Search

The piezoelectric and dielectric properties of PMN-PT single crystals were significantly enhanced by alternating current electric field poling (ACP). In this work, to investigate the mechanisms of piezoelectric performance enhancement in relaxor ferroelectric single crystals by ACP, a [001]-oriented PIN-PMN-PT single crystal with a diameter of 3 in was grown by the modified Bridgman method, and a series of single crystal samples within 100 mm of the height of the crystal boule were prepared. Compared with their direct current electric field poling (DCP) counterparts, the electrical properties of single crystal samples at different heights by ACP were regularly enhanced. The piezoelectric coefficient d33 and the dielectric constant ɛ33 of the rhombohedral samples both increased by nearly 20%. Based on the results of polarized light microscopy, the domain wall in [001]-poled ACP samples could not be observed along the [001] direction. The brightness of polarized light propagating along the [010] orientation was enhanced after ACP. The domain images of {100} in the DCP and ACP samples were observed by piezoelectric force microscopy. The results showed that the domain size of ACP samples increased. The existence of layered domains can be clearly found in the scanning electron microscopy results of the stress fracture surface of the ACP sample. According to the analysis, the improvement of the piezoelectric performance in ACP samples comes from the elimination of the 71° domain walls. This work demonstrates that certain ACPs can regulate the domain structure and steadily improve the piezoelectric properties of R-phase PIN-PMN-PT single crystals. [ABSTRACT FROM AUTHOR]

The low uniformity in properties of relaxor ferroelectric crystals is a long‐standing issue in the ferroelectric community, which limits the available volume of the entire crystal boule. The aim of this study is to develop a relaxor ferroelectric crystal with improved property uniformity and excellent piezoelectricity. To this end, Pb(In1/2Nb1/2)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 is doped with Nd2O3 (Nd–PIN–PMN–PT) to improve the crystal performance. Along the crystal boule, the piezoelectric coefficient d33 varies from 2800 to 3500 pC N−1, and the dielectric constant ranges from 8400 to 9800, with variations of 25% and 16%, respectively. Such high property uniformity results in over 75% available volume of the crystal boule, compared to 30–50% for undoped crystals grown by Bridgman method. At the electric field of 1 kV cm−1, the converse piezoelectric response is up to 4780 pm V−1. In addition, its Curie temperature (TC) and coercive field (EC) are above 150 °C and 3 kV cm−1, respectively. Compared with Pb(Mg1/3Nb2/3)O3–PbTiO3 crystal (d33: 1500 pC N−1, TC: 135 °C, EC: 2.3 kV cm−1), the larger piezoelectricity, the higher TC and EC, and improved uniformity make Nd–PIN–PMN–PT crystals promising candidates for advanced piezoelectric applications. [ABSTRACT FROM AUTHOR]

The piezoelectric actuator is a kind of actuation device that acts through the inverse piezoelectric effect. Due to advantages of high precision, low power consumption, compact size, and flexible structure design, they have a wide range of applications in optics, robotics, microelectromechanical systems, and so on. Piezoelectric materials are the core materials for piezoelectric actuators. In this review, recent developments in high-performance piezoelectric materials (HPMs) are introduced, including relaxor ferroelectric crystals, textured ceramics, piezoelectric metamaterials, and so on. The advances of piezoelectric actuators are introduced in this review based on the developments of those piezoelectric materials, where the relationship between the figure of merits of materials and the performance of actuators is also discussed. Finally, we present outlooks and challenges for piezoelectric materials and actuators. [ABSTRACT FROM AUTHOR]

Traditional piezoelectric adaptive lenses (ALENS) are fabricated by piezoceramics with transparent liquids as the filling media. However, it is challenging to achieve high focal sensitivity and long-time robustness because of the low piezoelectricity of ceramics as well as the evaporation and leakage of the liquids. To overcome the above-mentioned issues, we design a piezoelectric lens based on a radial extension-arching mode by using polydimethylsiloxane films and Pb(In1/2Nb1/2)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 (PIMNT) relaxor ferroelectric single crystals to replace the transparent liquids and Pb(Zr, Ti)O3 (PZT) ceramics, respectively. Due to the ultrahigh piezoelectric properties (d33 ∼ 1500 pC N−1 and d31 ∼ 730 pC N−1) of the PIMNT crystals and the optimized radial extension-arching structure, an ultrahigh focal sensitivity (8.5 cm V−1 and a fast response time (∼102μs) is achieved, outperforming conventional ALENS based on piezoceramic actuators (∼103 μs and ∼10−1 cm V−1) and dielectric elastomer actuators (∼105 μs and ∼10−2 cm V−1). The largest output displacement of our designed ALENS is up to 53.6 μm at 4.2 kHz under 80 Vpp, and its focus is in the range of 57.44 cm to ∞. Furthermore, its performance remains unchanged after 4 × 107 vibration cycles, indicating its long-time robustness. This work sheds light on the design of advanced adaptive optical systems, where an ultrahigh focal sensitivity and a fast response are required. [ABSTRACT FROM AUTHOR]

