Search

At present, there are few studies considering both nonlinear and fractional characteristics of suspension in vehicle systems. In this paper, a fractional nonlinear model of a quarter vehicle with two-degree-of-freedom (2-DOF) is innovatively proposed to describe the suspension system containing the viscoelastic material metal rubber. Given the lack of a general calculation scheme for the multi-degree-of-freedom fractional-order incremental harmonic balance method (IHBM), a general calculation scheme for the 2-DOF incremental harmonic balance method for nonlinear systems with fractional order is derived. The nonlinear dynamical properties of the presented model are acquired using this method. The accuracy of the proposed method is verified through a comparison with the power series expansion method. Afterward, the effects of the various parameters on the dynamic performance are analyzed. The vibration peak value of the fractional-order model is significantly higher than that of the integer-order model (IOM). Therefore, the suspension parameters should be designed with a margin when using IOM. [ABSTRACT FROM AUTHOR]

Nonlinear Model Predictive Control (NMPC) is effective for local planning of automated vehicles, especially when there exist dynamical objects and multipe requirements. But it requires many computation resources for numerical optimization, which limits its practical application becase of the limited power of onboard unit. To extend the application range of the NMPC based local planner, the coupled nonlinear vehicle dynamics model is adopted based on the numerical analysis, which conversely requires much more discretization poits for acceptable accuracy. For better computation efficiency, Lagrange polynomials are used to discretize the vehicle dynamics model and objective function with less points and fine numerical accuracy. Furthermore, an adaptive strategy is designed to determine the order of Lagrange polynomials according to running state by numerical analysis of discretization error. Both acceleration effect and performance of the local planner designed by NMPC are validated by experimental tests under scenarios with multiple dynamical obstacles. The test results show that compared with the original one the accuracy and efficiency are improved by 74% and 60%, respectively. [ABSTRACT FROM AUTHOR]

Four-wheel steering (4WS) is an effective technique to improve handling performance and lateral stability of road vehicles. Conventionally, controllers utilise the driver's actions and vehicle dynamics to coordinate front and rear-axle steering. This paper proposes a novel approach for 4WS controller design, based on the concept of Artificial Flow Guidance (AFG), which relies on a spatially distributed motion reference through a two-dimensional vector field. This field provides high-level guidance while lower-level steering controllers to control axle centres motions relative to the flow. These flow vectors, computed in real-time via simple geometric construction, can be pre-computed globally to evaluate the guidance algorithm's efficacy. When controlling only the front axle, this same approach can function as an autonomous driving system. Relying solely on a spatial reference field and control targets' velocities enables the controller to work in a simple and robust fashion, without using a reference vehicle dynamics model or lengthy parameter tuning. The proposed approach's effectiveness is validated through co-simulation with MATLAB/Simulink and the CarMaker simulation platform. AFG control performance is found to be at least comparable to that of more complex 4WS controllers using methods such as MPC; in the cases considered, AFG provides superior path-tracking performance. [ABSTRACT FROM AUTHOR]

The paper presents a novel control strategy for autonomous vehicles, which can effectively handle the nonlinear effects and uncertainties of the controlled system. This solution is based on a new formulation of the ultra-local model-based control approach. This method can deal with the unknown dynamics and other uncertainties of the vehicle without any further measurement or complex modelling process. The control methods require a reduced-complexity nominal linear model of the system, and the unknown part is continuously estimated by the proposed ultra-local model. The proposed control-oriented vehicle modelling method leads to an increased performance level of vehicle motion. The effectiveness of the proposed method through a high-fidelity vehicle simulator (CarMaker) is illustrated. Moreover, the operation of the control through its implementation on a test vehicle of ThyssenKrupp is also demonstrated. [ABSTRACT FROM AUTHOR]

Semi-active primary suspensions are an effective means of improving ride quality in high-speed railway vehicles in relation to the mitigation of car-body bending vibration. In this paper, prototype magnetorheological (MR) dampers are tested and the results are used to define a mathematical model of the dampers. Then, three control schemes for semi-active primary suspensions are proposed: Skyhook, LQG and Mix-1-Sensor, and their performance is assessed by means of Hardware-In-the-Loop (HIL) tests considering a simple quarter-vehicle model which is run on a real-time board and set in interaction with one physical MR damper. The results show that all three considered control strategies lead to a reduction of car-body vibration by around 30% and a very good agreement is found between HIL tests and numerical simulations in which the physical damper is replaced by the mathematical damper model. The damper model is finally interfaced with a flexible multi-body model of the complete vehicle to provide further assessment of semi-active control. The results of the latter simulations show that the semi-active suspension could provide an improvement of the $ {N_{mvz}} $ N mvz ride quality index in the order of 40–45% with respect to the passive vehicle for all three control schemes. [ABSTRACT FROM AUTHOR]

Polygonalization is a typical non-uniform wear phenomenon that affects the performance and comfort of the vehicle/track system. Therefore, the vehicle system performance could be strictly troubled by polygonal damage close to the wheel circumference at the wheel/rail contact. A 3D vehicle/track an EMU type train consisting of 8 coupled vehicles model has been established. The coupled model car body and bogie frame are considered rigid and integrated with the flexible wheelset, rail, and slab track to investigate the elastic deformation caused by the impact load induced by the wheel polygonalization. The flexible track can be incorporated into the multi-body vehicle model using the movable reference frame formulation. Uncertainty parameters are presented, such as passenger weight, wind force, coefficient friction, and suspension variation. The proposed research is validated based on the existing research work and shows excellent agreement. The simulation result deliberated the vertical wheel-rail force, wheelset acceleration, rail acceleration, rail displacement, and slab track acceleration. The results of this study show that as the wheel polygonal damage amplitude increase, the value of wheel/rail normal forces and the dynamic vibrational response of the wheelset axle increase. Additionally, polygonal wear-induced impact stresses may cause the wheelset axle to resonate. When wheel polygonal damage amplitude and uncertainty parameters are corporate into the system dynamics, the maximum magnitude of the wheelset, rail, and slab track acceleration increases. Besides, the train failure degree is comparable to the polygonised wheel harmonic order, defect parameters, and amplitude of out-of-roundness. [ABSTRACT FROM AUTHOR]

