Search

Petioles of non-heading Chinese cabbage are not only an important edible part but also a conduit for nutrient transport, holding significant agricultural and research value. In this study, we conducted a comprehensive genetic analysis of petiole-related traits using a segregating population. Modern quantitative genetic approaches were applied to investigate the genetic regulation of petiole thickness. The results indicated that petiole thickness is a quantitative trait, and the identified genetic model was consistent with two pairs of additive-dominant main genes and additive-dominant polygenes (2MG-AD). BSA-seq analysis identified a major effect of QTL controlling petiole thickness on chromosome A09: 42.08–45.09 Mb, spanning 3.01 Mb, designated as QTL-BrLH9. Utilizing InDel markers, the interval was narrowed down to 51 kb, encompassing 14 genes with annotations for 10 of them. Within the interval, four mutated genes were detected. Combined with gene annotation, protein sequence analysis, and homology alignment, it was found that BraA09g063520.3C's homologous gene SMXL6 in Arabidopsis (Arabidopsis thaliana (L.) Heynh) is an inhibitor of the coding and synthesis of the strigolactone pathway. Strigolactone (SLs) plays an important role in plant growth and development. The cloning results showed that multiple frameshift mutations and non-synonymous mutations occurred on the exon. The qPCR results showed that the expression of the gene was significantly different between the two parents at the adult stage, so it was speculated that it would lead to changes in petiole thickness. BraA09g063520.3C was predicted as the final candidate gene. [ABSTRACT FROM AUTHOR]

At present, there are few studies considering both nonlinear and fractional characteristics of suspension in vehicle systems. In this paper, a fractional nonlinear model of a quarter vehicle with two-degree-of-freedom (2-DOF) is innovatively proposed to describe the suspension system containing the viscoelastic material metal rubber. Given the lack of a general calculation scheme for the multi-degree-of-freedom fractional-order incremental harmonic balance method (IHBM), a general calculation scheme for the 2-DOF incremental harmonic balance method for nonlinear systems with fractional order is derived. The nonlinear dynamical properties of the presented model are acquired using this method. The accuracy of the proposed method is verified through a comparison with the power series expansion method. Afterward, the effects of the various parameters on the dynamic performance are analyzed. The vibration peak value of the fractional-order model is significantly higher than that of the integer-order model (IOM). Therefore, the suspension parameters should be designed with a margin when using IOM. [ABSTRACT FROM AUTHOR]

[Display omitted] Linear piezoelectric materials offer new opportunities for next-generation multifunctional micro/nano systems on chip aside from ferroelectrics. However, the advantage of quantitative pressure sensing of linear piezoelectric materials over ferroelectrics has not been demonstrated, while the thermal stability of linear piezoelectric zinc oxide (ZnO) is yet to be evaluated. In this work, pressure sensors based on linear piezoelectric undoped ZnO and ferroelectric vanadium doped ZnO (V-ZnO) films are studied side by side. Both films possess similar fiber textures oriented along the polar ZnO [0 0 2] direction, yet each of the V-ZnO grains consists of strip-like domains observed by SEM. Applying triangular-wave pressures, the linear piezoelectric ZnO sensor generates triangular-wave voltage signals that are one-to-one linearly correlated to the applied pressure, showing decisive advantages for quantitative pressure sensing compared to the 'sail-like' voltage signals of the ferroelectric V-ZnO sensor that is many-to-one correlated to the applied pressure. Superior thermal stability is demonstrated in the linear piezoelectric ZnO sensor showing stable pressure sensing properties up to 450 °C compared to the degraded sensing properties of the ferroelectric V-ZnO sensor at 150 °C. The thermally stable piezoelectric sensors for quantitative pressure sensing based on linear piezoelectric ZnO films serve as candidates for high-performance multifunctional micro/nano systems. [ABSTRACT FROM AUTHOR]

