Search

• Waste production from schools changes depending on the level of institutions. • High rate of positive answers but unsuccessful sorting indicate lack of practice. • Recycling capture rates do not differ significantly between school types. • There is a strong positive correlation between capture rates of some recyclables. • The success of recycling is higher if it is is supported with specific programmes. In this study, the waste generation at the educational institutes chosen from four different levels (kindergartens, primary, secondary and high schools) in Istanbul was measured on-site and the contents of the waste thrown into the recycling bins were determined to specify capture rates. Separation and weighing processes were performed at 16 spots in high schools, 12 spots in secondary schools, 7 spots in primary schools and 7 spots in kindergartens. A survey was conducted to determine the students' awareness of recycling in these schools. It was revealed that the wastes produced from educational institutes are organics (36.4 %), paper (24 %), plastics (14.4 %), glass (8.1 %), metals (4.8 %) and miscellaneous (12.3 %). The survey results indicate that 93 % of the participants think recycling is important, 71 % of them throw their waste into suitable waste bins and 59 % of them know the location of the recycling bins. At the primary school level, a very high rate of paper waste (92.3 %) was reported in plastic bins while plastic waste collected in these bins remained only 5.7 %. It was also seen that glass waste captured in glass bins and metal waste in metal bins remain very low rates (20.9 % and 29.2 %, respectively) at the secondary school level. At the high school level, it was determined that the most commonly captured wastes in glass, plastics and paper bins are glass (47.5 %), plastic (43.2 %) and paper (32.5 %), respectively. Correlation analyses indicated a high positive correlation (p < 0.05) between particular types of waste. [ABSTRACT FROM AUTHOR]

Due to a shortage of resources, exploring new biomass fillers has become critical for paper making. In this study, we reported an eco-friendly strategy for fabricating low-cost and efficient recycled paper with high mechanical properties using corrugated cardboard waste paper and harmless municipal sludge (HMS). First, the characteristics of HMS, including the particle size, pH, specific surface area, organic functional groups and organic component content, were analyzed. Then, the influence of the amount of HMS on the properties of the recycled paper was studied. Finally, the strengthening mechanism of biomass filling recycled paper was discussed. The results showed that HMS, a biomass filler for recycled paper preparation, exhibited excellent physical and chemical properties, with a median particle size of 6.395 μm, a surface area of 39.974 m2 g−1 and organic functional groups. The tensile index of the recycled paper with 30 % HMS was 13.10 Nm/g, which was 16.4 % greater than that of the unfilled paper and showed better thermal stability. This excellent performance could be attributed to the uniform distribution of HMS on the fiber surface, which improved the accessibility of hydrogen bond formation between fibers. Thus, this study proved that HMS was an excellent biomass filler for producing recycled paper. [ABSTRACT FROM AUTHOR]

Metagenomics has revolutionized access to genomic information of microorganisms inhabiting the gut of herbivorous animals, circumventing the need for their isolation and cultivation. Exploring these microorganisms for novel hydrolytic enzymes becomes unattainable without utilizing metagenome sequencing. In this study, we harnessed a suite of bioinformatic analyses to discover a novel cellulase-degrading enzyme from the camel rumen metagenome. Among the protein-coding sequences containing cellulase-encoding domains, we identified and subsequently cloned and purified a promising candidate cellulase enzyme, Celcm05-2, to a state of homogeneity. The enzyme belonged to GH5 subfamily 4 and exhibited robust enzymatic activity under acidic pH conditions. It maintained hydrolytic activity under various environmental conditions, including the presence of metal ions, non-ionic surfactant Triton X-100, organic solvents, and varying temperatures. With an optimal temperature of 40 °C, Celcm05-2 showcased remarkable efficiency when deployed on crystalline cellulose (> 3.6 IU/mL), specifically Avicel, thereby positioning it as an attractive candidate for a myriad of biotechnological applications spanning biofuel production, paper and pulp processing, and textile manufacturing. Efficient biodegradation of waste paper pulp residues and the evidence of biopolishing suggested that Celcm05-2 can be used in the bioprocessing of cellulosic craft fabrics in the textile industry. Our findings suggest that the camel rumen microbiome can be mined for novel cellulase enzymes that can find potential applications across diverse biotechnological processes. [ABSTRACT FROM AUTHOR]

Xylanase finds extensive applications in diverse biotechnological fields such as biofuel production, pulp and paper industry, baking and brewing industry, food and feed industry, and deinking of waste paper. Here, polyethylene glycol (PEG)-phosphate aqueous two-phase system (ATPS) was applied for the purification of an alkaline active and thermotolerant xylanase from a marine source, Cladophora hutchinsiae (C. hutchinsiae). In the purification process, the effects of some experimental factors such as PEG concentration and PEG molar mass, potassium phosphate(K2HP04) concentration, and pH on xylanase distribution were systematically investigated. Relative enzymatic activity and purification factor obtained were 93.21% and 7.18, respectively. A single protein band of 28 kDa was observed on SDS-PAGE. The optimum temperature and pH of xylanase with beechwood xylan were 30 °C and 9.0, respectively. The Lineweaver-Burk graph was utilized to determine the Km (4.5 ± 0.8 mg/mL), Vmax (0.04 ± 0.01 U) and kcat (0.001 s−1) values of the enzyme. It was observed that the purified xylanase maintained 70% of its activity at 4 °C and was found stable at pH 4.0 by retaining almost all of its activity. Enzymatic activity was slightly enhanced with Na+, K+, Ca2+ and acetone. The highest increase in the reducing sugar amount was 53.6 ± 3.8, for orange juice at 50 U/mL enzyme concentration. [ABSTRACT FROM AUTHOR]

