Search

This work presents a unique approach to the design, fabrication, and characterization of paper-based origami robotic systems consisting of stackable pneumatic actuators. These paper-based actuators (PBAs) use materials with high elastic modulus-to-mass ratios, accordion-like structures, and direct coupling with pneumatic pressure for extension and bending. The study contributes to the scientific and engineering understanding of foldable components under applied pneumatic pressure by constructing stretchable and flexible structures with intrinsically nonstretchable materials. Experiments showed that a PBA possesses a power-to-mass ratio greater than 80 W/kg, which is more than four times that of human muscle. This work also illustrates the stackability and functionality of PBAs by two prototypes: a parallel manipulator and a legged locomotor. The manipulator consisting of an array of PBAs can bend in a specific direction with the corresponding actuator inflated. In addition, the stacked actuators in the manipulator can rotate in opposite directions to compensate for relative rotation at the ends of each actuator to work in parallel and manipulate the platform. The locomotor rotates the PBAs to apply and release contact between the feet and the ground. Furthermore, a numerical model developed in this work predicts the mechanical performance of these inflatable actuators as a function of dimensional specifications and folding patterns. Overall, we use stacked origami actuators to implement functionalities of manipulation, gripping, and locomotion as conventional robotic systems. Future origami robots made of paper-like materials may be suitable for single use in contaminated or unstructured environments or low-cost educational materials.

Chronic pancreatitis is associated with impaired quality of life, high incidence of comorbidities, serious complications and mortality. Healthcare costs are exorbitant. Some medical societies have developed guidelines for treatment based on scientific evidence, but the gathered level of evidence for any individual topic is usually low and, therefore, recommendations tend to be vague or weak. In the present position papers on chronic pancreatitis from the Societat Catalana de Digestologia and the Societat Catalana de Pàncrees we aimed at providing defined position statements for the clinician based on updated review of published literature and on multidisciplinary expert agreement. The final goal is to propose the use of common terminology and rational diagnostic/therapeutic circuits based on current knowledge. To this end 51 sections related to chronic pancreatitis were reviewed by 21 specialists from 6 different fields to generate 88 statements altogether. Statements were designed to harmonize concepts or delineate recommendations. Part 2 of these paper series discuss topics on treatment and follow-up. The therapeutic approach should include assessment of etiological factors, clinical manifestations and complications. The complexity of these patients advocates for detailed evaluation in multidisciplinary committees where conservative, endoscopic, interventional radiology or surgical options are weighed. Specialized multidisciplinary units of Pancreatology should be constituted. Indications for surgery are refractory pain, local complications, and suspicion of malignancy. Enzyme replacement therapy is indicated if evidence of exocrine insufficiency or after pancreatic surgery. Response should be evaluated by nutritional parameters and assessment of symptoms. A follow-up program should be planned for every patient with chronic pancreatitis. © 2021 Elsevier España, S.L.U.

In recent decades, there has been a growing interest in the recycling of organic materials such as paper mill biosolids (PB) and biochar for use as soil amendments. However, the benefits of co-application of PB and biochar and its effects on soil phosphorus (P) availability remain unknown. An incubation study was conducted on two acidic soils to assess the effect of two PB types (2.5% w/w) co-applied with three rates (0%, 2.5%, and 5% w/w) of pine (Pinus strobus L.) biochar on soil P fractions. An unfertilized control and a mineral NP fertilizer were used as a reference. Soil P fractions were determined by Hedley procedure after 2 and 16 wk of incubation. Material fractionation indicated that the PB containing the highest total P and the lowest Al content had the highest proportion of labile P, whereas most P in the biochar was in a stable form. The incubation study revealed that the P-rich PB increased P availability in both soils to a level comparable to mineral fertilizer at the end of the incubation. The addition of biochar to PB, however, did not affect soil P availability, but the highest rate induced a conversion of P fixed to Al and Fe oxides towards recalcitrant forms, particularly in the sandy loam soil. We conclude that co-applying biochar and PB could be more beneficial than application biochar alone and soils amended with such a mixture would be expected to release part of their P slowly over a longer period of time.

Objective The purpose of this study was to develop a natural language processing (NLP) pipeline to identify incidental thyroid nodules (ITNs) meeting criteria for sonographic follow-up and to assess both adherence rates to white paper recommendations and downstream outcomes related to these incidental findings. Methods 21583 non-contrast chest CT reports from 2017 and 2018 were retrospectively evaluated to identify reports which included either an explicit recommendation for thyroid ultrasound, a description of a nodule ≥ 1.5 cm, or description of a nodule with suspicious features. Reports from 2018 were used to train an NLP algorithm called fastText for automated identification of such reports. Algorithm performance was then evaluated on the 2017 reports. Next, any patient from 2017 with a report meeting criteria for ultrasound follow-up was further evaluated with manual chart review to determine follow-up adherence rates and nodule-related outcomes. Results NLP identified reports with ITNs meeting criteria for sonographic follow-up with an accuracy of 96.5% (95% CI 96.2-96.7) and sensitivity of 92.1% (95% CI 89.8-94.3). In 10006 chest CTs from 2017, ITN follow-up ultrasound was indicated according to white paper criteria in 81 patients (0.8%), explicitly recommended in 46.9% (38/81) of patients, and obtained in less than half of patients in which it was appropriately recommended (17/35, 48.6%). Discussion NLP accurately identified chest CT reports meeting criteria for ITN ultrasound follow-up. Radiologist adherence to white paper guidelines and subsequent referrer adherence to radiologist recommendations showed room for improvement.

The prevalence of diabetes has increased over the past years. Therefore, developing minimally invasive, user-friendly and cost-effective glucose biosensors is necessary especially in low-income and developing countries. Cellulose paper-based analytical devices have attracted the attention of many researchers due to affordability, not requiring trained personnel, and complex equipment. This paper describes a microfluidic paper-based analytical device for the detection of glucose in tear with the naked eye. The paper-based biosensor fabricated by laser CO2, and GOx/HRP enzymatic solution coupled with TMB was utilized as reagents. A sample volume of 10 µl was needed for the biosensor operation and the results were observable within 5 minutes. To evaluate the device performance, color intensity-based and distance-based results were analyzed by ImageJ and Tracker. Distance-based results showed a linear behavior in the range of 0.1–0.6 mM with an R2 = 0.967 and LOD of 0.2 mM. The results could be perceived by the naked eye without any need to further equipment or trained personnel in a relatively short time (3–5 minutes). Moreover, glucose concentration could be obtained non-invasively by tears collected by this µPAD.

