Search

The microstructure and mechanical properties of three kinds of low-carbon medium-manganese steels with different Si contents under an intercritical heat treatment process were studied. The results show that the microstructure of the test forged steel is mainly composed of ferrite and pearlite. After 900 °C complete austenitizing quenching + 720 °C intercritical quenching, the microstructure of the test steel is mainly composed of ferrite and martensite. With the increase in Si content, the microstructure becomes finer and more uniform. The microstructure of the test steel after 900 °C complete austenitizing quenching + 720 °C intercritical quenching + 680 °C intercritical tempering is dominated by ferrite and tempered martensite, with a small amount of retained austenite and cementite. As the Si content increases, the boundaries between ferrite and tempered martensite become more clear. The tensile strength and hardness of the test steel increase with the increase in Si content, while the elongation first increases and then decreases; the comprehensive performance of the test steel is the best when the Si content is 0.685 wt. %, with a tensile strength of 726 MPa, a yield ratio of only 0.65, the highest elongation of 30.5%, and the highest strong plastic product of 22,143 MPa.%. [ABSTRACT FROM AUTHOR]

In this paper, the finite element software ProCAST version 14.5 was used to simulate the temperature field, flow field and defect prediction in the filling and solidification process of hypereutectic high-chromium cast iron. The effects of pouring temperature, negative pressure and the amount of suspension agent added during the technological process were explored. The optimum process parameters were presented. It was found that the suspension agent has a certain hindrance to the filling process, but the filling process remains stable. In the solidification stage, 89.4% of the suspension agent melted, resulting in a relative supercooling degree of 50 °C, which had a certain chilling effect and improved the solidification rate. [ABSTRACT FROM AUTHOR]

In situ NbC-reinforced laser cladding Ni45 coatings have the advantages of high bond strengths, low dilution rates, small heat-affected zones and good wear resistance and have broad application prospects in the field of surface strengthening and repair of workpieces such as automotive molds and engine turbines. Previous studies have mostly used pure niobium powder for in situ synthesis to prepare Ni-based NbC coatings with a high production cost. In this paper, NbC was successfully synthesized in situ in Ni45 powder using inexpensive FeNb65 and Cr3C2. The prepared coating has a uniform microstructure and excellent wear resistance, and the reinforced phases are mainly NbC and Cr23C6. Coating 4# with 25 wt.% FeNb65 + Cr3C2 has the highest microhardness of 776.3HV0.2, about 1.45 times that of the Ni45 coating, and its wear resistance is 36.36 min/mg, about 60.6 times that of the Cr12MoV steel base material and about 23.76 times that of the Ni45 coating. [ABSTRACT FROM AUTHOR]

Nickel-based coatings obtained by laser melting are broadly applied for surface modification owing to their high bond strength and exceptional wear resistance. Nickel-based laser cladding coatings are also extensively employed in high temperature wear environments. In this paper, the research progress on improving the high temperature wear resistance of laser cladding nickel-based composite coatings was reviewed by introducing a hard ceramic phase, adding solid lubricants and rare earth elements. On this basis, the material system to enhance the high temperature wear resistance of coating was summarized from the perspectives of the type, addition amount, morphology and distribution law of the hard ceramic phase, etc. The synergistic effect of various lubricants on improving the high temperature wear resistance of coating was discussed, and the action mechanism of solid lubricants in the high temperature extreme environment was analyzed. Finally, this paper summarizes the main difficulties involved in increasing the high temperature wear resistance of nickel-based coatings and some problems worthy of attention in the future development. [ABSTRACT FROM AUTHOR]

This review examines the methods used to optimize the process parameters of laser cladding, including traditional optimization algorithms such as single-factor, regression analysis, response surface, and Taguchi, as well as intelligent system optimization algorithms such as neural network models, genetic algorithms, support vector machines, the new non-dominance ranking genetic algorithm II, and particle swarm algorithms. The advantages and disadvantages of various laser cladding process optimization methods are analyzed and summarized. Finally, the development trend of optimization methods in the field of laser cladding is summarized and predicted. It is believed that the result would serve as a foundation for future studies on the preparation of high-quality laser cladding coatings. [ABSTRACT FROM AUTHOR]

