Search

The delayed healing of chronic wounds, such as diabetic foot ulcers (DFUs), is a clinical problem. Few dressings can promote wound healing by satisfying the demands of chronic wound exudate management and tissue granulation. Therefore, the aim of this study was to prepare a high-absorption polyurethane (PU) foam dressing modified by polyethylene glycol (PEG) and triethoxysilane (APTES) to promote wound healing. PEG-modified (PUE) and PEG/APTES-modified (PUESi) dressings were prepared by self-foaming reactions. Gauze and PolyMem were used as controls. Next, Fourier transform-infrared spectroscopy, thermomechanical analyses, scanning electron microscopy and tensile strength, water absorption, anti-protein absorption, surface dryness and biocompatibility tests were performed for in vitro characterization. Wound healing effects were further investigated in nondiabetic (non-DM) and diabetes mellitus (DM) rat models. The PUE and PUESi groups exhibited better physicochemical properties than the gauze and PolyMem groups. Moreover, PUESi dressing showed better anti-adhesion properties and absorption capacity with deformation. Furthermore, the PUESi dressing shortened the inflammatory phase and enhanced collagen deposition in both the non-DM and DM animal models. To conclude, the PUESi dressing not only was fabricated with a simple and effective strategy but also enhanced wound healing via micronegative-pressure generation by its high absorption compacity with deformation.

To improve the water absorbency and water-retention rate of superabsorbent materials, a porous calcium carbonate composite superabsorbent polymer (PCC/PAA) was prepared by copolymerization of acrylic acid and porous calcium carbonate prepared from ground calcium carbonate. The results showed that the binding energies of C–O and C=O in the O 1s profile of PCC/PAA had 0.2 eV and 0.1–0.7 eV redshifts, respectively, and the bonding of –COO− groups on the surface of the porous calcium carbonate led to an increase in the binding energy of O 1s. Furthermore, the porous calcium carbonate chelates with the –COO− group in acrylic acid through the surface Ca2+ site to form multidirectional crosslinking points, which would increase the flexibility of the crosslinking network and promote the formation of pores inside the PCC/PAA to improve the water storage space. The water absorbency of PCC/PAA with 2 wt% porous calcium carbonate in deionized water and 0.9 wt% NaCl water solution increased from 540 g/g and 60 g/g to 935 g/g and 80 g/g, respectively. In addition, since the chemical crosslinker N,N′-methylene bisacrylamide is used in the polymerization process of PCC/PAA, N,N′-methylene bisacrylamide and porous calcium carbonate enhance the stability of the PCC/PAA crosslinking network by double-crosslinking with a polyacrylic acid chain, resulting in the crosslinking network of PCC/PAA not being destroyed after water absorption saturation. Therefore, PCC/PAA with 2 wt% porous calcium carbonate improved the water-retention rate by 244% after 5 h at 60 °C, and the compressive strength was approximately five-times that of the superabsorbent without porous calcium carbonate. [ABSTRACT FROM AUTHOR]

A superabsorbent polymer (SAP) was synthesized by copolymerizing itaconic acid and vinyl sulfonic acid. The typically low absorbency of itaconic acid-based SAPs under mechanical loads was improved by introducing surface crosslinking. Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy were used to characterize the synthesis and surface-crosslinking reactions in the SAP. Various conditions for surface-crosslinking reactions, such as the surface-crosslinking solution, content of surface-crosslinking agent, and reaction temperature, were explored and correlated with the gel strength and absorption characteristics of the resulting SAP particles. The distilled water content in the surface-crosslinking solution strongly influenced the absorption capacity of the SAP, but this sensitivity decreased when acetone was used as a co-solvent. Itaconic acid-based SAP that was crosslinked under optimal conditions exhibited centrifuge retention capacity and absorbency under a load of 31.1 and 20.2, respectively.

In this article, the second method of determination of the theoretical and actual working volume of a hydraulic motor is described. The proposed new method is based on the characteristics of effective absorbency of the motor. The effective absorbency has been defined as the ratio of flow rate in a motor to the rotational speed of the motor's shaft. It has been shown that the effective absorbency is a nonlinear function of the rotational speed and nonlinear function of the pressure drop in the motor's working chambers. Furthermore, it has been proven that the actual working volume of a motor is a function of a third degree of pressure drop in the motor's working chamber. The actual working volume should be taken to assess the mechanical and volumetric energy losses in the motor. Furthermore, the influence of the flowmeter location in the measurement system and the compressibility of liquid on the result of the theoretical and actual working volume calculation was also taken into account and is described in this article. The differences in the assessment of the volumetric efficiency assuming the theoretical and actual working volume was also shown. [ABSTRACT FROM AUTHOR]

The swelling behaviors and water retention of superabsorbent sand-fixing materials prepared from acrylic acid/acrylamide copolymer (AA/AM) and acid-modified attapulgite under ultrasonic treatments and different pH conditions were investigated. The results demonstrated that a suitable amount of attapulgite can effectively improve the absorption capacity and saltwater performance. The superabsorbent achieved the highest absorptions of 1257.54 g/g and 209.45 g/g in distilled water and a 0.9 wt% NaCl solution, and a higher water absorbency occurred over a wide pH range of 5~9 when the ultrasonic power was 200 W and the attapulgite content was 10%. The addition of attapulgite could significantly increase the water absorption and retention. [ABSTRACT FROM AUTHOR]

Military personnel are exposed to several harsh conditions and mosquitos in mountains and wild forests. Mosquito-repellent textiles can help them to cope with such conditions. The present research work established a sustainable approach for fabricating microcapsules from Eucalyptus oil, Moringa oleifera, and Arabic gum via a complex coacervation method. Moringa oleifera and Arabic gums were utilized as the outer shell of the microcapsules, whereas the core part was made of Eucalyptus oil in different concentrations. The military camouflage-printed polyester/cotton (PC) blended fabric was coated with the as-prepared microcapsules using the pad–dry–cure technique. The surface morphology of the microcapsules was examined using an optical microscope and scanning electron microscope (SEM), and the coated fabric's mosquito-repellent property was investigated using a specified cage test according to a standard testing protocol. The water absorbency and air permeability of the treated samples were also evaluated in order to learn about the comfort properties. The cage test results revealed that the coated fabric had a good tendency to repel the mosquitoes used in the cage test. In addition, the coated fabric showed significant durability even after several rigorous washing cycles. However, the application of microcapsules to the fabric slightly affected the water absorbency and air permeability of the fabric. This study presents a novel sustainable approach for fabricating microcapsules from the mentioned precursors and their application in the field of textiles, particularly for military purposes. [ABSTRACT FROM AUTHOR]

To synthesize a biodegradable alternative to spherical polyacrylic acid absorbent resin, spherical hydrogel particles were prepared from carboxymethyl cellulose (CMC) dissolved in an aqueous solution, using ethylene glycol diglycidyl ether (EGDE) as a crosslinking agent. The effect of varying the initial CMC concentration and feed amount of EGDE on the shape, water absorbency, water-holding capacity, and enzyme degradability of the resultant CMC hydrogels was determined. The reaction solution was poured into fluid paraffin, and spherical hydrogel particles were obtained via the shear force from stirring. The shape and diameter of the spherical hydrogel particles in the swollen state depended on the CMC concentration. The spherical hydrogel particles obtained by increasing the amount of EGDE resulted in a decrease in absorbency. Additionally, all the spherical hydrogel particles were degraded by cellulase. Thus, spherical biodegradable hydrogel particles were prepared from CMC, and the particle size and water absorption of the hydrogel could be controlled in the range of 5–18 mm and 30–90 g·g−1 in the swollen state, respectively. As an alternative to conventional superabsorbent polymers, the spherical CMC hydrogels are likely to be useful in industrial and agricultural applications. [ABSTRACT FROM AUTHOR]