The current research focuses on the efficiency of energy recovery from non-hazardous organic wastes. It entails the generation of low-chloride refuse-derived fuel (RDF) from municipal solid waste (MSW) through moderate pyrolysis of combustible components. The moderate pyrolysis settings and composition ratio of biogenic/non-biogenic content from MSW combination (food waste, plastic waste, and paper waste) had a significant impact on the thermochemical characteristics and fuel behavior of RDF. Furthermore, pyrolysis with optimal MSW composition was studied to reduce toxic elements (chlorides, sulphides, and nitrides) and enhance the energy value in RDF by utilizing potassium-rich (waste orange peels (OP); banana peels (BP); and maize cob (MC)) and calcium-rich species (waste animal bone meal (ABM); egg shells (ES); and mussel shells (MS)) as natural additives. The results showed that increasing the pyrolysis temperature maximized the carbon concentration with reduced oxygen moieties (low O/C ratio), indicating a high energy value as the oxygenates were eliminated during moderate pyrolysis. The RDF treated at 400 °C (SF4-400) with MSW composition of 55% non-biogenic carbon and 45% biogenic carbon resulted in HHV of 29.22 MJ kg−1, the lowest ash concentration (0.96%), and a densified microstructural surface. The addition of natural maize cob additive into MSW (SF4-400-MC) yielded the maximum HHV (33.07 MJ kg−1) with considerable reductions in chlorides (71.43%), sulphides (87.50%), and insignificant nitrides content, all of which meet ASTM RDF quality criteria Grade I. [ABSTRACT FROM AUTHOR]

This paper reports an innovative study that aims to address key issues in the efficient recycling of wastepaper cellulose. The research team utilized the temperature-responsive upper critical solution temperature (UCST) polymer P(NAGA-b-DMA) in combination with the LytA label's affinity for choline analogs. This innovative approach enabled them to successfully develop a novel soluble immobilized enzyme, P(NAGA-b-DMA)-cellulase. This new enzyme has proven highly effective, significantly enhancing the degradation of wastepaper cellulose while demonstrating exceptional stability. Compared with the traditional insoluble immobilized cellulase, the enzyme showed a significant improvement in the pH, temperature stability, recycling ability, and storage stability. A kinetic parameter calculation showed that the enzymatic effectiveness of the soluble immobilized enzyme was much better than that of the traditional insoluble immobilized cellulase. After the immobilization reaction, the Michaelis constant of the immobilized enzyme was only increased by 11.5%. In the actual wastepaper degradation experiment, the immobilized enzyme was effectively used, and it was found that the degradation efficiency of wastepaper cellulose reached 80% of that observed in laboratory conditions. This novel, thermosensitive soluble immobilized cellulase can efficiently catalyze the conversion of wastepaper cellulose into glucose under suitable conditions, so as to further ferment into environmentally friendly biofuel ethanol, which provides a solution to solve the shortage of raw materials and environmental protection problems in the paper products industry. [ABSTRACT FROM AUTHOR]

The main part of companies in Bulgaria are built, however in the 70s, and upgraded last decade. The country supplies around 80 % of its supplies of paper, paperboard and pulp with own production. Integrated treatment of wastes is a priority for realizing closed life cycle of materials. The aim of the present work is to investigate the composition and other important characteristics of biomass wood ash wasted from paper industry. The correlations and associations among the chemical characteristics are also studied to find some basic trends and important relationships between two similar wastes from different enterprises. It was proved that all samples taken contained Ba, Cr, Mn, Ni, Co, Al, Fe, Cu and Zn far below the legal limits for such type of products. A product has a certain anti-acidic effect. The other positive result was that the content of iron is between 34 to 60 mg per 1 kg dry waste. The microscopic photos confirmed that the particles are close to the nano-size materials. The content of the elements C, N, H is in good quantities and ratios, which is a prerequisite for their use as a soil improver. By the results of this study, it was confirmed that all samples produced as a result of the thermal treatment and final low water content achieved are free from pathogen microorganisms and different weed seeds, affecting the yield and soil sustainability. That allows determining the optimal ratio between the used components with a view to obtain products with desired thermal stability and physico-chemical properties as soil improvers. [ABSTRACT FROM AUTHOR]

Enzymes derived from microbial sources have gained increasing popularity in industrial applications over the past decades. Despite the high production cost, alkaline proteases have wide applications in industries such as tanneries, food production, and detergents. In recent years, there has been a shift towards utilizing natural carbon sources for cultivating microorganisms and extracting proteases in order to reduce production costs. This study aimed to investigate the biochemical and kinetic properties of protease enzymes obtained from Aspergillus niger cultivated in a paper waste medium and compare with the enzyme produced in a basal medium. Glucose is a more favorable carbon source compared to cellulose, so paper waste was pretreated with cellulose-degrading bacteria to convert cellulose into smaller carbohydrates. After the growth of A. niger in basal and combinational media, the enzymatic properties were compared between the extracted enzymes by using casein as substrate. The results demonstrated that A. niger could produce protease enzymes in the paper waste medium similar to the basal medium with more than 5-fold cost saving. The specific activity of the enzymes isolated from the basal and paper waste media was calculated to be 184.95 ± 10.56 U ml−1 and 169.88 ± 11.05 U ml−1, respectively. Carbon sources did not affect the optimum pH and temperature of the protease enzyme, which were found to be 8 and 37 °C, respectively. This study provides valuable insights into the production of alkaline protease from A. niger using a combinational medium (paper waste pretreated by cellulose-degrading bacteria), offering a cost-effective approach for industrial applications. [ABSTRACT FROM AUTHOR]

Selective enrichment of La(III) by green material as an industrial raw material is of great research interest. In this study, the selective interaction between P and La(III) was utilized, and waste paper (WP) modified with phytic acid (PA) was used to adsorb La(III) from water using a simple one-pot method. The adsorption capacity was 237.23 mg g−1 (30 °C, pH = 5, initial concentration of 200 mg L−1). The equilibrium isotherm fitted the Langmuir isotherm model well. The adsorption equilibrium was reached after 15 min. The adsorption kinetics followed the pseudo-second-order kinetic model, indicating that the adsorption mechanism of the material towards La(III) is single-layer chemisorption. It selectively adsorbed La(III) from four coexisting substances (Pb, Ni, Cu, and Co). After six cycles, the adsorption efficiency of the adsorbent material remained at 60%. [ABSTRACT FROM AUTHOR]

