Search

Silicon photomultipliers (SiPMs) are solid-state, single-photon sensitive, pixelated sensors whose usage for scintillation detection has rapidly increased over the past decade. It is known that the avalanche process within the device, which renders a single photon detectable, can also generate secondary photons which may be detected by a separate device. This effect, known as external crosstalk, could potentially degrade the science goals of future xenon dark matter experiments. In this article, we measure the effect of external crosstalk in a dual-phase, liquid xenon time projection chamber fully instrumented with SiPMs. We then consider the implications for a future xenon dark matter experiment utilizing SiPMs and discuss possible solutions.

In the present work, the sintering of bismuth germanate through hot pressing and the improvement of scintillator performance were investigated. The linear shrinkage, crystalline structure, microstructure, transparency degree, and radioluminescence (RL) were studied as functions of the sintering pressure. X‐ray diffraction revealed that the samples were predominantly composed of the Bi4Ge3O12 phase, accompanied by small amounts of Bi12GeO20, with concentrations varying according to the sintering parameters. These concentrations were quantified through Rietveld refinement, which also indicated a tendency for the cell parameters to shrink as the sintering pressure increased. The microstructure of the ceramic pellets produced under varying hot‐pressing parameters was investigated using scanning electron microscopy (SEM), revealing that while the grain size was preserved, the porosity and grain boundary thickness were reduced by the hot pressing, forming a quasicontinuum in some areas of the sample. The RL of all the samples exhibited a green color, with a maximum at 540 nm, ascribed to the transitions from the 3P0,1,21P1 excited states to the fundamental 1S0 state of the Bi3+ ions. For samples sintered under a pressure of .18 MPa, the enhancement in the optical transmittance, accompanied by a 61.36% increase in light output at the maximum wavelength, was observed. [ABSTRACT FROM AUTHOR]

The zero-dimensional copper halide perovskite Cs 3 Cu 2 I 5 displays extraordinary luminescence and scintillation characteristics, and high-quality crystals are extremely desirable for exploring the commercial applications. Currently, the most critical issue in the solution growth of Cs 3 Cu 2 I 5 crystals is the easy oxidation of halides, which significantly hinders the optimization of crystal qualities. The hypophosphorous acid (H 3 PO 2) has been applied to inhibit the oxidation, nevertheless, the related mechanism is elusive and has been largely ignored. Herein, Cs 3 Cu 2 I 5 crystals have been grown from N, N-Dimethylformamide (DMF) solvent by the antisolvent vapor-assisted crystallization (AVC) method. It is verified that H 3 PO 2 effectively prevents the oxidation of Cs 3 Cu 2 I 5 by rapidly reducing Cu2+ and I 3 −, maintaining the stability of the precursor solution and continuously suppressing oxidation during the whole growth process. Meanwhile, by increasing the acidity of the solution, H 3 PO 2 dissolve precursor colloids and efficiently enhance the solubility of halides. Thus, the addition of H 3 PO 2 favors the rapid growth of centimeter-sized Cs 3 Cu 2 I 5 crystals with well-defined crystallographic planes within several days. As excellent gamma ray scintillator, the crystal exhibits high light yield of 38000 photons/MeV, with energy resolution of 5.6 % under 662 keV radiation from a 137Cs source. This work deeply elucidates new insight into the critical effect of H 3 PO 2 in the DMF based solution crystal growth, facilitating the preparation of large-size and high-performance copper halide perovskite crystals. [ABSTRACT FROM AUTHOR]

High-performance and low-cost metal halide perovskite scintillator materials have important applications in X-ray detection and imaging. However, large-sized perovskite scintillator panel with high transmittance, low toxicity and long-term stability is still lacking. Herein, Eu2+ doped cesium alkaline earth chloride nanocrystals (Eu2+: CsCaCl 3 , Eu2+: CsSrCl 3 , and Eu2+: Cs 2 BaCl 4 NCs) embedded in glasses through conventional melt-quenching and subsequent heat-treatment were developed. These NCs doped glasses exhibited highly efficient and narrowband photoluminescence in blue region. Benefitting from the large X-ray absorption coefficient and high photoluminescence quantum yied, these Eu2+: CsCaCl 3 NCs doped glass scintillator shows light yield of ∼9300 photons/MeV, detection limit of ∼213.8 μGy/s, and spatial resolution of 30.0 lp/mm. These results demonstrated that glasses containing Eu2+ doped cesium alkaline earth chloride nanocrystals are promising for X-ray detection and imaging. [ABSTRACT FROM AUTHOR]

