Search

[Display omitted] • 2D GnP/MoS 2 and 3D (GnP/MoS 2)/MWNT composites are prepared by a facile, robust and ecofriendly method. • Effects of N-doping of GnPs and mass fraction of MWNTs on ORR activity are explored and rationalized. • Best synergistic ORR activity is obtained for N-doped catalyst with 3:1 2D-to-1D ratio. • Catalysts exhibit excellent stability and methanol resistance in alkaline medium. • Promising route to develop bifunctional ORR/OER catalysts. Nanocomposites have garnered attention for their potential as catalysts in electrochemical reactions vital for technologies like fuel cells, water splitting, and metal-air batteries. This work focuses on developing three-dimensional (3D) nanocomposites through aqueous phase exfoliation, non-covalent functionalization of building blocks with surfactants and polymers, and electrostatic interactions in solution leading to the nanocomposites assembly and organization. By combining molybdenum disulfide (MoS 2) layers with graphene nanoplatelets (GnPs) to form a binary 2D composite (MoS 2 /GnP), and subsequently incorporating multiwalled carbon nanotubes (MWNTs) to create ternary 3D composites, we explore their potential as catalysts for the oxygen reduction reaction (ORR) critical in fuel cells. Characterization techniques such as X-ray photoelectron spectroscopy, scanning electron microscopy, and X-ray diffraction elucidate material composition and structure. Our electrochemical studies reveal insights into the kinetics of the reactions and structure–activity relationships. Both the (MoS 2 /GnP)-to-MWNT mass ratio and nitrogen-doping of GnPs (N -GnPs) play a key role on the electrocatalytic ORR performance. Notably, the (MoS 2 / N -GnP)/MWNT material, with a 3:1 mass ratio, exhibits the most effective ORR activity. All catalysts demonstrate good long-term stability and methanol crossover tolerance. This facile fabrication method and observed trends offer avenues for optimizing composite electrocatalysts further. [ABSTRACT FROM AUTHOR]

Polymer electrolyte membrane fuel cells (PEMFCs) have attracted much attention as highly efficient, eco-friendly energy conversion devices. However, carbon-supported Pt (Pt/C) catalysts for PEMFCs still have several problems, such as low long-term stability, to be widely commercialized in fuel cell applications. To address the stability issues of Pt/C such as the dissolution, detachment, and agglomeration of Pt nanoparticles under harsh operating conditions, we design an interesting fabrication process to produce a highly active and durable Pt catalyst by introducing a robust carbon shell on the Pt surface. Furthermore, this approach provides insights into how to regulate the carbon shell layer for fuel cell applications. Through the application of an appropriate amount of H2 gas during heat treatment, the carbon shell pores, which are integral to the structure, can be systematically modulated to facilitate oxygen adsorption for the oxygen reduction reaction. Simultaneously, the carbon shell functions as a protective barrier, preventing catalyst degradation. In this regard, we investigate an in-depth analysis of the effects of critical parameters including H2 content and the flow rate of H2/N2 mixed gas during heat treatment to prepare better catalysts. [ABSTRACT FROM AUTHOR]

Samaria-doped ceria (SDC) overlayers were deposited on Ag cathodes by sputtering. The SDC sputtering time was varied to investigate the properties of the Ag–SDC overlayer cathode-coated fuel cells depending on the thickness of the SDC overlayers. Among the fabricated fuel cells, Ag with a 10-nm-thick SDC overlayer (Ag-SDC10) cathode-coated fuel cell exhibited the highest peak power density of 6.587 mW/cm2 at 450 °C, showing higher performance than a pristine Pt-coated fuel cell. Moreover, electrochemical impedance spectroscopy revealed that the Ag-SDC10 cathode-coated fuel cell significantly mitigated polarization loss originating from enhanced oxygen reduction reaction kinetics compared to the pristine Ag-coated fuel cell. [ABSTRACT FROM AUTHOR]

[Display omitted] Lowering the operating temperatures of solid-oxide fuel cells (SOFCs) is critical, although achieving success in this endeavor has proven challenging. Herein, Bi 0.15 Sr 0.85 Co 0.8 Fe 0.2 O 3−δ (BiSCF) is systematically evaluated as a carbon dioxide (CO 2)-tolerant and highly active cathode for SOFCs. BiSCF, which features Bi3+ with an ionic radius similar to Ba2+, exhibits activity (e.g., 0.062 Ω cm2 at 700 °C) comparable to that of Ba 0.5 Sr 0.5 Co 0.8 Fe 0.2 O 3−δ and PrBaCo 2 O 5+δ , while demonstrating a considerable advantage over Bi-doped cathodes. Moreover, BiSCF exhibits long-term stability over a period of 500 h, and an anode-supported cell with BiSCF achieves a power density of 912 mW cm−2 at 650 °C. The CO 2 -poisoned BiSCF exhibits quick reversibility or slight activation after returning to normal conditions. The exceptional CO 2 tolerance of BiSCF can be attributed to its reduced basicity and high electronegativity, which effectively restrict surface Sr diffusion and hinder subsequent carbonate formation. These findings highlight the substantial potential of BiSCF for SOFCs operating below 700 °C. [ABSTRACT FROM AUTHOR]

Search for a Platinum metal-free catalyst for Proton Exchange Membrane Fuel Cells (PEMFCs) is a concern to scientists as the Pt-catalyzed electrode comprises about 45% of the entire fuel cell stack cost. Due to layered structure, Two-dimensional (2D) MoS2 nanostructured materials have recently drawn attention as effective catalysts for oxygen reduction reaction (ORR). The 1T-phase of MoS2 (1T-MoS2) has higher electronic conductivity than the 2H-phase (2H-MoS2); high surface area 1T-MoS2 can have high electrocatalytic activity towards PEFFCs. Here, we report hydrothermally synthesized 2H-MoS2 and solvothermally synthesized mixed 1T/2H-MoS2 phases as a catalyst for ORR in PEM Fuel Cells. Owing to the high BET-specific surface area, hybrid 1T/2H-MoS2 showed better ORR activity than 2H-MoS2. The limiting current density of the 1T/2H-MoS2 hybrid structure is ‒7.1 mA cm−2 compared to Pt/C (‒8.2 mA cm−2) at 1600 rpm. The Tafel slope values of 2H-MoS2, 1T/2H-MoS2, and Pt/C are 92.7 mV dec−1, 57.5 mV dec−1, and 39.3 mV dec−1, respectively. The electron transferred during ORR are 3.8 and 1.8, respectively, for 1T/2H-MoS2 and 2H-MoS2 (in 0.1 M KOH) ; suggesting less formation of undesirable peroxide formation than 2H-MoS2. The 1T/2H-MoS2 displays better electrochemical durability compared to 2H-MoS2 (after 2000 CV cycles). [ABSTRACT FROM AUTHOR]

The development of precious metal-free (M-N-C) catalysts for the oxygen reduction reaction (ORR) is considered crucial for reducing fuel cell costs. Herein, Co-Zn/NC interconnected frameworks with uniformly dispersed Co nanoparticles and graphitic carbon are designed and successfully synthesized through the in situ growth of zeolitic imidazolate frameworks (ZIF67 and ZIF8) along with biomass nano-microfibrillar cellulose (MFC), followed by pyrolysis. A Co-Zn/NC composite is prepared by combining Co-Zn/NC with a perfluorosulfonic acid polymer. The Co-Zn/NC composite catalyst exhibits excellent ORR catalytic activity (E0 = 0.974 V vs. RHE, E1/2 = 0.858 V vs. RHE) and good long-term durability, with 90% current retention after 10000s, surpassing that of commercial Pt/C in alkaline media. The hierarchical porous structure, coupled with the uniform distribution of Co nanoparticles and nitrogen doping, contributes to superior electrocatalytic performance, while the interconnected frameworks and graphitic carbon ensure good stability. Additionally, the Co-Zn/NC composite demonstrates promising applications in acidic media. This strategy offers significant guidance to develop advanced non-precious metal carbon-based catalysts for highly efficient and stable ORR. [ABSTRACT FROM AUTHOR]

The efficiency and performance of proton exchange membrane fuel cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed metal–nitrogen–carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufacturing cost of the entire system, thereby facilitating the commercialization and widespread application of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bimetallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. This article concludes by detailing the current challenges and future prospects of atomically dispersed Fe-N-C catalysts. [ABSTRACT FROM AUTHOR]

