Search

Purpose: To compare the color dimensions, color discrepancies (E00), and surface roughness of milled materials before and after application of a bleaching agent. Materials and Methods: A total of 10 extracted molars were obtained. Each tooth was cut in transverse sections to create disks (3-mm thick, 10-mm diameter; control group). Disk specimens of eight materials (n = 10 per group) were fabricated: polymethyl methacrylate (PMMA) interim material (PMMA-Telio group), two resin nanoceramics (RNC-Ultimate group and RNC-Cerasmart group), two hybrid ceramics (HC-Shofu group and HC-Enamic group), lithium disilicate (LD-Emax group), zirconia-reinforced glass ceramic (ZGC-Suprinity group), and zirconia (Zr-InCeram group). Color measurements were obtained using a spectrophotometer before and after applying 35% hydrogen peroxide-based bleaching agent. Pre- and postbleaching surface roughness (Sa) analyses were completed using a profilometer. Results: Significant L*, a*, b*, and E00 value differences were found (P < .05). Color discrepancies (E00) ranged from 0.30 ± 0.14 to 4.82 ± 0.10. The highest color discrepancies were measured on the PMMA-Telio group, while the lowest color discrepancies were computed for ZGC-Suprinity, RNCUltimate, and RNC-Cerasmart. Significant surface roughness differences were found (P < .05). The largest increase of surface roughness values between the pre- and postbleaching measurements was obtained in the PMMA-Telio group with a mean Sa value of 4.73 ± 3.02, while the largest decrease of surface roughness values between the pre- and postbleaching measurements was obtained in the Zr-InCeram group with a mean Sa value of -1.58 ± 0.10. Conclusions: The milled materials showed significant pre- and postbleaching color and surface roughness discrepancies. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the esthetic outcomes based on the color differences in zirconia (Zr) of varying thickness, resin cement color, and types of titanium (Ti) implant surface treatments. Materials and Methods: Overall, 28 high-translucency monolithic zirconia (HTMZ) specimens were arranged into four groups based on Zr thickness: 1.0, 1.5, 2.0, and 2.5 mm (n = 7 per thickness). Each group was tested using two resin cement colors (clear and opaque) in combination with six surface-treated Ti groups (n = 7), including untreated titanium (UT), anodization (AN), 50-µm alumina airborne-particle abrasion followed by AN (SBAN), AN followed by 50-µm alumina airborne-particle abrasion (ANSB), 9.5% hydrofluoric acid followed by AN (HFAN), and AN followed by 9.5% hydrofluoric acid (ANHF). This created a total of 48 experimental groups, including the use of composite resin (n = 7, shade A2D) for four control groups. All specimens were measured using a spectrophotometer and subsequently compared with composite resin (control) with the corresponding Zr thickness to establish color differences. A color difference of < 2.7 was considered clinically acceptable. The data obtained were statistically analyzed using ANOVA and post hoc test (P = .05). Results: Zr thickness, resin cement color, and type of Ti implant surface treatment significantly affected the observed color differences (P < .05). When using 2.5-mm HTMZ with clear resin cement on AN, UT, SBAN, HFAN, and ANSB, the mean color differences were below the clinically acceptable values, and the 95% CIs of color differences were below the clinically acceptable values for AN, UT, and SBAN groups. Conclusions: HTMZ with a minimum thickness of 2.5 mm and clear resin cement on AN, UT, and SBAN groups potentially result in acceptable color matching with 95% CIs. [ABSTRACT FROM AUTHOR]

Purpose: To investigate how well an implant stability quotient (ISQ) represents resonance frequency. Materials and Methods: Benchtop experiments on standardized samples that replicated a mandibular premolar site were conducted to correlate an ISQ value and a resonance frequency to synthetic bone density and an incremental insertion torque; then, a frequency spectrum analysis was performed to check the validity of the resonance frequency analysis (RFA). Brånemark Mk III implants (4 × 11.5 mm; Nobel Biocare) were placed in Sawbones test models of five different densities (40, 30, 40/20, 20, and 15 PCF). An incremental insertion torque was recorded during implant placement. To perform stability measurements, the test models were partially clamped in a vise (unclamped volume: 10 × 20 × 34 mm). A MulTipeg (Integration Diagnostics) was attached to the implants, and a Penguin (Integration Diagnostics) RFA measured ISQ. Simultaneously, the MulTipeg motion was monitored via a laser Doppler vibrometer and processed by a spectrum analyzer to obtain the resonance frequency. Tightness of the clamp was adjusted to vary the resonance frequency. A statistical analysis produced a linear correlation coefficient (R) among the measured ISQ, resonance frequency, and incremental insertion torque. Results: The resonance frequency had high correlation to the incremental insertion torque (R = 0.978), confirming the validity of using RFA for this study. Measured ISQ data were scattered and had low correlation to the resonance frequency (R = 0.214) and the incremental insertion torque (R = 0.386). The spectrum analysis revealed the simultaneous presence of multiple resonance frequencies. Conclusions: For the designed benchtop tests, resonance frequency does indicate implant stability in view of Sawbones density and incremental insertion torque. However, ISQ measurements do not correlate to the resonance frequency and may not reflect the stability when multiple resonance frequencies are present simultaneously. [ABSTRACT FROM AUTHOR]

Purpose: To evaluate the dimensional accuracy of implant impressions obtained using five different tray types and two techniques. Materials and Methods: A partially dentate maxillary Kennedy Class II model was created as a reference model through 3D printing. Then, implant analogs 4.3 mm in diameter were placed at the first premolar, first molar, and second molar sites. Five types of trays were used to create impressions: (1) metal stock trays, (2) plastic stock trays, (3) custom trays fabricated using liquid crystal display (LCD), (4) custom trays fabricated using fused deposition modeling (FDM), and (5) custom trays fabricated using urethane dimethacrylate (UDMA) resin. Open and closed tray techniques were also compared. In total, 150 impressions were obtained. The reference model and impressions were scanned using a laboratory scanner. Additionally, the positional and angular deviations of implants with different tray types and techniques were evaluated using the superimposition method. Results: There was no statistically significant difference (P > .05) between the impression accuracy with the different tray types and impression techniques. The angular deviations with plastic and UDMA trays were greater than those with metal, FDM, and LCD trays. Angular deviation at the second molar was greater when using closed plastic trays compared to open plastic trays. The highest and lowest positional deviations were observed at the first molar implant with an open plastic tray impression (mean ± SD of 62.46 ± 28.54 mm) and a closed LCD tray impression (36.59 ± 29.93 mm). The greatest angular deviation was observed with an open FDM tray impression at the first premolar implant (0.067 ± 0.024 degree), and the lowest angular deviation was observed with a closed metal stock tray impression at the second molar implant (0.039 ± 0.025 degree). Statistical differences were detected using the Mann-Whitney U test for paired groups and the Kruskal-Wallis test for groups with more than three comparisons (P > .05). Conclusions: Plastic and metal stock trays or conventional and 3D-printed custom trays can be used to obtain implant impressions for maxillary partially edentulous arches with similar dimensional accuracy. The five tray types and two techniques may be safely used to obtain impressions of partially edentulous maxillary arches with three implants. [ABSTRACT FROM AUTHOR]

The article discusses studies which show that full-ceramic prosthetic restorations for single crowns (SCs) and fixed dental prostheses (FDPs) are high quality and have a satisfactory survival rate comparable to porcelain-fused-to-metal (PFM). These studies include the survival outcome and complications in a retrospective clinical study of complete-arch fixed implant-supported prostheses (CAFIPs), the prevalence of prosthetic complications, and clinical performance of implant-supported FDPs.

Purpose: To compare the effect of taper, length, angle, and number of vertical axial walls on the retentive strength of a cemented crown on a partially customized hybrid abutment in the esthetic zone. Materials and Methods: A total of 35 metal copings were used and divided into two groups. One group had 30 copings cemented to their corresponding 8-degree tapered abutment with lengths from 3 to 8 mm, increasing in 1-mm increments (5 copings per length). The other group had the remaining 5 copings and consisted of a standardized metal coping that matched a hexagonal abutment with 3-mm vertical axial walls and the sequential removal of 1, 2, and 3 contiguous vertical axial walls. Dislodgment tests were performed for all copings in both groups. Maximum retentive forces were measured in retentive strength (kgF), with a conversion factor of 9.807 N = 1 kgF. Results: At each tapered abutment length, the retentive strength increased proportionally and was significantly different, ranging from 31.67 ± 4.10 kgF to 67.68 ± 11.22 kgF (F [5,24] = 20.46, P < .001). An unmodified hexagonal abutment demonstrated the highest retentive strength (70.15 ± 12.97 kgF). The sequential removal of 1, 2, and 3 contiguous vertical axial walls of the hexagonal abutment resulted in retentive strength values of 59.89 ± 10.06 kgF, 57.01 ± 9.62 kgF, and 55.99 ± 9.35 kgF, respectively, with no significant difference (P > .05) in strength. Conclusions: A partially customized abutment with vertical axial walls on one side and a profile reduction on the opposite side can provide comparable retention to cemented copings at one-third the length and at one-sixth the surface area of an 8-mm abutment with an 8-degree taper. [ABSTRACT FROM AUTHOR]