Collision accidents of construction vehicles frequently occur during the construction of building projects. It is difficult to warn of collision risk efficiently by using the safety control methods of on-site inspection and viewing surveillance video. Therefore, a novel collision risk warning model for construction vehicles is proposed in this paper. The model comprises a state awareness module and a collision risk assessment module. In the state awareness module, the YOLOv7 algorithm is used to identify and locate construction vehicles. The DeepSORT algorithm is used for the real-time tracking of construction vehicles. Finally, the state awareness module obtains a wealth of sensing information and provides it to the collision risk assessment module. In the collision risk assessment module, the speed assessment method and the minimum safety distance assessment method of construction vehicles are innovatively proposed and compiled. In the speed assessment method, the speed of construction vehicles is calculated and speeding warnings are performed using the transformation matrix between latitude and longitude coordinates and image pixel coordinates. In the minimum safety distance assessment method, the original surveillance picture is converted into a bird's eye view (BEV) of the world coordinate system through inverse perspective mapping (IPM). Then the distance of all construction vehicles is traversed, and the visual warning of the minimum safe distance is provided. The effectiveness and robustness of this collision risk warning model were verified by taking three practical projects in different construction stages as examples. The research results show that the mean average precision (mAP@0.5:0.95) of the construction vehicles collision risk warning model can reach 89.10%, and it has a good tracking effect and an efficient collision risk warning strategy. [ABSTRACT FROM AUTHOR]

Direct yaw moment control (DYC) can effectively improve the yaw stability of four-wheel distributed drive electric vehicles (4W-DDEVs) under extreme conditions, which has become an indispensable part of active safety control for 4W-DDEVs. This study proposes a novel hierarchical DYC architecture for 4W-DDEVs to enhance vehicle stability during ever-changing road conditions. Firstly, a vehicle dynamics model is established, including a two-degree-of-freedom (2DOF) vehicle model for calculating the desired yaw rate and sideslip angle as the control target of the upper layer controller, a DDEV model composed of a seven-degree-of-freedom (7DOF) vehicle model, a tire model, a motor model and a driver model. Secondly, a hierarchical DYC is designed combining the upper layer yaw moment calculation and low layer torque distribution. Specifically, based on Matlab/Simulink, improved linear quadratic regulator (LQR) with weight matrix optimization based on inertia weight cosine-adjustment particle swarm optimization (IWCPSO) is employed to compute the required additional yaw moment in the upper-layer controller, while quadratic programming (QP) is used to allocate four motors' torque with the optimization objective of minimizing the tire utilization rate. Finally, a comparative test with double-lane-change and sinusoidal conditions under a low and high adhesion road surface is conducted on Carsim and Matlab/Simulink joint simulation platform. With IWCPSO-LQR under double-lane-change (DLC) condition on a low adhesion road surface, the yaw rate and sideslip angle of the DDEV exhibits improvements of 95.2%, 96.8% in the integral sum of errors, 94.9%, 95.1% in the root mean squared error, and 78.8%, 98.5% in the peak value compared to those without control. Simulation results indicate the proposed hierarchical control method has a remarkable control effect on the yaw rate and sideslip angle, which effectively strengthens the driving stability of 4W-DDEVs. [ABSTRACT FROM AUTHOR]

Trajectory tracking on a low-speed vehicle using the model predictive control (MPC) algorithm usually assumes a simple road terrain. This assumption does not correspond to the actual road situation, leading to low tracking accuracy. Therefore, a trajectory tracking method considering road curvature based on MPC is proposed in this paper. In this method, the controller can automatically switch between MPC types. Linear model predictive control (LMPC) is selected for small road curvatures, while nonlinear model predictive control (NMPC) is employed for large road curvatures. In addition, the NMPC algorithm in this work considers the effect of road curvature on tracking accuracy, making it suitable for tracking time-varying curvature roads. To verify the feasibility of the algorithm, simulation comparisons with the basic MPC model were carried out at different testing roads and vehicle longitudinal speeds. The results indicate that the method significantly improves trajectory tracking accuracy, all while ensuring real-time calculations. The intelligent switching capability of control models based on road curvature allows its application to track trajectories on arbitrarily complex roads. [ABSTRACT FROM AUTHOR]

Carrier-free ultra-wideband sensors have high penetrability anti-jamming solid ability, which is not easily affected by the external environment, such as weather. Also, it has good performance in the complex jungle environment. In this paper, we propose a jungle vehicle identification system based on a carrier-free ultra-wideband sensor. Firstly, a composite jungle environment with the target vehicle is modeled. From this model, the simulation obtains time-domain echoes under the excitation of carrier-free ultra-wideband sensor signals in different orientations. Secondly, the time-domain signals are transformed into MTF images through the Markov transfer field to show the statistical characteristics of the time-domain echoes. At the same time, we propose an improved RepVGG network. The structure of the RepVGG network contains five stages, which consist of several RepVGG Blocks. Each RepVGG Block is created by combining convolutional kernels of different sizes using a weighted sum. We add the self-attention module to the output of stage 0 to improve the ability to extract the features of the MTF map and better capture the complex relationship between characteristics during training. In addition, a self-attention module is added before the linear layer classification output in stage 4 to improve the classification accuracy of the network. Moreover, a combined cross-entropy loss and sparsity penalty loss function helps enhance the performance and accuracy of the network. The experimental results show that the system can recognize jungle vehicle targets well. [ABSTRACT FROM AUTHOR]