Atomically dispersed Fe-N-C catalysts for the oxygen reduction reaction (ORR) have been synthesized with a template-free method using carbon xerogels (CXG) as a porous matrix. The porosity of the CXGs is easily tunable through slight variations in the synthesis procedure. In this work, CXGs are prepared by formaldehyde and resorcinol polymerization, modifying the pH during the process. Materials with a broad range of porous structures are obtained: from non-porous to micro-/meso-/macroporous materials. The porous properties of CXG have a direct effect on Fe-N-CXG activity against ORR in an acidic medium (0.5 M H2SO4). Macropores and wide mesopores are vital to favor the mass transport of reagents to the active sites available in the micropores, while narrower mesopores can generate additional tortuosity. The role of microporosity is investigated by comparing two Fe-N-C catalysts using the same CXG as the matrix but following a different Fe and N doping procedure. In one case, the carbonization of CXG occurs rapidly and simultaneously with Fe and N doping, whereas in the other case it proceeds slowly, under controlled conditions and before the doping process, resulting in the formation of more micropores and active sites and achieving higher activity in a three-electrode cell and a better durability during fuel cell measurements. This work proves the feasibility of the template-free method using CXG as a carbon matrix for Fe-N-C catalysts, with the novelty of the controlled porous properties of the carbon material and its effect on the catalytic activity of the Fe-N-C catalyst. Moreover, the results obtained highlight the importance of the carbon matrix's porous structure in influencing the activity of Fe-N-C catalysts against ORR. [ABSTRACT FROM AUTHOR]

An oxygen reduction reaction (ORR) is the key half reaction of proton exchange membrane fuel cells (PEMFCs), and is highly dependent on Pt-based nanocrystals as core electrocatalysts. Despite the exceptional ORR activity from adjusting the electronic structures of surface or near-surface atoms, several serious issues, including the corrosion of carbon supports, the preferential leaching of active metal elements, the instability of surface low-coordinated atoms and the sintering/agglomeration of nanocrystals, still exist, challenging the ORR durability of developed Pt-based ORR catalysts. From the point of view of the catalyst structure design, in this review, we summarized the state-of-the-art structural regulation strategies for improving the ORR durability of Pt-based catalysts. The current limitation of Pt-based binary catalysts for ORR electrocatalysis is firstly discussed, and the detailed strategies are further classified into the optimization of supports, metal-doped alloys, core/shell structures, intermetallics and high-entropy alloys, etc. The structure–performance relationship is detailedly explained, especially emphasizing the elimination of the above restrictions. Finally, the existing challenges and future research direction are further presented, aiming at practicing the PEMFC devices of the ultradurable Pt-based catalysts. [ABSTRACT FROM AUTHOR]

Studying the ORR activity of platinum-based electrocatalysts is an urgent task in the development of materials for proton-exchange membrane fuel cells. The catalytic ink composition and the formation technique of a thin layer at the RDE play a significant role in studying ORR activity. The use of a polymer ionomer in the catalytic ink provides viscosity as well as proton conductivity. Nafion is widely used as an ionomer for research both at the RDE and in the MEA. The search for ionomers is a priority task in the development of the MEA components to replace Nafion. The study also considers the possibility of using the LF4-SK polymer as an alternative ionomer. The comparative results on the composition and techniques of applying the catalytic layer using LF4-SK and Nafion ionomers are presented, and the influence of the catalytic ink composition on the electrochemical characteristics of commercial platinum–carbon catalysts and a highly efficient platinum catalyst based on an N-doped carbon support is assessed. [ABSTRACT FROM AUTHOR]

[Display omitted] • A two stage confinement strategy assisted facile synthesis of 5.3 nm highly ordered PtCoZn/NC. • PtCoZn/NC ordering and graphitization are promoted by regulating composition and calcination-time. • High intrinsic activity (2.8 mA cm-2 Pt) and slight E 1/2 loss (9 mV) in ADT were achieved by PtCoZn/NC. • It is evidenced weaker O binding and stronger Pt-Co/Zn bonding enhance activity and durability. • The ionomer-free and anti-sintering feature of carbon-walls also benefit the MEA performance. Intermetallic ordered PtCo is effective for high oxygen reduction reaction (ORR) activity and stability. However, preparing small-sized, highly ordered PtM alloys is still challenging. Herein, we report a controlled two-stage confinement strategy, in which highly ordered PtCoZn/NC nanoparticles of 5.3 nm size were prepared in a scalable process. The contradiction between the high ordering degree with the small particle size as well as the atomic migration with the space confinement was well resolved. An outstanding PEMFC performance was achieved for L1 0 -PtCoZn/NC with a high mass activity (MA) of 1.21 A/mg Pt at 0.9 V iR-free , 80.1 % MA retention after 30 k cycles in H 2 -O 2 operation, and a high mass-specific power density of 8.24 W mg-1 Pt in H 2 -Air operation with a slight loss of cell voltage@0.8 A cm−2 of 28 mV after 30 k cycles. The high performance can be ascribed to the high Pt area exposure, the enhanced Pt-Co coupling, and the prevented agglomeration in the mesoporous carbon wall. Overall, this strategy may contribute to the commercialization of fuel cells. [ABSTRACT FROM AUTHOR]

Currently, the development of nonmetallic oxygen reduction reaction (ORR) catalysts based on heteroatomic-doped carbon materials is receiving increaseing attention in the field of fuel cells. Here, we used enzymolytic lignin (EL), melamine, and thiourea as carbon, nitrogen, and sulfur sources and NH4Cl as an activator to prepare N- and S-codoped lignin-based polyporous carbon (ELC) by one-step pyrolysis. The prepared lignin-derived biocarbon material (ELC-1-900) possessed a high specific surface area (844 m2 g−1), abundant mesoporous structure, and a large pore volume (0.587 cm3 g−1). The XPS results showed that ELC-1-900 was successfully doped with N and S. ELC-1-900 exhibited extremely high activity and stability in alkaline media for the ORR, with a half-wave potential (E1/2 = 0.88 V) and starting potential (Eonset = 0.98 V) superior to those of Pt/C catalysts and most non-noble-metal catalysts reported in recent studies. In addition, ELC-1-900 showed better ORR stability and methanol tolerance in alkaline media than commercial Pt/C catalysts. [ABSTRACT FROM AUTHOR]

The use of platinum-free (Pt) cathode electrocatalysts for oxygen reduction reactions (ORRs) has been significantly studied over the past decade, improving slow reaction mechanisms. For many significant energy conversion and storage technologies, including fuel cells and metal–air batteries, the ORR is a crucial process. These have motivated the development of highly active and long-lasting platinum-free electrocatalysts, which cost less than proton exchange membrane fuel cells (PEMFCs). Researchers have identified a novel, non-precious carbon-based electrocatalyst material as the most effective substitute for platinum (Pt) electrocatalysts. Rich sources, outstanding electrical conductivity, adaptable molecular structures, and environmental compatibility are just a few of its benefits. Additionally, the increased surface area and the simplicity of regulating its structure can significantly improve the electrocatalyst's reactive sites and mass transport. Other benefits include the use of heteroatoms and single or multiple metal atoms, which are capable of acting as extremely effective ORR electrocatalysts. The rapid innovations in non-precious carbon-based nanomaterials in the ORR electrocatalyst field are the main topics of this review. As a result, this review provides an overview of the basic ORR reaction and the mechanism of the active sites in non-precious carbon-based electrocatalysts. Further analysis of the development, performance, and evaluation of these systems is provided in more detail. Furthermore, the significance of doping is highlighted and discussed, which shows how researchers can enhance the properties of electrocatalysts. Finally, this review discusses the existing challenges and expectations for the development of highly efficient and inexpensive electrocatalysts that are linked to crucial technologies in this expanding field. [ABSTRACT FROM AUTHOR]

