Search

Due to a shortage of resources, exploring new biomass fillers has become critical for paper making. In this study, we reported an eco-friendly strategy for fabricating low-cost and efficient recycled paper with high mechanical properties using corrugated cardboard waste paper and harmless municipal sludge (HMS). First, the characteristics of HMS, including the particle size, pH, specific surface area, organic functional groups and organic component content, were analyzed. Then, the influence of the amount of HMS on the properties of the recycled paper was studied. Finally, the strengthening mechanism of biomass filling recycled paper was discussed. The results showed that HMS, a biomass filler for recycled paper preparation, exhibited excellent physical and chemical properties, with a median particle size of 6.395 μm, a surface area of 39.974 m2 g−1 and organic functional groups. The tensile index of the recycled paper with 30 % HMS was 13.10 Nm/g, which was 16.4 % greater than that of the unfilled paper and showed better thermal stability. This excellent performance could be attributed to the uniform distribution of HMS on the fiber surface, which improved the accessibility of hydrogen bond formation between fibers. Thus, this study proved that HMS was an excellent biomass filler for producing recycled paper. [ABSTRACT FROM AUTHOR]

The effect of shredded waste office paper was considered when producing one-layered particleboard. Five different mixing ratios of shredded waste office paper/wood particles were used (0/100, 25/75, 50/50, 75/25, and 100/0) and two amounts of urea formaldehyde (UF) resin (10% and 15%). The boards were tested for their physical and mechanical properties, including modulus of elasticity (MOE), bending strength (MOR), and internal bond (IB) strength, in accordance with the European Norm (EN) standards. All properties of the boards were found to be improved via increasing the resin content. The 15% UF-bonded board with 100% wood particles had the highest MOR, whereas the board containing 100% wastepaper for 15% UF had the highest MOE. However, there was no statistical difference between the board types. Although increasing wastepaper content in the board negatively affected the IB, the usage of wastepaper up to 25% was shown to be acceptable as a raw material in the production of particleboard. None of the prepared boards met the EN 312 (1999) requirements for thickness swelling. The boards made from shredded waste office paper were more suitable for dry and indoor use. [ABSTRACT FROM AUTHOR]

The primary aim of this research was to explore the feasibility of producing environmentally friendly composite materials by employing diverse hybrid matrices consisting of dammar natural resin, supplemented with small proportions of two synthetic resins: one epoxy and the other acrylic. A blend of paper and chicken feathers served as the reinforcing elements. The fabrication of these composite materials utilized a hand layup technique. Targeted for applications in the furniture industry or interior design, their mechanical properties were assessed through various tests. Specimens were obtained from the manufactured samples and subjected to evaluations for tensile strength, compression, flexure, vibrations, Shore hardness, and water absorption. Results indicated that irrespective of the testing method employed, the mechanical strength properties exhibited a decline with an increase in the percentage of dammar in the hybrid resins, whereas the elasticity properties demonstrated an increase with this percentage.

Hemp hurd fiber, a low-value waste stream from the hemp industry, has potential downstream applications as an alternative to non-renewable plastics for single-use food service ware and packaging applications. Packaging paper substrates made from chemically pulped hemp hurd, mixed in varying ratios with bleached thermomechanical radiata pine pulp were developed and tested. Handsheets were characterized using several mechanical property tests including tensile strength, tearing resistance, burst strength, short-span compression, ring crush, together with Gurley air resistance, contact angle, and Cobb60 tests. Generally, addition of hemp hurd fibers significantly improved handsheet mechanical properties. Hot-pressing of the handsheets so as to approximate molded fiber thermoforming further enhanced their performance, with pure hemp hurd handsheets having the highest mechanical properties and barrier performance. A prototype was successfully thermoformed from hemp fiber, demonstrating overall feasibility of this fibre source for molded fibre objects.

