Search

The enzyme-linked immunosorbent assay (ELISA) is one of the most commonly implemented clinical diagnostic tools for the detection and quantification of protein biomarkers. However, conventional ELISA tests require sophisticated infrastructure, expensive reagents, long assay time, and expertise for operation, which are not often easily accessible in resource-limited settings. Microfluidic ELISA-chip based point-of-care (POC) testing allows miniaturization and integration of complex functions that facilitate their usage in limited-resource settings. The current work demonstrates a simple, portable, low cost and equipment-free paper/poly(methyl methacrylate) (PMMA) integrated microfluidic ELISA-chip as a POC device with a visual distance-based readout for quantitative detection of clinical biomarkers. The integrated paper/PMMA ELISA-chip utilizes the movement of immunoassay complexes with magnetic beads by a permanent magnet in a PMMA part of the compartment. The target concentration is translated into a visual distance signal readout for quantitative detection of biomarkers in a μPAD. Because it does not require sophisticated instruments and has the added advantages of low cost, easy operation, and disposability with quantitative visual readout, the paper/PMMA ELISA-chip holds great promise for portable detection of target bioanalytes as a POC diagnostic tool in resource-limited setups. [ABSTRACT FROM AUTHOR]

This paper reports a simple innovative method to align magnetic cellulose fibers by using a simple permanent magnet to fabricate unidirectional magnetic papers. Magnetic cellulose fibers were made by in situ synthesis of magnetite nanoparticles on alpha cellulose pulp extracted from American southern pine. Scanning electron microscope micrographs and energy dispersive X-ray spectroscopy maps indicated that magnetite nanoparticles completely covered the cellulose fibers. Suspensions of magnetic cellulose fibers were prepared at three levels of concentration (0.02, 0.04, and 0.08 g/L) and poured into the designed magnetic forming machine. Flow rate of suspension into the forming column was adjusted at 0, 0.3, 0.5, and 1 cm/s. The strength of the applied external magnetic field was the same in all cases and lower than 0.18 T. Orientation analysis indicated that the designed magnetic forming machine has a high performance to be used for aligning magnetic cellulose fibers and fabricating unidirectional magnetic cellulose papers. Observed anisotropic magnetic and mechanical properties confirmed the unidirectional structure. [ABSTRACT FROM AUTHOR]

This paper deals with the digital implementation of a motor control algorithm based on a unified machine model, thus usable with every traditional electric machine type (induction, brushless with interior permanent magnets, surface permanent magnets or pure reluctance). Starting from the machine equations in matrix form in continuous time, the paper exposes their discrete time transformation, suitable for digital implementation. Since the solution of these equations requires integration, the virtual division of the calculation time in sub-intervals is proposed to make the calculations more accurate. Optimization of this solver enables faster runs and higher precision especially when high rotating speed requires fast calculation time. The proposed solver is presented at different implementation levels, and its speed and accuracy performance are compared with standard solvers. [ABSTRACT FROM AUTHOR]

To reduce the influence of the permanent magnet (PM) installation error on the electromagnetic characteristics of the outer rotor permanent magnet synchronous motor (OPMSM), the rotor structure of the OPMSM is optimized in this paper. The optimization method of adding auxiliary teeth on the surface of the rotor core is studied, and the influence of different auxiliary teeth heights on the electromagnetic performance of OPMSM is analyzed. It is found that adding auxiliary teeth with suitable height can greatly reduce the installation error of the PM, increase the mechanical stability of the motor, and ensure that the electromagnetic characteristics of the motor remain at a good level. Firstly, the topology and parameters of the motor proposed in this paper are introduced and analyzed. Secondly, the influence of PM installation error on the electromagnetic performance of the motor is analyzed based on the finite element method (FEM), and the necessity of eliminating PM installation error is demonstrated. Then, the parametric scanning method is used to analyze the influence of auxiliary teeth height change on the electromagnetic performance of the motor, and the selection standard of the optimal auxiliary teeth height is determined. By comparing and analyzing OPMSM with different sizes and different pole–slot ratios, the universality of the conclusions is demonstrated. [ABSTRACT FROM AUTHOR]

