Search

In cold environments, the low temperature slows down microbial metabolisms, such as the biodegradation processes of hydrocarbons, which are often stimulated by the addition of dispersants in oil spill disasters. In this study, we investigated the effects of hydrocarbon water-accommodated fraction (WAF) prepared with and without dispersant on benthic microbial communities in a microcosm experiment in which hydrocarbon removal was observed. Both WAFs contained similar polycyclic aromatic hydrocarbon (PAH) content. The microcosm experiment, set up with either pristine or contaminated sediments, was conducted for 21 days at 4 °C under WAF and WAF + dispersant conditions. The behavior of bacterial communities in response to WAF and WAF + dispersant was examined at both DNA and RNA levels, revealing the effect of WAF and WAF + dispersant on the resident and active communities respectively. The contaminated sediment showed less taxa responsive to the addition of both WAF and WAF + dispersant than the pristine sediment, indicating the legacy effect by the presence hydrocarbon-degrading and dispersant-resistant taxa inhabiting the contaminated sediment., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Dispersants are approved for use in many countries (UK, South Korea, Australia, Egypt, France, Greece, Indonesia, Italy, Japan, Malaysia, Norway, Singapore, Spain, Thailand, and several coastal African, South American, and Middle Eastern countries). Here, the protocols of the most advanced (France, Norway, UK, Spain, Greece, Italy, USA, and Australia) are compared for identifying possible harmonization of approval procedures. Pre-toxicity testing, recognized oil datasets, common thresholds, standardized protocols, zoning, and monitoring are some of the aspects that can be discussed between countries., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

After oil spills occur, dispersed oil droplets can collide with suspended particles in the water column to form the oil-mineral aggregate (OMA) and settle to the seafloor. However, only a few studies have concerned the effect of chemical dispersant on this process. In this paper, the mechanism by which dispersant affects the surface properties of kaolin and the viscosity and oil-seawater interfacial tension (IFT ow ) of Roncador crude oil were separately investigated by small-scale tests. The results indicated that the presence of dispersant impairs the zeta potential and enhances the hydrophobicity of kaolin. The viscosity of Roncador crude oil rose slightly as the dosage of dispersant increased, while IFT ow decreased significantly. Furthermore, the oil dispersion and OMA formation at different dispersant-to-oil ratio (DOR) were evaluated in a wave tank. When DOR was less than 1:40, the effect of dispersant on the dispersion of spilled oil was not obvious. With the increasing DOR, the effect became more pronounced, and the adhesion between oil droplets and kaolin was inhibited. The size ratio between oil droplets and particles is the significant factor for OMA formation. The closer the oil-mineral size ratio is to 1, the more difficultly the OMA forms., (© 2021. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

In recent years, EU countries have recognized national policies to authorize dispersant use to mitigate the petroleum hydrocarbon contamination in case of unintentional oil spills at sea. A harmonization of dispersant approval procedures is needed because the application of different methodologies agrees on dissimilar toxic responses for the same dispersant in different European countries. Actually, different dispersant approval procedures are applied in France and Italy with one French mandatory toxicity test and three Italian bioassays accompanied with different criteria of toxicity classification. In this paper, a harmonized tiered approach is proposed to address the dispersant ecotoxicological assessment in these two nations. Our approach, applicable at the European level, introduces two mandatory tests (algal growth inhibition test and mortality test with crustaceans) and one discretionary test (fish mortality test), by reducing use of vertebrates as much as possible in accordance with humane principles and animal welfare.

This work reports the role of different dispersants, namely, polyethylene glycol (PEG 200 2%), ethylene glycol 5%, ethanol 2%, dimethyl sulfoxide (DMSO 5%), and polyvinyl alcohol (PVA 5%) in the toxicity profile of several commercial nanomaterials (NM), such as hydrophilic and hydrophobic TiO 2 , hydrophilic SiO 2 , SiO 2 in aqueous suspension (aq), and ZnO towards the bioluminescent bacterium Aliivibrio fischeri. The majority of NM showed tendency to form agglomerates in the different dispersants. Although some particle agglomeration could be detected, DMSO at 5% was the best dispersant for hydrophobic TiO 2 NM while PVA at 5% was the most effective dispersant for the other types of NM. Average size was not the most relevant aspect accounting for their toxicity. A remarkable reduction in average size was followed by a decrease in NM toxicity, as demonstrated for SiO 2 aq. in PVA 5%. Contrarily, despite of high particle agglomeration, ZnO NM showed a higher toxicity to bacteria when compared with other tested NM. Independently of the average particle size or surface charge, the dispersant either enhanced the toxicity to bacteria or acted as physical barrier decreasing the NM harmful effect to A. fischeri.

