Search

Considering the high demand for innovative solutions in medicine, a major increase in interest in biomaterials research has been noticed, with the most significant advancements in metals and their alloys. Titanium-based alloys are one of the most recognised in the scientific community but do not represent the only way to achieve optimal results. Zirconium alloys for medical applications are a novelty with significant research potential based on their outstanding properties, which may be of value for medicine. The aim of the present study was to obtain new biomedical Zr-Nb-Mo alloys with varying ratios of their respective elements—Zr and Mo—using combined powder metallurgy (PM) and arc melting (VAM) methods. The obtained samples underwent microstructure analysis using an optical microscope (OM) and a scanning electron microscope (SEM). The study of element distribution was conducted with energy dispersive spectroscopy (EDS), whereas the phase composition was determined using X-ray diffraction (XRD). Mechanical properties were examined with a Micro Combi Tester MCT3, whereas tribological properties were assessed with a TRN Tribometer, and Ringer's solution was used as a lubricant. Additionally, the wear tracks of the studied samples were observed using the SEM. The research results indicated that increased Mo content conduced to microstructure refinement and homogeneity. Furthermore, the higher content of this element contributed to the growth of the HVIT, HIT, and EIT parameters, together with the improvement in the tribological performance of the alloys. XRD analysis revealed that the obtained samples were multiphase, and raising the Mo addition promoted the formation of new phases, including a ternary phase—Zr0.9Nb0.66Mo1.44 (Fd 3 ¯ m). The chemical composition study showed uneven distribution of niobium and areas of uneven mutual distribution of zirconium and molybdenum. [ABSTRACT FROM AUTHOR]

To perform quality assessments of both metal alloys and many other engineering materials, measurements of the volume fractions of phases or microstructure components are utilized. For this purpose, quantitative analysis of the evaluated components' distribution on metallographic specimens is often employed. Phases or components of the microstructure are identified based on the variation in signal received in the band of light seen. Problems with the correct identification of measurement results in this spectral band can be caused by the inhomogeneity of the etching when the alloy components are segregated. Additional uncertainty arises when the analyzed image pixel contains a boundary between grains of different phases. This article attempts to use the results of local chemical composition measurements as a source signal for quantitative evaluation of phase composition. For this purpose, quantitative maps of elemental concentration distributions, obtained with a Tescan Mira GMU high-resolution scanning electron microscope in QuantMap mode, were used as input data for the phase composition evaluation of an EN AC 46000 alloy sample. The X-ray microanalysis signal generation area may contain grains of more than one phase. Therefore, evaluation of the phase fractions in areas of individual measurements were calculated by looking for the minimum of the objective function, calculated as the sum of the squares of the deviations of the results of measurements of the concentration of individual elements from the weighted average values of solubilities of these elements in the phases. [ABSTRACT FROM AUTHOR]

The FurnaSEM microfurnace was installed in the chamber of a scanning electron microscope to carry out in situ experiments at high temperatures and test its limits. The microfurnace was used in combination with different types of detectors (Everhart–Thornley for the collection of secondary electrons in a high vacuum, gas secondary electron detector for the specific collection of secondary electrons in the presence of gas, and Karmen© detector for the collection of backscattered electrons at high temperature). Experiments carried out on various samples (metal alloys and ceramics) show that the microfurnace operates in both high-vacuum and low-vacuum modes. Temperature ramp rates during temperature cycles applied to the sample range from 1 to 120 °C/min (temperature rise) and 1 to 480 °C/min (controlled and natural cooling). The maximum temperature at which images were recorded up to 25 k × magnification was 1340 °C, with a residual air atmosphere of 120 Pa. The choice of a flat furnace with the sample placed directly above it has enabled innovative experiments to be carried out, such as low-voltage imaging (using a shorter working distance—up to 10 mm—than is possible with conventional furnaces), 3D imaging (by tilting the stage by up to 10°), and high-temperature backscattered electron imaging (using a dedicated detector). [ABSTRACT FROM AUTHOR]

The microstructure and properties of an AlSi10Mg alloy produced by selective laser melting were examined using optical microscopes, scanning electron microscopes, electron backscattered diffraction, and x‐ray diffraction. The results show that the mechanical characteristics of selective laser melting formed AlSi10Mg alloy is superior to those of traditional sand cast AlSi10Mg alloy due to fine grain strengthening and solid solution strengthening. AlSi10Mg alloy formed by selective laser melting is mainly composed of α‐aluminum solid solution, eutectic silicon with network structure and a small amount of Magnesium silicon precipitated phase, and different cross‐sections have unique microstructures and properties. The XOY plane is composed primarily of equiaxed grains with an average grain size of 7.34 μm and a {001} <100> cubic texture, and it has a hardness value of 130.7 HV 0.2. The majority of the YOZ plane, which has a {111}<110> brass R texture and a hardness value of 108.9 HV 0.2, comprises columnar crystals with an average grain size of 8.42 μm. [ABSTRACT FROM AUTHOR]

The effect of Ru addition on the martensitic transformation and mechanical properties of Zr50Pd50−xRux SMAs shape memory alloys has been studied. Strain–temperature experiments, differential scanning calorimeter, and scanning electron microscope analyses were performed to validate the theoretical predictions by DFT calculation regarding the influence of the C′ parameter on martensitic stability. Despite the absence of an observed shape memory effect under the tested conditions, the findings suggest that ZrPdRu alloys hold promise for high-temperature applications. [ABSTRACT FROM AUTHOR]

Using the tin alloy module in the material phase diagram and thermodynamic simulation software JMatPro, the phase compositions of different components of Sn-Bi-Pb low melting point alloys with the same Sn content were simulated based on the phase diagrams of Sn-Bi, Sn-Pb, and Pb-Bi binary alloys, and the influence of alloying element content on the melting characteristics of the alloys was investigated, which was used for the optimization of the components and the obtaining of low melting point alloys with excellent melting characteristics. The microstructure and melting characteristics of the optimized alloys were characterized by Scanning electron microscope (SEM), Thermogravimetry Analysis-Differential Scanning Calorimetry (TG-DSC), X-ray diffractometer (XRD), etc., and the influence of phase content on the mechanical properties was investigated. The results show that the Sn-Bi-Pb alloy possesses Sn-(Bi, Pb) phase, Bi-(Pb) phase and Pb7Bi3 intermetallic compound phase, and the simultaneous increase of the Bi element and decrease of the Pb element content to the Sn-Bi-Pb alloy obviously improves its tensile strength, but the elongation rate shows a decreasing trend, among which Sn50Bi30Pb has the optimal comprehensive performance, with a tensile strength of 38.60 MPa, an elongation of 61.13%, and a melting range of 94.0℃~100.6℃. [ABSTRACT FROM AUTHOR]