At present, low-speed high-torque permanent magnet motors are widely used in the sampling industry, manufacturing industry and energy industry. However, the research on low-speed high-torque permanent magnet motors is far from enough. The primary difficulty in the initial design of low-speed high-torque permanent magnet motors is the selection of pole–slot ratio. The pole–slot ratio has a great influence on the electromagnetic performance such as torque ripple and the maximum output torque of low-speed motors. Choosing the appropriate pole–slot ratio scheme can make the design of a low-speed motor more efficient. In addition, the optimization design of the motor is also a necessary process. At present, there are many studies on optimization algorithms. However, the research on sample point sampling and surrogate model fitting is not enough. Choosing the appropriate sample point sampling method and surrogate model fitting method can help one obtain a more accurate surrogate model, which lays a foundation for the optimization of the motor. Based on the above analysis, this paper first selects four representative pole–slot ratio schemes for comprehensive comparison of their electromagnetic performances. Secondly, two sample point sampling methods and three surrogate model fitting methods are combined to obtain six surrogate models, and the accuracy of the six surrogate models is compared and analyzed. Finally, a 37kW,160rpm prototype is made, and the comparison of the surrogate model optimization prediction results, the finite element simulation calculation results and the measured results is carried out to further prove the accuracy of the selected surrogate model. The work performed in this paper provides a certain reference value for the initial design and optimization experiment design of low-speed high-torque permanent magnet motor. [ABSTRACT FROM AUTHOR]

In this paper, a control scheme based on current optimization is proposed for dual three-phase permanent-magnet synchronous motor (DTP-PMSM) drive to reduce the low-frequency temperature swing. The reduction of temperature swing can be equivalent to reducing maximum instantaneous phase copper loss in this paper. First, a two-level optimization aiming at minimizing maximum instantaneous phase copper loss at each electrical angle is proposed. Then, the optimization is transformed to a singlelevel optimization by introducing the auxiliary variable for easy solving. Considering that singleobjective optimization trades a great total copper loss for a small reduction of maximum phase copper loss, the optimization considering both instantaneous total copper loss and maximum phase copper loss is proposed, which has the same performance of temperature swing reduction but with lower total loss. In this way, the proposed control scheme can reduce maximum junction temperature by 11%. Both simulation and experimental results are presented to prove the effectiveness and superiority of the proposed control scheme for low-frequency temperature swing reduction. [ABSTRACT FROM AUTHOR]

The single axis linear displacement measurement system of CMM is composed of grating ruler, servo motor and linear motion mechanism. Although the measuring accuracy of grating ruler is high, the accuracy of servo motor and linear motion mechanism is low. Therefore, the complex structure limits the measurement accuracy of the linear displacement measurement system. This paper introduces a novel linear displacement measurement system named magnetic levitation ruler. According to the working principle of grating ruler and the characteristics of magnetic levitation technology, the magnetic circuit design and structural design of magnetic levitation ruler are completed in this paper. The mover core of the magnetic levitation ruler is in the stable working magnetic field provided by the stator yoke. The horizontal control coil wound on the mover core can obtain more stable ampere force to improve the control accuracy of the mover core displacement. Therefore, the mover core can be moved in step mode, and the length of each step is fixed. Each step is the minimum scale of the magnetic levitation ruler. Therefore, the mover core can implement displacement measurement while moving in a linear motion. This paper analyzes the working principle of levitation, horizontal motion, and displacement measurement of magnetic levitation ruler, and determines the structural materials and parameters of magnetic levitation ruler with the help of finite element analysis software. The simulation results show that the levitation force of the magnetic levitation ruler is proportional to the current passing through the levitation coils, and the thrust of the horizontal control coil is less disturbed by the magnetic field. Compared with the linear displacement measurement system with rotational servo motor or permanent magnet synchronous linear motor as the core, the magnetic levitation ruler has stable magnetic field, strong controllability, high integration, and is easier to achieve high-precision control. [ABSTRACT FROM AUTHOR]

Examines the use of permanent magnet for measuring the moisture content of wood chips, pulp and brown stock for the paper industry. Nuclear magnetic resonance measurement system; Accuracy of water measurement; Pore moisture and surface moisture.

