Search

A synergistic photocatalytic system based on Fe-based perovskite with persulfate was constructed for alkali lignin (AL) degradation in pulp and paper wastewater. The degradation performance and mechanism on AL were carried out under ambient temperature and pressure, accompanied by visible light irradiation. The results showed that the synergistic photocatalytic system exhibited much better performance on AL degradation than the single catalytic system. The degradation efficiency reached 73.5% under the optimal conditions and was constant at around 65% over the pH range from 2 to 8. A significant escalation of the AL degradation was observed at pH 10, reaching 80.1%. The photogenerated holes, 1 O 2 and SO 4 - ·, generated by the system were involved in the degradation, and the holes played a dominant role. During the degradation process, the efficient promotion of cleavage events in lignin methoxy, β-O-4 bond, and benzene ring was observed. Consequently, the depolymerization process led to the generation of high-value compounds, namely p-hydroxybenzaldehyde and vanillin. Remarkably, the yields of the high-value compounds in the synergistic photocatalytic system were five times larger than those in the control. This study offered a viable method to activate persulfate for alkali lignin degradation and to achieve a mutually beneficial strategy for wastewater treatment and recycling., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Green liquor dregs (GLD) is an alkaline by-product from the pulp and paper industry with a pH between 10 and 14. Today most of the produced GLD in Sweden is landfilled. As a fine-grained alkaline material, it might be possible to use it for acid-generating mining waste remediation. To increase the utilization, quality characteristics and environmental performance need to be determined. In this study samples were collected 5 times from 16 mills during a period of 2.5 years, and were characterized by analyzing dry matter content, loss on ignition (LOI) 550 °C and LOI 950 °C, elemental analysis, pH, electrical conductivity, and calorific value. The results were then evaluated using multivariate statistics (PCA) as well as being compared to other studies and Swedish till. The results show that even if GLD is heterogenous (both within a mill and between different mills) trends can be seen for samples from most mills. When samples do stand out, it is predominately related to the same four mills. Most of the studied parameters showed characteristics favorable for use as a remediant; however, TOC, sulfur, and some of the elements require further study. In general, this study concludes that GLD can be a viable option for the remediation of small orphaned sulfidic mining sites and thus worthy of further studies on the interaction between GLD and acidic mining waste.Overall, GLD can be a good alternative for cost-effective remediation of smaller orphaned mining sites. It is readily available in large quantities, has the qualities needed for remediation of many orphaned acidic mining sites, and can often be locally sourced near the mining site. The use of GLD for mining site remediation is likely also a more sustainable method compared to traditional remediation methods., (© 2024. The Author(s).)

Paper mill sludge (PMS) is featured with a high content of cellulose and hemicellulose, and using its characteristics to make paperboard can achieve a high-value utilization of PMS, which has attracted growing interest. In this study, currently prevalent landfill, incineration technologies (generating heat and electricity by incineration), and three paperboard technologies (medium density fiberboard, pulp board, and corrugated paper) were evaluated and compared via life cycle assessment (LCA) and life cycle costing (LCC) methods. LCA results show that the PMS-to-pulp board outperforms others with an energy conservation and emission reduction (ECER) value of - 2.86 × 10 -8 , while the landfill exhibits the highest overall environmental impact with an ECER value of 4.80 × 10 -9 . LCC results reveal that the PMS-to-pulp board delivers the highest economic profit with $257.357, while the landfill is the lowest with $ - 35.63. The PMS paperboard technologies are more economically friendly than the incineration technologies due to additional electricity/steam consumption during the PMS pre-drying process in incineration. In addition, different scenarios were set up to explore national GHG emission reduction potential by increasing paperboard technologies application rate and reducing the proportion of landfill and incineration. The scenario analysis suggests that replacing 90% of landfill and incineration ratio with PMS paperboard technologies could tremendously improve the overall emission reduction performance with - 9.08 × 10 10 kg CO 2 eq. This result indicates that the PMS treatment technology transformation has a significant favorable impact on the achievement of the "carbon neutrality" target., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

