Search

To address the problem of late ignition and poor burnout of Foster-Wheeler down-fired boilers, this study proposed a new combustion technology, which combines adding on arch secondary air and alternately arranging the fuel-lean coal/airflow (FLCA) and fuel-rich coal/airflow (FRCA). The coal particle trajectories of FLCA and FRCA and overall aerodynamic characteristics in the furnace were studied at FRCA and FLCA ratio (RRL) of 5:5, 7:3, and 9:1. The results showed that even at a low FRCA ratio, the new combustion technology could still effectively ensure the penetration depth of pulverised coal/airflow. At different RRL values, the main airflow from the arch appeared in the near-wall area and could penetrate downwards into the cold ash hopper area. With an increase in the value of RRL, the deflection degree of FLCA towards the furnace wall increased, while that of FRCA decreased. At RRL of 7:3, both the penetration depth and deflection degree of FRCA and FLCA were at a high level, which was conductive to promoting the burnout and recommended in practical applications. [ABSTRACT FROM AUTHOR]

To effectively control the flow and combustion of pulverised coal in down-fired boilers and improve their thermal efficiency while ensuring low NOx emissions, on arch secondary air (OASA) combustion technology and a smoke-tracing analysis were proposed. The aerodynamic characteristics of a 300-MWe Foster Wheeler (FW) down-fired boiler with the OASA ratios (ROASA) of 0%, 10%, 20%, and 30%, the flow trajectories and mixing characteristics of OASA, and fuel-rich coal/air flow (FRA) and fuel-lean coal/air flow (FLA) were studied experimentally. For the ROASA of <10%, FRA and FLA flow to furnace centre soon after they are injected into the furnace. OASA and FLA may mix with FRA before ignition. For the ROASA of 20% or higher, FRA and FLA flow to the near-wall area soon after being injected into the furnace. FRA mixes with OASA after ignition. With the increase in ROASA, the mixing distance between OASA and FRA increases first and then decreases. The penetration depth of coal/air flow and furnace airflow fullness increases. For the ROASA of 30%, the dimensionless penetration depth of coal/air flow can exceed 0.7. Furnace dimensionless airflow fullness at all the dimensionless heights can exceed 0.6. In real operation, the recommended ROASA is between 20 and 30%. [ABSTRACT FROM AUTHOR]

Number of down-fired boilers burning bituminous coal or anthracite blended with bituminous coal has exceeded 10% of the total down-fired boilers in China. However, lacking of the industrial-scale research on the performance of down-fired boiler burning bituminous coal or blended coal, which limits the actual operation adjustment. Industrial-scale experiments on a 300-MWe down-fired boiler fueled with bituminous coal and blended coal were performed, which boiler was originally designed to burn low-volatile coal. Without the over-fire air, air-staging combustion can still be realized when the down-fired boiler burning bituminous coal. The combustion performance in the down-fired boiler under different coal varieties was compared. Compared with the anthracite case, flue gas temperature is higher, coal flame fullness is greater, O2 consumption occurs faster and NOx concentration is lower in the primary combustion zone when burning bituminous coal. Strong reducing atmosphere is formed in the primary combustion zone. The NOx emissions are low at a level of 410 mg/m3 at 6% O2 at furnace exit and boiler thermal efficiency reaches 92.590% when burning bituminous coal. The NOx emissions cannot be further reduced by burning blended coal. In addition, the boiler thermal efficiency reduced by 1.108%. Without the over-fire air, compared with burning anthracite or lean coal, the NOx emissions and carbon in fly ash significant reduction by 70% and 90%, respectively, and the boiler thermal efficiency increased when burning bituminous coal. [ABSTRACT FROM AUTHOR]

• A novel low-NO x technology is proposed for a down-fired boiler with swirl burners. • Gas/particle flow characteristics are studied under two combustion technologies. • Downward depth of gas/particle flows improves for the improved boiler. • Primary air is effectively ejected by burner secondary air for the novel technology. • Turbulent intensity in the recirculation region increases for the improved boiler. To confirm the validity and progressiveness of the eccentric-swirl-secondary-air combustion technology (ESSACT) in improving the economic and environmental performance of the down-fired boiler (DFB) with swirl burners, the gas/particle (GP) cold-modelling experiments are conducted by using a particle dynamic analyzer (PDA) measurement system in a 1:10 scale model of 300-MW e DFB applying original Babcock & Wilcox combustion technology (BWCT) and novel ESSACT, respectively. The distributions of average velocity, fluctuation velocity and particle size are compared and analyzed under the two combustion technologies in this study, in addition to the decay of particle volume flux and the jet trajectory of downward GP flows. In comparison with the BWCT, the rotation intensity of the burner secondary air is greatly weakened, and the vertical velocities of downward GP flows decay more slowly under the ESSACT. Although the recirculation regions are both formed below the arches under the two combustion technologies, the horizontal velocities and the horizontal fluctuation velocities of GP flows in the recirculation regions are both larger for the ESSACT, which benefits pulverized coal ignition. The particle size distributions under the two combustion technologies reveal that the mixing between the primary air and burner secondary air is obviously delayed and the burner secondary air effectively ejecting the primary air downward is realized by the ESSACT, which is advantageous to improve pulverized coal burnout and inhibit NO x formation. In addition, the maximum particle volume flux in the lower part of the lower furnace under the ESSACT is obviously higher than that under the BWCT, and the downward depth of GP flows and the space utilization ratio in the lower furnace increase for the original BW DFB retrofitted by the ESSACT. [ABSTRACT FROM AUTHOR]

