Search

Nine copolymers of acrylic acid and sodium methallyl sulfonate were tested as scale inhibitors in thermal desalination. The nine antiscalants covered molar masses between 2000 and 9500 g.mol–1 and concentrations of sulfonated monomer ranging between 10 and 30 mole percent. A pressure measurement and control (P-MAC) unit and a high-temperature pressurized vessel were used to measure the effectiveness of the scale inhibitors in seawater, concentrated seawater, and model solutions at 125 °C. The effectiveness of the novel copolymers was comparable to commercial antiscalant at times up to 15 min and improved at longer times. Molar mass was a more important determinant of effectiveness than degree of sulfonation, with the greatest mitigation of calcium sulfate precipitation observed for antiscalants of molar mass 2000 to 2500 g.mol–1 regardless of sulfonate content. Antiscalants of molar mass 4500 to 5000 g.mol–1 showed a higher threshold effect than antiscalants of molar mass 7000 to 9500 g.mol–1, with a 30% sulfonated polymer of molar mass 4500 g.mol–1 performing appreciably better than other polymers of a similar molar mass. [ABSTRACT FROM AUTHOR]

Binary and ternary copolymers of acrylonitrile (AN), tert-butyl acrylate (TBA), and n-butyl acrylate (BA) are synthesized through conventional radical polymerization in DMSO in the presence of 2-mercaptoethanol. The thermal behavior of binary and ternary copolymers is studied under argon atmosphere and in air. It is demonstrated that the copolymers of AN contain 1–10 mol.% of TBA split isobutylene upon heating above 160 °C, resulting in the formation of the units of acrylic acid in the chain. The carboxylic groups formed in situ are responsible for the ionic mechanism of cyclization, which starts at lower temperatures compared with pure polyacrylonitrile (PAN) or AN copolymer with BA. The activation energy of cyclization through ionic and radical mechanisms depends on copolymer composition. For the ionic mechanism, the activation energy lies in the range ca. 100–130 kJ/mole, while for the radical mechanism, it lies in the range ca. 150–190 kJ/mole. The increase in the TBA molar part in the copolymer is followed by faster consumption of nitrile groups and the evolution of a ladder structure in both binary and ternary copolymers. Thus, the incorporation of a certain amount of TBA in PAN or its copolymer with BA allows tuning the temperature range of cyclization. This feature seems attractive for applications in the production of melt-spun PAN by choosing the appropriate copolymer composition and heating mode. [ABSTRACT FROM AUTHOR]

Hybrid nanocomposites combining biopolymer fibers incorporated with nanoparticles (NPs) have received increasing attention due to their remarkable characteristics. Inorganic NPs are typically chosen for their properties, such as magnetism and thermal or electrical conductivity, for example. Meanwhile, the biopolymer fiber component is a backbone, and could act as a support structure for the NPs. This shift towards biopolymers over traditional synthetic polymers is motivated by their sustainability, compatibility with biological systems, non-toxic nature, and natural decomposition. This study employed the solution blow spinning (SBS) method to obtain a nanocomposite comprising poly(vinyl pyrrolidone), PVA, and gelatin biodegradable polymer fibers incorporated with magnetic iron oxide nanoparticles coated with poly(acrylic acid), PAA2k, coded as γ-Fe2O3-NPs-PAA2k. The fiber production process entailed a preliminary investigation to determine suitable solvents, polymer concentrations, and spinning parameters. γ-Fe2O3-NPs were synthesized via chemical co-precipitation as maghemite and coated with PAA2k through the precipitation–redispersion protocol in order to prepare γ-Fe2O3-NPs-PAA2k. Biopolymeric fibers containing coated NPs with sub-micrometer diameters were obtained, with NP concentrations ranging from 1.0 to 1.7% wt. The synthesized NPs underwent characterization via dynamic light scattering, zeta potential analysis, and infrared spectroscopy, while the biopolymer fibers were characterized through scanning electron microscopy, infrared spectroscopy, and thermogravimetric analysis. Overall, this study demonstrates the successful implementation of SBS for producing biopolymeric fibers incorporating iron oxide NPs, where the amalgamation of materials demonstrated superior thermal behavior to the plain polymers. The thorough characterization of the NPs and fibers provided valuable insights into their properties, paving the way for their potential applications in various fields such as biomedical engineering, environmental remediation, and functional materials. [ABSTRACT FROM AUTHOR]

Recently, eutectogels have emerged as ideal candidates for flexible wearable strain sensors. However, the development of eutectogels with robust mechanical strength, high stretchability, excellent transparency, and desirable conductivity remains a challenge. Herein, a covalently cross-linked eutectogel was prepared by exploiting the high solubility of oligoethylene glycol in a polymerizable deep eutectic solvent (DES) form of acrylic acid (AA) and choline chloride (ChCl). The resulting eutectogel exhibited high transparency (90%), robust mechanical strength (up to 1.5 MPa), high stretchability (up to 962%), and desirable ionic conductivity (up to 1.22 mS cm−1). The resistive strain sensor fabricated from the eutectogel exhibits desirable linear sensitivity (GF: 1.66), wide response range (1–200%), and reliable stability (over 1000 cycles), enabling accurate monitoring of human motions (fingers, wrists, and footsteps). We believe that our DES-based eutectogel has great potential for applications in wearable strain sensors with high sensitivity and reliability. [ABSTRACT FROM AUTHOR]

Microgel particles can play a key role, e.g., in drug delivery systems, tissue engineering, advanced (bio)sensors or (bio)catalysis. Amine-functionalized microgels are particularly interesting in many applications since they can provide pH responsiveness, chemical functionalities for, e.g., bioconjugation, unique binding characteristics for pollutants and interactions with cell surfaces. Since the incorporation of amine functionalities in controlled amounts with predefined architectures is still a challenge, here, we present a novel method for the synthesis of responsive core–shell nanogels (dh < 100 nm) with a poly(N-isopropylacrylamide) (pNIPAm) core and a polyamine shell. To achieve this goal, a surface-functionalized pNIPAm nanogel was first prepared in a semi-batch precipitation polymerization reaction. Surface functionalization was achieved by adding acrylic acid to the reaction mixture in the final stage of the precipitation polymerization. Under these conditions, the carboxyl functionalities were confined to the outer shell of the nanogel particles, preserving the core's temperature-responsive behavior and providing reactive functionalities on the nanogel surface. The polyamine shell was prepared by the chemical coupling of polyethyleneimine to the nanogel's carboxyl functionalities using a water-soluble carbodiimide (EDC) to facilitate the coupling reaction. The efficiency of the coupling was assessed by varying the EDC concentration and reaction temperature. The molecular weight of PEI was also varied in a wide range (Mw = 0.6 to 750 kDa), and we found that it had a profound effect on how many polyamine repeat units could be immobilized in the nanogel shell. The swelling and the electrophoretic mobility of the prepared core–shell nanogels were also studied as a function of pH and temperature, demonstrating the successful formation of the polyamine shell on the nanogel core and its effect on the nanogel characteristics. This study provides a general framework for the controlled synthesis of core–shell nanogels with tunable surface properties, which can be applied in many potential applications. [ABSTRACT FROM AUTHOR]

This study provides a detailed picture of how a protein (lysozyme) complexes with a poly(acrylic acid) polyelectrolyte (PAA) in water at the atomic level using a combination of all-atom molecular dynamics simulations and experiments. The effect of PAA and temperature on the protein's structure is explored. The simulations reveal that a lysozyme's structure is relatively stable except from local conformational changes induced by the presence of PAA and temperature increase. The effect of a specific thermal treatment on the complexation process is investigated, revealing both structural and energetic changes. Certain types of secondary structures (i.e., α-helix) are found to undergo a partially irreversible shift upon thermal treatment, which aligns qualitatively with experimental observations. This uncovers the origins of thermally induced aggregation of lysozyme with PAA and points to new PAA/lysozyme bonds that are formed and potentially enhance the stability in the complexes. As the temperature changes, distinct amino acids are found to exhibit the closest proximity to PAA, resulting into different PAA/lysozyme interactions; consequently, a different complexation pathway is followed. Energy calculations reveal the dominant role of electrostatic interactions. This detailed information can be useful for designing new biopolymer/protein materials and understanding protein function under immobilization of polyelectrolytes and upon mild denaturation processes. [ABSTRACT FROM AUTHOR]