Considering the accumulation and high consumption of activating agents, anhydrous ethanol (AE) could be used to dissolve them to improve the dispersion effect, which was an effective way of improving the practical utilization rate. In this study, FeCl 2 was dissolved in AE and further impregnated cotton textile waste (CTW) to prepare activated carbons (ACs) by pyrolysis. Afterward, ACs prepared in optimal conditions determined by the orthogonal experiment evaluated the physicochemical properties and adsorption capacities for Cr(VI). The results illustrated that AE greatly increased the dispersion of FeCl 2 on CTW, reduced the conventional impregnation dosage, and remarkably improved the activation efficiency. Textural analyses revealed that ACs exhibited excellent porosity properties and graphite carbon structure. FeCl 2 catalyzed the decomposition of volatile substances to produce gaseous products and promoted the transformation of amorphous carbon to graphite carbon that was conducive to pore development, followed by the formation of developed micropores and crystal structures. The adsorption performance of ACs was estimated using Cr(VI), and the adsorption was fitted with the pseudo-second-order kinetic and the Langmuir isotherm. Furthermore, the ACs possessed superior magnetization and reusability. Graphical abstract.

Dispersants including Tween 20, Tween 40, Tween 60, and polyacrylic acid (PAA) were used to modify nanoscale zero-valent iron (nZVI). All dispersants dispersed nZVI effectively. PAA-modified nZVI was more stable than nZVI that was modified with Tween surfactant. Iron nanoparticles that were prepared using 0.5-5.0% (vol%) of PAA remained in suspension for more than 2 h. nZVI that was modified using Tween surfactant remained in suspension for 30-60 min, and there was complete sedimentation of bare iron in 10 min. When 2.0-5.0% (vol%) of Tween surfactant was used, the stability of the nZVI that was modified using Tween 20 was much better than that for nZVI that was modified using Tween 40 or Tween 60. The results for the transportation test show that nZVI that was prepared using 2% (vol%) of Tween 20 exhibited the best mobility in porous media. Approximately 83-90% of TCE was degraded by bare, PAA-modified, and Tween 20-modified nZVI, and about 63-67% of TCE was removed by nZVI that was modified using Tween 40 and Tween 60 during 20 days of reaction. The production of cis-dichloroethene (DCE) and 1,1-DCE demonstrates that TCE is removed via reductive dechlorination. The results of this study show that PAA- and Tween 20-modified nZVI are more practical for in situ remediation because they exhibit good mobility and degrade TCE effectively.

In this study, shrimp waste was enzymatically hydrolyzed to generate a green dispersant and the product was tested for crude oil dispersion in seawater. The hydrolysis process was first optimized based on the dispersant effectiveness (DE) of the product. The functional properties of the product were identified including stability, critical micelle concentration, and emulsification activity. Water was confirmed as a good solvent for dispersant generation when compared with three chemical solvents. The effects of salinity, mixing energy, and temperature on the dispersion of the Alaska North Slope (ANS) crude oil were examined. Microtox acute toxicity test was also conducted to evaluate the toxicity of the produced dispersant. In addition, DE of the product on three different types of crude oil, including ANS crude oil, Prudhoe Bay crude oil (PBC), and Arabian Light crude oil (ALC) was compared with that of the Corexit 9500, respectively. The research output could lead to a promising green solution to the oil spill problem and might result in many other environmental applications.

Pathways underlying the effect of fuel oil and dispersant on cell cycle and macromolecular synthesis in the chlorococcal alga Scenedesmus armatus are explored. Growth dynamics and proliferation events in synchronos alga cultures in a media containing dispersant DP-105, oil and a combination of oil and dispersant, were studied. Presence of oil effected an inactivation of protoplast fission event. Presence of oil hindered nuclear cell division.

Nanocomposite microparticles (NCMPs) have been used in various solid dosage forms with the goal of enhancing the dissolution rate and bioavailability of poorly water-soluble drugs. Nanoparticle recovery from NCMPs, i.e., redispersion, is the preliminary step in drug dissolution. This study aims at exploring aqueous redispersion of NCMPs with various dispersants under quiescent vs. agitated conditions as potential dispersant screening tool in the development of fast-dissolving NCMP formulations. NCMPs were prepared by coating wet-milled suspensions of a poorly water-soluble drug, griseofulvin (GF), formulated with the dispersants hydroxypropyl cellulose (HPC), sodium dodecyl sulfate (SDS), as-received/wet co-milled croscarmellose sodium (CCS), and mannitol, onto Pharmatose® carrier particles in a fluidized bed dryer. The NCMPs were added to quiescent water kept in a cuvette, and the redispersion was visualized and investigated by turbidimetry and dynamic light scattering. The morphological evolution of a single NCMP exposed to a drop of water was studied via optical microscopy, which provided further insight into the self-redispersibility. As a comparison, the NCMPs were also redispersed in water agitated by a paddle stirrer followed by centrifugation and drug assay of the resultant supernatant, which yielded the percentage of GF recovered as nanoparticles. Both quiescent and agitated redispersion methods yielded similar rank-ordering of the dispersants: NCMPs with either HPC/SDS or HPC/CCS exhibited effective nanoparticle recovery and fast dissolution, whereas those with HPC or HPC/mannitol led to poor redispersibility and slow dissolution. This study demonstrates that both quiescent and agitated redispersion tests could be used for screening/optimizing dispersants for fast-dissolving drug NCMP formulations.