Amending croplands with forest residues may help in restoring soil properties in fields subject to intensive land management. Despite their known benefits when applied separately, co-application of wood biochar with paper mill biosolids (PB) has seen little investigation under field conditions. A study was initiated in Québec, QC, Canada, to determine the effect of a single application of wood biochar with and without PB on the nitrogen (N) and phosphorus (P) availability of two pH-neutral to alkaline loamy soils. Biochar at 0, 10, and 20 Mg dry weight·ha−1 and PB at 30 Mg wet weight·ha−1 were applied before planting of corn (Zea mays L.) and soybean [Glycine max (L.) Merr.] in 2018. Residual effect of this co-application was determined under soybean and corn in the subsequent year. In both years, corn received supplemental N and P from mineral fertilizers according to local agronomic recommendations. Co-applying biochar and PB reduced soil NO3-N availability in the year of application and decreased corn yield by 1.0 Mg·ha−1 compared with biochar or PB applied alone, but these amendments did not affect soybean yields. In the following year, the previous biochar addition increased soybean yield by 0.6 Mg·ha−1 but had little effect on corn. For both years, biochar addition induced a large increase in soil Mehlich-3 P. This study revealed that wood biochar positively impacted P status of these soils but was not a source of N to crops even when co-applied with PB.

Acidification and metal mobility may present challenges in soil receiving paper mill biosolids (PB). Co-applying biochar and PB could help prevent these issues, but its effect must be assessed. The objective of this 224 d incubation study was to evaluate the effect of amending two acidic soils, a clay and sandy loam, with two PB types varying in pH (PB1, pH = 7.80; and PB2, pH = 4.51) co-applied with three rates (0%, 2.5%, and 5% w/w) of pine (Pinus strobus L.) biochar on soil pH and macro- (P, K, Ca, and Mg) and micronutrients (Cu, Zn, Fe, and Mn). In both soils, co-applying biochar and PB significantly increased soil pH and extractable K concentration compared with PB-only application, whereas amending with PB significantly increased soil extractable P concentration compared with the unamended soil. In comparison with PB only, co-applying 5% biochar and PB decreased extractable Cu concentration in both soils and extractable Fe concentration in the sandy loam soil. This study showed that co-applying biochar and PB can be more beneficial to agricultural soils than application of PB alone by supplying nutrients and helping prevent metal toxicity by raising pH, especially in acidic sandy soils.

Purpose This study aimed to determine whether continual electronic patient-reported outcome (ePRO) measurements at home can capture the fluctuations in health-related quality of life (HRQOL) scores between visits. Methods We performed a randomized controlled trial to compare the scores obtained by standard practice (paper-based measurements in the hospital) to scores by continuous measurement of ePRO at home. Metastatic cancer patients were randomly assigned to either the paper-based ( n = 50) or the ePRO group ( n = 52). EQ-5D-5L and EORTC QLQ C-30 scores were obtained on 3 different chemotherapy days in the paper-based group. Meanwhile, scores were obtained on the chemotherapy day and on days 3, 7, 10, and 14 in the ePRO group during 2 cycles. The first hypothesis of our study was that both scores at the same time points would be equivalent despite different measurement frequency, place, or mode of measurement. The second hypothesis was that PRO score–adjusted time would be different between the groups. For equivalence, the endpoint was the mean EQ-5D-5L index value on the chemotherapy day before the outpatient treatment. Only if equivalence was shown, quality-adjusted life-days (QALDs) were considered using all the data. Results The adjusted mean difference in the EQ-5D-5L index was determined to be −0.013 (95% confidence interval [CI]: −0.049 to 0.022); the 95% CI did not exceed the equivalence margin. Similarly, the mean difference in global health status (2.28 [95% CI: −2.55 to 7.11]) also showed equivalence. However, the QALD by EQ-5D-5L was significantly lower in the ePRO group by 1.36 per 30 d (95% CI: −2.22 to −0.51; P = 0.0021). Conclusions Continual measurements of the HRQOL at home by ePRO may yield more detailed profiles of the HRQOL.

Background The screening of biological hazards, chemical contaminants and allergens in food products is a major concern of food industry since they can cause serious illnesses and even lead to death. Therefore, there is a significant interest in developing low-cost, robust, and rapid detection methods for food safety and quality analysis. Conventional methods provide accurate analytical characteristics, but require well-equipped laboratories, trained personnel, costly reagents, and complicated sample preparation procedures prior to the detection in order to obtain reliable results. Hence, they are not always ideal for on-site food surveillance. Scope and approach This paper discusses the fundamentals of microfluidic paper-based analytical devices (μPADs) and reviews the recent progress in their usage for screening biological hazards, harmful chemical residues, and allergens in food products to systematically evaluate the strengths and weaknesses of this technology. It then covers future trends and useful strategies that could be employed in μPADs design and fabrication procedures to address the critical challenges in equipment-free food analysis. Key findings and conclusions μPADs offer promising avenues to revolutionize food safety and quality analysis with merits of equipment-free sample preparation and detection at low-cost. Despite the advancement in the microfluidic technology, the manufacturing of user-friendly sample-to-answer μPADs still requires intensive research studies to be employed for robust and sensitive food safety and quality analysis.

Laser-induced graphene (LIG) technology featuring low-cost, high-efficiency and scalability has presented great advantages in micro-supercapacitors (MSCs) fabrication. However, the limited capacitance of LIG based MSCs is still hindering their further development. Herein, we introduce joule heating as a critical in-situ treatment merged with the assembly of laser-induced graphene paper based MSCs (LIGP-MSCs) toward capacitive enhancement. By increasing heating-treatment temperature from ∼20 to 500 °C, the number of nanopores in LIGP continuously increases, attributed to the gradual decomposition of amorphous carbon components. The resulting joule-heated LIGP (J-LIGP) with improved specific surface area (160.97–533.49 m2/g) and pore volume (0.179–0.553 cm3/g) as well as superhydrophilic surface is highly suitable to be employed as J-LIGP-MSCs microelectrodes. By investigating process dependent performance, the J-LIGP-MSCs heated at 500 °C for 60 min delivers a significantly improved specific areal capacitance (CA) of 13.71 mF/cm2 at 10 mV/s, which is approximately six-fold higher than that of unheated LIGP-MSCs. By further exploring and optimizing the process efficiency, J-LIGP-MSCs with a CA of 12.61 mF/cm2 has been achieved by 550 °C heating for only 5 min. Along with superior mechanical flexibility, cyclability and structural modularity, the proposed in-situ joule heating treatment is finally proved to be a universal approach for consistently enhancing the CA of LIG based MSCs processed under various chemical modifications.