Cu additions notably strengthen Al-Mg-Si and Al-Si-Mg alloys due to the dense precipitation of quaternary nano precipitates during ageing. However, the chemical evolution and mechanical behaviors of the quaternary micro-scale Q constituent phase occurring in cast and homogenized states have rarely been studied. Meanwhile, there exists a type of AlCuMgSi cluster in the cast state, which has been regarded as Q particles. The accurate identification of phase constituents is the basis for the future design of alloys with better performance. In our work, this type of cluster was revealed to consist of α-Al, θ-Al2Cu, Q, and Si phases through micro-to-atomic scale studies using scanning and transmission electron microscopes. The skeleton of the dendrite was θ phase. The second phases in the dendritic eutectic cluster dissolved quickly during a 4 h homogenization at 550 °C. The Q phase was found to effectively absorb the Fe impurities during casting and homogenization. As a result, the formation of other harmful Fe-rich intermetallics was suppressed. These Q constituent particles were observed to break into separate pieces in an intermediately brittle manner when compressed in situ in a scanning electron microscope. These findings provide insights into the thermodynamic modeling of the Al-Mg-Si-Cu system and alloy design. [ABSTRACT FROM AUTHOR]

Titanium alloys have broad application prospects in the field of marine engineering due to their excellent corrosion resistance and comprehensive mechanical properties. Titanium alloys, when connected with other metals, such as copper-nickel alloys, could produce two distinct effects. On the one hand, the passive film gives titanium alloys positive potential, which could accelerate galvanic corrosion of negative-potential metals. On the other hand, the passive film could obstruct current flow and prevent further development of galvanic corrosion. In this paper, Potentiodynamic Polarization, Electrochemical Impedance Spectroscopy, and Electrochemical Noise techniques were utilized to investigate the galvanic corrosion behavior of B10/Ti80 under simulated seawater environment. The corrosion morphology and product composition were studied using Scanning Electron Microscope and X-ray Photoelectron Spectroscopy. The above experimental results showed that Ti80 and B10 served as the anode and cathode respectively in the early stages of corrosion (within 2.5 h of immersion), due to the incomplete formation of the passivation film on Ti80. While in the latter stages of corrosion, due to the positive shift of Ti80's potential by passivation, there was a noticeable accelerated corrosion effect on B10, which was proportional to the area ratio of Ti80/B10 and showed a gradually stable trend after 28 days of immersion in the seawater. [ABSTRACT FROM AUTHOR]

Objectives: This study aims to investigate the effect of coating time on the formation of hydroxyapatite (HA) coating layer on ZK60 substrate and understand the biodegradation behavior of the coated alloy for biodegradable implant applications. Methods: Biodegradable ZK60 alloy was coated by HA layer for different times of 0.5, 1, 2, and 4 h by chemical conversion method. After coating, all the coated specimens were used for immersion test in Hanks' solution to understand the effect of coating time on the degradation behavior of the alloy. The degradation rate of the coated alloy was evaluated by Mg2+ ion quantification and pH change during immersion test. The microstructure of the coating layer was examined by scanning electron microscope (SEM) equipped with an energy-dispersive X-ray spectroscopy (EDS) before and after immersion to understand the degradation behavior of the coated alloy. Results: HA coating layers were formed successfully on surface of ZK60 specimens after 0.5, 1, 2, and 4 h with different microstructure. Optimal coating quality was observed at 1 or 2 h, characterized by well-formed and uniform HA layers. However, extending the coating duration to 4 h led to the formation of cracks within the HA layer, accompanied by Mg(OH)2. Specimens coated for 1 and 2 h exhibited the lowest degradation rates, while specimens coated for 0.5 and 4 h showed the highest degradation rates. Furthermore, analysis of degradation products revealed the predominance of calcium phosphates formed on the surface of specimens coated for 1 and 2 h. Conversely, specimens coated for 0.5 and 4 h exhibited Mg(OH)2 as the primary degradation product, suggesting a less effective corrosion barrier under these conditions. Conclusion: The HA layer formed after 2 h demonstrated as the most effective coating layer for enhancing the corrosion resistance of the ZK60 alloy for biomedical applications. [ABSTRACT FROM AUTHOR]

This paper reports the results of our study on electrochemical polishing of titanium and a Ti-based alloy using non-aqueous electrolyte. It was shown that electropolishing ensured the removal of surface defects, thereby providing surface smoothing and decreasing surface roughness. The research was conducted using samples made of titanium and Ti6Al4V alloy, as well as implant system elements: implant analog, multiunit, and healing screw. Electropolishing was carried out under a constant voltage (10–15 V) with a specified current density. The electrolyte used contained methanol and sulfuric acid. The modified surface was subjected to a thorough analysis regarding its surface morphology, chemical composition, and physicochemical properties. Scanning electron microscope images and profilometer tests of roughness confirmed significantly smoother surfaces after electropolishing. The surface profile analysis of processed samples also yielded satisfactory results, showing less imperfections than before modification. The EDX spectra showed that electropolishing does not have significant influence on the chemical composition of the samples. [ABSTRACT FROM AUTHOR]

In this paper, the microstructure and mechanical properties of Al-6.5Si-5.5Cu-0.2Zr-0.01Sr-0.06Ti-0.2Ce cast aluminum alloys were investigated in multistage solid solution systems. The microstructure of the alloy was characterized using an optical microscope (OM), scanning electron microscope (SEM), energy-dispersive spectrometer (EDS), x-ray diffraction (XRD) and transmission electron microscope (TEM), respectively. The hardness and conductivity of the alloy were measured using a Vickers hardness and eddy current conductivity testers, respectively, and the tensile properties were described by a drawing machine. The results showed that the mechanical properties of the alloy are the worst under the four-stage solid solution system (G1). With the increase in multistage solution temperature and holding time, θ phase (Al2Cu) was gradually dissolved into α-Al matrix to enhance the effect of dislocation strengthening. When the solution temperature reached 510 °C, the mechanical properties of the alloy were the best, and the tensile strength and elongation were increased to 354.90 MPa and 9.02%, respectively. With the increase in temperature, eutectic Si agglomeration and large area of insoluble phase between metals were found, resulting in the decrease in mechanical properties. [ABSTRACT FROM AUTHOR]

Magnesium and its alloys are advantageous in clinical applications due to their excellent mechanical properties and suitable biological properties. However, due to their high corrosion rate in physiological environments, these alloys' application was limited. Polypyrrole (PPy) coatings were potentiostatically deposited on AZ31 alloy to reduce its corrosion rate in this study. The effect of applied potential and monomer concentration on the coatings' characteristics and properties such as wettability, corrosion resistance, and adhesion strength was studied. The coatings had cauliflower and porous micro-granular morphologies, according to scanning electron microscope images. The thickness and average roughness of the coatings increased from 0.3 to 3.8 µm and 18.3 to 43.7 nm, respectively, as the monomer concentration in the deposition bath was increased from 0.1 to 0.2 M. Increasing the applied potential had the same effect on thickness and roughness. According to the water contact angle (WCA) results, the alloy and all of the PPy coatings were hydrophilic. However, increasing the monomer concentration of the bath and the applied potential increased the WCA of the coatings. The electrochemical behavior of the samples in Ringer's solution was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. All of the coatings outperformed the bare substrate in terms of corrosion resistance. The corrosion current density of the optimum PPy coating obtained from a bath with 0.2 M pyrrole monomer at 3 V was approximately seven times lower than that of the AZ31 alloy. In the cross-cut adhesion test, this coating also demonstrated the best adhesion to the substrate. [ABSTRACT FROM AUTHOR]