To increase vehicle dynamics modelling accuracy in simulation environments, in this work, we propose a model, where the mutual influence of the vehicle dynamics and tyre wear is taken into account. In this context, simulation-oriented models aim at representing the main features of the vehicle dynamics, while keeping the complexity low, making them suitable for control-oriented analyses and design. The wear model quantifies tyre wear as a tyre mass loss depending on the tyre-road interaction, derived from the vehicle dynamics and kinematics; then, the outcome of this model is consequently used to update the tyre friction characteristics, by modifying the main parameters of the Pacejka's magic formula. We also discuss the steps required to use the model in two-wheeled vehicles, where the roll dynamics plays an important role in the tyre wear. The main features of the developed model are discussed on a motorcycle, as a simulation case-study. [ABSTRACT FROM AUTHOR]

In a typical traffic scenario, automated vehicles are required to interact with surrounding traffic participants, e.g. human-driven vehicles, pedestrians, etc. In this paper, a novel adaptive authority allocation strategy considering the social behaviours of surrounding vehicles is proposed for the shared steering control (SSC) of automated vehicles. First, a Koopman-based potential-field-driven distributed model predictive control (K-PF-DMPC) method is proposed for the modelling of vehicle interaction to describe surrounding vehicle's social behaviour. This method effectively deals with the nonlinearity embedded in the non-cooperative game-based vehicle interaction model, so that the analytical form of Nash equilibrium can be derived for a fast online solution. Then, the SSC system of the automated vehicle is implemented by a weighted summation method. To balance the driving performance and intervention degree while considering the surrounding vehicles' social behaviours, a hybrid fuzzy strategy (HFS) is proposed for allocating the control authority between the driver and automation. The value of authority allocation coefficient is calculated by fusing the outputs from two shared fuzzy controllers, i.e. the enhanced and weakened shared fuzzy controllers, in accordance to the belief of the surrounding vehicle's type. Several numerical simulations and driver-in-the-loop simulator experiments are conducted for validation. Results show that the proposed strategy can provide appropriate steering intervention to the driver owing to the consideration of the surrounding vehicle's social behaviour and obtains the best driver-automation collaboration performance compared with the comparative groups. [ABSTRACT FROM AUTHOR]

To solve the problem of trajectory tracking lateral control in autonomous driving technology, a model predictive control (MPC) controller trajectory tracking lateral control method combined with a deep deterministic policy gradient algorithm (DDPG) is proposed in this paper. This method inputs the real-time state of the vehicle into DDPG to achieve real-time automatic optimization of the prediction time domain and control time domain parameters of the MPC controller, and then affects the specific performance of the MPC controller in trajectory tracking lateral control. Specifically, the state space, action space, and reward function of DDPG are defined, and the automatic driving trajectory tracking lateral controller is designed in combination with the vehicle dynamics model. To reduce the exploration space of DDPG and improve the training efficiency of the entire model, the technique of advantage-disadvantage experience separation and extraction is introduced. Finally, the proposed method was trained and verified in various scenarios, and compared with two other lateral control methods for autonomous driving. The results showed that the learning and training time of the trajectory tracking lateral control method based on DDPG-MPC was shorter than that of the DDPG-based method, and the evaluation indicators in the trajectory tracking control process were better than those of the DDPG-based method and original MPC-based method. [ABSTRACT FROM AUTHOR]

A split-type two-axle vehicle for bridge indirect measurement is proposed to address the deficiencies of single-axle and conventional two-axle vehicles. At first, the conceptual design of the split-type two-axle vehicle is put forth, and the analytical solution for the vehicle-bridge interaction (VBI) system response is derived. After that, the regularity of the vehicle frequency response function is studied, and the numerical analysis method is utilized to validate the analytical solution. Based on the theoretical findings, the vehicle frequency and speed are studied to investigate their impacts on extracting bridge frequencies from vehicle responses. The results indicate that a peak will form in the frequency response function (FRF) curves when the input frequency is near to the vehicle frequency. The single peak phenomenon will occur when the zero-point condition of the FRF from the contact point to the vehicle body is remarkably close to the second vibration frequency of the vehicle. It is preferable for the first frequency of the vehicle to be higher than that of the bridge since this helps to extract the bridge frequency. On the other hand, at low speeds (≤ 43.2km/h), higher vehicle speeds will result in a greater distance between the peaks of the left- and right-shifted frequencies of the bridge, wider frequency bands, and lower spectral resolution, which is not conducive to bridge frequency identification. [ABSTRACT FROM AUTHOR]

This paper investigates the problem of tracking target control of a nonlinear system in the context of cyber-physical systems for connected autonomous vehicles with external unknown disturbances. A new robust tracking strategy via backstepping sliding-mode control is proposed. First, a connected nonlinear vehicle dynamical model with disturbances is constructed. Then, a disturbance observer is presented to approximate the unknown disturbances when the derivative of the disturbance is bounded. This paper has proved that the error of the observation can converge to zero in finite time. Third, a tracking control method is designed which combines the backstepping method with the sliding-mode method. According to the method, the estimated values of interference are used as a priori knowledge. Furthermore, the stability of the designed control strategy is demonstrated through using the Lyapunov theory. Finally, simulation experiments are presented to demonstrate the feasibility of the proposed approaches. [ABSTRACT FROM AUTHOR]