Antimicrobial stewardship programs (ASPs) have made immense strides in optimizing antibiotic, antifungal, and antiviral use in clinical settings. However, although ASPs are required institutionally by regulatory agencies in the United States and Canada, they are not mandated for transplant centers or programs specifically. Despite the fact that solid organ transplant recipients in particular are at increased risk of infections from multidrug-resistant organisms, due to host and donor factors and immunosuppressive therapy, there currently are little rigorous data regarding stewardship practices in solid organ transplant populations, and thus, no transplant-specific requirements currently exist. Further complicating matters, transplant patients have a wide range of variability regarding their susceptibility to infection, as factors such as surgery of transplant, intensity of immunosuppression, and presence of drains or catheters in situ may modify the risk of infection. As such, it is not feasible to have a “one-size-fits-all” style of stewardship for this patient population. The objective of this white paper is to identify opportunities, risk factors, and ASP strategies that should be assessed with solid organ transplant recipients to optimize antimicrobial use, while producing an overall improvement in patient outcomes. We hope it may serve as a springboard for development of future guidance and identification of research opportunities.

Mitigation of global warming, energy security and industrial competitiveness urge the energy-intensive pulp and paper industry (PPI) to transform energy use practices. This study investigates how the PPI has responded to the need for the energy transition in the 2000s. Finland and Sweden as forerunners of energy-efficient operation and decarbonization of the PPI are used as target countries. Understanding of changes in energy consumption is complemented using decomposition analysis (Logarithmic Mean Divisia Index Method) and the energy efficiency index approach. Analysis of companies’ investments in energy technologies is used for explaining changes in energy production. Evidence of significant development towards the more sustainable operation of the PPI was found. Energy consumption per produced unit has decreased, i.e., energy efficiency has improved. Fossil fuels have been partially replaced with bio-based alternatives. Thus, the CO2 intensity has decreased substantially. The generation of renewable electricity has increased in both countries. Examples of Finland and Sweden indicate that the PPI has great potential to contribute to CO2 emission reduction worldwide in the future as energy efficiency can be further improved, and the share of fossil fuels can be decreased increasing the use of biofuels and self-generated green electricity at least in kraft pulp mills.

Palliative radiation therapy (pRT) is an effective tool for people with incurable cancer, in the treatment of many cancer-related symptoms such as pain, bleeding and dyspnea. As utilization rates for palliative radiation therapy increase, the demands on the healthcare system continue to grow. Radiation Therapists with advanced knowledge, skills and judgements began demonstrating their ability to practice autonomously in 2004, with the development of the Clinical Specialist Radiation Therapist (CSRT) role. Since this time, CSRTs with a specific focus in pRT (pCSRT) have been increasing in both numbers as well as their positive effects on the cancer care system. Integrating a pCSRT into the existing pRT system has resulted in increased access to and quality of pRT being delivered to palliative cancer patients. The benefits of the addition of pCSRTs to the cancer care system include increasing system capacity and increasing quality of care. This white paper provides information related to the improvements that can be realized in a RT program related to the care and treatment of its palliative patients by adding a pCSRT to the interprofessional healthcare team and suggest it as one of many strategies that can be undertaken to make improvements to access and quality of care.

Poly ( p-phenylene benzoisoxazole; PBO) paper is a potential raw material for use in honeycomb sandwich composites in the aerospace industry, which are able to sustain high temperatures exceeding 300°C. This work presents a wet-forming method of making PBO paper, consisting of PBO chopped fibers. The paper was impregnated with phenolic resin to simulate honeycomb wall material. The structure and mechanical and dynamic mechanical properties of the raw and impregnated paper were characterized. The performance of PBO paper was tested against p-aramid paper. The comparative results showed the tensile strength of PBO raw paper was 2.17 kN/m, which was slightly worse than p-aramid raw paper: 2.66 kN/m. After impregnation, the tensile strength of the PBO paper was 13.93 kN/m due to the increase in the number of bonding points—better than p-aramid paper: 7.99 kN/m. The tearing resistance value for PBO raw paper versus p-aramid raw paper was 3252 mN against 845 mN. The morphology of the torn samples in the impregnated paper revealed higher levels of PBO fiber pullout than p-aramid fiber, therefore the tearing resistance value was 6000 mN for PBO impregnated paper, which was again superior to p-aramid impregnated paper: 675 mN. The PBO paper also showed higher storage modulus than p-aramid paper after impregnation. Experimental studies showed that PBO paper could be used in load-bearing structures and in honeycomb components where high resistance to deformation and thermal stability is necessary.

Purpose In flexible electronics applications, organic inks are mostly used for inkjet printing. Three-dimensional (3 D) printing technology has the advantages of low cost, high speed and good precision in modern electronic printing. The purpose of this study is to solve the high cost of traditional printing and the pollution emissions of organic ink. It is necessary to develop a water-based conductive ink that is easily degradable and can be 3 D printed. A nano-silver ink printed circuit pattern with high precision, high conductivity and good mechanical properties is a promising strategy. Design/methodology/approach The researched nano-silver conductive ink is mainly composed of silver nanoparticles and resin. The effect of adding methyl cellulose on the ink was also explored. A simple 3 D circuit pattern was printed on photographic paper. The line width, line length, line thickness and conductivity of the printed circuit were tested. The influence of sintering temperature and sintering time on pattern resistivity was studied. The relationship between circuit pattern bending performance and electrical conductivity is analyzed. Findings The experimental results show that the ink has the characteristics of low silver content and good environmental protection effect. The printing feasibility of 3 D printing circuit patterns on paper substrates was confirmed. The best printing temperature is 160°C–180°C, and the best sintering time is 30 min. The circuit pattern can be folded 120°, and the cycle is folded more than 60 times. The minimum resistivity of the circuit pattern is 6.07 µΩ·cm. Methyl cellulose can control the viscosity of the ink. The mechanical properties of the pattern have been improved. The printing method of 3 D printing can significantly reduce the sintering time and temperature of the conductive ink. These findings may provide innovation for the flexible electronics industry and pave the way for alternatives to cost-effective solutions. Originality/value In this study, direct ink writing technology was used to print circuit patterns on paper substrates. This process is simple and convenient and can control the thickness of the ink layer. The ink material is nonpolluting to the environment. Nano-silver ink has suitable viscosity and pH value. It can meet the requirements of pneumatic 3 D printers. The method has the characteristics of simple process, fast forming, low cost and high environmental friendliness.

The pulp and paper industry is highly energy-intensive. In mills that use chemical pulping, roughly half of the higher heating value of the cellulosic material used to manufacture the product typically is incinerated to generate steam and electricity that is needed to run the processes. Additional energy, much of it non-renewable, needs to be purchased. This review considers publications describing steps that pulp and paper facilities can take to operate more efficiently. Savings can be achieved, for instance, by minimizing unnecessary losses in exergy, which can be defined as the energy content relative to a standard ambient condition. Throughout the long series of unit operations comprising the conversion of wood material to sheets of paper, there are large opportunities to more closely approach a hypothetical ideal performance by following established best-practices.