Hybrid hydrogels with superabsorbent properties based on acrylic acid (20%), sodium alginate (0.5%) and poly(ethylene oxide) (0.1%) were obtained by electron-beam irradiation between 5 and 20 kGy, and are characterized by different physical and chemical methods; the first results reported showed gel fractions over 87%, cross-link densities under 9.9 × 103 mol/cm3 and swelling degrees of 400 g/g. Two types of hydrogels (without and with 0.1% initiator potassium persulfate) have been subjected to swelling and deswelling experiments in different swelling media with different pHs, chosen in accordance with the purpose for which these superabsorbent materials were obtained, i.e., water and nutrients carriers for agricultural purposes: 6.05 (distilled water), 7.66 (tap water), 5.40 (synthetic nutrient solution) and 7.45 (organic nutrient solution). Swelling kinetics and swelling dynamics have been also studied in order to investigate the influence of swelling media type and pH on the absorption phenomenon. The swelling and deswelling behaviors were influenced by the hydrogel characteristics and pH of the swelling media. Both the polymeric chain relaxation (non-Fickian diffusion) and macromolecular relaxation (super case II) phenomenon were highlighted as a function of swelling media type. [ABSTRACT FROM AUTHOR]

Zn–air batteries (ZABs) are a promising technology; however, their commercialization is limited by challenges, including those occurring in the electrolyte, and thus, gel polymer electrolytes (GPEs) and hydrogels have emerged as substitutes for traditional aqueous electrolytes. In this work, PVA/PAA membranes were synthesized by the solvent casting method and soaked in 6 M KOH to act as GPEs. The thickness of the membrane was modified (50, 100, and 150 μm), and after determining the best thickness, the membrane was modified with synthesized SiO2 nanospheres and multi-walled carbon nanotubes (CNTs). SEM micrographs revealed that the CNTs displayed lengths of tens of micrometers, having a narrow diameter (95 ± 7 nm). In addition, SEM revealed that the SiO2 nanospheres had homogeneous shapes with sizes of 110 ± 10 nm. Physicochemical experiments revealed that SiO2 incorporation at 5 wt.% increased the water uptake of the PVA/PAA membrane from 465% to 525% and the ionic conductivity to 170 mS cm−1. The further addition of 0.5 wt.% CNTs did not impact the water uptake but it promoted a porous structure, increasing the power density and the stability, showing three-times-higher rechargeability than the ZAB operated with the PVA/PAA GPE. [ABSTRACT FROM AUTHOR]

An alternative synthetic pathway was proposed for the optimization of synthesis to find a better correlation between the swelling and elasticity of hyaluronic acid-interpenetrated gels via temperature regulation. An experimental design methodology was presented for the synthesis of polyacrylamide/poly(acrylic acid sodium salt)/hyaluronic acid, PAAm/PSA/HyA, gels by modifying the one-pot procedure using free radical crosslinking copolymerization of AAm with the addition of anionic linear PSA chains in the presence of various amount of HyA, ranging between 0.05% and 0.20% (w/v). Semi-interpenetrated polymer network (IPN)-structured gels were designed with tunable elasticity, in which the extent of covalent crosslinking interactions is controlled by polymerization temperature ranging between −18 and 45 °C. Depending on the HyA content added in the synthesis and the polymerization temperature, the swelling ratio could be controlled. The addition of 0.05% (w/v) HyA increased the swelling of semi-IPNs, while the elastic modulus increased with increasing HyA content and decreased with the polymerization temperature. PAAm/PSA/HyA semi-IPNs showed the typical pH-sensitive swelling of anionic gels, and the swelling reached a maximum at a pH of 11.2. PAAm/PSA/HyA gels were tested for the removal of methyl violet from wastewater. Adsorption kinetics were shown to be well-fitted with the pseudo-second-order model using linear and nonlinear regression analysis. With the clear relationship between increased modulus and composition, this study enabled the fine-tuning of semi-IPN interactions by varying the polymerization temperature. [ABSTRACT FROM AUTHOR]

An acrylic acid-modified epoxy phosphate resin coating was synthesized by a four-step method marked "A-B-C-D", and it was used as an efficient protective layer for steel structures. The coating exhibited good properties, mainly including water resistance (≥240 h), salt spray resistance (≥300 h), surface drying time (≤1 h), and adhesion (≥6.5 MPa). [ABSTRACT FROM AUTHOR]

The corrosion resistance of cement–water-glass dual-liquid slurry is poor. Improving its material properties is necessary. In this study, we examined the influence of water-based lotions on the fluidity, gelling time, and mechanical properties of a cement–water-glass dual-liquid slurry based on the mix proportion of the dual-liquid slurry commonly used in construction. The mixture ratio of a C-S (cement–water-glass slurry) dual-liquid slurry was adjusted by introducing a waterborne polyurethane lotion and a waterborne acrylic lotion to modify the traditional C-S dual-liquid slurry material. When acrylic acid is used as a modifying polymer at a dosage of 7.5%, the flowability and gelation time of the dual-liquid slurry are excellent, the compressive strength of the stone body decreases slightly, the flexural strength is improved to a certain extent, and the stone body's crack resistance during water loss is also enhanced. Moreover, the porosity of the stone body is low. [ABSTRACT FROM AUTHOR]

In this paper, N-vinylpyrrolidone was copolymerized with acrylic acid and itaconic acid by free radical polymerization, and a series of polyacrylic acid-co-itaconic acid-co-N-vinylpyrrolidone (PAIN) dispersants with different pyrrolidone ligand contents were synthesized and characterized. Then, the cobalt blue nano-pigment slurry (20 wt%) was prepared through a water-based grinding method, and the optimum grinding technology was explored and determined as follows: PAIN2 as a dispersant, a dispersant dosage of 10 wt%, and a grinding time of 480 min. According to this optimum grinding technology, the prepared pigment slurry had a significantly decreased agglomeration, the D90 of which was 82 nm, and separately increased to 130 nm and 150 nm after heat storage for 3 and 7 days, exhibiting excellent heat storage stability. Additionally, its TSI value was also the lowest (1.9%), indicating good dispersion stability. The QCM and adorption capacity measuring results showed PAIN2 had a larger adsorption capacity, and the formed adsorption layer had a higher rigidity and was not easy to fall off. This was caused by both the interaction of carboxyl groups and the pyrrolidone ligand (strong coordination interaction) in PAIN2 with cobalt blue. The XPS and FT–IR measurements further proved the above-mentioned adsorption mechanism. [ABSTRACT FROM AUTHOR]

Photocatalytic membranes are crucial in addressing membrane fouling issues. However, the grafting amount of the catalyst on the membrane often becomes a key factor in restricting the membrane's self-cleaning capability. To address the challenge, this manuscript proposes a method for solving membrane fouling, featuring high grafting rates of bismuth oxide (Bi2O3) and acrylic acid (AA), significant contaminant degradation capability, and reusability. A highly photocatalytic self-cleaning microfiltration membrane made of polyvinylidene fluoride bismuth oxide and acrylic acid (PVDF-g-BA) was prepared by attaching nano Bi2O3 and acrylic acid onto the polyvinylidene fluoride membrane through adsorption/deposition and UV grafting polymerization. Compared with pure membranes and pure acrylic grafted membranes (PVDF-g-AA), the modified membrane grafted with 0.5% bismuth oxide not only improves the grafting rate and filtration performance, but also has higher self-cleaning ability. Furthermore, the degradation effect of this membrane on the organic dye methyl violet 2B under visible light irradiation is very significant, with a degradation rate reaching 90% and almost complete degradation after 12 h. Finally, after repeated filtration and photocatalysis, the membrane can still significantly degrade contaminants and can be reused. [ABSTRACT FROM AUTHOR]

Polyacrylamide (PAM) is a high-molecular-weight polymer with extensive applications. However, the inefficient natural degradation of PAM results in environmental accumulation of the polymer. Biodegradation is an environmentally friendly approach in the field of PAM treatment. The first phase of PAM biodegradation is the deamination of PAM, forming the product poly(acrylic acid) (PAA). The second phase of PAM biodegradation involves the cleavage of PAA into small molecules, which is a crucial step in the degradation pathway of PAM. However, the enzyme that catalyzes the degradation of PAA and the molecular mechanism remain unclear. Here, a novel monooxygenase PCX02514 is identified as the key enzyme for PAA degradation. Through biochemical experiments, the monooxygenase PCX02514 oxidizes PAA with the participation of NADPH, causing the cleavage of carbon chains and a decrease in the molecular weight of PAA. In addition, the crystal structure of the monooxygenase PCX02514 is solved at a resolution of 1.97 Å. The active pocket is in a long cavity that extends from the C-terminus of the TIM barrel to the protein surface and exhibits positive electrostatic potential, thereby causing the migration of oxygen-negative ions into the active pocket and facilitating the reaction between the substrates and monooxygenase PCX02514. Moreover, Arg10-Arg125-Ser186-Arg187-His253 are proposed as potential active sites in monooxygenase PCX02514. Our research characterizes the molecular mechanism of this monooxygenase, providing a theoretical basis and valuable tools for PAM bioremediation. [ABSTRACT FROM AUTHOR]