This paper proposes a learning-based control approach for autonomous vehicles. An explicit Takagi–Sugeno (TS) controller is learned using input and output data from a preexisting controller, employing the Adaptive Neuro-Fuzzy Inference System (ANFIS) algorithm. At the same time, the vehicle model is identified in the TS model form for closed-loop stability assessment using Lyapunov theory and LMIs. The proposed approach is applied to learn the control law from an MPC controller, thus avoiding the use of online optimization. This reduces the computational burden of the control loop and facilitates real-time implementation. Finally, the proposed approach is assessed through simulation using a small-scale autonomous racing car. [ABSTRACT FROM AUTHOR]

To promote the application of automated vehicles in large airports, in this study, we present an integrated optimization method for scheduling Unmanned follow-me cars. The scheduling process is divided into three phases: Dispatch, Guidance, and Recycle. For the Dispatch phase, we establish a vehicle assignment model, to allocate the vehicle resource equitably. For the Guidance phase, we offer an quantitative way, to measure the spacing between Unmanned follow-me car and aircraft. To optimize the efficiency of airport operation in the three phases and ensure safety, the collaborative planning model, and the conflict prediction model are established. An improved grey wolf optimization algorithm is adopted to enhance the convergence speed and generalization performance. A case study at Ezhou Huahu Airport in China demonstrates the effectiveness of the methods. The results show that the model of collaborative planning can make the balance of path selection, Unmanned follow-me car's working time, and departure sequence. The convergence speed of the improved algorithm has been increased by 18.75%. The inequity index of vehicle assignment is only 0.015731, and the spatiotemporal distribution of conflicts is influenced by the airport's surface layout. [ABSTRACT FROM AUTHOR]

Accurate vehicle acceleration prediction is useful for developing reliable Advanced Driving Assistance Systems (ADAS) and improving road safety. The existence of driver heterogeneity magnifies the variations in acceleration data, leading to consequential impacts on the precision of vehicle acceleration prediction. However, few studies have fully considered the driver heterogeneity when predicting vehicle acceleration. To model the characteristics of individual drivers, this study first identifies the driving behavior semantics which is defined as the underlying patterns of driving behaviors. The analysis results from the coupled hidden Markov model (CHMM) are used to evaluate the driving behavior differences between different drivers by Wasserstein distance. Then the convolutional neural network (CNN) and long short-term memory (LSTM) network are applied to predict vehicle acceleration. To validate the accuracy of the proposed prediction framework, vehicle acceleration data in car-following conditions is extracted from the safety pilot model deployment (SPMD) dataset. The segmentation results indicate that the CHMM possesses a robust capacity for modeling driving behavior. The prediction results demonstrate that the proposed framework, which incorporates driver clustering before prediction, significantly improves the accuracy of predictions. And the CNN-LSTM outperforms the LSTM in predicting vehicle acceleration during car-following scenarios. The findings from this study can enhance the development of personalized functionalities within ADAS to promote its deployment, thereby improving its acceptance and safety. [ABSTRACT FROM AUTHOR]

In response to the strength performance requirements of the new energy Off road Vehicle steering system, this article analyzes and studies the strength performance and failure modes of the new energy Off road Vehicle steering rod based on a certain new energy Off road Vehicle model through simulation, bench experiments, and vehicle strength testing teams. Based on various vehicle misuse conditions, the force law of the steering rod under different vehicle driving conditions was analyzed, and a load spectrum for the steering rod strength bench test was developed to meet the actual vehicle usage conditions. The results indicate that the steering rod strength failure is mainly manifested as bending failure of the compression rod under alternating tension and compression conditions. Finally, based on the stability principle of the compression rod, the requirements for the strength performance index of the steering rod are proposed. The research results can provide certain technical support for the strength assessment of the vehicle steering rod. [ABSTRACT FROM AUTHOR]

This paper optimizes the assignment of shared automated vehicles under users' uncertain departure times. Automated vehicles can drive themselves, so no staff are needed to relocate vehicles in the one-way carsharing system. To optimize fleet placement and use, a twophase solution method was established. Phase 1 strategically distributes vehicles across stations using a system optimization approach, while Phase 2 tracks vehicle movements via an agent-based simulation model. Phase 1 solutions serve as inputs to Phase 2 simulations. Using a fleet size of roughly 10,000 vehicles, case study applications were run across the Austin, Texas region's six-county network. In the base case setting, results suggest that system profits are optimized when vehicle rental is priced at $1.28=km ($0.8=mi). The number of proactive vehicle relocations falls 9.8% if the relocation operation cost rises from $0.096=km ($0.06=mi) to $0.32=km ($0.2=mi). Average per-trip profit is $10.60 when using high-cost vehicles, and $11.60 when using low-cost vehicles. Results from a 3-h simulation show an average person-trip length of 25 km (15.6 mi), with 29.6 min of average driving time. When a 24-h day was simulated, the vehicle-occupied time and vehicle-distance traveled were 4 h and 200 km (125 mi) per vehicle-day, respectively. The low coefficient of variation of satisfied demand across 30 demand scenarios suggests the robustness of the two-phase solution method. [ABSTRACT FROM AUTHOR]