Socio-ecological theories have long been in search of general principles to characterise anthropogenic activity-environmental change dynamics. Besides allowing for more flexible hypothesis testing, stochastic-extended IPAT and ImPACT baselines opened the door to multiple environmental applications in which solid waste generation took a growing stage. This paper surveys Waste Kuznets Curve's original foundations and underlines why the nature and shape of the hypothetical curvilinear income-waste response function tend to compare to a "black-box". It then stresses why diverging conclusions are linked to heterogeneous estimators' choices differing in their statistical assumptions and powers; whereas generic patterns hardly emerge (e.g., income elasticities of waste generation vary even when the mathematical functional form does not; population elasticities are sensitive to time-varying data and income groups). Next, we identify persisting biases of endogeneity which threaten the internal validity of WKC conclusions, if uncontrolled for (e.g., simultaneity, waste measurement errors and garbage policy confounding effect); along with other identification problems including within-panel heterogeneity with systematic slope variations and cross-sectional and spatially dependent income series. Although we propose a set of theoretically justified instrumental variables to exogenously predict income levels and ensure unbiased elasticities, we also detect and underline that additional threats to external invalidity do play out in practice (e.g., asymmetric geographical coverage and bias of case study selection due to environmental data constraints; missing policy-realm; within-waste heterogeneity hidden by widely aggregated indicators; and a non-systematic treatment of the technological effect). All prevent the waste literature from converging and should be considered by future empirical assessments. [ABSTRACT FROM AUTHOR]

The growing demand for environmentally friendly and sustainable materials has led to the invention of innovative solutions aiming to reduce negative impacts on the environment. Mycelium-based green composites (MBCs) have become an alternative to traditional materials due to their biodegradability and various potential uses. Although MBCs are accepted as modern materials, there are concerns related to some of their physical and mechanical properties that might have limitations when they are used. This study investigates the effects of using paper waste to improve MBC properties. In this study, we investigated the physical and mechanical properties of MBCs produced from lignocellulosic materials (corn husk and sawdust) and mushroom mycelia of the genus Lentinus sajor-caju TBRC 6266, with varying amounts of paper waste added. Adding paper waste increases the density of MBCs. Incorporating 20% paper waste into corn husks led to the enhancement of the compression, bending, and impact strength of MBCs by over 20%. Additionally, it was also found that the MBCs produced from corn husk and 10% paper waste could help in reducing the amount of water absorbed into the material. Adding paper waste to sawdust did not improve MBC properties. At the same time, some properties of MBCs, such as low tensile strength and high shrinkage, might need to be further improved in the future to unlock their full potential, for which there are many interesting approaches. Moreover, the research findings presented in this publication provide a wealth of insightful information on the possibility of using paper waste to improve MBC performance and expand their suitability for a range of applications in sustainable packaging materials and various home decorative items. This innovative approach not only promotes the efficient utilization of lignocellulosic biomass but also contributes to the development of environmentally friendly and biodegradable alternatives to traditional materials. [ABSTRACT FROM AUTHOR]

Thiophene sulfide is difficult to be removed by hydrodesulfurization. In this study, ZnCl2-waste paper fiber activated carbon was used as adsorbent to remove thiophene sulfide from simulated oil by hydrothermal modification. Under the optimum condition of ammonia modification, the adsorption capacity of modified adsorbent to BT is 14.8 mg S/g, 2.98 times that of unmodified. BET, FTIR and Boehm analysis showed that the mesopore volume of ammonia modified adsorbent increased by 96.62% and the mesopore ratio increased from 12.58% to 43.40%, which was conducive to improving the adsorption rate. After modification, the basic groups on the surface of the adsorbent increased by 44.3 times, and –NH3+, –OH and –NH2 enhanced the electron attraction and hydrogen bonding force between the adsorbent and BT molecule. Adsorption isotherms, adsorption kinetics and adsorption thermodynamics show that the adsorption process is spontaneous, entropic and exothermic. The pseudo-second-order kinetic rate constant increases with the increase of adsorption temperature, indicating that the increase of temperature is beneficial to accelerate the adsorption rate. The adsorption desulfurization process follows the mechanism of single and multilayer adsorption mixing. The results of this study can help to reveal more clearly that biobased activated carbon can be modified to adsorb thiophene sulfide. Ammonia modified adsorbents enhance the adsorption capacity for benzothiophene [ABSTRACT FROM AUTHOR]

This study evaluated the production of marine biodegradable plastics, specifically polyhydroxyalkanoates (PHAs), using waste paper from food containers as a novel material source. The results showed that adding dilute sulfuric acid as a pretreatment may have a negative impact on enzyme hydrolysis efficiency. Without pretreatment, the highest glucose concentration was observed in the 50-min heating group. In the experimental group with 1% dilute sulfuric acid as a pretreatment, the highest average glucose concentration was observed in the 25-min treatment group. In flask scale experiments, the C/N ratio was controlled at 10, 20, and 30. The results showed that when the C/N ratio was 10, the PHA/CDM ratios were 16.3 and 23.6 at 48 and 72 h, respectively. After 96 h of cultivation using hydrolysis liquid from the waste paper container as the sole carbon source in a 5-L scale experiment, the PHA/CDM ratio was 28.7 and the PHA concentration was 0.95 g/L. The potential bacterial strain in this study was confirmed to be a Bacillus genus bacterium after strain identification. The signal peaks indicated that the PHA obtained from the Bacillus sp. production process was PHB. [ABSTRACT FROM AUTHOR]

Purpose: To assess the extent of paper waste generated per year by instructions for use (IFUs) brochures included in intraocular lens (IOL) packaging in Europe and the U.S. Setting: Rothschild Foundation Hospital, Paris, France; Royal Free London NHS Foundation Trust; Center for Sight, London, United Kingdom. Design: Experimental study. Methods: A sample of IOLs were collected and each IFU was weighed. In addition, the cumulative weight of these brochures used in cataract surgeries performed annually in Europe and the U.S. was estimated, and the potential annual paper conservation that could be achieved if all manufacturers adopted electronic IFUs (e-IFUs) in Europe and the U.S. was determined. Results: The mean and standard deviation of the weight for overall IFUs, classic IFUs, and e-IFUs were 17.6 ± 13.8 g, 23.5 ± 13.2 g, and 2.9 ± 1.9 g, respectively. The estimated cumulative weight of paper generated from the IFUs accompanying implants used in European and U.S. cataract surgeries is 153 tons. If all manufacturers transition to e-IFUs, the cumulative weight saved would be 128 tons (-84%), equivalent to 120 tons of carbon dioxide equivalent and the preservation of more than 2000 trees annually. Conclusions: The classic IFUs in IOL packaging result in a significant amount of paper waste annually. Therefore, there is an urgent need for a rapid transition to e-IFU technology. The adoption of e-IFUs has already been authorized in Europe and the U.S., and it is crucial to expedite this process. [ABSTRACT FROM AUTHOR]