The eccentric-swirl-secondary-air combustion technology has been confirmed to comprehensively solve high NO x emission and poor coal burnout for down-fired boilers with swirl burners. The influence of vent-air inclination angle (β v), a critical factor that affects coal burnout, on gas/particle flow characteristics is investigated to further decrease unburned combustible in fly ash. Gas/particle two-phase flow experiments under different β v (i.e., 10°, 20°, 28°, 40° and 50°) are performed by using a particle dynamic analyser in a 1:10-scale model of the full-scale improved boiler. With increasing β v , the under-arch recirculation zone and the recirculation velocities of gas/particle flows continuously increase. In the staged air region, the vertical velocities of gas/particle flows near water-cooled wall for β v of 40° and 50° are still as high as 2–4 m/s, however, the vertical velocities of gas/particle flows basically decay to negative values for smaller β v of 10° and 20°. At furnace section Y/Y 0 from 0.220 to 0.369, the vertical fluctuation velocities of gas/particle flows near water-cooled wall for β v of 40° and 50° are significantly higher than those with β v of 10°, 20° and 28°, and the particle volume flux at the same horizontal position X/X 0 constantly increases with increasing β v. Furthermore, the downward ejection ability of vent air to gas/particle flows from burners continuously improves, and the downward depth of gas/particle flows and the space utilization ratio of lower furnace both increase with increasing β v. The appropriate inclination angle of vent air for the improved boiler varies from 40° to 50°. Image 1 • A novel high-efficiency low-NO x technology is applied to a down-fired boiler with swirl burners. • Gas/particle flow characteristics at different vent-air inclination angles are investigated. • With increasing angle, recirculation zone and downward depth of gas/particle flows increase. • Primary air is more effectively ejected by under-arch air with increasing inclination angle. • The appropriate inclination angle of vent air for the improved boiler varies from 40° to 50°. [ABSTRACT FROM AUTHOR]

The eccentric-swirl-secondary-air combustion technology (ESSACT) is an innovative technology to comprehensively solve high NO x emission and unburned carbon content in fly ash of the down-fired boiler with swirl burners. In this study, a breakthrough idea (i.e. decreasing burner injection angle (θ b)) is proposed to further greatly improve coal burnout of the improved boiler. Using a laser particle dynamic analyzer, the distributions of average and fluctuation velocities of gas/solid (GS) flows, distribution and decay of particle volume flux and jet trajectory of burner primary air in a 1:10 scale model of full-scale furnace at different θ b of 0°, 8°, 15° and 25° are acquired. The effects of θ b on GS flow characteristics (i.e. downward depth of GS flows, recirculation zones below arches and air flow fullness in the lower furnace) in the furnace are intensively studied. As the θ b decreases, the maximum vertical velocity of GS flows increases in the whole lower furnace, and the vertical fluctuation velocity of GS flows and the turbulent intensity and diffusion also increase. With decreasing θ b , maximum recirculation velocity and dimension of recirculation zone below arches both increase continuously, which is conducive to improving ignition and burnout of pulverized coal. Especially, the maximum recirculation velocity with θ b decreasing from 25° to 15° and the dimension of recirculation zone below arches with θ b decreasing from 15° to 8° increase more obviously. With decreasing θ b , the ejection effects of vent air and staged air on GS flows from arches are more effective. In the region below staged air, the maximum particle volume flux for the θ b of 0° and 8° is more than twice that for the θ b of 15° and 25°. As a result, the downward depth of GS flows and air flow fullness in the lower furnace both increase with decreasing θ b. To improve coal burnout of the down-fired boiler applying ESSACT, the θ b is recommended to be set below 8°. Image 1 • A novel low-NO x technology is proposed for a down-fired boiler with swirl burners. • Gas/particle flow characteristics are studied at various burner injection angles. • Recirculation zone and downward depth of flows both increase with decreasing angle. • Particles are more effectively ejected by vent and staged air with decreasing angle. • The burner injection angle is recommended to be set below 8° for the boiler. [ABSTRACT FROM AUTHOR]

Abstract A new air-staged and low-NO x emission combustion technology has been applied to a 300 MW e anthracite- and down-fired boiler with swirl burners. To achieve the optimum air distribution in the primary combustion zone and further reduce NO x emissions, full-scale industrial experiments varying the ratios between burner secondary air ratio (R bsa) and staged air ratio (R sa) (i.e., R bsa / R sa ratios of 42.9/17.8, 47.1/13.5 and 51.5/9.3), on the premise that the overfire air (OFA) ratio was approximately 20%, were performed to evaluate the overall performance of retrofitted boiler. The improved ignition of coal/air flow was at a distance of 0.8–1.4 m to the burner outlet with increased R bsa / R sa ratio. Compared with the boiler before retrofit, under R bsa / R sa ratios of 47.1/13.5 and 51.5/9.3, the flue gas temperature in the primary combustion zone of the retrofitted boiler increased slightly. Oxygen and carbon monoxide concentrations in the near-sidewall region revealed the furnace flame fullness varied under different R bsa / R sa ratios. With increased the air staged level in the lower furnace, NO x emissions decreased continually and the carbon content in fly ash did not necessarily increased. Under the optimum R bsa / R sa ratio of 47.1/13.5, the NO x reduction efficiency was approximately 46% with increasing boiler thermal efficiency slightly. Highlights • Low-NO x combustion technology was applied to a down-fired boiler with swirl burners. • As NO x emissions increased, carbon content in fly ash did not necessarily decreased. • NO x reduction of 46% was achieved without negative effects at the optimal condition. • Coal ignition and flue gas temperature in the primary combustion zone were improved. • Furnace flame fullness under different operation conditions was revealed. [ABSTRACT FROM AUTHOR]

