Search

Increased use and production of engineered nanoparticles (NPs) lead to an elevated risk of their diffuse dispersion into the aquatic environment and increased concern on unknown effects induced by their release into the aquatic ecosystem. An improved understanding of the environmental transformation processes of NPs of various surface characteristics is hence imperative for risk assessment and management. This study presents results on effects of natural organic matter (NOM) on the environmental transformation and dissolution of metal and metal oxide NPs of different surface and solubility properties in synthetic freshwater (FW) with and without NOM. Adsorption of NOM was evident on most of the studied NPs, except Sb and Sb2O3, which resulted in the formation of negatively charged colloids of higher stability and smaller size distribution compared with the same NPs in FW only. The dissolution rate of the NPs in the presence of NOM correlated with the strength of interactions between the carboxylate group of NOM and the particle surface, and resulted in either no (Mn, Sb, ZnO NPs), increased (Co, Sn NPs) and decreased (Ni, NiO, Sb2O3, Y2O3 NPs) levels of dissolution. One type of metal NP from each group (Mn, Ni, Sn) were investigated to assess whether observed differences in adsorption of NOM and dissolution would influence their ecotoxic potency. The results showed Mn, Ni, and Sn NPs to generate intracellular reactive oxygen species (ROS) in a time and dose-dependent manner. The extent of ROS generation in FW was similar for both Mn and Ni NPs but higher for Sn NPs. These findings are possibly related to interactions and infiltration of the NPs with the cells, which lead to redox imbalances which could induce oxidative stress and cell damage. At the same time, the presence of NOM generally reduced the intracellular ROS generation by 20-40% for the investigated NPs and also reduced cytotoxicity of Sn NPs, which can be attributed to the stronger interaction of carboxy, QC 20220315

Since 2021, cobalt (Co) is in Europe classified as carcinogen in quantities exceeding 0.1 wt-%. This affects nickel-rich stainless steels, which contain about 0.2 wt-% Co impurities. Previous findings show the bioaccessibility of Co in stainless steel to be primarily determined by the corrosion resistance. It has been unclear whether Co is distributed heterogeneously in the alloy and the outermost surface and whether a specific location would pose a risk for Co release under specific exposure conditions. This study aimed at locating Co in stainless steel 316L (0.2 wt-% Co) surfaces prior to and after exposure to different synthetic body fluids for 24 h at 37 °C. Time-of-flight secondary ion mass spectrometry (ToF-SIMS), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma mass spectrometry (ICPMS) investigated the location of Co in the surface oxide and extent of release along with other metals (iron, chromium, nickel, and manganese) into synthetic biological fluids (gastric fluid, pH 1.5; lysosomal fluid, pH 4.5; phosphate buffered saline-PBS, pH 7.4). Co was homogeneously distributed along with metallic nickel beneath the surface oxide and co-released with other metals upon surface reformation and passivation. Exposure in PBS resulted in the incorporation of both Co and phosphate in the oxide., Not duplicate with DiVA 1611076QC 20221125

Diffusely dispersed metal and metal oxide nanoparticles (NPs) can adversely affect living organisms through various mechanisms and exposure routes. One mechanism behind their toxic potency is their ability to generate reactive oxygen species (ROS) directly or indirectly to an extent that depends on the dose, metal speciation, and exposure route. This review provides an overview of the mechanisms of ROS formation associated with metal and metal oxide NPs and proposes a possible way forward for their future categorization. Metal and metal oxide NPs can form ROS via processes related to corrosion, photochemistry, and surface defects, as well as via Fenton, Fenton-like, and Haber-Weiss reactions. Regular ligands such as biomolecules can interact with metallic NP surfaces and influence their properties and thus their capabilities of generating ROS by changing characteristics such as surface charge, surface composition, dissolution behavior, and colloidal stability. Interactions between metallic NPs and cells and their organelles can indirectly induce ROS formation via different biological responses. H2O2 can also be generated by a cell due to inflammation, induced by interactions with metallic NPs or released metal species that can initiate Fenton(-like) and Haber-Weiss reactions forming various radicals. This review discusses these different pathways and, in addition, nano-specific aspects such as shifts in the band gaps of metal oxides and how these shifts at biologically relevant energies (similar to activation energies of biological reactions) can be linked to ROS production and indicate which radical species forms. The influences of kinetic aspects, interactions with biomolecules, solution chemistry (e.g., Cl- and pH), and NP characteristics (e.g., size and surface defects) on ROS mechanisms and formation are discussed. Categorization via four tiers is suggested as a way forward to group metal and metal oxide NPs based on the ROS reaction pathways that they may unde, QC 20220627

Cobalt (Co) nanoparticles (NPs) may be diffusely dispersed into natural ecosystems from various anthropogenic sources such as traffic settings and eventually end up in aquatic systems. As environmentally dispersed Co NPs may be transferred through an aquatic food web, this study investigated this transfer from algae (Scendesmus sp.) to zooplankton (Daphnia magna) to fish (Crucian carp, Carassius carassius). Effects of interactions between naturally excreted biomolecules from D. magna and Co NPs were investigated from an environmental fate perspective. ATR-FTIR measurements showed the adsorption of both algae constituents and excreted biomolecules onto the Co NPs. Less than 5% of the Co NPs formed heteroagglomerates with algae, partly an effect of both agglomeration and settling of the Co NPs. The presence of excreted biomolecules in the solution did not affect the extent of heteroagglomeration. Despite the low extent of heteroagglomeration between Co NPs and algae, the Co NPs were transferred to the next trophic level (D. magna). The Co uptake in D. magna was 300 times larger than the control samples (without Co NP), which were not influenced by the addition of excreted biomolecules to the solution. Significant uptake of Co was observed in the intestine of the fish feeding on D. magna containing Co NPs. No bioaccumulation of Co was observed in the fish. Moreover, 10–20% of the transferred Co NP mass was dissolved after 24 h in the simulated gut solution of the zooplankton (pH 7), and 50–60% was dissolved in the simulated gut solution of the fish (pH 4). The results elucidate that Co NPs gain different properties upon trophic transfer in the food web. Risk assessments should hence be conducted on transformed and weathered NPs rather than on pristine particles., QC 20240703

QC 20211203

As the use of engineered nanomaterials increases, so does the risk of them spreading to natural ecosystems. Hitherto, knowledge regarding the toxic properties of nanoparticles (NP's) and their potential interactions with natural bio-organic molecules adsorbed to them, and thereby forming surface coronas, is limited. However, we show here that the toxic effect of NPs of tungsten carbide cobalt (WC-Co) and cobalt (Co) on the crustacean Daphnia magna is postponed in the presence of natural biological degradation products (eco-corona biomolecules). For Daphnia exposed to WC-Co NPs the survival time increased with 20-25% and for Co NPs with 30-47% after mixing the particles with a solution of eco-corona biomolecules before exposure. This suggests that an eco-corona, composed of biomolecules always present in natural ecosystems, reduces the toxic potency of both studied NPs. Further, the eco-coronas did not affect the particle uptake, suggesting that the reduction in toxicity was related to the particle-organism interaction after eco-corona formation. In a broader context, this implies that although the increasing use and production of NPs may constitute a novel, global environmental threat, the acute toxicity and long-term effects of some NPs will, at least under certain conditions, be reduced as they enter natural ecosystems., QC 20210720