Because of their high mixing entropies, multi-component alloys can exhibit enhanced catalytic activity compared to traditional catalysts in various chemical reactions, including hydrogenation, oxidation, and reduction processes. In this work, new AgCoCuFeNi high entropy alloy nanoparticles were synthesized by the hydrogen reduction-assisted ultrasonic spray pyrolysis method. The aim was to investigate the effects of processing parameters (reaction temperature, precursor solution concentration, and residence time) on the microstructure, composition, and crystallinity of the high entropy alloy nanoparticles. The characterization was performed with scanning electron microscope, energy-dispersive X-ray spectroscopy, and X-ray diffraction. The syntheses performed at 600, 700, 800, and 900 °C, resulted in smaller and smoother spherical particles with a near-equiatomic elemental composition as the temperature increased to 900 °C. With 0.25, 0.1, and 0.05 M precursor solutions, narrower size distribution and uniform AgCoCuFeNi nanoparticles were produced by reducing the solution concentration to 0.05 M. A near-equiatomic elemental composition was only obtained at 0.25 and 0.05 M. Increasing the residence time from 5.3 to 23.8 s resulted in an unclear particle microstructure. None of the five metal elements were formed in the large tubular reactor. X-ray diffraction revealed that various crystal phase structures were obtained in the synthesized AgCoCuFeNi particles. [ABSTRACT FROM AUTHOR]

The article presents a precise method for the orientation process of NiMnGa-based single crystals. For this method, a scanning electron microscope equipped with an EBSD camera and a heating stage allowing temperatures exceeding 873 K was used. The orientation process was carried out in both the high-temperature austenite phase and in the room-temperature martensite phase. The facilities allowed for determining the orientation of a single grain of austenite at elevated temperatures as well as the orientation of particular martensitic variants at room temperature. A practically perfect cubic orientation was obtained in the austenitic case with a deviation of about 1° while the samples oriented in the martensitic phase deviated from the desired orientation by 4.5-5.2°. Additionally, the training process of single crystals was carried out in order to show the influence of the orientation process on twinning stress. [ABSTRACT FROM AUTHOR]

The as-received AZ91D Mg alloy was coated with ZrO2 and ZrN ceramics using the Physical Vapour Deposition (PVD) process. Dry sliding wear investigations were performed in a pin-on-disc wear tester at a sliding velocity of 2-8 m/s and a normal load of 2-10 N. The wear mechanisms such as abrasion, delamination, thermal softening, and oxidation were observed. The results showed that PVD coating increased the wear resistance of AZ91D Mg alloy. The worn surface was examined with Scanning Electron Microscope (SEM). [ABSTRACT FROM AUTHOR]

This study investigated the microstructure, hardness, tensile and tribological behaviour of a cooling slope Al--Si--Mg alloy following ECAP and T6 heat treatment. The optical and scanning electron microscopes were applied to investigate the microstructure of the as-cast material and heattreated ECAPed Al--Si--Mg alloy. The dry sliding wear test was tested with three different loads of 10 N, 50 N, and 100 N with constant sliding speed and sliding distance at 1.0 m/s and 9000 m, respectively, using the pin-on-disc tribometer. The hardness and tensile properties were evaluated through microhardness, UTS, and YS measurement for the as-cast Al--Si--Mg alloy, both heat-treated with and without ECAPed alloys. Moreover, wear rate and COF in the Al--Si--Mg alloy with different loads were analysed and linked with microstructural and strength behaviour after the ECAP process. Meanwhile, these analyses of results were correlated with the behaviour of the as-cast Al--Si--Mg aluminium alloy and heat-treated non-ECAPed alloy. Results demonstrated that a combination of ECAP processing and T6 heat treatment improves the mechanical behaviour, while the COF and wear rate are improved at a load of 100 N. [ABSTRACT FROM AUTHOR]

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire-drawing machines, very fine wire-drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500 °C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931 × 10−8 Ω·m to 1.723 × 10−8 Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635 × 10−8 Ω·m. [ABSTRACT FROM AUTHOR]

This work investigates the microstructure characterization and mechanical properties of Al alloy fabricated by additive friction stir deposition (AFSD). Microstructure characterizations of the Al alloy 5B70 base material (BM) and build were compared using optical microscope (OM) and electron back scattered diffraction (EBSD). The hardness distribution in the direction perpendicular to the cross-section of the deposited area was systematically evaluated. Tensile tests were performed on the BM and the build using digital image correlation (DIC), and the real-time stress distribution states of the specimens were analyzed. After the tensile tests, the fracture micromorphology was characterized using scanning electron microscope (SEM). The results indicated that a high degree of recrystallization occurred in the deposition zone, where fine, equiaxed, and differently oriented grains are formed. It was found that the strength of the deposition layer was lower compared to that of the BM, but its toughness was significantly improved. Also, obvious anisotropy of mechanical properties was identified in the deposition layer. [ABSTRACT FROM AUTHOR]

The paper aims to investigate the influence of silver addition on the microstructure of CuNi2Si1 alloys. The investigated copper alloy was cast and then supersaturated, plastically deformed on the Gleeble 3800 simulator and finally aged. Structural changes were examined using optical microscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Orientation mapping was completed with FEI Quanta 3D field emission gun scanning electron microscope (SEM) equipped with TSL electron backscattered diffraction (EBSD) system. The effect of structural and microstructural changes on hardness and conductivity was also investigated. Based on the mechanical tests it was found that the mechanical properties and conductivity are improved due to heat and plastic treatment. It was also found that the precipitation hardening raises the hardness to the level of 40% whilst an increase in conductivity by 20% is observed. [ABSTRACT FROM AUTHOR]

The purpose of this work is to study the influence of thermal effect on the surface morphology of the Fe–Cr–Al (Kh15Yu5) alloy foil and the elemental composition of the surface layers. Also, studies have been carried out on the physicochemical characteristics of the primary support with the deposited secondary support in the initial state and within the temperature range from 25 to 900 °C. The research was carried out on a JSM 6610 LV, JEOL scanning electron microscope with an installed INCA Energy 450 energy-dispersive microanalysis system. Before depositing secondary support (aluminum oxide), for a stronger adhesion to the foil metal, the foil surface was pretreated with a phosphating solution. It was found that during heating up the elemental composition of the surface layer of the Kh15Yu5-alloy foil does not remain constant and depends on the mode of thermal effect. This implies the possibility of changing the adhesion and adsorption properties of the foil surface, as well as the need to take this into account when depositing secondary support and an active phase to the foil. Studies have shown that the applied methods for phosphatizing and depositing secondary support to the foil surface make it possible to obtain a quite resistant coating. No peeling of the secondary support from the foil surface is observed during high-temperature treatment in the air. [ABSTRACT FROM AUTHOR]