Superabsorbent polymers (SAPs) are used as a soil amendment for retaining water, but suitable methods for the application of SAPs have not yet been developed. Here, we characterized a variety of soil–SAP mixtures prepared using four different types of SAP in terms of their water absorption and release characteristics. The teabag method was applied to characterize the soil–SAP mixtures, except for measurements of the matric potential. The results showed that the variations in water absorbency among the four SAPs in isolation became insignificant when they were mixed with sandy soils. The rates of water released from the soil–SAP mixtures under heated conditions were mitigated with decreasing water content, which prolonged the time until desiccation of the mixtures. The water absorbency of the SAPs significantly decreased in salt solutions (KCl and CaCl2), but their absorbency mostly recovered following immersion in tap water. The soil–dry SAP mixtures retained a larger amount of water than the soil–gel SAP mixtures. Swollen SAPs predominantly retained water in the range of −0.98 to −3.92 kPa, suggesting that SAP induces a transition from gravitational water to readily plant-available water by swelling itself. SAPs barely increased the amount of plant-available water in a potential range of −3.92 to −98.1 kPa, but significantly increased the soil water at <−98.1 kPa. The soil water content increased with an increasing SAP application rate, whereas the proportion of plant-available water declined. Our findings indicated that the performance of SAPs depends on the pore space and a saline environment in the soil and that low SAP application rates are suitable for maximizing the water available to plants in sandy soils. [ABSTRACT FROM AUTHOR]

Drought conditions after sowing threaten the seedling establishment of all seeds, including cover crops. Cover crops are commonly broadcast and, thus, are often susceptible to drought stress after sowing. Our hypothesis was that seed coating with superabsorbent polymers (SAPs) would enhance germination in the lab and stand establishment in the field by increasing water availability to single seeds. Red clover (Trifolium pratense L.) seeds were coated with the following selected SAP formulations at 2% of their seed weight: cross-linked potassium polyacrylate (PAL), cross-linked polyacrylamide-based polymer (PAM), PAM with graphite (PAM+G), and Starch-g-2-Propenoic acid (potassium salt) (STR). The water absorbency of each SAP formulation was >200 g water/g of polymer; STR had the greatest absorbency, at 352 g water/g of polymer. A seed coating method was developed, resulting in the uniform application of SAP from seed to seed. All SAP coating treatments increased germination compared to the 0% SAP coating in controlled environment studies in the lab. Three field trials were conducted for each seed coating treatment, providing a range of climatic soil conditions. Within each field trial, the STR with the greatest water absorbency had a higher stand for treatments sown by broadcasting followed by raking to incorporate seeds. The first two trials were conducted under more stressful conditions. PAM+G performed best in the first two trials by broadcasting seeds with no raking. Collectively, the selected SAP seed coating improved field stands compared to the non-treated controls. [ABSTRACT FROM AUTHOR]

Polyelectrolyte complex (PEC) hydrogel, formed via physically electrostatic crosslinks between polyanion and polycation, is an interesting hydrogel in terms of its nontoxicity and solvent-free technique. In this work, poly (sodium 4-styrenesulfonate) (PSS)/poly (diallyl dimethyl ammonium chloride) (PDADMAC) complex hydrogels were prepared. Firstly, the PSS/PDADMAC complex aggregates using various PSS/PDADMAC mole fractions that were prepared in the presence of NaCl solution. Then, the aggregates were resolubilized under stirring at 70 °C for 2 h to obtain a homogeneous PEC solution. Finally, the PEC solution was dialyzed using a dialysis membrane with 3500 molecular cut-off for 1 day. The dialysis bath was changed every interval period of 2 h to control the rate of reversible electrostatic interaction, resulting in the homogenous PEC hydrogel with porous morphology as revealed by SEM and BET investigations. The dimensional stability and viscoelasticity of the PEC hydrogel was studied by DMA experiment, which showed the viscoelastic behavior at a compressive force ranging from 0 to 0.1 N. Finally, PSS/PDADMAC hydrogels showed a high water absorbency property and excellent affinity to textile anionic dyes. [ABSTRACT FROM AUTHOR]

Drought and water shortage are serious problems in many arid and semi-arid regions. This problem is getting worse and even continues in temperate climatic regions due to climate change. To address this problem, the use of biodegradable hydrogels is increasingly important for the application as water-retaining additives in soil. Furthermore, efficient (micro-)nutrient supply can be provided by the use of tailored hydrogels. Biodegradable polyaspartic acid (PASP) hydrogels with different available (1,6-hexamethylene diamine (HMD) and L-lysine (LYS)) and newly developed crosslinkers based on diesters of glycine (GLY) and (di-)ethylene glycol (DEG and EG, respectively) were synthesized and characterized using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) and regarding their swelling properties (kinetic, absorbency under load (AUL)) as well as biodegradability of PASP hydrogel. Copper (II) and zinc (II), respectively, were loaded as micronutrients in two different approaches: in situ with crosslinking and subsequent loading of prepared hydrogels. The results showed successful syntheses of di-glycine-ester-based crosslinkers. Hydrogels with good water-absorbing properties were formed. Moreover, the developed crosslinking agents in combination with the specific reaction conditions resulted in higher water absorbency with increased crosslinker content used in synthesis (10% vs. 20%). The prepared hydrogels are candidates for water-storing soil additives due to the biodegradability of PASP, which is shown in an exemple. The incorporation of Cu(II) and Zn(II) ions can provide these micronutrients for plant growth. [ABSTRACT FROM AUTHOR]

Geopolymer is a promising porous material that can be used for evaporative cooling applications. Developing a greener geopolymer using agricultural and industrial wastes is a promising research area. In this study, we utilize rice husk (RH), rice husk ash (RHA), metakaolin (MK), ground granulated blast furnace slag (GGBS), and palm oil fuel ash (POFA) to prepare geopolymer pastes, with alkali liquid as an activator. Many geopolymer samples have been prepared as per the Design of Experimental software (DOE), and its corresponding response surface mode and central composite design and later they were characterized. The samples were cured in an oven for 2 h at 80 °C, and thereafter stored at room temperature (~25-30 °C) prior to being tested for its water absorption and compressive strength. The effect of the different composition of precursors on water absorption, density, porosity, and the compressive strength of the prepared geopolymers have been investigated. The results showed that the compressive strength of geopolymers is directly proportional to the ratio of the alkali liquid. Post-optimization, the best geopolymer paste mixture was confirmed to contain 10% of RH, 15% RHA, 35% MK, 10% POFA and 30% of GGBS, with 72% desirability for maximum water absorption (~38%) and compressive strength (4.9 MPa). The results confirmed its applicability for evaporative cooling. [ABSTRACT FROM AUTHOR]

To improve the salt resistance of superabsorbent materials and the gel strength of superabsorbent materials after water absorption, a bagasse cellulose-based network structure composite superabsorbent (CAAMC) was prepared via graft copolymerization of acrylamide/acrylic acid (AM/AA) onto bagasse cellulose using silane coupling agent modified nano-CaCO3 (MNC) and N,N′-methylene bisacrylamide (MBA) as a double crosslinker. The acrylamide/acrylic acid was chemically crosslinked with modified nano-CaCO3 by C-N, and a stable double crosslinked (DC) network CAAMC was formed under the joint crosslinking of N,N′-methylene bisacrylamide and modified nano-CaCO3. Modified nano-CaCO3 plays a dual role of crosslinking agent and the filler, and the gel strength of composite superabsorbent is two times higher than that of N,N′-methylene bisacrylamide single crosslinking. The maximum absorbency of CAAMC reached 712 g/g for deionized water and 72 g/g for 0.9 wt% NaCl solution. The adsorption process of CAAMC was simulated by materials studio, and the maximum adsorption energy of amino and carboxyl groups for water molecules is −2.413 kJ/mol and −2.240 kJ/mol, respectively. According to the results of CAAMC soil water retention, a small amount of CAAMC can greatly improve the soil water retention effect. [ABSTRACT FROM AUTHOR]