The fluorescent probe 2′,7′-dichlorofluorescein diacetate (DCFH-DA) together with the enzyme horseradish peroxidase (HRP) is widely used in nanotoxicology to study acellular reactive oxygen species (ROS) production from nanoparticles (NPs). This study examined whether HRP adsorbs onto NPs of Mn, Ni, and Cu and if this surface process influences the extent of metal release and hence the ROS production measurements using the DCFH assay in phosphate buffered saline (PBS), saline, or Dulbecco’s modified Eagle’s medium (DMEM). Adsorption of HRP was evident onto all NPs and conditions, except for Mn NPs in PBS. The presence of HRP resulted in an increased release of copper from the Cu NPs in PBS and reduced levels of nickel from the Ni NPs in saline. Both metal ions in solution and the adsorption of HRP onto the NPs can change the activity of HRP and thus influence the ROS results. The effect of HRP on the NP reactivity was shown to be solution chemistry dependent. Most notable was the evident affinity/adsorption of phosphate toward the metal NPs, followed by a reduced adsorption of HRP, the concomitant reduction in released manganese from the Mn NPs, and increased levels of released metals from the Cu NPs in PBS. Minor effects were observed for the Ni NPs. The solution pH should be monitored since the release of metals can change the solution pH and the activity of HRP is known to be pH-dependent. It is furthermore essential that solution pH adjustments are made following the addition of NaOH during diacetyl removal of DCFH-DA. Even though not observed for the given exposure conditions of this study, released metal ions could possibly induce agglomeration or partial denaturation of HRP, which in turn could result in steric hindrance for H2O2 to reach the active site of HRP. This study further emphasizes the influence of HRP on the background kinetics, its solution dependence, and effects on measured ROS signals. Different ways of correcting for the background are highlig, QC 20210802

Pure metallic Co, Ni, and their bimetallic compositions of Co3Ni, CoNi, and CoNi3 nanomaterials were prepared by solution combustion synthesis. Microstructure, phase composition, and crystalline structure of these nanoparticles (NPs) were characterized along with studies of their corrosion and dissolution properties in synthetic freshwater with and without natural organic matter (NOM). The nanomaterials consisted of aggregates of fine NPs (3-30 nm) of almost pure metallic and bimetallic crystal phases with a thin surface oxide covered by a thin carbon shell. The nanomaterials were characterized by BET surface areas ranging from similar to 1 to 8 m(2)/g for the Ni and Co NPs, to 22.93 m(2)/g, 14.86 m(2)/g, and 10.53 m(2)/g for the Co3Ni, CoNi, CoNi3 NPs, respectively. More Co and Ni were released from the bimetallic NPs compared with the pure metals although their corrosion current densities were lower. In contrast to findings for the pure metal NPs, the presence of NOM increased the release of Co and Ni from the bimetallic NPs in freshwater compared to freshwater only even though its presence reduced the corrosion rate (current density). It was shown that the properties of the bimetallic nanomaterials were influenced by multiple factors such as their composition, including carbon shell, type of surface oxides, and the entropy of mixing., QC 20220215

Gold (Au) nanoparticles (NPs) are widely used in nanomedical applications as a carrier for molecules designed for different functionalities. Previous findings suggested that biological molecules, including amino acids, could contribute to the dissolution of Au NPs in physiological environments and that this phenomenon was size-dependent. We, therefore, investigated the interactions of L-cysteine with 5-nm Au NPs by means of time-of-flight secondary ion mass spectrometry (ToF-SIMS). This was achieved by loading Au NPs on a clean aluminum (Al) foil and immersing it in an aqueous solution containing L-cysteine. Upon rinsing off the excessive cysteine molecules, ToF-SIMS confirmed the formation of gold cysteine thiolate via the detection of not only the Au-S bond but also the hydrogenated gold cysteine thiolate molecular ion. The presence of NaCl or a 2-(N-morpholino)ethanesulfonic acid buffer disabled the detection of Au NPs on the Al foil. The detection of larger (50-nm) Au NPs was possible but resulted in weaker cysteine and gold signals, and no detected gold cysteine thiolate signals. Nano-gold specific adsorption of L-cysteine was also demonstrated by cyclic voltammetry using paraffine-impregnated graphite electrodes with deposited Au NPs. We demonstrate that the superior chemical selectivity and surface sensitivity of ToF-SIMS, via detection of elemental and molecular species, provide a unique ability to identify the adsorption of cysteine and formation of gold-cysteine bonds on Au NPs., QC 20210430

The increased use of nanoparticles (NPs) requires efficient testing of their potential toxic effects. A promising approach is to use reporter cell lines to quickly assess the activation of cellular stress response pathways. This study aimed to use the ToxTracker reporter cell lines to investigate (geno)toxicity of various metal-or metal oxide NPs and draw general conclusions on NP-induced effects, in combination with our previous findings. The NPs tested in this study (n = 18) also included quantum dots (QDs) in different sizes. The results showed a large variation in cytotoxicity of the NPs tested. Furthermore, whereas many induced oxidative stress only few activated reporters related to DNA damage. NPs of manganese (Mn and Mn3O4) induced the most remarkable ToxTracker response with activation of reporters for oxidative stress, DNA damage, protein unfolding and p53-related stress. The QDs (CdTe) were highly toxic showing clearly size-dependent effects and calculations suggest surface area as the most relevant dose metric. Of all NPs investigated in this and previous studies the following induce the DNA damage reporter; CuO, Co, CoO, CdTe QDs, Mn, Mn3O4, V2O5, and welding NPs. We suggest that these NPs are of particular concern when considering genotoxicity induced by metal-and metal oxide NPs., QC 20200420

Relevant in vitro assays that can simulate exposure to nanoparticles (NPs) via inhalation are urgently needed. Presently, the most common method employed is to expose lung cells under submerged conditions, but the cellular responses to NPs under such conditions might differ from those observed at the more physiological air-liquid interface (ALI). The aim of this study was to investigate the cytotoxic and inflammatory potential of CeO2 NPs (NM-212) in a co-culture of A549 lung epithelial cells and differentiated THP-1 cells in both ALI and submerged conditions. Cellular dose was examined quantitatively using inductively coupled plasma mass spectrometry (ICP-MS). The role of serum and LPS-priming for IL-1 beta release was further tested in THP-1 cells in submerged exposure. An aerosol of CeO2 NPs was generated by using the PreciseInhale (R) system, and NPs were deposited on the co-culture using XposeALI (R). No or minor cytotoxicity and no increased release of inflammatory cytokines (IL-1 beta, IL-6, TNF alpha, MCP-1) were observed after exposure of the co-culture in ALI (max 5 mu g/cm(2)) or submerged (max 22 mu g/cm(2)) conditions. In contrast, CeO2 NPs cause clear IL-1 beta release in monocultures of macrophage-like THP-1, independent of the presence of serum and LPS-priming. This study demonstrates a useful approach for comparing effects at various in-vitro conditions., QC 20200629