This research provides an in-depth assessment of two paper yarn variants, examining their structural, functional, and performance characteristics. These yarns demonstrated favorable properties, including suitable linear density, twist, typical cellulosic functional groups as confirmed by Infrared spectroscopy, minimal hairiness, moisture transfer, and creditable mechanical strength. These yarns have flat layered cross-sections and grooved longitudinal surfaces. In addition, a low hairiness index (1.3–1.33) further acknowledged their smooth surface. Their remarkable evenness (15.86% and 7.08%) supported their effective wicking properties. Despite average breaking strength (0.77 cN/dTex and 1.05 cN/dTex) and moderate elongation, these yarns exhibited exceptional water-washing resistance and retained over 89% breaking strength after 15 washes. This study ranks these paper yarns as highly suitable for durable clothing fabrics, providing promising sustainable alternatives in the textile industry.

The effect of shredded waste office paper was considered when producing one-layered particleboard. Five different mixing ratios of shredded waste office paper/wood particles were used (0/100, 25/75, 50/50, 75/25, and 100/0) and two amounts of urea formaldehyde (UF) resin (10% and 15%). The boards were tested for their physical and mechanical properties, including modulus of elasticity (MOE), bending strength (MOR), and internal bond (IB) strength, in accordance with the European Norm (EN) standards. All properties of the boards were found to be improved via increasing the resin content. The 15% UF-bonded board with 100% wood particles had the highest MOR, whereas the board containing 100% wastepaper for 15% UF had the highest MOE. However, there was no statistical difference between the board types. Although increasing wastepaper content in the board negatively affected the IB, the usage of wastepaper up to 25% was shown to be acceptable as a raw material in the production of particleboard. None of the prepared boards met the EN 312 (1999) requirements for thickness swelling. The boards made from shredded waste office paper were more suitable for dry and indoor use.

The mechanical properties for paper sheets composited with glucose (Glc), methyl cellulose (MC), and carboxymethyl cellulose (CMC) were investigated. The paper composites were prepared by immersing paper sheets in aqueous solutions of these materials and drying at 100 °C for 30 min. The stress–strain curves for these paper composites were measured by a uniaxial tensile apparatus with a stretching speed of 2 mm/min. The breaking stress and strain for untreated paper were 24 MPa and 0.016, respectively. The paper composites demonstrated stress–strain curves similar to the untreated paper; however, the breaking point largely differed for these composites. The breaking strain and breaking stress for the Glc composite slightly decreased and those for the MC composite gradually increased with the concentration of materials composited. Significant increases in the mechanical properties were observed for the CMC composite. The breaking stress, breaking strain, and breaking energy for the 3 wt.% CMC composite were 2.0-, 3.9-, and 8.0-fold higher than those for untreated paper, respectively. SEM photographs indicated that the CMC penetrated into the inner part of the paper. These results strongly suggest that the mechanical improvement for CMC composites can be understood as an enhancement of the bond strength between the paper fibrils by CMC, which acts as a bonding agent. It was also revealed that the breaking strain, breaking stress, and breaking energy for the CMC composites were at maximum at the first cycle and decreased gradually as the immersion cycles increased. [ABSTRACT FROM AUTHOR]

The materials to produce concrete blocks (sand, gravel, and cement) are limited resources that are becoming scarce over time due to their increasing demand in construction. On the other hand, the waste of glass and paper is progressively increasing without being fully utilized through recycling. Therefore, the objective of this scientific research is to evaluate the influence on the mechanical properties of masonry concrete blocks made with recycled glass and paper particles. Likewise, the sample was non-probabilistically selected for convenience, consisting of 192 concrete blocks manufactured with additions of 3% (2% glass particles and 1% recycled paper), 6% (4% glass particles and 2% recycled paper), and 9% (6% glass particles and 3% recycled paper), as well as concrete blocks manufactured without additions. According to the results obtained, at 3%, 6%, and 9% addition of glass and paper particles, the absorption decreased by 4.94%, 3.398%, and 3.52% respectively. However, the warping increased between 1.7mm and 1.8mm, while the compressive strength (f'c) increased to 75kg/cm2, 82kg/cm2, and 77kg/cm2, respectively. Similarly, the axial compressive strength (f'm) increased to 91.22kg/cm2, 94.45kg/cm2, and 92.80kg/cm2, and the diagonal compressive strength (V'm) increased by 8.90kg/cm2, 9.70kg/cm2, and 9.70kg/cm2. Nevertheless, the manufacturing cost of masonry units showed a progressive reduction with the amount of glass + paper addition, amounting to 0.57 USD, 0.55 USD, and 0.53 USD. It was also determined that the optimal addition of these materials in the concrete mix in terms of cost and strength is 9% (glass + paper), resulting in compressive strengths of 77kg/cm2, 92.8kg/cm2, and 9.70kg/cm2, with a cost of 0.53 USD per unit. In conclusion, it can be affirmed that adding glass and recycled paper particles in the production of concrete blocks for use in loadbearing masonry walls positively influences the physical and mechanical properties of the blocks. Additionally, it allows for a reduction in manufacturing costs, leading to significant savings for builders. [ABSTRACT FROM AUTHOR]