In time-of-flight positron emission tomography (TOF-PET), a coincidence time resolution (CTR) below 100 ps reduces the angular coverage requirements and, thus, the geometric constraints of the scanner design. Among other possibilities, this opens the possibility of using flat-panel PET detectors. Such a design would be more cost-accessible and compact and allow for a higher degree of modularity than a conventional ring scanner. However, achieving adequate CTR is a considerable challenge and requires improvements at every level of detection. Based on recent results in the ongoing development of optimised TOF-PET photodetectors and electronics, we expect that within a few years, a CTR of about 75 ps will be be achievable at the system level. In this work, flat-panel scanners with four panels and various design parameters were simulated, assessed and compared to a reference scanner based on the Siemens Biograph Vision using NEMA NU 2-2018 metrics. Point sources were also simulated, and a method for evaluating spatial resolution that is more appropriate for flat-panel geometry is presented. We also studied the effects of crystal readout strategies, comparing single-crystal and module readout levels. The results demonstrate that with a CTR below 100 ps, a flat-panel scanner can achieve image quality comparable to that of a reference clinical scanner, with considerable savings in scintillator material. [ABSTRACT FROM AUTHOR]

Ultra‐high‐speed synchrotron‐based hard X‐ray (i.e. above 10 keV) imaging is gaining a growing interest in a number of scientific domains for tracking non‐repeatable dynamic phenomena at spatio‐temporal microscales. This work describes an optimized indirect X‐ray imaging microscope designed to achieve high performance at micrometre pixel size and megahertz acquisition speed. The entire detector optical arrangement has an improved sensitivity within the near‐ultraviolet (NUV) part of the emitted spectrum (i.e. 310–430 nm wavelength). When combined with a single‐crystal fast‐decay scintillator, such as LYSO:Ce (Lu2−xYxSiO5:Ce), it exploits the potential of the NUV light‐emitting scintillators. The indirect arrangement of the detector makes it suitable for high‐dose applications that require high‐energy illumination. This allows for synchrotron single‐bunch hard X‐ray imaging to be performed with improved true spatial resolution, as herein exemplified through pulsed wire explosion and superheated near‐nozzle gasoline injection experiments at a pixel size of 3.2 µm, acquisition rates up to 1.4 MHz and effective exposure time down to 60 ps. [ABSTRACT FROM AUTHOR]

X-ray excited radioluminescence was demonstrated in Pr-doped lithium niobate polycrystalline samples with varying lithium-to-niobium ratios (R LN). The samples' phase structures, excitation and emission spectra, and radioluminescence were experimentally analyzed to investigate the tuning effects of R LN. Theoretical calculations based on Density Functional Theory (DFT) were conducted to elucidate the underlying mechanisms, and thermoluminescence curves were measured to verify the predictions of the theoretical analysis. We suggest that both photoluminescence and radioluminescence properties can be effectively tailored by adjusting the crystal structure, as well as the depth and density of electron traps within the LiNbO 3 :Pr matrix through R LN modulation. This research contributes to the development and practical implementation of scintillation materials derived from rare-earth-doped lithium niobate. [ABSTRACT FROM AUTHOR]