• The genetic diversity was comprehensively evaluated based on morphological and SSR markers. • 49 out of 66 morphological characteristics presented coefficient of variation (CV) greater than 51%. • Seven main phenotypic components were able to justify 85.17% of total variance. • Growth potential was significantly correlated with flower sex, stigma length, grooves on fruit side, and sepal curl pose characters. • Bud sports, synonymous, and offspring persimmons could be successfully identified by morphological and SSR markers. Persimmon (Diospyros kaki Thunb.) is an economically important fruit crop that originates from China, and has been cultivated for thousands of years. However, the genetic variation remains largely unknown. Evaluation of agronomic traits and genetic diversity in different persimmon germplasm plays an essential role in understanding of the persimmon breeding application and efficient resource utilization. Herein, we carried out the comprehensive evaluation of genetic diversity of persimmon germplasm based on large-scale morphological traits, and SSR markers. A total of 242 accessions were evaluated using 66 phenotypic characteristics and 12 highly polymorphic SSR markers. The results showed that 28 out of 66 descriptive characteristics presented coefficient of variation (CV) greater than 40%, indicating the different accessions of persimmon had rich genetic diversity. Furthermore, it showed varying degrees of correlation among 66 morphological traits. Correlation coefficient analysis present that growth potential was significantly correlated with flower sex, stigma length, grooves on fruit side, and sepal curl pose characters. In addition, we extracted seven components with justifying 85.17% of total variance based on principal component analysis (PCA), and fruit-related traits were the most important variables in distinguishing accessions. Combined cluster analysis based on morphological traits and SSR markers, we identified the four accessions of bud sport, 48 persimmon of synonyms, and two varieties of offspring. This study sheds light on genetic variation of persimmon based on morphological and SSR markers, and provides a valuable resource for marker-assisted breeding of this important fruit crop. [ABSTRACT FROM AUTHOR]

[Display omitted] • We achieved ultrathin epitaxial ZnO thin-film actuators on flexible Hastelloy tapes. • We discovered higher piezoelectric constants in thinner epitaxial ZnO thin films. • We demonstrated tunable linear piezoelectric properties in strained ZnO thin films. Linear piezoelectric materials and devices potentially serve as high-accuracy and fast-response sensors and actuators. However, linear piezoelectrics have been scarcely studied, while tuning the linear piezoelectric response of undoped ZnO remains a challenge. Here, linear piezoelectric zinc oxide (ZnO) thin film actuators are fabricated with a sandwich structure of AZO/ZnO/AZO epitaxially on CeO 2 /Hastelloy substrates, with AZO denoting the aluminum-doped ZnO electrodes and CeO 2 denoting the cerium oxide buffer. Due to the lattice mismatch between ZnO and CeO 2 , compressive in-plane lattice strains are detected. Through varying the ZnO layer thickness, a strong correlation is found between the in-plane epitaxial strain and the piezoelectric constant which proves an effective method to improve the linear piezoelectric response of ZnO. Further, the better linear piezoelectric response of the thinner flexible ZnO layer resolves the controversy between the performance and the deformation-durability of flexible piezoelectric ZnO devices. The vertical piezoelectric constant of the ultrathin (∼32 nm) ZnO film is ∼ 8.14 pm/V, which is highly suitable for positioners working at the picometer scale. Future works harnessing the epitaxial strains to further improve the piezoelectric constant of ZnO materials potentially lead to the prosperity of linear piezoelectrics. [ABSTRACT FROM AUTHOR]

[Display omitted] • We achieved ultrathin flexible AZO electrodes with low resistivities (less than100 μΩ•cm). • We demonstrated the mechanical robustness of ultrathin flexible AZO electrodes. • We discovered abnormally high carrier concentrations in strained epitaxial AZO. Aluminum-doped zinc oxide (AZO) thin films are popular transparent electrodes for optoelectronics and photovoltaics. However, next generation flexible devices demand not only high conductivities but also low thicknesses in AZO electrodes to stay robust against deformations. The two requirements contradict each other due to the scattering of carriers at grain boundaries in polycrystalline AZO electrodes. Herein, this work develops ultrathin, highly conductive, single-crystalline, and mechanically robust AZO electrodes on flexible Hastelloy substrates. The epitaxial growth of AZO on polycrystalline Hastelloy is empowered by an advanced buffer architecture topped with a biaxially-textured MgO layer. Thereby, a c -axis epitaxial strain is generated in the AZO electrodes and then regulated by varying the thickness of the electrodes. Abnormally high carrier concentrations are detected in the AZO electrodes likely caused by the piezopotential generated by the epitaxial strain. While the highest resistivity value of the epitaxial AZO electrodes is within the mainstream values of AZO electrodes on various substrates, a resistivity as low as ~22 μΩ•cm is demonstrated in the ultrathin electrode with a thickness of ~28 nm. The mechanical durability of the ultrathin AZO electrode is validated by bending tests of 1000 cycles. [ABSTRACT FROM AUTHOR]