To investigate the vibration characteristics of off-road vehicles resulting from external excitations, this study explores a vibration modelling approach that accounts for the coupling of roll and pitch. A low-frequency vibration test was conducted, and the results were analysed in both the time domain and frequency domains. The mathematical model of the tractor was validated, affirming the accuracy of the off-road vehicle modelling method. This study focuses on the Shandong Wuzheng Group Co., Ltd. Renoman 2104 ratio tractor prototype (1:18) as the research subject. A vibration mathematical model and simulation model were developed, taking into account the coupled vibrations in both roll and pitch directions. Key parameters of the tractor, including damping, stiffness, centroid, inertia, and road roughness, were acquired through experimental testing. Upon comparing the numerical simulation model results with the experimental data, the findings reveal a 6.2% error between the left front axle test data and the simulation, and a 6.1% error for the right front axle. The vertical vibration primary frequency in the test is 13.1Hz, while the numerical simulation model registers 11.8 Hz, resulting in a relative error of 10%. Notably, the numerical simulation model exhibits significant consistency with the experimental results. These outcomes serve as a valuable reference for the parameter design and vibration control of off-road vehicles. • A vibration modelling approach of off-road vehicles is proposed. • The coupling vibration of pitch and roll is considered. • The methodology for acquiring tractor dynamic parameters has been elucidated. • An analysis of both time domain and frequency domain results was conducted to validate the mathematical model of the tractor. [ABSTRACT FROM AUTHOR]

In this paper, a typical motion-based modelling and tracking issue is investigated for vehicle targets in linear road segment by a variable structure multiple model (VSMM) method. Vehicle target motions in a road with multiple lanes are described by typical lane keeping and lane changing manoeuvres. To describe trajectories of typical manoeuvres, an Ornstein–Uhlenbeck process and a sine half-cycle are used to model lane keeping and lane changing motions in lateral direction, respectively. Note that starting point and length of lane changing motion are unknown in target tracking. Time-varying model sets are designed based on the current motion model with different motion parameters. A VSMM tracking frame is constructed to obtain target state estimates with time-varying model set. The effectiveness of the proposed typical motion-based tracking scheme is displayed by simulation results on road vehicle tracking. [ABSTRACT FROM AUTHOR]

A comprehensive RFD-FTC-DCA system is proposed for the hypersonic vehicle with saturation constraints to resist the control surface damage, actuator faults, disturbances and parameter perturbation. Firstly, the hypersonic vehicle fault model is established. Secondly, the robust fault detection (RFD) observer is designed to detect the control surface damage and actuator faults accurately under the influences of disturbances and parameter perturbation. Thirdly, the fault-tolerant control (FTC) law is designed to resist the control surface damage, actuator faults, disturbances and parameter perturbation simultaneously. Finally, a dynamic control allocation (DCA) algorithm is designed to reallocate the FTC law and limit the deflection angle and velocity within saturation constraint. The comparison simulation results are presented to demonstrate that the RFD observer can detect the faults accurately and reduce false alarm rates effectively, the FTC law can resist the control surface damage, actuator faults, disturbances and parameter perturbation simultaneously, and the tracing errors of attack angle, side-slip angle and roll angle are only $ \pm 0.7^\circ $ ± 0.7 ∘ , $ \pm 0.2^\circ $ ± 0.2 ∘ and $ \pm 1.5^\circ $ ± 1.5 ∘ , respectively, and the DCA algorithm can reallocate the FTC law and limit the deflection angle and velocity within saturation values. [ABSTRACT FROM AUTHOR]

The purpose of this study is to extend the mileage by improving the efficiency of the electric vehicle (EV) driving and thermal management system (TMS). The powertrain system and the TMS must be considered simultaneously from the architecture stage as complementary systems to maintain the driving performance of the EV. This paper proposes an EV architectural design method and a multi-physical EV modeling technique. The main components of the EV are standardized differently from those of the internal combustion engine (ICE) vehicle, and the TMS is designed by thermal system configuration. Therefore, instead of the traditional continuous variable-based design methodology, optimal combination design based on the component database (DB) and the configuration plot presents the combinational design method. The performance of an EV varies depending on the performance of driving components and TMS, and weather. This paper presents a Modelica-based vehicle modeling technique to integrate multiple physical phenomena. Finally, we implemented an automated design using the optimal combination design method and the multi-physical integrated vehicle model design framework. The design of the C-segment EV was carried out to review the validity of the proposed method. 2880 laboratories were planned and designed using design variables with 10 levels of mixing. As a result of the design, we have confirmed that the mileage increases by 5% compared to the previous one in NEDC mode. [ABSTRACT FROM AUTHOR]

The application of 'Target Cascading' in the product development process is well known to be effective in various industry fields, and it is a methodology that is already actively applied in various forms in the field of vehicle Ride & Handling (R&H) performance development. This paper proposes a model-based vehicle performance benchmarking methodology and a technology for setting system characteristics to achieve handling performance objectives as a means of utilization for this. Rather than introducing already well-known target deployment techniques, a process is proposed for practical use in the vehicle development phase through the development of interfaces between low degrees of freedom vehicle model and optimization software. The methodology presented in this study is expected to be available in a timely manner as a practical vehicle performance development tool. [ABSTRACT FROM AUTHOR]

Objective: Excessive skin exposure to deleterious environmental variables results in inflammation as well as molecular and cellular impairments that compromise its functionality, aesthetic qualities, and overall well‐being. The implementation of topical administration of antioxidants and other compounds as a method for preventing or reversing damage is a rational approach. Numerous phenolic compounds derived from plants have demonstrated capabilities such as scavenging free radicals and promoting tissue healing. However, the primary obstacle lies in effectively delivering these compounds to the specific place on the skin, and accurately forecasting their diffusion through the skin can assist in determining the most effective tactics. Hence, this article provides a comprehensive analysis of recent literature pertaining to the in vitro skin diffusion characteristics of plant phenolics. The aim is to gain a deeper understanding of their behaviour when present in various forms such as solutions, suspensions, and formulations. Method: The data on plant extracts and isolated plant phenolic compounds in vitro skin diffusion assays published over the last six years were compiled and discussed. Results: Even though the gold standard Franz diffusion cell is the most commonly used in the assessment of in vitro plant phenolic skin diffusion profiles, a plethora of skin models and assay conditions are reported for a variety of compounds and extracts in different vehicles. Conclusion: The presence of numerous models and vehicles poses a challenge in creating correlations among the existing data on plant phenolic compounds. However, it is possible to draw some general conclusions regarding molecular, vehicle, and skin characteristics based on the gathered information. [ABSTRACT FROM AUTHOR]