Purpose: To measure the surface temperature distribution after using a CO2 laser to heat titanium dental implants via different power settings, application intervals, and irradiation times. Materials and Methods: A total of 10 tissue-level titanium implants (Screw-Line Promote Plus, Camlog; 4.3 × 11 mm) were placed (EpoFix, Struers) and irradiated with a CO2 laser (Denta 2, Lutronic) with a wavelength of 10.6 µm at power levels of 4 watts (Group 1), 6 watts (Group 2), 8 watts (Group 3), and 10 watts (Group 4). A continuous beam mode (setting I) and noncontinuous beam modes with 5-second (setting II) and 10-second (setting III) pause intervals were used. For each setting, a total irradiation time of 50 seconds was used and repeated 10 times. The temperature was measured using external thermocouple (Testo) in contact with the implant surface at the implant shoulder, middle, and apex. A linear regression model was used to analyze the data (P = .05). Results: Setting I demonstrated the most rapid increase in implant surface temperature in all three test sites as well as the greatest total temperature at 50 seconds of irradiation time. The greater the pause interval (settings II and III) during the 50 seconds of irradiation, the lower the rate of temperature increase as well as the total temperature in all three test sites and with all power levels. The average temperature difference between the apex and shoulder site was significant for setting III for all groups, but not for any groups in settings I and II. Conclusions: Heating the internal aspect of an implant with a CO2 laser produces different temperature distribution profiles depending on the laser power level and the application interval. Laser-beam irradiation leads to a temperature gradient, which is greatest at the implant apex and smallest at the implant shoulder. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the screw loosening and fracture resistance of different hybrid abutment crown restorations after thermomechanical aging. Materials and Methods: Restorations were produced from zirconia, lithium disilicate, and hybrid ceramics with a CAD/CAM system (n = 10). Restorations and titanium bases (Ti-bases) were cemented, and the abutment screws were torqued to 30 Ncm. They were retorqued after 10 minutes, and then the removal torque values (RTVs) were measured. After 250,000 and 500,000 cycles of thermomechanical aging were completed, the RTVs were measured again, and removal torque loss (RTL) ratios were calculated. The specimens were subjected to a fracture resistance test after 750,000 cycles of thermomechanical aging, and the load at failure was recorded as the fracture resistance (N). The results were statistically analyzed (a = .05). Results: Aging was effective on the RTVs and RTL ratios (P < .001). The highest RTV was observed before aging; however, the RTVs significantly decreased and RTL ratios significantly increased after aging (P < .05). The fracture resistance values significantly differed among the ceramic materials. All lithium disilicate and hybrid ceramic specimens showed restoration fracture and most of the zirconia specimens showed Ti-base-related failure. Conclusions: Hybrid abutment crowns made of zirconia, lithium disilicate, and hybrid ceramics can withstand the average occlusal forces in the molar region; however, the ceramic type may affect the failure type. Retightening of the abutment screws after 10 minutes following the first tightening and annually may be beneficial to prevent the adverse effects of screw loosening on the integrity of the implant-abutment connection. [ABSTRACT FROM AUTHOR]

Surface contaminants on customized implant abutments could trigger an inflammatory response in the peri-implant tissues. The aim of this randomized controlled study was to assess the radiographic bone changes around implants restored with customized, platform-switched abutments, with and without autoclave treatment, 12 months after definitive restoration. Dental implants were placed 1 mm subcrestally in 64 systemically healthy patients (mean age: 63.3 ± 10.0 years; 31 patients had a history of periodontitis) to replace single or multiple missing teeth. According to a randomization list, abutments were subjected to steam and autoclave sterilization (43 implants, test group) or steam cleaning alone (44 implants, control group). Periapical standardized radiographs were taken at implant placement, prosthetic abutment connection, and 12 months after definitive cement-retained restoration. All implants were clinically stable without any sign of infection at the 12-month follow-up. An average marginal bone loss of 0.25 ± 0.19 mm was found in the test group compared to 0.35 ± 0.23 mm in the control group (no statistically significant difference), while the percentage of bleeding sites was significantly higher in the control group (8.7% ± 13.1% vs 19.1% ± 19.8%; P = .035). Autoclave treatment of customized abutments seems to reduce the inflammatory response around subcrestally placed implants. [ABSTRACT FROM AUTHOR]

Background: Platelet-rich fibrin (PRF) is used to prepare "sticky bone" by combining it with bone graft material. The present study investigated the ability of different bone grafts to absorb growth factors from the PRF and release them over time. Materials and Methods: Human blood was collected from 10 healthy volunteers for liquid PRF preparation. Bovine bone, allograft (mineralized and demineralized), and synthetic bone were each mixed with the PRF to prepare a sticky bone. All sticky bone samples were incubated for up to 4 days. The absorption and release pattern kinetics of two selective growth factors within the PRF--platelet-derived growth factor (PDGF) and bone morphogenetic protein-2 (BMP-2)--were quantified with immunofluorescence staining and enzyme-linked immunoassay (ELISA) testing. Results: All bone graft materials adsorbed the examined growth factors from the PRF. ß-TCP showed the highest adsorption levels, followed by the xenograft, and the allografts showed the lowest adsorption levels. Furthermore, PDGF showed a fast-release pattern from the grafts, whereas BMP-2 was released at a later stage. Similar to the adsorption pattern, the ß-TCP and xenograft were better able to sustain the release of the PRF growth factors from the graft than the allografts. Conclusions: The adsorption of PDGF and BMP-2 differ between graft materials, with superior results for ß-TCP, followed by xenograft, then allograft materials. [ABSTRACT FROM AUTHOR]

This clinical case outlines a comprehensive digital workflow for a minimally invasive multidisciplinary treatment. The process utilizes one open-source software for digital wax-up and one low-cost software to address esthetic concerns related to teeth misalignment. The patient's function was stabilized with a digitally made occlusal splint. The application of the described digital workflow technique, incorporating open-source, lowcost, and closed software, played a pivotal role in attaining a straightforward and predictable outcome with minimally invasive treatment. Furthermore, the continual evolution of technology contributes to the growing precision of dental procedures. The presented digital workflow helped formulate a predictable treatment plan, replicate a diagnostic digital wax-up, and achieve precise teeth alignment. This approach satisfactorily addressed the patient's esthetic concerns, providing an outstanding approximation of the definitive result. [ABSTRACT FROM AUTHOR]

Objectives: The objective was to evaluate the polymerization efficiency of different bulk-fill resin-based composites cured by monowave and polywave light-curing units, by assessment of the degree of conversion and Vickers microhardness at different depths. Method and materials: Two commercially available bulk-fill resin-based composites were used: Filtek One Bulk Fill Restorative (3M ESPE) and Tetric N-Ceram Bulk Fill (Ivoclar Vivadent). The light-curing units utilized were two LED light-curing units: a monowave LED light-curing unit (BlueLEX LD-105, Monitex) and a polywave LED light-curing unit (Twin Wave GT-2000, Monitex). For each test, 20 cylindrical specimens (4 mm diameter, 4 mm thickness) were prepared from each bulk-fill resin-based composite using a split Teflon mold. Ten specimens were light-cured by the monowave light-curing unit and the other ten were light-cured by the polywave light-curing unit according to the manufacturer's recommendations. Attenuated total reflectance-Fourier transform infrared spectroscopy (ATRFTIR) was used to assess the degree of conversion, and a Vickers microhardness tester was used to assess Vickers microhardness. Statistical analysis was performed using three-way ANOVA and Tukey post-hoc tests (P < .05). Results: The degree of conversion and Vickers microhardness in bulk-fill resin-based composites containing only camphorquinone as photoinitiator were similar when cured with either monowave or polywave light-curing units. However, bulk-fill resin-based composites containing a combination of photoinitiators exhibited significantly higher degree of conversion and Vickers microhardness when cured with a polywave light-curing unit. Although all groups showed statistically significant differences between the top and bottom surfaces regarding degree of conversion and Vickers microhardness, all of them showed bottom/top ratios > 80% regarding degree of conversion and Vickers microhardness. Conclusion: The polywave light-curing unit enhanced the polymerization efficiency of bulk-fill resin-based composites especially when the latter contained a combination of photoinitiators, but does not prevent the use of a monowave light-curing unit. [ABSTRACT FROM AUTHOR]