To overcome the human and animal survivability risk, sustainable development is the only option on earth that can be achieved through the maximum use of renewable environmental resources. Recycling of waste paper is an emerging waste management approach to conserve natural resources. Herein, we studied enzyme-mediated process to recycle the xerographic paper by using the crude fungal extract from indigenously isolated fungi identified as Aspergillus assiutensis. The fungal enzyme cocktail has been characterized for the production of multiple enzymes namely cellulase, amylase, xylanase, pectinase, and protease. All these enzymes have pH optima in the acidic range and except cellulase and all the enzymes are stable from 10 to 80 C. In the zymogram analysis, pectinase, xylanase, amylase, and cellulase were detected at 68 kDa, ~ 54 kDa, 38 kDa, and 30 kDa, respectively. Also, the presence of protease was confirmed by the clear zone at 68, 31, and 16 kDa. A 26% decrease in the kappa number and reduction in Hex A of the pulp was observed on the treatment of the pulp with enzyme as compared to the control pulp without any treatment. The physical and chemical properties of the pulp were also improved by enzyme-mediated pulping as compared to the control The physiochemical parameter of the effluent like TDS was reduced (397 ppm) significantly in comparison to chemical deinking process and it was within the permissible limit. BOD and alkalinity were reduced when the enzymes and chemical dosage were used in combination. These results indicate that chemi-enzymatic deinking is most promising to reduce or remove the pollution parameters including ink and this approach can be used in the paper and pulp industry for sustainable development., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Neonicotinoid insecticides are used against agricultural, forest, and urban insect pests. Evaluation of dry neonicotinoid residues on treated filter paper is a commonly used method to determine the toxicity of active ingredients towards target and non-target organisms. Dry residues of four neonicotinoids, acetamiprid, dinotefuran, imidacloprid, and thiamethoxam, on filter paper did not cause significant levels of mortality in Hippodamia convergens (Guérin-Méneville) (Coleoptera: Coccinellidae) and Nezara viridula (L.) (Hemiptera: Pentatomidae) when compared to paired untreated groups. Conversely, nearly 100% mortality was observed when test insects were exposed to dry neonicotinoid residues on leaf discs and glass plate surfaces. On the other hand, dry residues of the pyrethroid bifenthrin on filter paper, leaf disks, and glass plates killed significantly more test insects when compared to untreated groups. Additional bioassays tested the toxicity of acetamiprid and thiamethoxam by evaluating the toxicity of dry residues on (1) the upper and (2) lower surfaces of treated filter paper, (3) on a glass plate underneath treated filter paper, (4) on the upper surface of treated filter paper treated with insecticide and adjuvant, and (5) dried residues on a glass plate after dipping treated filter paper in water and letting the solvent dry on the inert test surface. The results indicated that neonicotinoid insecticides applied to filter paper were adsorbed. Toxic compounds possibly move in between and binding to paper fibers so that no toxic residues were left on treated surfaces. However, adsorbed insecticides were still biologically active when washed out of filter paper and dried on an inert glass surface. The results reported here clearly demonstrate that the toxicity of neonicotinoid insecticides should not be evaluated using filter paper as a test surface., (© 2024. Sociedade Entomológica do Brasil.)

To ensure the safety of food contact materials, a liquid chromatography method was established to determine the migration of formaldehyde in paper packaging with various food simulants (10%, 25%, 50%, 75%, and 95% ethanol by volume) and to investigate the migration behavior of formaldehyde after various durations and with various materials. The results showed that the method has good linearity with a correlation coefficient of R 2  > 0.9990, a detection limit of 0.0011 ~ 0.0027 mg L -1 , and a spiked recovery of 89.7 ~ 103.2% in the range of formaldehyde determination; the migration of formaldehyde in all six paper contact materials showed a trend of gradual increase with time until equilibrium was reached. At the same time and temperature, the migration of formaldehyde in paper packaging was the highest in low-concentration ethanol. With the same food simulants and materials, the maximum migration of formaldehyde in printed materials was greater than that in nonprinted materials; with different materials and the same food simulant, the thickness value was higher, with the use of water-based ink as a printing material, and the maximum migration value of formaldehyde by offset printing technology was low., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Globally, per- and polyfluoroalkyl substances (PFAS)-related research on paper products has focused on food packaging with less consideration on the presence of PFAS at different stages of the paper recycling chain. This study analysed the prevalence of PFAS in paper grades used for the manufacture of recycled paperboard. The presence of PFAS was attributed to the use of PFAS-containing additives, consumer usage, exposure to packed goods as well as contamination during mingling, sorting, collection, and recovery of paper recycling material. Q Orbitrap mass spectrometry was used to analyse the paper samples after accelerated solvent extraction and solid phase extraction. The distribution and possible propagation of 22 PFAS were determined in pre-consumer, retail and post-consumer paper products. Post-consumer samples had the highest combined average concentration (ΣPFAS) at 213 ng/g, while the ΣPFAS in retail (159 ng/g) and pre-consumer samples (121 ng/g) was detected at lower concentrations. This study showed that waste collection and recycling protocols may influence PFAS propagation and that measures must be developed to minimise and possibly eliminate exposure opportunities., (© 2024. The Author(s).)