The neurotoxicity of hard metal-based nanoparticles (NPs) remains poorly understood. Here, we deployed the human neuroblastoma cell line SH-SY5Y differentiated or not into dopaminergic- and cholinergic-like neurons to study the impact of tungsten carbide (WC) NPs, WC NPs sintered with cobalt (Co), or Co NPs versus soluble CoCl2. Co NPs and Co salt triggered a dose-dependent cytotoxicity with an increase in cytosolic calcium, lipid peroxidation, and depletion of glutathione (GSH). Co NPs and Co salt also suppressed glutathione peroxidase 4 (GPX4) mRNA and protein expression. Co-exposed cells were rescued by N-acetylcysteine (NAC), a precursor of GSH, and partially by liproxstatin-1, an inhibitor of lipid peroxidation. Furthermore, in silico analyses predicted a significant correlation, based on similarities in gene expression profiles, between Co-containing NPs and Parkinson's disease, and changes in the expression of selected genes were validated by RT-PCR. Finally, experiments using primary human dopaminergic neurons demonstrated cytotoxicity and GSH depletion in response to Co NPs and CoCl2 with loss of axonal integrity. Overall, these data point to a marked neurotoxic potential of Co-based but not WC NPs and show that neuronal cell death may occur through a ferroptosis-like mechanism., QC 20200630

The use of silver nanoparticles (Ag NPs) in consumer products can result in diffuse environmental dispersion of both NPs and ionic silver. This study investigated the transformation of Ag NPs present in two consumer products (skin cream, mouth spray) in terms of release of Ag NPs and ionic silver and changes in particle size in artificial sweat and saliva solutions. Large differences in silver release were observed with the smaller sized Ag NPs in mouth spray releasing more silver compared with the Ag NPs of the skin cream. Substantial particle agglomeration took place in both artificial sweat and saliva, forming large-sized agglomerates (> 100 nm). The amount of dissolved silver in solution after 24 h was less than 10% of the total amount of Ag NPs for both products. The results show that the Ag NPs of these consumer products will largely remain as NPs even after 24 h of skin or saliva contact. The use of normalization by geometric surface area of the particles was tested as a way to compare dissolution for Ag NPs of different characteristics, including pristine, bare, as well as PVP-capped Ag NPs. Normalization of silver dissolution with the geometric surface area was shown promising, but more extensive studies are required to unambiguously conclude whether it is a way forward to enable grouping of the dissolution behavior of Ag NPs released from consumer products., QC 20210308

Cobalt (Co) nanoparticles (NPs) are produced in different applications and unintentionally generated at several occupational and traffic settings. Their diffuse dispersion may lead to interactions with humans and aquatic organisms via different exposure routes that include their transformation/dissolution in biological media. This paper has investigated the particle stability and reactivity of Co NPs (dispersed by sonication prior to exposure) interacting with selected individual biomolecules (amino acids, polypeptides, and proteins) in phosphate-buffered saline (PBS). No or minor adsorption of amino acids (glutamine, glutamic acid, lysine, and cysteine) was observed on the Co NPs, independent of the functional group and charge. Instead, phosphate adsorption resulted in the formation of a surface layer (a corona) of Co phosphate. The adsorption of larger biomolecules (polyglutamic acid, polylysine, lysozyme, and mucin) was evident in parallel with the formation of Co phosphate. The dissolution of the Co NPs was rapid as 35-55% of the particle mass was dissolved within the first hour of exposure. The larger biomolecules suppressed the dissolution initially compared to exposure in PBS only, whereas the dissolution was essentially unaffected by the presence of amino acids, with cysteine as an exception. The formation of Co phosphate on the NP surface reduced the protective properties of the surface oxide of the Co NPs, as seen from the increased levels of the released Co when compared with the nonphosphate-containing saline. The results underline the diversity of possible outcomes with respect to surface characteristics and dissolution of Co NPs in biological media and emphasize the importance of surface interactions with phosphate on the NP characteristics and reactivity., QC 20200117

Knowledge on relations between particle properties and dissolution/transformation characteristics of metal and metal oxide nanoparticles (NPs) in freshwater is important for risk assessment and product development. This critical review aims to elucidate nanospecific effects on dissolution of metallic NPs in freshwater and similar media. Dissolution rate constants are compiled and analyzed for NPs of silver (Ag), copper (Cu), copper oxide/hydroxide (CuO, Cu(OH) 2 ), zinc oxide (ZnO), manganese (Mn), and aluminum (Al), showing largely varying (orders of magnitude) constants when modeled using first order kinetics. An effect of small primary sizes (<15 nm) was observed, leading to increased dissolution rate constants and solubility in some cases. However, the often extensive particle agglomeration can result in reduced nanospecific effects on dissolution and also an increased uncertainty related to the surface area, a parameter that largely influence the extent of dissolution. Promising ways to model surface areas of NPs in solution using fractal dimensions and size distributions are discussed in addition to nanospecific aspects related to other processes such as corrosion, adsorption of natural organic matter (NOM), presence of capping agents, and existence of surface defects. The importance of the experimental design on the results of dissolution experiments of metal and metal oxide NPs is moreover highlighted, including the influence of ionic metal solubility and choice of particle dispersion methodology., QC 20190821

QC 20191010

Investigations of metal ecotoxicity in life cycle assessment (LCA) and life cycle impact assessment (LCIA) are becoming important tools for evaluating the environmental impact of a product or process. There is, however, improvement needed for LCIA of metal ecotoxicity in order to make this assessment more relevant and robust. In this work, three issues within the LCIA of metal ecotoxicity are investigated, mainly focusing on topics related to stainless steel manufacturing. The first issue is the importance of considering regional water chemistry when constructing the characterization factor (CF). A model freshwater of relevance for stainless steel manufacturing in a region of Sweden was created with chemistry different from available options. The second issue is related to the lack of consideration on changes in speciation of Cr(VI) in freshwater for a given emission, as Cr(VI) to some extent will be reduced to Cr(III). Two new options are suggested based on relationships between the Cr(VI)-total Cr ratio as a way to improve the relevancy of LCIA for Cr(VI) in freshwater. The last issue is how to treat metal release from slags in LCIA. Metal release from slags was shown to vary significantly between different ways of modelling slag emissions (differences in total metal content, slag leaching tests, estimated emissions to groundwater)., QC20190612

This work focuses on kinetic aspects of stability, mobility, and dissolution of bare Cu, Al and Mn, and SiO2 NPs in synthetic freshwater (FW) with and without the presence of natural organic matter (NOM). This includes elucidation of particle and surface interactions, metal dissolution kinetics, and speciation predictions of released metals in solution. Dihydroxy benzoic acid (DHBA) and humic acid adsorbed rapidly on all metal NPs (< 1 min) via multiple surface coordinations, followed in general by rapid agglomeration and concomitant sedimentation for a large fraction of the particles. In contrast, NOM did not induce agglomeration of the SiO2 NPs during the test duration (21 days). DHBA in concentrations of 0.1 and 1 mM was unable to stabilize the metal NPs for time periods longer than 6 h, whereas humic acid, at certain concentrations (20 mg/L) was more efficient (> 24 h). The presence of NOM increased the amount of released metals into solution, in particular for Al and Cu, whereas the effect for Mn was minor. At least 10% of the particle mass was dissolved within 24 h and remained in solution for the metal NPs in the presence of NOM. Speciation modeling revealed that released Al and Cu predominantly formed complexes with NOM, whereas less complexation was seen for Mn. The results imply that potentially dispersed NPs of Cu, Al and Mn readily dissolve or sediment close to the source in freshwater of low salinity, whereas SiO2 NPs are more stable and therefore more mobile in solution., QC 20180323