Aβ42 is one of the most extensively studied blood and Cerebrospinal fluid (CSF) biomarkers for the diagnosis of symptomatic and prodromal Alzheimer’s disease (AD). Because of the heterogeneity and transient nature of Aβ42 oligomers (Aβ42Os), the development of technologies for dynamically detecting changes in the blood or CSF levels of Aβ42 monomers (Aβ42Ms) and Aβ42Os is essential for the accurate diagnosis of AD. The currently commonly used Aβ42 ELISA test kits usually mis-detected the elevated Aβ42Os, leading to incomplete analysis and underestimation of soluble Aβ42, resulting in a comprised performance in AD diagnosis. Herein, we developed a dual-target lateral flow immunoassay (dLFI) using anti-Aβ42 monoclonal antibodies 1F12 and 2C6 for the rapid and point-of-care detection of Aβ42Ms and Aβ42Os in blood samples within 30 min for AD diagnosis. By naked eye observation, the visual detection limit of Aβ42Ms or/and Aβ42Os in dLFI was 154 pg/mL. The test results for dLFI were similar to those observed in the enzyme-linked immunosorbent assay (ELISA). Therefore, this paper-based dLFI provides a practical and rapid method for the on-site detection of two biomarkers in blood or CSF samples without the need for additional expertise or equipment. Graphical Abstract

Neonatal and infantile cholestasis (NIC) can represent the onset of a surgically correctable disease and of a genetic or metabolic disorder worthy of medical treatment. Timely recognition of NIC and identification of the underlying etiology are paramount to improve outcomes. Upon invitation by the Italian National Institute of Health (ISS), an expert working grouped was formed to formulate evidence-based positions on current knowledge about the diagnosis of NIC. A systematic literature search was conducted to collect evidence about epidemiology, etiology, clinical aspects and accuracy of available diagnostic tests in NIC. Evidence was scored using the GRADE system. All recommendations were approved by a panel of experts upon agreement of at least 75% of the members. The final document was approved by all the panel components. This position document summarizes the collected statements and defines the best-evidence diagnostic approach to cholestasis in the first year of life.

Lean manufacturing (LM) is established as a best practice to improve the performance of manufacturing industries. Not all the manufacturing industries realize the benefits of LM practices specifically continuous process industries. The present research work is intended to study the advantages of implementing LM practices in an ethical paper industry which is a continuous production industry. Presently, the industry suffers with the problems such as lack of productivity, raw material wastes, underutilized resources, and lack of standard practices in the production. Gemba technique is adapted to record the information related to the present manufacturing environment. Based on the current state analysis, the feasible lean tools are selected and implemented such as 5S, Kaizen, and Total Productive Maintenance (TPM). The improvements have been noted as reduced tool change over time, reduced material wastes, effective utilization of resources and provide safety guidelines to workers and operations. The implications of these improvements increased the productivity also.

Malnutrition, muscle loss, and cachexia are prevalent in cancer and remain key challenges in oncology today. These conditions are frequently underrecognized and undertreated and have devastating consequences for patients. Early nutrition screening/assessment and intervention are associated with improved patient outcomes. As a multifaceted disease, cancer requires multimodal care that integrates supportive interventions, specifically nutrition and exercise, to improve nutrient intake, muscle mass, physical functioning, quality of life, and treatment outcomes. An integrated team of healthcare providers that incorporates societies’ recommendations into clinical practice can help achieve the best possible outcomes. A multidisciplinary panel of experts in oncology, nutrition, exercise, and medicine participated in a 2-day virtual roundtable in October 2020 to discuss gaps and opportunities in oncology nutrition, alone and in combination with exercise, relative to current evidence and international societies’ recommendations. The panel recommended five principles to optimize clinical oncology practice: (1) position oncology nutrition at the center of multidisciplinary care; (2) partner with colleagues and administrators to integrate a nutrition care process into the multidisciplinary cancer care approach; (3) screen all patients for malnutrition risk at diagnosis and regularly throughout treatment; (4) combine exercise and nutrition interventions before (e.g., prehabilitation), during, and after treatment as oncology standard of care to optimize nutrition status and muscle mass; and (5) incorporate a patient-centered approach into multidisciplinary care.

Herein, paper mill waste sludge (PMS) from two different sources has been investigated to extract calcium hydroxide, Ca(OH)2 by a facile and inexpensive extraction process. This green process exploits typical chemical precipitation (CP) in an aqueous medium at room temperature to develop an economically and industrially viable technique for the effective utilization of calcium-containing waste sludge. PMS samples, collected from local paper mill plants of Bangladesh, were the main precursors wherein HCl and NaOH were utilized for chemical treatment. The as-synthesized products were analyzed by a variety of characterization tools including X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, Scanning electron microscopy (SEM), and Energy Dispersive X-ray (EDX) elemental analyses. Our studies confirm that the extracted product contains Ca(OH)2 as a major content, albeit it also includes CaCO3 phase formed owing to the inescapable carbonation process from the surrounding environment. The particle size of the synthesized products is in the range of 450 - 500 nm estimated from SEM micrographs. The crystallite domain size of the same estimated from XRD analyses and was found to be ~47 nm and ~31 nm respectively for product-A and product-B considering major (101) Bragg peak of Ca(OH)2. The yield percentage of the isolated products is about 65% for samples collected from both sources.

With the development of printed electronics technology, the demand for printed conductive inks had also put forward higher standards. The shortcomings of traditional printed circuit boards, such as complex technology, consumables, and pollution, had also been resolved with the development of 3D printing technology. In this paper, low-content silver nanoparticles were blended with graphene alcohol slurry and dissolved in a non-polluting solvent such as absolute ethanol. The synergistic effect of the composite of the hexagonal structure of the graphene sheet and the silver nanoparticles improved the ink’s performance of electrical conductivity, adding water-based polyurethane/acrylic resin system to improve the adhesion between ink and paper. The conductive ink can be used to 3D print circuit circuits on paper. After drying, the resistance was measured. After the battery, diode, and switch were connected, a circuit diagram was made. After pressing the diode emits was lighted. This work is expected to be applied to flexible circuit boards to provide basic research.

This White Paper by the European Society for Swallowing Disorders (ESSD) reports on the current state of screening and non-instrumental assessment for dysphagia in adults. An overview is provided on the measures that are available, and how to select screening tools and assessments. Emphasis is placed on different types of screening, patient-reported measures, assessment of anatomy and physiology of the swallowing act, and clinical swallowing evaluation. Many screening and non-instrumental assessments are available for evaluating dysphagia in adults; however, their use may not be warranted due to poor diagnostic performance or lacking robust psychometric properties. This white paper provides recommendations on how to select best evidence-based screening tools and non-instrumental assessments for use in clinical practice targeting different constructs, target populations and respondents, based on criteria for diagnostic performance, psychometric properties (reliability, validity, and responsiveness), and feasibility. In addition, gaps in research that need to be addressed in future studies are discussed. The following recommendations are made: (1) discontinue the use of non-validated dysphagia screening tools and assessments; (2) implement screening using tools that have optimal diagnostic performance in selected populations that are at risk of dysphagia, such as stroke patients, frail older persons, patients with progressive neurological diseases, persons with cerebral palsy, and patients with head and neck cancer; (3) implement measures that demonstrate robust psychometric properties; and (4) provide quality training in dysphagia screening and assessment to all clinicians involved in the care and management of persons with dysphagia.