Abstract Renewable materials and material circularity are key priorities for the coming decades. While paper is the most utilized material in the packaging sector, its applications in food packaging are limited due to low barrier properties. Coating it with petroleum-based polymer barrier coatings renders it unrecyclable both mechanically and biologically. Bio-coated paper packaging, made from agricultural waste or by-products, presents environmentally favorable solutions that can benefit the biological cycle of the circular economy. The main objective of this study is to assess the applicability of grain and beer production by-products in wood pulp food packaging materials. It examines the effects of different grain by-products (industrial wheat grain processing residues and wheat bran) particles and concentrations (15 wt% and 40 wt%), as well as the impact of brewer’s yeast (Saccharomyces cerevisiae) at a concentration of 10 wt%, on the physical–mechanical and barrier properties of Northern bleached softwood kraft (NBSK) and chemithermomechanical (CTMP) pulps. Material composites were fabricated using a standard sheet forming method. Physical–mechanical properties were analyzed through tensile strength, strain at break, tear resistance, and bending stiffness tests. Barrier-related properties were analyzed through roughness, air permeance, and water contact angle tests. Results revealed that the vast majority of physical–mechanical properties decreased with the increase of both types of grain production fillers. Industrial wheat grain processing residues had a lower impact on physical–mechanical properties than wheat bran filler. A higher percentage of property decrease was absorbed in NBSK pulp than in CTMP. Roughness of CTMP can be improved by adding both industrial wheat grain processing residues and wheat bran. Wheat bran particles can increase hydrophobicity. CTMP pulp strength properties can be increased with the addition of yeast; however, the yeast additive’s effect on air permeance demonstrated a negative impact. In the case of NBSK pulp, which has higher primary strength properties, the addition of yeast does not make any significant changes. The conducted experiments demonstrated that, overall, the addition of these fillers resulted in a decline in physical–mechanical properties such as tensile strength, strain at break, tear resistance, and bending stiffness. This decline was more pronounced with higher concentrations of fillers. In the case of CTMP pulp, both types of fillers exhibited similar trends in affecting properties, whereas for NBSK pulp, wheat bran had a more significant impact compared to wheat grain processing residues. The addition of yeast generally led to a reduction in physical–mechanical properties, particularly in tensile strength and tear resistance. However, samples containing yeast displayed increased flexibility compared to controls. The influence on barrier properties varied: while yeast increased air permeability, it also enhanced surface hydrophobicity, thereby reducing the paper’s receptivity to liquids.

China's pulp and paper industry (CPPI) has been always the main carbon emission source in recent years. However, the analysis on influencing factors of carbon emissions from this industry is insufficient. To address the issue, the CO 2 emissions from CPPI are estimated in the period of 2005-2019, the driving factors of CO 2 emissions are investigated by the logarithmic mean Divisia index (LMDI) method, the decoupling state of economic growth and CO 2 emissions is determined by Tapio decoupling model, and finally, future CO 2 emissions are predicted under four scenarios by the STIRPAT model to explore the potential of carbon peaking. The results show that CPPI exhibits a rapid increase and a fluctuating downward trend in CO 2 emissions during the period of 2005-2013 and 2014-2019, respectively. The main promoting and inhibiting factors to the increase of CO 2 emission are per capita industrial output value and energy intensity, respectively. There are five decoupling states of CO 2 emissions and economic growth during the study period, and the CO 2 emissions exhibit a weak decoupling state with the industrial output value growth in most years of the study period. It is very difficult to realize the carbon peaking goal by 2030 under the baseline and fast development scenarios. Therefore, efficient low carbon and strong low-carbon development policies are necessary and urgent for the realization of carbon peaking goal and the sustainable development of CPPI., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

The production of paper is a key component for global civilization. Around 300 million tonnes of paper are produced every day globally, with matured pulpwood being the major contributor. Due to rising demand for paper and the depletion of available wood resources, researchers are now focused on finding alternative non-wood resources that are suitable for pulp and paper production. The current study aims to produce eco-friendly and biodegradable paper using a combination of Eichhornia crassipes (water hyacinth) and dried flowers. Water hyacinth is considered as a lignocellulose plant which contains 57% lignocellulose, and dried flower contains 40% cellulose, which is the prime source for paper production. Various sections of water hyacinth, including wet and dry petiole, leaves, and root, were blended with dried flowers through the soda process. Then, the physical properties and FTIR analysis was carried out to identify the quality of the paper produced. The paper produced from root and dried petiole has a lower thickness (1.0 mm and 0.5 mm) than other mix proportions. The opacity of the leaves was found to be 0.5% (light passing) and for the root 0.7% (light passing). Also, the dry petiole and root paper have a good dry tensile strength of 1.30Kpa and 1.20Kpa, respectively. Hence, paper made from dry petiole and root was found to be efficient and suitable for the paper industry., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