This project studies the influence of different grain sizes of Ni-based Fe-33Ni-19Cr alloy obtained from heat treatment procedure on high temperature isothermal oxidation. Heat treatment procedure was carried out at two different temperatures, namely 1000°C and 1200°C for 3 hours of soaking time, followed by quenching in the water. These samples are denoted as T1000 and T1200. The heat-treated Ni-based Fe-33Ni-19Cr alloy was subjected to an isothermal oxidation test at 950°C for 150 hours exposure. Oxidized heat-treated alloys were tested in terms of oxidation kinetics, phase analysis and surface morphology of oxidized samples. Oxidation kinetics were determine based on weight change per surface area as a function of exposure time. Phase analysis was determined using the x-ray diffraction (XRD) technique and surface morphology of oxidized samples was characterized using a scanning electron microscope (SEM). As a result, the heat treatment procedure shows varying grain sizes. The higher the heat treatment temperature, shows an increase in grain size with a decrease in hardness value. The oxidation kinetics for both heat-treated samples showed an increment pattern of weight change and followed a parabolic rate law. The oxidized T1000 sample recorded the lowest parabolic rate constant of 3.12×10-8 mg2cm-4s-1, indicating a low oxidation rate, thus having good oxidation resistance. Phase analysis from the XRD technique recorded several oxide phases consisting of Cr2O3, MnCr2O4, and (Ti0.97Cr0.03)O2 oxide phases. In addition, a uniform oxide layer is formed on the oxidized T1000 sample, indicating good oxide scale adhesion, thereby improving the protective oxide behavior. [ABSTRACT FROM AUTHOR]

Thin-walled Al-Mg-Si alloy profiles with different compositions and aging states were prepared using the heating and extrusion process. The properties and structure of the profiles were then investigated using a metallographic microscope, scanning electron microscope, projection electron microscope, and universal testing machine. The results show that the yield strength and tensile strength of the profile increases with the increase in total Mg + Si content, and ductility is reduced. If the total Mg + Si content is too high or too low, the crush performance of the material would decrease. Compared with the under-aged and near-peak-aged states, the three types of AI-Mg-Si alloy thin-walled profiles at the over-aged state have better effective energy absorption during crushing and higher bending angle; however, the tensile strength of the profile is optimal at the near-peak-aged state. The effects of alloy composition and aging process on material strength and crushing energy absorption are mainly attributed to the grain structure and differences in precipitation. For coarse grain structures, the grain boundary precipitate free zones are wider, which decreases the profile ductility. Simultaneously, an increase in primary strengthening phases in the grains would increase the profile strength. [ABSTRACT FROM AUTHOR]

Micron‐sized graphite particles additions to Al2011 alloy were investigated to know their impact on mechanical properties. The stir cast method was used to manufacture the Al2011 alloy with 2 and 4 wt% of graphite particles reinforced composites. The microstructural analysis and mechanical properties of the synthesized composites were tested. Scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) spectrums were used to characterize the microstructure of the samples that were obtained from the casting. SEM micrographs indicated the homogeneous distribution of particles and the EDS patterns confirmed the presence of graphite particles. Al2011 alloy hardness was decreased with the addition of graphite particles. Further, with the addition of 2 and 4 wt% of graphite particles in the Al2011 alloy, the ultimate tensile and yield strengths of composites were increased with increase in elongation. SEM micrographs of tensile fractured surfaces were used to study the various fractured behaviors in the Al2011 alloy‐graphite composites. [ABSTRACT FROM AUTHOR]

This study investigates the new surface development on AA6061 and AA5086 alloys considering the wire-arc additive manufacturing technique as a direct energy deposition (DED) process of wire. Two different quantities of MWCNTs, i.e., 0.01 (low) and 0.02 (high) g, with a constant nickel (Ni) weight (0.2 g) were pre-placed in the created square patterns. ER4043 filler was used as a wire for additive deposition, and an arc was generated through a tungsten inert gas (TIG) welding source. Furthermore, hardness and pin-on-disk wear-testing methods were employed to measure the changes at the surfaces with the abovementioned inducements. This work was designed to illustrate the hardness and the offered wear resistance in terms of mass loss of the AA6061 and AA5086 aluminum alloys with the function of nano-inducements. Two sliding distance values of 500 m and 600 m were selected for the wear analysis of mass loss from tracks. A maximum increase in hardness for AA6061 and AA5086 alloys was observed in the experiments, with average values of 70.76 HRB and 74.86 HRB, respectively, at a high mass content of MWCNTs. Moreover, the tribological performance of the modified surfaces improved with the addition of MWCNTs with Ni particles in a broader sense; the modified surfaces performed exceptionally well for AA5086 compared to AA6061 with 0.02 and 0.01 g additions, respectively. The system reported a maximum of 38.46% improvement in mass loss for the AA5086 alloy with 0.02 g of MWCNTs. Moreover, the morphological analysis of the developed wear tracks and the mechanism involved was carried out using scanning electron microscope (SEM) images. [ABSTRACT FROM AUTHOR]

Due to the poor activation performance and kinetics of Ti50V25Cr25 alloys, the element Zr was added to improve the phase structure of the alloy and achieve a high-performance hydrogen storage alloy. The Ti50−xV25Cr25Zrx (x = 0, 5, 7, and 9) system alloys were prepared by arc melting. The alloys were analyzed using an X-ray diffractometer (XRD), scanning electron microscope (SEM), and differential scanning calorimeter (DSC). The hydrogen storage capabilities of the alloys were also obtained by the Sievert volumetric method. The results indicated that the alloy with Zr added had a combination of the C15 Laves phase and the BCC phase, whereas the Zr-free alloy had a BCC single phase. The partial replacement of Zr with Ti resulted in an increase in the lattice parameters of the main phase. The hydrogen storage kinetic performance and activation of the alloys both significantly improved with an increasing Zr concentration. The time to reach 90% of the maximum hydrogen storage capacity decreased to 2946 s, 230 s, and 120 s, respectively, with the increases in Zr concentration. The initial hydrogen absorption content of the alloys increased and then decreased after the addition of the element Zr. The second phase expanded with an increasing Zr concentration, which in turn decreased the abundance of the BCC main phase. The Ti43V25Cr25Zr7 alloy showed good cycle stability and hydrogen-desorption performance, and it could absorb 90% of the maximum hydrogen storage capacity in around 230 s. The maximum hydrogen-absorption capacity of the alloy was 2.7 wt%. The diffusion activation energy of hydrogen desorption dropped from 102.67 kJ/mol to 92.62 kJ/mol. [ABSTRACT FROM AUTHOR]

