PHA) storage ability and by imposing proper operating conditions to drive the carbon toward intracellular (PHA) rather than extracellular (EPS) accumulation. For that purpose, an MBR lab-scale plant was operated for 175 days, divided into four periods (1-4) according to different food to microorganisms' ratios (F/M) (0.80 kg COD kg TSS -1 d -1 (Period 1), 0.13 kg COD kg TSS -1 d -1 (Period 2), 0.28 kg COD kg TSS -1 d -1 (Period 3), and 0.38 kg COD kg TSS -1 d -1 (Period 4)). The application of the feast/famine strategy favored the accumulation of intracellular polymers by bacteria. The increase of the PHA accumulation inside the cells corresponded to the decrease of EPS and an F/M of 0.40-0.50 kg COD kg TSS -1 d -1 was found as optimum to maximize the PHA production, while minimizing EPS. The lowest EPS content in the sludge (18% of total suspended solids) that corresponded to the maximum content of PHA (9.3%) was found in Period 4 and determined significant mitigation of the fouling rate, whose value was close to 0.10 × 10 11 m -1 h -1 . Thus, by imposing proper operating conditions, it was possible to drive the organic matter toward PHA accumulation. Moreover, a lower EPS content corresponded to a decrease in the irreversible fouling mechanism, which would imply a lower frequency of the extraordinary cleaning operations. This study highlighted the possibility of obtaining a double benefit by applying an MBR system in the frame of wastewater valorization: minimizing the fouling tendency of the membrane and recovery precursors of bioplastics from wastewater in line with the circular economy model.

In this study, the presence of microplastics in the sludge of three wastewater treatment plants (WWTPs) was examined. The investigated WWTPs operated based on a conventional activated sludge (CAS) process, with (W1) or without (W2) primary clarification, and a membrane bioreactor process (MBR) (W3). The microplastics (MPs) concentration in the samples of W3 was approximately 81.1 ± 4.2 × 10 3 particles/kg dry sludge, whereas MPs concentrations in W1 and W2 were 46.0 ± 14.8 × 10 3 particles/kg dry sludge and 36.0 ± 5.2 × 10 3 particles/kg dry sludge, respectively. Moreover, MPs mainly consisted of fragments (66-68%) in the CAS plants, whereas the fractions of MPs shapes in the MBR sludge were more evenly distributed, although fiber (47%) was the most abundant fraction. Furthermore, samples from the MBR showed a greater diversity in MPs composition. Indeed, all the main polyesters (i.e., textile fibers and polyethylene terephthalate), polyolefins (i.e., polyethylene and polypropylene) and rubber (i.e., polybutadiene) were observed, whereas only polybutadiene, cellulose acetate and polyester were detected in the CAS plants. These findings confirmed that MPs from wastewater are transferred and concentrated in the waste sludge. This is a critical finding since sludge disposal could become a new pathway for microplastic release into the environment and because MPs might affect the fouling behavior of the membrane.

The aim of this study was to evaluate the effect of the inoculum to substrate ratio (ISR) and the mixture ratio between organic fraction of municipal solid waste (OFMSW) and sewage sludge (SS) on the methane production potential achievable from anaerobic co-digestion (AcoD). Biochemical Methane Potential (BMP) assays at mesophilic temperature were used to determine the best AcoD configuration for maximizing methane yield and production rate, as well as to address possible synergistic effects. The maximum methane yield was observed at ISR of 1 and 60% OFMSW: 40% SS as co-digestion mixture, whereas the highest methane production rate was achieved at ISR of 2 with the same mixture ratio (207 mL/gVS/d). Synergistic effects were highlighted in the mixtures having OFMSW below 60%, determining an increase of approximately 40% in methane production than the OFMSW and SS digestion as a sole substrate. The experimental data demonstrated that co-digestion of OFMSW and SS resulted in an increase in the productivity of methane than anaerobic digestion using the sole substrates, producing higher yields or production rates while depending on the ISR and the mixture ratio.