An increasing use of cobalt (Co)-based nanoparticles (NPs) in different applications and exposures at occupational settings triggers the need for toxicity assessment. Improved understanding regarding the physiochemical characteristics of Co metal NPs and different oxides in combination with assessment of toxicity and mechanisms may facilitate decisions for grouping during risk assessment. The aim of this study was to gain mechanistic insights in the correlation between NP reactivity and toxicity of three different Co-based NPs (Co, CoO, and Co3O4) by using various tools for characterization, traditional toxicity assays, as well as six reporter cell lines (ToxTracker) for rapid detection of signaling pathways of relevance for carcinogenicity. The results showed cellular uptake of all NPs in lung cells and induction of DNA strand breaks and oxidative damage (comet assay) by Co and CoO NPs. In-depth studies on the ROS generation showed high reactivity of Co, lower for CoO, and no reactivity of Co3O4 NPs. The reactivity depended on the corrosion and transformation/dissolution properties of the particles and the media highlighting the role of the surface oxide and metal speciation as also confirmed by in silico modeling. By using ToxTracker, Co NPs were shown to be highly cytotoxic and induced reporters related to oxidative stress (Nrf2 signaling) and DNA strand breaks. Similar effects were observed for CoO NPs but at higher concentrations, whereas the Co3O4 NPs were inactive at all concentrations tested. In conclusion, our study suggests that Co and CoO NPs, but not Co3O4, may be grouped together for risk assessment., QC 20181214

QC 20180917

As the production and usage of nanomaterials are increasing so are the concerns related to the release of the material into nature. Tungsten carbide (WC) is widely used for its hard metal properties, although its use, in for instance tyre studs, may result in nano-sized particles ending up in nature. Here, we evaluate the potential long-term exposure effects of WC nanoparticles on a pelagic (Daphnia magna) and a benthic (Asellus aquaticus) organism. No long-term effects were observed in the benthic system with respect to population dynamics or ecosystem services. However, long-term exposure of D. magna resulted in increased time to first reproduction and, if the particles were resuspended, strong effects on survival and reproductive output. Hence, the considerable differences in acute vs. long-term exposure studies revealed here emphasize the need for more long-term studies if we are to understand the effects of nanoparticles in natural systems., QC 20180209

Studded tyres made of tungsten carbide cobalt (WC-Co) are in the Northern countries commonly used during the winter time. Tungsten (W)-containing nano- and micron-sized particles have been detected close to busy roads in several European countries. Other typical traffic wear particles consist of copper (Cu). The aims of this study were to investigate particle stability and transformation/dissolution properties of nanoparticles (NPs) of WC-Co compared with NPs of tungsten carbide (WC), cobalt (Co), and Cu. Their physicochemical characteristics (primarily surface oxide and charge) are compared with their extent of sedimentation and metal release in synthetic surface water (SW) with and without two different model organic molecules, 2,3- and 3,4-dihydroxybenzoic acid (DHBA) mimicking certain sorption sites of humic substances, for time periods up to 22 days. The WC-Co NPs possessed a higher electrochemical and chemical reactivity in SW with and without DHBA molecules as compared with NPs of WC, Co, and Cu. Co was completely released from the WC-Co NPs within a few hours of exposure, although it remained adsorbed/bonded to the particle surface and enabled the adsorption of negatively charged DHBA molecules, in contrast with the WC NPs (no adsorption of DHBA). The DHBA molecules were found to rapidly adsorb on the Co and Cu NPs. The sedimentation of the WC and WC-Co NPs was not influenced by the presence of the 2,3- or 3,4-DHBA molecules. A slight influence (slower sedimentation) was observed for the Co NPs, and a strong influence (slower sedimentation) was observed for the Cu NPs in SW with 2,3-DHBA compared with SW alone. The extent of metal release increased in the order: WC < Cu < Co < WC-Co NPs. All NPs released more than 1 wt-% of their metal total mass. The release from the Cu NPs was most influenced by the presence of DHBA molecules., QC 20170607

Corrosion and metal release mechanisms of the biomedical stainless steel grade Type 316L are at human-relevant biological conditions not fully understood. This study focuses on its corrosion properties and release of iron (Fe), chromium (Cr), manganese (Mn), and nickel (Ni) into simulated physiological solutions at pH 7.4 in the presence of proteins. Parallel studies were performed on stainless steel Type 303 containing a substantial amount of MnS inclusions. Metal release studies were performed in phosphate buffered saline (PBS) for 4 h and 24 h at 37 degrees C with or without different concentrations of bovine serum albumin (BSA), fibrinogen from bovine plasma (Fbn), or mixtures of the same. Studies were in addition performed after 1, 4, 6, and 24 h in solutions that were partially replenished after 5 h in order to investigate whether any Vroman effect (exchange of adsorbed proteins by proteins of higher binding affinity) could influence the extent of released metals in solution. This was performed at physiological concentrations of BSA (40 g/L) and Fbn (2.67 g/L) in PBS, and for reference solutions of PBS, PBS with 40 g/L BSA, and PBS with 2.67 g/L Fbn. Changes in open-circuit potential and linear polarization resistance were investigated for the same conditions. After exposure, the exposed surfaces were rinsed and investigated ex situ by means of x-ray photoelectron spectroscopy and infrared reflection absorption spectroscopy. Metal-protein complexation-induced metal release mechanisms were found to be most pronounced for Type 316L and the release of Fe, Cr, and Ni. Fibrinogen adsorbed differently onto Type 303 (thicker conformation of adsorbed proteins) as compared with Type 316L and occasionally induced corrosion events for Type 303. Mn was mostly released from inclusions present in the Type 303 alloy, most probably via non-electrochemical mechanisms. A Vroman effect was observed for both grades. A significant extent of precipitation of metal-rich protein aggr, QC 20171121

The zeta potential (ZP) is a parameter commonly used to characterize metal nanoparticles (NPs) in solution. Such determinations are for example performed in nanotoxicology since the ZP influences e.g. the interaction between cells and different biomolecules. Four case studies on different metal NPs (Cu and Zn NPs, and citrate capped Ag NPs) are presented in this study in order to provide guidance on how to accurately interpret and report ZP data. Solutions of high ionic strength (150 mM NaCl) induce a higher extent of particle agglomeration (elucidated with Ag NPs) when compared with conditions in 10 mM NaCl, which further complicates the prediction of the ZP due to e.g. sedimentation and broadening of the zeta potential distribution. The particle size is seldom included specifically in the standard ways of determining ZP (Huckel and Smoluchowski approximations). However corrections are possible when considering approximations of the Henry function. This was seen to improve the analysis of NPs, since there are cases when both the Huckel and the Smulochowski approximations are invalid. In biomolecule-containing cell media (BEGM), the signal from e.g. proteins may interfere with the measured ZP of the NPs. The intensity distribution of the ZP of both the blank solution and the solution containing NPs should hence be presented in addition to the mean value. Due to an increased ionic strength for dissolving of metal NPs (exemplified by Zn NPs), the released metal ions must be considered when interpreting the zeta potential measurements. In this work the effect was however negligible, as the particle size was several hundred nm, conditions that made the Smoluchowski approximation valid despite an increased ionic strength. However, at low ionic strengths (mM range) and small-sized NPs (tens of nm), the effect of released metal ions can influence the choice of model for determining the zeta potential. Sonication of particle dispersions influences not only the extent of met, QC 20170824

