Search

Binder jetting (BJ) 3D printing is especially suitable for the fabrication of an orodispersible solid dosage form, as it is an efficient way to avoid the use of mechanical forces typical for compaction-based processes. However, one of the existing challenges related to pharmaceutical applications of BJ is the relatively high amount of binder needed in the primary powder to ensure the sufficient mechanical strength of printed products. In this study, a strategy based on pre-processing with a thin layer coating was explored. With this strategy, the matrix particles (lactose monohydrate) of the primary powder for BJ 3D printing were coated with the binder (polyvinylpyrrolidone, PVP). The investigated compositions of the primary powder contained PVP at three levels, namely, 10 %, 15% and 20% (w/w). The primary powder compositions were prepared with or without the coated lactose powder, and they were subsequently 3D BJ printed into oral solid products with paracetamol as a model active drug substance. The presence of coated lactose in the primary powder increased the interparticulate interactions in the BJ 3D printed products. Especially for the composition with a relatively small amount of binder (i.e., 10% and 15% w/w PVP in the primary powder), the use of coated particles significantly improved the resistance to crushing and decreased the disintegration time of printed products. In conclusion, thin layer coating is an effective way to pre-process primary powder particles for BJ 3D printing of oral solid products.

Intravenous drugs are often co-administrated in the same intravenous catheter line due to which compatibility issues, such as complex precipitation processes in the catheter line, may occur. A well-known example that led to several neonatal deaths is the precipitation due to co-administration of ceftriaxone- and calcium-containing solutions. The current study is exploring the applicability of Raman spectroscopy for testing intravenous drug compatibility in hospital settings. The precipitation of ceftriaxone calcium was used as a model system and explored in several multi-drug mixtures containing both structurally similar and clinically relevant drugs for co-infusion. Equal molar concentrations of solutions containing ceftriaxone and calcium chloride dihydrate were mixed with solutions of cefotaxime, ampicillin, paracetamol, and metoclopramide. The precipitate formed was collected as an "unknown" material, dried, and analyzed. Several solid-state analytical methods, including X-ray powder diffraction, Raman spectroscopy, and thermogravimetric analysis, were used to characterize the precipitate. Raman microscopy was used to investigate the identity of single sub-visual particles precipitated from a mixture of ceftriaxone, cefotaxime, and calcium chloride. X-ray powder diffraction suggested that the precipitate was partially crystalline; however, the identity of the solid form of the precipitate could not be confirmed with this standard method. Raman spectroscopy combined with multi-variate analyses (principal component analysis and soft independent modelling class analogy) enabled the correct detection and identification of the precipitate as ceftriaxone calcium. Raman microscopy enabled the identification of ceftriaxone calcium single particles of sub-visual size (around 25 μm), which is in the size range that may occlude capillaries. This study indicates that Raman spectroscopy is a promising approach for supporting clinical decisions and especially for compatibility assessments of drug infusions in hospital settings.

Dissolution of solid matter into aqueous solution is one of the most challenging physicochemical aspects related to drug development. While influenced by several parameters, the effect of pH remains the most important one to be fully understood. The dissolution process is essentially controlled by activity at the surface of the molecular crystals, which is difficult to characterize experimentally. To address this, a combination of

Oromucosal administration is an attractive non-invasive route. However, drug absorption is challenged by salivary flow and the mucosa being a significant permeability barrier. The aim of this study was to design and investigate a multi-layered nanofiber-on-foam-on-film (NFF) drug delivery system with unique properties and based on polysaccharides combined as i) mucoadhesive chitosan-based nanofibers, ii) a peptide loaded hydroxypropyl methylcellulose foam, and iii) a saliva-repelling backing film based on ethylcellulose. NFF displays optimal mechanical properties shown by dynamic mechanical analysis, and biocompatibility demonstrated after exposure to a TR146 cell monolayer. Chitosan-based nanofibers provided the NFF with improved mucoadhesion compared to that of the foam alone. After 1 h, >80 % of the peptide desmopressin was released from the NFF. Ex vivo permeation studies across porcine buccal mucosa indicated that NFF improved the permeation of desmopressin compared to a commercial freeze-dried tablet. The findings demonstrate the potential of the NFF as a biocompatible drug delivery system.