Hyperbranched polyglycerol (HPG) is modified with dodecanethiol (DS) via the "thiol-ene" click reaction to obtain an amphiphilic product DSHPG. The molecular structures of DSHPG samples are characterized by NMR, FTIR, and GPC, and the thermal behaviors are characterized by DSC and TGA. Gold nanoparticles (Au NPs) are prepared with DSHPG as the stabilizer and surface-modification reagent. The size of Au NPs can be tuned by changing the molecular weight of HPG. It is observed that the HPG molecular weights of 1123, 3826, and 55,075 lead to the NP diameters of 4.1 nm for Au@DSHPG-1, 9.7 nm for Au@DSHPG-2, and 15.1 nm for Au@DSHPG-3, respectively. The morphology and size of Au NPs are characterized by TEM and DLS. Especially, the dispersion abilities of Au NPs in different pure solvents and co-solvent mixtures are investigated. The long alkyl chains on DSHPG give the ability of Au NPs to be well dispersed in nonpolar solvents. Hydrocarbon-based nanofluids can be obtained from the hydrophobic Au NPs dispersed into a series of hydrocarbons. The dispersion stability for Au NPs in hydrocarbons is monitored by UV-Vis spectroscopy, and the relative concentration of Au NPs is observed to still maintain over 80% after 3600 h.

Chemical dispersants can be a beneficial method for breaking up oil slicks; however, their use in mitigation could pose potential toxic effects on the marine ecosystem. Dispersants may be transported to lower salinity habitats, where toxicity data for aquatic species have not been established. This study examined the effect of salinity on oil dispersant toxicity in the eastern mud snail, Ilyanassa obsoleta, using two dispersants authorized for oil spill response, Corexit® 9500A and Finasol® OSR 52. Median lethal toxicity values (LC50) and sublethal effects were examined at 10, 20, and 30 ppt salinity in adult and larval mud snails. Two biomarkers (lipid peroxidation and acetylcholinesterase) were used to measure sublethal effects. The 96-h static renewal LC50 values indicated significant differences in toxicity between dispersants and salinities. Larval snails were significantly more sensitive than adult snails to both dispersants, and both life stages were significantly more sensitive to Finasol than to Corexit. Larval snails were more sensitive to dispersants at lower salinity, but adult snails were more sensitive at higher salinities. Dispersants increased lipid peroxidation and decreased acetylcholinesterase activity. These results demonstrate that dispersant toxicity varies among compounds and organism life stages, and that physicochemical properties of the environment, such as salinity, can affect the potential toxicity to estuarine species.

The present study aimed to examine whether the use of dispersant would be suitable for favoring the hydrocarbon degradation in coastal marine sediments without impacting negatively micro- and macrobenthic organisms. Mudflat sediments, maintained during 286 days in mesocosms designed to simulate natural conditions, were contaminated or not with Ural blend crude oil (REBCO) and treated or not with third-generation dispersant (Finasol OSR52). While the dispersant did not lead to an increase of hydrocarbon biodegradation, its use enables an attenuation of more than 55 % of the sediment concentration of total petroleum hydrocarbons (TPH). Canonical correspondence analysis (CCA) correlating T-RFLP patterns with the hydrocarbon content and bacterial abundance indicated weak differences between the different treatments except for the mesocosm treated with oil and dispersant for which a higher bacterial biomass was observed. The use of the dispersant did not significantly decrease the macrobenthic species richness or macroorganisms' densities in uncontaminated or contaminated conditions. However, even if the structure of the macrobenthic communities was not affected, when used in combination with oil, biological sediment reworking coefficient was negatively impacted. Although the use of the dispersant may be worth considering in order to accelerate the attenuation of hydrocarbon-contaminated mudflat sediments, long-term effects on functional aspects of the benthic system such as bioturbation and bacterial activity should be carefully studied before.

In many coastal countries, oil spill contingency plans include several alternatives for removal of the spilled oil from the ocean. Frequently, these plans include dispersants. Because this process applies chemical substances that may add toxicity to oil that already contains toxic compounds, it is, at times, a controversial method to fight oil pollution. Additionally, local conditions may result in particular complications. We investigated the possible effects of the dispersant Corexit 9500© under conditions similar to those of subtropical oceans. We used fuel oil #6+ diesel as the test mixture. Under certain conditions, at least part of the dispersed oil may reach the sediment, particularly if the dispersant is applied in coastal waters. Nine experimental units were used in this experiment. Similar conditions of water temperature, salinity, air fluxes into the experimental units, and hydrocarbon concentrations in sediments were used. Two treatments and one control, each one with three replicates, were carried out. We concentrated our investigation on sediment, although measurements of water were also taken. Our results suggest that once the oil has penetrated the sediment, no significant differences exist between oil that contains dispersant and oil without dispersant. Noticeable degradation of aliphatic hydrocarbons occurred mainly in the low molecular weight aliphatic hydrocarbons and not in the others. Apparently, degradation of aromatics was easier than that of alkanes. However, some differences were noticed for the degradation of PAHs in the sediment, suggesting a faster degradation under particular conditions in aerobic environments such as under this experiment.