A new type of UV-curable pressure-sensitive adhesive containing Si atoms (Si-PSAs) was prepared by a solution-free UV-initiated telomerization process of n-butyl acrylate, acrylic acid, methyl methacrylate, and 4-acrylooxybenzophenone using triethylsilane (TES) as a telogen and an acylphosphine oxide (APO) as a radical photoinitiator. Selected commercial adhesion promoters were tested as additives in the formulation of adhesive compositions, i.e., (i) an organic copolymer with polar groups (carboxyl and hydroxyl); (ii) a hydroxymetal-organic compound; and (iii) a quaternary ammonium salt and (iv) a chlorinated polyolefin. No fillers, crosslinking agents, or photoinitiators were used in the adhesive compositions. NMR techniques confirmed the incorporation of silicon atoms into the polyacrylate structure. The influence of adhesion promoters on the kinetics of the UV-crosslinking process of Si-PSAs was investigated by a photo-DSC technique. The obtained Si-PSAs were characterized by adhesion (to steel, glass, PMMA, and PE), tack, and cohesion at 20 °C. Finally, the wetting angle of Si-PSAs with water was checked and their thermal stability was proved (TGA). Unexpectedly, the quaternary ammonium salt had the most favorable effect on improving the thermal stability of Si-PSAs (302 °C) and adhesion to glass and PMMA. In contrast, Si-PSAs containing the hydroxymetal-organic compound showed excellent adhesion to steel. [ABSTRACT FROM AUTHOR]

This study investigates the crosslinking dynamics and swelling properties of pH-responsive poly(ethylene glycol) (PEG)/poly(acrylic acid) (PAA) interpenetrating polymer network (IPN) hydrogels. These hydrogels feature denser crosslinked networks compared to PEG single network (SN) hydrogels. Fabrication involved a two-step UV curing process: First, forming PEG-SN hydrogels using poly(ethylene glycol) diacrylate (PEGDA) through UV-induced free radical polymerization and crosslinking reactions, then immersing them in PAA solutions with two different molar ratios of acrylic acid (AA) monomer and poly(ethylene glycol) dimethacrylate (PEGDMA) crosslinker. A subsequent UV curing step created PAA networks within the pre-fabricated PEG hydrogels. The incorporation of AA with ionizable functional groups imparted pH sensitivity to the hydrogels, allowing the swelling ratio to respond to environmental pH changes. Rheological analysis showed that PEG/PAA IPN hydrogels had a higher storage modulus (G′) than PEG-SN hydrogels, with PEG/PAA-IPN5 exhibiting the highest modulus. Thermal analysis via thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) indicated increased thermal stability for PEG/PAA-IPN5 compared to PEG/PAA-IPN1, due to higher crosslinking density from increased PEGDMA content. Consistent with the storage modulus trend, PEG/PAA-IPN hydrogels demonstrated superior mechanical properties compared to PEG-SN hydrogels. The tighter network structure led to reduced water uptake and a higher gel modulus in swollen IPN hydrogels, attributed to the increased density of active network strands. Below the pKa (4.3) of acrylic acid, hydrogen bonds between PEG and PAA chains caused the IPN hydrogels to contract. Above the pKa, ionization of PAA chains induced electrostatic repulsion and osmotic forces, increasing water absorption. Adjusting the crosslinking density of the PAA network enabled fine-tuning of the IPN hydrogels' properties, allowing comprehensive comparison of single network and IPN characteristics. [ABSTRACT FROM AUTHOR]

The indigo dye found in wastewater from printing and dyeing processes is potentially carcinogenic, teratogenic, and mutagenic, making it a serious threat to the health of animals, plants, and humans. Motivated by the growing need to remove indigo from wastewater, this study prepared novel fiber absorbents using melt-blow polypropylene (PP) melt as a matrix, as well as acrylic acid (AA) and maleic anhydride (MAH) as functional monomers. The modification conditions were studied to optimize the double-initiation, continuous-suspension grafting process, and then functional fibers were prepared by melt-blown spinning the modified PP. The results showed that the optimum modification conditions were as follows: a 3.5 wt% interfacial agent, 8 mg/L of dispersant, 80% monomer content, a 0.8 mass ratio of AA to MAH, a 1000 r/min stir speed, 3.5 wt% initiator DBPH grafting at 130 °C for 3 h, and 1 wt% initiator BPO grafting at 90 °C for 2 h. The highest grafting rate of the PP-g-AA-MAH was 31.2%, and the infrared spectrum and nuclear magnetic resonance spectroscopic analysis showed that AA and MAH were successfully grafted onto PP fiber. This modification strategy also made the fibers more hydrophilic. The adsorption capacity of the PP-g-AA-MAH fibers was highly dependent on pH, and the highest indigo adsorption capacity was 110.43 mg/g at pH 7. The fiber adsorption capacity for indigo increased rapidly before plateauing with increasing time or indigo concentration, and the experimental data were well described in a pseudo-second-order kinetic model and a Langmuir isothermal adsorption model. Most impressively, the modified fiber adsorption capacity for indigo remained as high as 91.22 mg/g after eight regeneration and reuse cycles. In summary, the PP-g-AA-MAH fibers, with excellent adsorption-desorption characteristics, could be readily regenerated and reused, and they are a promising material for the removal of indigo from wastewater. [ABSTRACT FROM AUTHOR]

The terpolymers of N-vinylpyrrolidone (VP) with acrylic acid and triethylene glycol methacrylate were synthesized with more than 90% yield by radical copolymerization in ethanol from monomeric mixtures of different molar composition (98:2:2, 95:5: 2 and 98:2:5) and their monomer composition, absolute molecular masses and hydrodynamic radii in aqueous media were determined. Using the MTT test, these terpolymers were established to be low toxic for non-tumor Vero cells and HeLa tumor cells. Polymer compositions of hydrophobic dye methyl pheophorbide a (MPP) based on studied terpolymers and linear polyvinylpyrrolidone (PVP) were obtained and characterized in water solution. Quantum-chemical modeling of the MPP-copolymer structures was conducted, and the possibility of hydrogen bond formation between terpolymer units and the MPP molecule was shown. Using fluorescence microscopy, the accumulation and distribution of polymer particles in non-tumor (FetMSC) and tumor (HeLa) cells was studied, and an increase in the accumulation of MPP with both types of particles was found. [ABSTRACT FROM AUTHOR]

A microwave technique was used to prepare a superabsorbent polymer (SAP) by grafting two hydrophilic monomers onto a polysaccharide substrate. The monomers used were acrylic acid (AA) or acrylamide (AM) and were grafted onto a pullulan (PUL) substrate to form PUL-g-AA (SAP1) and PUL-g-AM (SAP2), respectively. The monomers (AM/AA) were grafted together onto a PUL substrate to form PUL-g-(AM/AA) (SAP3). Grafting parameters such as grafting efficiency with the percentage, the conversion of monomer into polymer, gel content, water retention, water adsorption capacity, and swelling kinetics were determined. Additionally, the effect of environmental pH (2, 4, 7, 9, and 12) and sodium dodecylbenzene sulfonate (SDBS) surfactant was evaluated, where 1, 2, 3, 4, and 5 mM of SDBS was added to form SAP4 to SAP8. The FTIR results show that AM was grafted onto PUL through an aliphatic C-N bond, while AA grafting occurred through a single C-C bond. The grafting efficiency with AM was higher than with AA, as well as showing a superior gel content. Water absorbance capacity and water retention increased with the grafting of AA and AM together for SAP3. The highest absorbent capacity, water retention, gel content, and grafting parameters values were obtained with a 3 mM SDBS content and a pH of 7. The swelling kinetics showed that the increases in the theoretical and experimental swelling equilibriums were 72% and 82%, respectively, for SAP6 compared to the values of these parameters for SAP3. The water absorption capacity of the hydrogel increases upon increasing the pH to 7 and then gradually decreases. XRD demonstrated the improved crystallinity and crystalline size of the hydrogel after grafting polymerization of AM/AA onto PUL, in addition to enhanced thermal stability. On the contrary, FE-SEM demonstrated that SDBS improves the porosity and pore size of the hydrogel surface with SAP6. [ABSTRACT FROM AUTHOR]