Permanent-magnet-assisted synchronous reluctance motors (PMA-SynRMs) are widely used in modern industry as a kind of electromagnetic energy conversion device with high output torque, high power density, high efficiency, and excellent speed regulation. In this paper, an asymmetric-rotor PMA-SynRM combined with a Halbach array is proposed based on the conventional PMA-SynRM without modifying the amount of permanent magnet. With the finite element no-load analysis, it is proven that the permanent magnet arrangement of this method can achieve better flux focusing effect and magnetic-axis-shift (MAS) effect. A significant increase and shift of the air-gap magnetic density has also been observed. Meanwhile, the load simulation demonstrated that the proposed model possesses higher utilization of permanent magnet torque and reluctance torque compared to the conventional model. In addition, a multi-objective optimization has been performed for the rotor structure of the proposed model, and the optimized model improved the average torque by 25.32% and reduced the torque ripple by 76.92% compared to the conventional model. Finally, the constant power speed range (CPSR) performance and anti-demagnetization performance have been analyzed for the three models. The results showed that the proposed and optimized models performed better on constant power speed range, and all three models of permanent magnets had good anti-demagnetization performance. The maximum demagnetization rate of the optimized model is reduced by 13.84% compared to the proposed model at an operating condition of 200 °C and nine times the rated current. [ABSTRACT FROM AUTHOR]

A hybrid excitation variable-leakage-flux machine (HE-VLFM) for electric vehicles is presented in this paper, which places the excitation windings on the outer side of the stator and provides an axial magnetic field through the magnetic-conducting ring and magnetic-conducting bridge. The HE-VLFM proposed in this paper has a rotor permanent magnet to provide the main magnetic field and an excitation winding to provide a variable auxiliary magnetic field, which can fulfill the requirements of the electric vehicle drive system with large torque at low-speed and wide speed regulation range. The electromagnetic performance of the proposed HE-VLFM is evaluated using the equivalent magnetic circuit method and three-dimensional finite element analysis, and the results show that the HE-VLFM has a well-developed regulating flux capability. [ABSTRACT FROM AUTHOR]

Magnet cracking is a common issue in external rotor motors. To investigate the causes of magnet cracking and propose solutions, the authors consider the effects of magnet shape, magnet and yoke material fit on the motor rotor magnets, perform a static analysis of the motor rotor. The simulation and test results show that the stress distribution of tile‐shaped magnets is better than that of rectangular magnets. The highest safety margin of 56.41% is achieved for the magnet and yoke material fit of DT4/N35(EH). The maximum force of the permanent magnet (PM) exceeds 22.38% of the stress limit when the material fit is DT4/SmCo28, which can lead to cracks in the PM. The results of this paper have important reference significance for the structural design of the external rotor motor and their safe and reliable operation. [ABSTRACT FROM AUTHOR]

There is not only thrust but also normal force between the primary and secondary components for the single‐side flat plate permanent magnet linear synchronous motor (PMLSM). The normal force will fluctuate periodically, which will cause friction perturbation and finally affect the positioning accuracy of linear feed system. For the single‐side flat plate PMLSM, the variation law of normal force ripple under the coupling effect of multiple effects is studied, and the method of primary component segmental design to suppress it is proposed. Firstly, the influence of the cogging effect, the end effect and the armature reaction on the normal force ripple is analysed. Meanwhile the mathematical model of normal force ripple is established. Secondly, the PMLSM with segmental primary component is introduced and its suppression mechanism to the normal force ripple is expounded. On this basis, a scheme combining the non‐integer pole slot matching with the primary component segmental design is proposed to further suppress the normal force ripple. Finally, an 18‐slot 96/5‐pole prototype is taken as an example to carry out the finite element simulation and experimental test, of which the results verify the research theory in this paper. [ABSTRACT FROM AUTHOR]