Purpose: To analyze the effectiveness of coating of abutments with antimicrobial agents and their influence on the physicochemical and biologic properties of the coated materials. Materials and Methods: This work was registered in Open Science Framework (osf.io/6tkcp) and followed the PRISMA protocols. A search of two independent reviewers of articles published up to October 29, 2021, was performed in the Embase, PubMed, Science Direct, and Scopus databases. Results: The databases found a total of 1,474 references. After excluding the duplicates, 1,050 remained. After reading the titles and abstracts and applying the inclusion criteria, 13 articles remained and were read in full. A total of 8 articles were included in this systematic review. Different antimicrobial agents have been used to coat abutments, including graphene oxide, polydopamine, titanium and zirconium nitride, lactoferrin, tetracycline, silver, and doxycycline with varied release times. Titanium-coated silver showed a better antimicrobial agent release time of up to 28 days. Chemical analysis confirmed the presence of antimicrobials on the surface after coating. Different pathogenic microorganisms, such as Streptococcus sanguinis, Streptococcus oralis, and Staphylococcus aureus, were inhibited when in contact with the coated surface. Conclusions: This review showed that there is still no consensus on which is the better antimicrobial agent and which coated materials have the better performance. However, the association of surface coating of abutments with antimicrobials is feasible and can benefit many patients, which can support their clinical use to favor the healing process and prevent infections that can lead to treatment failure with dental implants. [ABSTRACT FROM AUTHOR]

This canine in vivo study assessed the effect of recombinant human platelet-derived growth factor (rhPDGF) on the healing of periapical tissues following apical surgery. From a total of 96 premolar teeth, 64 teeth from six beagle dogs (2 years old) were classified as experimental and were randomly assigned to four experimental groups (16 teeth per group). After having the pulp extirpated, leaving teeth open to the oral cavity for 1 week, and sealing with an immediate restorative material for 8 weeks, nonsurgical endodontic treatment was performed. A split-mouth design was used, and intra-animal randomization of treatment sides was applied to the groups as follows: apical curettage + 1.5-mm root-end resection (Group 1); apicoectomy + mineral trioxide aggregate (MTA) root-end filling (Group 2); apicoectomy + MTA root-end filling + rhPDGF (Group 3); and apical curettage + rhPDGF (Group 4). The animals were sacrificed 24 months after apical surgery, and histologic and µCT analyses were performed for bone volume loss (BVL). Group 1 showed partial resolution of the periapical lesions without signs of tissue regeneration (BVL: 49.09 ± 10.97 mm3). Group 2 had minimal bone regeneration and showed cementum reformation in 9 teeth, with no direct attachment to the MTA (BVL: 35.34 ± 10.97 mm3). Group 3 showed regeneration of all damaged apical tissues without direct contact between the cementum and MTA (BLV: 4.51 ± 1.55 mm3). Group 4 showed regeneration of PDL, bone, and cementum and attachment of functional cementum fibers (BVL: 2.82 ± 2.3 mm3). The difference in BVL was statistically significant only for Groups 1 and 2 (P < .05). rhPDGF may help regenerate apical tissue structures following apical surgery. [ABSTRACT FROM AUTHOR]

This study aimed to evaluate the periodontal responses of subgingival proximal margins elevated using different restorative materials. A total of 120 proximal cavities with dentin/cementum gingival margins were elevated using one of four materials (resin-modified glass ionomer, glass hybrid, flowable bulk-fill resin composite, or bioactive ionic resin) and completed with the same overlaying resin composite. At 2 weeks (baseline), 6 months, 1 year, and 2 years postrestoration, periodontal parameters and the radiographic distance between the restoration margin and bone crest were evaluated. Appropriate statistical analyses were performed. The values of all periodontal parameters increased with time, although only the increases in Plaque Index and probing depth within each material group were statistically significant. There were no statistically significant differences in any of the periodontal parameters between the different materials within the same evaluation period, nor between different time points or material groups in the radiographic distances. Both glass ionomer--based and resin-based materials were periodontally safe as subgingival open sandwich restorations. [ABSTRACT FROM AUTHOR]

Objectives: To compare marginal gap width and depth with different cementation systems, excess removal, and after polishing. Method and materials: In total, 80 composite crowns were milled, divided into ten groups, and cemented on identical artificial teeth. Eight crowns per group were fixed with (i) zinc phosphate cement (ZnOPh), (ii) glass-ionomer cement (GIC), (iii) resin-reinforced glass-ionomer cement (GIC mod), (iv) dual-curing adhesive composite (Comp dual), or (v) dual-curing self-adhesive composite (Comp SE dual). Excess removal was performed with a scaler after brief light-cure (tack-cure), final light-cure, during rubber or gel phase or by wiping with foam pellet. Curing was completed in chemical, dark cure, or light-curing modus. The specimens were polished and stored in water (37°C). The margins were digitized using a 3D laser-scanning microscope (VK-X100 series, Keyence). The width and the depth of the marginal gap were measured at 10 points between the crown margin and the preparation margin. Results: The width after excess removal varied between 65.1 ± 15.7 µm (Comp dual, wipe, with polishing) and 208.6 ± 266.7 µm (Comp SE dual, dark cure, without polishing). The depth varied between 29.8 ± 22.2 µm (Comp dual, wipe, with polishing) and 89.5 ± 45.2 µm (Comp SE dual, dark cure, without polishing). The impact on gap width and depth was detected for fixation material, excess removal, and polishing. Conclusion: The gap depth and width depend on the luting material and the mode of access removal. Polishing can improve the gap quality, especially for GIC and resin-based systems. [ABSTRACT FROM AUTHOR]

Objectives: To evaluate the effect of sonic oscillation on penetration depth and marginal adaptation of resin-based fissure sealants. Method and materials: Thirty-six extracted human third molars were randomized into three groups: in the HF group, teeth were sealed with a filled-resin-based sealant (Helioseal F); in the Sonic-HF group, teeth were sealed with Helioseal F and subjected to sonic oscillation (Compothixo Device, 140 Hz vibration frequency and ± 150 µm amplitude) before curing; in the CO group, teeth were sealed with an unfilled-resin-based sealant (Clinpro). All teeth were thermocycled for 1,500 cycles at 5°C and 55°C, then sectioned buccolingually into four sections (mesial, two middle, and distal). Sections were evaluated under SEM for marginal adaptation and scored. For penetration depth, three independent measurements from each tooth were recorded under SEM, and data were subjected to statistical analysis. Results: The group subjected to sonic oscillation (Sonic HF) resulted in significantly superior penetration depth and marginal adaptation compared with the HF group, but with no significant difference compared with the CO group. Conclusions: Sonic activation of resin-based sealant increased penetration depth into fissures and marginal adaptation to the enamel wall without decreasing filler load or compromising sealant mechanical properties. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the effect of adhesive type and long-term aging on the shear bond strength (SBS) between silicabased ceramics and composite cement (CC). Materials and Methods: Lithium-silicate (LS), feldspathic (FD) and polymer-infiltrated ceramic (PIC) blocks were sectioned (10 x 12 x 2 mm) and divided into 24 groups considering the factors: "ceramics" (LS, FD, and PIC), "adhesive" (Ctrl: without adhesive; 2SC: 2-step conventional; 3SC: 3-step conventional; 1SU: 1-step universal), and "aging" (non-aged or aged [A]). After the surface treatments, CC cylinders (n = 15, ɸ=2mm; height = 2mm) were made and half of the samples were subjected to thermocycling (10,000) and stored in water at 37°C for 18months. The samples were submitted to SBS testing (100 kgf, 1mm/min) and failure analysis. Extra samples were prepared for microscopic analysis of the adhesive interface. SBS (MPa) data was analyzed by 3-way ANOVA and Tukey's test (5%). Weibull analysis was performed on the SBS data. Results: All factors and interactions were significant for SBS (p<0.05). Before aging, there was no significant difference between the tested groups and the respective control groups. After aging, the LS_1SU (22.18±7.74) and LS_2SC (17.32±5.86) groups exhibited significantly lower SBS than did the LS_Ctrl (30.30±6.11). Only the LS_1SU group showed a significant decrease in SBS after aging vs without aging. The LS_1SU (12.20) group showed the highest Weibull modulus, which was significantly higher than LS_2SC_A (2.82) and LS_1SU_A (3.15) groups. Conclusion: No type of adhesive applied after silane benefitted the long-term adhesion of silica-based ceramics to CC in comparison to the groups without adhesive. [ABSTRACT FROM AUTHOR]

Purpose: The study evaluated the clinical performance of partial indirect resin composite (PIRC) restorations with "proximal box elevation" (PBE) placed in molars. Materials and Methods: Sixty-three patients received 80 posterior PIRC (SR Nexco, Ivoclar Vivadent) restorations. Large posterior defects with cuspal loss and deep cervical margins were included in the study. PBE was performed priorto preparation and impression making. Two independent observers evaluated the restorations using the FDI criteria (scores 1-5) foresthetic, functional, and biological properties. Patients were recalled at 6 months and 1, 2, and 3 years. Overall success rates were calculated (Kaplan-Meier analysis) and compared (log-rank tests) according to baseline variables. The impact of the baseline variables on the failure of the restorations was analyzed (multiple proportional Cox regression). Results: Seventy-nine (98.7%), 69 (88.4%), 66 (92.9%), 44 (86.2%) and 45 (91.8%) PIRCs completed their follow up at baseline, 6 months, and 1, 2 and 3 years, respectively. In total, 10 failures were observed: 5 with partial loss, 4 with material chipping, and one with secondary caries, yielding an overall success rate of 87.5% and a survival rate of 93.8%, with a mean observation timeof 26.5 ± 13.6 months. Conclusions: PIRCs with PBE demonstrated a high survival rate and satisfactory esthetic properties. Failure was less likelyfor PIRC restorations with partial cuspal coverage (onlay) compared to full cuspal coverage (overlay). [ABSTRACT FROM AUTHOR]