Even though anthropogenic nano-sized tungsten carbide nanoparticles (WC NPs) have been found in the environment, there are currently no investigations on their environmental fate. This work studies the interaction between natural organic matter (NOM) and WC NPs, as well as the potential uptake by the aquatic model organism Daphnia magna. We here show that the affinity between WC NPs and humic acid or dihydroxybenzoic acid (DHBA), which are model molecules of NOM, is very low with no observed surface adsorption. The lack of a stabilizing effect of these organic molecules, in combination with a relatively high effective density of WC NP agglomerates in humic acid, resulted in the substantial agglomeration and sedimentation of the WC NPs. A higher stability of the smaller sized WC NP agglomerates (<150 nm) means that this fraction is mobile and can be transported to other settings, suggesting that this particle fraction should be considered in further studies. The dissolution of tungsten from WC NPs was continuous and the relatively slow dissolution rate (on the order of 0.03 mg m-2 h-1) implies that particle transport will not be severely limited from a dissolution perspective. Uptake of tungsten (dissolved tungsten and WC particles) by D. magna was observed although this did not induce any acute toxic effects., Funding details: ICP, Instituto Científico Pfizer; Funding details: KTH, Kungliga Tekniska Högskolan; Funding text: This work is a part of the Mistra Environmental Nanosafety program, and the financial support from Mistra is greatly acknowledged. Sara Isaksson, from KTH, is acknowledged for metal release and size distribution measurements. Alexandre Barreiro Fidalgo, from KTH, is acknowledged for help with ICP measurements. Nanxuan Mei, from KTH, is acknowledged for help with ATR-IR. Dr. Justin Teeguarden, from the Pacific Northwest Laboratory, USA, is acknowledged for providing the Matlab routine for the ISDD computations.QC 20170609

The use of refined toxicological methods is currently needed for characterizing the risks of airborne nanoparticles (NPs) to human health. To mimic pulmonary exposure, we have developed an air-liquid interface (ALI) exposure system for direct deposition of airborne NPs on to lung cell cultures. Compared to traditional submerged systems, this allows more realistic exposure conditions for characterizing toxicological effects induced by airborne NPs. The purpose of this study was to investigate how the deposition of silver NPs (AgNPs) is affected by different conditions of the ALI system. Additionally, the viability and metabolic activity of A549 cells was studied following AgNP exposure. Particle deposition increased markedly with increasing aerosol flow rate and electrostatic field strength. The highest amount of deposited particles (2.2 μg cm-2) at cell-free conditions following 2 h exposure was observed for the highest flow rate (390 ml min-1) and the strongest electrostatic field (±2 kV). This was estimated corresponding to deposition efficiency of 94%. Cell viability was not affected after 2 h exposure to clean air in the ALI system. Cells exposed to AgNPs (0.45 and 0.74 μg cm-2) showed significantly (P < 0.05) reduced metabolic activities (64 and 46%, respectively). Our study shows that the ALI exposure system can be used for generating conditions that were more realistic for in vitro exposures, which enables improved mechanistic and toxicological studies of NPs in contact with human lung cells., QC 20160530

In this study, we elucidate the effect of different sonication techniques to efficiently prepare particle dispersions from selected non-functionalized NPs (Cu, Al, Mn, ZnO), and corresponding consequences on the particle dose, surface charge and release of metals. Probe sonication was shown to be the preferred method for dispersing non-inert, non-functionalized metal NPs (Cu, Mn, Al). However, rapid sedimentation during sonication resulted in differences between the real and the administered doses in the order of 30-80 % when sonicating in 1 and 2.56 g/L NP stock solutions. After sonication, extensive agglomeration of the metal NPs resulted in rapid sedimentation of all particles. DLVO calculations supported these findings, showing the strong van der Waals forces of the metal NPs to result in significant NP agglomeration. Metal release from the metal NPs was slightly increased by increased sonication. The addition of a stabilizing agent (bovine serum albumin) had an accelerating effect on the release of metals in sonicated solutions. For Cu and Mn NPs, the extent of particle dissolution increased from <1.6 to similar to 5 % after sonication for 15 min. A prolonged sonication time (3-15 min) had negligible effects on the zeta potential of the studied NPs. In all, it is shown that it is of utmost importance to carefully investigate how sonication influences the physicochemical properties of dispersed metal NPs. This should be considered in nanotoxicology investigations of metal NPs., QC 20161031

Copper nanoparticles (Cu NPs) are increasingly used in various biologically relevant applications and products, e.g., due to their antimicrobial and catalytic properties. This inevitably demands for an improved understanding on their interactions and potential toxic effects on humans. The aim of this study was to investigate the corrosion of copper nanoparticles in various biological media and to elucidate the speciation of released copper in solution. Furthermore, reactive oxygen species (ROS) generation and lung cell (A549 type II) membrane damage induced by Cu NPs in the various media were studied. The used biological media of different complexity are of relevance for nanotoxicological studies: Dulbecco's modified eagle medium (DMEM), DMEM+ (includes fetal bovine serum), phosphate buffered saline (PBS), and PBS + histidine. The results show that both copper release and corrosion are enhanced in DMEM+, DMEM, and PBS + histidine compared with PBS alone. Speciation results show that essentially no free copper ions are present in the released fraction of Cu NPs in neither DMEM+, DMEM nor histidine, while labile Cu complexes form in PBS. The Cu NPs were substantially more membrane reactive in PBS compared to the other media and the NPs caused larger effects compared to the same mass of Cu ions. Similarly, the Cu NPs caused much more ROS generation compared to the released fraction only. Taken together, the results suggest that membrane damage and ROS formation are stronger induced by Cu NPs and by free or labile Cu ions/complexes compared with Cu bound to biomolecules., QC 20160513