The influences of nano-chitosan and cationic polyacrylamide (cPAM) on the optical and mechanical properties of paper made from chemi-mechanical pulp (CMP) were investigated. Bleached chemi-mechanical pulp (CMP) was selected as the control sample. The cPAM was considered at four levels (0%, 0.25%, 0.5%, and 0.75%), while chitosan was added to the CMP suspension at three levels (0%, 1%, and 2%). Paper test specimens were prepared according to TAPPI standards with a basis weight of 60 g/m2, and their optical and mechanical properties were measured. The results indicated that the opacity, greenness, tear strength, burst strength, and Gurley seconds were increased, whereas brightness, water absorption, and a* factor were decreased by increasing the amount of cPAM. Adding chitosan to CMP increased the a* factor, tear strength, breaking length, burst strength, Gurley seconds, water absorption, and greenness in the resulting paper. When polyacrylamide and nano-chitosan were added simultaneously to CMP, the brightness, water absorption, and greenness of the resulting paper decreased, but opacity, burst strength, tear strength, and air resistance had an appropriate increase. In all treatments, the best results were found at 1% chitosan and 0.5% cPAM due to favorable optical and mechanical properties.

Xuan paper is one of the most famous handmade papers in China and is an important paper for conservation. However, the evenness of Xuan paper has not yet received much attention. In this study, the distribution of the in-plane grammage and mechanical properties of Xuan paper are measured. It is found that the distribution of the in-plane grammage and mechanical properties of Xuan paper is uneven. In the handmade direction, the grammage and mechanical properties of Xuan paper are overall largest in the lower area, followed by the upper and middle areas. The sheet forming process of Xuan paper has an important effect on the distribution of in-plane grammage, mechanical properties, and fiber orientation of Xuan paper. The folded state has a negative effect on the mechanical properties of the folded area of Xuan paper. This study will help raise awareness of the unevenness in physical properties of Xuan paper, which is important in both conservation and research applications. [ABSTRACT FROM AUTHOR]

This study aims to comprehensively examine the influence of three distinct additives, namely carboxymethyl cellulose (CMC), hydroxypropyl methylcellulose (HPMC), and cellulose nanofibers (CNF), on the performance enhancement of corrugated base paper. For this purpose, steam‐exploded rice straw was treated with varying concentrations (2, 4, 6, 8, and 10 wt%) of CMC, HPMC and CNF. Analysis of the rice straw pre and post expansion, as well as the modified corrugated base paper, was conducted using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TG), tensile performance testing, and scanning electron microscopy (SEM). Results indicated that adding CMC, CNF, and HPMC to corrugated base paper significantly improved bonding between paper layers, particularly at 2 %, 6 %, and 8 % concentrations, respectively. This enhancement notably increased tensile strength and elastic modulus of the corrugated base paper. Tensile performance saw increases of 57.76 %, 59.01 %, and 60.25 %, while elastic modulus showed increments of 52.7 %, 9.4 %, and 136.69 %, respectively. These findings provide valuable insights for the preparation of corrugated base paper and highlight the potential of CMC, HPMC, and CNF in enhancing paper mechanical properties. [ABSTRACT FROM AUTHOR]