Periodontal intrabony defects (IBDs) are commonly encountered in dental practice and are usually treated by open flap debridement (OFD) with or without bone grafts and/or guided tissue regeneration (GTR), platelet-rich fibrin (PRF), or other additives. A difficulty with these approaches is maintaining the space for bone growth at the determined location. In this report, autologous sticky bone (ASB) was used and compared to a simple mixture of PRF and bone graft (PRF-BG) using the identical graft material-bioactive glass morsels-to assess its regenerative potential in IBDs, as sticky bone is known to maintain the space, according to previous research. A total of 21 IBDs were treated by OFD, PRF-BG mixture, or ASB. Regenerative assessment was clinically and radiographically performed by CBCT at 1 year. All the treatment modalities (OFD, PRF-BG, and ASB) showed statistically significant improvements clinically and radiographically at 1 year in terms of probing pocket depth reduction (PPDR), clinical attachment level gain (CALG), CBCT defect fill (CBCT-DF), and CBCT defect resolution (CBCT-DR); P < .05. The ASB group depicted the most favorable results (P < .05) in terms of the parameters at 1 year followed by the PRF-BG group and then the OFD group. Treatment of periodontal IBDs with ASB resulted in significant improvements in clinical and CBCT parameters compared to baseline at 1 year, and intrasurgical graft handling was much better in the ASB group. [ABSTRACT FROM AUTHOR]

This study investigated the effect of erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser conditioning on dentin bond strength and nanoleakage of different universal and self-etch adhesives. A total of 84 intact human third molar teeth were cut at the dentin level, and half of them were laser conditioned. The specimens were divided into three groups; two different universal resins and one self-etch adhesive resin were applied and composite resin restorations were created. For the microtensile bond strength (pTBS) test, 20 microspecimens were prepared from the laser and control group of each adhesive (n = 20) and tested with a universal device. For nanoleakage observation, 10 specimens were prepared from each group (n = 10) and stored in silver nitrate solution, and then the amount of nanoleakage was analyzed by field emission scanning electron microscopy (FESEM). Data were analyzed with two-way ANOVA, Tukey's honestly significant difference, and chi-square tests. The mean dentin bond strength of all adhesives in the laser groups was found to be statistically significantly lower than those of the control groups (P < .05). No difference was found between the mean bond strength of the adhesives in the laser and control groups (P > .05). Higher nanoleakage was observed in all adhesives in the laser groups compared to the control groups (P < .05). Irradiation of the dentin surface with Er,Cr:YSGG could adversely affect the piTBS and nanoleakage, likely by affecting the structure of the hybrid layer. [ABSTRACT FROM AUTHOR]

Purpose: To evaluate the marginal leakage of three different types of bonding agents used with two posterior composites and a giomer, available commercially. Material and methods: Class II box-only cavities were prepared on 90 mandibular first molars with margins extending 1 mm beyond the cementoenamel junction. The samples were divided into nine groups based on three different bonding agents, two different composites, and a giomer. Cavities were restored per the manufacturer's description. Teeth were subjected to a thermocycling procedure (500Ã--, 5°C to 55°C) and dye penetration by immersing in a 2% methylene blue solution (Merck Specialties) for 24 hours. The marginal adaptation was evaluated as a continuous margin at the gingival level under a stereomicroscope. The results were analyzed using the Kruskal-Wallis and Mann-Whitney U tests. Results: The results of the groups with the total-etch technique showed no statistical difference between the nanohybrid Filtek Z250 XT (3M ESPE) and fine hybrid SwissTEC composite (Coltène\Whaledent AG). The groups with the self-etch technique showed no statistical difference when used with either of the two composites. The acid-etch technique showed better marginal adaptation than the self-etch technique. When the giomer (Beautifil II, Shofu) was used with the total-etch technique, it showed better adaptation than when used with the self-etch technique but overall showed more marginal leakage than the composites. Conclusion: The total-etch technique provided better marginal adaptation for the composites and giomer compared to the self-etch technique. Clinical significance: The demand for esthetic restorations continues to increase, and composite restorations are now considered the material of choice for Class II cavities. There are various concerns with composite restorations, one of them being good marginal adaptation to increase the life of the restoration. This study evaluated marginal leakage with the nanohybrid composite Filtek Z250 XT, fine hybrid composite SwissTEC, and a giomer when used with the total-etch technique and self-etch technique and reported satisfactory adaptation with the total-etch technique. [ABSTRACT FROM AUTHOR]

This article evaluated tooth discoloration after the use of calcium silicate-based materials to examine the effect of internal bleaching on tooth discoloration. The specimens were randomly divided into two experimental groups (n = 45) and a control group (n = 6). Cavities were filled with ProRoot MTA (Dentsply Sirona) in Group 1 and Biodentine (Septodont) in Group 2. Color measurements were taken with a spectrophotometer before and after the application of materials at 1 week, 13 weeks, and 6 months. After 6 months, Groups 1 and 2 were divided into three subgroups according to internal bleaching techniques. All color change ratios and lightness differences were calculated using the CIE L*a*b* system. Data were analyzed using repeated ANOVA and Kruskal-Wallis test (P = .05). There were statistically significant differences between Groups 1 and 2 at all time intervals (P < .05). Group 1 showed more discoloration than Group 2 (P < .05). There were no significant differences between the bleaching agents (P > .05). Additionally, specimens in both groups became lighter than their initial color (P < .05). Teeth treated with ProRoot MTA exhibited darkening at 1 week that increased over time, whereas those treated with Biodentine maintained the lightness for 6 months. [ABSTRACT FROM AUTHOR]

Purpose: To examine the stresses caused by different All-on-4 surgical techniques—conventional, a combination of monocortical and bicortical, bicortical, and nasal floor elevation—on the implant and the surrounding bone using 3D finite element analysis (FEA). Materials and Methods: A 3D bone model of the atrophic maxilla was created based on CT imaging of the fully edentulous adult patient. All implants used in the models were 4 mm in diameter, and the length was 13 mm in the anterior and 15 mm in the posterior. Implants were applied to four different atrophic maxillary models with the All-on-4 technique: anterior and posterior monocortical implants in the first model, anterior monocortical and posterior bicortical in the second model, anterior and posterior bicortical in the third model, and anterior and posterior bicortical with nasal floor elevation in the fourth model. Eight linear analyses were performed by applying force from both vertical and 45-degree oblique directions to the four models prepared in our study. Results: When the cortical and cancellous bone around the anterior implants was examined, it was observed that the oblique and vertical loading conditions and the stresses around the implant were similar in all models. When the posterior implants were examined, model 1 (ie, anterior and posterior monocortical implants) showed the greatest oblique compression, vertical compression, and vertical tension forces. According to the Von Mises stress (VMS) analysis results for anterior and posterior implants, higher values were observed in model 1 compared to models 3 and 4 under oblique and vertical forces. It was observed that bicortical placement of the implants reduced the stresses on the bone and implant-abutment system but had no significant effect on the stress on the bar. Conclusions: According to the results of our study, in the All-on-4 technique, bicortical placement of the implants reduced the stresses on the bone and implant when the anatomical limitations allowed. In addition, nasal floor elevation can be applied in the atrophic maxilla in appropriate indications. [ABSTRACT FROM AUTHOR]

The article discusses research published in the 2021 issue of the "International Journal of Environmental Research and Public Health" which evaluated the use of short dental implants compared to standard dental implants. The research reviewed studies on short implants and standard-length implants placed in augmented and nonaugmented edentulous sites, short implant survival, stability and marginal bone levels, and implants placed in the posterior maxilla and in medically compromised patients.