Complex polymers represent a challenge for remediating environmental pollution and an opportunity for microbial‐catalysed conversion to generate valorized chemicals. Members of the genus Streptomyces are of interest because of their potential use in biotechnological applications. Their versatility makes them excellent sources of biocatalysts for environmentally responsible bioconversion, as they have a broad substrate range and are active over a wide range of pH and temperature. Most Streptomyces studies have focused on the isolation of strains, recombinant work and enzyme characterization for evaluating their potential for biotechnological application. This review discusses reports of Streptomyces‐based technologies for use in the textile and pulp‐milling industry and describes the challenges and recent advances aimed at achieving better biodegradation methods featuring these microbial catalysts. The principal points to be discussed are (1) Streptomyces' enzymes for use in dye decolorization and lignocellulosic biodegradation, (2) biotechnological processes for textile and pulp and paper waste treatment and (3) challenges and advances for textile and pulp and paper effluent treatment. [ABSTRACT FROM AUTHOR]

Cellulose hydrogel derived from cellulose fibers extracted from printed paper waste is prepared. The hydrogel derived from 3 wt% of the cellulose concentration exhibits a maximum water absorption capacity of 465.5%. The effects of the cellulose hydrogel on the soil moisture are evaluated using four types of soils namely river sand, clayey soil, loamy soil, and gley soil (the wetland soil). The potential application of cellulose‐based hydrogel as an eco‐friendly seed germination media of the paddy seeds under the soil‐less condition is evaluated. This study shows that paddy seeds exhibit a higher seed germination rate of 53% when cellulose hydrogel is used as a seed germination media as compared to seed germination rate ranging from 14% to 35% when various types of soil are used as the germination media. The prepared cellulose hydrogel could be applied as an eco‐friendly and cost‐effective seed germination media to enhance the paddy seeds' germination rate. [ABSTRACT FROM AUTHOR]

Mathematical modeling is a high-leverage topic; it is critical to students' participation in STEM education and supports civic engagement. Until recently, research on modeling at the elementary level has been underemphasized, particularly research on supports and challenges for teachers who engage in designing authentic modeling tasks. In this study, we employed qualitative case study methods to investigate how elementary teachers designed and implemented authentic mathematical modeling tasks, with an explicit focus on how their tasks evidenced different dimensions of authenticity. We analyzed three cases of teams of elementary teachers as they developed modeling tasks connected to school and community contexts. The three cases were: 1) a student-driven modeling task related to paper and plastic waste in a school cafeteria, 2) a modeling task based on authentic situations at a community-run resource center, and 3) a modeling task focused on designing and monitoring a school community-building art project. Our cases illustrate that elementary teachers can successfully design and implement modeling activities that utilize different entry points and evidence multiple dimensions of authenticity. Furthermore, we found that the specific dimensions of authenticity may vary depending on the design supports and curriculum challenges within each context. [ABSTRACT FROM AUTHOR]

This study focused on the co-fermentation of food waste and tissue paper to produce ethanol, which will eliminate the need for additional nitrogen sources and nutrients, thereby reducing production costs. In response to the inhibitory effect of the high concentrations of glucose present in mixed-substrate hydrolysates on xylose fermentation, a co-fermentation process using Saccharomyces cerevisiae and Candida shehatae was proposed. This approach reduced the fermentation time by 24 h, increased the xylose utilization rate to 88%, and improved the ethanol yield from 41% to 46.5%. The impact of external conditions and corresponding optimization were also analyzed in this process. The optimum conditions were a 1:3 ratio of Saccharomyces cerevisiae to Candida shehatae, a pH of 5, and shaking at 150 r/min, and by employing dynamic temperature control, the ethanol production was increased to 21.98 g/L. Compared to conventional processes that only use Saccharomyces cerevisiae, this method enhanced the ethanol yield from 41% to 49%. [ABSTRACT FROM AUTHOR]

The rapid increase in solid waste along with urbanisation, especially arising from the industrial and agricultural sectors, sparks concern from the public regarding their adverse impact on human and environmental wellness. Therefore, waste biorefinery is the current interest that aligns with the concept of 'waste-to-wealth'. The conversion of waste into valuable products such as cellulose nanocrystals (CNCs) is an alternative method of circular waste management as CNCs have various applications. Their non-toxicity, biocompatibility, excellent mechanical strength, and load-bearing properties render them a good reinforcement agent for packaging films, sensors, and scaffolds. Nonetheless, the lack of studies on the comparison of waste sources and the complex parameters for the extraction of CNCs hinders the development of CNC extraction from waste products. This review paper compares and organizes the information from previously published scientific papers and reports on waste product sources, methods, parameters, and environmental effects of the derivation of CNCs from waste. Previously, no thorough reviews have been done closely on the sustainability aspect of CNC extraction from waste products. Through this review, it shows that there is a positive trend where novel CNC extraction routes are discovered to improve the yield, environmental friendliness, performance, and cost. However, most of the studies did not specify the environmental impacts of the extraction routes, limiting their feasibility for conventional applications. [ABSTRACT FROM AUTHOR]

Composite materials have been widely used because of their superior properties compared to those of the original material. Separation of the constituent materials is not easy in the recycling process, and such an effort lowers economic viability. As such, this study employed a pyrolysis as a valorizing method for the composite material. Disposable paper cup waste (DPCW) was chosen as the model compound for paper-plastic composites. To offer green/sustainable features, CO2 was employed as a raw and reactive material in the pyrolysis process. It was proved that DPCW primarily composed of cellulose (outer layer) and polyethylene (inner layer). In the single-stage and multistage pyrolysis of DPCW, the CO2 reactivity in the homogeneous reaction of CO2 and DPCW-derived volatiles was not rapid. To accelerate the reaction kinetics governing the reactivity of CO2, the catalytic pyrolysis of DPCW over Ni/SiO2 was performed. The formation of syngas increases significantly, suggesting that CO2 reactivity was catalytically enhanced. The generation of syngas (enhanced by CO2) was inversely related to the DPCW oil generation, indicating that more carbon was assigned from the oil to the gaseous pyrogenic products. The study results would offer a strategic means to valorize paper-plastic composites and CO2 into energy through pyrolysis. [ABSTRACT FROM AUTHOR]