A 300-MW e anthracite and down-fired boiler equipped with swirl burners, which was retrofitted with the previously proposed deep-air-staging combustion technology to reduce particularly high NO x emissions, still suffered from high carbon content in fly ash (despite this content being slightly lower than that before retrofit) on basis of significant NO x reduction. To comprehensively produce a high-burnout and low-NO x setting, a novel combustion technology was proposed in which relative to the axis of the primary air duct, the axes of the inner and outer secondary air ducts of the swirl burner shift away from the furnace center, and this technology is called an eccentric-swirl-secondary-air combustion technology. The coaxial symmetrical arrangements of primary and secondary air ducts for traditional swirl burners are broken. Full-scale industrial measurements under original, deep-air-staging and eccentric-swirl-secondary-air combustion technologies with respect to different loads (i.e., 180, 250, and 300 MW e ) were carried out to compare and analyze the validity of and improvement offered by the eccentric-swirl-secondary-air combustion technology. Under different boiler loads, especially at low and middle loads, compared with original and deep-air-staging combustion technologies, eccentric-swirl-secondary-air combustion technology markedly extends the penetration depth of coal/air flow and recirculation regions below arches. The thermal resistance between primary coal/air flow and high-temperature flue gas at the furnace center is reduced further, and the ignition of pulverized coal is timelier. The heating gradient in the burner outlet zone is maintained throughout, and the flame fullness in the primary combustion zone increases. The above three aspects contribute to pulverized coal burnout. Similar to deep-air-staging combustion technology, a low-oxygen and strong reducing atmosphere was formed in the primary combustion zone to reduce NO x formation due to the introduction of overfire air. Compared with deep-air-staging combustion technology, for the eccentric-swirl-secondary-air combustion technology, the air staged combustion in the furnace is improved further, and pulverized coal combustion in the primary combustion zone is more well distributed, which is beneficial to further reducing NO x emissions. The results of low-NO x and high-efficiency performance show that compared with the original boiler, NO x emissions and carbon content in fly ash for the boiler with the eccentric-swirl-secondary-air combustion technology are significantly reduced by above 42% and 32.5 to 20.7% at loads of 180, 250 and 300 MW e , respectively. [ABSTRACT FROM AUTHOR]

In consideration of increasing the tertiary air damper opening of a 600 MWe down-fired boiler with prior multiple-injection multiple-staging technology facilitated the coal burnout, while largely increasing the NO x emissions. Additionally, the flame kernel was greatly moved downwards, thus causing significant temperature variations in the hopper near-wall region and the water wall in the lower furnace was vulnerable to overheating. This work concentrated on the comprehensively improved multiple-injection multiple-staging technology, both 1:20 scale cold aerodynamic tests and industrial experiments were conducted to examine the effects of tertiary air damper opening on flow, combustion, NO x emissions and especially the hopper near-wall temperatures. The aerodynamic tests indicated that, on increasing the tertiary air damper opening from 40 to 70%, all the flow fields exhibit good symmetry. The tertiary air flows downwards along the hopper near-wall region, with a maximum near-wall dimensionless vertical velocity significantly increasing from 0.48 to 0.66, and accordingly, the dimensionless depth of downward airflow increases from 0.744 to 0.846. The industrial experimental results showed that, upon introducing more tertiary air, the ignition distance of fuel-rich coal/air flow shortens from 1.25 to 0.87 m. The coal burnout is enhanced, carbon in fly ash drops from 6.90 to 6.15%, while the NO x emissions slightly increase from 593 to 641 mg/m 3 at 6% O 2 . On reducing the measuring height of hopper near-wall temperature from 9.1 to 3.3 m, the average heating rate increases from 0.44 to 0.63 °C/mm. The increased tertiary air damper opening presents an increasingly obvious cooling effect on the hopper near-wall region, with the temperature reductions around 50 °C, which is conductive to protect the water wall in the lower furnace from overheating. [ABSTRACT FROM AUTHOR]

Prior to commercial operation of the first-ever 350-MWe supercritical down-fired boiler incorporating multiple injection and multiple staging combustion technology, cold modeling experiments varying the inner-to-outer-secondary air (ISA/OSA) ratio (applying ratios of 0:10, 2:8, 5:5, 6:4 and 10:0) were performed within a 1:13 scale model of the boiler furnace. The aim of these trials was to establish an optimal inner and outer secondary air distribution model for the burner in the full-scale furnace. At ratios of 0:10 and 2:8, the fuel-rich flow apparently diffused toward the furnace center zone after leaving the corresponding nozzle outlet, resulting in the formation of relatively small recirculation zones below the arches and independent fuel-rich and fuel-lean flow streamlines. In contrast, at ISA/OSA ratios greater than or equal to 5:5, the strengthened carrying effect of the inner secondary air significantly reduced the diffusion of the fuel-rich flow. Consequently, the fuel-rich and fuel-lean flow streamlines combined in the middle region of the lower furnace and the recirculation zones under the arches enlarged. As the ISA/OSA ratio was increased from 0:10 to 10:0, the line fitting slopes for the downward airflow decay curves increased from 1.8 to 3.0, meaning that the downward airflow decayed more rapidly, such that the penetration depth was reduced. Finally, at ISA/OSA ratios of 0:10 and 2:8, the initial flow-field deflection was observed to gradually adopt a symmetrical pattern. [ABSTRACT FROM AUTHOR]

To burn anthracite and reduce NO x emissions, a new combustion system was applied to a 300 MW e Babcock & Wilcox (B&W) down-fired boiler that included overfire air (OFA) and a decreased flow area of the inner and outer secondary air ducts of the installed swirl burners. Industrial-scale measurements (adjusting OFA ratios from 15.4% to 22.6%) were conducted to evaluate the overall performance of the retrofitted boiler. The experimental results demonstrated that the new combustion system promoted coal/air flow ignition and combustion stability. When the OFA ratio was less than 19.7%, the influence of the burner secondary air ratio on coal/air flow ignition was greater than that of the recirculation region below the arches. The overall combustion level in the primary combustion zone depended on the oxygen content and the recirculation region in the lower furnace instead of the early or late ignition of the coal/air flow. Oxygen and carbon monoxide concentration measurements in the near-sidewall region revealed that the fullness degree of the coal flame varied under different OFA ratios. Considering both environmental and economic effects, 19.7% was chosen as the optimal OFA ratio, thereby achieving a significant NO x reduction of 47% without increasing carbon content in the fly ash. [ABSTRACT FROM AUTHOR]