Background/Aims: The incidence of disease outbreaks in clinical settings arising from ultrasound examinations is well documented, and is a source of worry. The ultrasound transducers and the coupling gel are potential sources of these infections since they come in direct contact with the patient’s skin. In this study, we examine the efficacy of the widespread practice of the use of plain non-sterile tissue paper in some low-cost private ultrasound centres in our locality as a method of disinfecting ultrasound transducers after each use. Its potential impact on nosocomial infection management in clinical practice is also examined. Methods: Swab samples from convex ultrasound transducers before and after transabdominal scanning of three consecutive patients were obtained from 10 different ultrasound centres in urban and rural areas of Enugu state. Ultrasound coupling gel samples were equally obtained, and all samples cultured for bacteria growth which was quantified in colony-forming units per ml (CFU/ml) and reported in 1000/ml. Paired sampled t-test was used to check for significance in a reduction in a bacterial load before and after the transducer was cleaned. Results: Nine different bacterial strains were isolated. Staphylococcus aureus and Klebsiella spp had the highest percentage of occurrence in all centres. Significant bacteria growth was recorded in the morning before the examination, and plain tissue paper significantly reduced the bacteria load in the ultrasound transducer. Conclusion: Even though disinfecting ultrasound transducers with non-sterile plain tissue paper alone is statistically effective and has the potential to minimize nosocomial infection, it is however not clinically effective and hence not advised.

Refereed/Peer-reviewed At a paper manufacturing mill (PML) that had been previously part of an integrated pulp (bisulphite) and paper mills industry, cyanobacterial blooms were observed in the mill’s aerated stabilization basin (ASB) ponds at about 3 years after pulping had been discontinued. This study aimed to determine the factors that led to bloom occurrences and potential control strategies applicable to the paper manufacturing mill’s, aerated stabilization basin system that discharges wastewaters into a coastal lake. Following discontinuation of pulping, the colour of the wastewaters reduced to low levels (~ 10 Hazen units or less), while the levels of nutrient remained potentially supportive of cyanobacteria growth with total phosphorus at ~ 0.1 mg/L and total nitrogen at > 2.5 mg/L. Incidences of blooms in the ABS were associated with preceding average monthly rainfalls and wind speeds being less (~ 44% and ~ 7%, respectively) and average direct sunlight hours being greater (~ 9%) than the long-term average values. Zinc was investigated for control of cyanobacteria as this metal is less toxic to aquatic organisms and microflora than copper algaecides. In laboratory culture trials, zinc was found to inhibit growth of M. aeruginosa (strain MIC338) and Pseudanabaena sp. when dosed at ~ 2.5 mg/L. The inhibition of cyanobacteria by zinc was found to vary between ASB pond samples which had different in situ chlorophyll a levels. This study found that the PML wastewaters investigated can be supportive of cyanobacterial growth to bloom levels after discontinuation of pulping processes and that zinc has potential as a cyanobacteria control agent.

[Abstract] The accepted use of left ventricular assist device (LVAD) technology as a good alternative for the treatment of patients with advanced heart failure together with the improved survival of the LVAD-supported patients on the device and the scarcity of donor hearts has significantly increased the population of LVAD-supported patients. The expected and non-expected device-related and patient-device interaction complications impose a significant burden on the medical system exceeding the capacity of the LVAD implanting centres. The ageing of the LVAD-supported patients, mainly those supported with the 'destination therapy' indication, increases the risk for those patients to experience comorbidities common in the older population. The probability of an LVAD-supported patient presenting with medical emergency to a local emergency department, internal, or surgical ward of a non-LVAD implanting centre is increasing. The purpose of this trilogy is to supply the immediate tools needed by the non-LVAD specialized physician: ambulance clinicians, emergency ward physicians, general cardiologists, internists, anaesthesiologists, and surgeons, to comply with the medical needs of this fast-growing population of LVAD-supported patients. The different issues discussed will follow the patient's pathway from the ambulance to the emergency department and from the emergency department to the internal or surgical wards and eventually to the discharge home from the hospital back to the general practitioner. In this first part of the trilogy on the management of LVAD-supported patients for the non-LVAD specialist healthcare provider, after the introduction on the assist devices technology in general, definitions and structured approach to the assessment of the LVAD-supported patient in the ambulance and emergency department is presented including cardiopulmonary resuscitation for LVAD-supported patients.

The possibility of exfoliating graphite into graphene sheets allows the researchers to produce a material, termed "graphene paper" (G-paper), conductive as graphite but more flexible and processable. G-paper is already used for electronic applications, like conductors, antennas, and heaters, outperforming metal conductors thanks to its high flexibility, lightness, chemical stability, and compatibility with polymeric substrates. Here, the effectiveness in the use of G-paper for the realization of electrodes on flexible plastic substrates and textiles, and their applicability as amperometric sensors are demonstrated. The performance of these devices is compared with commercial platforms made of carbon-based inks, finding that they outperform commercial devices in sensing nicotinamide adenine dinucleotide (NADH), a key molecule for enzymatic biosensing; the electrodes can achieve state-of-the-art sensitivity (107.2 ?A mm cm) and limit of detection (0.6 × 10 m) with no need of additional functionalization. Thanks to this property, the stable deposition of a suitable enzyme, namely lactate dehydrogenase, on the electrode surface is used as a proof of concept of the applicability of this new platform for the realization of a biosensor. The possibility of having a single material suitable for antennas, electronics, and now sensing opens new opportunities for smart fabrics in wearable electronic applications.

The Veterans Health Administration (VHA) is the United States' largest integrated health care delivery system, serving over 9 million enrollees at nearly 1300 health care facilities. In addition to providing health care to the nation's military veterans, the VHA has a research and development program, trains thousands of medical residents and other health care professionals, and conducts emergency preparedness and response activities. The VHA has been celebrated for delivering high-quality care to veterans, early adoption of electronic medical records, and high patient satisfaction. However, the system faces challenges, including implementation of an expanded community care program, modernization of its electronic medical records system, and providing care to a population with complex needs. The position paper offers policy recommendations on VHA funding, the community care program, medical and health care professions training, and research and development.