The research on the recovery of low-grade thermal energy carried away by boiler flue gas is significant for sugar mills. This paper designs a waste heat recovery system based on sugar plant flue gas, integrating absorption refrigeration cycle and the organic Rankine cycle, and the effects of nine working fluids on the system are investigated. The aim is to realize the multi-form conversion of energy. The performance of the system is evaluated in terms of energy, exergy, and economic metrics. Multi-objective optimization is performed with the method of the NSGA-II genetic algorithm. The results show that Butane is the most suitable working fluid for ORC. The exergy efficiency of the system is 32.125% before optimisation, with an increased space cooling capacity of 15820.56 MW per year for the sugar mill. The exergy destruction analysis of the system reveals that the generator accounts for the highest proportion of exergy destruction (50.8%). The entire system shows the LCOE is as low as 0.0406$/kWh under the optimized condition. The optimized system can obtain an estimated annual electricity sales revenue of $136,300, and the sugar mill can save $308,600 in cooling costs. In addition, the payback period can be shortened to 5.79years. [ABSTRACT FROM AUTHOR]

The study assessed quality of briquettes produced from bagasse (B), corn husk (CH), and cassava roots (CR) using banana peels (BP), wastepaper (WP), and clay soil (CS) as binders. Mixing ratios were established from carbonized materials, and briquettes physical and combustion properties were determined. Weak shatter resistance appeared in WP, CS briquettes had best tumbling resistances while WP briquettes had better water penetration. CS briquettes (3:1:1) had low (2.7%) moisture content (MC), and 1:3:1 had low (28%) volatile matter (VM) while the highest was 41% for 2:2:1. Ash content (AC) for 2:2:1 was the highest (41%) with highest heating value (HV). BP briquettes for 0:4:1 (CH:CR:BP) had the lowest MC (4.9%), whereas 2:2:1 (B:CH:BP) had the highest VM (41.5%). AC (15.5%) for 1:3:1 was the highest while 2:2:1 (CH:CR) had the highest HV. WP briquettes 1:3:1 (B:CH) had the lowest MC (2%) and 3:1:1 had highest VM (35%), while the highest AC appeared for 4:0:1. The 2:2:1 (B:CR:WP) briquette yielded the highest HV (25.5 MJ/Kg). All materials were suitable for briquetting, although their qualities are sensitive to weather conditions. Together with BP briquettes, WP briquettes 2:2:1 (B:CR:WP) produce the best results, especially when using CR and CH feedstocks. [ABSTRACT FROM AUTHOR]

This article presents the results of the study of the morphological composition of municipal solid waste (MSW) from the landfill of Atyrau city, and the waste's energy characteristics and presence of microorganisms, including bacteria, fungi and viruses. This study was carried out under a government order to determine the feasibility of recycling accumulated and incoming waste into electricity and its hazard to the environment and the workers involved in handling it. At the moment, there is no MSW recycling in Kazakhstan, which has led to the accumulation of more than 125 million tons of waste with an annual increase of 5 million tons. The research included four major cities (Almaty, Shymkent, Atyrau and Astana), which were selected not only on the basis of population, but also because the cities were located in different climatic zones. Samples were collected at the city landfills: 10 samples with an average distance of 100 m from each other were collected to provide a maximum coverage of both recently received waste and long-time stored waste. The research showed that neither climatic conditions nor the population size had a significant impact on MSW density, the values of which ranged from 120.1 kg/m3 to 145.4 kg/m3, as this indicator directly depends on the quality of life. The mass of the combustible fraction ranged from 39.41% to 54.62% and was mainly represented by plastic, textile and paper waste. The average value for the four cities was 50.30%. The higher calorific value fell in the range of 24.22–30.49 MJ/kg, with an average value of 26.71 MJ/kg. Microbiological studies showed little difference in average composition regardless of climatic conditions. Thus, no sharp differences in MSW composition, its energy characteristics and microbiological composition were found. The results of this study may be useful for optimising MSW recycling and disposal processes, as well as for developing measures to reduce their negative impact on the environment and human health. [ABSTRACT FROM AUTHOR]

Indonesia has the highest number of active volcanoes in the world due to its geologic location at the confluence of the Eurasian and Australian plates. However, despite this, the knowledge of local communities regarding volcanic eruptions is still very minimal. Therefore, it is important to provide education to the community in this context is the local community. This Community Service Program aims to increase community knowledge related to the process of volcanic eruption by using pulp-based learning media, so that it can become disaster mitigation knowledge. The methods used are observation, coaching or training based on practical simulations, questionnaires and interviews. The subject of this Community Service is the community of Tambun village, Baolan sub-district, Tolitoli district, totaling 21 people in collaboration with students of the elementary school teacher education program in semester III. The results of this program are the increase in community knowledge related to volcanic eruptions and the growth of community awareness related to the use of waste paper, this is in line with SDGs 4 and SDGs 17 relating to quality education and partnerships with the community.

Geopolymer concrete has been developed as a means of reducing carbon dioxide (CO2) emissions due to concrete manufacturing, which account for around 5-10% of the total global CO2 emissions. Additionally, this innovative material aims to utilize industrial waste as a sustainable resource. This study concentrates on developing a geopolymer mortar composition comprising 70% fly ash and 30% metakaolin. The mixture also includes 14 molars of sodium hydroxide, sodium silicate, saturated surface dry sand, water at a volume of 10% of the mix, and 1.5% superplasticizer. The solution-to-solid materials ratio was established at 0.55 while the ratio between sodium silicate and sodium hydroxide was established at 2.5:1. The geopolymer mortar was enhanced by rice husk fibers at varying volume percentages of 1%, 1.5%, and 2%. Additionally, waste paper, in the form of paper ash, was introduced as filler at a volume percentage of 5%. Following the demolding process, the specimens were cured in the controlled environment of an oven, with the temperature set at 60 °C for a period of 24 hr. Subsequently, the cured samples were stored for 7 and 28 days and then were tested. When different amounts of rice husk fibers were mixed in with a fixed amount of 5% paper ash, the flexural resistance of the geopolymer mortar increased significantly. After 7 days of curing, it was seen that the flexural strength experienced an increase of 4%, 13%, and 25%, and a further increase of 11%, 18%, and 31% after 28 days of curing. The results of the impact test showed a notable enhancement in impact resistance and energy absorption when incorporating paper ash and rice husk fibers. Specifically, the initial crack results exhibited a 50% rise, while the specimen failure after 28 days of curing showed a 66% improvement. [ABSTRACT FROM AUTHOR]