To improve the corrosion behavior and discharge performance of Mg–1Sn‐based Mg–air battery anodes, Zn/Ca alloying elements are added in the alloys to modify the type and morphology of the formed second phases. Scanning electron microscope is used to observe the microstructure, and X‐ray diffraction is used to identify the phases formed. Immersion, electrochemistry techniques, and Mg–air battery tests are used to characterize the corrosion and discharge performance of the alloys. The results indicate that the addition of Ca rather than Zn has better effects in improving the corrosion resistance and discharge performance of Mg–1Sn‐based alloys. The second‐phase combination improves the corrosion resistance and electrochemical activity of Mg–1Sn‐based alloys in the following order: Mg2Ca and CaMgSn phases (Mg–1Sn–1Ca alloy) > Ca2Mg6Zn3 and CaMgSn phases (Mg–1Sn–1Zn–1Ca alloy) > the net‐shape Mg4Zn7 + Mg2Sn phases (Mg–1Sn–1Zn alloy) > Mg2Sn phase (Mg–1Sn alloy). In addition, Mg–1Sn–1Zn–1Ca alloy exhibits the highest anodic efficiency, specific capacity, and specific energy among four alloys, i.e., 54.3 , 1197.6 mA h g−1, and 1366.1 mW h g−1, respectively, at a current density of 20 mA cm−2. [ABSTRACT FROM AUTHOR]

In the present paper, microstructural changes in two alloys, IN617 and DMV617 mod, after 5 h and 1000 h of aging at 700 °C were investigated using scanning transmission electron microscopy. The mechanical properties of the samples were evaluated using hardness tests. Precipitates were identified using energy-dispersive X-ray spectroscopy analysis. After long-term aging, intensive precipitation of the M23C6 carbides and γ′ intermetallic phase in the microstructure of alloys was observed. In the IN617 alloy, continuous layers of M23C6 carbides along the grain boundaries after long-term aging were observed. The minor addition of boron to the DMV617 mod alloy is advantageous in microstructure formation during long-term aging because it decreases the agglomeration of M23C6 at the grain boundaries. [ABSTRACT FROM AUTHOR]

This paper investigates the effect of the element La on plasma nitriding of the CoCrCuFeNi high-entropy alloy (HEA) at 440 °C for 8, 16, and 24 h. The phase composition, morphology, and hardness distribution of the nitrided layer are characterized using XRD, optical microscopy, and a microhardness tester. Furthermore, the corrosion resistance is tested using an electrochemical workstation. The study evaluated the friction and wear performance using a testing machine and scanning electron microscope. The thickness of the effective hardening layer after 16 h of treatment with La was similar to that after 24 h of treatment without La. The addition of La significantly increased the growth rate constant of the effective hardening layer from 0.53 × 10−14 m2/s to 0.72 × 10−14 m2/s. In addition, an expanded FCC phase with greater interplanar spacing can be formed on the surface of the sample by introducing La into the plasma nitriding process. This indicates that the expanded FCC phase, with a higher concentration of interstitial nitrogen atoms, can effectively improve the corrosion resistance of the specimen surface. The corrosion rate of the specimen surface was reduced by 27.5% and the wear rate was reduced by 41.7% after 16 h of treatment with the addition of La compared to 24 h of nitriding without the addition of La. It has been shown that the addition of La to the plasma nitriding process results in a higher quality nitrided layer in a shorter time and also demonstrates that La has the potential to optimize the surface properties of plasma nitrided HEAs. [ABSTRACT FROM AUTHOR]

The anisotropic damage behavior has a great influence on the formability of rolling sheets. This work aimed to investigate the anisotropic damage mechanism of the LA103Z Mg‐Li alloy rolling sheet by combining mesoscale detection and modeling. The X‐ray computed tomography (XCT) and scanning electron microscope (SEM) were applied to characterize the evolution of damage morphology and volume fraction in RD, DD, and TD directions of the rolling sheet. The GTN damage model was calibrated by the experimental results with the representative volume element (RVE) method. The anisotropic damage mechanism was revealed via experimental and modeling results. The micro void nucleation strain εN was critical to determine the initiation moment of the anisotropic damage. The continuous nucleation in RD direction, the severe growth in DD direction, and the massive coalescence in TD direction were the micro void evolution competition results that caused the anisotropy for damage mechanism and fracture strain. Highlights: The micro void evolution was quantitatively characterized by XCT and SEM methods.The GTN damage model calibrated by the RVE method exhibited accurate prediction.εN was the critical strain for determining the initiation of anisotropic damage.Anisotropic damage was caused by different responses of micro void evolution. [ABSTRACT FROM AUTHOR]

The paper reports on the atomic investigation about β phase in Mg 96 Gd 2 Y 1 Ni 1 alloy by using the first-principles study and the high-angle annular dark-field scanning transmission electron microscope (HAADF-STEM) corrected by atomic Cs. By using HAADF-STEM, the rectangular β phases were observed in the underage and peak aging stages in Mg 96 Gd 2 Y 1 Ni 1 alloy. The β phase could be precipitated from the previously precipitated β phase, and the β phase grew in steps when it was precipitated. A special transition structure of three atomic layer thicknesses was first observed at the edge of the β phase and the structure of this interface is probably as the β/Mg 1 interface for the analysis of thermodynamic characterization and electronic characterization. The β' phase and the β H structure were precipitated only at the edge of the length directions of the β phase. The β' phase continues to grow into a β phase directly without the formation of β 1 phase, resulting in an increase in the length of the β phase, which is discovered for the first time. [ABSTRACT FROM AUTHOR]

In order to improve the corrosion resistance of Mg-3Gd-1Zn-0.4Zr (GZ31K) alloys for biomedical application, the alloy was micro-arc oxidation (MAO)-treated using silicate electrolyte system under various voltages (400 V, 425 V, 450 V, 475 V). The effects of voltage on the microstructure and corrosion properties of MAO coating were investigated via X-ray diffraction (XRD) and a scanning electron microscope (SEM) combined with an energy-dispersive spectrometer (EDS), X-ray photoelectron spectroscope (XPS), and electrochemical experiments. The results showed that, with the increase in voltage, the MAO coatings became thicker and the micropores on the MAO coating increased in diameter. The main phase compositions of the MAO coatings were MgO and Mg2SiO4. Potentiodynamic polarization curve results showed that MAO coatings could enhance corrosion resistances, where the corrosion current density decreased by six orders of magnitude and the corrosion potential of the specimens increased by 300 mV for the voltage of 450 V in the MAO treatment; nevertheless, the corrosion resistance rapidly deteriorated due to the creation of large micropores in the MAO coating, which provide a pathway for corrosive media when the voltage is 475 V. The electrochemical impedance spectroscopy results showed that MAO treatments could increase low-frequency modulus resistance and increase the corrosion resistance of Mg alloys. In addition, MAO-treated GZ31K alloys still exhibited uniform corrosion, which is desirable for biomedical applications. [ABSTRACT FROM AUTHOR]