We present a general approach to model the motion of a rigid body ground vehicle on a smooth nonplanar road surface. We generalise planar control-oriented models while preserving standard model states, inputs and outputs. We derive our approach from first principles, apply it to existing vehicle modelling approaches and test it through real-world experiments. We demonstrate that our approach improves upon the prediction accuracy of planar models. [ABSTRACT FROM AUTHOR]

This study introduces a deep learning surrogate model designed to predict the evolution of the mean pressure coefficient on the back face of a Windsor body across a range of yaw angles from 2. 5 ∘ to 10 ∘ . Utilizing a variational autoencoder (VAE), the model effectively compresses snapshots of back pressure taken at yaw angles of 2. 5 ∘ , 5 ∘ , and 10 ∘ into two latent vectors. These snapshots are derived from wall-modeled large eddy simulations (WMLESs) conducted at a Reynolds number of R e L = 2.9 × 10 6 . The frequencies that dominate the latent vectors correspond closely with those observed in both the drag's temporal evolution and the dynamic mode decomposition. The projection of the mean pressure coefficient to the latent space yields an increasing linear evolution of the two latent variables with the yaw angle. The mean pressure coefficient distribution at a yaw angle of 7. 5 ∘ is predicted with a mean error of e ¯ = 3.13 % when compared to the WMLESs results after obtaining the values of the latent space with linear interpolation. [ABSTRACT FROM AUTHOR]

With the implementation of strict emission regulations and the use of cleaner fuels, there has been a considerable reduction in exhaust emissions. However, the relative contribution of tire wear particles (TWPs) to particulate matters is expected to gradually increase. This study conducted laboratory wear experiments on tires equipped on domestically popular vehicle models, testing the factors and particle size distribution of TWPs. The results showed that the content of tire wear particle emission was mainly ultrafine particles, accounting for 94.80% of particles ranging from 6 nm to 10 μm. There were at least two concentration peaks for each test condition and sample, at 10~13 nm and 23~41 nm, respectively. The mass of TWP emission was mainly composed of fine particles and coarse particles, with concentration peaks at 0.5 μm and 1.3–2.5 μm, respectively. Both the number and mass of TWPs exhibited a bimodal distribution, with significant differences in emission intensity among different tire samples. However, there was a good exponential relationship between PM10 mass emissions from tire wear and tire camber angle. The orthogonal experimental results showed that the slip angle showed the greatest impact on TWP emission, followed by speed and load, with the smallest impact from inclination angle. [ABSTRACT FROM AUTHOR]

Several technological challenges delay the adoption of electrified powertrains in the heavy-duty transport sector. For fuel-cell hybrid electric trucks, key issues include slow cold start, reduced cooling power during high ambient temperatures, and uncertainties regarding durability. In addition, the engineers must handle the complexity of the system. In this article, a Matlab/Simulink library is introduced, which has been developed to aid engineers in the design and optimization of energy management systems and strategies of this complex system that consider mechanical, electrochemical, and thermal energy flows. The library is introduced through five example vehicle models, and through case studies that highlight the various kinds of analysis that can be performed using the provided models. All library code is open source, open for commercial use, and runs in Matlab/Simulink without any need for external libraries. [ABSTRACT FROM AUTHOR]

Aiming at the demand for subjective evaluation of driveability for fuel cell vehicles, the modeling and evaluation method of driveability for fuel cell vehicles were studied in this paper. Firstly, a real-time model of the fuel cell vehicle powertrain system was established, which included the fuel cell model, power battery model, DC/DC converter model and drive motor model. Secondly, it was integrated with the vehicle dynamics model to form a virtual prototype of a fuel cell vehicle. And a virtual subjective evaluation platform for fuel cell vehicles was built by combining the virtual prototype and high-fidelity driving simulator. Thirdly, a subjective evaluation method of driveability for fuel cell vehicles was proposed, which included the starting performance, acceleration performance, uniform speed performance and tip-in/tip-out performance. Finally, the paper used the platform and method mentioned above to conduct subjective evaluations of the fuel cell vehicles. [ABSTRACT FROM AUTHOR]

This article considers a path tracking control problem for autonomous vehicles constrained to maintain a safe distance from the next vehicle in the lane. The control design problem is solved by considering a mathematical model of the vehicle that jointly describes the lateral and longitudinal dynamics. Specifically, the ℒ2$$ {\mathcal{L}}_2 $$ optimal controller is designed aimed at minimizing the orientation and position tracking errors with respect to a given reference path. Moreover, the controller is able to ensure that the vehicle can both follow a speed profile and automatically adjusts the vehicle speed to maintain a proper distance from the next vehicle. The lateral dynamic is regulated by a 2‐DOF feedforward/feedback controller, where the feedforward law is implemented by exploiting an inverse kinematic model of the vehicle. On the other side, the feedback action, along with the action of the controller in charge to regulate the longitudinal dynamics, is the ℒ2$$ {\mathcal{L}}_2 $$ optimal gain‐scheduling state‐feedback controller. In particular, a parameter‐dependent quadratic Lyapunov function approach is used to reduce the conservativeness of the solution and a suitable convex LMI optimization problem is formulated for the synthesis. The vehicle is described by a seven‐degrees‐of‐freedom (7DOF) full‐car model, with the tire‐generated forces described by the classical Pacejka's Magic Formula. In order to assess the performance of the proposed control strategy, simulations have been undertaken in Matlab/Simulink by considering an autonomous vehicle driving into an urban scenario. [ABSTRACT FROM AUTHOR]