Most metal nanoparticles (NPs), except noble metal NPs, rapidly form a thin surface oxide in ambient conditions. The protective properties of these oxides improve or worsen depending on the environment, e.g., the human lung. Several properties, including the chemical/electrochemical stability and defect density, determine the capacity of these surface oxides to hinder the bulk metal from further oxidation (corrosion). The aim of this study was to investigate whether electrochemical surface oxide characterization of non-functionalized base metal NPs of different characteristics (Al, Mn and Cu) can assist in understanding their bioaccessibility (metal release) in cell media (DMEM+) and their cytotoxic properties following exposure in lung epithelial (A549) cells. The composition and valence states of surface oxides of metal NPs and their electrochemical activity were investigated using an electrochemical technique based on a graphite paste electrode to perform cyclic voltammetry in buffer solutions and open circuit potential measurements in DMEM+. The electrochemical surface oxide characterization was complemented and verified by Raman spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The open circuit potential trends in DMEM+ correlated well with metal release results in the same solution, and provided information on the kinetics of oxide dissolution in the case of Cu NPs. Extensive particle agglomeration in cell medium (DMEM+) was observed by means of photon-cross correlation spectroscopy for all metal NPs, with sedimentation taking place very quickly. As a consequence, measurements of the real dose of added non-functionalized metal NPs to cell cultures for cytotoxicity testing from a sonicated stock solution were shown necessary. The cytotoxic response was found to be strongly correlated to changes in physico-chemical and electrochemical properties of the surface oxides of the metal NPs, the most potent being Cu NPs, followed by Mn NPs. No cyto, QC 20160930

Occupational exposure to airborne nickel is associated with an elevated risk for respiratory tract diseases including lung cancer. Therefore, the increased production of Ni-containing nanoparticles necessitates a thorough assessment of their physical, chemical, as well as toxicological properties. The aim of this study was to investigate and compare the characteristics of nickel metal (Ni) and nickel oxide (NiO) particles with a focus on Ni release, reactive oxygen species (ROS) generation, cellular uptake, cytotoxicity and genotoxicity. Four Ni-containing particles of both nano-size (Ni-n and NiO-n) and micron-size (Ni-m1 and Ni-m2) were tested. The released amount of Ni in solution was notably higher in artificial lysosomal fluid (e.g. 80-100 wt% for metallic Ni) than in cell medium after 24h (ca. 1-3 wt% for all particles). Each of the particles was taken up by the cells within 4 h and they remained in the cells to a high extent after 24 h post-incubation. Thus, the high dissolution in ALF appeared not to reflect the particle dissolution in the cells. Ni-m1 showed the most pronounced effect on cell viability after 48 h (alamar blue assay) whereas all particles showed increased cytotoxicity in the highest doses (20-40 mu g cm(2)) when assessed by colony forming efficiency (CFE). Interestingly an increased CFE, suggesting higher proliferation, was observed for all particles in low doses (0.1 or 1 mu g cm(-2)). Ni-m1 and NiO-n were the most potent in causing acellular ROS and DNA damage. However, no intracellular ROS was detected for any of the particles. Taken together, micron-sized Ni (Ni-m1) was more reactive and toxic compared to the nano-sized Ni. Furthermore, this study underlines that the low dose effect in terms of increased proliferation observed for all particles should be further investigated in future studies., QC 20161007

The increasing use of silver nanoparticles (AgNPs) in consumer products triggers the need for investigations that improve the understanding of their chemical transformations upon environmental entry. Such knowledge provides crucial information for toxicological studies and risk assessments. Interactions with the soil compartment need to be explored as there are evident risks of the dispersion of both AgNPs and of released Ag ions/complexes present in wastewater-treated sludge that is distributed onto agricultural land. The dissolution and fractionation in solution of bare (AgNP-bare, noncoated) and coated AgNPs (AgNP-coat, stabilized with two nonionic surfactants, polyoxyethylene glycerol trioleate and Tween 20) were investigated after 4 and 48h in suspensions of one sandy and one clayey soil of different pHs (3.3, 5.2). Parallel experiments were performed with soil suspensions spiked with easily soluble AgNO3. Silver in the water phase was separated in a dissolved fraction (mainly Ag ions/complexes) and a particle fraction (mainly AgNP/agglomerates/Ag adsorbed on organic matter) by means of ultracentrifugation. Bare AgNPs were nonstable and dissolved to a significantly larger extent in the sandy soil mixture compared to coated AgNPs. The concentration of dissolved Ag (ions/complexes) in the water phase was similar in the case of bare AgNPs and AgNO3 (at pH 3 and 5.2) after 24h in sandy soil, which implies a high degree of dissolution of bare AgNPs (50-100%). In contrast, approximately 50% of the coated AgNPs remained in the water phase after 48h of equilibration in the sandy soil at pH 5.2. The clayey soil had a significantly higher sorption capacity of Ag compared with the sandy soil, as Ag in the case of coated AgNPs was only detected in the water phase of pH 5.2 (<1 % of added Ag). Ultracentrifugation was proven more efficient compared with microfiltration to separate the dissolved Ag fraction (ions/complexes) and the particle fraction (AgNPs/agglomerates) of, QC 20150707

Adsorption of a single layer of molecules on a surface, or even a reorientation of already present molecules, can significantly affect the surface properties of a material. In this study, vibrational sum frequency spectroscopy (VSFS) has been used to study the change in molecular structure at the solid-air interface following thermal curing of polyelectrolyte multilayers of poly(allylamine hydrochloride) and poly(acrylic acid). Significant changes in the VSF spectra were observed after curing. These changes were accompanied by a distinct increase in the static water contact angle, showing how the properties of the layer-by-layer molecular structure are controlled not just by the polyelectrolyte in the outermost layer but ultimately by the orientation of the chemical constituents in the outermost layers., QC 20150528

This review on copper runoff dispersed from unsheltered naturally patinated copper used for roofing and facades summarizes and discusses influencing factors, available literature, and predictive models, and the importance of fate and speciation for environmental risk assessment. Copper runoff from. outdoor surfaces is predominantly governed by electrochemical and chemical reactions and is highly dependent on given exposure conditions (size, inclination, geometry, degree of sheltering, and orientation), surface parameters (age, patina composition, and thickness), and site-specific environmental conditions (gaseous pollutants, chloride, rainfall characteristics (amount, intensity, pH), wind direction, temperature, time of wetness, season). The corrosion rate cannot be used to assess the runoff rate. The extent of released copper varies largely between different rain events and is related to dry and wet periods, dry deposition prior to the rain event and prevailing rain and patina characteristics. Interpretation and use of copper runoff data for environmental risk assessment and management need therefore to consider site-specific factors and focus on average data of long-term studies (several years). Risk assessments require furthermore that changes in copper speciation, bioavailability aspects, and potential irreversible retention on solid surfaces are considered, factors that determine the environmental fate of copper runoff from outdoor surfaces., QC 20140324

Stainless steel is widely used in biological environments, for example as implant material or in food applications, where adsorption-controlled ligand-induced metal release is of importance from a corrosion, health, and food safety perspective. The objective of this study was to elucidate potential correlations between surface energy and wettability of stainless steel surfaces and the release of iron in complexing biological media. This was accomplished by studying changes in surface energies calculated from contact angle measurements, surface oxide composition (X-ray photoelectron spectroscopy), and released iron (graphite furnace atomic absorption spectroscopy) for stainless steel grade AISI 304 immersed in fluids containing bovine serum albumin or citric acid, and non-complexing fluids such as NaCl, NaOH, and HNO3. It was shown that the surface wettability and polar surface energy components were all influenced by adventitious atmospheric carbon (surface contamination of low molecular weight), rather than differences in surface oxide composition in non-complexing solutions. Adsorption of both BSA and citrate, which resulted in ligand-induced metal release, strongly influenced the wettability and the surface energy, and correlated well with the measured released amount of iron., QC 20150108