The article discusses the importance of energy in sustainable development and the need for research and development in energy conversion systems. It highlights the limitations of current energy systems and the goal of achieving sustainable and environmentally friendly energy solutions. The article also provides an overview of a research topic on recent developments in energy conversion systems, including papers on topics such as piezoelectric materials, corrosion control methods, lithium-ion batteries, renewable off-grid mini-grids, and materials for fuel cells. The research topic has received positive responses and has generated significant interest. The article concludes by emphasizing the importance of ongoing research for a more sustainable and energy-efficient future. [Extracted from the article]

Copyright of Przegląd Elektrotechniczny is the property of Przeglad Elektrotechniczny and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper presents research on an unconventional electric machine. It is a hybrid excited machine which includes the features of three types of machines: the Permanent Magnet Synchronous Machine, the Synchronous Machine, and the Synchronous Reluctance Machine. Therefore, a broad literature review related to the above-mentioned types of machines was constructed. The well-known Permanent Magnet assisted Synchronous Reluctance Machine joins features of Permanent Magnet Synchronous Machine and Synchronous Reluctance Machine topologies. This paper shows the results of the innovative design of the Hybrid Excited Permanent Magnet assisted Synchronous Reluctance Machine, which additionally has advantages of the Synchronous Machine. In the article the basic methods of electromagnetic flux control and the designs using them are also presented. Finally, the results of simulation studies of the effect of the stator skew on the machine performance are described. [ABSTRACT FROM AUTHOR]

At present, a large number of inefficient induction motors (IMs) are still being used in various industrial fields, resulting in a huge waste of energy. Obviously, it is expensive to replace all these machines with high-efficiency motors. Therefore, this paper will investigate the method of low-cost modification of inefficient IMs and propose a low-cost permanent magnetization remanufacturing (PMR) method that can make full use of the original structure of IMs. The PMR method converts the IM's rotor into a permanent magnet (PM) rotor by directly milling slots in the original rotor and embedding PMs, thus improving the efficiency of the original motor to meet the IE4 standard. Firstly, this paper proposes the PMR process of IM, and based on this process, a Y2-132M1-6 IM is designed for remanufacturing, and the performance of the motor before and after the PMR is compared through finite-element analysis. Then, this paper researches the factors that may affect the starting performance and rated performance of the motor in the PMR design. Finally, based on the PMR design scheme, the Y2-132M1-6 IM is remanufactured into an experimental prototype. The total cost of the PMR is calculated and the performance improvement is tested through experiments. [ABSTRACT FROM AUTHOR]

This paper sets forth a thorough procedure to design surface-mounted permanent magnet synchronous generators. Since synchronous generators generate the majority of electrical energy, their relevance in society nowadays is substantial. As a consequence, the methodology to design these electrical machines also holds great importance. However, even though a considerable amount of works addresses the matter, it is difficult to find a complete and thoroughly explained design procedure. The proposed method is based on analytical equations to fully consider PM generator fundamentals with a few simplifications, which implies in a considerable number of design equations and parameters. Differently from most papers on the design of PM synchronous generators, a significant level of detail and explanation is presented, all design choices are discussed, and the suggested ranges for the design parameters are shown. This results in a straightforward procedure that allows non-experienced designers to easily replicate the results and effectively enhance the comprehension of permanent magnet synchronous machines, and provides a guideline for researchers from other fields who may need to understand and perform a synchronous generator design. To show the effectiveness of the proposed design procedure, a PM generator is designed, and the results are compared with a finite element simulation, showing good accuracy. [ABSTRACT FROM AUTHOR]