In this study, a viscosity-reducing polycarboxylic acid superplasticizer (VRPCE) was synthesized using methylallyl polyoxyethylene ether (HPEG), acrylic acid (AA), and maltodextrin maleic acid monoester (MDMA) as the main raw materials. The influences of the VRPCE on the microscopic properties of cement paste were studied by gel permeation chromatography (GPC), total organic carbon test (TOC), zeta potential, laser particle size analysis, XRD, MIP, TG, and SEM. Finally, the effects of the VRPCE on the macroscopic properties of cement mortar were evaluated through flow time, slump flow, compressive strength, shrinkage, and creep. The results showed that the VRPCE can improve the hydration degree of the cement, optimize the pore structure, increase the porosity, improve the fluidity, compressive strength, and creep, and decrease the shrinkage resistance of the cement mortar. [ABSTRACT FROM AUTHOR]

The pH- and thermo-responsive behavior of polymeric hydrogels M C − c o − M A have been studied in detail using dynamic light scattering D L S , scanning electron microscopy   S E M , nuclear magnetic resonance (1H NMR) and rheology to evaluate the conformational changes, swelling–shrinkage, stability, the ability to flow and the diffusion process of nanoparticles at several temperatures. Furthermore, polymeric systems functionalized with acrylic acid M C and acrylamide M A were subjected to a titration process with a calcium chloride C a C l 2 solution to analyze its effect on the average particle diameter   D z , polymer structure and the intra- and intermolecular interactions in order to provide a responsive polymer network that can be used as a possible nanocarrier for drug delivery with several benefits. The results confirmed that the structural changes in the sensitive hydrogels are highly dependent on the corresponding critical solution temperature C S T of the carboxylic (–COOH) and amide (–CONH2) functional groups and the influence of calcium ions C a 2 + on the formation or breaking of hydrogen bonds, as well as the decrease in electrostatic repulsions generated between the polymer chains contributing to a particle agglomeration phenomenon. The temperature leads to a re-arrangement of the polymer chains, affecting the viscoelastic properties of the hydrogels. In addition, the diffusion coefficients D of nanoparticles were evaluated, showing a closeness among with the morphology, shape, size and temperature, resulting in slower diffusions for larger particles size and, conversely, the diffusion in the medium increasing as the polymer size is reduced. Therefore, the hydrogels exhibited a remarkable response to pH and temperature variations in the environment. During this research, the functionality and behavior of the polymeric nanoparticles were observed under different analysis conditions, which revealed notable structural changes and further demonstrated the nanoparticles promising high potential for drug delivery applications. Hence, these results have sparked significant interest in various scientific, industrial and technological fields. [ABSTRACT FROM AUTHOR]

In recent years, many researchers have focused on designing hydrogels with specific functional groups that exhibit high affinity for various contaminants, such as heavy metals, organic pollutants, pathogens, or nutrients, or environmental parameters. Novel approaches, including cross-linking strategies and the use of nanomaterials, have been employed to enhance the structural integrity and performance of the desired hydrogels. The evolution of these hydrogels is further highlighted, with an emphasis on fine-tuning features, including water absorption capacity, environmental pollutant/factor sensing and selectivity, and recyclability. Furthermore, this review investigates the emerging topic of stimuli-responsive smart hydrogels, underscoring their potential in both sorption and detection of water pollutants. By critically assessing a wide range of studies, this review not only synthesizes existing knowledge, but also identifies advantages and limitations, and describes future research directions in the field of chemically engineered hydrogels for water purification and monitoring with a low environmental impact as an important resource for chemists and multidisciplinary researchers, leading to improvements in sustainable water management technology. [ABSTRACT FROM AUTHOR]

This study aimed to develop composite hydrogels with exceptional piezoelectric properties and pressure sensitivity. To achieve the objective, this study created a deep eutectic solvent (DES) by mixing choline chloride (ChCl), acrylamide (AM), and acrylic acid (AA). Barium titanate nanoparticles (BTNPs) were incorporated as fillers into the deep eutectic solvents (DES) to synthesize the composite hydrogels using frontal polymerization (FP). The mechanical and piezoelectric properties of the resulting composite hydrogels were analyzed using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). This study found that the BTNPs/P(AM-co-AA) composite hydrogels exhibited excellent mechanical and piezoelectric properties. This is attributed to the high dielectric constant of BTNPs and the electrode polarization phenomenon when subjected to pressure. With a BTNPs content of 0.6 wt%, the maximum compressive strength increased by 3.68 times compared with the hydrogel without added BTNPs. Moreover, increasing the BTNPs content to 0.6 wt% resulted in a 1.48 times increase in generated voltage under the same pressure, compared with the hydrogel with only 0.2 wt% BTNPs. This study provides a method for preparing composite hydrogels with outstanding piezoelectric properties and pressure sensitivity. [ABSTRACT FROM AUTHOR]

The need to create safe materials for biomedical and pharmaceutical applications has become a significant driving force for the development of new systems. Therefore, a chitosan-coated copolymer of itaconic acid, acrylic acid, and N-vinyl caprolactam (IT-AA-NVC) was prepared by radical polymerization and subsequent coating via nanoprecipitation to give a system capable of sustained delivery of melatonin. Although melatonin brings undoubted benefits to the human body, aspects of the optimal dose, route, and time of administration for the obtaining of suitable treatment outcomes remain under discussion. The entrapment of melatonin in biocompatible polymeric systems can prevent its oxidation, decrease its toxicity, and provide an increased half-life, resulting in an enhanced pharmacokinetic profile with improved patient compliance. The structures of the biopolymer and conjugate were proven by FTIR, thermal properties were tested by DSC, and the morphologies were followed by SEM. The loading efficiency and in vitro release profile were studied by means of HPLC, and a delayed release profile with an initial burst was obtained. The potential systemic toxicity of the formulation was studied in vivo; a mild hepatotoxicity was observed following administration of the melatonin-loaded formulation to mice, both by histopathology and blood clinical biochemistry. Histopathology showed a mild nephrotoxicity as well; however, kidney clinical biochemistry did not support this. [ABSTRACT FROM AUTHOR]

In our study, using chromatographic techniques, we isolated three bioactive compounds, which were structurally elucidated as (E)-2-(3-(3,4-dimethoxyphenyl)acrylamido)-N-methylbenzamide (1), 4-Hydroxyquinoline-2-carboxylic acid (2), and (E)-2-Cyano-3-(4-hydroxyphenyl)acrylic acid (3), using spectroscopic methods. The anti-melanogenic, anti-inflammatory, antioxidant, and anti-aging properties were evaluated in vitro by measuring the activity of pharmacological targets including tyrosinase, melanin, NF-κB, hyaluronidase, elastase, collagenase, and Nrf2. Our results show that compound 1 is the most active with IC50 values of 14.19 μM (tyrosinase inhibition), 22.24 μM (melanin inhibition), 9.82–12.72 μM (NF-κB inhibition), 79.71 μM (hyaluronidase inhibition), 80.13 μM (elastase inhibition), 76.59 μM (collagenase inhibition), and 116–385 nM (Nrf2 activation) in the THP-1, HEK001, WS1, and HMCB cells. These findings underscore the promising profiles of the aqueous extract of R. urticifolius at safe cytotoxic concentrations. Additionally, we report, for the first time, the isolation and characterisation of these nitrogenous compounds in the R. urticifolius species. Finally, compound 1, isolated from R. urticifolius, is a promising candidate for the development of more effective and safer compounds for diseases related to skin pigmentation, protection against inflammation, and oxidative stress. [ABSTRACT FROM AUTHOR]