A case study of transport and changes in properties of polymer-stabilised Ag NPs is presented in this paper investigating their interaction in different treatment steps within a fully realistic pilot wastewater treatment plant (WWTP), in anaerobic digested sludge, and in soil/sludge mixtures. The fate of the same Ag NPs was tracked in these environments, hence taking the history of the Ag NPs into account. The results show that most of the Ag NPs end up in the sludge (80-100%), also after anaerobically digestion. Furthermore, the fraction of silver in the supernatant was very low after 48h incubation with silver-containing digested sludge mixed with different soil types. However, when Ag NPs were added directly to the sludge/soil mixture, soluble silver was present in the supernatant with sandy soil, but not with clayey soil. In all, generated findings show that risk assessments and toxicological studies of Ag NPs suspensions must take into account possible chemical and particle transformations upon environmental entry, as silver in general become less soluble when transported to WWTPs and interacting with sludge, and soil., QC 20140911

From an increased use of silver nanoparticles (Ag NPs) as an antibacterial in consumer products follows a need to assess the environmental interaction and fate of their possible dispersion and release of silver. This study aims to elucidate an exposure scenario of the Ag NPs potentially released from, for example, impregnated clothing by assessing the release of silver and changes in particle properties in sequential contact with synthetic sweat, laundry detergent solutions, and freshwater, simulating a possible transport path through different aquatic media. The release of ionic silver is addressed from a water chemical perspective, compared with important particle and surface characteristics. Released amounts of silver in the sequential exposures were significantly lower, approximately a factor of 2, than the sum of each separate exposure. Particle characteristics such as speciation (both of Ag ionic species and at the Ag NP surface) influenced the release of soluble silver species present on the surface, thereby increasing the total silver release in the separate exposures compared with sequential immersions. The particle stability had no drastic impact on the silver release as most of the Ag NPs were unstable in solution. The silver release was also influenced by a lower pH (increased release of silver), and cotransported zeolites (reduced silver in solution)., QC 20140811

An increased understanding of nanoparticle toxicity and its impact on human health is essential to enable a safe use of nanoparticles in our society. The aim of this study is to investigate the role of a Trojan horse type mechanism for the toxicity of Ag-nano and CuO-nano particles and their corresponding metal ionic species (using CuCl2 and AgNO3), i.e., the importance of the solid particle to mediate cellular uptake and subsequent release of toxic species inside the cell. The human lung cell lines A549 and BEAS-2B are used and cell death/membrane integrity and DNA damage are investigated by means of trypan blue staining and the comet assay, respectively. Chemical analysis of the cellular dose of copper and silver is performed using atomic absorption spectroscopy. Furthermore, transmission electron microscopy, laser scanning confocal microscopy, and confocal Raman microscopy are employed to study cellular uptake and particle-cell interactions. The results confirm a high uptake of CuO-nano and Ag-nano compared to no, or low, uptake of the soluble salts. CuO-nano induces both cell death and DNA damage whereas CuCl2 induces no toxicity. The opposite is observed for silver, where Ag-nano does not cause any toxicity, whereas AgNO3 induces a high level of cell death. In conclusion: CuO-nano toxicity is predominantly mediated by intracellular uptake and subsequent release of copper ions, whereas no toxicity is observed for Ag-nano due to low release of silver ions within short time periods., QC 20130506

The stability of silver nanoparticles (Ag NPs) potentially released from clothing during a laundry cycle and their interactions with laundry-relevant surfactants [anionic (LAS), cationic (DTAC), and nonionic (Berol)] have been investigated. Surface interactions between Ag NPs and surfactants influence their speciation and stability. In the absence of surfactants as well as in the presence of LAS, the negatively charged Ag NPs were stable in solution for more than 1 day. At low DTAC concentrations (<= 1 mM), DTAC-Ag NP interactions resulted in charge neutralization and formation of agglomerates. The surface charge of the particles became positive at higher concentrations due to a bilayer type formation of DTAC that prevents from agglomeration due to repulsive electrostatic forces between the positively charged colloids. The adsorption of Berol was enhanced when above its critical micelle concentration (cmc). This resulted in a surface charge dose to zero and subsequent agglomeration. Extended DLVO theory calculations were in compliance with observed findings. The stability of the Ag NPs was shown to depend on the charge and concentration of the adsorbed surfactants. Such knowledge is important as it may influence the subsequent transport of Ag NPs through different chemical transients and thus their potential bioavailability and toxicity., QC 20130906

Implantation using stainless steels (SS) is an example where an understanding of protein-induced metal release from SS is important when assessing potential toxicological risks. Here, the protein-induced metal release was investigated for austenitic (AISI 304, 310, and 316L), ferritic (AISI 430), and duplex (AISI 2205) grades in a phosphate buffered saline (PBS, pH 7.4) solution containing either bovine serum albumin (BSA) or lysozyme (LSZ). The results show that both BSA and LSZ induce a significant enrichment of chromium in the surface oxide of all stainless steel grades. Both proteins induced an enhanced extent of released iron, chromium, nickel and manganese, very significant in the case of BSA (up to 40-fold increase), whereas both proteins reduced the corrosion resistance of SS, with the reverse situation for iron metal (reduced corrosion rates and reduced metal release in the presence of proteins). A full monolayer coverage is necessary to induce the effects observed., QC 20130614. Updated from submitted to published.

New insights are presented on the speciation of surface oxide phases on fine inert gas atomised (GA, <45 and <4 mu m) and water atomised (WA, <45 mu m) stainless steel AISI 316L powders. X-ray photoelectron and Auger electron spectroscopy, scanning electron microscopy, Raman spectroscopy, and cyclic voltammetry were applied for the characterisation. Oxidised manganese was strongly enriched in the outermost surface oxide of the GA powders (13 and 47 wt-%), an effect increasing with reduced particle size. Manganese and sulphur were enriched in oxide nanoparticles on the surface. Oxidised silicon (59 wt-%) was enriched on the WA powder surface. Tri-or tetravalent manganese oxides were observed on the GA particles in addition to alpha-Fe2O3, and Cr2O3. The oxide of the WA powder revealed in addition the likely presence of a silicate rich phase, mainly consisting of tetravalent Si, di- and/or trivalent Fe, and hexavalent Cr, which was confirmed not present as chromate., QC 20130604

Zinc release data from 5 years of unsheltered exposures in a marine and an urban site is compiled for different zinc material types. The thin surface treatment on zinc materials is gradually detached after approximately 2 years at both sites, revealing the pre-weathered zinc surface unprotected. This consequently increased the release rates of zinc from this surface, whereas the zinc runoff rate from the bare zinc sheet remained relatively stable. Raman studies on bare zinc sheet exposed for 5 years at the marine site revealed zinc oxide of varying crystalline nature and hydrozincite to appear localized and separated from each other., QC 20130524

An ion selective electrode (ISE) for determination of the labile silver ion concentration in carbonate containing solutions of pH 10 was seen to give incorrect results due to shifts in the Ag vertical bar Ag+ equilibrium. This drawback was not the case for the differential pulse anodic stripping voltammetry (DPASV) method., QC 20130311