The Special Monitoring of Applied Response Technologies (SMART) program was used during the Deepwater Horizon oil spill as a strategy to monitor the effectiveness of sea surface dispersant use. Although SMART was implemented during aerial and vessel dispersant applications, this analysis centers on the effort of a special dispersant missions onboard the M/V International Peace, which evaluated the effectiveness of surface dispersant applications by vessel only. Water samples (n = 120) were collected from background sites, and under naturally and chemically dispersed oil slicks, and were analyzed for polycyclic aromatic hydrocarbons (TPAHs), total petroleum hydrocarbons (TPH), and a chemical marker of Corexit (dipropylene glycol n-butyl ether, DPnB). Water chemistry results were analyzed relative to SMART field assessments of dispersant effectiveness ("not effective," "effective," and "very effective"), based on in situ fluorometry. Chemistry data were also used to indirectly determine if the use of dispersants increased the risk of acute effects to water column biota, by comparison to toxicity benchmarks. TPAH and TPH concentrations in background, and naturally and chemically dispersed samples were extremely variable, and differences were not statistically detected across sample types. Ratios of TPAH and TPH between chemically and naturally dispersed samples provided a quantitative measure of dispersant effectiveness over natural oil dispersion alone, and were in reasonable agreement with SMART field assessments of dispersant effectiveness. Samples from "effective" and "very effective" dispersant applications had ratios of TPAH and TPH up to 35 and 64, respectively. In two samples from an "effective" dispersant application, TPHs and TPAHs exceeded acute benchmarks (0.81 mg/L and 8 μg/L, respectively), while none exceeded DPnB's chronic value (1,000 μg/L). Although the primary goal of the SMART program is to provide near real-time effectiveness data to the response, and not to address concerns regarding acute biological effects, the analyses presented here demonstrate that SMART can generate information of value to a larger scientific audience. A series of recommendations for future SMART planning are also provided.

In this study we report the preparation of nanohybrid dispersant molecules based on pyrene and polyhedral oligomeric silsesquioxanes for non-covalent functionalization of multi-walled carbon nanotubes (MWCNTs). The prepared dispersant improves the dispersion of MWCNTs in organic solvents with very different polarities such as tetrahydrofuran, toluene, and n-hexane. The functionalized MWCNTs were used to introduce conductivity into polydimethylsiloxane membranes which can be used for electrostatic discharge applications.

Five dispersant-molecule models of succinimide, acrylate, imide, phenylsulfonic and salicyl were used to study their interactions with the water surface (001). The interaction energy, molecular configuration, charge distribution and radial distribution function (RDF) curve for each of the dispersant molecules were analyzed from the molecular mechanics (MM) and molecular dynamics (MD) simulation results. It can be seen that the system energies, mostly electrostatic and hydrogen bond energies, were reduced significantly when the dispersant molecules interacted with the water surface. The hydrophilic group of a dispersant molecule can attach itself to the water surface firmly and reach for a stable energy-minimized configuration, which is helpful to the dispersants' dispersancy. The influence exerted by the hydrophobic group of the dispersant molecule, which was the substituted hydrocarbon chain of n-octadecanyl in this paper, is discussed in comparison with the naked polar headgroup. Steric configuration, charge distribution and substitute hydrocarbon chain of the dispersant molecule influenced the interaction between dispersants and polar water surface.

Context: This study explores the interaction between particles in microplastic semi-coke water slurry at the molecular level using molecular simulation methods, specifically DFT calculations and MD simulations. In addition, the experiment of slurry preparation was carried out to study the viscosity and stability of the slurry. The electrostatic potential analysis shows that the interaction between microplastics and dispersant molecules occurs on atoms with large electronegativity or oxygen-containing functional groups, and the energy gap of frontier molecular orbitals indicated that PVC interacts most easily with the dispersant (0.39 eV), followed by PS (1.08 eV) and PET (3.65 eV). In addition, it is also noted that due to the steric hindrance effect, the adsorption energy was opposite to the DFT calculation results: PET was - 213.338 kcal/mol (NNO) which was highest, followed by PS (- 107.603 kcal/mol, NNO), and PVC (NNO) was lowest which was - 94.808 kcal/mol. And RDF shows similar results, which the probability of water molecules in the PET system was the highest, followed by PS, and finally, PVC. The MD results are consistent with the viscosity and stability characterization results of the slurry which PET has the lowest viscosity of 87.3 mPa·s. Finally, this study provides new ideas for the treatment of microplastics and the improvement of the performance of semi-coke water slurry and reveals the interaction mechanism between microplastics and semi-coke water slurry., Methods: All calculations were performed using Materials Studio (MS) version 2020 software, BIOVIA Corporation. The DFT calculation was carried out through the DMol 3 module. The DFT calculations include electron density, electrostatics, orbitals, and population analysis. In DMol 3 module, the GGA-PBE function was selected to consider gradient changes in density in the simulated calculation. The DFT-D correction was selected, and all electrons were calculated by DNP for accurate core potentials and the DNP file was 4.4. MD simulation was performed through the Forcite module. MD simulation mainly focuses on relative concentration distribution analysis, radial distribution function, and adsorption energy calculation. All molecular geometry optimizations are performed in the Forcite module. In the molecular dynamic part, all simulations used PCFF forcefield. The NVT ensemble was adopted and using the Nosé thermostat., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