Relaxor‐PbTiO3 crystals exhibit excellent piezoelectric properties (d33 > 2000 pC N−1 and k33 > 90%) and thus attractes widespread attention in the past two decades. However, the inevitable segregation of components during the crystal growth results in relatively low‐performance consistency of Pb(Mg1/3Nb2/3)O3‐PbTiO3 (PMN‐PT) crystals, which seriously affects their practical applications. In this work, Nd3+ as A‐site substitution is introduced to improve the uniformity of electromechanical performance of PMN‐PT crystal. The results show that the crystal exhibits a high piezoelectric coefficient of 3000 pC N−1 in rhombohedral phase with a variation of 36%. The electron probe X‐ray microanalyzer indicates that the opposite separation characteristics of Nd3+ and Ti4+ lead to improved uniformity of piezoelectric performance along the crystal boule. The giant piezoelectricity in Nd‐doped PMN‐PT is attributed to the enhanced local structural heterogeneity introduced by doping Nd. Furthermore, the Nd‐doped PMN‐PT crystal shows the rhombohedral‐tetragonal phase transition temperature in the range of 74–87 °C, which indicates that Nd‐doped PMN‐PT crystal can be a promising candidate for the design of advanced piezoelectric transducers. [ABSTRACT FROM AUTHOR]

Low driving voltage is important for miniaturization and untethered service of millirobots made of piezoelectric materials. In this research, we designed a bio-inspired bimorph-structured millirobot with a transparent relaxor ferroelectric crystal. Due to the ultrahigh piezoelectricity of the relaxor ferroelectric crystals and the optimized bimorph-based structure, the millirobot shows a maximum moving speed up to 9.22 b s−1 (body length per second) at 100 V, while the minimum driving voltage for initial movement can be as low as 3 V, which is more than two orders of magnitude smaller than that of millirobot based on dielectric elastomers. The maximum and minimum power consumptions of the millirobot are 71.6 mW and 85.9 μW, respectively. The robustness of the millirobot is reflected in its mechanical load stability carrying a 78 g mass (97.5 times of its weight) and its cryogenic tolerance. This work is believed to be beneficial to the design of various robust electromechanical devices with low driving voltage. [ABSTRACT FROM AUTHOR]

Alternating-current poling (AC-Poling) has attracted wide interests in enhancing piezoelectric performance of ferroelectric single crystals. However, the mechanism of phase transformations and domain morphology underlying AC-Poling has not been thoroughly investigated. In this work, we have systematically studied the AC-poling effect on domain structures and piezoelectric properties in the relaxor ferroelectric single crystals of 0.24Pb(In 1/2 Nb 1/2)O 3 –0.44Pb(Mg 1/3 Nb 2/3)O 3 –0.32PbTiO 3. It is shown that the piezoelectric constant (d 33) and permittivity (ε 33) are greatly enhanced via [001]-AC-poling compared to DC-poling, related to the presence of modified domain configurations as indicated previously. For [110]-oriented specimens, the piezoelectricity through AC-poling is only half as that for the DC-poled single crystals. We attribute this to the transition from the monoclinic-B phase to an orthorhombic phase under AC-poling, confirmed by synchrotron radiation X-ray diffraction and piezo-response force microscopy. The transition to the orthorhombic phase is likely a consequence of lower Gibbs energy. This study on orientation-dependent characteristics of AC-poling for PIN-PMN-PT single crystals will guide the development of AC-poling technology in applications. [Display omitted] [ABSTRACT FROM AUTHOR]

• Bending-bending mode piezoelectric actuator with crystal stacks are proposed and evaluated. • Ultrahigh piezoelectric coefficient d 33 of ~10,800 pC/N are achieved in actuation crystal stacks. • Due to high piezoelectricity and bending mode, max velocity is 3.28 mm/s under 130 V pp. • Minimum step resolution of 0.35 µm is demonstrated under 25 V pp driving voltage. [Display omitted] Piezoelectric actuators are important elements for compact actuations with high precision; however, driving voltage reduction is demanding for integration and minimization of precision actuations. In this work, we proposed a bending-bending mode piezoelectric actuator based on multilayered Pb(In 1/2 Nb 1/2)O 3 -Pb(Mg 1/3 Nb 2/3)O 3 -PbTiO 3 (PIN-PMN-PT) single crystals. Ultrahigh apparent piezoelectric coefficient d 33 of ~10,800 pC/N is achieved in four crystal stacks. The crystal stacks are used to fabricate bending-bending mode piezoelectric actuators to reduce driving voltage. Experimental results show that it can produce a maximum traveling velocity of 3.28 mm/s under the driving voltage of 130 V pp at 1000 Hz and minimum step resolution of 0.35 µm with 25 V pp driving voltage. Conventional piezoelectric actuators require driving voltage of ~300 V pp for similar motion velocity. This work demonstrates advantages of crystal stacks in piezoelectric actuators and potential applications in low-voltage precise actuations. [ABSTRACT FROM AUTHOR]