Given the increasing incorporation of silver nanoparticles as an antibacterial additive in washing machines and textiles, sensitive methods for accurate determination of Ag+ ions in laundry relevant electrolytes (alkaline carbonate) are required. The most widely reported method, the silver ion selective electrode (ISE), lacked sensitivity and accuracy and was affected by the concentration of Na2CO3 in solution. Differential pulse stripping voltammetry (DPSV) on glassy carbon electrodes (GCE) was therefore investigated as an alternative technique. Surface preparation of the GCE surface was essential and a suitable procedure was developed. A linear response was observed from 0 to 180 mg L-1 with a lower detection limit of 500 ng L-1 (5 nM). DPSV was shown to be significantly more sensitive and accurate in determining the Ag+ activity than the silver ISE technique, particularly below 200 nM., QC 20130507

QC 20120712

The interaction between silvernanoparticles (Ag NPs) of different surface charge and surfactants relevant to the laundry cycle has been investigated to understand changes in speciation, both in and during transport from the washing machine. Ag NPs were synthesized to exhibit either a positive or a negative surface charge in solution conditions relevant for the laundry cycle (pH 10 and pH 7). These particles were characterized in terms of size and surface charge and compared to commercially laser ablated Ag NPs. The surfactants included anionic sodium dodecylbenzenesulfonate (LAS), cationic dodecyltrimethylammoniumchloride (DTAC) and nonionic Berol 266 (Berol). Surfactant–Ag NP interactions were studied by means of dynamic light scattering, Raman spectroscopy, zeta potential, and Quartz Crystal Microbalance. Mixed bilayers of CTAB and LAS were formed through a co-operative adsorption process on positively charged Ag NPs with pre-adsorbed CTAB, resulting in charge reversal from positive to negative zeta potentials. Adsorption of DTAC on negatively charged synthesized Ag NPs and negatively charged commercial Ag NPs resulted in bilayer formation and charge reversal. Weak interactions were observed for nonionic Berol with all Ag NPs via hydrophobic interactions, which resulted in decreased zeta potentials for Berol concentrations above its critical micelle concentration. Differences in particle size were essentially not affected by surfactant adsorption, as the surfactant layer thicknesses did not exceed more than a few nanometers. The surfactant interaction with the Ag NP surface was shown to be reversible, an observation of particular importance for hazard and environmental risk assessments., QC 20120201

A systematic comparison between the vibrational spectra in the CD and CH stretching regions of four deuterated and perprotonated surfactants adsorbed at the liquid/vapor interface has been carried out using vibrational sum frequency spectroscopy (VSFS). Bulk IR and polarized Raman spectra of hexane and its deuterated analogue have also been obtained for reference. Due to differences in the Fermi resonances, the relative positions and intensities of the spectral features, including conformational order indicators vary between the CD and CH regions. The commonly used sum frequency (SF) order indicator for perprotonated molecules, which involves the amplitude ratio of the symmetric CH3 r(+)/ symmetric CH2 d(+) bands is not directly transposable to the CD region. Instead, the ratio between the asymmetric CH3 r(-)/ antisymmetric CD2 d(-) bands is proposed as a more suitable alternative. Using as a starting point the SF spectra from the upright all-trans monolayer of dodecanol and its deuterated analogue, the theoretically modeling of the terminal methyl group orientation has been critically evaluated. The orientational analysis in the CD region gives significantly more reliable and consistent results, mainly because of the relative simplicity in unambiguously resolving the concerned peaks in the SF spectra., QC 20120228

Titanium oxide (rutile, TiO2) and zircon (ZrSiO4), known insoluble ceramic materials, are commonly used for coatings of implant materials. We investigate the release of zirconium, titanium, aluminum, iron, and silicon from different micron-sized powders of 6 powders of natural rutile (TiO2) and zircon (ZrSiO4) from a surface perspective. The investiga- tion includes five different synthetic body fluids and two time periods of exposure, 2 and 24 hours. The solution chemi- cals rather than pH are important for the release of zirconium. When exceeding a critical amount of aluminum and sili- con in the surface oxide, the particles seem to be protected from selective pH-specific release at neutral or weakly alka- line pH. The importance of bulk and surface composition and individual changes between different kinds of the same material is elucidated. Changes in material properties and metal release characteristics with particle size are presented for zircon., QC 20130502

The surface of aqueous solutions of 4-Nitro Benzo-15-Crown-5 (NB15C5) and Benzo-15-Crown-5 (B15C5) has been studied using the surface sensitive technique vibrational sum frequency spectroscopy (VSFS). The NO, CN, COC and CH vibrational modes of these compounds at the air-water interface as well as OH vibrational modes of the surface water hydrating this compound have been targeted in order to obtain molecular information about arrangement and conformation of the adsorbed crown ether molecules at the air-water interface. The CH2 vibrational modes of crown ethers have been identified and found to be split due to interaction with ether oxygen. The spectra provide evidence for the existence of a protonated crown complex moiety at the surface leading to the appearance of strongly ordered water species. The interfacial water species are influenced by the resulting charged interface and by the strong Zundel polarizability due to tunneling of the proton species between equivalent sites within the crown ring., Uppdaterad från Submitted till Published 20110615. QC 20100628

Iron, chromium, nickel, and manganese released from gas-atomized AISI 316L stainless steel powders (sized < 45 and < 4 mu m) were investigated in artificial lysosomal fluid (ALF, pH 4.5) and in solutions of its individual inorganic and organic components to determine its most aggressive component, elucidate synergistic effects, and assess release mechanisms, in dependence of surface changes using atomic absorption spectroscopy, Raman, XPS, and voltammetry. Complexation is the main reason for metal release from 316L particles immersed in ALF. Iron was mainly released, while manganese was preferentially released as a consequence of the reduction of manganese oxide on the surface. These processes resulted in highly complexing media in a partial oxidation of trivalent chromium to hexavalent chromium on the surface. The extent of metal release was partially controlled by surface properties (e.g., availability of elements on the surface and structure of the outermost surface) and partially by the complexation capacity of the different metals with the complexing agents of the different media. In general, compared to the coarse powder (< 45 mu m), the fine (< 4 mu m) powder displayed significantly higher released amounts of metals per surface area, increased with increased solution complexation capacity, while less amounts of metals were released into non-complexing solutions. Due to the ferritic structure of lower solubility for nickel of the fine powder, more nickel was released into all solutions compared with the coarser powder., QC 20111220

The oxidation of octadecanethiol (ODT, CH3-(CH2)17SH)-covered copper in dry air has been studied by in situ vibrational sum frequency spectroscopy (VSFS), infrared reflection absorption spectroscopy (IRAS), and cathodic reduction (CR). During the first 10 h of exposure, the VSF spectral line shape in the CH stretching region changed significantly, with resonances observed as dips being transformed into peaks. This was attributed to a phase change in the nonresonant sum frequency signal due to the formation of a thin layer of copper(I) oxide beneath the ODT. Complementary cathodic reduction and infrared reflection/absorption spectroscopy studies yielded a thickness of the oxide layer of <2 nm after 19 h exposure. An orientation analysis on the adsorbed molecules by VSFS indicated a decreased tilt angle of the terminating methyl groups with respect to the surface normal during the formation of the oxide layer., QC 20120207