Effects of adjusting the inner-secondary-air damper opening among 100%, 70%, and 50% on the flow, combustion, and NO x emissions of a 600-MWe down-fired boiler incorporating multiple-injection and multiple-staging technology were investigated. Both 1 : 20-scale aerodynamic tests and industrial experiments were conducted. The small-scale tests showed that symmetric flow patterns formed in all cases, and the velocities of boundary and outer secondary air decayed more quickly than the velocity of inner secondary air. As the inner-secondary-air damper opening decreased from 100% to 50%, the average dimensionless depth of downward airflow reduced from 0.830 to 0.788 while the horizontal velocity in the recirculation zone increased. Industrial experiments demonstrated that, as the inner-secondary-air damper opening decreased from 100% to 50%, the heating rate of fuel-rich coal/air flow increased from 572 to 687°C/m, the corresponding ignition distance shortened from 1.36 to 1.11 m, and the hopper near-wall temperature decreased by approximately 50°C. Carbon in fly ash decreased from 7.31% to 6.93%, and NO x emissions rose from 343 to 371 ppm at 6% O2. The boiler efficiency improved from 89.78% to 89.92%. An inner-secondary-air damper opening of 70% is more reasonable than 50% and 100% considering the ignition distance, carbon in fly ash, and NO x emissions. Copyright © 2017 Curtin University of Technology and John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

A new combustion system has been applied to a 300 MW e down-fired boiler with swirl burners to reduce NO x emissions. The unit provided the introduction of overfire air (OFA) and a decrease in the flow area of the inner and outer secondary air ducts of the swirl burners. Industrial experiments on the retrofitted boiler were performed at different loads. Full-scale measurements of the flue gas temperature distribution in the burner outlet region, the furnace temperature distributions measured by a pyrometer and the local mean gas species concentrations in the region near the sidewall were made at loads of 180, 250, and 300 MW e . The results show that the ignition distance increased with decreasing load, especially as the load decreased from 250 MW e to 180 MW e . At three different loads, the retrofitted coal/air flow could be all ignited in time at a distance in the range of 0.6–1.4 m from the burner outlet. Compared with the original combustion system, the ignition distance of the coal/air flow was significantly reduced at a load of 300 MW e . In addition, at a load of 300 MW e , the temperature of the boiler hopper was much higher than that at loads of 180 MW e and 250 MW e . Compared with the original combustion system, the upper furnace temperature decreased slowly with increasing measurement height at a load of 300 MW e after the retrofit. Measurements of the O 2 and CO concentrations in the region near the sidewall indicate that the fullness degree of the coal flame in the furnace at different loads was different. After the retrofit, the reheat steam temperatures reached the design temperature of 541 °C at loads of 180 MW e and 250 MW e , and the average reheat steam temperatures increased by approximately 13 °C. Compared with the original combustion system, a significant NO x reduction (more than 40%) at different loads was achieved without increasing the levels of unburnt carbon in the fly ash. [ABSTRACT FROM AUTHOR]

To achieve significant reductions in NO x emissions without increasing the levels of unburnt carbon in the fly ash, a new combustion system was applied to a 300-MW e Babcock & Wilcox (B&W) down-fired boiler installed with swirl burners. The unit featured introduced overfire air (OFA) and decreased outlet area of the inner and outer secondary-air ducts of the swirl burners. Full-scale measurements (adjusting the inner secondary-air vane angle to 35°, 45°, and 55°) revealed that the influence of the high-temperature recirculating region under the arch upon the combustion and NO x emission characteristics of the boiler is greater than that of the high-temperature flue gas entrained by the swirl burner itself. The ignition distance of the coal/air flow is reduced by at least 1.8 m compared with that of the original combustion system. For the inner secondary-air vane angle of 35°, the coal/air flow ignites earlier than for the vane angles of 45° and 55°. The measurements of the gas species concentrations in the zone near the sidewall indicates that at inspection port 1, the coal flame of the burners does not spread across the entire furnace cross-section for all three vane angles; however, for the vane angle of 35° the flame is spread across the entire furnace cross-section at inspection port 2. For this optimal (35°) inner secondary-air vane angle, the NO x emissions and carbon content in the fly ash reached levels of 674 mg/m 3 (6% O 2 ), and 11.4%, respectively, achieving a significant NO x reduction of 51.9% without increasing the levels of unburnt carbon in the fly ash. [ABSTRACT FROM AUTHOR]

Abstract: An OFA (over-fire air) program and matched measures supporting efficient-combustion are proposed for the FW (Foster Wheeler)-type down-fired boiler, where the OFA is supplied from the arches of the boiler. A gas/solid cold test was conducted at a scale of 1:15, using a two-dimensional laser phase Doppler analyzer to measure parameters in the model furnace, such as the two-phase gas/solid flow velocity, fluctuation velocity, particle size, particle volume flux and particle number concentration. The effects of the OFA ratio on the gas/solid flow characteristics in the furnace were investigated. With an increase in the OFA ratio, the jet depth of the fuel-rich flow decreased. For an OFA ratio of 25%, the jet depth of the fuel-rich flow was much less than that for other OFA ratios, and the residence time of the gas/solid flow in the lower furnace was shorter. An increase in the OFA ratio can increase the penetration depth and allow fuller mixing with the upward airflow, while an OFA ratio that is too great will hinder the upward flow back to the burner nozzle region. An OFA ratio of 20% is considered appropriate for the proposed OFA technical scheme. [Copyright &y& Elsevier]

To overcome the problem of high carbon content in the fly ash of down-fired utility boilers using low-volatility coals, the combustion system of a 660 MWe full-scale down-fired boiler was retrofitted, with the direction of the secondary air under the arch being changed from horizontal to an angle of declination of 20°. Industrial experiments were performed using the boiler before and after the retrofit to determine the reconstruction effect. Data are reported for the gas temperature distribution along the primary air and coal mixture flow, furnace temperature, gas compositions, such as O2, CO, CO2, and NOx, and gas temperatures in the near-wall region. Comparisons between the two cases were made, and the results show that with the angled secondary air under the arches, ignition of the primary air and pulverized coal mixture was brought forward in the boiler. Gas temperatures rose in the fuel-burning zone, and the residence time of pulverized coal in the fuel-burning zone was extended. Thus, the quantity of unburned carbon in fly ash and the gas temperature at the furnace outlet decreased, and the boiler efficiency increased. [ABSTRACT FROM AUTHOR]