[Display omitted] • We achieved epitaxial linear-piezoelectric ZnO films on flexible substrates. • We enhanced the linear-piezoelectric constant of ZnO with epitaxial strains. • We proved the trivial impacts of textures on the piezoelectric constant of ZnO. Ferroelectrics are popular for sensors, actuators and transducers. However, the energy barrier for reversing the polarization leads to extra energy losses, while the hysteresis causes phase-lags and non-linearities between input and output signals. The high piezoelectric constants of ferroelectrics dictate the figure-of-merit of piezoelectric devices. Enhancing the piezoelectric constant of linear-piezoelectrics potentially leads to next-generation piezoelectric devices free from issues associated with ferroelectrics. By epitaxial growth of undoped ZnO films on flexible Hastelloy substrates, we demonstrated an ~85% improvement in the piezoelectric constant, and more importantly maintained the linearity of the piezoelectric response. Strong out-of-plane and in-plane crystallographic alignments are detected in the epitaxial sample, yet modeling of the effective thin-film piezoelectric constant shows only a limited contribution of the optimized textures. The improvement in the piezoelectric response is ascribed mostly to the in-plane epitaxial strain resulted from the lattice mismatch of ZnO to the substrate. The epitaxial ZnO film on Hastelloy promisingly offer high-precision positioners with nano-/pico-meter resolutions. Enhancing the piezoelectric constant by strain engineering potentially removes the barrier for applications of linear-piezoelectrics and enriches the piezoelectric research community. [ABSTRACT FROM AUTHOR]

• Simple structure of cube-textured conductive TiN by direct deposition on metal foil. • Ion pre-treatment enables cube texture of TiN directly on polycrystalline substrate. • Ion Beam Assisted Deposition for TiN films with in-plane texture spread of only 5.6°. Single crystal-like titanium nitride (TiN) by ion beam assisted deposition (IBAD) method is a potential conductive and thermally-stable template for growing highly-oriented REBa 2 Cu 3 O 7−x (RE = rare earth) superconductor tapes as well as optoelectronics on flexible metal substrates. Previously, amorphous seed layers such as Al 2 O 3 and Y 2 O 3 were necessary for the biaxially-textured film growth by IBAD. Such nonconductive seed layers prevent an electrically-conductive path between functional film and bottom metal substrate such as flexible, electro-polished Hastelloy (EPH). An approach of Argon ion (Ar+) pre-treatment of EPH surface, followed by roll-to-roll IBAD process has been developed for a simplified architecture of cube-textured TiN directly on flexible metal substrate. Strong cube-textured TiN films with out-of-plane texture spread of 1.8° and in-plane texture spread of 5.6° were obtained by IBAD technique on flexible Hastelloy substrate without any intervening layers; this provides a conductive template for functional layers. Also, the ion pretreatment step is easily achieved in an IBAD system which simplifies the fabrication process. [ABSTRACT FROM AUTHOR]

• Niobium-doped indium oxide (InNbO) was prepared by co-sputtering technique. • InNbO is compact and uniform without obvious pores and cracks. • InNbO is cubic bixbyite polycrystalline structure. • The resistivity of InNbO is as low as 8.29 × 10–3 Ω· cm when the Nb content is 1.8 at%. • InNbO exhibits high optical transmittance from visible to near-infrared wavelength regions. Indium oxide (In 2 O 3) based thin films have attracted much attention due to their high transparency and low resistivity. In order to obtain good transmittance and high conductivity, niobium (Nb) element was chosen as dopant in In 2 O 3 in this study. Nb-doped In 2 O 3 thin films (InNbO) were deposited on substrate by co-sputtering technique. The influence of Nb content on the structural, optical and electrical properties of InNbO thin films was systematically investigated. These thin films are compact and uniform without obvious pores and cracks. And InNbO is cubic bixbyite structure similar to In 2 O 3. When Nb content is 1.8 at%, the resistivity of InNbO is as low as 8.29 × 10−3 Ω·cm. The prepared thin films exhibit high optical transmittance from visible to near-infrared wavelength regions. The average transmittance of InNbO thin films can reach 80.74 % in visible light range (380 ∼ 750 nm), and 75.71 % in near-infrared region (750 ∼ 2400 nm). [ABSTRACT FROM AUTHOR]