Binder jetting (BJ) three-dimensional (3D) printing is becoming an established additive manufacturing technology for manufacturing of solid products for oral drug delivery. Similar to traditional solutions based on compaction of powder mixture, successful processing of BJ products requires control of bulk powder properties. In contrast to traditional compaction-based process, BJ 3D printing allows for flexible modifications on microstructure, material composition and dose in the printed pharmaceutical products. Currently, systematic strategies for selecting excipients and optimizing the printing process have not been fully established. To address this challenge, a summary of the published work and selected patent literature around BJ 3D printing to fabricate pharmaceutical solid products for oral administration purposes is presented. First, an overview of characteristics of printed products as a part of the product design and a description of the commonly used excipients and active pharmaceutical ingredients is given. The critical powder and ink properties, as well as physical geometries and inner structures of a final product, are discussed in term of the mechanisms that determine the formation of a printed solid product and finally the quality of this product. This review is also summarizing the technical features of printers, printheads, and the critical considerations for post-processing procedures. BJ 3D printing is one of the most promising additive manufacturing technologies for mass customization of pharmaceutical products.

Commonly used methods for analyzing tablet disintegration are based on visual observations and can thus be user-dependent. To address this, a generally applicable image analytical algorithm has been developed for machine vision-based quantification of tablet disintegration. The algorithm has been tested with a conventional immediate release tablet, as well as model compacts disintegrating mainly through erosion, and finally, with a polymeric slow-release system. Despite differences in disintegration mechanisms between these compacts, the developed image analytical algorithm demonstrated its general applicability through quantifying the extent of disintegration without adaptation of image analytical parameters. The reproducibility of the approach was estimated with commercial tablets, and further, it could differentiate a range of different model compacts. The developed image analytical algorithm mimics the human decision-making processes and the current experience-based visual evaluation of disintegration time. In doing so the algorithmic method allows a user-independent approach for development of the optimal tablet formulation as well as gaining an understanding on how the selection of excipients and manufacturing processes ultimately influences tablet disintegration.

The pharmaceutical industry is currently implementing new manufacturing principles and modernizing the related processing solutions. A key element in this development is implementation of process analytical technologies (PAT) for measuring product quality in a real-time mode, ideally for a continuously operating processing line. Near-infrared (NIR) spectroscopy is widely used for this purpose, but has limited use for low concentration formulations, due to its inherent detection limit. Light-induced fluorescence (LIF) spectroscopy is a PAT tool that can be used to quantify low concentrations of active pharmaceutical ingredient, and recent development of instrumentation has made it available for in-line applications. In this study, the content of tryptophan in a dynamic powder flow could be measured as low as 0.10 w/w % with LIF spectroscopy with good accuracy of RMSEP = 0.008 w/w %. Both partial least squares regression and support vector machines (SVM) were investigated, but we found SVM to be the better option due to non-linearities between the calibration test and the in-line measurements. With the use of SVM, LIF spectroscopy is a promising candidate for low concentration applications where NIR is not suitable.

CrystEngComm 24(12), 2305 - 2313 (2022). doi:10.1039/D2CE00162D, We demonstrate the ability to controllably desolvate a crystal-solvate system in a step-wise fashion through polymer-assisted grinding by varying the type and proportion of polymer agent used. A plausible mechanistic explanation is proposed based on a combination of experimental evidence and computational analysis. Specifically, Raman spectroscopy, total scattering pair distribution function analysis and computed reaction energies suggest that the desolvation process is associated with preferred interactions between the solvent molecules and specific polymers. This approach could potentially be extended to any type of material, including heat-sensitive materials, where classical desolvation by thermal processes is not possible, and provides an additional route for formulation processing., Published by RSC, London

Additive manufacturing allows for designing innovative properties to pharmaceutical products. Binder jetting (BJ) 3D printing is one of the key techniques within innovative manufacturing. In this study, a structured approach according to the Quality by Design (QbD) principles was implemented to explore the factors affecting fabrication of drug-loaded products produced by BJ 3D printing. The investigated factors included the weight ratio of binder in primary powder and the process parameters related to printing (layer thickness and number of layers). Critical quality attributes, namely disintegration time, tensile strength, friability, dimensions (diameter and height accuracies), residual water content, weight and drug loading were determined based on the quality target product profile of a tablet analogue. The experimental results with a 2-level full factorial design were modeled by multiple linear regression. It was found that binder content was an important factor determining the integrity of the printed products, and the formation of the microstructure of the product was affected by multiple material properties and process parameters. QbD is a systematic and effective approach providing mechanistic understanding of BJ 3D printing and allowing for an efficient design of products with the desired quality.