The quest for sustainable and functional food packaging materials has led researchers to explore biopolymers such as pullulan, which has emerged as a notable candidate for its excellent film-forming and anti-fogging properties. This study introduces an innovative anti-fog coating by combining pullulan with poly (acrylic acid sodium salt) to enhance the display of packaged food in high humidity environments without impairing the sealing performance of the packaging material—two critical factors in preserving food quality and consumers' acceptance. The research focused on varying the ratios of pullulan to poly (acrylic acid sodium salt) and investigating the performance of this formulation as an anti-fog coating on bioriented polypropylene (BOPP). Contact angle analysis showed a significant improvement in BOPP wettability after coating deposition, with water contact angle values ranging from ~60° to ~17° for formulations consisting only of poly (acrylic acid sodium salt) (P0) or pullulan (P100), respectively. Furthermore, seal strength evaluations demonstrated acceptable performance, with the optimal formulation (P50) achieving the highest sealing force (~2.7 N/2.5 cm) at higher temperatures (130 °C). These results highlight the exceptional potential of a pullulan-based coating as an alternative to conventional packaging materials, significantly enhancing anti-fogging performance. [ABSTRACT FROM AUTHOR]

Highlights: Plasma-grafting acrylic acid composite membrane for MABR was prepared. Higher O2 transfer rate and better hydrophilicity for modified membranes than pristine. Modified PVDF membrane demonstrated superior nitrogen removal during startup. Activity of denitrifying bacteria was enhanced in the modified PVDF MABR. Microporous membranes such as polytetrafluoroethylene (PTFE) and polyvinylidene fluoride (PVDF) often exhibit suboptimal hydrophilicity and microbial adhesion, which impede effective nitrogen removal in membrane-aerated biofilm reactors (MABRs), particularly during initial operational phases. To address this issue, the present study introduced acrylic acid (AA) following plasma treatment (P) to enhance membrane performance, thereby engineering a novel composite material optimized for MABR applications. Four MABRs—Reactor with pristine PVDF membrane (R-PVDF), Reactor with composite PVDF membrane (R-PVDF-P-AA), Reactor with pristine PTFE membrane (R-PTFE), and Reactor with composite PTFE membrane (R-PTFE-P-AA)—were evaluated. The modified membranes displayed enhanced roughness and hydrophilicity, which improved biocompatibility and variably increased the oxygen transfer efficiency. Notably, the R-PVDF-P-AA configuration showed a significant enhancement in the removal rates of NH4+-N and total nitrogen (TN), achieving 78.5% and 61.3%, respectively, which was markedly higher than those observed with the original membranes. In contrast, the modified R-PTFE-P-AA exhibited lower removal efficiencies, with NH4+-N and TN reductions of approximately 60.0% and 49.5%. Detailed microbial community analysis revealed that the R-PVDF-P-AA membrane supported robust commensalism between ammonia-oxidizing and denitrifying bacteria, underpinning the improved performance. These findings highlight the critical role of surface chemistry and microbial ecology in optimizing the function of MABRs. [ABSTRACT FROM AUTHOR]

The new hybrid composite materials for PEM fuel cell were synthesized by the UV polymerization of acrylic monomers (acrylonitrile, acrylic acid, ethylene glycol dimethacrylate) and a sulfo aromatic monomer, i.e., sodium styrene sulfonate, and the tetraethoxysilane/3-methacryloxypropyltrimethoxysilane-based sol–gel system. By means of X-ray spectroscopy, the fractal structure of the obtained materials was characterized. Proton conductivity and viscoelasticity of the obtained materials were determined depending on the content of the inorganic component in nanocomposites. Based on impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite's electrolyte membranes. [ABSTRACT FROM AUTHOR]

The swelling behaviors and water retention of superabsorbent sand-fixing materials prepared from acrylic acid/acrylamide copolymer (AA/AM) and acid-modified attapulgite under ultrasonic treatments and different pH conditions were investigated. The results demonstrated that a suitable amount of attapulgite can effectively improve the absorption capacity and saltwater performance. The superabsorbent achieved the highest absorptions of 1257.54 g/g and 209.45 g/g in distilled water and a 0.9 wt% NaCl solution, and a higher water absorbency occurred over a wide pH range of 5~9 when the ultrasonic power was 200 W and the attapulgite content was 10%. The addition of attapulgite could significantly increase the water absorption and retention. [ABSTRACT FROM AUTHOR]

Cancer immunotherapy using antigen-pulsed dendritic cells can induce strong cellular immune responses by priming cytotoxic T lymphocytes. In this study, we pulsed tumor cell lysates with VP-R8, a cell-penetrating D-octaarginine-linked co-polymer of N-vinylacetamide and acrylic acid (PNVA-co-AA), into the DC2.4 murine dendritic cell line to improve antigen uptake and then determined the anti-tumor effect in tumor-bearing mice. DC2.4 cells were pulsed with the cell lysate of EL4, a murine lymphoma cell line, and VP-R8 to generate the DC2.4 vaccine. For the in vivo study, DC2.4 cells pulsed with EL4 lysate and VP-R8 were subcutaneously injected into the inguinal lymph node to investigate the anti-tumor effect against EL4 and EL4-specific T cell immune responses. VP-R8 significantly improved antigen uptake into DC2.4 compared to conventional keyhole limpet hemocyanin (p < 0.05). The expression of MHC class I, MHC class II, and CD86 in DC2.4 cells significantly increased after pulsing tumor lysates with VP-R8 compared to other treatments (p < 0.05). The intra-lymph node injection of DC2.4 pulsed with both VP-R8 and EL4 lysate significantly decreased tumor growth compared to DC2.4 pulsed with KLH and lysates (p < 0.05) and induced tumor-infiltrating CD8T cells. The DC2.4 vaccine also remarkably increased the population of IFN-gamma-producing T cells and CTL activity against EL4 cells. In conclusion, we demonstrated that VP-R8 markedly enhances the efficiency of dendritic cell-based vaccines in priming robust anti-tumor immunity, suggesting its potential as a beneficial additive for dendritic cell-based immunotherapy. [ABSTRACT FROM AUTHOR]

Nanoparticles composed of inorganic boron-containing compounds represent a promising candidate as 10B carriers for BNCT. This study focuses on the synthesis, characterization, and assessment of the biological activity of composite nanomaterials based on boron carbide (B4C). Boron carbide is a compelling alternative to borated molecules due to its high volumetric B content, prolonged retention in biological systems, and low toxicity. These attributes lead to a substantial accumulation of B in tissues, eliminating the need for isotopically enriched compounds. In our approach, B4C nanoparticles were included in composite nanostructures with ultrasmall superparamagnetic nanoparticles (SPIONs), coated with poly (acrylic acid), and further functionalized with the fluorophore DiI. The successful internalization of these nanoparticles in HeLa cells was confirmed, and a significant uptake of 10B was observed. Micro-distribution studies were conducted using intracellular neutron autoradiography, providing valuable insights into the spatial distribution of the nanoparticles within cells. These findings strongly indicate that the developed nanomaterials hold significant promise as effective carriers for 10B in BNCT, showcasing their potential for advancing cancer treatment methodologies. [ABSTRACT FROM AUTHOR]

Faced with higher demands of pigments in various applications, the performance of pigments in a specific system is in urgent need of optimization and improvement. Polyorganosiloxane (POS) stands out among various encapsulating polymeric materials for pigment modification due to its superior thermal stability and alkali resistance. However, the inherent hydrophobicity of POS causes poor stability in aqueous systems, which is usually applied in environmentally friendly applications. Grafting hydrophilic polymer chains on the surface of POS could improve water dispersity. In addition, the encapsulated pigment can also be endowed with various functionalities by selecting or combining grafted polymers. Herein, we reported a strategy to encapsulate Prussian blue (PB27) with POS grafted with poly(acrylic acid) (PAA) or poly(N-(2-hydroxyethyl) acrylamide) (PHEAA) to allow better stability and functionality of the composite pigment particles, denoted as PB27@POS@PAA or PB27@POS@PHEAA, respectively. The effect of the number of monomers and the amount of initiator potassium persulfate (KPS) on the brush thickness of the grafted polymers was studied, along with various performance properties and the functionality of PB27@POS@PAA and PB27@POS@PHEAA. The dispersity, alkali resistance, and high-temperature stability are studied. The brush-like composite pigment performs better after centrifugation (5000 rpm, 30 min) or treatment under 90 °C when the dosage of grafting monomer AA or HEAA reaches 400 wt%. Optimal alkali resistance was obtained for PB27@POS@PAA (AA, 200 wt%) with a particle size variation of only 31 nm after 8 h. Comparably, PB27@POS@PHEAA behaved worse under similar conditions. Moreover, PB27@POS grafted with PAA was responsive to pH and that with PHEAA showed excellent antifouling properties, which could also be replaced by other functional monomers if needed. [ABSTRACT FROM AUTHOR]