Hypereutectic High Chromium Cast Iron (HHCCI) is a new type of corrosion-wear-resistant material developed from ordinary high chromium cast iron by increasing the chromium and carbon content and is often used in abrasive environments where wear and corrosion interact. The corrosion wear resistance of the HHCCI is related to the number, size, shape and distribution of carbides and the microstructure of the matrix. This paper reviews the research progress in improving the corrosion wear resistance of HHCCI from various aspects such as primary carbide refinement, heat treatment, deep cooling treatment and alloying, etc. Among the methods of refining primary carbides are modification, semi-solid treatment and current pulse treatment. In addition, we also analyze the potential of Cr, V, Nb, Mo, Mn, W, Ni, Cu, Si, N and other alloying elements to improve the corrosion wear resistance of HHCCI. The mechanism for improving the corrosion wear resistance of HHCCI is also explored in depth and research contents worthy of attention are proposed to further improve the corrosion wear resistance of HHCCI. In the future, the author believes that modification + alloying + heat treatment is the most potential application method to improve the corrosion wear resistance of HHCCI. The corrosion wear resistance of HHCCI can be further improved by refining the primary carbide (such as adding rare earth, Ti and other modified elements) + heat treatment (with cryogenic treatment) to improve the strength + alloying (such as adding low-cost, high-potential alloy elements such as N and Si) to improve the corrosion wear resistance of the matrix. [ABSTRACT FROM AUTHOR]

Isothermal-compression tests of B4Cp/6063Al composites containing 20 vol.% B4C were performed using a Gleeble-3500 device, at strain rates ranging from 0.001 s−1 to 1 s−1 and deformation temperatures ranging from 723 K to 823 K. The results showed that the high-temperature flow stress of B4Cp/6063Al composites increases with the decrease in deformation temperature or the increase in the strain rate. After friction correction, the friction corrected stress was less than the original experimental stress. At the initial stage of deformation, the difference between the rheological stress after friction correction and the measured rheological stress is small, but with the continuous increase in the strain, the difference between the rheological stress after friction correction and the measured rheological stress is grows. Under the same strain, the difference between the rheological stress before and after friction correction becomes more significant with the decrease in the deformation temperature and the increase in the strain rate. Next, the material constants (i.e., α, β, Q, A, n) of B4Cp/6063Al composites were calibrated based on the experimental data, and a constitutive equation was established based on Arrhenius theory. The experimental values and predicted values of the stress–strain curves are in good agreement with the stress–strain curves of the finite element simulation, and the validity of the constitutive equation was verified. [ABSTRACT FROM AUTHOR]

Pure Copper (Cu) is very difficult to prepare using selective laser melting (SLM) technology. This work successfully prepared the pure Cu with high relative density and high strength by the SLM technology using a surface oxidation treatment. The gas-atomized pure Cu powder was used as the feedstock in this work. Before the SLM process, the pure Cu powder was initially handled using the surface oxidation treatment to coat the powder with an extremely thin layer of Cu2O. The SLMed highly dense specimens contain α-Cu and nano-Cu2O phases. A relationship between the processing parameters (laser power (LP), scanning speed (SS), and hatch space (HS)) and density of Cu alloy in SLM was also investigated. The microstructure of SLMed Cu consists of fine grains with grain sizes ranging from 0.5 to ~30 μm. Tensile testing and detailed microstructural characterization were performed on specimens in the as-SLMed and pure copper state specimens. The mechanical property experiments showed that the specimens prepared by SLM technology containing nano-oxide phases had higher yield strength and tensile strength than that of other SLM-built pure copper. However, the elongation was remarkably decreased compared to other SLM-built pure copper, due to the fine grains and the nano-oxides. [ABSTRACT FROM AUTHOR]