A method of dispersive liquid-liquid microextraction, based on the dispersion of an extractant by the gas phase formed as a result of a phase transition, i.e., the evaporation of a highly volatile nonpolar organic solvent (dispersant) upon heating the extraction,-is developed. The analytical capabilities of the method are shown in the determination of preservatives (sorbic and benzoic acids) in soft drinks for baby food by high-performance liquid chromatography with photometric detection. The extractant and the dispersant for the microextraction of preservatives are chosen a terpenoid and a highly volatile organochlorine solvent, respectively, which excluded the use of polar organic solvents for dispersing phases, with which the distribution coefficients are reduced. The limits of detection (3[sigma]) for sorbic and benzoic acids are 0.3 mg/L. The developed method does not require centrifugation for phase separation., Author(s): M. A. Kochetkova [sup.1] , I. I. Timofeeva [sup.1] , A. V. Bulatov [sup.1] Author Affiliations: (1) grid.15447.33, 0000 0001 2289 6897, Institute of Chemistry, St. Petersburg State University, [...]

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous contaminants generally found in complex mixtures. PAHs are known to cause pleiotropic effects on living organisms, including developmental defects, mutagenicity, carcinogenicity and immunotoxicity, and endocrine disruptions. The main goal of this study is to evaluate the toxicity of water-accommodated fractions (WAFs) of oils in two life stages of the Japanese medaka, larvae and juveniles. The deleterious effects of an acute exposure of 48 h to two WAFs from Arabian light crude oil (LO) and refined oil from Erika (HO) were analyzed in both stages. Relevant endpoints, including ethoxy resorufin-O-deethylase (EROD) activity, DNA damage (Comet assay), photomotor response, and sensitivity to nervous necrosis virus (NNV) infection, were investigated. Larvae exposed to both oil WAFs displayed a significant induction of EROD activity, DNA damage, and developmental anomalies, but no behavioral changes. Deleterious effects were significantly increased following exposure to 1 and 10 μg/L of LO WAFs and 10 μg/L of HO WAFs. Larval infection to NNV induced fish mortality and sharply reduced reaction to light stimulation. Co-exposure to WAFs and NNV increased the mortality rate, suggesting an impact of WAFs on fish defense capacities. WAF toxicity on juveniles was only observed following the NNV challenge, with a higher sensitivity to HO WAFs than to LO WAFs. This study highlighted that environmentally realistic exposure to oil WAFs containing different compositions and concentrations of oil generated high adverse effects, especially in the larval stage. This kind of multi-marker approach is particularly relevant to characterize the toxicity fingerprint of environmental mixtures of hydrocarbons and PAHs., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Fish are currently used models for the toxicity assessment of chemicals, including polycyclic aromatic hydrocarbons (PAHs). Alternative methods including fish cell lines are currently used to provide fast and reliable results on the toxic properties of chemicals while respecting ethical concerns about animal testing. The Rainbow trout liver cell line RTLW1 was used to analyze the effects of two water-accommodated fractions from two crude oils: Arabian Light crude oil (LO) and refined oil from Erika (HO). Several toxicity endpoints were assessed in this study, including cytotoxicity, EROD activity, DNA damage (comet and micronucleus assays), and ROS production. RTL-W1 cells were exposed for 24 h at two or three dilutions of WAF at 1000 µg/L (0.1% (1 μg/L), 1% (10 μg/L), and 10% (100 μg/L)) for cytotoxicity and EROD activity and 1% and 10% for ROS production and genotoxicity). Exposure of RTL-W1 cells to LO WAF induced a significant increase of EROD activity and ROS production and altered DNA integrity as revealed by both the comet assay and the micronucleus test for 10 µg/L of LO. On the other hand, HO WAF exhibited limited toxic effects except for an EROD induction for 1% WAF dilution. These results confirmed the usefulness of RTL-W1 cells for in vitro toxicological assessment of chemical mixtures., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