To prepare a novel cassava starch-based phosphorus releasing super-absorbent polymer (CST-PRP-SAP), the single factor and orthogonal experiment were applied to analyze the effects of different reaction conditions on the absorption and phosphorus release capacities of CST-PRP-SAP samples. The structural and morphological characteristics of the cassava starch (CST), powdered rock phosphate (PRP), cassava starch-based super-absorbent polymer (CST-SAP) and CST-PRP-SAP samples were all compared with various technologies, such as the Fourier transform infrared spectroscopy and X-ray diffraction pattern, etc. The results showed that the CST-PRP-SAP samples had good performances of water retention and phosphorus release which were synthesized, such as the reaction temperature, starch content, P2O5 content, crosslinking agent, initiator, neutralization degree, and acrylamide content, which were 60 °C, 20% w/w, 10% w/w, 0.02% w/w, 0.6% w/w, 70% w/w, and 15% w/w, respectively. The water absorbency of CST-PRP-SAP was almost larger than that of the CST-SAP sample with a P2O5 content of 5.0% and 7.5%, and they all gradually decreased after three consecutive water absorption cycles. The CST-PRP-SAP sample could maintain about 50% of the initial water content after 24 h, even at the temperature of 40 °C. The swelling process of CST-PRP-SAP conformed to the non-Fickian diffusion, which was determined by the diffusion of water molecules and the relaxation process of polymer chain segments. The cumulative phosphorus release amount and release rate of the CST-PRP-SAP samples were increased with the increasing PRP content and the decreasing neutralization degree. After a 216 h immersion, the cumulative phosphorus release amount and release rate of the CST-PRP-SAP samples with different PRP contents were increased by 17.4 and 3.7 times, respectively. The rough surface of the CST-PRP-SAP sample after swelling was beneficial to the performance of water absorption and phosphorus release. The crystallization degree of PRP in the CST-PRP-SAP system was decreased and most of the PRP existed in the form of physical filling, and the available phosphorus content was increased to a certain extent. It was concluded that the CST-PRP-SAP synthesized in this study has excellent properties of continuous water absorption and retention with functions of promotion and the slow-release phosphorus. [ABSTRACT FROM AUTHOR]

Plant fibers (PFs), such as hemp, Coir, and straw, are abundant in resources, low in price, light weight, biodegradable, have good adhesion to the matrix, and have a broad prospect as reinforcements. However, the degradation of PFs in the alkaline matrix is one of the main factors that affects the durability of these composites. PFs have good compatibility with cement and the geopolymer matrix. They can induce gel growth of cement-based materials and have a good toughening effect. The water absorption of the hollow structure of the PF can accelerate the degradation of the fiber on the one hand and serve as the inner curing fiber for the continuous hydration of the base material on the other. PF is easily deteriorated in the alkaline matrix, which has a negative effect on composites. The classification and properties of PFs, the bonding mechanism of the interface between PF reinforcements and the matrix, the water absorption of PF, and its compatibility with the matrix were summarized. The degradation of PFs in the alkaline matrix and solution, drying and wetting cycle conditions, and high-temperature conditions were reviewed. Finally, some paths to improve the alkaline degradation of PF reinforcement in the alkaline matrix were proposed. [ABSTRACT FROM AUTHOR]

Mycelium-based composites are a promising avenue for innovating sustainable materials from the hyphae of fungi. This study focuses on the use of fibers from four local fungal species, namely, Pleurotus ostreatus, Pleurotus sajor-caju (Fr. Singer), Auricularia auricula-judae, and Schizophyllum commune Fr., to produce mycelium-based composites from water hyacinth. An inoculum of each of the mushroom species was cultivated on PDA medium at 25 and 30 °C to determine the optimal temperature based on the growth rate. The obtained optimal condition was used to grow the fungi on water hyacinth (WH) mixed with rice bran in different proportions (100% WH, 70% WH, and 50% WH) with various numbers of fungal inocula (10, 20, and 30 plugs). The obtained composites were coated with a solution of either starch, chitosan, or epoxy resin. Schizophyllum commune Fr. exhibited the highest growth rate and fiber density, with a growth rate of 1.45 ± 1.92 mm/day at 30 °C. Ten inocula of Schizophyllum commune Fr. incubated at 30 °C for seven days on a mixture of 50% WH and 50% rice bran gave the optimal composite. Coating the obtained composite with chitosan improved its mechanical properties, but coating it with epoxy resin improved its water absorbency. Buried in soil, the composite coated with a chitosan solution decomposed within 30 days. The results indicate that Schizophyllum commune Fr. can be used as a binder to produce mycelial composites on a substrate of WH mixed with rice bran. The implications of these results will enable the further development and tuning of mushroom-based materials, especially for the production of sustainable bio-construction materials derived from local mushrooms and bio-waste. [ABSTRACT FROM AUTHOR]

The production of raw natural rubber always ends up with leftover latex. This latex is later collected to produce low grades of rubber. The collection of this latex also depends on the latex's quality. However, reproducing the latex may not be applicable if the latex contains many specks of dirt which will eventually be discarded. In this work, an alternative solution was to utilize such rubber in a processable form. This scrap rubber (SR) from the production of natural rubber grafted with polymethyl methacrylate (NR-g-PMMA) production was recovered to prepare an oil-swellable rubber. The rubber blends were turned into cellular structures to increase the oil swellability. To find the suitable formulation and cellular structure of the foam, the foams were prepared by blending SR with virgin natural rubber (NR) at various ratios, namely 0/100, 20/80, 30/70, 50/50, 70/30, 80/20, and 100/0 (phr/phr). The foam formation strongly depended on the SR, as it prevented gas penetration throughout the matrix. Consequently, small cells and thick cell walls were observed. This structure reduced the oil swellability from 7.09 g/g to 5.02 g/g. However, it is interesting to highlight that the thermal stability of the foam increased over the addition of SR, which is likely due to the higher thermal stability of the NR-g-PMMA waste or SR. In summary, the blending NR with 30 phr of SR provided good oil swellability, processability, and morphology, which benefit oil recovery application. The results obtained from this study will be used for further experiments on the enhancement of oil absorbency by applying other key factors. This work is considered a good initiative for preparing the oil-absorbent material based on scrap from modified natural rubber production. [ABSTRACT FROM AUTHOR]

Chronic wound is characterized by slow healing time, persistence, and abnormal healing progress. Therefore, serious complications can lead at worst to the tissue removal. In this scenario, there is an urgent need for an ideal dressing capable of high absorbency, moisture retention and antimicrobial properties. Herein we investigate the technical properties of a novel advanced non-woven triple layer gauze imbibed with a cream containing Rigenase, an aqueous extract of Triticum vulgare used for the treatment of skin injuries. To assess the applicability of this system we analyzed the dressing properties by wettability, dehydration, absorbency, Water Vapor Transmission Rate (WVTR), lateral diffusion and microbiological tests. The dressing showed an exudate absorption up to 50%. It created a most environment allowing a proper gaseous exchange as attested by the WVTR and a controlled dehydration rate. The results candidate the new dressing as an ideal medical device for the treatment of the chronic wound repairing process. It acts as a mechanical barrier providing a good management of the bacterial load and proper absorption of abundant wound exudate. Finally, its vertical transmission minimizes horizontal diffusion and side effects on perilesional skin as maceration and bacterial infection. [ABSTRACT FROM AUTHOR]

Polyacrylic acid (PAA) has high water absorbency but poor salt resistance. Humic acid (HA) extracted from lignite was introduced into the cross-linked copolymer systems of AA to improve the water absorbency and salt-tolerance. A polyacrylic acid-potassium humate (PAA-KHA) coated ammonium dihydrogen phosphate (ADP) fertilizer with water-preserving, salt-resistant and slow-release properties was prepared. The main properties of HA extracted from lignite oxidized by H2O2 were studied. Furthermore, the synthesis process, water absorbency of PAA-KHA in deionized water and in NaCl solution, morphologies of PAA-KHA, and the slow-release performance of the fertilizer (ADP@PAA-KHA) were investigated. The results showed PAA-KHA had a layered interpenetrating network, which can provide sufficient storage space for water and nutrients. The salty water absorbency of PAA-KHA increased by about 3 times compared to PAA. Both the PO43− and NH4+ cumulative release of ADP@PAA-KHA with a coating rate of 10% in deionized water, were less than 20% within 24 h, and were 55.71% and 28.04% after the 15th day, respectively. The weight change of ADP@PAA-KHA before and after absorbing water was about 53 times in deionized water and about 4 times in 1 wt% of NaCl salty water. The results show that ADP@PAA-KHA has excellent properties of water retention, salt resistance and slow-release. This will efficiently improve the utilization of fertilizer and reduce the irrigation water consumption at the same time. [ABSTRACT FROM AUTHOR]