Deep peak shaving requires extremely high requirements for low-load combustion stability of boilers. In this study, a novel swirl burner (NSB) with an eccentric secondary air arrangement was proposed, and the validity and the progressiveness of the NSB in achieving ultra-low-load combustion stability for down-fired boilers (DFBs) were confirmed from laboratory experiments to industrial applications. Firstly, the cold-modelling experiments of gas/particle (GP) two-phase flow characteristics involving two combustion systems (i.e., the DFB with traditional swirl burners (TSBs) and the DFB with NSBs) were performed at an ultra-low load of 90 MW e. Compared with the original boiler with TSBs, the maximum horizontal recirculation velocity and the area of recirculation zone below arches significantly increase for the improved DFB with NSBs. The particle number concentration near furnace center for the improved DFB with NSBs is much higher than that for the original DFB with TSBs. The above two aspects will effectively guarantee timely ignition of anthracite. The downward depth of GP flows and the space utilization ratio of the lower furnace increase, which will be beneficial to promoting volume heat load and heat flux density in primary combustion zone. In addition, full-scale industrial-sized measurements aiming at a 300-MW e DFB improved by NSBs were carried out at ultra-low loads of 100 and 90 MW e. For the original DFB after improved by NSBs, the minimum load for stable combustion without oil support is reduced from 150 to 90 MW e , and the ultra-low-load combustion stability is achieved. For the improved DFB with NSBs, pulverized coal ignition distances for operating burners are about 2 and 2.6 m, respectively, and the signal strength of flame detectors for all operating burners is above 95% at 100 and 90 MW e. The flame fullness and combustion stability are good at the initial combustion stage. At ultra-low loads, furnace negative pressure, superheat steam pressure and oxygen concentration at furnace outlet fluctuate slightly. The temperature at air preheater inlet meets the needs of normal operation of denitrification system, and there is no problem of low temperature corrosion on the surface at flue gas side of air preheater. The unburned carbon in fly ash is about 4%. The maximum concentrations of NO x emission at furnace outlet are 714 and 687 mg/m3 (O 2 = 6%) at 100 and 90 MW e , respectively, and ultra-low emission of NO x after denitrification system is achieved. • A novel swirl burner with an eccentric secondary air arrangement was proposed. • Laboratory and industrial experiments were performed. • Performances of flow, mixture, ignition and combustion are all improved. • Ultra-low-load combustion stability is achieved for the improved down-fired boiler. [ABSTRACT FROM AUTHOR]

Numerical simulations are carried out to investigate the influence of burner nozzle–organization–mode (N–O–M) on flow field distribution and combustion characteristics of a 300‐MWe subcritical down‐fired boiler. Three typical N–O–Ms respectively designed with Mitsui Babcock Energy Limited (MBEL), fuel‐lean coal/air flow down‐setting (FD), and multi‐injection multistaging combustion (MIMSC) technology are studied, plus industrial‐size measurements on the original MBEL boiler. Vertical velocity attenuation index (η) and maximum dimensionless penetrating depth (γ) are introduced to estimate the transfer effect and penetrating capacity of pulverized coal/air flow. Results uncover that under the N–O–M based on MBEL technology, flow field and temperature field are deflective. η is 9.257. Under N–O–Ms based on FD and MIMSC technology, flow field and temperature field present obvious symmetry. η respectively are 4.365 and 2.921. γ are correspondingly about 0.8 and 1.36. Carbon content in fly ash and NOx emissions at furnace outlet are lowest (5.77% and 735.21 mg/m3 (O2 = 6%)) under the N–O–M with MIMSC technology. The bigger the η is, the worse penetrating characteristics of coal/air flow is, resulting in poor burnout of pulverized coal. Therefore, MIMSC technology is recommended for the boiler improvement, and η should be taken into account in the design of new down‐fired boiler N–O–Ms. [ABSTRACT FROM AUTHOR]

• Proposed effective low NO x combustion technology with arch-supplied secondary air. • The flow characteristics of the two-phase flows in the furnace were investigated. • Arch-supplied secondary air increases the downward impulse of the two-phase flow. • Increasing arch-supplied secondary air rate can improved the combustion performance. This study proposes a low NO x combustion method for Foster Wheeler type down-fired boilers. The effectiveness of this technique was validated through laboratory-scale gas-particle two-phase experiments and industrial trials. The flow field characteristics within FW-type boiler furnaces equipped with arch-supplied secondary air injection nozzles were investigated. Furthermore, the application of this technique to a 660 MW subcritical FW-type boiler was examined, focusing on NO x emissions and combustion characteristics. Results demonstrate that optimizing the damper openings for F-layer and arch-supplied secondary air can significantly reduce NO x emissions by over 33 %. Additionally, increasing the mass flow rate of arch-supplied secondary air aids in reducing unburned carbon in fly ash and inducing a downward shift in the flame center within the furnace. [ABSTRACT FROM AUTHOR]

A new overfire air (OFA) technology was proposed by the authors for a Foster Wheeler down-fired boiler, and a small-scale cold experimental system for a 660-MWe unit was established. The velocity field distribution was measured in the furnace to study the characteristics of single-phase flow in the furnace at different OFA nozzle angles. The furnace temperature and distributions of the O2 concentration and NO concentration at different OFA nozzle angles were simulated using Fluent 6.3.26, and the average temperature of the furnace outlet, the O2 and NO x concentrations and carbon content in the fly ash were calculated. As the OFA nozzle angle increased, the vertical penetration depth of OFA increased and the horizontal penetration depth of OFA gradually decreased. The carbon content in the fly ash and NO x concentration initially rose and then fell at the furnace outlet, and they were lowest when the OFA angle was set at 20°. Thus, according to the findings of this article, an optimized OFA angle of 20° was chosen. [ABSTRACT FROM AUTHOR]