Levodopa (LD) has been the most efficacious medication and the gold standard therapy for Parkinson's disease (PD) for decades. However, its long-term administration is usually associated with motor complications, which are believed to be the result of the fluctuating pharmacokinetics of LD following oral administration. Duodopa® is the current option to offer a continuous delivery of LD and its decarboxylase inhibitor carbidopa (CD); however, its administration involves invasive surgical procedures, which could potentially lead to lifelong complications, such as infection. Recently, dissolving microarray patches (MAPs) have come to the fore as an alternative that can bypass the oral administration route in a minimally invasive way. This work explored the potential of using dissolving MAPs to deliver LD and CD across the skin. An acidic polymer poly(acrylic acid) (PAA) was used in the MAP fabrication to prevent the potential oxidation of LD at neutral pH. The drug contents of LD and CD in the formulated dissolving MAPs were 1.82 ± 0.24 and 0.47 ± 0.04 mg/patch, respectively. The in vivo pharmacokinetic study using female Sprague–Dawley® rats (Envigo RMS Holding Corp, Bicester, UK) demonstrated a simultaneous delivery of LD and CD and comparable AUC values between the dissolving MAPs and the oral LD/CD suspension. The relative bioavailability for the dissolving MAPs was calculated to be approximately 37.22%. Accordingly, this work highlights the use of dissolving MAPs as a minimally invasive approach which could potentially bypass the gastrointestinal pathway and deliver both drugs continuously without surgery. [ABSTRACT FROM AUTHOR]

Reppe carbonylation of acetylene is an atom-economic and non-petroleum approach to synthesize acrylic acid and acrylate esters, which are key intermediates in the textile, leather finishing, and polymer industries. In the present work, a noble metal-free Co@SiO2 catalyst was prepared and evaluated in the methoxycarbonylation reaction of acetylene. It was discovered that pretreatment of the catalyst by different reductants (i.e., C2H2, CO, H2, and syngas) greatly improved the catalytic activity, of which Co/SiO2-H2 demonstrated the best performance under conditions of 160 °C, 0.05 MPa C2H2, 4 MPa CO, and 1 h, affording a production rate of 4.38 gMA+MP gcat−1 h−1 for methyl acrylate (MA) and methyl propionate (MP) and 0.91 gDMS gcat−1 h−1 for dimethyl succinate (DMS), respectively. Transmission electron microscopy (TEM), X-ray diffraction (XRD), and diffuse reflectance infrared Fourier transform spectra of CO adsorption (CO-DRIFTS) measurements revealed that an H2 reduction decreased the size of the Co nanoparticles and promoted the formation of hollow architectures, leading to an increase in the metal surface area and CO adsorption on the catalyst. The hot filtration experiment confirmed that Co2(CO)8 was generated in situ during the reaction or at the pre-activation stage, which served as the genuine active species. Our work provides a facile and convenient approach to the in situ synthetization of Co2(CO)8 for a Reppe carbonylation reaction. [ABSTRACT FROM AUTHOR]

Hydrogels based on sodium alginate (SA) and partially neutralised poly(acrylic acid) were obtained by radical polymerisation. The hydrogels were cross-linked with N,N′-methylenebisacrylamide (MBA), simultaneously grafting the resulting polymer onto SA. The findings of the FTIR spectroscopy showed that all of the hydrogels were effectively synthesized and sodium alginate was chemically bonded with the poly(sodium acrylate) matrix. DSC analysis of the melting heat and glass transition parameters indicated that the hydrogel structure had changed as a result of the cross-linking process. Sodium alginate and MBA were tested at different concentrations to determine how they affected the hydrogel properties. A very high content of the biopolymer, i.e., sodium alginate, was used in our research, up to 33 wt%. This resulted in durable and stable hydrogels with a very high ability to uptake water, comparable to hydrogels based on synthetic polymers only. The ability to swell is inversely proportional to the quantity of MBA present. By increasing the amount of sodium alginate in the hydrogel, the ability of the hydrogel to absorb water is reduced. However, water uptake remains relatively high at 350 g·g−1, even for the hydrogel with the highest SA content. [ABSTRACT FROM AUTHOR]

Attapulgite-hydroxyethyl cellulose-poly (acrylic acid-co-2-acrylamide-2-methylpropanesulfonic acid) (ATP-HEC-P(AA-co-AMPS)) in-concrete curing material was synthesized by aqueous solution polymerization using attapulgite (ATP) as an inorganic filler and hydroxyethyl cellulose (HEC) as a backbone. The effects of relevant factors such as ATP dosage, HEC dosage, degree of neutralization, initiator quality, and cross-linking agent quality on the water absorption characteristics of ATP-HEC-P (AA-co-AMPS) were investigated through expansion tests. The micro-morphology of ATP-HEC-P (AA-co-AMPS) was also comprehensively characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, a thermal analysis, and other applicable means. The results showed that the prepared ATP-HEC-P (AA-co-AMPS) had a strong water absorption and water retention capacity, with a water absorption multiplicity of 382 g/g in deionized water and 21.55% water retention capacity after being placed at room temperature for 7 d in a bare environment. Additionally, ATP-HEC-P (AA-co-AMPS) showed good performance for absorbing liquids within the pH range of 7–12. The material's thermal stability and mechanical properties were also significantly improved after the addition of ATP. The preparation cost is low, the process is simple, and the material meets the requirements for concrete curing materials. [ABSTRACT FROM AUTHOR]

This paper focuses on the preparation and evaluation of a novel humidity-control material, vermiculite/(sodium polyacrylate(AA)–acrylamide(AM)), using inverse suspension polymerization. Acrylic acid and acrylamide were introduced into the interlayer of modified vermiculite during the polymerization process, leading to the formation of a strong association with the modified vermiculite. The addition of vermiculite increased the specific surface area and pore volume of the composites. To investigate the moisture absorption and desorption properties of the composites, an orthogonal experiment and single-factor experiment were conducted to analyze the impacts of vermiculite content, neutralization degree, and the mass ratio of AA to AM. According to the control experiment, the addition of vermiculite was found to enhance the pore structure and surface morphology of the composite material, surpassing both vermiculite and PAA-AM copolymer in terms of humidity control capacity and rate. The optimal preparation conditions were identified as follows: vermiculite mass fraction of 4 wt%, a neutralization degree of 90%, and mAA:mAM = 4:1. The moisture absorption rate and moisture release rate of the composite material prepared under these conditions are 1.285 g/g and 1.172 g/g. The humidity control process of the composite material is governed by pseudo second-order kinetics, which encompasses the complete adsorption process. These results indicate that the vermiculite/PAA-AM composite humidity control material has excellent humidity control performance and is a simple and efficient humidity control method. [ABSTRACT FROM AUTHOR]

The ATP-BF-P(HEC-AA-AMPS) composite highly absorbent polymer was copolymerized with acrylic acid (AA) and 2-acrylamido-2-methylpropane sulfonic acid (AMPS) using an aqueous solution method with attapulgite (ATP) and attapulgite (ATP) as a matrix. The prepared ATP-BF-P(HEC-AA-AMPS) was characterized in terms of microstructure and tested for its water absorption capacity, water retention properties, and pH dynamic sensing ability. The results showed that the synthesized ATP-BF-P(HEC-AA-AMPS) had a rough and porous surface and a high water absorption capacity and rate, almost reaching the maximum water absorption around 20 min, and demonstrated excellent water retention performance at low and medium temperatures. ATP-BF-P(HEC-AA-AMPS) has a sensitive dynamic sensing ability in different pH solutions, with a high swelling capacity between pH 6.0 and 10.0. When the pH value exceeded 10.0, the swelling rate decreased rapidly. Additionally, the thermal stability and mechanical strength of the highly absorbent polymers were significantly improved after blending with ATP and BF. [ABSTRACT FROM AUTHOR]

Natural and synthetic polymers are a versatile platform for developing biomaterials in the biomedical and environmental fields. Natural polymers are organic compounds that are found in nature. The most common natural polymers include polysaccharides, such as alginate, hyaluronic acid, and starch, proteins, e.g., collagen, silk, and fibrin, and bacterial polyesters. Natural polymers have already been applied in numerous sectors, such as carriers for drug delivery, tissue engineering, stem cell morphogenesis, wound healing, regenerative medicine, food packaging, etc. Various synthetic polymers, including poly(lactic acid), poly(acrylic acid), poly(vinyl alcohol), polyethylene glycol, etc., are biocompatible and biodegradable; therefore, they are studied and applied in controlled drug release systems, nano-carriers, tissue engineering, dispersion of bacterial biofilms, gene delivery systems, bio-ink in 3D-printing, textiles in medicine, agriculture, heavy metals removal, and food packaging. In the following review, recent advancements in polymer chemistry, which enable the imparting of specific biomedical functions of polymers, will be discussed in detail, including antiviral, anticancer, and antimicrobial activities. This work contains the authors' experimental contributions to biomedical and environmental polymer applications. This review is a vast overview of natural and synthetic polymers used in biomedical and environmental fields, polymer synthesis, and isolation methods, critically assessessing their advantages, limitations, and prospects. [ABSTRACT FROM AUTHOR]

