Search

Abstract The energy consumption for cooling takes up 50% of all the consumed final energy in Europe, which still highly depends on the utilization of fossil fuels. Thus, it is required to propose and develop new technologies for cooling driven by renewable energy. Also, thermal energy storage is an emerging technology to relocate intermittent low-grade heat source, like solar thermal energy and industrial waste heat as well as to exploit off-peak electricity, for cooling applications. This review aims to summarize the recent advances in thermally driven cooling and cold storage technologies, focusing on the formation and fabrication of adopted composites materials, including sorption materials, phase change materials, and slurries. Herein, first the classifications, selection criteria, and properties for these three types of materials is discussed. Then, the application potentials of all the materials are prospected in terms of economic analysis and sustainability.

In this paper, cement mortar IN200 integrated with solid–solid PlusIce X25 commercial PCM was fully characterized for the first time via experimental tests and numerical simulations. An experimental setup was designed and built to evaluate the thermal performance of the composite. Experimental results confirmed the expected advantages of the PCM-loaded plaster in terms of inner surface temperature, inbound heat flux reduction, and the enhanced damping effect on the average temperature. The experimental results were used to validate and calibrate a finite element model implemented in COMSOL Multiphysics® 5.6. The model was adopted to carry out a parametric analysis assessing the influence of PCM mass fraction, phase transition temperature, and PCM mortar thickness. The composite thickness was the most influential parameter, resulting in an energy saving increase from 3.29% to 72.72% as it was increased from 10 mm to 30 mm. Moreover, the model was used in a set of dynamic simulations, reproducing real Mediterranean climatic conditions to capture the transition process for a long period in buildings. The PCM mortar located on the interior side exhibited the highest reduction in both heat flux and inner surface temperature, representing a simple approach to achieving the best thermal comfort conditions.

This study focuses on the development and testing under lab-controlled conditions of a hybrid sensible–latent thermal energy storage (TES) system for domestic hot water (DHW) provision in residential buildings. The TES system’s design is based, for the first time in the literature, on a commercial tank-in-tank architecture integrating a macro-encapsulated commercial phase change material (PCM) inside the external tank to guarantee the safe provision of DHW and increase overall energy storage density at a reasonable cost. The PCM is a salt hydrate with a nominal melting temperature of 58 °C. The overall tank-in-tank TES volume is about 540 dm3. Almost one tenth of this volume is occupied by the PCM macro-capsules. The developed TES system was comparatively tested against the same configuration operated as a sensible TES. The obtained results showed the ability of the PCM to increase the thermal inertia inside the external tank, thus guaranteeing the quite stable provision of heat to the integral DHW tank during the stand-by periods. This effect was confirmed by the PCM’s ability to achieve an energy storage capacity up to 16% higher than the reference sensible TES system.

Abstract The lack of robust and low-cost sorbent materials still represents a formidable technological barrier for long-term storage of (renewable) thermal energy and more generally for Adsorptive Heat Transformations—AHT. In this work, we introduce a novel approach for synthesizing cement-based composite sorbent materials. In fact, considering the number of available hygrosopic salts that can be accommodated into a cementitious matrix—whose morphological properties can be also fine-tuned—the new proposed in situ synthesis paves the way to the generation of an entire new class of possible sorbents for AHT. Here, solely focusing on magnesium sulfate in a class G cement matrix, we show preliminary morphological, mechanical and calorimetric characterization of sub-optimal material samples. Our analysis enables us to theoretically estimate one of the most important figures of merit for the considered applications, namely the energy density which was found to range within 0.088–0.2 GJ/m3 (for the best tested sample) under reasonable operating conditions for space heating applications and temperate climate. The above estimates are found to be lower than other composite materials in the literature. Nonetheless, although no special material optimization has been implemented, our samples already compare favourably with most of the known materials in terms of specific cost of stored energy. Finally, an interesting aspect is found in the ageing tests under water sorption-desorption cycling, where a negligible variation in the adsorption capability is demonstrated after over one-hundred cycles.

The objective of this research is to assess the operation of a heat pump (HP) under varying climatic conditions in Europe. To achieve this, a Dymola model is developed for a solar-assisted reversible water-to-water HP that utilizes a low global warming potential (GWP) refrigerant, R1234ze(E), and includes thermal and electrical energy storage systems. Experimental data is used to validate the primary components of the model. Simulations are conducted for both summer and winter seasons to determine the system’s overall annual performance. The analysis covers energy exchange between the system and the grid and utilizes key performance indicators such as self-sufficiency and self-consumption index. Furthermore, a techno-economic analysis is conducted to determine the payback period of the heating and cooling energy system based on the components’ capital expenditure and available incentives.