The primary aim of this research was to explore the feasibility of producing environmentally friendly composite materials by employing diverse hybrid matrices consisting of dammar natural resin, supplemented with small proportions of two synthetic resins: one epoxy and the other acrylic. A blend of paper and chicken feathers served as the reinforcing elements. The fabrication of these composite materials utilized a hand layup technique. Targeted for applications in the furniture industry or interior design, their mechanical properties were assessed through various tests. Specimens were obtained from the manufactured samples and subjected to evaluations for tensile strength, compression, flexure, vibrations, Shore hardness, and water absorption. Results indicated that irrespective of the testing method employed, the mechanical strength properties exhibited a decline with an increase in the percentage of dammar in the hybrid resins, whereas the elasticity properties demonstrated an increase with this percentage. [ABSTRACT FROM AUTHOR]

Expansive soil exhibits significant swellings and shrinkages, which may result in severe damage or the collapse of structures built upon it. Calcium-based admixtures, such as lime, are commonly used to improve this problematic soil. However, traditional chemical additions can increase significant environmental stress. This paper proposes a sustainable solution, namely, the use of lignin fiber (LF) from the paper industry to partially replace lime as an amendment for expansive soils. Both the macroscopic and microscopic characteristics of the lignin fiber-treated expansive soil are extensively studied. The results show that the mechanical properties of expansive soil are improved by using lignin fiber alone. Under the condition of an optimal dosage of 8%, the compressive strength of lignin fiber-modified soil can reach 193 kPa, the shear strength is increased by 40% compared with the untreated soil, and the water conductivity is also improved with the increase in dosage. In addition, compared with 2% lime-modified soil, the compressive strength of 8% lignin fiber- and 2% lime composite-treated expansive soil increased by 50%, the cohesion increased by 12%, and the water conductivity decreased significantly. The microstructure analysis shows that at an 8% lignin fiber content, lignin fibers interweave into a network in the soil, which effectively enhances the strength and stability of the improved soil. Simultaneously, the fibers can form bridges across the adjacent micropores, leading to the merging of pores and transforming fine, dispersed micropores into larger, connected macropores. Lime promotes the flocculation of soil particles, forming larger aggregates and thus resulting in larger pores. The addition of fibers exerts an inhibitory effect on the flocculation reaction in the composite-improved soil. In conclusion, lignin fibers are an effective addition used to partially replace calcium admixture for the treatment of expansive soil, which provides a sustainable and environmentally friendly treatment scheme for reducing industrial waste. [ABSTRACT FROM AUTHOR]

Expansive soil exhibits significant swellings and shrinkages, which may result in severe damage or the collapse of structures built upon it. Calcium-based admixtures, such as lime, are commonly used to improve this problematic soil. However, traditional chemical additions can increase significant environmental stress. This paper proposes a sustainable solution, namely, the use of lignin fiber (LF) from the paper industry to partially replace lime as an amendment for expansive soils. Both the macroscopic and microscopic characteristics of the lignin fiber-treated expansive soil are extensively studied. The results show that the mechanical properties of expansive soil are improved by using lignin fiber alone. Under the condition of an optimal dosage of 8%, the compressive strength of lignin fiber-modified soil can reach 193 kPa, the shear strength is increased by 40% compared with the untreated soil, and the water conductivity is also improved with the increase in dosage. In addition, compared with 2% lime-modified soil, the compressive strength of 8% lignin fiber- and 2% lime composite-treated expansive soil increased by 50%, the cohesion increased by 12%, and the water conductivity decreased significantly. The microstructure analysis shows that at an 8% lignin fiber content, lignin fibers interweave into a network in the soil, which effectively enhances the strength and stability of the improved soil. Simultaneously, the fibers can form bridges across the adjacent micropores, leading to the merging of pores and transforming fine, dispersed micropores into larger, connected macropores. Lime promotes the flocculation of soil particles, forming larger aggregates and thus resulting in larger pores. The addition of fibers exerts an inhibitory effect on the flocculation reaction in the composite-improved soil. In conclusion, lignin fibers are an effective addition used to partially replace calcium admixture for the treatment of expansive soil, which provides a sustainable and environmentally friendly treatment scheme for reducing industrial waste.