Abstract: It is necessary to introduce over-fire air (OFA) to a down-fired boiler to lower NO x emission. An appropriate OFA nozzle configuration will reduce the adverse effect of unburnt carbon in fly ash. To investigate mixing behaviors for different OFA angles in down-fired boilers, experiments were carried out on a cold-flow test facility using a particle dynamics anemometer with the main body modeled from a furnace of a down-fired pulverized-coal 300MWe utility boiler. The experiments were carried out for four different OFA nozzle angle settings. For these settings, the distributions of the horizontal and vertical mean velocities and the root mean square velocity fluctuation in the furnace were investigated. The results show that a large OFA nozzle angle results in a shallow horizontal depth reached by the OFA flow in the furnace while a small angle results in a shallow vertical depth reached, both of which are disadvantageous to the final coal burnout. By considering both factors, an optimal angle is selected. [Copyright &y& Elsevier]

Abstract: Industrial experiments were performed with a 300-MWe full-scale down-fired boiler. New data is reported for (i) gas temperature distributions within the primary air and coal mixture flows, (ii) gas compositions, such as O2, CO, CO2 and NO x , and (iii) gas temperatures within the near-wall region. The data complements previously-obtained data from the same utility boiler before being modified by declination of the F-tier secondary air. By directing secondary air under the arches, the region where the primary air and pulverized coal mixture is ignited is brought forward within the boiler. Gas temperatures rose in the fuel-burning zone and fell in the fuel-burnout zone. As a result the quantity of unburned carbon in fly ash and the gas temperature at the furnace outlet were both lowered. [Copyright &y& Elsevier]

Through a gas-particle cold-modeling experiment, the particle dynamic analyzer (PDA) is used to investigate the effects of fuel-lean coal/airflow angle and ratio of oil secondary air to F-layer secondary air on the gas/particle flows characteristics in the furnace of a Foster Wheeler (FW) down-fired boiler with enhanced stable combustion technology. As the fuel-lean coal/airflow angle increases from 10° to 45°, the peak value of the vertical dimensionless velocity of the gas/particle flows gradually increases, and the peak position gradually moves to the near wall region. As the ratio of oil secondary air to F-layer secondary air (the secondary air ratio for short) increased, the peak value of the vertical dimensionless velocity of the gas/particle flows gradually increased and the peak value position of the dimensionless velocity gradually moved towards the near-wall region. In actual operation, for the perspective of performance and safety, the recommended fuel-lean coal/airflow angle and secondary air ratio is 30°and 1:2 respectively. The enhanced stable combustion technology had been applied to two 600 MW FW down-fired boilers, and these boilers can achieve stable operation when burning a wide range of coal quality under the load section from 200 MW to 600 MW. • A Foster Wheeler down-fired boiler retrofitted with novel low-load stable combustion technology is studied by PDA. • Effects of fuel-lean coal/airflow angle and secondary air ratio on the gas/particle flows characteristics were investigated. • The fuel-lean coal/airflow angle of 30° and the secondary air ratio of 1:2 is recommended. • This novel low-load stable down-fired boiler combustion technology is suitable for a wide range of coal quality combustion. [ABSTRACT FROM AUTHOR]

In this paper, based on the MIMSC (multi-injection and multi-stage combustion) technology, new burner arrangement and air distribution parameter settings were proposed for a 300-MW subcritical down-fired boiler originally using MBEL (Mitsui Babcock Energy Limited) combustion technology. Numerical simulations were conducted to study the influences of the secondary-tertiary air proportion on the airflow mixing effect in the furnace, the ignition and pulverized coal combustion characteristics. The airflow mixing effect in the furnace is characterized by the size of the dimensionless vertical velocity decay area (V da) and the fluctuation of the maximum vertical velocity decay curve (V dc). During the research, the sum of the secondary and tertiary air rate remained constant, and the secondary air rate was set to 30.54%, 33.54%, 36.54%, 39.54%, and 42.54%. It was found that under the condition of using new type burner, with the secondary air rate increased from 30.54% to 42.54%, the ignition distance of pulverized coal decreased from 1.30m to 0.84m, the dimensionless penetration depth decreased from 1.46 to 1.27, and the NO x emission and carbon in the fly ash decreased first and then increased. The variation of V dc showed the following regulation. At the secondary air rate of 30.54% to 33.54%, increasing the secondary air rate decreased the fluctuation amplitude. While at the secondary air rate of 39.54% to 42.54%, increasing the secondary air rate increased the fluctuation amplitude. Only at the secondary air rate of 36.54%, V dc in the tertiary air mixing area was smooth. When V dc was smooth, V da was small at 0.043, the carbon in fly ash at the furnace outlet was the lowest at 4.19%, and the NO x emission was low at 675.9 mg/m3 at 6% O 2. An optimal secondary air rate of 36.54% is recommended. For the subsequent design of burner structure and parameters, it is suggested that V dc in the tertiary air mixing area should be smooth. [ABSTRACT FROM AUTHOR]

Fuel rich/lean combustion is an important means of reducing NO x in coal-fired boilers. The mass ratio of pulverized-coal in fuel-rich flow to that in fuel-lean flow (MRL) is a key parameter in fuel rich/lean combustion that affects the gas/particle flow characteristics and in turn the coal ignition and NO x formation. In this work, using a 1:40 scale model furnace and a particle dynamics anemometer measurement system, the effects of various MRLs (6:4, 7:3, 8:2 and 9:1) on the gas/particle flow characteristics in a 600 MWe down-fired boiler incorporating multiple-injection and multiple-staging were studied. The results demonstrate that airflows injected from the front-arch burners flow downwards along the front wall and then turn upward in the furnace center zone, forming a U-shaped flow pattern. Increasing the MRL significantly raises the maximum particle volume flux under the fuel-rich flow nozzle, which favors advanced pulverized-coal ignition and improves the fuel rich/lean combustion in the boiler. The velocity decay of the downward gas/particle flow is also accelerated. The particle volume flux in the hopper zone is gradually reduced while the location of the maximum particle volume flux gradually moves away from the hopper declined wall. This scenario avoids the downward flame flushing the furnace hopper and prevents both hopper wall overheating and tube bursts in the actual down-fired boiler. Based on these results, an MRL of 9:1 is recommended as optimal. [ABSTRACT FROM AUTHOR]