The integration of one anaerobic reactor in the mainstream (AMSR) of a pre-denitritication-MBR was evaluated with the aim to achieve simultaneous sludge minimization and phosphorous removal. The excess sludge production was reduced by 64% when the AMSR was operated under 8 h of hydraulic retention time (HRT). The highest nutrients removal performances referred to organic carbon (98%), nitrogen (90%) and phosphorous (97%) were obtained under 8 h of HRT. In contrast, prolonged anaerobic-endogenous conditions were found to be detrimental for all nutrients removal performances. Similarly, the lowest membrane fouling tendency (FR = 0.65∙10 11  m -1  d -1 ) was achieved under 8 h of HRT, whereas it significantly increased under higher HRT. The highest polyphosphate accumulating organisms kinetics were achieved under HRT of 8 h, showing very high exogenous P-release (46.67 mgPO 4 -P gVSS -1 h -1 ) and P-uptake rates (48.6 mgPO 4 -P gVSS -1 h -1 ), as well as a not negligible P-release rate under endogenous conditions at low COD/P ratio (≈1)., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

In the present paper, the feasibility of citrus wastewater treatment with aerobic granular sludge sequencing batch reactors (AGSBR) was investigated. Two AGSBRs (named R1 and R2, respectively) were operated for 90 days under different organic loading rates (OLR) and pH in two experimental periods. The OLR ranged approximately between 3.0 kg TCOD m -3 d -1 and 7 kg TCOD m -3 d -1 during Period I, whereas between 7 kg TCOD m -3 d -1 and 15 kg TCOD m -3 d -1 during Period II. pH was maintained at 7.0 and 5.5 in R1 and R2, respectively. The results revealed that under high OLR and unbalanced feast/famine regime (Period I), the development of fast-growing microorganisms (fungi and filamentous bacteria) was favoured in both reactors, resulting in granular sludge instability. An extended famine phase and a proper balancing between feast and famine periods (Period II) were favourable for the development of bacteria with low growth rates (0.05 d -1 ) thus enhancing the granules stability. To the benefit of granular sludge stability and effluent quality, the length of the feast period should not exceed 25% of cycle length. Moreover, under OLR lower than 7 kg TCOD m -3 d -1 the removal efficiency of total chemical oxygen demand (TCOD) was approximately 90% in R1 and R2 and no side effects on the organic carbon removal performance related to the pH were observed. In contrast, at higher OLR a significant decrease in the removal efficiency (from 90% to less than 75%) was observed in R2. Results revealed also that under low pH, hydrolysis of proteins occurred and a decrease in the biological kinetic rates proportionally to the applied OLR was observed., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

Autochthonous halophilic biomass was cultivated in a sequencing batch reactor (SBR) aimed at analyzing the potential use of autochthonous halophilic activated sludge in treating saline industrial wastewater. Despite the high salt concentration (30 g NaCl L -1 ), biological oxygen demand (BOD) and total suspended solids (TSS), removal efficiencies were higher than 90%. More than 95% of the nitrogen was removed via a shortcut nitrification-denitrification process. Both the autotrophic and heterotrophic biomass samples exhibited high biological activity. The use of autochthonous halophilic biomass led to high-quality effluent and helped to manage the issues related to nitrogen removal in saline wastewater treatment., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

This work aims to investigate the stability of aerobic granular sludge in the long term, focusing on the clogging of the granular sludge porosity exerted by the extracellular polymeric substances (EPSs). The effects of different cycle lengths (short and long-term cycle) on the granular sludge stability were investigated. Results obtained outlined that during the short duration cycle, the formation and breakage of the aerobic granules were continuously observed. During this period, the excess of EPS production contributed to the clogging of the granules porosity, causing their breakage in the long run. During the long-duration cycle, the extended famine period entailed a greater EPSs consumption by bacteria, thus limiting the clogging of the porosity, and allowed obtaining stable aerobic granules. Reported results demonstrated that an excess in EPSs content could be detrimental to the stability of aerobic granular sludge in the long-term., (Copyright © 2016 Elsevier Ltd. All rights reserved.)