Objective: Positron Emission Tomography (PET) is a well-known imaging technology for the diagnosis, treatment, and monitoring of several diseases. Most PET scanners use a Ring-Shaped Detector Configuration (RSDC), which helps obtain homogeneous image quality but are restricted to an invariable Field-of-View (FOV), scarce spatial resolution, and low sensitivity. Alternatively, few PET systems use Open Detector Configurations (ODC) to permit an accessible FOV adaptable to different target sizes, thus optimizing sensitivity. Yet, to compensate the lack of angular coverage in ODC-PET, developing a detector with high-timing performance is mandatory to enable Time-of-Flight (TOF) techniques during reconstruction. The main goal of this work is to provide a proof of concept PET scanner appropriate for constructing the new generation of ODC-PET suitable for biopsy guidance and clinical intervention during acquisition. The designed detector has to be compact and robust, and its requirements in terms of performance are spatial and time resolutions < 2 mm and < 200 ps, respectively. Methods: The present work includes a simulation study of an ODC-PET based on 2-panels with variable distance. The image quality (IQ) and Derenzo phantoms have been simulated and evaluated. The phantom simulations have also been performed using a ring-shaped PET for comparison purposes of the ODC approach with conventional systems. Then, an experimental evaluation of a prototype detector that has been designed following the simulation results is presented. This study focused on tuning the ASIC parameters and evaluating the scintillator surface treatment (ESR and TiO2), and configuration that yields the best Coincidence Time Resolution (CTR). Moreover, the scalability of the prototype to a module of 64 × 64mm2 and its preliminary evaluation regarding pixel identification are provided. Results: The simulation results reported sensitivity (%) values at the center of the FOV of 1.96, 1.63, and 1.18 for panel distances of 200, 250, and 300 mm, respectively. The IQ reconstructed image reported good uniformity (87%) and optimal CRC values, and the Derenzo phantom reconstruction suggests a system resolution of 1.6–2 mm. The experimental results demonstrate that using TiO2 coating yielded better detector performance than ESR. Acquired data was filtered by applying an energy window of ± 30% at the photopeak level. After filtering, best CTR of 230 ± 2 ps was achieved for an 8 × 8 LYSO pixel block with 2 × 2 × 12mm3 each. The detector performance remained constant after scaling-up the prototype to a module of 64 × 64mm2, and the flood map demonstrates the module's capabilities to distinguish the small pixels; thus, a spatial resolution < 2 mm (pixel size) is achieved. Conclusions: The simulated results of this biplanar scanner show high performance in terms of image quality and sensitivity. These results are comparable to state-of-the-art PET technology and, demonstrate that including TOF information minimizes the image artifacts due to the lack of angular projections. The experimental results concluded that using TiO2 coating provide the best performance. The results suggest that this scanner may be suitable for organ study, breast, prostate, or cardiac applications, with good uniformity and CRC. [ABSTRACT FROM AUTHOR]

In this study, we propose novel three-layer composite scintillators designed for the simultaneous detection of different ionizing radiation components. These scintillators are based on epitaxial structures of LuAG and YAG garnets, doped with Ce3+ and Sc3+ ions. Samples of these composite scintillators, containing YAG:Ce and LuAG:Ce single crystalline films with different thicknesses and LuAG:Sc single crystal substrates, were grown using the liquid phase epitaxy method from melt solutions based on PbO-B2O3 fluxes. The scintillation properties of the proposed composites, YAG:Ce film/LuAG:Sc film/LuAG:Ce crystal and YAG:Ce film/LuAG:Ce film/LuAG:Sc crystal, were investigated under excitation by radiation with α-particles from a 239Pu source, β-particles from 90Sr sources and γ-rays from a 137Cs source. Considering the properties of the mentioned composite scintillators, special attention was paid to the ability of simultaneous separation of the different components of mixed ionizing radiation containing the mentioned particles and quanta using scintillation decay kinetics. The differences in scintillation decay curves under α- and β-particle and γ-ray excitations were characterized using figure of merit (FOM) values at various scintillation decay intensity levels (1/e, 0.1, 0.05, 0.01). [ABSTRACT FROM AUTHOR]

The study of scintillation-causing ionospheric irregularities is important to mitigate their effects on satellite communications. It is also important due to the spatial and temporal variability of these irregularities, given that their characteristics differ from one region to another. This study investigates the spatial and temporal characteristics of L1 amplitude scintillation-causing ionospheric irregularities over the Eastern Arabian Peninsula during the ascending phase of solar cycle 25 (years 2020–2023). The temporal occurrences of weak and strong scintillation were separated by sunset, with weak scintillation observed predominantly pre-sunset during the winter solstice and strong scintillation observed mainly post-sunset during the autumnal equinox. Strong scintillation was much more pronounced in 2023 compared to the other three years, indicating a strong influence of solar activity. Spatially, weak-scintillation-causing irregularities exhibited a wide distribution in azimuth and elevation, while strong-scintillation-causing irregularities were concentrated southwards. The combined analysis of S4 and rate of total electron content index (ROTI) suggested that small-scale ionospheric irregularities were present in both pre- and post-sunset periods, while large-scale irregularities were only seen during the post-sunset period. Furthermore, the presence of southward traveling ionospheric disturbances (TIDs) during the 2023 autumnal equinox was confirmed with the total electron content anomaly (Δ TEC), while the Ionospheric Bubble Index (IBI) provided by the Swarm mission was unable to confirm the presence of equatorial plasma bubbles during the same period. Observations from the FORMOSAT-7/COSMIC-2 mission indicated that strong-scintillation-causing irregularities were more prevalent under the F2-layer peak, while the weak-scintillation-causing irregularities were mostly observed at the E-layer, F2-layer, and above the F2-layer. This study aims to contribute insights into the behavior of scintillation-causing ionospheric irregularities in the region, with implications for future research during the peak of the 25th solar cycle. [ABSTRACT FROM AUTHOR]