The economic development of a country directly depends upon industries. But this economic development should not be at the cost of our natural environment. A substantial amount of water is spent during paper production, creating water scarcity and generating wastewater. Therefore, the Pollution Control Board classifies this industry into red category. Water is used in different papermaking stages such as debarking, pulping or bleaching, washing, and finishing. The wastewater thus generated contains lignin and xenobiotic compounds such as resin acids, chlorinated lignin, phenols, furans, dioxins, chlorophenols, adsorbable organic halogens (AOX), extractable organic halogens (EOCs), polychlorinated biphenyls, plasticizers, and polychlorinated dibenzodioxins. Nowadays, several microorganisms are used in the detoxification of these hazardous effluents. Researchers have found that microbial degradation is the most promising treatment method to remove high biological oxygen demand (BOD) and chemical oxygen demand (COD) from wastewater. Microorganisms also remove AOX toxicity, chlorinated compounds, suspended solids, color, lignin, derivatives, etc. from the pulp and paper mill effluents. But in the current scenario, mill effluents are known to deteriorate the environment and therefore it is highly desirable to deploy advanced technologies for effluent treatment. This review summarizes the eco-friendly advanced treatment technologies for effluents generated from pulp and paper mills., (© 2024. The Author(s), under exclusive licence to Springer Nature Switzerland AG.)

Abstract Large language models (LLMs) are an exciting breakthrough in the rapidly growing field of artificial intelligence (AI), offering unparalleled potential in a variety of application domains such as finance, business, healthcare, cybersecurity, and so on. However, concerns regarding their trustworthiness and ethical implications have become increasingly prominent as these models are considered black-box and continue to progress. This position paper explores the potentiality of LLM from diverse perspectives as well as the associated risk factors with awareness. Towards this, we highlight not only the technical challenges but also the ethical implications and societal impacts associated with LLM deployment emphasizing fairness, transparency, explainability, trust and accountability. We conclude this paper by summarizing potential research scopes with direction. Overall, the purpose of this position paper is to contribute to the ongoing discussion of LLM potentiality and awareness from the perspective of trustworthiness and responsibility in AI.

Imported waste paper and recycled pulp may contain pollutants, posing potential environmental risks to the ecosystem of China. This study examined the presence and distribution patterns of heavy metals, phthalate esters (PAEs), and adsorbable organic halogens (AOX) in recycled pulp and production wastewater after various recycling processes of three typical restricted types of imported waste paper. The results indicated that the concentration ranges of heavy metals, PAEs, and AOX in the three types of imported recycled waste paper were 21.61-40.38 mg/kg, 15.35-27.88 mg/kg, and 19.21-57.72 mg/kg, respectively. The comparative analysis with the initial waste paper demonstrated a reduction in heavy metal content in the recycled pulp by 17.80-49.75%, PAEs by 65.42-90.55%, and AOX by 32.80-42.34%. The average concentrations of these pollutants in wastewater were 0.85-1.66 mg/L, 27.28-59.86 mg/L, and 1.15-3.34 mg/L, respectively. Chromium and lead were identified as the primary heavy metals present in the waste paper. Following pulping, No. 1 and No. 2 met the arsenic and lead levels specified in the "Reuse Fiber Pulp" standard (GB/T24320-2021), whereas No. 3 met these criteria after de-inking only. The main PAEs detected in the waste paper were dibutyl phthalate and di(2-ethylhexyl) phthalate, most of which were removed during the pulping stage. Significantly higher levels of AOX were observed in No. 2 and No. 3 than in No. 1, with a minimal impact on AOX removal from the pulp during the recycling process., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Paediatric Intensive Care Units (PICU) are complex interdisciplinary environments where challenging, high stakes decisions are frequently encountered. We assert that appropriate decisions are more likely to be made if the decision-making process is comprehensive, reasoned, and grounded in thoughtful deliberation. Strategies to overcome barriers to high quality decision-making including, cognitive and implicit bias, group think, inadequate information gathering, and poor quality deliberation should be incorporated. Several general frameworks for decision-making exist, but specific guidance is scarce. In this paper, we provide specific guidance on collaborative complex decision-making for PICUs. The proposed approach is on principles of procedural justice and pragmatic hermeneutics. The process encompasses set-up/planning, information gathering, question formulation, analysis (perspectives, values, and principles), action plan development, decision documentation, and a review and appeal mechanism. The process can be adapted to suit other clinical contexts. Research evaluating the process, exploring how best to develop education for clinicians, and how to build a culture that values high quality deliberation, is worthwhile., (© 2024. Journal of Bioethical Inquiry Pty Ltd.)