The production of renewable materials from alternative sources is becoming increasingly important to reduce the detrimental environmental effects of their non-renewable counterparts and natural resources, while making them more economical and sustainable. Chemical surfactants, which are highly toxic and non-biodegradable, are used in a wide range of industrial and environmental applications harming humans, animals, plants, and other entities. Chemical surfactants can be substituted with biosurfactants (BS), which are produced by microorganisms like bacteria, fungi, and yeast. They have excellent emulsifying, foaming, and dispersing properties, as well as excellent biodegradability, lower toxicity, and the ability to remain stable under severe conditions, making them useful for a variety of industrial and environmental applications. Despite these advantages, BS derived from conventional resources and precursors (such as edible oils and carbohydrates) are expensive, limiting large-scale production of BS. In addition, the use of unconventional substrates such as agro-industrial wastes lowers the BS productivity and drives up production costs. However, overcoming the barriers to commercial-scale production is critical to the widespread adoption of these products. Overcoming these challenges would not only promote the use of environmentally friendly surfactants but also contribute to sustainable waste management and reduce dependence on non-renewable resources. This study explores the efficient use of wastes and other low-cost substrates to produce glycolipids BS, identifies efficient substrates for commercial production, and recommends strategies to improve productivity and use BS in environmental remediation., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Marine oil snow (MOS) potentially forms after an oil spill. To fully understand the mechanism of its formation, we investigated the effects of suspended particles (SP) and dispersants on MOS formation of crude oil and diesel oil by laboratory experiments. In the crude oil experiment, the SP concentration of 0.2 g L -1 was more suitable for crude oil MOS formation. The addition of dispersants significantly stimulated N and TV during MS/MOS formation of SP at 0.4 g L -1 and 0.8 g L -1 concentration (p < 0.05). Without SP, the dispersants also stimulated crude oil MOS formation. Furthermore, the concentration of SP had a significantly positive effect on the reduction of the total amount of N-alkanes (p < 0.05). In the diesel oil experiment, after adding dispersants to diesel oil, the maximum N, D m , and TV values at a SP concentration of 0.2 g L -1 were significantly higher than those at 0.4 g L -1 and 0.8 g L -1 (p < 0.05). Besides, we found that dispersants stimulated MOS formation in diesel oil at a SP concentration of 0.2 g L -1 . However, the dispersants had an inhibitory effect on diesel oil MOS formation without SP. Notably, the MOS formed by diesel oil appeared white, unlike the black MOS associated with crude oil. These findings are important for the environmental impact of oil spills and elevated SP concentrations., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

In situ burning (ISB) is discussed to be one of the most suitable response strategies to combat oil spills in extreme conditions. After burning, a highly viscous and sticky residue is left and may over time pose a risk of exposing aquatic biota to toxic oil compounds. Scientific information about the impact of burn residues on the environment is scarce. In this context, a comprehensive ISB field experiment with approx. 1000L IFO 180 was conducted in a fjord in Greenland. The present study investigated the toxicity of collected ISB residues to early life stages of zebrafish (Danio rerio) as a model for potentially exposed pelagic organisms. The toxicity of ISB residues on zebrafish embryos was compared with the toxicity of the initial (unweathered) IFO 180 and chemically dispersed IFO 180. Morphological malformations, hatching success, swimming behavior, and biomarkers for exposure (CYP1A activity, AChE inhibition) were evaluated in order to cover the toxic response on different biological organization levels. Across all endpoints, ISB residues did not induce greater toxicity in zebrafish embryos compared with the initial oil. The application of a chemical dispersant increased the acute toxicity most likely due to a higher bioavailability of dissolved and particulate oil components. The results provide insight into the adverse effects of ISB residues on sensitive life stages of fish in comparison with chemical dispersant application.

Nowadays, although dispersants have been widely applied for emergency response to oil spills, they are potentially hazardous to the marine ecosystem. Therefore, it is necessary to evaluate dispersants' toxicity in a practical and integrated way before their large-scale application. Here, we compared the acute toxicity of five chemical dispersants (concentrate RS-I, conventional RS-I, HLD-501, Fuken-2, and Weipu) to three species (a microalgae Platymonas helgolandica, a mollusk Ruditapes philippinarum, and a luminescent bacterium Acinetobacter sp. Tox2) which represent different trophic levels. Our results showed that (1) conventional RS-I was slightly toxic to all the three test organisms; (2) concentrate RS-I and Weipu were slightly toxic to R. philippinarum, but were not toxic to the other two test species; (3) Fuken-2 and HLD-501 exhibited no acute toxicity to the three test organisms. Our results could provide information on toxicity data derived from multiple test organisms for the use of these five dispersants in the future.