The prevalent use of unsustainable polymers in current X‐ray scintillators poses a significant environmental concern. The advancement of biodegradable X‐ray scintillators holds promise in mitigating escalating environmental issues tied to electronic or medical waste and carbon footprints. Herein, a biodegradable and flexible X‐ray scintillation film is presented employing lead‐free 0D Cs3Cu2I5 perovskite nanoparticles integrated into densified‐delignified wood (Cs3Cu2I5@D‐Wood). The Cs3Cu2I5@D‐Wood film demonstrates precise and detailed X‐ray imaging capabilities, achieving a high spatial resolution of 10 line pairs per millimeter (lp·mm−1). To minimize the environmental impact associated with disposal, metal and halide ions (e.g., Cs+, Cu+, I−) from Cs3Cu2I5@D‐Wood can be easily retrieved by a simple solvent extraction process. The approach showcases the potential of biodegradable wood‐based X‐ray scintillation screens as alternatives to conventional, plastic‐based screens. This offers a significant contribution to environmental sustainability by reducing electronic or medical waste. [ABSTRACT FROM AUTHOR]

The aim of this study was to experimentally assess the luminescence efficiency of a cerium fluoride (CeF3) inorganic scintillator in crystal form as a possible alternative to high-luminescence but hygroscopic cerium bromide (CeBr3). The experiments were performed under typical diagnostic radiology X-rays (50–140 kVp). Parameters such as the crystal's absolute luminescence efficiency (AE) and the spectral matching with a series of optical detectors were examined. The replacement of bromine with fluorine appeared to drastically reduce the AE of CeF3 compared to CeBr3 and other commercially available inorganic scintillators such as bismuth germanate (Bi4Ge3O12-BGO). CeF3 reaches a maximum luminescence efficiency value of only 0.8334 efficiency units (EUs) at 140 kVp, whereas the corresponding values for CeBr3 and BGO were 29.49 and 3.41, respectively. Furthermore, the emission maximum (at around 313 nm) moved towards the lower part of the visible spectrum, making CeF3 suitable for spectral coupling with various photocathodes and photomultipliers applied in nuclear medicine detectors, but completely unsuitable for spectral matching with CCDs and CMOS. The obtained luminescence efficiency results denote that CeF3 cannot be applied in medical imaging applications covering the range 50–140 kVp; however, examination of its luminescence output in the nuclear medicine energy range (~70 to 511 keV) could reveal possible applicability in these modalities. [ABSTRACT FROM AUTHOR]

Neutrons are widely used in national defense, security, and medical health fields. It is critical to realize neutron detection with high efficiency. The most popular neutron detection scintillators such as lithium glass and 6LiF/ZnS:Ag screen exhibit insurmountable limitations: the former usually has relatively rather low light yield and latter is opaque. In this research, we report the successful construction of the novel full inorganic composite scintillators by low temperature co‐firing technology. The composite scintillator is derived from the ZnS:Ag and borate glass matrix, and it shows better transparency compared with the standard 6LiF/ZnS:Ag screen. It exhibits excellent scintillation properties with the X‐ray induced emission intensity of these composite scintillators reaching approximately 2.46 times of the standard Bi4Ge3O12 (BGO) crystal. The light output under thermal neutron excitation can reach 75 000 photons/neutron. In addition, it presents excellent neutron detection performance with natural abundance of 10B isotope. Our research findings can serve as a valuable reference for the advancement of robust neutron detection materials, particularly in the domain of ZnS:Ag‐based full inorganic scintillator for neutron detection. [ABSTRACT FROM AUTHOR]

Dense and transparent ceramic samples of a (Gd,Y)3Al2Ga3O12:Ce scintillator were obtained by using stereolithography-based Digital Light Processing (DLP) 3D printing for compacting, subsequent burnout, and pressureless sintering. The effects of stoichiometric deviations and green body compaction methods (uniaxial pressing versus DLP 3D printing) on the optical, luminescent, and scintillation properties of ceramics were analyzed. An excess of Y and Gd in the composition led to an increase in transmittance and to the acceleration of the scintillation kinetics. Moreover, transparent ceramics made of 3D-printed green bodies were found to be superior in light yield to the samples, which were prepared from the same powders and densified by uniaxial pressing. [ABSTRACT FROM AUTHOR]