A novel hyperbranched polymer with polyacrylamide side chains (HAPAM) was synthesized by aqueous solution polymerization using acrylic acid, acrylamide, 2-acrylamido-2-methyl-1-propanesulfonic acid, hydrophobic monomer of dimethyl octadecyl ammonium chloride, and the homemade skeleton monomer of modified-M2.0 as raw materials and (NH4)2S2O8-NaHSO3 as initiator. The molecular structure, functional groups, and surface morphology of HAPAM were characterized by Fourier transform infrared spectroscopy, nuclear magnetic resonance hydrogen spectroscopy, and scanning electron microscopy. It was found that the performance of HAPAM solution was higher than that of ordinary polyacrylamide solution in terms of thickening ability, shearing resistance, thermal endurance, salt-resistance, resistance-coefficient and residual-resistance-coefficient, ability to reduce interfacial tension between polymer solution and crude oil, and oil-displacement-efficiency. In particular, the enhanced oil recovery of the HAPAM solution was 13.03%, and the improvement of shearing resistance and immunity to chromatographic separation were simultaneously achieved by the HAPAM solution. These results indicate that the successful synthesis of the novel HAPAM opens a promising strategy for developing new high-performance oil-displacing polymers. [ABSTRACT FROM AUTHOR]

Waterborne acrylic coatings, the largest market share of predominant environmentally friendly coatings, face limitations in their extensive application due to their flammability. The flame-retardant properties of the coatings could be significantly enhanced by incorporate inorganic flame retardants. However, inorganic flame retardants tend to aggregate and unevenly disperse in waterborne acrylic coatings, causing a substantial decrease in flame retardancy. In this work, sodium silicate was utilized as a flame retardant, with urea and melamine serving as modifiers and synergistic agents. This combination resulted in the preparation of a sodium silicate/urea/melamine ternary synergistic waterborne acrylic flame-retardant coating. This coating was applied to the surface of poplar veneer to create flame-retardant poplar veneer. Subsequently, various instruments, including a scanning electron microscope (SEM), a limiting oxygen index meter (LOI), a thermogravimetric analyzer (TG), and a cone calorimeter (CONE), were employed to investigate the relevant properties and mechanisms of both the flame-retardant coating and poplar veneer. The results demonstrated that the sodium silicate/urea/melamine ternary synergistic flame retardant did not exhibit aggregation and could be uniformly dispersed in waterborne acrylic coatings. The physical and mechanical properties of the ternary synergistic flame-retardant poplar veneer coating were satisfactory. Melamine and urea, acting as modifiers, not only greatly enhanced the dispersibility of sodium silicate in waterborne acrylic coatings, but also assisted in the formation of a silicon-containing char layer through the generation of nitrogen, achieving ternary synergistic flame retardancy. In conclusion, this work explores a novel method to efficiently and uniformly disperse inorganic flame retardants in organic coatings. It significantly improves the dispersibility and uniformity of inorganic flame retardants in organic polymers, thereby substantially enhancing the flame-retardant performance of coatings. This work provides a theoretical basis for the research and application of new flame-retardant coatings in the field of chemistry and materials. [ABSTRACT FROM AUTHOR]

Polyacrylic acid (PAA), an organic chemical, has been used as an intermediate in the manufacture of pharmaceuticals and cosmetics. It has been suggested recently that PAA has a high pulmonary inflammatory and fibrotic potential. Although endoplasmic reticulum stress is induced by various external and intracellular stimuli, there have been no reports examining the relationship between PAA-induced lung injury and endoplasmic reticulum stress. F344 rats were intratracheally instilled with dispersed PAA (molecular weight: 269,000) at low (0.5 mg/mL) and high (2.5 mg/mL) doses, and they were sacrificed at 3 days, 1 week, 1 month, 3 months and 6 months after exposure. PAA caused extensive inflammation and fibrotic changes in the lungs' histopathology over a month following instillation. Compared to the control group, the mRNA levels of endoplasmic reticulum stress markers Bip and Chop in BALF were significantly increased in the exposure group. In fluorescent immunostaining, both Bip and Chop exhibited co-localization with macrophages. Intratracheal instillation of PAA induced neutrophil inflammation and fibrosis in the rat lung, suggesting that PAA with molecular weight 269,000 may lead to pulmonary disorder. Furthermore, the presence of endoplasmic reticulum stress in macrophages was suggested to be involved in PAA-induced lung injury. [ABSTRACT FROM AUTHOR]

This study investigated the effect of copper (Cu) doping content on zinc oxide with varied weight percentages and the dispersion of Cu-doped ZnO (CZO) by adding polyvinylpyrrolidone (PVP), coated on a glass substrate, through a physical assessment and optical property and thermal insulation testing. CZO NPs were synthesized by using the sol–gel method with a zinc acetate precursor. The powder X-ray diffraction (XRD) patterns of the CZO showed that the solid solubility limit was below 5 mol% without a secondary phase. A field-emission scanning electron microscopy (FE-SEM) micrograph demonstrated that the particle size of CZO was in nanoscale with the packing of a quasi-spherical shape. The UV-Vis-NIR reflectance spectra of the powder showed that 1 mol% CZO has the highest near-infrared (NIR) reflectivity in the wavelength 780–2500 nm, with great visible light transmission. The CZO NPs were loaded in acrylic copolymer in different weight percentages ranging from 25 wt% to 75 wt%, the film thickness of the coating was varied from 5 µm to 100 µm, and PVP was added into this nanocomposite polymer to disperse through an ultrasonication method. The results showed that the highest loading of CZO powder in a polymer at 75 wt% in 100 µm of thickness with polyvinylpyrrolidone (PVP) as a dispersant showed better sample dispersion and retained good transparency to the naked eye. [ABSTRACT FROM AUTHOR]

Hydrogel polymer electrolytes (GPEs), as an important component of flexible energy storage devices, have gradually received wide attention compared with traditional liquid electrolytes due to their advantages of good mechanical, bending, and safety properties. In this paper, two cross-linked GPEs of poly(acrylic acid-co-acrylamide) or poly(acrylic acid-co-N-methylolacrylamide) with NaNO3 aqueous solution (P(AA-co-AM)/NaNO3 or P(AA-co-HAM)/NaNO3) were successfully prepared using radical polymerization, respectively, using acrylic acid (AA) as the monomer, N-methylolacrylamide (HAM) or acrylamide (AM) as the comonomer, and N, N-methylenebisacrylamide (MBAA) as the cross-linking agent. We investigated the morphology, glass transition temperature (Tg), ionic conductivities, mechanical properties, and thermal stabilities of the two GPEs. By comparison, P(AA-co-HAM)/NaNO3 GPE exhibits a higher ionic conductivity of 2.00 × 10−2 S/cm, lower Tg of 152 °C, and appropriate mechanical properties, which are attributed to the hydrogen bonding between the -COOH and -OH, and moderate cross-linking. The flexible symmetrical supercapacitors were assembled with the two GPEs and two identical activated carbon electrodes, respectively. The results show that the flexible supercapacitor with P(AA-co-HAM)/NaNO3 GPE shows good electrochemical performance with a specific capacitance of 63.9 F g−1 at a current density of 0.2 A g−1 and a capacitance retention of 89.4% after 3000 charge–discharge cycles. Our results provide a simple and practical design strategy of GPEs for flexible supercapacitors with wide application prospects. [ABSTRACT FROM AUTHOR]