In this work, the effect of waste brake oil (WBO) on the dispersion property of coal-sludge oil slurry (CSOS) was investigated and comprehensively analyzed. Apparent viscosity of CSOS decreases from 997 to 276 mPa.s with the increasing of SS content from 0 to 12% under the calorific value (CV) of 17.70 MJ/kg and oil/sludge ratio (O/S) of 2.0. The combination of sewage sludge (SS) and WBO could decrease the apparent viscosity of CSOS, and SS content and O/S are two important parameters to affect the apparent viscosity. WBO mainly contains the hydrocarbon compound and a lot of oxygenated functional groups according to its GC/MS results. WBO could cover on the surface of SS and coal particle, and reduce their hydrophobic character and the adsorbance amount of dispersant based on the FTIR, XPS and adsorption performance results. In addition, the mechanism of WBO on slurry characteristics of CSOS was investigated. With the low content of WBO, the liquid bridges from WBO force the solid particles to adhere together and form a stable network structure, thus reducing the flow ability of the suspension. With the increasing of WBO, the network structures could be broken into cells, resulting in a dramatic decrease in viscosity. This research provides a potential way to dispose the SS and waste industry oil., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Municipal sludge (MS) is used to prepare coal water slurry (CWS). This practice is beneficial for resource utilization and reduces treatment costs and environmental pollution. In this study, alkali-modified municipal sludge (AMS) was prepared with Ca(OH) 2 as modifier and mixed with coal to produce AMS-CWS. The effect and mechanism of MS and AMS on slurry ability, stability, and combustion characteristics of the CWS were explored. The results of the pulping experiments showed that the slurry concentration of the AMS-CWS was approximately 10% greater than that of MS-CWS. The water separation rates of MS-CWS and AMS-CWS were 5% and 5.26%, respectively, which were 13.62% and 13.36% less than that of CWS (18.62%). The zeta potential experiments verified these results. Combustion performance research shows that both MS and AMS have positive effects on combustion performance. The results of the contact angle experiments showed that the hydrophobicity of AMS was enhanced, which was beneficial for improving the pulping capacity of MS-CWS., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

To evaluate the pollution level and health risk of total petroleum hydrocarbon (TPH), seawater, sediments, and aquatic organisms were sampled from the southern sea area of Zhejiang Province (Yangtze River Delta, China) between 2017 and 2019. TPH was widely present in the aquatic environment and products, and its concentration was highly variable. The average value of pollution index (PI) exceeded 1 from 2017 to 2018, and 45.46-69.19% of seawater samples and 56.87-50.00% of sediment samples were polluted. The results showed significant differences in the TPH concentration in various species of aquatic organisms. The average TPH value in aquatic organisms could be ranked in the order as follows: bivalve > shrimp > crab > fish, further reflecting that the ability to accumulate and metabolize TPH existed differently among aquatic organisms within the same pond aquaculture environment. It was relatively safe to eat aquatic products since the exposure risk index was found to be far below the threshold value in this study. Therefore, it would be prudent to undertake regular monitoring of TPH to ensure effective ecosystem functioning and seafood safety in the southern Zhejiang ocean., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

In this paper, the production of pyrolyzed oil in lab scale plant and its possible use in variable speed diesel engine with nanoparticle and secondary fuel oxy-hydrogen gas is investigated. The pyrolyzed oil is produced from waste tires in lab scale plant, and after its distillation, it is blended with neat diesel in the proportion of 20:80 (TDF). The different testing fuels are prepared by mixing nanoparticle CeO 2 (NP) at the concentrations 50 ppm and 100 ppm with blended fuel (named as TDF-NP50 and TDF-NP100). While in the testing phase, the HHO gas is supplied through specially designed venturi at fixed flow rate (fuel designated as TDF-NP50-HHO and TDF-NP100-HHO). The focus of current investigation is to investigate the combined impact of inducting HHO with nanoparticle mixed pyrolyzed blends on engine performance and emissions characteristics. The pyrolyzed blended fuel deteriorate the BTE, BSFC, emissions of HC and NOx while improves the CO emission. The improvement in all the characteristics can be achieved by introducing CeO 2 nanoparticle at 50 ppm and 100 ppm which improves BTE by 15-24%, BSFC by 2.2-4.2%, HC by 8-18%, CO by 7-12%, and NOx by 7-16%. The further improvement can be achieved by inducting HHO gas, which are BTE 11%, BSFC 5-8%, HC 15%, and CO 13-16%. However, the NOx emission is increased by 14-17%. Hence, the waste tire-derived pyrolyzed oil along with green hydrogen and nanoparticles CeO 2 can be used as a sustainable transportation fuel in existing CI engine., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