[Display omitted] Palladium-based nanocatalysts play an important role in catalyzing the cathode oxygen reduction reaction (ORR) for fuel cells working under alkaline conditions, but the performance still needs to be improved to meet the requirements for large-scale applications. Herein, Au@Pd core–shell nanowires have been developed by coating Pd atomic layers on ultrafine gold nanowires and display outstanding electrocatalytic performance towards alkaline ORR. It is found that Pd overlayers with atomic thickness can be coated on 3 nm Au nanowires under CO atmosphere and completely cover the surfaces. The obtained ultrafine Au@Pd nanowires exhibit an electrochemical active area (ECSA) of 68.5 m2/g and a mass activity of 0.91 A/mg (at 0.9 V vs. RHE), which is around 3.1 and 15.2 times higher than that of commercial Pd/C. The activity loss of the ultrafine Au@Pd nanowire after 10,000 cycles of accelerated degradation tests is only ∼20 %, demonstrating its much better stability compared to commercial Pd/C. Further characterizations combined with density functional theory (DFT) calculations demonstrate that the electronic interactions between Pd atomic layers and underlying Au can increase the electronic density of Pd and promote the efficient activation of oxygen, thus leading to the improved ORR performance. [ABSTRACT FROM AUTHOR]

In light of the depletion of conventional energy sources, it is imperative to conduct research and development on sustainable alternative energy sources. Currently, electrochemical energy storage and conversion technologies such as fuel cells and metal-air batteries rely heavily on precious metal catalysts like Pt/C and IrO2, which hinders their sustainable commercial development. Therefore, researchers have devoted significant attention to non-precious metal-based catalysts that exhibit high efficiency, low cost, and environmental friendliness. Among them, perovskite oxides possess low-cost and abundant reserves, as well as flexible oxidation valence states and a multi-defect surface. Due to their advantageous structural characteristics and easily adjustable physicochemical properties, extensive research has been conducted on perovskite-based oxides. However, these materials also exhibit drawbacks such as poor intrinsic activity, limited specific surface area, and relatively low apparent catalytic activity compared to precious metal catalysts. To address these limitations, current research is focused on enhancing the physicochemical properties of perovskite-based oxides. The catalytic activity and stability of perovskite-based oxides in Oxygen Reduction Reaction/Oxygen Evolution Reaction (ORR/OER) can be enhanced using crystallographic structure tuning, cationic regulation, anionic regulation, and nano-processing. Furthermore, extensive research has been conducted on the composite processing of perovskite oxides with other materials, which has demonstrated enhanced catalytic performance. Based on these different ORR/OER modification strategies, the future challenges of perovskite-based bifunctional oxygen electrocatalysts are discussed alongside their development prospects. [ABSTRACT FROM AUTHOR]

[Display omitted] • A plasma-assisted approach is developed to improve the SD and site utilization of Fe N C catalyst. • The plasma-assisted approach can give a 2.81-fold SD improvement and 1.98-fold higher site utilization, simultaneously. • The carbon defects near the Fe-N 4 sites can regulate the electronic structure and promoted the intrinsic activity of Fe-N 4 sites. • The hierarchical pore structure increased the abundance of edge sites and enhance the mass transport performance of Fe N C. Enhancing the density and utilization of FeN 4 sites can serve as a viable approach to enhance the catalytic efficacy of iron nitrogen carbon (Fe N C) catalysts for oxygen reduction reaction (ORR). Herein, we present a plasma-assisted method for enhancing the porosity of nitrogen-doped carbon. Our findings indicate that the ideal ratio of mesopore to micropore area is 0.463. This ratio not only promotes the diffusion of Fe3+ but also creates additional active sites for Fe3+ loading, leading to an increase in the number of available FeN 4 sites in Fe N C electrocatalysts during pyrolysis. The density (76.5 μmol g−1) and utilization (21.08 %) of d -FeNC-30 are significantly higher than those of FeNC without plasma treatment, with a 2.8-fold and 2-fold increase, respectively. Remarkably, it displays outstanding performance, evidenced by a half-wave potential of 0.835 V (vs. RHE) in a 0.1 M HClO 4 solution and a power density of 0.860 W cm−2 in proton exchange membrane fuel cells (PEMFCs). The developed plasma-assisted approach for improving the site density (SD) and utilization of FeN 4 provides a new perspective for high-performance ORR Fe N C catalysts. [ABSTRACT FROM AUTHOR]

Solid oxide fuel cells (SOFCs) represent a breed of eco-friendly, weather-independent, decentralized power generation technologies, distinguished for their broad fuel versatility and superior electricity generation efficiency. At present, SOFCs are impeded by a lack of highly efficient oxygen reduction catalysts, a factor that significantly constrains their performance. The double perovskites LnBaCo2O5+δ (Ln = Lanthanide), renowned for their accelerated oxygen exchange and conductivity features, are widely acclaimed as a promising category of cathode catalysts for SOFCs. This manuscript offers a novel perspective on the physicochemical attributes of LnBaCo2O5+δ accumulated over the past two decades and delineates the latest advancements in fine-tuning the composition and nanostructure for SOFC applications. It highlights surface chemistry under operational conditions and microstructure as emerging research focal points towards achieving high-performance LnBaCo2O5+δ catalysts. This review offers a comprehensive insight into the latest advancements in utilizing LnBaCo2O5+δ in the field of SOFCs, presenting a clear roadmap for future developmental trajectories. Furthermore, it provides valuable insights for the application of double perovskite materials in domains such as water electrolysis, CO2 electrolysis, chemical sensors, and metal–air batteries. [ABSTRACT FROM AUTHOR]

We propose a new design for electrocatalysts consisting of two electrocatalysts (platinum and iron oxide) that are deposited on the surfaces of an oxidized graphene substrate. This design is based on a simple structure where the catalysts were deposited separately on both sides of oxidized graphene substrate; while the iron oxide precipitated out of the etching solution on the bottom-side, the surface of the oxidized graphene substrate was decorated with platinum using the atomic layer deposition technique. The Fe2O3-decorated CVD-graphene composite exhibited better hydrogen electrooxidation performance (area-normalized electrode resistance (ANR) of ~600 Ω·cm−2) and superior stability in comparison with bare-graphene samples (ANR of ~5800 Ω·cm−2). Electrochemical impedance measurements in humidified hydrogen at 240 °C for (Fe2O3|Graphene|Platinum) electrodes show ANR of ~0.06 Ω·cm−2 for a platinum loading of ~60 µgPt·cm−2 and Fe2O3 loading of ~2.4 µgFe·cm−2, resulting in an outstanding mass normalized activity of almost 280 S·mgPt−1, exceeding even state-of-the-art electrodes. This ANR value is ~30% lower than the charge transfer resistance of the same electrode composition in the absence of Fe2O3 nanoparticles. Detailed study of the Fe2O3 electrocatalytic properties reveals a significant improvement in the electrode's activity and performance stability with the addition of iron ions to the platinum-decorated oxidized graphene cathodes, indicating that these hybrid (Fe2O3|Graphene|Platinum) materials may serve as highly efficient catalysts for solid acid fuel cells and beyond. [ABSTRACT FROM AUTHOR]

With the increasing demand for green and efficient energy storage devices， advanced technologies for clean energy conversion have attracted close attention from researchers. Fuel cells with environmental friendliness and high energy conversion efficiency are promising alternatives to traditional energy sources. However， Pt catalysts with high commercialization degrees in the industrial catalysis field have some problems， such as high cost， poor stability and weak anti-toxicity ability， which limits the further development of fuel cells. The development of non-Pt oxygen reduction reaction （ORR） catalysts with abundant reserves， low cost and excellent performance is an effective way to improve the efficiency of fuel cells. In this paper， based on the research results at home and abroad in recent years， various types of non-Pt system ORR catalysts， including non-precious metal and non-metal catalysts， are systematically introduced. The advantages， disadvantages and modification strategies of various catalysts are summarized， and challenges and prospects for the development of ORR electrocatalysts are put forward. [ABSTRACT FROM AUTHOR]

As a key role in hindering the large-scale application of fuel cells, oxygen reduction reaction has always been a hot issue and nodus. Aiming to explore state-of-art electrocatalysts, this paper reviews the latest development of nonmetallic catalysts in oxygen reduction reactions, including single atoms doped with carbon materials such as N, B, P or S and multi-doped carbon materials. Afterward, the remaining challenges and research directions of carbon-based nonmetallic catalysts are prospected. [ABSTRACT FROM AUTHOR]

High-porosity, crystalline, and surface-area-rich metal–organic frameworks (MOFs) may be employed in electrochemical energy applications for active catalysis. MOFs have recently been modified using secondary building blocks, open metal sites with large pore diameters, and functional ligands for electronic conductivity. They have the potential for excellent performance in fuel cell applications, and they have several possibilities to enhance the fundamental characteristics of mass and electron transportation. MOFs may be combined with other materials, such as solitary metal nanoparticles and carbon and nitrogen composites, to increase their catalytic efficacy, especially in oxygen reduction reaction (ORR). As a result, this study focuses on MOF derivatives for ORR applications, including porous carbon MOF, single metal MOF-derived composites, metal oxides, and metal phosphides. An efficient MOF electrocatalyst platform for ORR applications is presented, along with its prospects. These initiatives promote promising MOF electrocatalysts for enhancing fuel cell efficiency and pique curiosity for possible growth in subsequent research. [ABSTRACT FROM AUTHOR]