• A comprehensive vertical dynamics model of the electric vehicle considering the integrated powertrain system is proposed. • The limitations of traditional vertical dynamics model of electric vehicle in the high frequency range are revealed. • The effects of mounting stiffness and damping on the vibration of chassis and integrated powertrain system are explored. • A multi-objective optimization model is designed to minimize the vibration of chassis and integrated powertrain system. Integrated powertrain system, mainly composed of driving motor and reducer, is one of the excitation sources to electric vehicle vibration but is limited in coupling with the vertical vehicle dynamic in the existing research, which restricts the reliability of dynamics investigation of vehicle and integrated powertrain system. This work proposes a novel vertical dynamic model of the electric vehicle considering the integrated powertrain system, enabling the way to access the coupled vibration among the chassis, unsprung mass, and integrated powertrain system. The road irregularity, unbalanced magnetic pull, and gear mesh excitation are developed and are further applied to the novel vehicle dynamic model with ten degrees of freedom (DOFs). Then, the dynamic response between the novel model and traditional one is compared. Further, the effects of the stiffness and damping of suspension and mounting on the vibration of chassis and integrated powertrain system are explored by numerical calculation. Finally, a multi-objective optimization model is proposed and is driven by the dragonfly algorithm to minimize the vibration of chassis and integrated powertrain system. The research results shown that there will be present the new complex dynamic characteristics with considering the excitation from the integrated powertrain system. The suspension and mounting parameters have the nonlinear effects on the vehicle vibration. And the system vibration can be globally optimized with the optimization algorithm. [ABSTRACT FROM AUTHOR]

The huge growth in the number of vehicles is causing serious traffic management problems. Existing roads must handle traffic more than expected which presents serious challenges including congestion and safety. Intelligent traffic management systems were proposed as a solution to solve such problems. This intelligent system is charged to estimate vehicle density and manage the traffic flow accordingly. A wide variety of sensors was deployed for the traffic management system such as cameras, ultrasonic sensors, radar, infrared sensors, and acoustic sensors. In this work, an intelligent traffic flow management system was proposed based on data provided by public surveillance cameras. For this purpose, a real-time vehicle detection and counting model based on You Look Only Once (YOLO) v6 was deployed. The proposed model was trained and evaluated on different publicly available datasets such as BDD 100K and KITTI. Extensive experimentations proved the efficacy of the proposed model for detecting vehicles while operating under real-time constraints. The proposed traffic flow management system was evaluated using real videos for different traffic scenarios, and good results were achieved. [ABSTRACT FROM AUTHOR]

The vibration of high-speed trains induced by track irregularities is a main factor affecting ride comfort. Especially, the long-wavelength track irregularities can reduce the passengers' ride comfort by increasing the vibration of the high-speed trains. A three-dimensional human body model coupled to a vehicle body and tracks is established to form a coupled human-seat-vehicle-track system for investigating the influence of the long-wavelength track irregularities on ride comfort. The parameters of the seated human model are determined by measurement based on the multi-island GA method. The coupled model is then used to evaluate the ride comfort of high-speed trains using ISO 2631 under the excitation of the track longitudinal level irregularities. The effects of primary, secondary suspension, and seat support vertical stiffness and damping on ride comfort are analysed. The results show that the track's longitudinal irregularities lead to high human body vibration levels and large ride comfort indices (lower ride comfort), especially when the irregularity excitation frequency is near the natural frequency of the high-speed train. The passengers' ride comfort is more sensitive to the vertical secondary suspension stiffness than the other suspension parameters. [ABSTRACT FROM AUTHOR]

Multi-intelligent vehicles forming and maintaining a specific formation during traveling can save energy consumption and road resources, and improve traffic efficiency and driving safety. Centered around the Cooperative Vehicle Infrastructure(CVI) framework of the Internet of Vehicles(IOV), this paper delves into the control objectives of forming multi-intelligent vehicle formation, explores the theory of formation shaping process, and investigates the optimization of energy consumption in the formation shaping process. First, the clustering design is used to take the kinematic process of vehicles as an optimization process from the bionics, taking the instantaneous consumption indexes as the optimization objectives. Then, optimize the acceleration inputs of the vehicle formation process using the improved Artificial Fish Swarm Algorithm(AFSA), and iterate with the clustering algorithm part, so as to realize the formation shaping process with energy consumption as the optimization objective. Finally, ajoint simulation platform built by Simulation of Urban Mobility (SUMO) and Python is used for simulation verification, and the results show that the formation shaping process can be realized and achieve the optimal energy consumption under the scenarios proposed in this paper, thus verifying the validity of the clustering model of vehicle formation shaping and the energy consumption optimization algorithm designed in this paper. [ABSTRACT FROM AUTHOR]