A synergistic photocatalytic system based on Fe-based perovskite with persulfate was constructed for alkali lignin (AL) degradation in pulp and paper wastewater. The degradation performance and mechanism on AL were carried out under ambient temperature and pressure, accompanied by visible light irradiation. The results showed that the synergistic photocatalytic system exhibited much better performance on AL degradation than the single catalytic system. The degradation efficiency reached 73.5% under the optimal conditions and was constant at around 65% over the pH range from 2 to 8. A significant escalation of the AL degradation was observed at pH 10, reaching 80.1%. The photogenerated holes, 1 O 2 and SO 4 - ·, generated by the system were involved in the degradation, and the holes played a dominant role. During the degradation process, the efficient promotion of cleavage events in lignin methoxy, β-O-4 bond, and benzene ring was observed. Consequently, the depolymerization process led to the generation of high-value compounds, namely p-hydroxybenzaldehyde and vanillin. Remarkably, the yields of the high-value compounds in the synergistic photocatalytic system were five times larger than those in the control. This study offered a viable method to activate persulfate for alkali lignin degradation and to achieve a mutually beneficial strategy for wastewater treatment and recycling., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Endocrine-disrupting chemicals (EDCs) are widespread pollutants known to interfere with hormonal pathways and to disrupt behaviours. Standardised behavioural procedures have been developed in common fish model species to assess the impact of various pollutants on behaviours such as locomotor activity and anxiety-like as well as social behaviours. These procedures need now to be adapted to improve our knowledge on the behavioural effects of EDCs on less studied marine species. In this context, the European sea bass (Dicentrarchus labrax) is emerging as a valuable species representative of the European marine environment. Here, we designed and validated a two-step procedure allowing to sequentially assess anxiety-like behaviours (novel tank test) and social preference (visual social preference test) in sea bass. Thereafter, using this procedure, we evaluated whether social behavioural disruption occurs in 2-month-old larvae after an 8-day exposure to a xenoestrogen, the 17α-ethinylestradiol (EE2 at 0.5 and 50 nM). Our results confirmed previous studies showing that exposure to 50 nM of EE2 induces a significant increase in anxiety-like behaviours in sea bass larvae. On the contrary, social preference seemed unaffected whatever the EE2 concentration, suggesting that social behaviour has more complex mechanical regulations than anxiety., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

To realize the resource utilization of solid waste (coal slime) and further the dual carbon goals, utilizing coal slime and coal ash as adsorbates for CO 2 capture is crucial. This study employed low-temperature N 2 adsorption, low-pressure CO 2 adsorption, X-ray diffraction, X-ray fluorescence, and isothermal adsorption tests to assess coal slime and coal ash's pore/mineral composition characteristics. Subsequently, the influence on CO 2 adsorption was analyzed to reveal the CO 2 adsorption mechanisms of pores and clay minerals, and CO 2 molecule adsorption behavior. The results showed that: (1) ashing led to reductions in total pore volume, specific surface area, micropore volume, and micropore specific surface area, accompanied by substantial decreases in micropores and mesopores; (2) ashing generated high-temperature stable mineral species, including quartz, andalusite, hematite, and gypsum, while all calcite decomposed into CaO; (3) coal slime exhibited greater CO 2 adsorption capacity than coal ash, influenced by pore structure and clay minerals; (4) the adsorption behavior of coal slime and coal ash likely aligns with micropore filling theory, suggesting CO 2 is adsorbed within the 0.30-1.47 nm pore structure. This research contributes to optimizing coal by-product utilization in mining areas and exploring adsorbate materials for CO 2 sequestration in abandoned goaf., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Hydrocarbons are routinely detected at low concentrations, despite the degrading metabolic potential of ubiquitous microorganisms. The potential drivers of hydrocarbons persistence are lower bioavailability and mass transfer limitation. Recently, bioremediation strategies have developed rapidly, but still, the solution is not resilient. Biosurfactants, known to increase bioavailability and augment biodegradation, are tightly linked to bacterial surface motility and chemotaxis, while chemotaxis help bacteria to locate aromatic compounds and increase the mass transfer. Harassing the biosurfactant production and chemotaxis properties of degrading microorganisms could be a possible approach for the complete degradation of hydrocarbons. This review provides an overview of interplay between biosurfactants and chemotaxis in bioremediation. Besides, we discuss the chemical surfactants and biosurfactant-mediated biodegradation by microbial consortium., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Oil spills into the oceans cause irreparable damage to marine life and harms the coastal population of the affected areas. The main measures to be taken in response to an oil spill are to reduce the impact on marine life, prevent oil from reaching the shore through its recovery, and accelerate the degradation of unrecovered oil. Any environmental damage can be reduced if the spilled oil is removed from the water quickly and efficiently. Therefore, it is essential to know the treatment strategies for spilled oils. Several technologies are currently available, including booms, skimmers, in situ burning, use of adsorbents, dispersants/surfactants, and bioremediation. The selection of the type of treatment will depend not only on the effectiveness of the technique, but mainly on the type of oil, amount spilled, location, weather, and sea conditions. In this review, the characteristics of oil spills, their origin, destination, and impacts caused, including major accidents around the world, are initially addressed. Then, the main physical, chemical, and biological treatment technologies are presented, describing their advances, advantages, and drawbacks, with a focus on the use of green surfactants. These agents will be described in detail, showing the evolution of research, recent studies, patents, and commercialized products. Finally, the challenges that remain due to spills, the necessary actions, and the prospects for the development of existing treatment technologies are discussed, which must be linked to the use of combined techniques., (© 2022. The Author(s), under exclusive licence to Springer Nature Switzerland AG.)