Considering the excessively deep flame depth existing in a 600 MW down-fired boiler incorporating multiple-injection and multiple-staging technology, 1:20 scale aerodynamic tests were conducted to incrementally improve factors responsible for the deep flame depth. These trials demonstrated that, in all cases, the downward velocity near the wing walls decayed more rapidly than that near the furnace center. Increasing the mass ratio of pulverized coal in fuel-rich flow to that in fuel-lean flow and reducing the secondary air ratio while simultaneously increasing the tertiary air ratio was found to increase the penetration depth. Increasing the distance between adjacent burners, optimally lowering the fuel-rich and fuel-lean flow velocities, and reducing the secondary air velocity all decreased the penetration depth. The comprehensively improved downward airflow depth and air flux into the furnace hopper were reduced by 6.3% and 14.9%, respectively. Cold-state airflow tracing tests were performed in an actual boiler, the improved downward airflow depth reduced apparently, which was consistent with the results from modeling tests. Industrial-scale hot-state experiments determined improved hopper near-wall temperatures of 700–800 °C near the furnace center (values that were lower than those of 800–900 °C near the wing walls). These values were approximately 450 °C less than the prior temperatures at the same location, indicating the flame penetration depth was greatly reduced. [ABSTRACT FROM AUTHOR]

• A novel low-load stable combustion technology is applied on a 600MWe FW down-fired boiler. • 33% rated load stable combustion without oil support is achieved. • Full-scale industrial measurements are carried out at 200, 240 and 540MWe. • Combustion and NOx formation characteristics at high and low load are contrastively studied. The randomness and intermittence of solar and wind power generation require coal-fired thermal power boilers that have a low-load stable combustion capacity. This study proposed a novel low-load stable combustion technology in which the oil secondary air flow is arranged parallel to the fuel-rich coal/air flow and participates in pulverised coal combustion during boiler operation. The method was applied to a 600 MWe down-fired boiler manufactured with the technology of Foster Wheeler Corp. Full-scale industrial measurements of furnace flue gas temperature, fuel-rich coal/air flow ignition distance, and distribution characteristics of NOx, O 2 , and CO in the furnace at loads of 200, 240, and 540 MWe were performed. The results showed that the boiler can stably operate without oil support at 240 MWe (40% rated load) and 200 MWe (33% rated load) respectively burning a blended coal of anthracite and lean coal, and blending bituminous coal. At loads of 200, 240, and 540 MWe, the fuel-rich coal/air flow ignition distances were, respectively, approximately 1.4, 1.7, and 1.3 m. NOx emissions at the furnace exit were 406, 407, and 730 mg/Nm3 (O 2 = 6%), and the boiler thermal efficiencies were 92.42%, 92.45%, and 90.58%, respectively. This novel technology presents the characteristics of high efficiency and low NOx emission while realizing low-load stable combustion of down-fired boilers. [ABSTRACT FROM AUTHOR]

Abstract: A new over-fire air (OFA) program, which called arch-supplied OFA, is proposed for Foster Wheeler (FW) type down-fired boiler in this paper. The OFA nozzles are setting on arches near the furnace center and emitting OFA flow into the furnace at an inclined angle. Cold airflow experiments were conducted to determine the effect of the OFA ratio on the aerodynamic field in a small-scale furnace modeled for a 660-MWe down-fired boiler. As the OFA ratio increases, the penetration depth of the OFA flow increases in the level direction and the turning point from downward to upward of the OFA flow moves to the furnace center. At the same time, the velocity of the F-tier airflow decreases and its ability to bring the arch-injected airflow to deeper positions weakens and the turning point from downward to upward of the F-tier airflow moves to the wall. When the OFA ratio is 20%, the OFA flow could penetrate to the furnace center in the level direction and mix with the upflowing gas completely, while the arch-injected airflow have sufficient travel distance and enough residence time in the lower furnace. Thus, considering the penetration depth of arch-injected flow in the vertical direction and the OFA flow in the level direction, an OFA ratio of 20% is recommended for the new OFA arrangement according to the present work. [Copyright &y& Elsevier]

Abstract: Down-fired boilers currently suffer from a number of different issues including high levels of fly ash in the combustible matter, serious slagging and a high level of NO x emissions. In this study, the combustion system of a down-fired 350 MWe supercritical utility boiler was designed with multiple injections and multiple staging to experimentally investigate the impact of the primary air to vent air ratio on the aerodynamic field in the furnace. We constructed a cold 1:10 scale model of the down-fired boiler, and used this to compare the distribution characteristics of the furnace vertical velocity component along the horizontal direction, the decay curves of the downward airflow, and the effect of the secondary air supply ejector on the primary air. It was found that changing the ratio of primary air:vent air had very little effect on the downward flow. Taking the pulverized-coal concentration, the primary air velocity, and other factors into account, we found that the optimal ratio of primary air:vent air was 5:5. [Copyright &y& Elsevier]

Abstract: Using an IFA300 constant temperature anemometer system, cold air experiments on a scale-model of a down-fired pulverized-coal 300MWe utility boiler with swirl burners were performed to investigate the influence of the staged-air flow ratio on flow characteristics in the furnace. This ratio was increased in incremental steps over the range of 7%–20%. The flame reach of the downward airflow was decreased with the ratio increased. A shallower reach is accompanied by a weaker mixing of vent and staged-air. At lower ratios, mixing is good and thus favors coal combustion but weak mixing at intermediate ratios produces a delay in the mixing point. This is compensated by an increasing recirculation zone under the arch that benefits ignition and the appearance of an upward airflow below the mixing point due to an increasing influence of vent air. At higher ratios still, this upward flowing disturbance is centered higher up in the furnace generated primarily by mixing with staged-air as vent-air mixing weakens. [Copyright &y& Elsevier]