Molded plywood is used for furniture components such as seats, backrests, or integral seat shells, and it must be durable and harmless to health. Molded plywood is made with urea-formaldehyde (UF) adhesives; therefore, the issue of the fillers used in them is important. The potential of using ground beech (Fagus sylvatica L.) bark as an eco-friendly additive in UF adhesives for molded plywood manufacturing was investigated in this work. Wheat flour was used as a reference filler. The beech bark (BB) level as a filler was 10%, a value verified under laboratory conditions. Nine-layer flat and molded plywood were produced under industrial conditions from beech veneers bonded with a UF adhesive mixture. The mechanical (bending strength and bonding quality) and physical (swelling and absorbency values after 2 and 24 h) properties of the industrially fabricated molded plywood were evaluated and compared with the European standard requirements (EN 310 and EN 314-2). The mechanical properties of the molded plywood with the addition of BB in the adhesive mixture were acceptable and met these standards' requirements. The positive effect of BB in the UF adhesive mixture on a reduction in formaldehyde emissions from the molded plywood was also confirmed. BB, considered to be wood-processing industry waste or a by-product, has significant potential to be used as a filler in UF resins for molded plywood production, providing an environmentally friendly, inexpensive solution for the industrial valorization of bark as a bio-based formaldehyde scavenger. [ABSTRACT FROM AUTHOR]

Lignin-poly(ethylene)glycol diglycidyl ether hydrogels were synthesized from lignin fractions readily extracted during the hot-water treatment of angiosperms: hardwoods, sugar maple and energy-crop willow, monocotyledons, grasses, miscanthus and agriculture residues, and wheat straw. These lignins represent a broad range of chemical structures and properties as a comparative analysis of their suitability to produce the hydrogels as a novel carrier of chaga–silver nanoparticles. The formation of hydrogels was assessed via attenuated total reflectance Fourier-transformed infrared spectroscopy. Then, the hydrogels were observed via scanning electron microscopy and evaluated for their free-absorbency capacity and moduli of compression. Furthermore, a hydrogel produced from kraft lignin and two commercial hydrogels was evaluated to benchmark the effectiveness of our hydrogels. Chaga extracts were prepared via the hot-water extraction of chaga mushroom, a method selected for its relatively higher yields and preserved antioxidizing activities. Hydrogels synthesized with lignins of monocotyledons, wheat straw, and miscanthus were found to be suitable carriers for chaga–silver nanoparticles due to their favorable absorption and release behaviors. [ABSTRACT FROM AUTHOR]

Paperboard boxes represent a sought-after class of packaging products, where the use of recycled fibers offers a cost-effective and environmentally friendly alternative to virgin fibers. The presence of a significant proportion of recycled fibers in the paperboard leads to a number of limitations associated with the deterioration of its characteristics. In this study, the properties of coated and uncoated paperboards containing recycled fibers, wood pulp, and virgin cellulose fibers were investigated using a laboratory sample of paperboard produced from 100% recycled fibers without any chemical additives for comparison. Properties such as smoothness, bulk density, absorbency, and tensile strength, as well as colorimetric characteristics, were determined for the recycled paperboards; for the latter test, charts were printed using inkjet printing and UV-curable inks. Whiteness was calculated by three formulae (CIE, Berger, and Stensby), and all the paperboards had a relatively low whiteness (not exceeding 90 CIE), with a yellowish tint due to recycled fibers and mechanical pulp in the composition. The absence of optical brightening agents in the paperboards was experimentally confirmed. The color gamuts of the paperboards were in direct ratio to their whiteness, with the highest ones demonstrated by the coated paperboards. Color reproduction, according to the tone value increase curves, also depended on the whiteness. Uncoated paperboards demonstrated smaller color shifts than the coated ones, with the greatest increase in tone for yellow color. Coated recycled paperboards are suitable for packaging printing under the same conditions as virgin fiber boards, while uncoated boards are the recommended choice for digital printing with UV inks. [ABSTRACT FROM AUTHOR]

Cellulose-based fibers are desirable materials for nonwoven wipes for their good absorbency, strength, cleaning, and biodegradable properties. However, quaternary ammonium compounds (QACs), being cationic in nature, show electrostatic interactions with anionic cellulosic fibers, reducing the available QACs to efficiently clean surfaces. This research presents sustainable alternative fibers that show better controlled exhaustion than commercial wipes and textile fibers. Textile and lignocellulosic fibers were prepared, soaked in QAC, and a UV–vis spectrophotometer was used to measure their exhaustion percentages. Factors such as immersion time and concentration of the disinfectant were also investigated, which affect the rate of exhaustion of the disinfectant from the fibers. A higher immersion time resulted in better exhaustion, whereas the total exhaustion decreased with an increase in the initial concentration of the disinfectant. The exhaustion of benzalkonium chloride (BAC) from the commercial wipes was also investigated at different immersion times and BAC concentrations. It was found that the wood and non-wood fibers showed more controlled exhaustion than the textile fibers and commercial wipes, and could be considered an alternative option for renewable and sustainable wipes and hygiene products. [ABSTRACT FROM AUTHOR]

Nanofibers are some of the most attractive materials that can modify functionalities for developing new kinds of specific applications and are mainly used as a biomedical material. Herein, we designed and prepared antibacterial nonwoven fiber mats of PLA and PLA composited with Ag nanoparticles by electrospinning. The effects of varying filler contents on their chemical, surface morphology, thermal, water absorbency, and antibacterial properties were investigated using FTIR, SEM/EDS, DSC, swelling ratio, and qualitative and quantitative antibacterial tests. FTIR and EDS spectra indicated that Ag nanoparticles were incorporated in the PLA without chemical bonding. SEM revealed that the average diameter of the PLA nanofibers containing the Ag nanoparticles was more significant than those without those particles. In addition, fiber diameters are proportional to the amount of Ag nanoparticle contents. DSC indicated that the Ag nanoparticles can be incorporated within the PLA matrix without strongly affecting their thermal properties. Moreover, the crystallinity of the composite nonwoven fiber mats was higher than those of fiber mats in the neat PLA. However, TGA revealed that the loaded Ag can improve the thermal stability of the PLA electrospun fiber mats. Accordingly, the antibacterial activities revealed that all the composite nanofiber mats exhibited excellent resistance against S. aureus and E. coli bacterial strains. In addition, in the cell toxicity study, all produced hybrids of nonwoven fiber mats induced a reduction in cell viability for the L929 fibroblast cells. Our results suggest that the designed and prepared nonwoven fiber mats may have good potential for use in the biomedical field, particularly in wound dressing applications. [ABSTRACT FROM AUTHOR]

Ten different hydrogels were prepared and analyzed from the point of view of their use in soil. FT-IR spectra, morphology, swelling ability, and rheological properties were determined for their characterization and appraisal of their stability. The aim was to characterize prepared materials containing different amounts of NPK as mineral fertilizer, lignohumate as a source of organic carbon, and its combination. This study of stability was focused on utility properties in their application in soil—repeated drying/re-swelling cycles and possible freezing in winter. Lignohumate supported the water absorbency, while the addition of NPK caused a negative effect. Pore sizes decreased with NPK addition. Lignohumate incorporated into polymers resulted in a much miscellaneous structure, rich in different pores and voids of with a wide range of sizes. NPK fertilizer supported the elastic character of prepared materials, while the addition of lignohumate shifted their rheological behavior to more liquid. Both dynamic moduli decreased in time. The most stable samples appeared to contain only one fertilizer constituent (NPK or lignohumate). Repeated re-swelling resulted in an increase in elastic character, which was connected with the gradual release of fertilizers. A similar effect was observed with samples that were frozen and defrosted, except samples containing a higher amount of NPK without lignohumate. A positive effect of acrylamide on superabsorbent properties was not confirmed. [ABSTRACT FROM AUTHOR]