Fluorapatite glass-ceramic (GC) and yttria-stabilized zirconia (YSZ) are two commonly used ceramic materials for dental prosthetic restorations. Fluorapatite GCs are known for their outstanding biocompatibility and aesthetic characteristics, moreover, they can release fluoride ions which have anticaries effect. Nevertheless, they often lack the requisite strength and toughness to withstand high occlusal forces. Conversely, YSZ exhibits remarkable mechanical properties, however, it is susceptible to excessive wear on opposing teeth. To address these limitations, a novel fluorapatite GC-YSZ composite ceramic was designed and formed through vat photopolymerization. The effect of composition ratios of fluorapatite GC particles and YSZ fibers (0˗40 wt% YSZ) on the forming precision, mechanical properties, and tribological compatibility with GC was thoroughly investigated. The results demonstrated that optimal comprehensive performance was achieved when the YSZ fiber content reached 40 wt%, which resulted in a fracture toughness of 1.68 MPa m1/2, marking a 98.8 % increase over pure GC. The specific wear rates of the sample and the antagonistic titanium ball were reduced by 75.6 % and 63.8 %, respectively, compared with GC. In addition, the dimensional accuracy error of the green body was reduced by approximately 44 %. The design and fabrication of GC-YSZ composites offer an approach for developing high-performance all-ceramic dental materials. [ABSTRACT FROM AUTHOR]

Background: Using infection control barriers (ICBs) on light curing units (LCUs) became mandatory to achieve proper infection control measures without jeopardizing the integrity of the restorations, especially at deeper layers. This study explored the effect of two ICBs on the irradiance of the LCU, as well as the degree of conversion (DC) and flexural strength (FS) of two types of bulk-fill composites. Water vapor permeability (WVP) of both barriers was also assessed to evaluate the capability of such barriers to prevent transmission of blood and saliva droplets and aerosols. Methods: Two bulk-fill composites (X-tra fil and Tetric N- ceram) and two ICBs (Pinnacle Cure sleeve and Sanita wrapping film) were used in this study. Light irradiance was recorded per experimental condition using spectroradiometer. For DC and FS, specimens of 4 mm thickness were prepared. Each specimen was composed of two separable upper and lower layers of thickness 2 mm. DC and FS were measured using Infra-red spectroscopy and three-point loading test respectively. WVP was investigated using the cup method. Means and standard deviations were calculated, and the data were statistically analyzed using factorial analysis of variance test (α = 0.05). Results: Light irradiance showed highest values using no ICBs and lowest values using Pinnacle curing sleeve. Both bulk-fill composites showed higher DC mean values without ICBs and when using Sanita wrapping film for both upper and lower layers of the specimens compared to Pinnacle curing sleeve. The upper layers of composite specimens showed higher DC compared to lower layers for all experimental conditions. Both ICBs had no adverse effect on FS of both composites' upper layers. Pinnacle sleeve significantly reduced FS of both composites' lower layers. X-tra fil showed higher DC and FS compared to Tetric N-Ceram for all experimental conditions. Regarding WVP; the wrapping film showed higher WVP compared to the curing sleeve. Conclusions: Sanita wrapping film can be used as a successful ICB, without jeopardizing the concept of bulk-fill composites. Pinnacle cure sleeve can be considered an effective ICB, however its influence on properties and serviceability of bulk-fill composites remains questionable. [ABSTRACT FROM AUTHOR]

Nanozyme materials combine the advantages of natural enzymes and artificial catalysis, and have been widely applied in new technologies for dental materials and oral disease treatment. Based on the role of reactive oxygen species (ROS) and oxidative stress pathways in the occurrence and therapy of oral diseases, a comprehensive review was conducted on the methods and mechanisms of nanozymes and their dental materials in treating different oral diseases. This review is based on literature surveys from PubMed and Web of Science databases, as well as reviews of relevant researches and publications on nanozymes in the therapy of oral diseases and oral tumors in international peer-reviewed journals. Given the unique function of nanozymes in the generation and elimination of ROS, they play an important role in the occurrence, development, and treatment of different oral diseases. The application of nanozymes in dental materials and oral disease treatment was introduced, including the latest advances in their use for dental caries, pulpitis, jaw osteomyelitis, periodontitis, oral mucosal diseases, temporomandibular joint disorders, and oral tumors. Future approaches were also summarized and proposed based on the characteristics of these diseases. This review will guide biomedical researchers and oral clinicians to understand the mechanisms and applications of nanozymes in the therapy of oral diseases, promoting further development in the field of dental materials within the oral medication. It is anticipated that more suitable therapeutic agents or dental materials encapsulating nanozymes, specifically designed for the oral environment and simpler for clinical utilization, will emerge in the forthcoming future. [Display omitted] [ABSTRACT FROM AUTHOR]

Develop a sustainable bovine hydroxyapatite dental ceramic with the addition of titanium dioxide (TiO 2) nanoparticles (5 % and 8 % by weight), analyzing the outcome of this addition to the microstructure, as well as its mechanical and chemical properties, in order to evaluate whether they satisfy the International Organization for Standardization (ISO) 6872:2015 for dental ceramics or not. Disks were obtained through uniaxial followed by isostatic pressing from bovine hydroxyapatite powder and TiO 2 nanoparticles and sintered at 1300ºC for 2 h. Three experimental groups were developed (HA, HA+5 %TiO 2 and HA+8 %TiO 2) and subjected to X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), indentation fracture (IF), biaxial flexural strength (BFS) and chemical solubility test. XRD revealed, for HA group, the appearance of a peak corresponding to b-tricalcium phosphate (ß-TCP). For HA+ 5 %TiO 2 and HA+ 8 %TiO 2, the entire composition was converted into ß-TCP and calcium titanate (CaTiO 3). The SEM images showed a dense ceramic matrix and a uniform distribution of another phase in groups with TiO 2 nanoparticles. HA+ 5 %TiO 2 (1.40 ± 0.18 MPa.m1/2) and HA+ 8 %TiO 2 (1.32 ± 0.18 MPa.m1/2) showed significantly higher fracture toughness values than HA (0.67 ± 0.09 MPa.m1/2). HA showed significantly higher characteristic stress (295.8 MPa) in comparison to groups with 5 % (235.1 MPa) and 8 % (214.4 MPa) TiO 2 nanoparticles. Differences were not observed between the Weibull modulus values. The solubility results indicated that all experimental ceramics were above the 2000 ug/cm2 limit set by the ISO 6872:2015. This study proposed the development and characterization of a new ceramic for dental prosthesis made from HA extracted from bovine bones, with the intention of reusing these solids waste and transforming them into a sustainable and low-cost material. Although the experimental calcium phosphate ceramic with additions of 5 % and 8 % of TiO 2 achieved desirable mechanical properties, the chemical solubility values were very high. [Display omitted] • Bovine HA derived bioceramic with TiO 2 presents sustainability potential. • The addition of 5 % and 8 %TiO 2 significantly improved material's fracture toughness. • HA + TiO 2 bioceramic material converted microstructure to ß-TCP and CaTiO 3. • HA+TiO 2 achieved mechanical ISO standards, but failed chemical solubility limits. [ABSTRACT FROM AUTHOR]

Phosphate-based glasses are known for their excellent biocompatibility and adjustable degradation rates. In this study, we fabricated a rapidly soluble zinc-ion-releasing phosphate-based glass (RG) specifically designed for use in dental cavity liners. The aim of this study was to evaluate the ion-releasing properties and antibacterial effects of RG. Additionally, a dental resin incorporating RG was fabricated to serve as a cavity liner, and its effectiveness was investigated in vitro. The RG formulation exhibited high solubility and released high concentrations of Zn2+ at various pH values. To assess the antibacterial properties of RG, six bacterial species detected in deep carious regions were incubated in the presence of RG. In vitro antibacterial testing against six bacterial species revealed that RG exhibited strong bactericidal effects against these prevalent bacteria. Furthermore, using a dentin model infected with Lactobacillus casei or Streptococcus mutans, the experimental resin containing RG demonstrated an effective bactericidal effect in the dentinal tubules, highlighting its potential as a promising material for cavity liners or pulp-capping applications. [ABSTRACT FROM AUTHOR]

Before clinical trials are initiated, studying the mechanical performance of modern CAD/CAM restorative materials exposed to aging conditions would provide insights on their performance in service. This study evaluated the impact of thermomechanical aging on various resin composite, ceramic, hybrid, and nano-filled resin composite materials after two polymerization modes. Specimens (3 × 4 × 14 mm3) were fabricated using (n = 12 per group) a universal composite (Filtek Supreme XTE photo-polymerized for either 40 s or 120 s per layer), hybrid ceramics (BRILLIANT Crios, GC Cerasmart, Lava Ultimate, VITA ENAMIC), glass ceramics (IPS e.max CAD, VITA Suprinity PC, Straumann n!ce), or feldspar ceramics (VITABLOCS Mark II, GC Initial LRF). In each group, half of the specimens underwent thermomechanical aging. A three-point bending test was applied to all specimens and the results were statistically analyzed (α = 0.05). Glass ceramics and hybrid ceramics presented higher flexural strength values than feldspar ceramics and the universal composite before and after aging (p < 0.05). Thermomechanical cycling affected the flexural strength of all materials (p < 0.05) except Lava Ultimate, Straumann n!ce, and GC Initial (p > 0.05). The highest decrease in flexural strength after aging was found in the universal composite (40 s polymerization) (p < 0.001) and Vita Enamic (p < 0.001), while the lowest decrease was in the hybrid ceramics, Cerasmart and Lava Ultimate (p < 0.05). Extending polymerization duration reduced the aging effect on the universal composite tested. Thermomechanical aging affected the flexural strength of most materials tested. Universal composites and feldspar ceramics presented similar flexural strength values. [ABSTRACT FROM AUTHOR]