Ternary PtZrNi NRs have excellent electrocatalytic activity in cathode and cathode reactions of fuel cells. [Display omitted] Pt-based alloys with precise structure and composition design have been considered to be effective and robust novel electrocatalysts for fuel cells. Whereas, the sluggish kinetics of oxygen reduction reaction (ORR) and low intrinsic activity of Pt limited their real application on a large scale. Herein, a novel ternary PtZrNi nanorods (PtZrNi NRs) was synthesized via a facile wet-chemical method to achieve high electrocatalytic performance for both ORR and alcohol oxidation reaction owing to the synergism of chosen three elements and prominent one-dimensional morphology. Specifically, the PtZrNi NRs show enhanced mass and specific activities of 0.755 A mg Pt -1 and of 0.97 mA/cm2 at 0.9 V RHE towards ORR in acidic media, which are 4.7 and 4.4 times of those of commercial Pt/C, respectively. Additionally, in alkaline media, the PtZrNi NRs also exhibit superior ORR mass and specific activities of 3.216 A mg Pt -1and 4.13 mA/cm2, enhanced by 34.6 and 31.3 times compared with those of commercial Pt/C, respectively. The PtZrNi NRs retain the nanorod shape well without agglomeration after an accelerated durability test (20000 cycles). This work may offer a new perspective for engineering high-performance Pt-based electrocatalysts for commercial fuel cells. [ABSTRACT FROM AUTHOR]

A novel methodology for promoting the topological carbon defects and B/N doping amounts of B/ N -enriched porous Co@BN-PCFs catalysts, which discloses a new direction for further boosting ORR catalytic efficiencies and stabilities of Co N C catalysts in both acids and bases. [Display omitted] • Carboxyl induced abundant mesopores and ultrahigh carbon topological defects in Co@BN-PCNFs. • Ultrahigh B and N doping amounts of 5.87 and 5.91 at.% with 8.70 at.% of B/N based electrocatalytic active centers. • The ORR E onset and E 1/2 values of Co@BN-PCNFs-900 are ∼ 64 and ∼ 63 mV more positive than 20 wt% Pt/C in 0.1 M KOH. • The ORR E onset and E 1/2 values of Co@BN-PCNFs-900 just ∼ 11 and ∼ 7 mV more negative than 20 wt% Pt/C in 0.1 M H 2 SO 4. • The comparatively stable topological edges, BC 3 and partial N C/Co N C induced excellent stability toward ORR. Transition metal-nitrogen-carbon (M N C) type catalysts have been considered a promising alternative to noble metals for oxygen reduction reaction (ORR) electrocatalysis. Nevertheless, poor stabilities of M N C catalysts in acidic solutions limit their commercialization. In this study, we design and synthesize novel three-dimensional (3D) cobalt (Co) nanoparticles encapsulated in ultrahigh content of boron (B) and nitrogen (N) -doped hierarchically porous carbon nanofibers (denoted as Co@BN-PCNFs) by carbonizing the 3D acetic acid/cobalt nitrate/4-hydroxybenzeneboronic acid/polyvinylpyrrolidone precursor networks woven using electrospinning method under a nitrogen atmosphere. The optimal Co@BN-PCNFs-900 catalyst has abundant micro/mesopores and numerous topological defects and exhibits the largest surface area. Under the synergistic effect of oxygen-containing acetic acid molecules and the electrospinning technology, 5.87 at.% of B and 5.91 at.% of N atoms were doped into carbon nanofibers. Specifically, B/N electrocatalytic active centers (including BC 3 , pyridinic-N/Co N C, pyrrolic-N, and graphitic-N) of approximately 8.70 at.% were successfully introduced into the skeletons of Co@BN-PCNFs-900. In 0.1 M KOH, the ORR onset potential (E onset) and half-wave potential (E 1/2) of Co@BN-PCNFs-900 were ∼ 64 and ∼ 63 mV, respectively, more positive than those of 20 wt% Pt/C. Additionally, in 0.5 M H 2 SO 4 , the ORR E onset and E 1/2 values of Co@BN-PCNFs-900 were only ∼ 11 and ∼ 7 mV, respectively, more negative than those of 20 wt% Pt/C. As the 3D hierarchically porous architectures, topological carbon edges, BC 3 , and partial N C/Co N C are relatively stable, the Co@BN-PCNFs-900 exhibits excellent stability toward ORR catalysis in both acidic and basic media. These favorable properties of Co@BN-PCNFs-900 nanofibers make them the best non-noble metal-based carbonaceous electrocatalysts for ORR in acidic electrolytes. [ABSTRACT FROM AUTHOR]

Transition metal and heteroatom co-doped carbon nanomaterials (TM-H-C) are considered to be the most promising candidates to replace the expensive platinum-based catalysts for oxygen reduction reactions (ORR). Herein, we report a semi-closed molten salt-assisted one-step strategy for fabricating N-P-Fe-tridoped porous carbon nanotube (CNT) catalysts by using the evaporation of ZnCl2 and the catalysis of iron ions to control the heteroatoms doping process and CNT formation. The resultant densely packed porous CNT structure imparts final catalysts with an enhanced mass transfer ability for electron and ORR-involved species, ensuring a high performance in catalyzing the ORR. Significantly, the optimal catalysts show a half-wave potential of 0.89 V (vs. RHE), which is better than commercial platinum-based catalysts and most reported TM-H-C ORR catalysts. Impressively, when applied to a primary inc-oxygen (Zn–O2) battery, the synthesized catalyst comprehensively outperforms the state-of-the-art platinum-based catalyst in both its maximum power density and specific capacity. [ABSTRACT FROM AUTHOR]

Graphene is a well-known two-dimensional material with a large surface area and is used for numerous applications in a variety of fields. Metal-free carbon materials such as graphene-based materials are widely used as an electrocatalyst for oxygen reduction reactions (ORRs). Recently, more attention has been paid to developing metal-free graphenes doped with heteroatoms such as N, S, and P as efficient electrocatalysts for ORR. In contrast, we found our prepared graphene from graphene oxide (GO) by the pyrolysis method under a nitrogen atmosphere at 900 °C has shown better ORR activity in aqueous 0.1 M potassium hydroxide solution electrolyte as compared with the electrocatalytic activity of pristine GO. At first, we prepared various graphene by pyrolysis of 50 mg and 100 mg of GO in one to three alumina boats and pyrolyzed the samples under a N2 atmosphere at 900 °C. The prepared samples are named G50-1B to 3B and G100-1B and G100-2B. The prepared GO and graphenes were also analyzed under various characterization techniques to confirm their morphology and structural integrity. The obtained results suggest that the ORR electrocatalytic activity of graphene may differ based on the pyrolysis conditions. We found that G100-1B (Eonset, E1/2, JL, and n values of 0.843, 0.774, 4.558, and 3.76) and G100-2B (Eonset, E1/2, and JL values of 0.837, 0.737, 4.544, and 3.41) displayed better electrocatalytic ORR activity, as did Pt/C electrode (Eonset, E1/2, and JL values of 0.965, 0.864, 5.222, and 3.71, respectively). These results display the wide use of the prepared graphene for ORR and also can be used for fuel cell and metal–air battery applications. [ABSTRACT FROM AUTHOR]