Objective: Although point of care ultrasound (POCUS) use has become prevalent in medicine, clinicians may not be familiar with the evidence supporting its utility in patient care. The objective of this study is to identify the top five most influential papers published on the use of cardiac POCUS and lung POCUS in adult patients., Methods: A 14-member expert panel from the Canadian Association of Emergency Physicians (CAEP) Emergency Ultrasound Committee and the Canadian Ultrasound Fellowship Collaborative used a modified Delphi process. Panel members are ultrasound fellowship trained or equivalent, are engaged in POCUS scholarship, and are leaders in POCUS locally and nationally in Canada. The modified Delphi process consisted of three rounds of sequential surveys and discussion to achieve consensus on the top five most influential papers on cardiac POCUS and lung POCUS., Results: A total of 66 relevant papers on cardiac POCUS and 68 relevant papers on lung POCUS were nominated by the panel. There was 100% participation by the panel members in all three rounds of the modified Delphi process. At the end of this process, we identified the top five most influential papers on cardiac POCUS and lung POCUS. Papers include studies supporting the use of POCUS for accurately assessing left ventricular systolic function, diagnosing pericardial effusion, clarifying its test characteristics for pulmonary embolism, identifying pulmonary edema and pneumonia, as well as consensus statements on the use of cardiac and lung POCUS in clinical practice., Conclusion: We have created a list of the top five influential papers on cardiac POCUS and lung POCUS as an evidence-based resource for trainees, clinicians, and researchers. This will help trainees and clinicians better understand how to use POCUS when scanning the heart and lungs, and it will also help researchers better understand where to direct their scholarly efforts with future research., (© 2024. The Author(s), under exclusive licence to the Canadian Association of Emergency Physicians (CAEP)/ Association Canadienne de Médecine d'Urgence (ACMU).)

Cerebellum is a key-structure for the modulation of motor, cognitive, social and affective functions, contributing to automatic behaviours through interactions with the cerebral cortex, basal ganglia and spinal cord. The predictive mechanisms used by the cerebellum cover not only sensorimotor functions but also reward-related tasks. Cerebellar circuits appear to encode temporal difference error and reward prediction error. From a chemical standpoint, cerebellar catecholamines modulate the rate of cerebellar-based cognitive learning, and mediate cerebellar contributions during complex behaviours. Reward processing and its associated emotions are tuned by the cerebellum which operates as a controller of adaptive homeostatic processes based on interoceptive and exteroceptive inputs. Lobules VI-VII/areas of the vermis are candidate regions for the cortico-subcortical signaling pathways associated with loss aversion and reward sensitivity, together with other nodes of the limbic circuitry. There is growing evidence that the cerebellum works as a hub of regional dysconnectivity across all mood states and that mental disorders involve the cerebellar circuitry, including mood and addiction disorders, and impaired eating behaviors where the cerebellum might be involved in longer time scales of prediction as compared to motor operations. Cerebellar patients exhibit aberrant social behaviour, showing aberrant impulsivity/compulsivity. The cerebellum is a master-piece of reward mechanisms, together with the striatum, ventral tegmental area (VTA) and prefrontal cortex (PFC). Critically, studies on reward processing reinforce our view that a fundamental role of the cerebellum is to construct internal models, perform predictions on the impact of future behaviour and compare what is predicted and what actually occurs., (© 2024. The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.)

Abstract Autistic individuals often experience a wide range of barriers and challenges with employment across their lifetime. Despite their strengths and abilities to contribute to the workforce, many individuals experience unemployment, underemployment and malemployment. However, current supports and services are often inadequate to meet their needs. To allow autistic people to achieve vocational success, we explore four contributors to employment and expand upon the issues and potential solutions to each. These positions include the importance of family support and its consideration in the application of vocational support interventions, addressing transitional needs for autistic youth, building employer capacity, and conducting research that advises the development of meaningful programs and policies. By advocating for these positions, we aim to foster greater inclusivity and support for individuals with ASD in the workplace.