The water absorption measurements of a novel superabsorbent anionic hydrogel, H-Na-PCMSA-g-PAN, has been reported first time in water with a poor conductivity, 0.15 M saline (NaCl, CaCl2, and AlCl3) solutions, and simulated urine (SU) solutions at various times. The hydrogel has been prepared by the saponification of the graft copolymer, Na-PCMSA-g-PAN (%G = 316.53, %GE = 99.31). Results indicated that as compared to the swelling capacity values evaluated in water with a poor conductivity, the ability of the hydrogel to swell in various saline solutions with the same concentration is significantly reduced at all different durations. The swelling tends to be Na+ > Ca2+ > Al3+ at the same saline concentration in the solution. Studies of the absorbency in various aqueous saline (NaCl) solutions also revealed that the swelling capacity decreased as the ionic strength of the swelling medium rose, which is consistent with the experimental results and Flory's equation. Furthermore, the experimental results strongly suggested that second-order kinetics governs the swelling process of the hydrogel in various swelling media. The swelling characteristics and equilibrium water contents for the hydrogel in various swelling media have also been researched. The hydrogel samples have been successfully characterized by FTIR to show the change in chemical environment to COO− and CONH2 groups after swelling in different swelling media. The samples have also been characterized by SEM technique. [ABSTRACT FROM AUTHOR]

Silicone gel sheeting (SGS) and pressure garment therapy (PGT) are the International Clinical Recommendations on Scar Management's (ICRSM) two principal non-invasive scar-healing procedures. This study created a new PGT-SGS composite (PGF-Biopor®AB-based) via pre-strained screen printing. The Biopor®AB hydrophobicity and nylon-hydrophilicity enabled self-pumping for PGT-SGS dual therapy and pressure-driven "warp insertions" mobility facilitates active-fluid transportation. Integrating both therapies in a single PGT-SGS composite achieved efficacy optimization, and the 3D channel structure allowed trauma-free active-fluid transport. The 3D channel topology enables smooth diffusional transport in active-fluid transport environments—and active "nylon absorbency" improved water uptake and enhanced permeability capabilities with sustainability achieved dynamic hydration. The sole use of PGF-Biopor®AB composite in empirical trials verified dual therapy with trauma-free active-fluid transport with one-month efficacy, providing a new route for dual treatment and active scar management. [ABSTRACT FROM AUTHOR]

Plant waste is a huge source of natural fibers and has great potential in the field of reinforced polymer composites to replace the environmentally harmful synthetic composites. In this study, fibers were extracted from water hyacinth (WH) petiole and sugarcane bagasse (SB) to make nonwovens by wet-laid web formation, and reinforced on the polyester (P) and epoxy (E) resins to make four types of composites namely, water hyacinth nonwoven reinforced epoxy (WH + E), water hyacinth nonwoven reinforced polyester (WH + P), sugarcane bagasse nonwoven reinforced epoxy (SB + E) and sugarcane bagasse nonwoven reinforced polyester (SB + P) composites. Water repellent (WR) on the nonwovens and gamma radiation (GR) on the composites were applied to improve the hydrophobicity and mechanical properties, such as tensile strength (TS), elongation at break and tensile modulus (TM) of the composites. The morphological structure of the fiber surfaces and tensile fractures were analyzed by SEM. FTIR spectra showed changes in functional groups before and after treatment. XRD analysis exhibited an increase in crystallinity for gamma-irradiated composites and a decrease in crystallinity for WR-treated composites compared to untreated composites. The SB composites (SB + E, SB + P) and polyester composites (WH + P, SB + P) showed higher water absorbency and lower mechanical properties than the WH composites (WH + E, WH + P) and epoxy composites (WH + E, SB + E), respectively. Hydrophobicity improved significantly by approximately 57% (average) at a concentration of 10% WR. However, TS and TM were reduced by approximately 24% at the same concentration. Thus, 5% WR is considered an optimum concentration due to the very low deterioration of TS and TM (<10%) but significant improvement in hydrophobicity (~39%) at this dose. On the other hand, GR treatment significantly improved TS, TM and hydrophobicity by 41, 32 and 25%, respectively, and decreased Eb% by 11% at a dose of 200 krd. However, mechanical properties and hydrophobicity deteriorated with further increase in dose at 300 krd. Thus, 200 krd is considered the optimum dose of GR. [ABSTRACT FROM AUTHOR]

One of the most important among the numerous applications of superabsorbent polymers (SAPs), also known as hydrogels, is soil improvement and supporting plant vegetation in agriculture and environmental engineering. Currently, when water scarcity involves water stress, they are becoming still more commonly used for water retention in soil. As it turns out, one of the major factors influencing the superabsorbent polymers water retention capacity (WRC) is the load of soil. The study presents test results of absorbency under load (AUL) of SAPs. The object of the analysis was cross-linked copolymer of acrylamide and potassium acrylate, of a granulation of 0.50-3.15 mm. The authors analysed the water absorption capacity of the superabsorbent polymers under loads characteristic for 3 different densities of soil (1.3 g·cm-3, 0.9 g·cm-3, 0.5 g·cm-3) and three different depths of application (10 cm, 20 cm, and 30 cm). Soil load and bulk densities were simulated by using weights. The experiments were conducted with a Mecmesin Multitest 2.5-xt apparatus. The obtained results demonstrate a very significant reduction in water absorption capacity by SAP under load. For a 30 cm deep layer of soil of bulk density of 1.3 g·cm-3, after 1 h, this value amounted to 5.0 g·g-1, and for the control sample without load, this value amounted to more than 200 g·g-1. For the lowest load in the experiment, which was 0.49 kPa (10 cm deep layer of soil of a bulk density of 0.5 g·cm-3), this value was 33.0 g·g-1 after 60 min. Loads do not only limit the volume of the swelling superabsorbent polymer but they also prolong the swelling time. The soil load caused a decrease in the absorption capacity from 338.5 g·g-1 to 19.3 g·g-1, as well as a prolongation of the swelling time. The rate parameter (time required to reach 63% of maximum absorption capacity) increased from 63 min for the control sample to more than 300 min for the largest analysed load of 3.83 kPa. The implications of soil load on superabsorbent polymer swelling are crucial for its usage and thus for the soil system. This knowledge might be employed for the more effective usage of superabsorbent polymers in agriculture and environmental engineering, in which they are commonly used to retain water and to support plant growth. [ABSTRACT FROM AUTHOR]

Exuding wound care requires a dressing to quickly absorb exudates and properly manage moisture during the healing process. In this study, the superabsorbent spacer fabrics were designed and fabricated for application in exuding wound dressings. The fabric structure consists of three layers, including two outer hydrophobic layers made of polyester/spandex yarns and one superabsorbent middle layer made of superabsorbent yarns. In order to confirm the performance of these superabsorbent spacer fabrics, their dressing properties were tested and compared with two commercial foam dressings. The results showed that all the superabsorbent spacer fabrics had much faster wetting speeds (less than 2 s) than the foam dressings (6.04 s for Foam A and 63.69 s for Foam B). The absorbency of the superabsorbent spacer fabrics was at least twice higher than that of the foam dressings. The air permeability of the superabsorbent spacer fabrics (higher than 15 mL/s/cm2 at 100 Pa) was much higher than that of the foam dressings which had a too low permeability to be measured by the testing device. In addition, the water vapor permeability, thermal insulation, and conformability of superabsorbent spacer fabrics were comparable to foam dressings. The study indicates that the superabsorbent spacer fabrics are suitable for exuding wound dressing applications. [ABSTRACT FROM AUTHOR]

Covalently crosslinked sodium carboxymethyl cellulose (CMC)–hydroxyethyl cellulose (HEC) hydrogel films were prepared using citric acid (CA) as the crosslinking agent. Thereafter, the physically crosslinked κ-carrageenan (κ-CG) polymer was introduced into the CMC–HEC hydrogel structure, yielding κ-CG/CMC–HEC double network (DN) hydrogels. The κ-CG physical network provided sacrificial bonding, which effectively dissipated the stretching energy, resulting in an increase in the tensile modulus, tensile strength, and fracture energy of the DN hydrogels by 459%, 305%, and 398%, respectively, compared with those of the CMC–HEC single network (SN) hydrogel. The dried hydrogels exhibited excellent water absorbency with a maximum water-absorption capacity of 66 g/g in distilled water. Compared with the dried covalent SN gel, the dried DN hydrogels exhibited enhanced absorbency under load, attributed to their improved mechanical properties. The water-absorption capacities and kinetics were dependent on the size of the dried gel and the pH of the water. [ABSTRACT FROM AUTHOR]