In recent years, an increasing focus has been placed on the mitigation of carbon dioxide emissions, underscoring the significance of the sustainable energy-conservation industry as a prominent and consequential field of development. As an energy-intensive procedure within the papermaking sector, the process of pulp-fiber beating necessitates an imperative exploration of alternative approaches aimed at mitigating energy consumption. This study has synthesized renewable cationic cellulose nanoparticles (CCNPs) extracted from the parenchymal cells of maize stalk pith. The objective is to demonstrate their viability as a reinforcing additive for paper sheets, thereby reducing the reliance on conventional beating processes. The results showed that CCNPs were prone to augment the physical strength of bleached papers, compared with unbleached papers. The inclusion of 9% CCNPs led to a remarkable 163.5% and 140.0% increase in tear and tensile indexes for bleached Eucalyptus paper, respectively. Incorporating CCNPs into non-refined paper yields physical traits akin to wood pulp paper beaten over 40 °SR. The CCNP-strengthened handsheets exhibited superior tensile and tear index in comparison to commercial dry strength additives such as cationic starch (CS) and cationic polyacrylamide (CPAM). Additionally, at 80 μg/ml concentration, E-B-9 displayed significant bactericidal effectiveness, achieving an impressive 97% reduction in Escherichia coli. This notable outcome is attributed to the presence of quaternary ammonium salt moieties in the formulation. This investigation introduces a promising approach where in the utilization of CCNP as an innovative multifunctional agent for paper holds the potential to enhance paper performance and concurrently reduce production costs. [Display omitted] ● The agro-waste CCNP acted well as a paper multifunctional addictive. ● The CCNPs promoted physical strengths of the paper from non-refined wood pulps. ● 9% CCNP-added sheet has mechanical properties akin to that from the 40°SR paper. ● 80 μg/ml of the bleached hardwood showed 97% bactericidal efficacy against E. coli. ● The improvement of CCNPs applied to bleached pulps is superior to unbleached pulps. [ABSTRACT FROM AUTHOR]

Copyright of China Pulp & Paper is the property of China Pulp & Paper Magazines Publisher and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

High-performance aramid papers are ideal insulating materials in the electric industry, due to their superior mechanical strength and insulation capabilities. However, when subjected to prolonged high-voltage and high-power operations, these papers are prone to electrical damage, such as breakdown or corona aging. Unfortunately, most damaged aramid papers are viewed as mere waste, discarded through landfill or other unsustainable disposal methods. It is not only contrary to circular economy principles but also poses a significant environmental threat due to the potential for pollution. Herein, a closed-loop recycling strategy is proposed that efficiently and effectively reclaims electrically damaged meta-aramid papers. Using the DMAc/LiCl deprotonation system, waste aramid papers are completely decomposed into molecular chains, exposing carbon residues resulting from electrical breakdown. These carbon residues are removed through a step-by-step purification process. A reprotonation treatment is then applied to regenerate new meta-aramid papers by reforming the intermolecular hydrogen bonds. This approach not only fully restores the original honeycomb-like structure but also ensures the crystallization and hydrogen bond content, maintaining both electrical and mechanical properties at above 90 % of their original values. Notably, our recycling method is also compatible with aramid-based composites, achieving exceptional recycling efficiency. [Display omitted] • Electrically damaged meta-aramid paper can be recycled in a closed loop. • The DMAc/LiCl system completely dissolves waste aramid into PMIA molecular chains. • Carbon residues induced by electrical breakdown can be removed by purification. • The synergistic conservation of electrical and mechanical properties exceeds 90 %. • Closed loop recycling strategy is also viable for inorganic-aramid composite paper. [ABSTRACT FROM AUTHOR]