Nowadays, the paper industry supplies its required fibers either from primary fibers, including wood and plants, or waste papers, called secondary fibers. One of the most challenging recycling processes is deinking of papers digitally printed with electrophotographic ink. In order to produce optically high-quality paper from recycled waste papers, deinking step is required at the desired levels. In this work, the environmentally friendly green enzymatic deinking of printed paper was modeled and optimized via an innovative approach called artificial intelligence method. The effect of treatment temperature, treatment time, and enzyme dosage on mechanical properties (tensile and burst strengths) as well as optical properties (whiteness and brightness) of handsheet was investigated. The developed code can appropriately learn the non-linear behavior of deinking process, and make decisions according to the pattern constructed intelligently. Finally, multi-objective optimization at the specified treatment temperature, treatment time, and enzyme dosage was performed to identify the best conditions for enzyme-deinked handsheet (maximized mechanical and optical properties)., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

A simple one-step drawing for the cost-effective fabrication of microfluidic paper-based analytical devices (µPADs) for the determination of phosphate content in water and fertilizer samples is presented in this paper. The hydrophobic barrier of µPAD was patterned using a 2-mm tip marker pen using a transparent acrylic sheet template. The molybdenum blue reaction using ascorbic acid as a reducing agent was used. A pre-concentration step of samples is proposed to improve the sensitivity of the measurement. The blue complex produced on the µPADs was recorded using a smartphone camera. The color intensities (red, green, blue and gray) were analyzed using ImageJ program. The proposed µPAD method provides a linear calibration range from 0 to 100 mg L -1 P. The limit of detection (LOD) was found to be 0.7 mg L -1 P with a precision of 3.1%RSD for 50 mg L -1 P (n = 10). The proposed method was successfully applied to the determination of phosphorus contents in water and liquid chemical fertilizer samples. The results obtained from µPAD agreed with a spectrophotometric method using paired t test at a 95% confidence level., (© 2022. The Author(s), under exclusive licence to The Japan Society for Analytical Chemistry.)

Abstract Students often recruit digital devices to complete their classroom activities. To determine best practices for the classroom, the present study explored the use of tablets relative to laptops and paper in the understudied context of brief, in-person, small group academic tasks. One-hundred twenty small groups of two to three undergraduate students were randomly assigned to one device (paper, laptop, or tablet) and one set-up (a single shared device or multiple individual devices) in a 3 × 2 between-subjects design. Data were collected in 2019 –2021. Students completed one group task that culminated in a knowledge quiz and a second group task that culminated in writing their own quiz together. They then individually rated group members as well as reported their perceptions of satisfaction, effort, and difficulty. Open-ended questions further assessed their perceptions of technology and the three devices in question. Results showed equivalency in group outcomes and individual perceptions across devices and set-ups, with very few exceptions. Quantitative and qualitative data supported that students found advantages and drawbacks to each device and believed that all were effective tools in such a context. Educators must consider the affordances of different technologies when encouraging their use in the classroom but should be open to students using their device of choice for groupwork.

Concerns about human health regarding the large use of bisphenol A in thermal papers have led to its replacement by bisphenol S. Analyses of bisphenols require several sample pretreatment steps, which are laborious, expensive, and time-consuming. A paper spray ionization mass spectrometry (PSI-MS) was developed to detect and quantify bisphenol S in three different brands of thermal papers commercially available. Parameters such as paper size, and paper position relative to the mass spectrometer inlet were evaluated. The analyses were performed in selected ion monitoring mode on a linear ion trap mass spectrometer. The developed method presented absolute recovery values ranging from 92.2 to 109.04%, accuracy values from -1.2 to 9.0%, and inter assay precision from 1.8 to 5.6% and enabled LOD as low as 5 ng g -1 . The concentration of bisphenol S in all of the three brands of BPA-free thermal papers evaluated ranged from 1.36 to 6.77 μg g -1 , and the concentrarion of BPA ranged from 6.56 to 16.4 μg g -1 in all samples of thermal paper evaluated. The PSI-MS method described here was comparable to the conventional ones, such as liquid chromatography coupled with mass spectrometry and gas chromatography coupled with mass spectrometry described in the literature. The present study proved to be practical, fast, and efficient for the direct determination of bisphenol S in thermal papers. Furthermore, the methodology here described showed to be a promising alternative to replace the classical methods for determination of bisphenol S, due to its simplicity, and no needing of any sample pretreatment., (© 2021. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)