The improvement of gel strength and absorption properties through the surface-crosslinking of superabsorbent polymers (SAPs) is essential for sanitary industry applications. We prepared core-SAP via aqueous solution copolymerization, and then surface-crosslinked the core-SAP under various conditions. The structure of the SAP was characterized using Fourier transform infrared (FT-IR) spectroscopy. Central composite design (CCD) of response surface methodology (RSM) has been applied to determine the optimum surface-crosslinking conditions such as surface-crosslinker content, reaction temperature, and reaction time. The optimal surface-crosslinking conditions were identified at a surface-crosslinker content of 2.22 mol%, reaction temperature of 160 °C, and reaction time of 8.7 min. The surface-crosslinked SAP showed excellent absorbency under load of 50 g/g with a permeability of 50 s. Other absorption properties were also evaluated by measuring the free absorbency and centrifuge retention capacity in saline solution. [ABSTRACT FROM AUTHOR]

Nanosilica was surface modified with polyaniline and incorporated into polyurethane to form a polymer matrix capable of entrapping a liquid electrolyte and functioning as quasi-solid-state electrolyte in the dye-sensitized solar cells. The effect on the S−PANi distribution, surface morphology, thermal stability, gel content, and structural change after varying the PEG molecular weight of the polyurethane matrix was analyzed. Quasi-solid-state electrolytes were prepared by immersing the polyurethane matrix into a liquid electrolyte and the polymer matrix absorbency, conductivity, and ion diffusion were investigated. The formulated quasi-solid-state electrolytes were applied in dye-sensitized solar cells and their charge recombination, photovoltaic performance, and lifespan were measured. The quasi-solid-state electrolyte with a PEG molecular weight of 2000 gmol−1 (PU−PEG 2000) demonstrated the highest light-to-energy conversion efficiency, namely, 3.41%, with an open-circuit voltage of 720 mV, a short-circuit current of 4.52 mA cm−2, and a fill factor of 0.63. [ABSTRACT FROM AUTHOR]

The current study sought to synthesize silver nanoparticles (AgNPs) from Amaryllis vittata (L.) leaf and bulb extracts in order to determine their biological significance and use the toxic plants for human health benefits. The formation of silver nanoparticles was detected by a change in color from whitish to brown for bulb-AgNPs and from light green to dark brown for leaf-AgNPs. For the optimization of silver nanoparticles, various experimental physicochemical parameters such as pH, temperature, and salt were determined. UV-vis spectroscopy, Fourier transform infrared spectroscopy, X-ray dispersion spectroscopy, scanning electron microscopy, and energy dispersion spectroscopy analysis were used to characterize nanoparticles. Despite the fact that flavonoids in plant extracts were implicated in the reduction and capping procedure, the prepared nanoparticles demonstrated maximum absorbency between 400 and 500 nm. SEM analysis confirmed the preparation of monodispersed spherical crystalline particles with fcc structure. The bioinspired nanoparticles were found to show effective insecticidal activity against Tribolium castaneum and phytotoxic activity against Lemna aequincotialis. In comparison to plant extracts alone, the tested fabricated nanoparticles showed significant potential to scavenge free radicals and relieve pain. Antibacterial testing against human pathogenic strains, i.e., Escherichia coli and Pseudomonas aureginosa, and antifungal testing against Aspergillus niger revealed the significant potential for microbe resistance using AgNPs. As a result of the findings, the tested silver nanoparticles demonstrated promising potential for developing new and effective pharmacological and agricultural medications. Furthermore, the effects of biogenic AgNPs on an in vitro culture of Solanum tuberosum L. plants were investigated, and the findings indicated that bulb-AgNPs and leaf-AgNPs produced biomass and induced antioxidants via their active constituents. As a result, bulb-AgNPs and leaf-AgNPs may be recommended for use in Solanum tuberosum L. tissue culture for biomass fabrication and metabolic induction. [ABSTRACT FROM AUTHOR]

The contraction stress generated during the photopolymerization of resin dental composites is the major disadvantage. The water sorption in the oral environment should counteract the contraction stress. The purpose was to evaluate the influence of the water sorption of composite materials on polymerization shrinkage stress generated at the restoration-tooth interface. The following materials were tested: Filtek Ultimate, Gradia Direct LoFlo, Heliomolar Flow, Tetric EvoCeram, Tetric EvoCeram Bulk Fill, Tetric EvoFlow, Tetric EvoFlow Bulk Fill, X-tra Base, Venus BulkFil, and Ceram.X One. The shrinkage stress was measured immediately after curing and after: 0.5 h, 24 h, 72 h, 96 h, 168 h, 240 h, 336 h, 504 h, 672 h, and 1344 h by means of photoelastic study. Moreover, water sorption and solubility were evaluated. Material samples were weighted on scale in time intervals to measure the water absorbency and the dynamic of this process. The tested materials during polymerization generated shrinkage stresses ranging from 6.3 MPa to 12.5 MPa. Upon water conditioning (56 days), the decrease in shrinkage strain (not less than 48%) was observed. The decrease in value stress in time is material-dependent. [ABSTRACT FROM AUTHOR]

Hypertrophic scars (HTSs) are pathological structures resulting from chronic inflammation during the wound healing process, particularly in complex injuries like burns. The aim of this work is to propose Biofiber PF (biodegradable fiber loaded with Pirfenidone 1.5 w/w), an electrospun advanced dressing, as a solution for HTSs treatment in complex wounds. Biofiber has a 3-day antifibrotic action to modulate the fibrotic process and enhance physiological healing. Its electrospun structure consists of regular well-interconnected Poly-L-lactide-co-poly-ε-caprolactone (PLA-PCL) fibers (size 2.83 ± 0.46 µm) loaded with Pirfenidone (PF, 1.5% w/w), an antifibrotic agent. The textured matrix promotes the exudate balance through mild hydrophobic wettability behavior (109.3 ± 2.3°), and an appropriate equilibrium between the absorbency % (610.2 ± 171.54%) and the moisture vapor transmission rate (0.027 ± 0.036 g/min). Through its finer mechanical properties, Biofiber PF is conformable to the wound area, promoting movement and tissue oxygenation. These features also enhance the excellent elongation (>500%) and tenacity, both in dry and wet conditions. The ancillary antifibrotic action of PF on hypertrophic scar fibroblast (HSF) for 3 days downregulates the cell proliferation over time and modulates the gene expression of transforming growth factor β1 (TGF-β1) and α-smooth muscle actin (α-SMA) at 48–72 h. After 6 days of treatment, a decrement of α-SMA protein levels was detected, proving the potential of biofiber as a valid therapeutic treatment for HTSs in an established wound healing process. [ABSTRACT FROM AUTHOR]

Recently, the natural polymer polysaccharide konjac glucomannan (KGM) has received attention as a promising adsorbent in water treatment due to its low toxicity, cost-effectiveness and biocompatibility. However, the high-level water absorbency of KGM makes it difficult to recover in water treatment. In this study, by combining KGM with magnetic nanoparticles, KGM-based magnetic nanoparticles (KGM-Fe3O4 NPs) with excellent adsorption properties and recyclability for heavy metals were prepared using an one-step precipitation method. The as-prepared KGM-Fe3O4 NPs have a spherical morphology of superparamagnetism with a small particle size (ca. 7.0 nm) and a large specific surface area (160.1 m2·g−1). Taking Cr(VI) as the target heavy metal ion, the above nanoparticles have a high adsorption capacity and fast adsorption rate for Cr(VI). The pseudo-second order kinetic model is more suitable to describe the adsorption process of Cr(VI) by KGM-Fe3O4 NPs, and the maximum adsorption capacity of Cr(VI) onto KGM-Fe3O4 NPs was calculated to be 41.67 mg·g−1 using the Langmuir isotherm model. In addition, KGM-Fe3O4 NPs with adsorbed heavy metal ions can be quickly recovered from a solution, regenerated, and reused in the next cycle. KGM-based Fe3O4 nanoparticles are promising adsorbents that show significant reusability for the removal of metal ions in water and wastewater treatment. [ABSTRACT FROM AUTHOR]