In the last decade, permanent magnet (PM)-free or hybrid PM machines have been extensively researched to find an alternative for high cost rare-earth PM machines. Brushless wound rotor synchronous machines (BL-WRSMs) are one of the alternatives to these PM machines. BL-WRSMs have a lower torque density compared to PM machines. In this paper, a new topology is introduced to improve the torque producing capability of the existing BL-WRSM by utilizing the vacant spaces in the rotor slots. The new topology has two harmonic windings placed on the rotor which induce separate currents. A capacitor is used between the two harmonic windings to bring the currents in phase with each other. The harmonic winding currents are fed to the rectifier which is also placed on the rotor. Due to additional harmonic winding, the overall field current fed to the rotor field winding has been increased and hence the average torque has also increased. Finite element analysis (FEA)-based simulations are performed using ANSYS Maxwell to validate the proposed topology. The results show that the average torque of the machine has been significantly increased compared to the reference model. The detailed comparison results are provided in this paper. [ABSTRACT FROM AUTHOR]

To ensure precise positioning of the macro–micro platform with a symmetrical structure, it is crucial to mitigate the impact of various perturbations, including disturbances, as well as complex factors such as external loads, electrical noise, and model parameter variations. This paper proposes a novel macro–micro master–slave control structure that incorporates adaptive fuzzy linear active disturbance rejection control (AFLADRC). The Kp and Kd parameters of the linear state error feedback (LSEF) are dynamically tuned and adjusted using fuzzy reasoning. This approach enhances the robustness of the system and simplifies the tuning process. In addition, this paper also analyzes the symmetry of the coupling effect between macro and micro, as the coupling will affect the motor force and the reaction potential of the motor. The macro–micro platform adopts a symmetric design; the macro stage is driven by a permanent magnet synchronous linear motor (PMLSM), and the micro stage is driven by a voice coil motor. Finally, we built the macro–micro linear motion experimental platform to verify the control effect of the proposed method by conducting trajectory tracking experiments and comparison experiments. [ABSTRACT FROM AUTHOR]

The challenge of mixing high-viscosity materials is a common issue encountered in the manufacturing process of food materials. The advantages of the internal meshing screw mixer have led to its adoption in various manufacturing processes, but it has yet to be implemented in the food industry. The paper presents a design method for an internal meshing screw mixer based on kinematic principles. The mixer features a helical chamber created by alternating volumes formed by the stator and rotor, establishing an extension-dominated environment for mixing high-viscosity fluids. A kinematic model based on the internal cycloid principle was established, providing trajectories and equations for key points on the rotor, simulating both its rotation and revolution processes, and revealing the velocity variations at different points on the rotor. Based on the kinematic analysis results, a stator and rotor design method was developed according to relevant functional divisions. To achieve the desired motion effects, transmission and support devices were designed, and the relationship between the transmission device and the internal cycloid surface of the fixed rotor was established. The mixer's application and mixing effectiveness in the food industry were validated using corn syrup and flour. Experimental results showed that the extensional mixer described in the paper effectively mixed high-viscosity fluids while also efficiently blending fine powders. Slurry viscosity was tested with a rheometer at different speeds with an eccentric rotor mixer. Results showed that viscosity decreased with increasing shear rate, with a more pronounced decrease at higher shear rates. The apparent viscosity trend remained consistent at different speeds, although variations were observed at lower shear rates, especially concerning speed. The non-Newtonian fluid index exhibited minimal variations at different speeds, while the consistency coefficient showed significant fluctuations. The mixing uniformity index of the slurry was used to evaluate the mixing uniformity and dispersion uniformity of this extensional mixer. At different rotational speeds, the density of the slurry changes little. The uniformity index of mixing decreases gradually with the increase of rotational speed, reaching its maximum at 15 r/min. The overall trend of the uniformity index decreases with increasing rotational speed, indicating a decrease in density uniformity. A peak appears at 45 r/min, possibly due to the maximum values of elongation rate and shear rate at this speed. As the rotational speed increases, the residence time of the material in the mixer decreases, which may be the main reason for the decrease in mixing uniformity. These findings provide valuable insights into the design and utilization of extension-dominated screw mixers within the food industry, laying a solid foundation for future research and practical applications in this field. [ABSTRACT FROM AUTHOR]