Abstract: Industrial experiments were performed for a retrofitted 660MWe full-scale down-fired boiler. Measurements of ignition of the primary air/fuel mixture flow, the gas temperature distribution of the furnace and the gas components in the furnace were conducted at loads of 660, 550 and 330MWe. With decreasing load, the gas temperature decreases and the ignition position of the primary coal/air flow becomes farther along the axis of the fuel-rich pipe in the burner region under the arches. The furnace temperature also decreases with decreasing load, as does the difference between the temperatures in the burning region and the lower position of the burnout region. With decreasing load, the exhaust gas temperature decreases from 129.8°C to 114.3°C, while NO x emissions decrease from 2448 to 1610mg/m3. All three loads result in low carbon content in fly ash and great boiler thermal efficiency higher than 92%. Compared with the case of 660MWe before retrofit, the exhaust gas temperature decreased from 136 to 129.8°C, the carbon content in the fly ash decreased from 9.55% to 2.43% and the boiler efficiency increased from 84.54% to 93.66%. [Copyright &y& Elsevier]

Abstract: Air-surrounding-fuel is a well-known concept used within tangential and wall-fired boilers. Here, we report for the first time on industrial experiments performed to study the effects of this concept on a 660 MWe full-scale down-fired boiler. Data are reported for the gas temperature distributions along the primary air and coal-mixed flows, furnace temperatures, gas compositions, for example O2, CO and NO x , and gas temperatures in the near-wall region. The influence of concentration control valve (CCV) opening on combustion and NO x emission in the furnace were determined. The results show that the flame stability, temperature distribution, unburnt carbon are influenced by both concentration ratios and fuel-rich flow velocities. As CCV opening increases, NO x emissions decrease from 2594 mg/m3 to 1895 mg/m3. Considering altogether economic benefits and environmental protection issues, 30% is the optimal value for the CCV opening. [ABSTRACT FROM AUTHOR]

Abstract: Industrial experiments were performed on a down-fired pulverized-coal 300MWe utility boiler with swirl burners. Gas temperature, concentrations of gas components (O2, CO, CO2 and NO x ) in the burning region and carbon content in the fly ash were measured with outer secondary-air vane angles of 25°, 32.5° and 50°. Results indicate that with increasing vane angle, NO x emission and boiler efficiency decrease. Overall evaluation boiler efficiency and NO x emission, the vane angle of 32.5° is optimum. Using an IFA300 constant-temperature anemometer system, cold air experiments on a quarter-scaled burner model were also carried out to investigate the influence of various outer secondary-air vane angles on the flow characteristics in the burner nozzle region. No central recirculation zone appeared for vane angles of 25° and 32.5°. Most of the pulverized-coal was ignited in the external recirculation zone. For vane angles of 45° and 55°, a central recirculation zone could be observed, and air flow rigidity and axial velocities decreased rapidly. [Copyright &y& Elsevier]

To alleviate the over-temperature of water-wall and increase the energy conversion efficiency of supercritical down-fired boilers, cold-model air/particle flow experiments and in-situ trials were performed to investigate the effects of the secondary-air distribution wall-side deflection coefficient (w s) on air/particle flow and combustion characteristics. As w s increased from 0 to 0.33, the amount of air/particle flow diffused toward water-wall and the corresponding particle concentration both decreased, while the velocity decay was accelerated. At a w s of 0.16, due to prior ignition of fuel-rich flow and a longer flame stroke in lower furnace, the carbon in fly ash and slag were lowest. As w s increased, the thermal load was gradually focused at the furnace center, and the maximum value and deviation of water-wall temperature in lower furnace decreased. Consequently, the temperatures of superheated and reheated steam respectively increased from 542.7 °C to 543.9 °C–560.2 °C and 560.1 °C, respectively. Furthermore, increasing w s from 0 to 0.28 decreased the specific coal consumption from 346.29 to 341.09 g (kW h)−1, indicating the energy conversion efficiency was improved. However, adjusting w s had only a minimal effect on NO x emissions. A w s of 0.28 is recommended to optimize the water-wall temperature, pulverized-coal burnout, and economic performance. [Display omitted] • Laboratory and industrial experiments are combined performed for a down-fired boiler. • The wall-side deflection coefficient of secondary-air distribution (w s) is proposed. • On increasing w s , maximum value and deviation of water-wall temperature is lowered. • Specific coal consumption is reduced and energy conversion efficiency is improved. • The optimum carbon in fly ash and NO x emissions are as low as 4.92% and 654 mg/m3. [ABSTRACT FROM AUTHOR]

Abstract: Experiments with a small-scale cyclone burner used for burner enrichment in a down-fired pulverized-coal 300 MWe utility have been conducted on an air/particle test facility. Particle separating efficiency was obtained with different positions of an adjustable vane. Industrial experiments were performed on a full-scale boiler. The gas temperature distribution along the primary air and coal mixture flow, gas temperature distribution of the furnace, and gas components such as O2, CO, CO2 and NO X in the near-wall region were measured for the first time. The influence of the adjustable vane position on coal combustion in the furnace was determined. With the adjustable vanes at the nozzle, ignition of the primary air and pulverized-coal mixture was delayed and the gas temperature peak was above the burner arch, with high NO X emission. Raising the vanes can bring forward the ignition point but results in the fuel-rich flow being up ahead of time, leading to a rise in carbon content in fly ash and NO X emission. [Copyright &y& Elsevier]

Abstract: Industrial experiments have been performed on a down-fired pulverized-coal 300MWe utility boiler with vent air valve opening of 100% and 40%. The gas temperature distribution along the primary air and coal mixture flow, gas temperature distribution in the furnace, and gas components such as O2, CO, CO2 and NO x in the near-wall region were measured for the first time. The influence of vent air valve opening on coal combustion in the furnace was determined. The results indicate that ignition of the primary air and pulverized-coal mixture is delayed. The position of the gas temperature peak is above the arches. Emission of NO x is up to 2101mg/m3 (at 6% O2 dry) with vent valve opening of 40%. [Copyright &y& Elsevier]