In tissue engineering (TE), the support structure (scaffold) plays a key role necessary for cell adhesion and proliferation. The protein constituents of the extracellular matrix (ECM), such as collagen, its derivative gelatine, and elastin, are the most attractive materials as possible scaffolds. To improve the modest mechanical properties of gelatine, a strategy consists of crosslinking it, as naturally occurs for collagen, which is stiffened by the oxidative action of lysyl oxidase (LO). Here, a novel protocol to crosslink gelatine has been developed, not using the commonly employed crosslinkers, but based on the formation of imine bonds or on aldolic condensation reactions occurring between gelatine and properly synthesized copolymers containing amine residues via LO-mediated oxidation. Particularly, we first synthesized and characterized an amino butyl styrene monomer (5), its copolymers with dimethylacrylamide (DMAA), and its terpolymer with DMAA and acrylic acid (AA). Three acryloyl amidoamine monomers (11a–c) and their copolymers with DMAA were then prepared. A methacrolein (MA)/DMAA copolymer already possessing the needed aldehyde groups was finally developed to investigate the relevance of LO in the crosslinking process. Oxidation tests of amine copolymers with LO were performed to identify the best substrates to be used in experiments of gelatine reticulation. Copolymers obtained with 5, 11b, and 11c were excellent substrates for LO and were employed with MA/DMAA copolymers in gelatine crosslinking tests in different conditions. Among the amine-containing copolymers, that obtained with 5 (CP5/DMMA-43.1) afforded a material (M21) with the highest crosslinking percentage (71%). Cytotoxicity experiments carried out on two cell lines (IMR-32 and SH SY5Y) with the analogous (P5) of the synthetic constituent of M21 (CP5/DMAA) had evidenced no significant reduction in cell viability, but proliferation promotion, thus establishing the biocompatibility of M21 and the possibility to develop it as a new scaffold for TE, upon further investigations. [ABSTRACT FROM AUTHOR]

The studies aimed to test the adsorption capacity of two silica-enriched porous materials, synthetic Na-X zeolite and Mn-containing carbon composite, towards Pb(II) and Zn(II) ions in single and mixed systems and in the presence of diclofenac (DCF) and (or) poly(acrylic acid) (PAA). The synthetic zeolite was characterized by a well-developed surface area of 728 m2/g and a pore diameter of 1.73 nm, while the carbon composite exhibited 268 m2/g and 7.37 nm, respectively. Na-X was found to be more efficient than the carbon composite (75–212 mg/g) in adsorbing heavy metal ions in both single and bimetallic systems (322–333 mg/g). In turn, the C/Mn/SiO2 composite was more effective in removing Pb(II) ions from the systems that simultaneously contained DCF or PAA (480 and 476 mg/g, respectively). The Na-X zeolite demonstrated the greatest stability in all the systems studied. The highest stability was observed in the DCF + Pb(II) mixture, in contrast to the carbon composites where the stability was much lower. To evaluate the possibility of regeneration of the solids, HCl proved to be the best desorbent for heavy metal ions (efficiency of 99%). In general, both adsorbents offer promising potential for solving environmental problems. [ABSTRACT FROM AUTHOR]

This article presents a thorough investigation into the synthesis of trimethylolpropane triacrylate (TMPTA) via the esterification reaction of trimethylolpropane (TMP) with acrylic acid using Amberlite™ 120 IR (H+), Amberlyst® 15, and Dowex™ 50WX8 resins as heterogeneous catalysts. Preliminary comparative tests explored the impact of air flow on water removal during the reaction and different acid-to-alcohol molar ratios (3:1, 6:1, or 9:1 mol:mol). The findings revealed that introducing air significantly enhances TMPTA yield and -OH group conversion, particularly at a 6:1 acid-to-alcohol molar ratio. Based on cost considerations, Amberlite™ 120 IR (H+) was selected as the preferred catalyst for further optimization. This included evaluating the effect of catalyst loading (10%, 5.0%, and 2.5% w/wtot) and assessing the impact of a pre-drying process on resin efficiency. The study concluded that optimal conditions did not necessitate drying, requiring 120 °C, a catalyst loading of 10% w/wtot, a 4 h reaction time, an acid:alcohol ratio of 6:1 mol:mol, the presence of MEHQ (0.1% mol/molAA), and air bubbling at 6 ± 1 Nl/h. Catalyst recycling was effectively implemented with a slight reduction in catalytic activity over consecutive runs. Furthermore, the study explored a scaled-up system with a mechanical stirrer, demonstrating the potential for multi-hundred grams scale-up. Considerations for optimizing the air flow stripping system are also highlighted. In summary, this study provides valuable insights into designing and optimizing the esterification process for TMPTA synthesis, laying the foundation for potential industrial applications. [ABSTRACT FROM AUTHOR]

Activated carbons obtained via the thermochemical treatment of lemon balm and mint herbs were applied for ionic polymers adsorption, which directly affects the stability of these types of aqueous suspensions. The examined carbonaceous materials were characterized by well-developed specific surface area (approximately 1000 m2/g) and mesoporous structure. The adsorbed amounts of anionic poly(acrylic acid) and cationic polyethyleneimine from one-component solutions reached significant levels, but the efficiency of adsorption of these compounds from binary solutions slightly decreased. Moreover, the ionic polymers showed stabilizing properties towards the activated carbons suspensions. For both adsorbents, the most stable suspensions were systems containing both types of polymeric macromolecules with different ionic characters. This was due to the occurrence of electrosteric and depletion stabilization mechanisms. Furthermore, the zeta potential and size of particle aggregates were also influenced by the presence of polymers in the aqueous suspensions of activated carbons. [ABSTRACT FROM AUTHOR]

The development of polymeric biocomposites containing natural fibers has grown over the years due to the properties achieved and its eco-friendly nature. Thus, biocomposites involving a polymer from a renewable source (Biopolyethylene (BioPE)) and babassu fibers (BFs), compatibilized with polyethylene grafted with maleic anhydride (MA) and acrylic acid (AA) (PE-g-MA and PE-g-AA, respectively) were obtained using melt mixing and injection molded into tensile, impact, and HDT specimens. Babassu fiber was characterized with Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TGA), and scanning electron microscopy (SEM). The biocomposites were characterized using torque rheometry, TGA, tensile strength, impact strength, thermomechanical properties, Shore D hardness, and SEM. The data indicate that the torque during the processing of compatibilized biocomposites was higher than that of BioPE/BF biocomposites, which was taken as an indication of a possible reaction between the functional groups. Compatibilization led to a substantial improvement in the elastic modulus, tensile strength, HDT, and VST and a decrease in Shore D hardness. These results were justified with SEM micrographs, which showed babassu fibers better adhered to the surface of the biopolyethylene matrix, as well as an encapsulation of these fibers. The system investigated is environmentally sustainable, and the results are promising for the technology of polymeric composites. [ABSTRACT FROM AUTHOR]

Amphiphilic block copolymers-based aqueous color inks show great potential in the field of visual communication design. However, the conventional step-by-step chemistry employed to synthesize the amphiphilic block copolymers is intricate, with low yield and high economic and environmental costs. In this work, we present a novel method for preparing an amphiphilic AB di-block copolymer of PCL-b-PAA by employing a combined polymerization strategy that involves both cationic ring-opening polymerization (ROP) of the ε-caprolactone monomer and the reversible addition–fragmentation chain-transfer (RAFT) polymerization on the acrylic acid monomer simultaneously. The corresponding polycaprolactone (PCL) and polyacrylic acid (PAA) serve as the hydrophobic and hydrophilic units, respectively. The effectiveness of the amphiphilic AB di-block copolymer as the polymeric pigment dispersant for water-based color inks is evaluated. The amphiphilic AB di-block copolymer of PCL-b-PAA exhibits a molecular weight of 1400 g mol−1, which is consistent with the theoretical value and suitable for polymeric dispersant application. The high surface excess (Γmax) of the PCL-b-PAA in water indicates a densely packed molecular morphology at the water/air interface. Additionally, micelles can be stably formed in the aqueous PCL-b-PAA solution at very low concentrations by demonstrating a low CMC value of 10−4 wt% and a micelle dimension of approximately 30 nm. The model ink dispersion is prepared using organic dyes (Disperse Yellow 232) and the amphiphilic block copolymer of PCL-b-PAA. The dispersion demonstrates near-Newtonian behavior, which is highly favorable for the application as inkjet ink. Furthermore, the ink dispersion displays a low viscosity, making it particularly suitable for visual communication design and printing purposes. Moreover, the ink dispersion demonstrates an unimodal distribution of the particle size, with an average diameter of approximately 500 nm. It retains exceptional stability of dispersion and even conducts a thermal aging treatment at 60 °C for 5 days. This work presents a facile and efficient synthetic strategy and molecular design of AB di-block copolymer-based dispersants for dye dispersions. [ABSTRACT FROM AUTHOR]