This study assesses the mechanical properties of mortars incorporating waste paper sludge-derived cellulose fibers. Compression and flexural tests were carried out on specimens prepared with cellulose fibers at different proportions, ranging from 0% to 2% of the total weight of the solid mortar constituents (cement, sand, and lime). In addition, a comparative analysis was carried out to evaluate the influence of the preparation method on the mechanical properties of the mortars. To this end, two series of mortars were studied: one prepared following a rigorous control of the preparation parameters and the other made without systematic parameter control to simulate typical on-site conditions. Finally, the applicability of both traditional and eco-friendly mortars in the construction of small-scale masonry walls was assessed through compression tests. Overall, the mechanical properties of mortars with cellulose fibers were comparable to those with 0% waste material, regardless of the production process. Regarding the compressive behavior of masonry walls, experimental tests showed significant similarities between specimens made with traditional and eco-friendly mortar. In conclusion, incorporating cellulose fibers into cement-based mortar shows considerable potential for building applications, enhancing the environmental benefits without compromising the mechanical behavior. [ABSTRACT FROM AUTHOR]

Lignocellulosic biomass holds promise as a renewable feedstock for various applications, but its efficient conversion requires cost-effective degradation strategies. The main objective of this study was to investigate the effect of the growth conditions of Cellulomonas phragmiteti in the production of (hemi)cellulosic supernatants. To meet this aim, different lignocellulosic residues were used as carbon sources for growth using defined mineral or nutritive culture media. Cell-free culture supernatants with xylanolytic activity were produced in all the conditions evaluated, but the highest xylanase activity (15.3 U/mL) was achieved in Luria–Bertani (LB) medium containing 1% waste paper. Under these conditions, almost negligible β-glucosidase, cellobiohydrolase, β-xylosidase, and α-arabinofuranosidase activity was detected. The xylanolytic supernatant showed tolerance to salt and displayed maximal catalytic efficiency at pH 6 and 45 °C, along with good activity in the ranges of 45–55 °C and pH 5–8. As it showed good stability at 45 °C, the supernatant was employed for the hydrolysis of birchwood xylan (50 g/L) under optimal conditions, releasing 10.7 g/L xylose in 72 h. Thus, C. phragmiteti was found to produce a xylanolytic enzymatic supernatant efficiently by utilizing the cheap and abundant lignocellulosic residue of waste paper, and the produced supernatant has promising attributes for industrial applications. [ABSTRACT FROM AUTHOR]

Pyrolysis of medical waste components combined via a novel systematic combination approach (sequentially binary, ternary, and quaternary copyrolysis) was conducted at 400°C to investigate the synergy between medical waste components in improving chemical characteristics and yields of pyrolytic oil. Pyrolysis of hydrocarbon-polymer-containing materials such as medical gloves and rubber bands produced more than 30% of liquid products with substantial compositions of saturated aliphatic hydrocarbon polymers. On the other hand, moisture- and carbonyl-rich pyrolytic liquid products with low selectivity were obtained from pyrolysis of lignocellulosic biomass waste such as HVS paper (houtvrij schrijfpapier, meaning "writing paper made from wood pulp") and garden waste. Binary copyrolysis of lignocellulosic biomass and medical gloves exhibited improvement on pyrolytic liquid yield and selectivity toward saturated aliphatic hydrocarbon polymers due to hydrogen donor as the medical glove fraction became dominant. The addition of rubber band to the mixture of HVS paper and medical face masks enhanced the pyrolytic liquid yield. The pyrolysis of the mixture of HVS paper, medical face masks, medical gloves, and either rubber bands or cotton fabrics with mixture ratio of 60:20:10:10 yielded the most optimum pyrolytic liquid yield with significant distribution of alkanes in the pyrolytic liquid products. [ABSTRACT FROM AUTHOR]

As the construction of high-rise buildings increases to solve residential spaces caused by high density population concentration, the occurrence of fire accidents in high-rise buildings is also increasing. The primary cause of fire damage in high-rise buildings is the spread of fire caused by exterior wall finishes. Therefore, it is essential to develop semi-non-combustible finishes that can be applied to high-rise buildings to prevent the spread of fire due to exterior wall finishes. To address this issue, numerous studies are being conducted to develop flame retardant finishing materials that reduce heat release rate and total heat release. A double flame retardant mixed waste paper with expandable graphite and magnesium hydroxide was manufactured to improve the fire performance of cellulose building finishing materials. Total heat release (THR), CO, and CO2 Generation changes were measured using a cone calorimeter, and thermal diffusion rate was measured through the LFA 1000 experiment. The correlation of total heat release, CO generation, CO2 generation, and mass reduction rate by variation of expandable graphite's mesh size at double flame-retardant waste paper were secured through a cone calorimeter test. The thermal diffusion rate data of the specimen were secured through the LFA 1000 experiment. Through experiments, it has been confirmed that specimens using specific expandable graphite particles can be utilized as fire-resistant finishing materials in construction, ensuring fire resistance performance. [ABSTRACT FROM AUTHOR]

Microbial-induced calcite precipitation (MICP) is an innovative technology in civil engineering. However, the high cost of components and the fragility of the treated soil limit its wide use. One of the possible solutions is organic waste incorporation at different stages of the technology. In the present study, we consider the use of spent brewer's yeast (BSY) to produce bacterial inoculates and wastepaper, flax shives and sawdust as reinforcing additives into the soil. We showed that the replacement of expensive components of LB medium by BSY extract increased biomass growth characteristics of Bacillus subtilis K51, B. cereus 4b and Micrococcus luteus 6 strains by 1.4, 1.5 and 1.8 times, respectively, while for B. subtilis 168, they were comparable to LB medium. The urease activities of all strains were not reduced compared to the control. Among the three kinds of cellulose-containing waste, wastepaper incorporation into MICP-treated soil samples led to an increase in compressive strength by 2.1 times and precipitated calcite percentage by almost 1.5 times compared to a sample without additives. Thus, we showed the potential for soil stabilization through MICP using organic waste. [ABSTRACT FROM AUTHOR]