Aluminum alloys are extensively used to manufacture mechanical components. However, when exposed to alkaline environments, like lubricants, refrigerants, or detergents, they can be corroded, reducing their durability. For this reason, the aim of this study is to investigate the influence of aggressive alkaline solutions (i.e., pH and presence of chlorides) on the corrosion resistance of three aluminum alloys (AA 5083-H111, AA 6082-T6, and AA 7075-T6) with and without anodizing treatments. Open circuit potential (EOCP) and anodic polarization measurements were carried out and typical corrosion parameters such as corrosion current density (icor) and corrosion rate (CR) were determined. Morphology of the corrosion attack and samples microstructure were investigated by scanning electron microscope. Results show that corrosion behavior of the three investigated alloys is influenced by (i) the aggressiveness of the testing environments; (ii) the thickness of the anodizing treatment; (iii) the alloy chemical composition; (iv) the distribution of intermetallic phases in the aluminum matrix. Moreover, three galvanic series have been built also testing other metallic alloys commonly used in mechanical applications, i.e., carbon steel (C40), stainless-steel (AISI 304), and Cu-based alloys (Cu-Ni alloy and CW 617 N, respectively). Results clearly indicate that galvanic series play a fundamental role when it is necessary to select an alloy for a specific environment, highlighting the thermodynamic conditions for corrosion occurrence. On the other hand, kinetic measurements and microstructural studies carried out on the three aluminum alloys stress the importance of the surface treatments and relevant thickness as well as the effect of metal exposure. Future work will involve the study of other surface treatments on aluminum alloys and the evaluation of their corrosion behavior in acidic environments. [ABSTRACT FROM AUTHOR]

In this study, the effect of aging at different temperatures and times on the properties of AA7075-T6 alloy was investigated. The samples prepared for the experimental studies were subjected to the solution, quenching, and then aging heat treatment at 100 °C and 200 °C for different periods (42-66-90 hours). The properties of the experimental samples were investigated by hardness, compression test, and scanning electron microscope (SEM). As a result of the studies, it was determined that the aging heat treatment had a positive effect on the microstructure and mechanical properties of the AA7075 alloy compared to the reference sample. Especially as a result of the heat treatments at 100 °C, higher results were obtained in hardness and compression strength compared to the initial values. [ABSTRACT FROM AUTHOR]

The corrosion behavior and microstructure of a novel multicomponent Al75Mg5Li10Zn5Cu5 low entropy alloy (Al LEA) were investigated in different Cl− ion concentrations of acidic (HCl), neutral (NaCl), and alkaline (NaOH) media. The study was performed by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) methods. The surface morphologies and chemical composition were examined by using a scanning electron microscope with energy‐dispersive X‐ray spectroscopy. The results indicated that with the increase of the Cl− ion concentrations, the degradation rate with more pits and cracks was observed in both acidic and neutral media. This is due to the breakdown of Al(OH)3/Al2O3 passive layer. In an alkaline medium, increasing of pH value from pH 8 to pH 12, there was a slight increment in corrosion rate (CR). However, the corrosion trend was not witnessed on alloy surfaces because of the formation of Mg32(Al, Zn)49 and AlCu phases, which are more stable than α‐Al. The order of Al‐LEA CR is found to be HCl > NaCl > NaOH. The results obtained from the polarization and EIS were in good agreement with each other. [ABSTRACT FROM AUTHOR]

The La 0.8- x Pr x Mg 0.2 Ni 3.8 (x = 0, 0.05, 0.1, 0.2, 0.3) alloy were synthesized useing the induction melting method. X-ray diffraction, scanning electron microscope, electron probe micro analyzer, and electrochemical tests were used to analyze the structure and electrochemical performance of the La 0.8- x Pr x Mg 0.2 Ni 3.8 (x = 0–0.3) alloy. It was studied how the Pr element affected the electrochemical characteristics and microstructure of the A 5 B 19 La-Mg-Ni based hydrogen storage alloy. The results show that the alloy consists of the CaCu 5 -LaNi 5 phase, 2 H-Pr 5 Co 19 phase, and 3R-Ce 5 Co 19 phase. The abundance of the A 5 B 19 phase increase with the increase of Pr content, while the abundance of the LaNi 5 phase decrease, and the addition of Pr promotes the formation of the 2 H-Pr 5 Co 19 phase. According to the results of the electrochemical test, every sample has good activation qualities, and the activation can be completed in 3–4 times. The activation properties are not significantly altered by the addition of Pr. The maximum discharge capacity increases at first, then decreases, reaching the highest 371.15 mAh g−1 at x = 0.2. The cyclic stability gradually improves with increasing content of Pr, and the maximum capacity retention rate reaches 85.80 % after 100 cycles. The primary factor influencing the alloy's high rate discharge ability is the exchange current density. With the increase of the exchange current density, the high rate discharge performance is gradually enhanced. • The La-Mg-Ni based hydrogen storage alloy A 5 B 19 has better performance than AB 3 and A 2 B 7. • The hydrogen storage alloy was partially substituted by Pr element with higher electronegativity. • The addition of Pr significantly improves the phase structure stability and cycle stability of the alloy. • The corrosion and oxidation of the alloy electrode during the cycle are improved. [ABSTRACT FROM AUTHOR]

The effects of La and Y on the microstructure and mechanical properties of cast Al-Si-Cu alloys were investigated by X-ray diffractometer (XRD), optical microscope (OM), and scanning electron microscope (SEM). The results indicated that the addition of La and Y had a great effect on the refinement of α-Al grains, the modification of eutectic Si phase, and the reduction of β-Al5FeSi length in Al-Si-Cu alloys. The A380 + 0.6 wt.% La/Y alloy exhibited the best microstructure and mechanical properties. The UTS and EI of the A380 + 0.6 wt.% La/Y alloy were 215.3 MPa and 5.1%, which were 22.9% and 37.8% higher than those of the matrix alloy, respectively. In addition, neither Al11La3 nor Al3Y generated by the addition of La and Y could not serve as the nucleation core of α-Al grains, so the grain refinement of α-Al originated from the growth limitation and constitutional supercooling. Since La and Y promote twinning generation and constitutional supercooling, the eutectic Si phase also changed from stripe-like to short fibrous or even granular and was significantly refined. Furthermore, thermodynamic calculations indicated that the Al11La3 phase was formed first and the Al3Y phase was generated on the Al11La3 phase. [ABSTRACT FROM AUTHOR]

The deformation aspects associated with the micro-mechanical properties of the powder laser bed fusion (P-LBF) additively manufactured stainless steel 316L were investigated in the present work. Toward that, micro-pillars were fabricated on different planes of the stainless steel 316L specimen with respect to build direction, and an in situ compression was carried out inside the chamber of the scanning electron microscope (SEM). The results were compared against the compositionally similar stainless steel 316L, which was fabricated by a conventional method, that is, casting. The post-deformed micro-pillars on the both materials were examined by electron microscopy. The P-LBF processed steel exhibits equiaxed as well as elongated grains of different orientation with the characteristics of the melt-pool type arrangements. In contrast, the cast alloy shows typical circular-type grains in the presence of micro-twins. The yield stress and ultimate compressive stress of P-LBF fabricated steel were about 431.02 ± 15.51 − 474.44 ± 23.49 MPa and 547.78 ± 29.58 − 682.59 ± 21.59 MPa, respectively. Whereas for the cast alloy, it was about 322.38 ± 19.78 MPa and 477.11 ± 25.31 MPa, respectively. Thus, the outcome of this study signifies that the AM-processed samples possess higher mechanical properties than conventionally processed alloy of similar composition. Irrespective of the processing method, both specimens exhibit ductile-type deformation, which is typical for metallic alloys. [ABSTRACT FROM AUTHOR]