This work presents a materially and structurally designed barrier thin film with a self-wrinkling morphology, which consists of composites of amorphous alumina (a-Al 2 O 3) and polycrystalline zinc oxide (ZnO). The pure ZnO, Al 2 O 3 films, and Al 2 O 3 -ZnO composited film are deposited on polyethylene terephthalate (PET) by magnetron co-sputtering at room temperature. The water vapor transmission rate (WVTR) for the composited film with about 30 % ratio of Al 2 O 3 to ZnO is down to 0.026 g·m−2·day−1 from 1.184 g·m−2·day−1 of pure ZnO film at 38 °C/90 % RH, indicating that the nanocomposite structure of amorphous Al 2 O 3 and crystalline ZnO can significantly improve the water-resistance performance. Theoretical calculations demonstrate that the amorphous Al 2 O 3 can dramatically suppress the defect fraction within ZnO from 4.65 % to 0.08 %. Furthermore, a self-wrinkling morphology with Al 2 O 3 -ZnO composited film deposited on PET/acrylic is designed to have the WVTR value as low as 1.30 × 10−3 g·m−2·day−1. Due to the stress release when forming micro-scale wrinkles, the more smooth and dense Al 2 O 3 -ZnO composited film can markedly sharpen up the barrier property. The low WVTR barriers via amorphous and crystalline hybrid composites with self-wrinkling morphology by magnetron sputtering potentially serve as a low-cost and large-scale production path for electronics encapsulation as compared to atomic layer deposition (ALD) and plasma-enhanced chemical vapor deposition (PECVD). [Display omitted] • Al 2 O 3 -ZnO film with an appropriate Al 2 O 3 ratio reduces water vapor transmission rate. • Amorphous Al 2 O 3 -crystalline ZnO hybrid film is deposited by magnetron co-sputtering. • A defect-mediated model for a single film on PET is proposed and applied to the system. • Al 2 O 3 -ZnO film with self-wrinkling morphology markedly sharpens up barrier property. [ABSTRACT FROM AUTHOR]

This work presents a materially and structurally designed barrier thin film with a self-wrinkling morphology, which consists of composites of amorphous alumina (a-Al 2 O 3) and polycrystalline zinc oxide (ZnO). The pure ZnO, Al 2 O 3 films, and Al 2 O 3 -ZnO composited film are deposited on polyethylene terephthalate (PET) by magnetron co-sputtering at room temperature. The water vapor transmission rate (WVTR) for the composited film with about 30 % ratio of Al 2 O 3 to ZnO is down to 0.026 g·m−2·day−1 from 1.184 g·m−2·day−1 of pure ZnO film at 38 °C/90 % RH, indicating that the nanocomposite structure of amorphous Al 2 O 3 and crystalline ZnO can significantly improve the water-resistance performance. Theoretical calculations demonstrate that the amorphous Al 2 O 3 can dramatically suppress the defect fraction within ZnO from 4.65 % to 0.08 %. Furthermore, a self-wrinkling morphology with Al 2 O 3 -ZnO composited film deposited on PET/acrylic is designed to have the WVTR value as low as 1.30 × 10−3 g·m−2·day−1. Due to the stress release when forming micro-scale wrinkles, the more smooth and dense Al 2 O 3 -ZnO composited film can markedly sharpen up the barrier property. The low WVTR barriers via amorphous and crystalline hybrid composites with self-wrinkling morphology by magnetron sputtering potentially serve as a low-cost and large-scale production path for electronics encapsulation as compared to atomic layer deposition (ALD) and plasma-enhanced chemical vapor deposition (PECVD). [Display omitted] • Al 2 O 3 -ZnO film with an appropriate Al 2 O 3 ratio reduces water vapor transmission rate. • Amorphous Al 2 O 3 -crystalline ZnO hybrid film is deposited by magnetron co-sputtering. • A defect-mediated model for a single film on PET is proposed and applied to the system. • Al 2 O 3 -ZnO film with self-wrinkling morphology markedly sharpens up barrier property. [ABSTRACT FROM AUTHOR]