Inverse beta decay (IBD) in plastic scintillators is one of the most commonly used methods for detecting reactor antineutrinos. Cosmic muon signals due to the IBD compared to those generated by antineutrinos are still the main challenge in these types of detectors. The IRAND (IRan ANtineutrino Detector) is currently being designed and implemented with the constraint of reducing the required hardware, and at the same time, improving the antineutrino detection efficiency. Imbalanced classification is one of the software methods in machine learning that deals with imbalanced data, such as muon and antineutrino. Using the IRAND-Sim simulation package based on the Geant4 toolkit presented in our previous research, the spectra and angular distribution of antineutrinos and muons can be calculated. However, in this study, the memory management techniques to handle the dataset due to a large number of muons have been used, and also two separate methods have been used in the imbalanced classification for discriminating muon and antineutrino events. The results show that this approach by combining real and simulated data is very efficient, and the imbalanced nature can be reduced to achieve better classifier performance. [ABSTRACT FROM AUTHOR]

Purpose: This study investigated the potential of a commercially available plastic scintillator, the Exradin W2, as a real‐time dosimeter for ultra‐high‐dose‐rate (UHDR) electron beams. This work aimed to characterize this system's performance under UHDR conditions and addressed limitations inherent to other conventional dosimetry systems. Methods and materials: We assessed the W2's performance as a UHDR electron dosimeter using a 16 MeV UHDR electron beam from the FLASH research extension (FLEX) system. Additionally, the vendor provided a beta firmware upgrade to better handle the processing of the high signal generated in the UHDR environment. We evaluated the W2 regarding dose‐per‐pulse, pulse repetition rate, charge versus distance, and pulse linearity. Absorbed dose measurements were compared against those from a plane‐parallel ionization chamber, optically stimulated luminescent dosimeters and radiochromic film. Results: We observed that the 1 × 1 mm W2 scintillator with the MAX SD was more suitable for UHDR dosimetry compared to the 1 × 3 mm W2 scintillator, capable of matching film measurements within 2% accuracy for dose‐per‐pulse up to 3.6 Gy/pulse. The W2 accurately ascertained the inverse square relationship regarding charge versus virtual source distance with R2 of ∼1.00 for all channels. Pulse linearity was accurately measured with the W2, demonstrating a proportional response to the delivered pulse number. There was no discernible impact on the measured charge of the W2 when switching between the available repetition rates of the FLEX system (18–180 pulses/s), solidifying consistent beam output across pulse frequencies. Conclusions: This study tested a commercial plastic scintillator detector in a UHDR electron beam, paving the way for its potential use as a real‐time, patient‐specific dosimetry tool for future FLASH radiotherapy treatments. Further research is warranted to test and improve the signal processing of the W2 dosimetry system to accurately measure in UHDR environments using exceedingly high dose‐per‐pulse and pulse numbers. [ABSTRACT FROM AUTHOR]

Background: The application of semi-conductor detectors such as cadmium–zinc–telluride (CZT) in nuclear medicine improves extrinsic energy resolution and count sensitivity due to the direct conversion of gamma photons into electric signals. A 3D-ring pixelated CZT system named StarGuide was recently developed and implemented by GE HealthCare for SPECT acquisition. The system consists of 12 detector columns with seven modules of 16 × 16 CZT pixelated crystals, each with an integrated parallel-hole tungsten collimator. The axial coverage is 27.5 cm. The detector thickness is 7.25 mm, which allows acquisitions in the energy range [40–279] keV. Since there is currently no performance characterization specific to 3D-ring CZT SPECT systems, the National Electrical Manufacturers Association (NEMA) NU 1-2018 clinical standard can be tailored to these cameras. The aim of this study was to evaluate the performance of the SPECT/CT StarGuide system according to the NEMA NU 1-2018 clinical standard specifically adapted to characterize the new 3D-ring CZT. Results: Due to the integrated collimator, the system geometry and the pixelated nature of the detector, some NEMA tests have been adapted to the features of the system. The extrinsic measured energy resolution was about 5–6% for the tested isotopes (99mTc, 123I and 57Co); the maximum count rate was 760 kcps and the observed count rate at 20% loss was 917 kcps. The system spatial resolution in air extrapolated at 10 cm with 99mTc was 7.2 mm, while the SPECT spatial resolutions with scatter were 4.2, 3.7 and 3.6 mm in a central, radial and tangential direction respectively. Single head sensitivity value for 99mTc was 97 cps/MBq; with 12 detector columns, the system volumetric sensitivity reached 520 kcps MBq−1 cc−1. Conclusions: The performance tests of the StarGuide can be performed according to the NEMA NU 1-2018 standard with some adaptations. The system has shown promising results, particularly in terms of energy resolution, spatial resolution and volumetric sensitivity, potentially leading to higher quality clinical images. [ABSTRACT FROM AUTHOR]