Purpose: FeNi36 (Invar-36) alloy is widely used in the fabrication of molding tools in aerospace industries but there remains a need to improve its wear and friction performance due to its relatively low hardness. The formation of a heat affected zone (HAZ) on the surface of Invar-36 cut by wire electric discharge machining (WEDM) is promising to enhance its tribological properties. This study aims to investigate the tribological performance of WEDM-treated Invar-36 via a ball-on-disk tribometer in dry-sliding conditions. Design/methodology/approach: The untreated and WEDM-treated Invar-36 surfaces were reciprocated against an alumina ball at a sliding velocity of 40 mm/s, a stroke length of 10 mm and a sliding duration of 125 min under loads of 5, 10 and 20 N. The worn surfaces were characterized using a 2D profilometry and a scanning electron microscope equipped with energy-dispersive spectroscopy. Findings: The results showed that the WEDM-treated surface had a superior friction coefficient and wear resistance in comparison to the untreated surface, due to the grown HAZ. There was found to be a 9.3%–11.4% decrease in the friction coefficient and a 47%–57% reduction in the wear volume after the WEDM treatment. Both the untreated and WEDM-treated Invar-36 surfaces found abrasion and plastic deformation as the dominant wear mechanisms. Originality/value: Previous works have not focused on the tribological performance of the WEDM-treated Invar-36 extensively used for molding tools in aerospace industries. Our findings provide compelling evidence that the WEDM treatment improved the wear and friction performance of Invar-36 alloy because of the grown HAZ. [ABSTRACT FROM AUTHOR]

In this paper, Al0.6CoCrFeNi/5052 aluminum matrix composites were prepared at different sintering temperatures (550–700 °C) by vacuum hot-pressing sintering. The effects of sintering temperature on composites were studied by testing the morphology, phase composition and mechanical properties of the composites, which were characterized by uniaxial compression experiments, X-ray diffraction, scanning electron microscope, electron probe and nanoindentation. The results show that the prepared composites have high strength and very good ductility with sintering temperature lower than 700 °C. When the sintering temperature is above 550 °C, the interface layer is formed in the composite material. As the sintering temperature increases, the formation method of the interface layer changes. The generation of the interface layer has a significant effect on the mechanical properties of the composites. [ABSTRACT FROM AUTHOR]

The Mg-(4-x)Nd-xGd-0.3Sr-0.2Zn-0.4Zr (x = 0, 1, 2, and 3 wt%, Gd/Nd = 0, 1/3, 1, and 3) alloys were hot extruded and then aged (T5). The friction and wear properties of the as-extruded and as-aged alloys were studied using a ball-on-disk wear testing machine and a scanning electron microscope to reveal the impacts of the Gd/Nd ratio and aging treatment. The results show that the friction coefficient of the as-extruded alloys increases first and then decreases with increasing Gd/Nd ratio. After aging, the friction coefficient of the alloys decreases slightly. The Gd/Nd ratio has no significant effect on the wear rate of the as-extruded alloys, and the wear rate decreases first and then increases with the increase in the Gd/Nd ratio for the as-aged alloys. The T5 alloy with a Gd/Nd ratio of 1/3 has the best wear resistance. The wear mechanisms of alloys mainly include abrasive wear, oxidation wear, and delamination wear. [ABSTRACT FROM AUTHOR]

In this work, the influence of pulse frequency in the electric pulse treatment (EPT) on the wear and corrosion resistance of Al-4.5Mg-3Si alloy has been investigated by using a ring block friction tester, electrochemical workstation, stereo microscope, laser scanning confocal microscope, scanning electron microscope, and x-ray diffractometer. Results have shown that the hardness of samples with EPT significantly improved, and the volume of the Mg2Si phase was lower than those of the original sample. And the wear and corrosion resistance of Al-4.5Mg-3Si alloy was significantly improved by EPT. When the pulse frequency was 7 Hz, the maximum hardness was 77.100 HBS, and the volume fraction of the Mg2Si phase was reduced from 38.28 to 33.81%. The self-corrosion potential was increased from − 1.3241 to − 1.2764 V, self-corrosion current density was reduced from 1.2726 × 10−5 to 1.0048 × 10−5 A/cm2, and the lowest average corrosion rate was 113.10 g/m2 h. [ABSTRACT FROM AUTHOR]

The present study successfully demonstrates the fabrication of a novel class of high-entropy alloy, namely Nb17Zr33Ti17W33, through suspension melting and casting technique. To investigate the dynamic mechanical behavior and energy release effects of the alloy under high-speed impact loads, various techniques were employed, including split Hopkinson pressure bar (SHPB), X-ray diffractometer (XRD), scanning electron microscope (SEM), and high-speed photography. These methods were utilized to acquire crucial data, such as crystal structure analysis, stress–strain curves, and microstructural examination of failed specimens. The modified Johnson–Cook (J-C) model was employed to elucidate the dynamic flow behavior of the alloy, while investigating the failure mechanism and energy release phenomenon during the process of dynamic compression. The experimental results demonstrate that the alloy material exhibits a dual-phase (BCC1 + BCC2) structure, exhibiting ductile fracture behavior under dynamic compression conditions. On the fracture surface, typical dimple structures along with evidence of shear slip and melting traces were observed, indicating an energy-releasing failure process. The newly developed alloy exhibited exceptional strength, high density, remarkable plasticity, and outstanding energy release properties, rendering it highly promising for applications under extreme loads. [ABSTRACT FROM AUTHOR]

Hot-dip aluminum alloy is widely used in the engineering fields. However, during the aluminum plating process, Fe inevitably enters and reaches a saturation state, which has a significant impact on the corrosion resistance and microstructure of the coating. Currently, adding Si during the hot-dip aluminum process can effectively improve the quality of the coating and inhibit the Fe-Al reaction. To understand the effect of Si content on the microstructure and electrochemical performance of Al-xSi-3.5Fe coating alloys, the microstructure and post-corrosion morphology of the alloys were analyzed using SEM (Scanning Electron Microscope) and XRD (X-ray Diffraction). Through electrochemical tests and complete immersion corrosion experiments, the corrosion resistance of the coating alloys in 3.5 wt.% NaCl was tested and analyzed. The results show that the Al-3.5Fe coating alloy mainly comprises α-Al, Al3Fe, and Al6Fe. With the increase in Si addition, the iron-rich phase changes from Al3Fe and Al6Fe to Al8Fe2Si. When the Si content reaches 4 wt.%, the iron-rich phase is Al9Fe2Si2, and the excess Si forms the eutectic Si phase with the aluminum matrix. Through SKPFM (Scanning Kelvin Probe Force Microscopy) testing, it was determined that the electrode potentials of the alloy phases Al3Fe, Al6Fe, Al8Fe2Si, Al9Fe2Si2, and eutectic Si phase were higher than that of α-Al, acting as cathode phases to the micro-galvanic cell with the aluminum matrix, and the corrosion form of alloys was mainly galvanic corrosion. With the addition of silicon, the electrode potential of the alloy increased first and then decreased, and the corrosion resistance results were synchronous with it. When the Si content is 10 wt.%, the alloy has the lowest electrode potential and the highest electrochemical activity. [ABSTRACT FROM AUTHOR]