AbstractOptimal dental health significantly contributes to an individual’s physical and psychological well-being, with an increasing focus on esthetics and functionality in dental restoration procedures. This research explores the use of zirconia ceramic materials combined with calcium silicate and silver compositions as an alternative for dental crown applications. The study employs 3D finite element analysis to assess stress distribution on full crowns with composites under axial and oblique loads, aiming to understand biomechanical aspects and identify fracture resistance and failure modes. The materials include zirconia-calcium silicate-silver composites with varying volume fractions (Zr 74 to 29%, Ca2SiO4 68 to 25%, and Ag 3 to1%). Results show stress concentration at the crown intaglio surface, influenced by the material’s elastic modulus. Specifically, the C14 composite crown with Young’s modulus 90.82 GPa exhibits lower stress levels for crown 10.9 MPa at axial load and 12.77 MPa at oblique load, making it a potentially recommended choice. These findings suggest the potential of designed biomaterials, emphasizing the importance of material selection in enhancing the longevity and resilience of dental crowns. Also, the study enhances understanding of biomechanical aspects in dental crown restorations, contributing valuable insights for clinical applications. [ABSTRACT FROM AUTHOR]

Objectives: Investigate the effect of different postpolymerization protocols, aging, and 3D printing systems on the flexural strength (σ), dimensional stability, and roughness of resins used to fabricate occlusal splints, dental models, and temporary restorations. Material and methods: 180 bars (25 × 2 x 2 mm—ISO 4049) of each type of resin (T—Temporary/Cosmos Temp, Yller; OS—Occlusal splint/Cosmos Splint, Yller; MO – Models/ Cosmos Model, Yller) were printed and divided into 12 groups (n = 15) according to the factors: “Postpolymerization” (Ctr – Control; UV – Ultraviolet oven and MW – Microwave); “Printer” (SLA- stereolithography (Forms 2/Formslab); LCD- liquid crystal display (FlashForge Foto 6.0/FlashForge)) and “Aging” (TC – 10,000 thermocycling cycles and Without). Each bar was measured with a digital caliper at 11 points before and after postpolymerization to evaluate dimensional stability. The samples were subjected to the σ test (100Kgf;1 mm/min). Data was evaluated using Three- and Two-way ANOVA, and Tukey’s test (5%). Weibull analysis, Scanning Electron Microscopic and optical profilometry was performed. Results: LCD printing system and UV oven postpolymerization exhibited the highest σ (P <.05). The groups printed in SLA and post-polymerized in microwave ovens showed the greatest variations in their dimensions, for the occlusal splint resin, the OS-SLA-MW group (-4.29 ± 3.15)A showed a shrinkage of 40.2%. The resins for models (3.31 ± 0.66)A and temporary (-2.06 ± 1.52)A showed a shrinkage of 33% and 20.6%, respectively. Conclusions: LCD printing with UV light postpolymerization was the most effective method for resins used in occlusal splints, dental models, and temporary restorations. SLA printing with UV postpolymerization showed the most significant dimensional changes, leading to shrinkage in occlusal splint resins, while model resins and temporary restorations expanded. Clinical relevance: Resins for 3D printing should ideally be post-polymerized with UV light and printed using LCD technology, as this approach results in better mechanical properties and less dimensional change compared to microwave oven post-polymerization. [ABSTRACT FROM AUTHOR]

Introduction: In this study, the effects of adding titanium dioxide nanotubes (TiO2) to 3D‐printed denture base resin on the mechanical and physical properties of denture bases were examined for the first time. Methods: The specimens were digitally created using 3D builder software from Microsoft Corporation through computer‐aided design. In accordance with the test specifications for transverse strength, impact strength, hardness, surface roughness, and color stability, specimens were designed and printed with certain dimensions following relevant standards. TiO2 nanotubes (diameter: 15–30 nm and length: 2–3 μm) were added to the 3D‐printed denture base resin (DentaBase, Asiga, Australia) at 1.0% and 1.5% by weight. Flexural strength, impact strength (Charpy impact), hardness, surface roughness, and color stability were evaluated, and the collected data were analyzed with ANOVA followed by Tukey's post hoc test (α = 0.05). Field emission scanning electron microscopy (FESEM) and energy dispersive x‐ray spectroscopy (EDX) mapping were used to evaluate the dispersion of the nanotubes. Results: Compared with those of the control group (0.0 wt.% TiO2 nanotubes), the average flexural, impact, and hardness values of the 1.0 and 1.5 wt.% TiO2 nanotube reinforcement groups increased significantly. Both nanocomposite groups showed significant color changes compared to that of the pure resin, and there was a considerable reduction in the surface roughness of the nanocomposites compared to that of the control group. Conclusion: Adding TiO2 nanotubes to 3D‐printed denture base materials at 1.0 and 1.5 wt.% could enhance the mechanical and physical properties of the material, leading to better clinical performance. Clinical Significance: In terms of clinical applications, 3D‐printed denture base material has been shown to be a viable substitute for traditional heat‐cured materials. By combining this with nanotechnology, existing dentures could be significantly enhanced, promoting extended service life and patient satisfaction while addressing the shortcomings of the current standard materials. [ABSTRACT FROM AUTHOR]

To examine the effect of ionizing radiation on fluoride release from restorative dental materials, samples of Equia Forte HT, Fuji Triage, Fuji IX, Cention Forte, Activa Presto, Beautifil II, and Luminos (n = 10) were made in Teflon molds and divided into a control group and an experimental group. The experimental group was exposed to ionizing radiation for a total of 35 days (70 Gy, 2 Gy per day). The fluoride release was measured with a fluorine-selective electrode. The median recorded fluoride values were higher with Equia Forte HT, Fuji Triage, and Fuji IX compared to others during the entire period in both groups. With Activa Presto, a higher release of fluoride was recorded in the experimental group on the first day of irradiation, while a higher release was recorded in the control group, as well as with Luminos and Beautifil II. With Cention Forte, there was no significant difference in fluoride release between the experimental and control groups except on the sixth day. With Fuji Triage and Fuji IX, the release of fluoride was higher in the experimental group compared to the control group, while with Equia Forte HT, there was no difference between the groups. In conclusion, ionizing radiation has no major effect on fluoride release in all the tested materials. [ABSTRACT FROM AUTHOR]

Background: Different pulp capping materials have different origins and compositions, require different preparations, and may vary in their bioactive properties. Aim: The purpose of this study was to evaluate the antibacterial activity, biocompatibility, and mineralization‐inducing potential of calcium silicate‐based pulp capping materials. Design: Six contemporary calcium silicate‐based cements, ProRoot MTA, MTA Angelus, Biodentine, EndoSequence, NeoMTA 2, and NeoPutty, were evaluated. The antibacterial effects of these materials against Streptococcus mutans UA159 and Enterococcus faecalis ATCC 29212 were determined by the agar diffusion assay and the direct culture test. The biocompatibility and mineralization‐inducing potential of these materials in preodontoblastic 17IIA11 cells were evaluated by the MTT assay and by Alizarin Red S staining, respectively. Results and Conclusion: In agar diffusion test, only Biodentine showed distinct antibacterial effects against S. mutans. All the tested materials, however, showed antibacterial effects against S. mutans and E. faecalis in the direct culture test, with Biodentine showing the strongest growth inhibition against both S. mutans and E. faecalis. All the tested materials showed acceptable biocompatibility and mineralization‐supporting potential in our experimental conditions. In summary, ProRoot MTA, MTA Angelus, Biodentine, EndoSequence, NeoMTA 2, and NeoPutty demonstrated acceptable in vitro antimicrobial, biocompatible, and mineralization‐supporting properties. [ABSTRACT FROM AUTHOR]

Background: Children with dental caries are treated with stainless steel metal crowns (SSC), but the aesthetics and precision still need to be improved. Currently, both 3D‐printed resin crowns (PRC) and computer‐aided design/computer‐aided manufacture (CAD/CAM) resin crowns (CRC) meet the clinical requirements for crown applications in terms of strength, production time, cost, and aesthetics. Aim: This study replaced SSC with customized resin crowns by 3D printing and CAD/CAM. Design: In this study, PRC, CRC, and SSC were used for incisor and molar restorations, and 60 crowns were made with 10 for each group. The fabrication efficiency, surface characteristics, marginal fit, and stability of the two different crowns were evaluated. Results: PRC and CRC show superior color and surface characteristics, though production times are longer (5.3–12.4 times and 3.3–9.1 times, respectively) than for SSC (p <.05). They, however, can be completed within 80 min. Edge gaps for PRC and CRC are significantly lower (13.0–19.2 times and 13.0–13.7 times) than for SSC (p <.05). All materials exhibit good stability. Conclusion: The 3D‐PRCs and CAD/CAM resin crowns may replace SSCs as a potential choice for clinical child caries. [ABSTRACT FROM AUTHOR]

Background: The evidence underpinning caries management for children has progressed dramatically over the past 20 years. Anecdotally, this is not reflected in the teaching provided to undergraduate dental students, with the ongoing teaching of outdated methods within some dental schools. Aim: To capture the current undergraduate teaching provision and clinical treatment experience requirement relative to caries management in paediatric dentistry in UK dental schools. Design: Cross‐sectional analysis of current teaching methods on paediatric caries management was obtained using a piloted online data collection form. Question content included current caries teaching methods, assessment of student exposure and competence. The results were analysed descriptively. Results: Of the 16 UK dental schools, 14 participated. Discrepancy in teaching content was apparent. Many schools (n = 9) taught biological caries management through therapeutic fissure sealants, yet this was not reflected in assessment and clinical requirements. Some schools (n = 4) taught amalgam placement in children, and most (n = 12) operatively taught treatments that would no longer be routinely provided in general dental practice in the UK, including primary tooth pulpotomy. Conclusion: There is substantial variation in the paediatric caries management techniques that are taught across UK dental schools, demonstrating a need for a national consensus to address these disparities. [ABSTRACT FROM AUTHOR]