The article describes the selection of a permanent magnet synchronous machine design that could be implemented in a small wind turbine designed by the GUST student organization together with researchers working at the Technical University of Lodz. Based on measurements of the characteristics of available machines, eight initial designs of machines with different rotor designs were proposed. The size of the stator, the number of pairs of poles, and the dimensions of the magnets were used as initial parameters of the designed machines. The analysis was carried out about the K-index, the so-called index of benefits. The idea was to make the selected design as efficient as possible while keeping production costs and manufacturing time low. This paper describes how to select the best design of a permanent magnet synchronous generator intended to work with a small wind turbine. All generator parameters were selected keeping in mind the competition requirements, as the designed generator will be used in the author's wind turbine. Based on the determined characteristics of the generator variants and the value of the K-index, a generator with a latent magnet rotor was selected as the best solution. The aforementioned K-index is a proprietary concept developed for the selection of the most suitable generator design. This paper did not use optimization methods; the analysis was only supported by the K-index. [ABSTRACT FROM AUTHOR]

Copyright of Przegląd Elektrotechniczny is the property of Przeglad Elektrotechniczny and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Electric machines emulators (EMEs) based on hardware-in-the-loop (HIL), which effectively act as emulators to mimic the actual motor behavior of Interior Permanent Magnet (IPM) machines. EME is frequently used to evaluate motor controller and motor control methodologies prior to development. The inverse magnetization motor model, which is used as the basis for real-time simulation in this paper's proposal for an electric machine emulator system based on HIL, uses FEA to create the motor model data. The nonlinear features of the motor may be successfully replicated with this motor model, and the accuracy of the electric machine emulator can be enhanced by using a straightforward and trustworthy motor controller. The real-time simulation tool typhoon HIL is used in the study to develop a hardware-in-the-loop simulation platform for an IPM electric machines emulator. [ABSTRACT FROM AUTHOR]

Five‐phase permanent magnet synchronous machine (PMSM) can operate under open‐circuit faults with the appropriate current regulations. However, the traditional current regulations based on the five‐phase half‐bridge inverter have to satisfy the constraint of zero neutral point current, which limits the fault‐tolerant performance of the machine. Thus, this paper investigates the current regulation based on the five‐phase six‐leg (FPSL) inverter, which relieves the zero‐neutral point current limitation, and both current regulations considering the maximum torque (MT) and minimum copper loss (MC) are derived under different open‐circuit conditions. The cost of the system has increased, but with the new regulations, better fault‐tolerant operation capability of the machine can be obtained under all kinds of open‐circuit faults. Moreover, with the introduction of the neutral point current, the machine can work under triple‐phase open‐circuit faults. In conclusion, the proposed control scheme based on the FPSL inverter expands the fault‐tolerant operation capability of the five‐phase PMSM. The experiment results prove the effectiveness of the proposed current regulation on increasing average torque or reducing copper loss under fault‐tolerant operation. [ABSTRACT FROM AUTHOR]

Hybrid switch reluctance motors belong to the family of Switch Reluctance Motors (SRMs) that attenuate magnetic saturation and increase air gap magnetic flux by exploiting permanent magnets. The auxiliary air gap flux generated by permanent magnets can affect the average torque and ripple. Typically, reducing torque ripple results in a decrease in average torque. This paper focuses on reducing torque ripple and enhancing average torque in a 6/10 pole hybrid switch reluctance motor by inserting two symmetrical notches on its rotor. Also, the lengths of the magnet and rectangular notches are optimized using the infinite element method and sensitivity analysis. A comparison between the optimized design and the initial one, conducted through infiniteelement analysis, proves the eficiency of the proposed model. [ABSTRACT FROM AUTHOR]