In recent years, there has been growing interest in using plant fibers to reinforce materials in modern manufacturing. This study focuses on the development of a novel biocomposite made from an enset fiber (EF) and polylactic acid (PLA) matrix using compression molding at a hot-pressing temperature of 170 °C and pressure of 7 MPa for 7 min. Before preparing the biocomposites, the fibers were chemically modified with different concentrations of sodium hydroxide (NaOH) and cut into shorter fibers with a 40 mm average length in size. Then, the extent of modifications on the mechanical properties, dynamic mechanical behavior, morphology, and water absorption were investigated. The tensile, flexural, and Charpy impact tests were carried out to evaluate the mechanical properties of the samples as per ASTM standards. Moreover, dynamic mechanical analysis (DMA) and the water absorbency of the biocomposites were investigated, and the results were graphically shown and explained. The results indicate that the biocomposite treated with 5% NaOH exhibited significant improvements in tensile strength, flexural strength, and impact strength compared to the untreated composite. The tensile modulus and flexural modulus of 5% NaOH-modified enset fiber biocomposite were also enhanced by 55.8% and 70.3% compared to untreated enset fiber biocomposite. The highest tensile strength, flexural strength, and impact strength found for the PLA composite reinforced by EF treated with 5% w/v NaOH solution were 20.16 MPa, 30.21 MPa, and 12.02 kJ/m2, respectively. In general, the modification of natural fibers improves adhesion at the interface and therefore decreases the water absorption and improves the dynamic mechanical properties of biocomposites. [ABSTRACT FROM AUTHOR]

Increasing levels of dissolved organic matter (DOM) in watercourses in the northern hemisphere are mainly due to reduced acid rain, climate change, and changes in agricultural practices. However, their impacts vary in time and space. To predict how DOM responds to changes in environmental pressures, we need to differentiate between allochthonous and autochthonous sources as well as identify anthropogenic DOM. In this study we distinguish between allochthonous, autochthonous, and anthropogenic sources of DOM in a diverse watercourse network by assessing effects of land cover on water quality and using DOM characterization tools. The main sources of DOM at the studied site are forests discharging allochthonous humic DOM, autochthonous fulvic DOM, and runoff from urban sites and fish farms with high levels of anthropogenic DOM rich in protein-like material. Specific UV absorbency (sUVa) distinguishes allochthonous DOM from autochthonous and anthropogenic DOM. Anthropogenic DOM differs from autochthonous fulvic DOM by containing elevated levels of protein-like material. DOM from fishponds is distinguished from autochthonous and sewage DOM by having high sUVa. DOM characteristics are thus valuable tools for deconvoluting the various sources of DOM, enabling water resource managers to identify anthropogenic sources of DOM and predict future trends in DOM. [ABSTRACT FROM AUTHOR]

For the development of biodegradable superabsorbent polymers, the effect of the cross-linking length on the absorption characteristics of the Na salt of polyaspartic acid (PAspNa) was demonstrated using different concentrations of diamine cross-linking agents bearing carbon chains of different lengths, viz., ethylenediamine, 1,6-hexamethylenediamine, 1,8-diaminooctane, 1,10-diaminodecane, and 1,12-diaminododecane were used as cross-linking agents. The absorption of PAspNa was measured in deionised water and in a 0.9% aqueous NaCl solution. Under the conditions tested, when the alkyl chain of PAspNa was too short or too long, the absorbency was low and the cross-linking length was optimum. The success of the cross-linking reaction was confirmed by FT-IR spectroscopy. The degree of cross-linking was estimated and the ideal concentration for maximum water absorption was determined by elemental analysis. The sample obtained by cross-linking 1,8-diaminooctane at a concentration of 0.11 g/g polysuccinimide (PSI) showed the highest absorption. The thermal properties of each material were determined by dynamic scanning calorimetry. Therefore, the length of the cross-linking agent was found to strongly influence water absorption. [ABSTRACT FROM AUTHOR]

In order to achieve the low cost and multifunction of superabsorbent composites, poly(acrylic acid-co-acrylamide)/fulvic acid/oil shale semicoke (PAMFS) were prepared by free radical copolymerization of fulvic acid (FA), oil shale semicoke (OSSC), acrylic acid (AA) and acrylamide (AM). The characterization results revealed that FA and OSSC were involved in the construction of a three-dimensional (3D) polymeric network via hydrogen bonding and covalent bonding. The water absorbency of PAMFS in distilled water and 0.9 wt% NaCl solution were 724 and 98 g/g, respectively. The FA slow release of PAMFS in distilled water and soil was achieved due to the interaction between FA and the functional groups of polymer matrix by hydrogen bonds and covalent bonds. Furthermore, the potted experiment indicated that the addition of PAMFS to soil can significantly promote plant growth compared with the pure soil, regardless of water stress. Therefore, this superabsorbent composite showed an excellent water absorption and salt resistance performance, as well as nice slow release performance. It has a broad application prospect. [ABSTRACT FROM AUTHOR]

Cellulose-based superabsorbent was synthesized by bacterial cellulose (BC) grafting acrylic acid (AA) in the presence of N,N′-methylenebisacrylamide (NMBA) as a crosslinker and ammonium persulfate (APS) as an initiator. The influence of different factors on composite synthesis, including the weight ratio of the monomer to BC, initiator content, crosslinker content, AA neutralization degree, reaction temperature, and reaction time on the water absorbency of the composite, were systematically learned. Under the optimized conditions, the maximum water absorbency of the composite was 322 ± 23 g/g distilled water. However, the water absorbency was much less for the different salt solutions and the absorption capacity of the composite decreased as the concentration of the salt solutions increased. The pH value had a significant influence on water absorption performance, and with the increase of temperature, the water retention rate of the composite decreased. Additionally, the structure of this composite was characterized with nuclear magnetic resonance (NMR), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). The results of NMR and FT-IR provided evidence that the composite was synthesized by BC and AA, and the microstructure showed that it had good performance for water absorption. In addition, the composite possessed suitable thermal stability, and that it could be used in a few high-temperature environments. Overall, this composite is promising for application in water absorption. [ABSTRACT FROM AUTHOR]

Matricaria chamomilla L. extract is well-known for its therapeutic properties; thus, it shows potential to be used to modify materials designed for biomedical purposes. In this paper, acrylic hydrogels modified with this extract were prepared. The other modifier was starch introduced into the hydrogel matrix in two forms: room-temperature solution and elevated-temperature solution. Such hydrogels were synthesized via UV radiation, while two types of photoinitiator were used: 2-hydroxy-2-methylpropiophenone or phenylbis(2,4,6-trimethylbenzoyl) phosphine oxide. The main task of performed research was to verify the impact of particular modifiers and photoinitiator on physicochemical properties of hydrogels. Studies involved determining their swelling ability, elasticity, chemical structure via FTIR spectroscopy and surface morphology via the SEM technique. Incubation of hydrogels in simulated physiological liquids, studies on the release of chamomile extract from their matrix and their biological analysis via MTT assay were also performed. It was demonstrated that all investigated variables affected the physicochemical properties of hydrogels. The modification of hydrogels with chamomile extract reduced their absorbency, decreased their thermal stability and increased the cell viability incubated with this material by 15%. Next, hydrogels obtained by using phenylbis(2,4,6-trimethylbenzoyl) phosphine oxide as a photoinitiator showed lower absorbency, more compact structure, better stability in SBF and a more effective release of chamomile extract compared to the materials prepared by using 2-hydroxy-2-methylpropiophenone. It was proved that, by applying adequate reagents, including both photoinitiator and modifiers, it is possible to obtain hydrogels with variable properties that will positively affect their application potential. [ABSTRACT FROM AUTHOR]