Research on evaluating highway bridge performance through vehicle-bridge interaction (VBI) analysis has made significant advancements. However, when assessing driving comfort, using vehicle acceleration instead of human acceleration poses challenges in accurately representing comfort. First, the paper proposes a finite element analysis method for human-vehicle-bridge spatial interactions (HVBSIs). Then, the importance of wheel path roughness difference is explored when assessing driving comfort. Furthermore, a new method for evaluating driving comfort that includes human and vehicle vibration responses has been proposed, and a simulation example of the steel-concrete composite beam bridge (SCCBB) is used to verify the effectiveness of the proposed method. The results demonstrate that the HVBSI analysis method effectively simulates the interconnected vibrations of the human body, the spatial vehicle model, and the three-dimensional (3D) bridge model. Differences in wheel path roughness significantly impact the roll vehicle vibration responses, which are crucial in driving comfort analysis. The driver's body vibration response is essential for evaluating driving comfort, and its inclusion leads to increased comfort indices values. In comparison to traditional methods, the overall vibration total value (OVTV) increases by a maximum of 109.04%, and the level of weighted vibration ( L e q ) increases by a maximum of 6.74%. This leads to an upgrade from grade IV to grade V in terms of comfort level, indicating a reduced comfort. [ABSTRACT FROM AUTHOR]

Vehicle antilock systems play a very important role in the stability and reliability during vehicle braking. Due to the complexity of the braking process, antilock braking system (ABS) usually face the problems such as nonlinearity, time-varying, and uncertain parameter modeling. Thus, aiming at the parameter model uncertainty problem of ABS, an adaptive neural network sliding mode controller (ADRBF-SMC) is designed in this paper. On this basis, establishing the quarter-vehicle model and the seven-degree-of-freedom vehicle model, and treating the difference between the two models as a kind of disturbance, carrying out vehicle braking performance simulation experiments to analyze the variation of braking performance parameters such as vehicle and wheel speeds, slip ratio, braking distance, braking torque, under the three cases of adaptive neural network sliding mode controller, traditional sliding mode controller, and no control. Simulation results show that the adaptive neural network sliding mode controller (ADRBF-SMC) proposed in this paper can play an effective control role in both vehicle dynamics models. In addition, the control method proposed in this paper has stronger anti-interference capability and higher robustness compared with the sliding mode controller (SMC). [ABSTRACT FROM AUTHOR]

This study investigates the particle dispersion characteristics in the turbulent wake of a simplified vehicle model (Ahmed body) for two values of the rear slant angle ϕ (25 ° and 40 °) to study the effect of flow separation. In the experiments (Reynolds number Rel=1.90 × 10 5 ), smoke particles were released from a source and visualized with a laser sheet. Concentration fields were analyzed to calculate the vertical (Sy) and lateral (Sz) smoke spread. The findings indicate that the flow topology and concentration fields in the wake are highly dependent on ϕ. In the ϕ = 40 ° case, separation on the rear slant disrupts the trailing vortices originating on the rear slant edges and significantly alters the wake topology. The growth of vertical smoke spread saturates after the recirculation region. The uniform mixing and absence of trailing vortices concentrate the smoke particles in the model midplane. In the ϕ = 25 ° case, the signatures of trailing vortices were observed in the concentration fields behind the model. The vertical smoke spread is less, and the lateral smoke spread is more compared to the ϕ = 40 ° case. The growth of the smoke spread ( S y , S z ) driven by the trailing vortices persists for a long distance, even after the recirculation region. The disruption of trailing vortices brought about by the flow separation appears to be an important effect driving the vertical smoke spread in the wake. The connection between the turbulent velocity structures and concentration structures will need to be explored with combined velocity and concentration measurements in the wake. [ABSTRACT FROM AUTHOR]

This paper considers the scheduling of electric vehicles in a public transit system. Our main innovation is that we take into account that charging stations have limited capacity, while also considering partial charging. To solve the problem, we expand a connection-based network in order to track the state of charge of vehicles and model recharging actions. We then formulate the electric vehicle scheduling problem as a path-based binary program, whose linear relaxation we solve using column generation. We find integer feasible solutions using two heuristics: price-and-branch and a diving heuristic, including acceleration strategies. We test the approach using data from the concession Gooi en Vechtstreek in the Netherlands, containing up to 816 trips. The diving heuristic outperforms the other heuristic and solves the entire concession within seven hours of computation time with an optimality gap of less than 3%. Supplemental Material: The online appendix is available at https://doi.org/10.1287/trsc.2022.0253. [ABSTRACT FROM AUTHOR]

Within the urban road system, traffic conflicts most frequently are concentrated at road intersections, and left-turning traffic is a prominent and pivotal factor leading to intersection conflicts. The scarcity of applied models that can comprehensively elucidate the shifting trajectory dynamics and exit lane selection behavior of left-turning vehicles has posed challenges to the accurate analysis and prediction of intersection vehicle conflict patterns. This study extracted trajectories of left-turning vehicles at intersections from video data. A vehicle left-turn trajectory model was formulated, hinging on changes in trajectory curvature. Moreover, leveraging geometric intersection parameters and video data, a vehicle exit lane selection model was devised using random utility theory. This model integrates variables such as intersection turning angle, vehicle type, entrance lane position, vehicle speed, following clearance, and the lead vehicle’s position in the exit lane. The outcomes indicate that left-turn trajectories can be approximated well with a flat curve, and the trajectory’s curvature has a quadratic parabolic correlation with the intersection’s aspect ratio. The trajectory model presented in this paper adeptly characterizes left-turning vehicle movement across diverse intersections. Similarly, the exit lane selection model adeptly forecasts the distribution of left-turning vehicles in exit lane positions. This predictive efficacy stems from the recognition that turning angle, entrance lane vehicle position, and vehicle speed profoundly impact the exit lane choice for left-turning vehicles. This research sheds light on the intricacies of driving behavior and exit lane selection of left-turning vehicles at signalized intersections. By focusing on these critical aspects, this study offers valuable insights that contribute to the improvement of intersection design and overall traffic safety. [ABSTRACT FROM AUTHOR]