As the world embarks on a global mission to tackle climate change, reducing carbon represents a key challenge given the escalating global warming. The U.K. is among many other nations that are determined to decarbonise all sectors and strive to achieve a net zero carbon target by 2050. While much attention has been paid to improving performance and reducing carbon emissions in electrical machines, the current research landscape focuses mainly on the thermal and electromagnetic facets. Surprisingly, carbon emissions from the production stage, especially those related to raw material consumption, remain a largely unexplored area. This paper wishes to shed light on a neglected dimension by providing a comprehensive review of carbon emissions in the manufacture of electrical machines, thus contributing significantly to the wider discourse on carbon emission reduction by comparing the carbon emission values associated with various materials commonly used for the main components of these machines. A further case study is included to assess and explore the impact of material alterations on a synchronous machine, from a carbon emission perspective. A reliable material guide will provide engineers at the design stage with the critical insight needed to make informed material selection decisions, highlighting the critical role of carbon emission values beyond conventional thermal and electromagnetic considerations, achieving sustainable and environmentally conscious electrical machine design. [ABSTRACT FROM AUTHOR]

Permanent magnet motors (PMMs) have emerged as key components in numerous industrial applications due to their high efficiency, compact size, and robust performance characteristics. However, to attain optimal performance in PMM drives, accurately predicting and mitigating core losses is paramount. This paper aims to provide a comprehensive review of advancements and methodologies for enhancing the performance of PMM drives by integrating equivalent circuit models (ECMs) that account for core losses. Firstly, the significance of core losses in motor drives is underscored, alongside a survey of research endeavors dedicated to core loss reduction. Notably, emphasis is placed on mathematical models offering both swift computation and reasonable accuracy. Subsequently, the paper delves into the development of ECMs, focusing on approaches adept at capturing core loss effects across diverse operating conditions. Moreover, this paper explores the utilization of these improved ECMs in the design and control of PMMs to achieve enhanced performance. By integrating core loss considerations into design and control strategies, PMM drives can optimize efficiency, torque production, and overall system performance. In summary, this paper may consolidate the current state-of-the-art techniques for enhancing PMM performance through the integration of core-loss-aware ECMs. It highlights key research directions and opportunities for further advancements in this critical area, aiming to foster the development of more efficient and reliable PMM-based systems for a wide range of industrial applications. [ABSTRACT FROM AUTHOR]

Recently, due to the price fluctuation and supply instability of rare earth mineral resources, there has been a lot of development of electric motors using non-rare-earth permanent magnets. As a result, motors using Dy-free permanent magnets and ferrite permanent magnets are being researched, and, in particular, ferrite permanent magnets often utilize spoke-type structures, which are magnetic flux concentrators, to compensate for their low coercivity and residual flux density. However, in general, spoke-type PMSMs do not use much reluctance torque, so double-layer spoke-type PMSMs have been studied for their more efficient design. Unlike general spoke-type PMSMs, double-layer spoke-type PMSMs can utilize high reluctance torque by increasing the difference between d-axis and q-axis reluctance. However, as the difference in magnetic resistance increases, vibration and noise are generated, which adversely affects the mechanical part and shortens the life of the motor. Although this problem seemed to be solved by applying core skew in the previous study, it was confirmed that the axial force caused by the axial leakage flux occurred in the maximum torque per ampere (MTPA) control section and the torque ripple was increased. Therefore, in this paper, a model that can apply symmetrical core skew and reduce axial force is proposed. First, the causes of the axial force generated in previous studies were analyzed. Based on the analysis of these causes, a new symmetrical core skew structure was proposed, and its justification was verified through FEA. [ABSTRACT FROM AUTHOR]

In order to reduce the cogging torque of a symmetrical V-type line-start permanent magnet synchronous (LSPMS) motor, this paper proposes a multi-objective optimization method based on the combination of design parameter stratification and response surface methodology (RSM). The optimal solution to the RSM model is acquired using the max–min ant algorithm. The permanent magnet width, pole opening angle, stator slot width, rotor axial length, and rotor tooth width are selected as optimization variables. The cogging torque and average torque are the optimization objectives. Finite element method (FEM) results show that the cogging torque is reduced by 71.5%, the torque ripple is reduced by 65.6%, and the average torque is improved by 12%. Finally, the effectiveness of the algorithm is verified with simulation results. [ABSTRACT FROM AUTHOR]