Platinum group metal (PGM)-free oxygen reduction reaction (ORR) catalysts are of utmost importance for the rapid development of anion-exchange membrane fuel cell (AEMFC) technology. In this work, we demonstrate the improved ORR performance and stability of Co and Fe oxide-decorated/N-doped reduced graphene oxide (CoOx-Fe3O4/N-rGO) prepared via a hydrothermal method at the low temperature of 150 °C. The catalysts were characterized thoroughly using transmission electron microscopy, high-angle annular dark field-scanning electron microscopy, X-ray diffraction, N2 physisorption, Raman spectroscopy, and X-ray photoelectron spectroscopy to obtain information about morphology, elemental distribution, phases, porosity, defects, and surface elemental compositions. Significant ORR activity improvement (130 mV@-1.5 mA cm−2) was achieved with this catalyst compared to the pristine graphene oxide, and the ORR limiting current was even 12%@0.5 V higher than the commercial Pt/C. The enhanced ORR activity of CoOx-Fe3O4/N-rGO was attributed to the uniform dispersion of Co, Fe, and N on reduced graphene oxide (rGO) sheets. Furthermore, ORR accelerated stress tests revealed excellent durability, suggesting that this material could be a promising and durable catalyst. With a cathode layer of the CoOx-Fe3O4/N-rGO catalyst, we achieved a peak power density of 676 mW cm−2 in an operando H2-O2 AEMFC. To the best of our knowledge, this is the highest reported power density per cathode catalyst mass in a reported PGM-free cathode catalyst. Finally, we quantified the various cell polarization losses as a function of cathode catalyst loadings to obtain insights for future work with AEMFCs based on this catalyst. The improvement in the AEMFC performance using CoOx-Fe3O4/N-rGO as a cathode catalyst can be attributed to the synergistic effects of (i) the high turnover frequency of the transition metals (Co and Fe) for ORR and (ii) the enhancement provided by N doping to the metal distribution and stability. [ABSTRACT FROM AUTHOR]

The high cost and poor reliability of cathodic electrocatalysts for the oxygen reduction reaction (ORR), which requires significant amounts of expensive and scarce platinum, obstructs the broad applications of proton exchange membrane fuel cells (PEMFCs). The principles of ORR and the reasons for the poor stability of Pt-based catalysts are reviewed. Moreover, this paper discusses and categorizes the strategies for enhancing the stability of Pt-based catalysts in fuel cells. More importantly, it highlights the recent progress of Pt-based stability toward ORR, including surface-doping, intermetallic structures, 1D/2D structures, rational design of support, etc. Finally, for atomic-level in-depth information on ORR catalysts in fuel cells, potential perspectives are suggested, such as large-scale preparation, advanced interpretation techniques, and advanced simulation. This review aims to provide valuable insights into the fundamental science and technical engineering for practical Pt-based ORR electrocatalysts in fuel cells. [ABSTRACT FROM AUTHOR]

Coordination environment engineering is developed to synthesize Fe SA /NSC catalysts with the tailored N, S co-coordinated Fe atomic site. [Display omitted] • The Fe-N 3 S active site with the optimized electronic structure is constructed. • S doping promotes the OH* desorption, thus leading to enhanced kinetics process. • The catalyst displays impressive ORR activity in both alkaline and acidic mediums. • The catalyst exhibits excellent performance in Zn-air batteries and fuel cells. Atomically dispersed iron–nitrogen-carbon (FesbndNsbndC) materials have been considered ideal catalysts for the oxygen reduction. Unfortunately, designing and adjusting the electronic structure of single-atom Fe sites to boost the kinetics and activity still faces grand challenges. In this work, the coordination environment engineering is developed to synthesize the Fe SA /NSC catalyst with the tailored N, S co-coordinated Fe atomic site (Fe-N 3 S site). The structural characterizations and theoretical calculations demonstrate that the incorporation of sulfur can optimize the charge distribution of Fe atoms to weaken the adsorption of OH* and facilitate the desorption of OH*, thus leading to enhanced kinetics process and intrinsic activity. As a result, the S-modified Fe SA /NSC exhibits outstanding catalytic activity with the half-wave potentials (E 1/2) of 0.915 V and 0.797 V, as well as good stability, in alkaline and acidic electrolytes, respectively. Impressively, the excellent performance of Fe SA /NSC is further confirmed in Zn-air batteries (ZABs) and fuel cells, with high peak power densities (146 mW cm−2 and 0.259 W cm−2). [ABSTRACT FROM AUTHOR]

Advancements in inexpensive, efficient, and durable oxygen reduction catalysts is important for maintaining the sustainable development of fuel cells. Although doping carbon materials with transition metals or heteroatomic doping is inexpensive and enhances the electrocatalytic performance of the catalyst, because the charge distribution on its surface is adjusted, the development of a simple method for the synthesis of doped carbon materials remains challenging. Here, a non-precious-metal tris (Fe/N/F)-doped particulate porous carbon material (21P2-Fe1-850) was synthesized by employing a one-step process, using 2-methylimidazole, polytetrafluoroethylene, and FeCl3 as raw materials. The synthesized catalyst exhibited a good oxygen reduction reaction performance with a half-wave potential of 0.85 V in an alkaline medium (compared with 0.84 V of commercial Pt/C). Moreover, it had better stability and methanol resistance than Pt/C. This was mainly attributed to the effect of the tris (Fe/N/F)-doped carbon material on the morphology and chemical composition of the catalyst, thereby enhancing the catalyst's oxygen reduction reaction properties. This work provides a versatile method for the gentle and rapid synthesis of highly electronegative heteroatoms and transition metal co-doped carbon materials. [ABSTRACT FROM AUTHOR]

Sluggish oxygen reduction reaction (ORR) of electrodes is one of the main challenges in fuel cell systems. This study explored the kinetics of the ORR reaction mechanism, which enables us to understand clearly the electrochemical activity of the electrode. In this research, electrocatalysts were synthesized from platinum (Pt) catalyst with multi-walled carbon nanotubes (MWCNTs) coated by three polymers (polybenzimidazole (PBI), sulfonated tetrafluoroethylene (Nafion), and polytetrafluoroethylene (PTFE)) as the supporting materials by the polyol method while hexachloroplatinic acid (H2PtCl6) was used as a catalyst precursor. The oxygen reduction current of the synthesized electrocatalysts increased that endorsed by linear sweep voltammetry (LSV) curves while increasing the rotation rates of the disk electrode. Additionally, MWCNT-PBI-Pt was attributed to the maximum oxygen reduction current densities at −1.45 mA/cm2 while the minimum oxygen reduction current densities of MWCNT-Pt were obtained at −0.96 mAcm2. However, the ring current densities increased steadily from potential 0.6 V to 0.0 V due to their encounter with the hydrogen peroxide species generated by the oxygen reduction reactions. The kinetic limiting current densities (JK) increased gradually with the applied potential from 1.0 V to 0.0 V. It recommends that the ORR consists of a single step that refers to the first-order reaction. In addition, modified MWCNT-supported Pt electrocatalysts exhibited high electrochemically active surface areas (ECSA) at 24.31 m2/g of MWCNT-PBI-Pt, 22.48 m2/g of MWCNT-Nafion-Pt, and 20.85 m2/g of MWCNT-PTFE-Pt, compared to pristine MWCNT-Pt (17.66 m2/g). Therefore, it can be concluded that the additional ionomer phase conducting the ionic species to oxygen reduction in the catalyst layer could be favorable for the ORR reaction. [ABSTRACT FROM AUTHOR]

A porous nano-metal oxide composite consisting of zirconium oxide and vanadium oxide (ZrVNPs) was prepared using precipitation hydrothermal technique, followed by microwave sintering process in order to enhance the catalytic activity toward oxygen reduction reaction (ORR) which is a key reaction in the development of low-temperature fuel cell technology. Microwave sintering process conditions were optimized using response surface methodology models (RSM) and the optimized produced material was called ZrV-T. The physiochemical and electrochemical activities of the fabricated materials were investigated and the results elucidated that, the catalytic efficiency of prepared samples is influenced by morphology, lattice structure, and porosity, as well as metal–support interactions and interfacial structural changes that affect oxygen molecules adsorption and activation. The thermally treated composite (ZrV-T) exhibits higher oxygen reduction performance than the non-sintered material (ZrVNPs). Both materials have different half-wave potentials (E1/2 = −0.36 V) and (E1/2 = −0.29 V) for ZrVNPs and ZrV-T respectively. In addition, ZrV-T has a higher stability than the Pt/C catalyst in 0.1 M KOH solution by 4% after 120 min. Using ZrV-T is likely to reduce costs in FCs and promote the use of electrochemical energy devices and it may also be beneficial in other systems that promote catalytic activity. [ABSTRACT FROM AUTHOR]