Background: Paediatric‐preformed zirconia crowns have been associated with several issues, primarily their inability to be crimped and the need for extensive tooth preparation. Additionally, the capacity to adjust the size, shape, and fit of these crowns is very limited. Aim: To evaluate and compare the fracture strength of four different types of dental crowns intended for paediatric patients. Design: The fracture resistance of four types of paediatric crowns was evaluated using the universal testing machine; freshly extracted primary molars received one of the following: preformed zirconia crowns, custom‐made computer‐aided design and computer‐aided manufacturing (CAD–CAM) zirconia crowns, custom‐made CAD–CAM ceramic crowns, and custom‐made CAD–CAM hybrid composite crowns. Data were statistically compared using the Kruskal–Wallis test followed by the Bonferroni test, and the level of significance was set at 5%. Results: Results showed that there was a statistically significant difference among the four groups (p <.001). The highest value of fracture force was observed for the milled zirconia crown and the lowest for the prefabricated zirconia. Conclusion: The implementation of the CAD–CAM digital crown fabrication technique has the potential to address issues associated with preformed crowns in paediatric patients, particularly in terms of fracture resistance. [ABSTRACT FROM AUTHOR]

Surface properties of dental implant materials, whether they are physical, chemical, mechanical, or biological, influence the processes of osseointegration and the development of the biological seal at the implant-soft tissue interface. In turn, successful occurrence of these steps prevents peri-implant diseases. This goal can be achieved through the application of surface treatments of a bioactive nature leading to an effective implant-bone union. Our work focuses on a thorough characterization of bioactive surface properties obtained through alkaline treatment on two different surfaces used in the dental implant industry, namely, a surface blasted with calcium phosphate particles and a micro-arc anodized surface. The results show that the alkaline treatment modifies the surface properties of both blasted and anodized samples. Modification is related to the formation of a nanoporous amorphous sodium titanate hydrogel that exhibits high bioactivity in an SBF medium. To assess in vitro biocompatibility and bioactivity, a 48-hour cell culture assay was conducted using dental pulp mesenchymal stem cells. All samples demonstrated cell adhesion, growth, and intercellular communication, indicating that the surfaces are biocompatible and non-cytotoxic. However, samples subjected to alkaline treatment exhibited qualitatively superior bioactivity and in vitro behavior and among them, the blasted sample produced the surface with best performance. [ABSTRACT FROM AUTHOR]

Copyright of Quintessenz der Zahntechnik is the property of Quintessenz Verlags GmbH and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Highlights The characterization of S. persica (Salvadora persica) extract, which involved evaluating its antibacterial activity, demonstrated the extract's strong efficacy. Additionally, incorporating it into PMMA/HA showcased the composite's good antibacterial activity. The objective of this work is to evaluate how the incorporation of S. persica extract affects the wear resistance of the dental composite PMMA/HA, considering the critical importance of wear resistance in dental applications. The wear response of this biocomposite was tested against an Alumina ball using a pin‐on‐disc tribometer. Initially, the hydroxyapatite (HA) micro particles demonstrate a remarkable influence on wear behavior when incorporated at an optimal percentage (10%wt). This optimal inclusion rate not only significantly increases the wear rate but also instigates a shift in the wear mechanism, favoring abrasive wear while minimizing adhesive wear comparing to PMMA. The addition of the extract nanoparticles to the composite PMMA/HA decreases the wear rate except the composite containing 10 wt% of each filler. Additionally, it introduces adhesive wear, in addition to the existing fatigue and abrasion wear. Thus, the composite PMMA/HA could accommodate up to 10 wt% of the S. persica extract as the optimal percentage that provides antibacterial activity to this biocomposite without exhibiting a deterioration in wear performance. The evaluation of the effect of incorporating S. persica extract, which provides antibacterial activity, on the wear resistance of the PMMA/HA dental composite generally demonstrates a reduction in this property. The addition of S. persica extract introduces adhesive wear in addition to the fatigue and abrasion wear already present in the PMMA/HA composite. The composite PMMA/HA can accommodate up to 10 wt% of S. persica extract without compromising its wear performance. [ABSTRACT FROM AUTHOR]

Objectives: This study aimed to evaluate the effect of whitening toothpastes on the surface roughness and colour change of CAD-CAM materials. Materials and methods: A total of 96 samples (2 × 10 × 12 mm3) were prepared from Cerasmart (CS) and Celtra Duo blocks. Celtra Duo samples were divided into two groups. One group was fired with glaze paste (CDG) and the other was not treated (CD). All groups were then divided into 4 subgroups (n = 8). The groups were brushed with conventional (Colgate™ Max Fresh), silica (Opalescence™), charcoal (Curaprox™ Black in White) and blue covarine (Signal™ White Now) toothpastes for 30,000 brushing cycles. The initial and final surface roughness values were measured with contact profilometer and a dental spectrophotometer used for obtaining colour values. One sample from each brushed group was analyzed using a scanning electron microscope. Data was analyzed with Kruskal-Wallis and Mann-Whitney tests (p = 0.05). Results: The surface roughness of CS samples brushed with Opalescence™ and Curaprox™ was significantly higher than CD and CDG. Surface roughness change values of CS samples brushed with Curaprox™ were significantly higher than the CD and CDG. Curaprox™ brushed samples showed significant difference in colour change values for all materials. Conclusions: Brushing increases the surface roughness of CAD-CAM ceramic materials. The roughness of resin-based materials is higher than zirconia-reinforced lithium silicates. Silica-contained toothpastes may cause discoloration of nanoceramic and zirconia-reinforced glass ceramic restorations. Clinical relevance: It should be clinically considered that whitening toothpastes may cause roughness in ceramic materials and change the desired color. [ABSTRACT FROM AUTHOR]

Objective: Customized nonabsorbable membranes are widely used in severe alveolar bone defects and provide sufficient and precise regenerated bone tissue for subsequent dental implant placement. Although 3D-printed polyetheretherketone (PEEK) meshes have confirmed successful use in clinical cases, the performance of a PEEK mesh is not satisfactory. Compared with PEEK, polyetherketoneketone (PEKK) has better mechanical and processing properties. However, whether PEKK is suitable for making customized membranes remains unclear. The objectives of this study were (1) to evaluate the printing precision, surface characteristics, mechanical characteristics and biocompatibility of the PEKK mesh and (2) to compare the properties of the PEKK and PEEK meshes. Materials and methods: Both PEKK and PEEK meshes were designed and manufactured via additive manufacturing technology combined with computer-aided design (CAD). The printing precision was evaluated with a high-resolution extraoral scanner. The surface characteristics were evaluated with a contact angle system and three-dimensional optical microscopy. The mechanical characteristics were evaluated via three-point bending tests and tensile tests. The biocompatibility was evaluated with a CCK-8 assay, live/dead viability assay and qRT-PCT. Results: Compared with the PEEK mesh, the PEKK mesh exhibited better control in terms of the thickness and aperture area. Both the PEKK mesh and the PEEK mesh had a hydrophobic surface, but the PEKK mesh had a smoother surface. Compared with the PEEK mesh, the PEKK mesh has better compression and tensile properties. Both the PEKK mesh and the PEEK mesh had good biocompatibility. The proliferation of cells on the PEKK mesh was slightly lower than that on the PEEK mesh. Conclusions: Compared with PEEK mesh, PEKK mesh has greater printing accuracy, smoother surfaces, better mechanical properties and similar biocompatibility and is expected to be used in the production of customized barrier membranes for the augmentation of severe bone defects. To ensure the stability of the mesh for clinical application, it is best to control the aperture diameter of the PEKK mesh to less than 2 mm with a thickness of 0.2 μm. [ABSTRACT FROM AUTHOR]

Purpose: Current denture base resins lack adequate strength and antimicrobial properties, necessitating the exploration of alternative solutions. The purpose of this study was to evaluate the effects of curcumin incorporation on the physico-mechanical properties of heat-cured denture base resin, filling a gap in the literature regarding this correlation. Methods: Heat-cured denture base resin was supplemented with increasing concentrations of curcumin (CR). Groups were designated as CR-0 (0%), CR-0.05 (0.05%), CR-0.10 (0.10%), CR-0.50 (0.50%), and CR-1 (1%), based on the increasing concentrations of curcumin incorporated into the material. Physico-mechanical properties, including flexural strength, surface roughness, fracture toughness, impact strength, and color difference, were evaluated following the testing standards. Statistical analysis involved Kruskal-Wallis ANOVA followed by Dunn's test for multiple comparisons, with significance set at P ≤ 0.05 and Bonferroni's correction applied to p-values. Results: Flexural strength peaked at 153.80 MPa in the CR-0.10 group, while surface roughness was lowest at 0.14 micrometers in the CR-0.50 group. Fracture toughness reached its highest value at 1.80 kJ/m^2 in the CR-0.05 group, and impact strength was greatest at 6.52 Joules in the CR-0.05 group. Additionally, color difference was least pronounced in the CR-0.50 group. Flexural strength, surface roughness, fracture toughness, impact strength, and color difference varied significantly among the control group and different curcumin concentrations (P < 0.05). Conclusions: Incorporating curcumin into denture base resin alters both optical and mechanical properties. Further research is required to validate the findings and determine the optimal curcumin concentration without compromising the material efficacy. [ABSTRACT FROM AUTHOR]