In commercial terms, Extra Virgin Olive Oil (EVOO) is considered an exceptional food with excellent sensory and nutritional quality due to its taste, odor, and bioactive compounds; as such, it is of great health interest. This quality can be affected by the oxidative degradation, both chemical and enzymatic (the activity of oxidative, endogenous enzymes from the polyphenol oxidase and peroxidase olive fruit type), of essential components during the extraction and conservation of EVOO. In the bibliography, oxygen reduction during the malaxation process and oil storage has been studied in different ways. However, research concerning oxygen reduction in the crushing of the olive fruit or the malaxation of the paste, or both, in the "real extraction condition" is scarce. Oxygen reduction has been compared to control conditions (the concentration of atmospheric oxygen (21%)). Batches of 200 kg of the olive fruit, 'Picual' cultivar, were used and the following treatments were applied: Control (21% O2 Mill–21% O2 Mixer), "IC-NM": Inerted crushing -Normal malaxation (6.25% O2 Mill-21% O2 Mixer), "NC-IM": Normal crushing-Inerted malaxation (21% O2 Mill-4.39% O2 Mixer) and "IC-IM": Inerted crushing -Inerted malaxation (5.5% O2 Mill-10.5% O2 Mixer). The parameters of commercial quality covered by regulation (free acidity, peroxide value and absorbency in ultra-violet (K232 and K270)) did not suffer any change concerning the control, and so the oils belong to the commercial category of "Extra Virgin Olive Oil". The phenolic compounds of the olives involved in the distinctive bitter and pungent taste, health properties, and oxidative stability are increased with the downsizing amounts of oxygen in the IC-NM, NC-IM, and IC-IM treatments with an average of 4, 10, and 20%, respectively. In contrast, the total amount of volatile compounds decreases by 10–20% in all oxygen reduction treatments. The volatile compounds arising from the lipoxygenase pathway, which are responsible for the green and fruity notes of EVOO, also decreased in concentration with the treatments by 15–20%. The results show how oxygen reduction in the milling and malaxation stages of olive fruit can modulate the content of phenols, volatile compounds, carotenoids, and chlorophyll pigments in the EVOO to avoid the degradation of the compound with sensorial and nutritional interest. [ABSTRACT FROM AUTHOR]

Bone defects and infections pose significant challenges for treatment, requiring a comprehensive approach for prevention and treatment. Thus, this study sought to evaluate the efficacy of various bone allografts in the absorption and release of antibiotics. A specially designed high-absorbency, high-surface-area carrier graft composed of human demineralized cortical fibers and granulated cancellous bone (fibrous graft) was compared to different human bone allograft types. The groups tested here were three fibrous grafts with rehydration rates of 2.7, 4, and 8 mL/g (F(2.7), F(4), and F(8)); demineralized bone matrix (DBM); cortical granules; mineralized cancellous bone; and demineralized cancellous bone. The absorption capacity of the bone grafts was assessed after rehydration, the duration of absorption varied from 5 to 30 min, and the elution kinetics of gentamicin were determined over 21 days. Furthermore, antimicrobial activity was assessed using a zone of inhibition (ZOI) test with S. aureus. The fibrous grafts exhibited the greatest tissue matrix absorption capacity, while the mineralized cancellous bone revealed the lowest matrix-bound absorption capacity. For F(2.7) and F(4), a greater elution of gentamicin was observed from 4 h and continuously over the first 3 days when compared to the other grafts. Release kinetics were only marginally affected by the varied incubation times. The enhanced absorption capacity of the fibrous grafts resulted in a prolonged antibiotic release and activity. Therefore, fibrous grafts can serve as suitable carrier grafts, as they are able to retain fluids such as antibiotics at their intended destinations, are easy to handle, and allow for a prolonged antibiotic release. Application of these fibrous grafts can enable surgeons to provide longer courses of antibiotic administration for septic orthopedic indications, thus minimizing infections. [ABSTRACT FROM AUTHOR]

Four types of nonwovens were prepared from different sections of the banana tree e.g., outer bark (OB), middle bark (MB), inner bark (IB) and midrib of leaf (MR) by wet laid web formation. They were reinforced with two different types of matrices e.g., epoxy and polyester, to make eight variants of composites. Treatments including alkali on raw fibers, water repellent on nonwovens and gamma radiation on composites were applied in order to investigate their effects on properties of the composites such as water absorbency, tensile strength (TS), flexural strength (FS) and elongation at break (Eb%). Variations in the morphological structure and chemical composition of both raw banana fibers and fibers reinforced by the treatments were analyzed by Fourier Transform Infrared (FTIR) and Scanning Electron Microscopy (SEM). OB composites exhibited higher water absorbency, TS and FS and lower Eb% compared to other types of composites. Epoxy composites were found to have 16% lower water absorbency, 41.2% higher TS and 39.1% higher FS than polyester composites on an average. Water absorbency of the composites was reduced 32% by the alkali treatment and a further 63% by water repellent treatment. TS and FS of the composites were on average improved 71% and 87% by alkali treatment and a further 30% and 35% by gamma radiation respectively. [ABSTRACT FROM AUTHOR]

The furnish management of tissue materials is fundamental to obtain maximum quality products with a minimum cost. The key fiber properties and fiber modification process steps have a significant influence on the structural and functional properties of tissue paper. In this work, two types of additives, a commercial biopolymer additive (CBA) that replaces the traditional cationic starch and micro/nanofibrillated cellulose (CMF), were investigated. Different formulations were prepared containing eucalyptus fibers and softwood fibers treated mechanically and enzymatically and both pulps with these two additives incorporated independently and simultaneously with drainage in the tissue process range. The use of these additives to reduce the percentage of softwood fibers on tissue furnish formulations was investigated. The results indicated that a maximum of tensile strength was obtained with a combination of both additives at the expense of softness and water absorbency. With a reduction of softwood fibers, the incorporation of additives increased the tensile strength and water absorbency with a slight decrease in HF softness compared with a typical industrial furnish. Additionally, a tissue computational simulator was also used to predict the influence of these additives on the final end-use properties. Both additives proved to be a suitable alternative to reduce softwood fibers in the production of tissue products, enhancing softness, strength and absorption properties. [ABSTRACT FROM AUTHOR]

Hypertrophic scars (HTSs) are aberrant structures that develop where skin is injured complexly and represent the result of a chronic inflammation as a healing response. To date, there is no satisfactory prevention option for HTSs, which is due to the complexity of multiple mechanisms behind the formation of these structures. The present work aimed to propose Biofiber (Biodegradable fiber), an advanced textured electrospun dressing, as a suitable solution for HTS formation in complex wounds. Biofiber has been designed as a 3-day long-term treatment to protect the healing environment and enhance wound care practices. Its textured matrix consists of homogeneous and well-interconnected Poly-L-lactide-co-poly-ε-caprolactone (PLA-PCL) electrospun fibers (size 3.825 ± 1.12 µm) loaded with Naringin (NG, 2.0% w/w), a natural antifibrotic agent. The structural units contribute to achieve an optimal fluid handling capacity demonstrated through a moderate hydrophobic wettability behavior (109.3 ± 2.3°), and a suitable balance between absorbency (389.8 ± 58.16%) and moisture vapor transmission rate (MVTR, 2645 ± 60.43 g/m2 day). The flexibility and conformability of Biofiber to the body surfaces is due to its innovative circular texture, that also allow it to obtain finer mechanical properties after 72 h in contact with Simulated Wound Fluid (SWF), with an elongation of 352.6 ± 36.10%, and a great tenacity (0.25 ± 0.03 Mpa). The ancillary action of NG results in a prolonged anti-fibrotic effect on Normal Human Dermal Fibroblasts (NHDF), through the controlled release of NG for 3 days. The prophylactic action was highlighted at day 3 with the down regulation of the major factors involved in the fibrotic process: Transforming Growth Factor β1 (TGF-β1), Collagen Type 1 alpha 1 chain (COL1A1), and α-smooth muscle actin (α-SMA). No significant anti-fibrotic effect has been demonstrated on Hypertrophic Human Fibroblasts derived from scars (HSF), proving the potential of Biofiber to minimize HTSs in the process of early wound healing as a prophylactic therapy. [ABSTRACT FROM AUTHOR]