Less than 65% of wastepaper can be recycled, and the remaining wastepaper may end up polluting groundwater and generating greenhouse gas emissions if disposed improperly by using traditional approaches. The concept of circular supply chain practices, which integrates circular thinking into supply chain practices that aim to reach zero waste by exploring novel business models and supply chain functions, has been proposed to address this issue. However, previous studies implementing this concept lacked appropriate methods for structuring an influential model to guide resource allocation, which caused difficulty in developing circular supply chain practices. Thus, a hybrid method is proposed to integrate factor analysis with fuzzy synthetic and decision-making and trial evaluation laboratory methods to enable visual analysis and boost understanding. The results reveal that awareness and engagement are the most influential factors in attempts to achieve zero waste, rather than the recycling, reuse and reduction practices emphasised by previous studies. [ABSTRACT FROM AUTHOR]

Many stray animals throughout the world unfortunately do not get the opportunity to find the loving home that they deserve. In this classification task, we look to develop an algorithm to predict the speed of pet adoptions. The input to our algorithm includes animal type (dog or cat), breed, gender, colour, profile picture online and the descriptions about the pet, etc. We then use both traditional machine learning techniques (Logistic Regression, Naive Bayes, SVM, Decision Tree, Random Forest and Gradient Boosting) and neural networks (fully connected neural networks and long short-term memory Model) to predict the adoption rate. In particular, we build feature vectors using information extracted from description scripts and feed them into neural network models. We are hoping to examine the results to develop strategies to help improve the overall adoption rate (i.e. what features lead to faster adoption). Every year, 3.3 million canines visit animal shelters, out of a total population of 200 million. Only 2% to 17% of pets are returned to their owners. The remaining animals are euthanized due to a shortage of room in shelters (killed). The present procedures for adapting or finding a pet are inefficient and haphazard. People disseminated leaflets to the general public and spread the word to others in the vicinity of the pet's disappearance. When individuals print fliers, they waste paper and money since there is no good impact. People also share their tales on social media sites like Instagram and Facebook. There are also several fraudsters who attempt to fraudulently claim the incentive for returning the pet to its legitimate owner. We want to provide an analysis on how fast pets(cats and dogs) can be adopted based on various factors like their health conditions, age, colour, breed etc. [ABSTRACT FROM AUTHOR]

Many substances looks black often means that these substance can completely absorb ultraviolet radiation and Visible incident light (UV). Ultraviolet and visible light account for 57 % of the incident energy of the sun. There are many substances that looks black, but have not been paid attention in the field of photothermal interface evaporation. Based on the above discussion, this paper selects the waste black round plastic lunch box and a piece of black garbage bag as solar photothermal materials to make a solar desalination device, and proves that these black garbage can be recycled and reused to make an interface solar evaporator. In this paper, a 2D desalination device with photothermal interface evaporation for solar thermal conversion was successfully fabricated using only black round plastic lunch box as photothermal material and polyester cloth as water delivery channel. In addition, a black garbage plastic bag as the only solar photothermal conversion material has also been reused in the preparation of 3D evaporators. Using the radiation cooling film as the diffuse reflection substrate, the 3D device makes the incident sunlight reflected from the radiation cooling film and polyester cloth to the black garbage plastic bag many times, making the whole evaporation device. It can reabsorb solar incident light many times. After testing, the solar energy absorption rate of the 3D evaporator is as high as 96.6 %, and the steam output is as high as 8.96 kg m−2 h−1. • A number of matters that appears black are not been concerned in the field photothermal evaporation。 • Black round plastic lunch box and a piece of black garbage bag are recycled as solar absorber. • These black kitchen wastes are confirmed that can be recycled and re-used • By taking advantage of radiative cooling film, solar energy can be muti-reflected and muti-reabsorbed • The high solar absorbance of 96.6 % and steam output of 8.96 kg m−2 h−1 can be achieved [ABSTRACT FROM AUTHOR]

The reuse of waste papers by conversion into valuable carbon materials has received considerable attention for diverse applications such as energy storage and water purification. However, traditional methods for converting waste papers into materials with suitable properties for specific applications are often complex and ineffective, involving consecutive carbonization and activation steps. Herein, we propose a simple one-step microwave (MW)-assisted synthesis for preparing waste paper-derived porous carbons (WPCs) for energy storage and water purification. Through a 30-min synthesis, WPCs with graphitic structure and high specific surface area were successfully produced. The fabricated WPCs exhibited outstanding charge storage capability with a maximum specific capacitance of 237.7 F g−1. Additionally, the WPC demonstrates a high removal efficiency for various dyes, achieving a maximum removal efficiency of 95.0% for methylene blue. The developed one-step MW synthesis not only enables the production of porous carbon from waste paper, but also offers a viable approach to address solid waste management challenges while simultaneously yielding valuable materials. [Display omitted] • Waste paper-derived porous carbons were synthesized by one-step microwave synthesis. • Within 30-min MW synthesis, graphitic and high-surface area WPCs were produced. • WPC exhibits outstanding electrochemical capacitance of 237.7 F g−1. • WPC exhibits high removal of various dyes, with maximum of 95.0% for methylene blue. [ABSTRACT FROM AUTHOR]