Background: The cost-effectiveness of using a mobile diary app as an adjunct in dialectical behavior therapy (DBT) in patientswith borderline personality disorder is unknown.Objective: This study aims to perform an economic evaluation of a mobile diary app compared with paper-based diary cardsin DBT treatment for patients with borderline personality disorder in a psychiatric outpatient facility.Methods: This study was conducted alongside a pragmatic, multicenter, randomized controlled trial. The participants wererecruited at 5 Danish psychiatric outpatient facilities and were randomized to register the emotions, urges, and skills used in amobile diary app or on paper-based diary cards. The participants in both groups received DBT delivered by the therapists. Acost-consequence analysis with a time horizon of 12 months was performed. Consequences included quality-adjusted life years(QALYs), depression severity, borderline severity, suicidal behavior, health care use, treatment compliance, and system usability.All relevant costs were included. Focus group interviews were conducted with patients, therapists, researchers, and industryrepresentatives to discuss the potential advantages and disadvantages of using a mobile diary app.Results: A total of 78 participants were included in the analysis. An insignificantly higher number of participants in the papergroup dropped out before the start of treatment (P=.07). Of those starting treatment, participants in the app group had an averageof 37.1 (SE 27.55) more days of treatment and recorded an average of 3.16 (SE 5.10) more skills per week than participants inthe paper group. Participants in both groups had a QALY gain and a decrease in depression severity, borderline severity, andsuicidal behavior. Significant differences were found in favor of the paper group for both QALY gain (adjusted difference −0.054;SE 0.03) and reduction in depression severity (adjusted difference −1.11; SE 1.57). The between-group difference in total costsranged from US $107.37 to US $322.10 per participant during the 12 months. The use of services in the health care sector wassimilar across both time points and groups (difference: psychiatric hospitalization and 2.02; SE 3.19). Overall, the patients showed high acceptability and considered the app as being easy to use. Therapists worriedabout potential negative influences on the therapist-patient interaction from new work tasks accompanying the introduction ofthe new technology but pointed at innovation potential from digital database registrations.Conclusions: This study suggests both positive and negative consequences of mobile diary apps as adjuncts to DBT comparedwith paper diary cards. More research is needed to draw conclusions regarding its cost-effectiveness. Background:The cost-effectiveness of using a mobile diary app as an adjunct in dialectical behavior therapy (DBT) in patients with borderline personality disorder is unknown.Objective:This study aims to perform an economic evaluation of a mobile diary app compared with paper-based diary cards in DBT treatment for patients with borderline personality disorder in a psychiatric outpatient facility.Methods:This study was conducted alongside a pragmatic, multicenter, randomized controlled trial. The participants were recruited at 5 Danish psychiatric outpatient facilities and were randomized to register the emotions, urges, and skills used in a mobile diary app or on paper-based diary cards. The participants in both groups received DBT delivered by the therapists. A cost-consequence analysis with a time horizon of 12 months was performed. Consequences included quality-adjusted life years (QALYs), depression severity, borderline severity, suicidal behavior, health care use, treatment compliance, and system usability. All relevant costs were included. Focus group interviews were conducted with patients, therapists, researchers, and industry representatives to discuss the potential advantages and disadvantages of using a mobile diary app.Results:A total of 78 participants were included in the analysis. An insignificantly higher number of participants in the paper group dropped out before the start of treatment (P=.07). Of those starting treatment, participants in the app group had an average of 37.1 (SE 27.55) more days of treatment and recorded an average of 3.16 (SE 5.10) more skills per week than participants in the paper group. Participants in both groups had a QALY gain and a decrease in depression severity, borderline severity, and suicidal behavior. Significant differences were found in favor of the paper group for both QALY gain (adjusted difference −0.054; SE 0.03) and reduction in depression severity (adjusted difference −1.11; SE 1.57). The between-group difference in total costs ranged from US $107.37 to US $322.10 per participant during the 12 months. The use of services in the health care sector was similar across both time points and groups (difference: psychiatric hospitalization Conclusions:This study suggests both positive and negative consequences of mobile diary apps as adjuncts to DBT compared with paper diary cards. More research is needed to draw conclusions regarding its cost-effectiveness.

The contamination of water and food in agricultural areas, where an enormous volume of pesticides is widely employed to enhance crop production, is a challenging reality. The rapid assessment of these contaminants is fundamental to assure water and food quality and safety, particularly for local community members. This work presents a nonexpensive and easy-operational paper-based testing device for the fast detection of insecticides (carbamates and organophosphates) in water samples. The structural design "dip-and-fold" allows us to carry out the analysis without introducing reagents or samples. The device is prepared using different high-quality papers to support the active acetylcholinesterase (AChE) and the customized chemical formulation for colorimetric detection. The chemical principle is based on the AChE inhibition reaction and Ellman's method. The experiments using standard solutions of carbofuran, propoxur, and chlorpyriphos indicated satisfactory detection at concentrations between 0.1 and 0.0001 mM, and the color results are revealed within 10 min. Therefore, this technique represents a promising alternative for implementing low-cost and efficient water monitoring and management solutions.

Around 60% of the paper worldwide is made from recovered paper. Especially adhesive contaminants, so called stickies, reduce paper quality. To remove stickies but at the same time keep as many valuable fibers as possible, multi-stage screening systems with several interconnected pressure screens are used. When planning such systems, suitable screens have to be selected and their interconnection as well as operational parameters have to be defined considering multiple conflicting objectives. In this contribution, we present a Mixed-Integer Nonlinear Program to optimize system layout, component selection and operation to find a suitable trade-off between output quality and yield.

Introduction Muscular dystrophies present a group of inherited degenerative disorder that are characterized by progressive muscular weakness. This evidence-based position paper represents the official position of the European Union through the UEMS PRM Section. The aim of the paper is to evaluate the role of the physical and rehabilitation medicine (PRM) physician and PRM practice for people with muscular dystrophies. Evidence acquisition A systematic review of the literature and a consensus procedure by means of a Delphi process have been performed involving the delegates of all European countries represented in the UEMS PRM Section. Evidence synthesis The systematic literature review is reported together with thirty-three recommendations resulting from the Delphi procedure. Conclusions The role of the PRM physician is to assess the functional status of persons with muscular dystrophy and to plan, monitor and lead PRM program in an interdisciplinary setting within a multiprofessional team.

Over the last few years, the microfluidics phenomenon coupled with the Internet of Things (IoT) using innovative nano-functional materials has been recognized as a sustainable and economical tool for point-of-care testing (POCT) of various pathogens influencing human health. The sensors based on these phenomena aim to be designed for cost-effectiveness, make it handy, environment-friendly, and get an accurate, easy, and rapid response. Considering the burgeoning importance of analytical devices in the healthcare domain, this review paper is based on the gist of sensing aspects of the microfabricated paper-based analytical devices (μPADs). The article discusses the various used design methodologies and fabrication approaches and elucidates the recently reported surface modification strategies, detection mechanisms viz., colorimetric, electrochemical, fluorescence, electrochemiluminescence, etc. In a nutshell, this article summarizes the state-of-the-art research work carried out over the nano functionalized paper-based analytical devices and associated challenges/solutions in the point of care testing domain.