The dilution rate has a significant impact on the composition and microstructure of the coatings, and the dilution rate and process parameters have a complex coupling relationship. In this study, three process parameters, namely laser power, powder feeding rate, and scanning speed, were selected as variables to design the orthogonal experiment. The dilution rate and hardness data were obtained from AlCoCrFeNi coatings based on orthogonal experiments. Then, a BP neural network was used to establish a prediction model of the process parameters on the dilution rate. The established BP neural network exhibited good prediction of the dilution rate of AlCoCrFeNi coatings, and the average relative error between the predicted value and the experimental value was only 5.89%. Subsequently, the AlCoCrFeNi coating was fabricated with the optimal process parameters. The results show that the coating was well-formed without defects, such as cracks and pores. The microhardness of the AlCoCrFeNi coating prepared with the optimal process parameters was 521.6 HV0.3. The elements were uniformly distributed in the microstructure, and the grain size was about 20–60 μm. The microstructure of the AlCoCrFeNi coating was only composed of the BCC phase without the existence of the FCC phase and intermetallic compounds. [ABSTRACT FROM AUTHOR]

In this work, the microstructure, alloying element distribution, and borocarbide mechanical properties of high-boron multi-component alloy with Fe-2.0 wt.%B-0.4 wt.%C-6.0 wt.%Cr-x wt.%Mo-1.0%Al-1.0 wt.%Si-1.0 wt.%V-0.5 wt.%Mn (x = 0.0, 2.0, 4.0, 6.0, 8.0) are investigated. The theoretical calculation results and experiments indicate that the microstructure of high-boron multi-component alloy consists of ferrite, pearlite as a matrix and borocarbide as a hard phase. As a creative consideration, through the use of first-principles calculations, the comprehensive properties of borocarbide with different molybdenum concentrations have been predicted. The calculations of energy, state density, electron density and elastic constant of Fe2B crystal cell reveal that substitution of the molybdenum atom in the Fe2B crystal cell can remarkably improve its thermodynamic stability, bond strength, and covalent trend. For verifying the accuracy of this theoretical calculation, nano-indentation testing is carried out, the results of which indicate that the actual properties of borocarbide present favorable consistency with the theoretical calculations. [ABSTRACT FROM AUTHOR]

Wire-arc additive manufacturing (WAAM) has been considered as one of the potential additive-manufacturing technologies to fabricate large components. However, its industrial application is still limited by the existence of stress and distortion. During the process of WAAM, the scanning pattern has an important influence on the temperature field, distortion and final quality of the part. Four kinds of deposition patterns, including sequence, symmetry, in–out and out–in, were designed to deposit H13 steel in this study. An in situ measurement system was set up to record the temperature history and the progress of accumulated distortion of the parts during deposition. An S value was proposed to evaluate the distortion of the substrate. It was shown that the distortion of the part deposited by sequence was significantly larger than those of other parts. The distortion deposited by the out–in pattern decreased by 68.6% compared with sequence. The inherent strain method and strain parameter were introduced to expose the mechanism of distortion reduction caused by pattern variation. [ABSTRACT FROM AUTHOR]

This work investigated the microstructure and mechanical property of high-boron multi-component alloy with Fe, B, C, Cr, Mo, Al, Si, V, Mn and different contents of Ti. The results indicate that the as-cast metallurgical microstructure of high-boron multi-component alloys consist of ferrite, pearlite and borocarbide. In an un-modified alloy, continuous reticular structure of borocarbide is observed. After titanium addition, the structure of borocarbide changes into a fine and isolated morphology. TiC is the existence form of titanium in the alloy, which acts as the heterogeneous nuclei for eutectic borocarbide. Moreover, impact toughness of the alloy is remarkably improved by titanium modification. [ABSTRACT FROM AUTHOR]

Mechanical properties, electronic properties, and Debye temperatures of NixBy (Ni3B, Ni2B, Ni4B3 and NiB) compounds were obtained by the first principles calculations based on the density functional theory (DFT). The results showed that the formation enthalpy of the NixBy compounds were stable with negative formation enthalpy. NiB had the largest B, G, and E, and the smallest υ; it also had the highest hardness (10.8 GPa) and Debye temperature (681.8 K). Ni4B3 had the strongest anisotropy. It was found that the valence bonds of the NixBy compounds studied were composed of both metal bond and covalent bond, and the mechanical properties and Debye temperature of the NixBy compounds increased with the increase of the B atomic ratio. [ABSTRACT FROM AUTHOR]