The oxygen reduction reaction (ORR) is an important challenge in the development and large-scale distribution of energy conversion devices, especially low-temperature proton exchange membrane (PEM) fuel cells. In order to speed up the ORR kinetics and improve fuel cell performance, iron-doped calcium titanate (CTFO) is proposed as a cocatalyst. Fundamental physical and chemical characterizations by means of X-ray diffraction, infrared spectroscopy, and morphological and thermal analyses for the understanding of the functional features of the proposed materials were carried out. Composite catalysts containing different amounts of CTFO additive with respect to platinum (i.e., Pt:CTFO 1:0.5 and 1:1 wt:wt) were studied using a rotating disk electrode (RDE). Fuel cell tests were performed at 80 °C under 30% and 80% relative humidity. The best Pt:CTFO composite catalyst was compared to a bare Pt/C and a Pt/C:CaTiO3−δ 1:1 catalyst, revealing superior performances of the latter at high relative humidity fuel cell operation, as a combined result of an optimized electrolyte-electrode interface and improved ORR kinetics due to the inorganic additive. [ABSTRACT FROM AUTHOR]

Highlights: A comprehensive discussion of monitoring the structure evolutions of catalysts during ORR via multiple in-situ techniques to identify the active sites is presented. The extensive applications of in-situ techniques in elucidating the oxygen reduction reaction (ORR) mechanisms/pathways are reviewed. The challenges and recommendations of current in-situ techniques for monitoring the various dynamic evolutions in ORR are pointed out. Electrocatalytic oxygen reduction reaction (ORR) is one of the most important reactions in electrochemical energy technologies such as fuel cells and metal–O2/air batteries, etc. However, the essential catalysts to overcome its slow reaction kinetic always undergo a complex dynamic evolution in the actual catalytic process, and the concomitant intermediates and catalytic products also occur continuous conversion and reconstruction. This makes them difficult to be accurately captured, making the identification of ORR active sites and the elucidation of ORR mechanisms difficult. Thus, it is necessary to use extensive in-situ characterization techniques to proceed the real-time monitoring of the catalyst structure and the evolution state of intermediates and products during ORR. This work reviews the major advances in the use of various in-situ techniques to characterize the catalytic processes of various catalysts. Specifically, the catalyst structure evolutions revealed directly by in-situ techniques are systematically summarized, such as phase, valence, electronic transfer, coordination, and spin states varies. In-situ revelation of intermediate adsorption/desorption behavior, and the real-time monitoring of the product nucleation, growth, and reconstruction evolution are equally emphasized in the discussion. Other interference factors, as well as in-situ signal assignment with the aid of theoretical calculations, are also covered. Finally, some major challenges and prospects of in-situ techniques for future catalysts research in the ORR process are proposed. [ABSTRACT FROM AUTHOR]

Exploring low‐cost and high‐efficient electrocatalyst is an exigent task in developing novel sustainable energy conversion systems, such as fuel cells and electrocatalytic fuel generations. 2D materials, specifically 2D superlattice materials focused here, featured highly accessible active areas, high density of active sites, and high compatibility with property‐complementary materials to form heterostructures with desired synergetic effects, have demonstrated to be promising electrocatalysts for boosting the performance of sustainable energy conversion and storage devices. Nevertheless, the reaction kinetics, and in particular, the functional mechanisms of the 2D superlattice‐based catalysts yet remain ambiguous. In this review, based on the recent progress of 2D superlattice materials in electrocatalysis applications, the rational design and fabrication of 2D superlattices are first summarized and the application of 2D superlattices in electrocatalysis is then specifically discussed. Finally, perspectives on the current challenges and the strategies for the future design of 2D superlattice materials are outlined. This review attempts to establish an intrinsic correlation between the 2D superlattice heterostructures and the catalytic properties, so as to provide some insights into developing high‐performance electrocatalysts for next‐generation sustainable energy conversion and storage. [ABSTRACT FROM AUTHOR]

[Display omitted] • Mass production of high activity and durability of Pt/C catalysts with microwave pipeline technology. • Retention rate of ORR catalytic activity of Pt 50 /CB acid -1200 catalyst reaches 82% after 30,000 cycles attenuation. • Power density of cell performance can reach 1.4 W-cm−2 and Pt content can reach 0.286 g Pt -kW−1. Traditional synthesis methodologies for fuel cell catalyst production involve long reactions and uncontrollable reaction processes. Synthesis methods for the production of catalysts typically have difficulties to achieve catalysts materials with consistency, high activity, and durability. In this study, a fast, simple, and suitable continuous pipeline microwave method for catalyst mass production was developed, with the carbon carrier being treated at different temperatures simultaneously. The method herein developed resulted in carbon-supported platinum (Pt) catalysts with high activity and high durability. In addition, the half-wave potential of the catalyst exceeded 0.9 V, the electrochemical active surface area reached 85.7 m2-g Pt −1, and the mass specific activity reached 171.1 mA-mg−1. Remarkably, after 30,000 cycles of Pt attenuation tests and 30,000 cycles of carbon carrier attenuation tests, the retention rate of the annealed carbon carrier catalyst reached 80 %. As a membrane electrode, the catalyst generated a single cell maximum power density of 1.4 W-cm−2, and the Pt content reached 0.286 g Pt -kW−1. The work provides an effective and practical method for the mass production of high-performance and high-durability catalysts, which guiding significance for mass production of catalysts. [ABSTRACT FROM AUTHOR]

[Display omitted] • Mass production of high activity and durability of Pt/C catalysts with microwave pipeline technology. • Retention rate of ORR catalytic activity of Pt 50 /CB acid -1200 catalyst reaches 82% after 30,000 cycles attenuation. • Power density of cell performance can reach 1.4 W-cm−2 and Pt content can reach 0.286 g Pt -kW−1. Traditional synthesis methodologies for fuel cell catalyst production involve long reactions and uncontrollable reaction processes. Synthesis methods for the production of catalysts typically have difficulties to achieve catalysts materials with consistency, high activity, and durability. In this study, a fast, simple, and suitable continuous pipeline microwave method for catalyst mass production was developed, with the carbon carrier being treated at different temperatures simultaneously. The method herein developed resulted in carbon-supported platinum (Pt) catalysts with high activity and high durability. In addition, the half-wave potential of the catalyst exceeded 0.9 V, the electrochemical active surface area reached 85.7 m2-g Pt −1, and the mass specific activity reached 171.1 mA-mg−1. Remarkably, after 30,000 cycles of Pt attenuation tests and 30,000 cycles of carbon carrier attenuation tests, the retention rate of the annealed carbon carrier catalyst reached 80 %. As a membrane electrode, the catalyst generated a single cell maximum power density of 1.4 W-cm−2, and the Pt content reached 0.286 g Pt -kW−1. The work provides an effective and practical method for the mass production of high-performance and high-durability catalysts, which guiding significance for mass production of catalysts. [ABSTRACT FROM AUTHOR]

Polyoxometalates (POMs) are polyatomic ions with closed three-dimensional frameworks. Their unique structure contains a large number of redox active sites, making them promising electrocatalysts for electrochemical energy conversion and storage applications. Thus, this paper presents an overview of the use of POMs as electrocatalysts for electrochemical energy conversion and storage devices, such as batteries, supercapacitors, fuel cells, or water electrolyzers. A discussion of the viability of these materials as alternatives to noble metal-based electrocatalysts is made. The current status of these materials to respond to the challenges of converting modern energy systems into more sustainable ones is also envisaged. [ABSTRACT FROM AUTHOR]

[Display omitted] • We synthesized Au@PtNiAu concave octahedral core-shell nanocatalysts (Au@PtNiAu-COCS). • The mass activity of this catalyst is 11.22 times in ORR and 4.56 times in MOR than commercial Pt/C. • It exhibits a superior power density under fuel cell operation and better performance. • Its half-wave potential displacement after 30 k cycles is only 12 mV. • It retained the 78.8% of MA after 30 k cycles in ORR and lower CO oxidation overpotential in MOR. Despite the remarkable research efforts, the lack of ideal activity and state-of-the-art electrocatalysts remains a substantial challenge for the global application of fuel cell technology. Herein, is reported the synthesis of Au@PtNiAu concave octahedral core-shell nanocatalysts (Au@PtNiAu-COCS) via solvothermal synthesis modification and optimization approach. The special structure generating a large number of step atoms, enhancing the oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR) activity and stability. The superior ORR mass activity of the Au@PtNiAu-COCS is 11.22 times than the exhibited of Pt/C initially by Pt loading, and 5.11 times by Pt + Au loading. After 30 k cycles the mass activity remains 78.8% (8.83 times the initial Pt/C activity) and the half-wave potential only shifts 12 mV. Au@PtNiAu-COCS has superior half-cell activity and gives ideal membrane electrode assemblies. Furthermore, for MOR the Au@PtNiAu-COCS show enhanced anti-toxic (tolerant) ability in CO. This work provides a new strategy to develop core-shell structure nanomaterials for electrocatalysis. [ABSTRACT FROM AUTHOR]