Governance for centralized organizational structures has long roots and well-developed frameworks, including for various specialty areas, such as IT or data governance. However, the introduction of blockchain technology as a supportive tool for implementing decentralized organizations requires a renewed focus for research in the area. The paper utilizes empirical data from blockchain ecosystems in the form of white papers (public communique of intention) to analyze their governance intentions. The empirical findings are based on a review of 241 blockchains and distributed ledger technology white papers, out of which 67 include explicit descriptions of how governance should be organized in the ecosystem. Our empirical research distinguishes between three categories of governance: objectives, mechanisms, and stakeholders. We further identify 28 features for these categories, which are described in an open encoding format. Hence, the paper contributes to the emerging blockchain research field, particularly to the decentralized aspects of blockchain governance research. This research also reveals that blockchain governance does not receive the attention it should as a large majority of ecosystems have not disclosed their governance intentions. The results can be utilized as a framework for future research. The results can also be helpful for industry when designing and developing governance systems.

Tissue paper production frequently combines two main types of raw materials: cellulose fibers from renewable sources and polymer-based additives. The development of premium products with improved properties and functionalities depends on the optimization of both. This work focused on the combination of innovative experimental and computational strategies to optimize furnish. The main goal was to improve the functional properties of the most suitable raw materials for tissue materials and develop new differentiating products with innovative features. The experimental plan included as inputs different fiber mixtures, micro/nano fibrillated cellulose, and biopolymer additives, and enzymatic and mechanical process operations. We present an innovative tissue paper simulator, the SimTissue, that we have developed, to establish the correlations between the tissue paper process inputs and the end-use paper properties. Case studies with industrial interest are presented in which the tissue simulator was used to design tissue paper materials with different fiber mixtures, fiber modification treatments, micro/nano fibrillated cellulose, and biopolymer formulations, and to estimate tissue softness, strength, and absorption properties. The SimTissue was able to predict and optimize a broader range of formulations containing micro/nanocellulose fibers, biopolymer additives, and treated-fiber mixtures, saving laboratory and industrial resources.

This collaborative statement from the Digital Health Committee of the Heart Rhythm Society provides everyday clinical scenarios in which wearables may be utilized by patients for cardiovascular health and arrhythmia management. We describe herein the spectrum of wearables that are commercially available for patients, and their benefits, shortcomings and areas for technological improvement. Although wearables for rhythm diagnosis and management have not been examined in large randomized clinical trials, undoubtedly the usage of wearables has quickly escalated in clinical practice. This document is the first of a planned series in which we will update information on wearables as they are revised and released to consumers.

International audience; Extracellular vesicles (EV) are emergent therapeutic effectors that have reached clinical trial investigation. To translate EV-based therapeutic to clinic, the challenge is to demonstrate quality, safety, and efficacy, as required for any medicinal product. EV research translation into medicinal products is an exciting and challenging perspective. Recent papers, provide important guidance on regulatory aspects of pharmaceutical development, defining EVs for therapeutic applications and critical considerations for the development of potency tests. In addition, the ISEV Task Force on Regulatory Affairs and Clinical Use of EV-based Therapeutics as well as the Exosomes Committee from the ISCT are expected to contribute in an active way to the development of EV-based medicinal products by providing update on the scientific progress in EVs field, information to patients and expert resource network for regulatory bodies. The contribution of our work group "Extracellular Vesicle translatiOn to clinicaL perspectiVEs - EVOLVE France", created in 2020, can be positioned in complement to all these important initiatives. Based on complementary scientific, technical, and medical expertise, we provide EV-specific recommendations for manufacturing, quality control, analytics, non-clinical development, and clinical trials, according to current European legislation. We especially focus on early phase clinical trials concerning immediate needs in the field. The main contents of the investigational medicinal product dossier, marketing authorization applications, and critical guideline information are outlined for the transition from research to clinical development and ultimate market authorization.

Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG Industrial drying lines of resin-impregnated paper are formed by contiguous furnaces where hot air jets impinge on the surface of the moving paper sheet. The number of production parameters that conditions the process is very high, making the final drying prediction, and the optimal adjustment of the production parameters, very complex tasks. A novel numerical tool for the fast prediction of this industrial drying is presented. The model, obtained from local mass and energy equations for the paper sheet, and fed with results from three-dimensional computational fluid dynamic simulations and thermo-gravimetric tests, determines the evolution of the paper weight along the line for any given combination of production parameters: paper velocity, furnaces air temperatures and mass flows, among others. The model is validated in an industrial line with 11 furnaces, 2 impregnation stages, and more than 150 adjustable operational input parameters, leading to relative errors in the predicted paper temperature evolution and final paper weight of less than 7% and 1%, respectively. Likewise, the model coupling with an optimization tool is also presented to show its capabilities on selecting the best production parameters for prescribed conditions, making the model a useful tool in the framework of the increasingly relevant role of mathematical models in industry. Instituto Tecnológico de Matemática Industrial (ITMATI) | Ref. C69-2019 Instituto Tecnológico de Matemática Industrial (ITMATI) | Ref. C80-2020 Instituto Tecnológico de Matemática Industrial (ITMATI) | Ref. C83-2020

INTRODUCTION Amyotrophic lateral sclerosis (ALS) is a progressive motor neuron disease that affects both upper and lower motor neurons and is fatal in its course. This evidence-based position paper represents the official position of the UEMS PRM Section. The aim of the paper is to define the role of the physical and rehabilitation medicine (PRM) physician and PRM professional practice for people with ALS. EVIDENCE ACQUISITION A systematic review of the literature and a consensus procedure by means of a Delphi process have been performed involving the delegates of all European countries represented in the UEMS PRM Section. EVIDENCE SYNTHESIS The systematic literature review is reported together with thirty-two recommendations resulting from the Delphi procedure. CONCLUSIONS The responsibility of the PRM physician is functional assessment of persons with ALS and delivering the optimal and most effective PRM program of care. The rehabilitation program of patients with ALS should be delivered and monitored by the multiprofessional team, with the PRM physician as principal coordinator.