Background: Calcium silicate-based sealer has favorable properties for root canal filling, including hydroxyapatite formation during the setting process. However, this process can cause difficulty during post space preparation when the sealer is set. Additionally, the remaining sealer could interfere with the bond strength of fiber post to root canal dentin. The different adhesive strategies and fiber post cementation time may affect the bond strength of the fiber post. Thus, the objective of this study was to evaluate the effect of etching modes of Scotchbond™ Universal Plus adhesive and post cementation time on the push-out bond strength of a fiber post cemented in root canals obturated with calcium silicate-based sealer. Methods: Fifty-four teeth were randomly allocated to 6 groups (n = 9) based on etching modes: self-etch (SE) or etch-and-rinse (ER); post space preparation and cementation time: immediate (Im) or 7-day delayed (De): Im-Im, Im-De, and De-De. The root canals were obturated with calcium silicate-based sealer and the post space preparation was performed. The fiber post was cemented using RelyX™ Universal resin cement according to each group's design. For the push-out bond strength test, 1-mm slices of the coronal, middle, and apical regions were tested using a universal testing machine. The failure mode analysis was determined using a stereomicroscope. The data was analyzed with three-way analysis of variance. Results: No negative effects of etching modes, post space preparation or cementation time on push-out bond strength were detected (p > 0.05). Additionally, the root canal region also did not significantly affect the bond strength (p > 0.05). Conclusion: No significant differences were observed between the etching modes, post space preparation and cementation time and among root canal regions. Clinical relevance: The different etching modes of adhesive and post cementation time did not affect the bond strength of fiber post in calcium silicate filled-root canal. [ABSTRACT FROM AUTHOR]

Summary Background Study design Objectives Methods Results Main limitations Conclusions Dentigerous cysts are well‐known congenital defects in horses, and the literature on this condition is extensive. Recently, a third type of dentigerous cyst, associated with an exostosis arising from the temporal bone, has been described. Today, computed tomography (CT) is often available and provides detailed information about the exact location and extent of dentigerous cysts, allowing for the description of new findings.This is a case series outlining the clinical, radiographic and computed tomographic features of dentigerous cysts in seven horses presented to the Equine Clinic at the Vetsuisse Faculty, University of Zurich, Switzerland.The aim of this case series was to describe the radiographic and computed tomographic findings, and the occurrence of exostoses arising from the temporal bone, in horses with dentigerous cysts.The medical records of the Equine Hospital at the University of Zurich were reviewed for horses admitted with dentigerous cysts between 2007 and 2023. Data collected and analysed included patient signalment, clinical history, clinical signs and their duration prior to referral, diagnostic imaging results, treatment and outcomes.The most common location for the cysts was the base of the ear, although in one case, the maxillary sinus was involved. Of the seven cases, four were Icelandic horses. CT proved superior to standard radiography for determining the extent and precise location of the cysts, as well as for identifying dental material and exostoses in the temporal region. CT also facilitated detailed surgical planning. All cysts were surgically removed with good long‐term outcomes.Overall, the incidence of dentigerous cysts in horses was low. The relatively high occurrence of dentigerous cysts in Icelandic horses in this study is an interesting finding, though the small sample size calls for further research.Two of the cases in this series were similar to a recently described variant of a ‘temporal dentigerous cyst associated with an exostosis in the temporal region’ and were closely connected to the bony structure and draining tract. [ABSTRACT FROM AUTHOR]

Background: It was aimed to investigate the effect of sandblasting and laser surface treatment on shear bond strength in composite restoration repair in vitro. Methods: A micro-hybrid composite (Filtek Z250, 3 M-ESPE, USA) was used to prepare 120 samples. The samples were subjected to a thermal cycle test 5,000 times between 5 and 55 0C, and they were randomly divided into 12 groups (n = 10). No surface treatment was performed in Groups 1 to 4, which were designed as control groups. The surfaces of the samples in Groups 5 to 8 were sandblasted with a Cojet device, and the surfaces of the samples in Groups 9 to 12 were applied Er, Cr: YSGG laser. After the sample surfaces were divided into groups with and without acid etching, universal adhesive was applied, and the repair process was performed using Filtek Z250 or nano-filled resin composite (Filtek Ultimate, 3 M-ESPE, USA). The thermal cycle test was repeated 5,000 times between 5 and 55 0C on all repaired samples. The repair shear bond strength of the samples was measured using a universal testing device (Shimadzu IG-IS, Kyoto, Japan). The fracture types were evaluated by optical microscopy and scanning electron microscopy (SEM). Statistical analyses of the findings were evaluated by the Kruskal Wallis test and Mann Whitney U test at 0.05 significance degree. Results: The highest mean shear bond strength values were obtained from the samples sandblasted with CoJet, followed by Er, Cr: YSGG laser, and the control group. It was determined that there was a significant difference between the mean shear bond strength values obtained from the control group and the other surface treatment groups (p < 0.05). In general, significantly higher mean shear bond strength values were obtained when the universal adhesive was applied in total-etch mode compared to the application in self-etch mode (p < 0.05). Additionally, it was determined that higher shear bond strength values were obtained with Filtek Ultimate compared to Filtek Z250 (p < 0.05). Conclusion: Within the limitations of this study, it can be concluded that the use of universal adhesive in total-etch mode, in addition to surface treatments on the resin composite surface in the repair protocol and the use of nano-filled resin composite as repair material can increase the mean shear bond values in repair. [ABSTRACT FROM AUTHOR]

Objectives: To evaluate the effect of the universal and rapid autoclave cycles on the mechanical properties and surface roughness of nickel-titanium archwires following clinical use. Material and methods: Thirty-six NiTi archwires (0.016 × 0.022 inch) were equally divided into a control group (Group A) and 2 experimental groups (Group B & C). Wires in group A were tested in the "as-received" form. Wires in the two other groups were installed in patients mouth for 4 weeks, and then autoclaved using the rapid-cycle (Group B) or the universal-cycle (Group C). All wires were subjected to 3-point bending test to calculate the elastic limit, modulus of elasticity, spring-back, yield strength, resilience and toughness. Atomic force microscopy (AFM) was used for surface roughness qualitative and quantitative analysis. Results: Group B showed significantly higher values of elastic limit, modulus of elasticity, resilience, yield strength and toughness than the other two groups. No significant differences were detected between groups A and C (P > 0.05). Group B showed significantly lower average surface roughness than the other two groups, but no significant differences were detected between groups A and C (P > 0.05). Conclusions: The mechanical properties and surface roughness of clinically used NiTi wires were less affected by the universal-cycle than the rapid-cycle autoclaving. However, the difference between the effect of both autoclave cycles was diminutive. Clinical relevance: The mechanical properties and surface roughness of the tested NiTi wires were not notably altered by clinical use and autoclaving. [ABSTRACT FROM AUTHOR]

Background: This clinical study aims to compare postoperative pain after single-visit root canal treatment of teeth with asymptomatic apical periodontitis using epoxy-resin-based AH Plus and calcium silicate-based Endosequence BC sealers with or without sonic activation. Methods: This study included 72 individuals with one first or second mandibular premolar tooth with asymptomatic apical periodontitis. They were randomly divided into four groups according to the root canal sealer (AH Plus or Endosequence BC) and activation protocol (sonic activation or non-activation) (n = 18). The participants were ask to rate their postoperative pain intensity on a NRS scale as none, minimal, moderate, or severe after 24 h, 48 h, 72 h, and 7 days following treatment. Patients were also asked to record the number of prescribed analgesic medication tablets (400 mg of ibuprofen) taken. Statistical analysis were performed using the Mann-Whitney U test, the Friedman test, the Spearman's correlation test, the Chi-square test. Significance level was established at 0.05. Results: There was no statistically significant difference in postoperative pain scores or analgesic intake between AH Plus and Endosequence BC sealers regardless of the activation protocol (p > 0.05). There was no statistically significant difference in postoperative pain scores between the sonic activation and non-activation groups (p > 0.05). A weak positive correlation was detected between Endoactivator sonic activation and sealer extrusion (r = 0.36). Conclusions: AH Plus and EndoSequence BC root canal sealers showed similar results in terms of prevalance and intensity of postoperative pain. Sonic activation and non-activation groups had similar postoperative pain scores. Clinical trial registration: The study was retrospectively registered with ClinicalTrials.gov (NCT06403293). Date of Registration: 07/05/24. [ABSTRACT FROM AUTHOR]