Chemical Looping Combustion (CLC) is a carbon capture technology that uses an oxygen carrier to transfer the oxidizing agent to the fuel for combustion. This study used different machine learning algorithms, Artificial neural network and Response surface methodology to estimate the surface region process performance and optimize the process condition for the CLC of different solid fuels waste paper, plastic waste, and sugarcane bagasse blends. Based on the combustion efficiency, CO 2 yield and CO 2 capture efficiency responses, A high performance correlation (R2 > 0.8) was obtained for all the combustion parameters analyzed. The perturbation plot derived from the RSM analysis indicated that the most significant input parameters include the steam to fixed carbon, blend ratio and the fuel reaction temperature. The CLC process was optimized using RSM. For blends of SCB/WP, the best operating conditions were found to be 800 °C, a solid flow rate of 197.7 kg/h, an oxygen carrier to fuel ratio of 1.1, a steam to fixed carbon ratio of 2.16, and a blend ratio of 1. Similarly, for blends of SCB/PW, the optimal operating conditions were 800 °C, a solid flow rate of 199.4 kg/h, an oxygen carrier to fuel ratio of 1.3, steam to fixed carbon ratio of 2, and a blend ratio of 0.3. The optimum combustion performance was found to be 0.98, 0.78, and 0.96 for SCB/WP and 0.99, 0.62, and 0.96 for SCB/PW, respectively. • The process performance of the CLC of MSW/biomass blend was compared using ANN and RSM. • The optimal blend ratios for SCB/WP and SCB/PW blends were 1 (25% WP) and 0.3 (42.5% PW). • The combustion performance of the WP improved by 6.2% and 3.5% in terms of combustion efficiency and CO 2 yield, respectively. • The most significant input factors were discovered to be the blend of fuels ratio and the steam to fixed carbon ratio. [ABSTRACT FROM AUTHOR]

[Display omitted] • The alcohol yields achieved were 41.3 wt% and 48.5 wt% from the corrugated box and A4 paper. • Cellulose exhibited the conversion rate of 100 %, with alcohol substances achieving a yield of 71.2 wt% and a selectivity of 89.4 % within 6 h. • The mechanism of cellulose hydrolysis and the catalytic effect of CuMgAlO x were explored. • Multiple techniques were utilized to analyze the alcoholysis pathways and mechanisms of cellulose in waste paper. In an effort to valorize under-exploited cellulose sources like waste paper for sustainable energy production, this study investigates a catalytic process to convert these materials into low-carbon alcohols. We explored the conversion efficiency of various cellulose materials, including corrugated box, A4 paper, and pure cellulose, under the influence of a CuMgAlO x catalyst. Our findings indicate that at 360 °C for 6 h, the conversion rates were substantial, yielding 70.1 % for corrugated box, 85.2 % for A4 paper, and 100 % for cellulose. The respective alcohol selectivities achieved were 54.7 %, 83.0 %, and 89.4 %, with alcohol yields of 41.3 wt%, 48.5 wt%, and 71.2 wt%. Notably, the absence of the catalyst led predominantly to the production of sugars and lipids, whereas the catalytic conditions facilitated the formation of alcohols. The study also examined the effects of temperature and reaction time on cellulose conversion. It was found that a complete conversion was possible at 320 °C within 1 h, with extended temperature and time improving the alcohol yield. The development of a kinetic model for the cellulose conversion process has allowed for accurate predictions of the transformations under varied conditions, which offers a strategic framework for reaction optimization. Furthermore, the role of the CuMgAlO x catalyst was elucidated through the examination of model compounds, demonstrating its capability in converting cellulose intermediates such as sugars, lipids, and ketones into alcohols. This research highlights a potent strategy for the production of high-value, eco-friendly green fuels from readily available paper products and cellulose biomass, marking a significant advancement in chemical engineering and sustainable energy resources. [ABSTRACT FROM AUTHOR]

Collection, as the first stage of the recycling process, and pre-processing to increase waste stream purity constitute key operations for achieving high recycling rates and a closed loop in the circular economy. For wastepaper recycling in Hong Kong, it is the semi-formal-informal recycling (SFIR) sector that plays a central role in both stages. This study analyses the so far little explored SFIR stakeholder network in Hong Kong and sheds light on value chains, recovered waste paper quantities and the impact of policies on the sector. The findings show that SFIR stakeholders reclaim 55.6 t/recycling station/month of wastepaper and thereby achieve about a 5.7 times higher reclaim rate than the formal-private recycling system. Critical to this achievement is the SFIR transaction network, which enables its stakeholders to develop a value chain and thereby generate an added value of around 1900 HKD (243.9 USD/t) for wastepaper. Given limited circular structures in Hong Kong, financial subsidies are critical to sustain the SFIR's operations over the short-term. However, over the long-term legalization and integration of its stakeholders are necessary to ensure an economically and socially sustainable wastepaper recovery system in Hong Kong. [Display omitted] • Qualitative & quantitative analysis of the semi-formal-informal recycling (SFIR) sector. • The SFIR's wastepaper value chain achieves a cumulative added value of 1900 HKD/t. • The SFIR recovered 5.7 times higher capacities than the formal system in 2021. • Financial support can enhance the SFIR sector's recovery capacities. [ABSTRACT FROM AUTHOR]

The Ecological Footprint (EF) model is an effective tool for determining the resource consumption demand of human activities and whether natural assets are overutilized. The EF calculation method has certain theoretical and methodological importance for low-carbon campus construction. With the development of science and technology, some parameters in traditional EF calculation methods need to be modified. Based on the definition of fossil energy land and the latest average grain yield, this paper revised the calculation parameters of the EF method in six aspects: absorbed gas, electricity, agricultural products, aquatic products, livestock products, and paper. This paper applied the calculation method before and after improvement to Henan Polytechnic University. The EF of the campus according to calculations was 28,358.41 gha, and the per capita EF was 0.657 gha/person using the improved calculation method. Compared with the unimproved method, the improved method resulted in a substantial decrease in EFs, which can be explained by three reasons. First, the fossil energy land was divided into forestland and pasture land. Second, the average yield was recalculated using the latest statistical database of the United Nations Food and Agriculture Organization. Finally, the utilization of waste pulp in the paper industry was considered. The calculated results were also analyzed and compared with those of other universities, Worldwide Fund for Nature and Enhancing Universities'Sustainability Teaching and Practices through Ecological Footprint. The improved calculation results can better reflect the actual situation of the campus, improve the rationality of EF calculation, and provide a reference for EF at the campus level. Accordingly, the current situation of campus resource consumption can be explained, further providing a basis for proposing an EF reduction scheme for green campus construction. [Display omitted] • Some parameters have been modified in the improved ecological footprint calculation method. • The fossil energy land was divided into forestland and pasture land in the improved calculation method. • The latest average grain yield used in the improved calculation method. • The calculated results were analyzed and compared with those of WWF and EUSTEPs. [ABSTRACT FROM AUTHOR]