This White Paper has been formally accepted for support by the International Federation for Emergency Medicine (IFEM) and by the World Federation of Intensive and Critical Care (WFICC), put forth by a multi-specialty group of intensivists and emergency medicine providers from low- and low-middle-income countries (LMICs) and high-income countries (HiCs) with the aim of 1) defining the current state of caring for the critically ill in low-resource settings (LRS) within LMICs and 2) highlighting policy options and recommendations for improving the system-level delivery of early critical care services in LRS. LMICs have a high burden of critical illness and worse patient outcomes than HICs, hence, the focus of this White Paper is on the care of critically ill patients in the early stages of presentation in LMIC settings. In such settings, the provision of early critical care is challenged by a fragmented health system, costs, a health care workforce with limited training, and competing healthcare priorities. Early critical care services are defined as the early interventions that support vital organ function during the initial care provided to the critically ill patient—these interventions can be performed at any point of patient contact and can be delivered across diverse settings in the healthcare system and do not necessitate specialty personnel. Currently, a single “best” care delivery model likely does not exist in LMICs given the heterogeneity in local context; therefore, objective comparisons of quality, efficiency, and cost-effectiveness between varying models are difficult to establish. While limited, there is data to suggest that caring for the critically ill may be cost effective in LMICs, contrary to a widely held belief. Drawing from locally available resources and context, strengthening early critical care services in LRS will require a multi-faceted approach, including three core pillars: education, research, and policy. Education initiatives for physicians, nurses, and allied health staff that focus on protocolized emergency response training can bridge the workforce gap in the short-term; however, each country’s current human resources must be evaluated to decide on the duration of training, who should be trained, and using what curriculum. Understanding the burden of critical Illness, best practices for resuscitation, and appropriate quality metrics for different early critical care services implementation models in LMICs are reliant upon strengthening the regional research capacity, therefore, standard documentation systems should be implemented to allow for registry use and quality improvement. Policy efforts at a local, national and international level to strengthen early critical care services should focus on funding the building blocks of early critical care services systems and promoting the right to access early critical care regardless of the patient’s geographic or financial barriers. Additionally, national and local policies describing ethical dilemmas involving the withdrawal of life-sustaining care should be developed with broad stakeholder representation based on local cultural beliefs as well as the optimization of limited resources.

Introduction:The Ministry of Public Health in Lebanon is in the process of converting the surveillance reporting from a cumbersome paper-based system to a web-based electronic platform (DHIS-2) to have real-time information for early detection of alerts and outbreaks and for initiating a prompt response.Objectives:This paper aimed to document the Lebanese experience in implementing DHIS-2 for the disease surveillance system. It also targets to assess the improvement of reporting rates and timeliness of the reported data and to disclose the encountered challenges and opportunities. MethodologyThis is a retrospective description of processes involved in the implementation of the DHIS-2 tool in Lebanon. Initially, it was piloted for the school-based surveillance in 2014; then its use was extended in May 2017 to cover other specific surveillance systems. This included all surveillance programs collecting aggregate data from hospitals, medical centers, dispensaries, or laboratories at the first stage. As part of the national roll-out process, the online application was developed. The customized aggregated-based datasets, organization units, user accounts, specific and generic dashboards were generated. More than 80 training sessions were conducted throughout the country targeting 1290 end-users including health officers at the national and provincial levels, focal persons working in all public and private hospitals, laboratories, and medical centers as well. Completeness and timeliness of reported data were compared before and after the implementation of DHIS-2. Challenges and lessons learned during the roll-out process are listed.ResultsFor laboratory-based surveillance, completeness of reporting increased from 70.8% in May to 89.6% in October. Timeliness has improved from 25% to 74%. For medical centers, an improvement of 8.1% for completeness and 9.4% in timeliness was recorded before and after training sessions. For zero reporting, completeness remains the same (88%) and timeliness has improved from 74% to 87%. The main challenges faced during the implementation of DHIS-2 were mainly infrastructural and system-related in addition to poor internet connectivity and limited workforce and frequent changes to DHIS-2 versions.ConclusionImplementation of DHIS-2 improved timeliness and completeness for aggregated data reporting. Continued on-site support, monitoring, and system enhancement are needed to improve the performance of DHIS-2.

In this study, we describe a monolithic and fully integrated paper-based device for the simultaneous detection of three prognostic biomarkers in saliva. The pattern of the proposed multiplexed device is designed with a central sample deposition zone and three identical arms, each containing a pre-treatment and test zone. Its one-step fabrication is realized by CO2 laser cutting, providing remarkable parallelization and rapidity (ca. 5 s/device). The colorimetric detection is based on the sensitive and selective target-induced reshaping of plasmonic multibranched gold nanoparticles, which exhibit a clear spectral shift (and blue-to-pink color change) in case of non-physiological concentrations of the three salivary biomarkers. A rapid and multiplexed naked-eye or smartphone-based readout of the colorimetric response is achieved within 10 min. A prototype kit for POCT testing is also reported, providing robustness and easy handling of the device.

Purpose The purpose of the study was to appraise the methodological quality of the highest impact blepharoplasty research and to describe prevalent research themes. Methods The 100 most highly cited research papers relevant to blepharoplasty were obtained from Web of Science, with no journal or date limitations applied. Data extraction included the study design, main research topic and specialty, outcome measures, and citation count. Each paper's level of evidence was independently evaluated by 2 authors according to the Oxford Centre for Evidence-Based Medicine system. Results Overall, the 100 most cited blepharoplasty research papers were cited by 4,194 papers. The mean number of citations for each paper was 73 (range: 42-239). Most of the papers presented level 4 (n = 51) or level 5 (n = 35) evidence, which is consistent with the predominance of case series (n = 47) and expert opinions (n = 18) amongst study designs. No papers achieved level 1 (highest) evidence. Six papers presented level 2 evidence and 8 papers presented level 3. Significant research foci included innovative surgical techniques (n = 65) and anatomical considerations (n = 10), with reconstructive and cosmetic implications. Senior authors were mainly affiliated with centers of plastic (n = 53) or ophthalmic/oculoplastic (n = 34) surgery. Only 3 papers used validated subjective or objective cosmetic outcome measures. Conclusions Despite a significant impact on current practice, the level of evidence of the highly cited blepharoplasty research was predominantly low. Robust research methodology, through well-designed studies and standardized outcome measures, is necessary to facilitate evidence synthesis and guide clinical practice.

Cellulose paper derived from plants is used for daily writing and recording, and has historically played an important role in promoting cultural dissemination and inheritance. However, it attracted more and more attentions in recent years serving as a flexible platform or substrate for application in environment and energy, attributing from its many inherent advantages such as biocompatibility, biodegradability, sustainability, low cost, and great capability to be modified. With the development of various industries, especially the flexible electronics industry, the demand for two-dimensional (2D) paper-like materials has increased. Several kinds of inorganic paper are manufactured and have been widely used in many fields. Among them, there are hydroxyapatite (HAP)-based and carbon-based inorganic paper that give play to their own advantages and have been well applied in some fields. In addition, there are many composite papers, which are assembled from several raw materials (cellulose fibers, HAP, carbon), exhibiting excellent characteristics. Cellulose paper is no longer limited to traditional writing applications, but has great potential to be used in many aspects, achieving a gorgeous change in its role. The emergence of inorganic paper and hybrid paper has further demonstrated the application prospects of paper-like two-dimensional materials. This paper will start from the characteristics of the three types of paper and composite paper, and summarize their typical applications in the environment and energy fields.