A number of nickel complexes of sodium pectate with varied Ni2+ content have been synthesized and characterized. The presence of the proton conductivity, the possibility of the formation of a dense spatial network of transition metals in these coordination biopolymers, and the immobilization of transition ions in the catalytic sites of this class of compounds make them promising for proton-exchange membrane fuel cells. It has been established that the catalytic system composed of a coordination biopolymer with 20% substitution of sodium ions for divalent nickel ions, Ni (20%)-NaPG, is the leading catalyst in the series of 5, 15, 20, 25, 35% substituted pectates. Among the possible reasons for the improvement in performance the larger specific surface area of this sample compared to the other studied materials and the narrowest distribution of the vertical size of metal arrays were registered. The highest activity during CV and proximity to four-electron transfer during the catalytic cycle have also been observed for this compound. [ABSTRACT FROM AUTHOR]

Oxygen reduction reaction (ORR), an essential reaction in metal–air batteries and fuel cells, still faces many challenges, such as exploiting cost-effective nonprecious metal electrocatalysts and identifying their surface catalytic sites. Here we introduce bulk defects, Frank partial dislocations (FPDs), into metallic cobalt to construct a highly active and stable catalyst and demonstrate an atomic-level insight into its surface terminal catalysis. Through thermally dealloying bimetallic carbide (Co3ZnC), FPDs were in situ generated in the final dealloyed metallic cobalt. Both theoretical calculations and atomic characterizations uncovered that FPD-driven surface terminations create a distinctive type of surface catalytic site that combines concave geometry and compressive strain, and this two-in-one site intensively weakens oxygen binding. When being evaluated for the ORR, the catalyst exhibits onset and half-wave potentials of 1.02 and 0.90 V (versus the reversible hydrogen electrode), respectively, and negligible activity decay after 30,000 cycles. Furthermore, zinc–air batteries and H2–O2/air fuel cells built with this catalyst also achieve remarkable performance, making it a promising alternative to state-of-the-art Pt-based catalysts. Our findings pave the way for the use of bulk defects to upgrade the catalytic properties of nonprecious electrocatalysts. [ABSTRACT FROM AUTHOR]

The development of non−Pt or carbon−based catalysts for anion exchange membrane fuel cells (AEMFCs) requires identification of the active sites of the catalyst. Since not only metals but also carbon materials exhibit oxygen reduction reaction (ORR) activity in alkaline conditions, the contribution of carbon-based materials to ORR performance should also be thoroughly analyzed. However, the conventional CN− poisoning experiments, which are mainly used to explain the main active site of M−N−C catalysts, are limited to only qualitative discussions, having the potential to make fundamental errors. Here, we report a modified electrochemical analysis to quantitatively investigate the contribution of the metal and carbon active sites to ORR currents at a fixed potential by sequentially performing chronoamperometry with two reaction inhibitors, CN− and benzyl trimethylammonium (BTMA+). As a result, we discover how to quantify the individual contributions of two active sites (Pt nanoparticles and carbon support) of carbon−supported Pt (Pt/C) nanoparticles as a model catalyst. This study is expected to provide important clues for the active site analysis of carbon-supported non−Pt catalysts, such as M−N−C catalysts composed of heterogeneous elements. [ABSTRACT FROM AUTHOR]

Co and Ni 3 C nanoparticles on nitrogen doped carbon layers supported on N -doped graphene (Co@NC-Ni 3 C/G) is designed and fabricated by a two simple steps procedure for bifunctional electrocatalytic of methanol oxidation reaction (MOR) and oxygen reduction reaction (ORR). The prepared Co@NC-Ni 3 C/G-350 hybrids possess the excellent methanol oxidation current density of 44.8 mA cm−2 at potential of 1.47 V (vs. RHE), besides outstanding ORR catalytic efficiency in terms of half-wave potential (E 1/2 = 0.830 V vs RHE). [Display omitted] Designing highly efficient, long-lasting, and cost-effective cathodic and anodic functional materials as a bifunctional electrocatalyst is essential for overcoming the bottleneck in fuel cell development. Herein, a novel two-step synthesis strategy is developed to synthesize metal-organic framework (MOF) derived nitrogen-doped carbon (NC) with improved spatial isolation and a higher loading amount of cobalt (Co) and nickel carbide (Ni 3 C) nanocrystal decorated on graphene (denoted as Co@NC-Ni 3 C/G). Benefiting from multiple active sites of high N -doping level, uniform dispersion of Co and Ni 3 C nanocrystals, and a large active area of graphene, the Co@NC-Ni 3 C/G hybrids exhibit excellent methanol oxidation reaction (MOR) and oxygen reduction reaction (ORR) efficiency in an alkaline environment. For MOR, the optimized Co@NC-Ni 3 C/G-350 catalyst achieved a current density of 44.8 mA cm−2 at an applied potential of 1.47 V (V vs. RHE), which is significantly higher than Co@NC-Ni 3 C (42.07 mA cm−2) and Co@NC (24.1 mA cm−2) in 0.5 M methanol + 1.0 M KOH solutions. In addition, during the CO retention test, the Co@NC-Ni 3 C/G-350 catalyst exhibits excellent CO tolerance capacity. Excitingly, the as-prepared Co@NC-Ni 3 C/G-350 hybrid exhibits significantly improved ORR catalytic efficiency in terms of positive onset and half-wave potential (E onset = 0.90 V, E 1/2 = 0.830 V vs. RHE), small Tafel slope (34 mV dec−1) and excellent durability (only reduced 0.016 V after 5000 s test). This work provides new insights into MOF-derived functional nanomaterials for anode and cathode co-catalysts for methanol fuel cells. [ABSTRACT FROM AUTHOR]

This work proposes a cost-effective strategy to massively synthesize high-efficiency ORR electrocatalyst. [Display omitted] • A novel type of composite Co/N C was prepared. • A potential strategy was proposed to massively synthesize ORR catalysts. • High ORR activity of Co/N C triggered by Co-N heteroatomic interface. • The high stability of Co/N C in 0.1 M KOH. The development of high-efficiency and low-cost oxygen reduction electrocatalysts have become an urgent need to push fuel cells into practical application. Herein, an effective electrocatalyst Co/N C was successfully constructed, which was derived from abundant peanut shells, obtained by doping with cobalt ions and pyrolyzing in NH 3 atmosphere. Due to the abundant Co-N active sites triggered by Co-N heteroatomic interface, the prepared electrocatalysts present excellent oxygen reduction reaction (ORR) performance with more positive half-wave potential (E 1/2 = 0.83 V), incremental limiting current density (J L = 5.45 mA cm−2), higher durability and stronger resistance to methanol, which is superior to that of Pt/C (E 1/2 = 0.81 V and J L = 5.19 mA cm−2). This work proposes a potential strategy to synthesize efficient ORR electrocatalysts to instead of Pt-based catalysts. [ABSTRACT FROM AUTHOR]

An effective approach for increasing the Noble metal-utilization by decorating the atomic Pt clusters (1 wt.%) on the CoO2@SnPd2 nanoparticle (denoted as CSPP) for oxygen reduction reaction (ORR) is demonstrated in this study. For the optimum case when the impregnation temperature for Co-crystal growth is 50 °C (denoted as CSPP-50), the CoPt nanoalloys and Pt-clusters decoration with multiple metal-to-metal oxide interfaces are formed. Such a nanocatalyst (NC) outperforms the commercial Johnson Matthey-Pt/C (J.M.-Pt/C; 20 wt.% Pt) catalyst by 78-folds with an outstanding mass activity (MA) of 4330 mA mgPt−1 at 0.85 V vs. RHE in an alkaline medium (0.1 M KOH). The results of physical structure inspections along with electrochemical analysis suggest that such a remarkable ORR performance is dominated by the potential synergism between the surface anchored Pt-clusters, CoPt-nanoalloys, and adjacent SnPd2 domain, where Pt-clusters offer ideal adsorption energy for O2 splitting and CoPt-nanoalloys along with SnPd2 domain boost the subsequent desorption of hydroxide ions (OH−). [ABSTRACT FROM AUTHOR]