Additive Manufacturing (AM) comprises a variety of techniques that enable fabrication of customised objects with specific attributes. The versatility of AM procedures and constant technological improvements allow for their application in the development of medicinal products and medical devices. This review provides an overview of AM applications related to respiratory sciences. For this purpose, both fields of research are briefly introduced and the potential benefits of integrating AM to respiratory sciences at different levels of pharmaceutical development are highlighted. Tailored manufacturing of microstructures as a particle design approach in respiratory drug delivery will be discussed. At the dosage form level, we exemplify AM as an important link in the iterative loop of data driven inhaler design, rapid prototyping and in vitro testing. This review also presents the application of bioprinting in the respiratory field for design of biorelevant in vitro cellular models, followed by an overview of AM-related processes in preventive and therapeutic care. Finally, this review discusses future prospects of AM as a component in a digital health environment.

A deep eutectic solvent (DES) is a eutectic system consisting of hydrogen bond donor and acceptor has been suggested as a promising formulation strategy for poorly soluble drugs. A DES consisting of choline chloride and levulinic acid in a 1:2 molar ratio was used to formulate a liquid solution of the model drug aprepitant. This formulation was tested in vitro (drug release and permeability) and in vivo (rat model) and compared with the performance of amorphous aprepitant and the commercial aprepitant nanocrystalline formulation. In this study a DES formulation is compared for the first time directly to other established enabling formulations. The in vitro drug release study demonstrated that the DES formulation and the amorphous form both were able to induce an apparent supersaturation followed by subsequent drug precipitation. To mitigate the risk of precipitation, HPMC was predissolved in the dissolution medium, which successfully reduced the degree of precipitation. In line with the results from the release study, an in vitro permeation study showed superior permeation of the drug from the DES formulation and from the amorphous form compared to the nanocrystalline formulation. However, the promising in vitro findings could not be directly translated into an increased in vivo performance in rats compared to the nanocrystalline formulation. Whilst the DES formulation (34 ± 4%) showed a higher oral bioavailability compared to amorphous aprepitant (20 ± 4%), it was on par with the oral bioavailability obtained from the nanocrystalline formulation (36 ± 2%)., Graphical Abstract Unlabelled Image

Data-enriched edible pharmaceuticals (DEEP) is an approach to obtain personalized medicine, in terms of flexible and precise drug doses, while at the same time containing data, embedded in quick response (QR) codes at a single dosage unit level. The aim of this study was to fabricate DEEP with a patient-tailored dose, modify drug release and design to meet patients’ preferences. It also aimed to investigate physical stability in terms of the readability of QR code patterns of DEEP during storage. Cannabinoids, namely, cannabidiol (CBD) and delta-9-tetrahydrocannabinol (THC), were used as the model active pharmaceutical ingredients (APIs). Three different substrates and two colorants for the ink were tested for their suitability to fabricate DEEP by desktop inkjet printing. Flexible doses and customizable designs of DEEP were obtained by manipulating the digital design of the QR code, particularly, by exploring different pattern types, embedded images and the physical size of the QR code pattern. Modification of the release of both APIs from DEEP was achieved by applying a hydroxypropyl cellulose (HPC) polymer coating. The appearance and readability of uncoated and polymer-coated DEEP did not change on storage in cold and dry conditions, however, the HPC polymer layer was insufficient in preserving the readability of the QR code pattern in the extreme storage condition (40 °C and 75% relative humidity). To sum up, the DEEP concept provides opportunities for the personalization of medicines, considering also patients’ preferences.