Copyright of China Pulp & Paper is the property of China Pulp & Paper Magazines Publisher and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of China Pulp & Paper is the property of China Pulp & Paper Magazines Publisher and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Acta Materiae Compositae Sinica is the property of Acta Materiea Compositae Sinica Editorial Department and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Cellulose is commonly acknowledged as a sustainable material owing to its abundance and renewability. However, the abundance of hydroxyl groups makes the paper material highly hydrophilic, and the hydrogen bonds between the fibers are easily broken by water, leading to the degradation of mechanical properties. This work details the fabrication of a composite paper comprising interwoven cellulose and polylactic acid (PLA) structures through hot‐pressing and PLA impregnation onto handwritten paper derived from conventional wood pulp fibers as the substrate. The investigation assessed how varying PLA concentrations influenced the overall characteristics of the composite paper, including its morphology, structure, mechanical properties, water absorption behavior, and water contact angle. Experimental results revealed that the composite paper fabricated through our approach exhibited an intertwined structure comprising both PLA and cellulose. With a tensile index reaching 33.24 kN·m/kg and a mere 31.1% loss in tensile index post‐water treatment, the mechanical properties of the composite paper were significantly enhanced due to the robust interfacial compatibility between cellulose and PLA, as well as the adhesive effect of PLA. Furthermore, the composite paper (CP) is easily processable and amenable to thermoforming into paper trays as required, indicative of its potential applications in the packaging industry. [ABSTRACT FROM AUTHOR]

In a proton exchange membrane fuel cell (FC), the gas diffusion layer (GDL) is identified as the component that is most affected by mechanical compression. In this article, a particular focus is provided on the methods to measure the three main electrical parameters—contact resistance, through‐plane resistance, and in‐plane resistance—of the GDL under compression. A nonlinear decrease of these resistances under compression is typically observed. In particular, an important decrease is observed from 0 to 2 MPa, then a lower one above 2 MPa. The smallest contact and in‐plane resistances are measured for the graphitized straight carbon papers analyzing GDL resistances under compression gives a first approach to explaining ohmic losses in FCs as a large part of these losses is related to the GDL. This review would be helpful for researchers in better understanding ohmic losses and establishing a database of main GDL electrical resistances and their variations according to several operating parameters. These data could be used in design models to optimize GDL properties. [ABSTRACT FROM AUTHOR]

In this work high strength and tough metal‐ceramic laminated composites are fabricated by spark plasma sintering (SPS) of Ti3Al(Si)C2 MAX‐phase filled preceramic papers (TAC) and ductile Nb foils. The sintering is carried out at 1250 °C and 50 MPa for 5–20 min. Various stacking techniques are used to obtain Nb/TAC laminated composites with different architectures. SPS results in the formation of reaction layer (RL) with a complex composition, which changes the thickness insignificantly with increasing sintering time. The possible formation mechanism of RL is discussed. The bending strength of Nb/TAC composites is decreased from 410 to 350 MPa when lowering the thickness of ceramic layer. The maximum fracture toughness of 10.2 MPa·m1/2 is achieved for the composite with similar individual layers thickness. The toughening is explained by complex fracture mechanisms associated with deflection and branching of cracks at interfaces, delamination, plastic deformation of Nb layers, multiple cracking and crack deflection in ceramic TAC layers. [ABSTRACT FROM AUTHOR]

Although styrene acrylate emulsions (SAE) have demonstrated promising applications as surface sizing agents for paper, their strengthening effect on pulp fibers in papermaking is not clear. In this study, bagasse fibers, an agricultural waste, were treated with SAE to study the influences on the mechanical properties of the produced papers. SAE copolymers with hard chain (H‐PSA) and soft chain (S‐PSA) were prepared and added to bagasse pulp slurry at concentrations of 1%–4% by weight. The findings indicated that for the soft and hard copolymers, the glass transition temperatures were 19.5 and 26.8°C and their emulsion particle sizes were 166 and 182 nm, respectively. The copolymers strengthened the produced paper by wrapping around and forming a network of chemical and physical bonds with the pulp fibers. Papers treated with 3% H‐PSA exhibited the optimum improvement in tensile strength (38 MPa) and breaking length (67 m) by 13% and 64%, respectively. Treated papers were negatively affected by UV radiation due to phenyl groups spread along the chains. The copolymers demonstrated good wet‐strength properties achieved by self‐ and co‐crosslinked networks. The prepared paper sheets showed a preference for the mechanical properties of treated samples over the untreated ones. [ABSTRACT FROM AUTHOR]