Platinum–dysprosium (Pt–Dy) alloys prepared by the arc melting technique are assessed as potential electrodes for the oxygen reduction reaction (ORR) using voltammetry and chronoamperometry in alkaline media. A relatively small change (10 at.%) in the alloy composition brought a notable difference in the alloys' performance for the ORR. Pt40Dy60 electrode, i.e., the electrode with a lower amount of Pt, was identified to have a higher activity towards ORR as evidenced by lower overpotential and higher current densities under identical experimental conditions. Furthermore, DFT calculations point out the unique single-atom-like coordination and electronic structure of Pt atoms in the Pt40Dy60 surface as responsible for enhanced ORR activity compared to the alloy with a higher Pt content. Additionally, Pt–Dy alloys showed activity in the oxygen evolution reaction (OER), with the OER current density lower than that of pure Pt. [ABSTRACT FROM AUTHOR]

Cathodic oxygen reduction reaction is a decisive factor for fuel cell. In this work, for the first time, we demonstrated the synthesis of N -doped carbon hollow spheres derived from conjugated microporous polymers. The resulting sample remained the inherent porosity and N component with hollow spherical morphology, which exhibits excellent ORR performance with higher limiting current density and stability than that of commercial Pt/C catalyst in alkaline solution. [Display omitted] The exploitation non-precious or metal-free electrocatalysts of oxygen reduction reaction (ORR) is of significance for construction of next-generation fuel cells. In this work, hollow-spherical conjugated microporous polymers (CMPs) comprising porphyrin units were synthesized as precursors to prepare N -doping porous carbon spheres (CMP-NP-x) by a direct pyrolysis method. The as-resulted CMP-NP-x exhibited spherical morphology with hollow structure similar to that of CMPs precursors. The BET surface area of CMP-NP-x can be tailored by the pyrolysis temperature varying from 868 m2 g−1 to 1118 m2 g−1. According to XPS analysis, the pyrrolic N content in the sample decreased but the graphitic N and pyridinic N increased with increasing of the pyrolysis temperature from 800 °C to 1000 °C. Taking advantages of porous structure with large accessible surface areas and N species active sites, the resulting CMP-NP-x showed superior ORR activity and methanol tolerance to commercial Pt/C catalyst. In particular, CMP-NP-900 possesses the highest onset potential (0.930 V), half-wave potential (0.857 V) and limiting current density of 4.45 mA cm−2, compared with Pt/C catalyst and other samples, making it a promising metal-free catalyst superior to commercial Pt/C catalyst in alkalic condition. [ABSTRACT FROM AUTHOR]

[Display omitted] • The nanoporous Ti 4 O 7 is synthesized while Pt is atomically dispersed on the Ti 4 O 7 surface by a one-step calcination method for the first time. • Carbon hollow spheres are added to the gel to synthesize nanoporous Ti 4 O 7 with high purity and specific surface area. • The as-prepared Pt/Ti 4 O 7 SAC exhibits a half-wave potential of 0.896 V and a mass activity of 4081.5 A/g Pt at 0.9 V with negligible degradation after 20,000 cycles. • Monatomic Pt electronically couples with the Tin+ to further reinforce electron delocalization. Although single atom catalyst (SAC) can maximize the atomic utilization, platinum (Pt)-based SAC is typically inactive to break the O = O bond in oxygen reduction. Herein, the nanoporous Ti 4 O 7 was synthesized while Pt was atomically dispersed on the Ti 4 O 7 surface by a one-step calcination method. The as-prepared Pt/Ti 4 O 7 SAC exhibits a half-wave potential of 0.896 V and a mass activity of 4081.5 A/g Pt at 0.9 V with negligible degradation after 20,000 cycles. Meanwhile, it exhibits a Pt utilization efficiency of 0.16 g Pt kW−1 in H 2 /O 2 fuel cell and a slight attenuation of the output current density (9.4%) after 120 h. The incorporated monatomic Pt electronically couples with the Tin+ (3 ≤ n < 4) to enhance bilateral electron transfer. The awakened Tin+ active sites synergize with monatomic Pt to moderate the adsorption intensity of O 2 and dissociate the O = O bond, opening up a four-electron pathway on the Pt-based SAC. [ABSTRACT FROM AUTHOR]

[Display omitted] • A highly curved and ultrathin P-doped PdMo bimetallene is engineered. • The catalyst has superior performance in electrooxidation of various alcohols. • The activity for ORR surpasses that of commercial Pt/C catalyst. • DFT reveals that P doping enhances both OH adsorption and CO desorption. The commercialization of direct alcohol fuel cells (DAFCs) relies on the development of high performance electrocatalysts for both the alcohol oxidation reaction and the oxygen reduction reaction (ORR). In this study, a novel phosphorus-doped palladium-molybdenum (P-PdMo) bimetallene with a partially amorphous structure is demonstrated. The ultrathin and curved morphology of the nanosheets, combined with electronic regulation by phosphorus atoms, facilitates OH adsorption and CO desorption. Consequently, the catalyst exhibits significantly enhanced activity and durability in the electrooxidation of alcohols, including methanol, ethanol, ethylene glycol, and glycerol. Particularly toward ethanol oxidation, the P-PdMo bimetallene displays exceptional mass and specific activities up to 4.95 A mg-1 Pd and 8.28 mA cm−2, respectively. Furthermore, the P-PdMo bimetallene demonstrates outstanding ORR performance, with an onset potential of 1.0 V and a half-wave potential of 0.88 V. Overall, this study opens new avenues in metallene electrocatalysts and advancing toward the practical implementation of DAFCs. [ABSTRACT FROM AUTHOR]

Efficient and stable electrocatalysts with low platinum content are crucial for the practical application of fuel cells. The development of Pt-based single atom catalysts (SACs) has emerged as a promising research direction. In this study, we design and prepare a SACs based on MoS 2 with Pt–S–Mo and Pd–S–Mo active sites (Pd, Pt–MoS 2) by successively occupying vacancies, while maintaining the individual characteristics of the active sites. The resulting Pd, Pt–MoS 2 catalyst exhibits excellent electrocatalytic activity for oxygen reduction reaction (ORR), long-term stability, and resistance to common poisons (SCN−, S2−, and methanol) under neutral conditions. Meanwhile, the microbial fuel cell (MFC) equipped with Pd, Pt–MoS 2 exhibits excellent performance in terms of actual electricity generation performance and sewage purification capacity with an ultrahigh power density, average chemical oxygen demand (COD) removal rate, and coulombic efficiency (CE) of 1398.6 ± 43.5 mW m−2, 96.2 ± 2.2 %, and 22.5 ± 0.5 %, respectively. This strategy will provide new insights into the development of advanced bimetallic as well as polymetallic doped vacancies of MoS 2 SACs. [Display omitted] • A feasible approach for the design of bimetallic single atom catalysts. • One SACs based on MoS 2 was prepared by successively occupying vacancies. • Pd, Pt–MoS 2 catalyst exhibits excellent electrocatalytic activity for ORR. • Optimized catalyst exhibits excellent capacity in electricity generation. [ABSTRACT FROM AUTHOR]

The felicitous electrolyte with advance electrodes (cathode and anode) results in the development of an improved and efficacious battery/fuel cell. Perovskite based zinc‐air batteries with biological gel electrolyte prove to outperform the aqueous batteries. In this research, a zinc‐air battery was developed using a novel biocompatible electrolyte, Guar‐gum employing LaMnO3 (LMO) perovskite as a bi‐functional electro‐catalyst. The performance of the developed perovskite catalyst in guar‐gum electrolyte was obtained and compared with the performance of the material in both polymer gel (polyvinyl alcohol‐KOH) and aqueous medium. The bi‐functional catalyst shows enhanced catalytic activity, endurance and durability in alkaline medium with an open circuit voltage of 1.40 V, power density of 9.77 mW cm−2 at the current density of 11.12 mA cm−2 and a specific capacity of 2624 mAh g−1 comparatively competent with respect to the PVA‐based battery with the specific capacitance of 753 mAh g−1. Also, the rechargeable LMO zinc‐air battery exhibited excellent cycling stability at a current density of 10 mA cm−2. Thus, the results obtained proved the competent performance of the guar‐gum electrolyte compared to the previous developed polymer electrolyte. This is how the combination of LMO in the guar‐gum electrolyte is seen to be successful for commercial use in metal‐air batteries and fuel cells. [ABSTRACT FROM AUTHOR]