The low strength caused by the single FCC structure of the CrMnFeCoNi high entropy alloy (HEA) limits its application in the field of coating. Here, we prepared high-entropy alloy coatings of CrMnFeCoNi with different ZrC contents on Q235 steel by a plasma transferred arc process. The effects of ZrC on the microstructure and properties of the CrMnFeCoNi HEA coating were investigated by optical microscopy, scanning electron microscope, and X-ray diffraction and by employing a potensiostat/galvanostat. The results showed that ZrC mainly existed in the coatings as a second phase, having little influence on the main crystal structure and micromorphology of the CrMnFeCoNi HEA coating. The hardness of the CrMnFeCoNi HEA coating increased with the ZrC content. ZrC can effectively improve the corrosion resistance of the CrMnFeCoNi HEA coating. In a 1 mol/L NaCl solution with 4 wt% ZrC, the annual corrosion rate was only 5.997% of that of the HEA coating. Nevertheless, the improvement in the wear resistance of CrMnFeCoNi high-entropy alloy coatings was not apparent with the addition of ZrC. Consequently, the addition of ZrC to the FeCoCrNiMn high-entropy alloy coating holds promise for applications in corrosion resistance, particularly in oceanic environments. [ABSTRACT FROM AUTHOR]

The effect of solo and combined addition of Al (3wt. %) and Zn (1wt. %) into gravity-cast Mg-10 wt. % Sn binary alloy on the dry sliding wear test has been investigated using pin-on-disk configuration with varying rotational speed (100 and 200 rpm) under a range of test loads (10, 20, 30, and 40 N). Microstructural characterization and phase analysis of the as-cast Mg-Sn alloys using scanning electron microscope and x-ray diffraction, respectively, have revealed the refinement of the binary alloy microstructure in terms of smaller dendritic arm spacing, uniform and discrete distribution of eutectic phase mixture at the interdendritic locations owing to the alloying additions. Moreover, a significant improvement in microhardness is achieved with increase in amount (wt.%) of alloying elements, depicting the highest hardness in the Mg-10Sn-3Al-1Zn (wt.%) alloy. Simultaneously, the alloying addition even in micro-concentration has been found to reduce the specific wear rate than that of the binary alloy over the entire loading range. The post-wear topographical surface features and chemical analysis using scanning electron microscope and energy-dispersive x-ray spectroscopy of the investigated alloys have suggested the oxidation and abrasion as dominant wear mechanisms. The reduced wear rates in the Al containing alloys are ascribed to the protective and continuous mechanically mixed oxide scale formation during test, which acts as a lubricating layer between the pin and the rotating disk. The discrete oxide island formation at the Zn-lean regions of Zn containing alloys is responsible for their accelerated wear rates. [ABSTRACT FROM AUTHOR]

The aim of this research is to assess the influence of Sn inclusion on the microstructure evolution and age-hardening response of a Zn-4Cu alloy. This is the first study to correlate the age-hardening response to the microstructure of Zn-4Cu alloy reinforced with different Sn contents. A series of Zn-4Cu-Sn alloys were successfully fabricated with different Sn concentrations in the range of 0.0–4.0 wt.% using permanent mold casting. The microstructure of Zn-4Cu-Sn alloys was investigated by means of a scanning electron microscope (SEM) attached with an energy dispersive spectroscope (EDS) and X-ray diffraction (XRD) line profile analysis. At room temperature, the Vickers microhardness measurements were used to assess the age-hardening response of alloys. The results show that the microhardness of the Zn-4Cu (ZC) binary alloy increases a little bit from 76 to 80 HV as the aging time increases from 2 to 128 h, respectively. For aging times up to 16 h, the microhardness of all Sn-containing alloys decreases but then increases again. The lowest hardness belongs to the ZC-1.5Sn alloy, and the Sn-Zn-3.0Sn alloy has the highest; the other alloys fall somewhere in between. At high aging times (64 and 128 h), the microhardness of all Sn-containing samples increased continuously with an increasing Sn content from 0.0 to 3.0 wt.%. When the Sn-containing alloys (3.5 and 4.0 wt.% Sn) were aged for 64 and 128 h, the hardness declined by 7.94% and 8.90% compared to their peak aging hardness values, respectively. By considering the structural changes that occur in the Zn-4Cu-Sn alloys, the reasons for the observed variations in microhardness data with increasing Sn content and aging time were elucidated. X-ray diffraction (XRD) data was analyzed to determine the zinc matrix's lattice parameters, c/a ratio, and unit cell volume variations. [ABSTRACT FROM AUTHOR]

The present study explores the preparation of Al–10wt.%Zn alloy by the casting process. Nano CuO was prepared by the Co-precipitation method. The effect of adding nanostructure of (1wt.% CuO) to Al–10Zn alloy was studied the corrosion effects as-cast and with different aging temperatures (423, 443, and 463 K) for 2 h in 3.5% NaCl aqueous solution after homogenized for 2 h at 500 K at room temperature. Electrochemical measurements (OCP, Tafel, and EIS) were performed to determine the corrosion rate (C.R.) and corrosion current density (Icorr.) to find out corrosion behavior. In addition, microstructures of Al–10Zn and Al–10Zn–1CuO were observed using a scanning electron microscope, EDX mapping, and the optical microscope to investigate the effect of the nanoparticle's addition before and after aging and the corrosion test. The average crystal size and the dislocation density were calculated from the XRD pattern. The results show that the appropriate addition of CuO nanoparticles can refine the Al–10Zn alloy and shift the Al–10Zn alloy to a more noble direction. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this study is to describe the mechanism of single-crystal high-temperature creep deformation, predict the creep life more accurately and study the creep constitutive and lifetime models with microstructure evolution. Design/methodology/approach: The mechanical properties of nickel-based single-crystal superalloy are closely related to the γ' phase. Creep tests under four different temperature and stress conditions were carried out. The relationship between creep temperature, stress and life is fitted by numerical method, and the creep activation energy is obtained. The creep fracture surface, morphology and evolution of strengthening phase (γ') and matrix phase (γ) during different creep periods were observed by scanning electron microscope. With the increase of creep temperature, the rafting time is advanced. The detailed morphology and evolution of dislocations were observed by transmission electron microscope (TEM). Findings: With the increase of creep temperature, the rafting time is advanced. The detailed morphology and evolution of dislocations were observed by TEM. Dislocations are mainly concentrated in the γ channel phase, especially at high temperature and low stress. Originality/value: A creep constitutive model based on the evolution of γ' phase size and γ channel width was proposed. Compared with the experimental results, the predicted creep life is within 1.4 times error dispersion band. [ABSTRACT FROM AUTHOR]