With the implementation of plastic restrictions and the increasingly serious problem of environmental pollution, paper with green and recyclable characteristics is gradually becoming a substitute for packaging materials. However, the rich cellulose structure in the paper, which contains hydroxyl groups leading to its hydrophilicity, allows water molecules to penetrate the paper and disrupt the hydrogen bonds between cellulose, resulting in a decrease in mechanical properties. Therefore, waterproof coatings are crucial for paper‐based materials to be used in many applications. Based on this, the paper surface was chemically modified with castor oil‐based resin (CO‐590) monomer prepared by coupling agent and castor oil (CO). The results indicated that the modified paper with the contact angle (CA) of 114° had excellent waterproof performance and had a reduction by 40.3% in water vapor transmission rate (WVTR), but also its mechanical increased to 26.9 MPa and the decomposition temperature to 410.5°C. In addition, the coating on its surface could be removed in an alkaline solution and had a possibility to recycle blank paper in the future for manufacturing sustainable production. This work not only provides a method for preparing modified packaging paper, but also expands the application fields of materials. [ABSTRACT FROM AUTHOR]

This study investigates the effect of 1,2,3,4‐butane tetracarboxylic acid (BTCA) crosslinking treatment on the electrical properties of poly‐p‐phenylene terephthalate (PPTA)/cellulose insulation paper to prepare a novel composite insulation paper with low dielectric constant and good electrical performance. Three‐layer PPTA/cellulose composite paper crosslinked by BTCA under various conditions, composite paper without crosslinking, directly mixed composite paper, and conventional Kraft paper are prepared. The morphology and surface chemical composition of the paper samples are characterized. Dielectric, mechanical, and thermal properties are investigated. Results show that the BTCA concentration of 0.2 mol L−1 with a 180°C curing temperature is the relatively superior crosslinking condition to prepare a novel composite with low dielectric constant and good comprehensive performance. The dielectric constant and loss of the novel composite paper decrease to 3.21 and 0.392 at 50 Hz. The tensile strength of the BTCA crosslinked three‐layer PPTA/cellulose composite paper (thickness: 130 μm) has reached 10.01 kN m−1, increased by 41.6% than the directly mixed composite paper. The novel BTCA crosslinked composite paper also shows improved thermal stability. The BTCA crosslinking proves to be a promising method to improve the dielectric properties and electrical performance of the PPTA/cellulose composite paper. [ABSTRACT FROM AUTHOR]

Copyright of China Pulp & Paper is the property of China Pulp & Paper Magazines Publisher and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Micro- and nano-hybrid cellulose fiber (MNCF) stands out as a versatile cellulosic nanomaterial with promising applications in various fields owing to its excellent intrinsic nature and outstanding characteristics. However, the inefficiency in preparing MNCF, attributed to a complex multi-step processing, hinders its widespread adoption. In this study, a straightforward and highly efficient method for MNCF preparation was developed via a hot water soaking-assisted colloid grinding strategy. Active water molecules in hot water facilitating stronger transverse shrinkage and longitudinal expansion in fiber crystallized region, and thus improving the fibrillation degree of cellulose fibers. As a result, MNCFs with a mean diameter of 37.5 ± 22.2 nm and high concentration (2 wt%) were successfully achieved though pure mechanical method. The micro and nano-hybrid structure leads to the corresponding resulting cellulose paper with micro- and nano-hybrid structure possesses a compact stacking and fewer defects, leading to extraordinary mechanical properties including tensile strength of 204.5 MPa, Young's modulus of 6.3 GPa and elongation of 10.1 %. This work achieves significant progress towards straightforward and highly efficient production of MNCFs, offering an appreciable prospect for the development of multifunctional MNCF-based materials. [ABSTRACT FROM AUTHOR]

Copyright of Transactions of China Pulp & Paper is the property of China Pulp & Paper Magazines Publisher and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)