The ability to distinguish multiple forms of plutonium from one another, such as oxide and metal, is paramount in areas of nuclear nonproliferation and international safeguards. In its metal form, plutonium can be readily used in a nuclear weapon, while oxide forms are associated with nuclear reactor fuel. Oxide-based plutonium forms emit neutrons with an energy spectrum that is significantly different from the fission neutrons that are emitted from plutonium metal. Organic scintillation detectors output pulses that are proportional to the neutron energy deposited, and therefore present a means of distinguishing these plutonium forms based on their energy spectra. In this work, metal and oxide forms of plutonium were measured using a handheld detection system based on an organic glass scintillator. Monte Carlo modeling of these experiments was performed to provide insight into the origin of the features in the observed light output spectra. Through analysis of multiple regions of these spectra, in a matter of minutes we were able to unambiguously discriminate oxide and metal plutonium forms from one another and from a plutonium-beryllium neutron source, which was considered for comparison because these sources are commonly used in industrial applications. The ability to discriminate weapons-usable material from nuclear reactor fuel has applications in nuclear treaty verification and safeguards. [ABSTRACT FROM AUTHOR]

Rare earth ions with d-f transitions (Ce3+, Eu2+) have emerged as promising candidates for electroluminescence applications due to their abundant emission spectra, high light conversion efficiency, and excellent stability. However, directly injecting charge into 4f orbitals remains a significant challenge, resulting in unsatisfied external quantum efficiency and high operating voltage in rare earth light-emitting diodes. Herein, we propose a scheme to solve the difficulty by utilizing the energy transfer process. X-ray photoelectron spectroscopy and transient absorption spectra suggest that the Cs3CeI6 luminescence process is primarily driven by the energy transfer from the I2-based self-trapped exciton to the Ce-based Frenkel exciton. Furthermore, energy transfer efficiency is largely improved by enhancing the spectra overlap between the self-trapped exciton emission and the Ce-based Frenkel exciton excitation. When implemented as an active layer in light-emitting diodes, they show the maximum brightness and external quantum efficiency of 1073 cd m−2 and 7.9%, respectively. Rare-earth metal halide perovskites are promising for deep blue LEDs. Here, Yang et al. report energy transfer between self-trapped exciton and Frenkel exciton in Cs3CeI6 by adding excess CsI during thermal evaporation, resulting in deep blue LEDs with external quantum efficiency of 7.9% at 424 nm. [ABSTRACT FROM AUTHOR]

Silicon photomultipliers (SiPMs) are solid-state single-photon-sensitive detectors that show excellent performance in a wide range of applications. In FBK (Trento, Italy), we developed a position-sensitive SiPM technology, called "linearly graded" (LG-SiPM), which is based on an avalanche-current weighted-partitioning approach. It shows position reconstruction resolution below 250 μm on an 8 × 8 mm2 device area with four readout channels and minimal distortions. A recent development in terms of LG-SIPM is a larger chip version (10 × 10 mm2) based on FBK NUV-HD technology (near-ultraviolet sensitive), with a peak photon detection efficiency at 420 nm. Such a large-area detector with position sensitivity is very interesting in applications like MR-compatible PET, high-energy physics experiments, and readout of time-projection chambers, gamma and beta cameras, or scintillating fibers, with a reduced number of channels. These SiPMs were characterized in terms of noise, photon detection efficiency, and position resolution. We also developed tiles of 2 × 2 and 3 × 3 LG-SiPMs, reaching very large sensitive areas of 20 × 20 mm2 and 30 × 30 mm2. We implemented a "smart-channel" configuration, which allowed us to have just six output channels for the 2 × 2 elements and eight channels for the 3 × 3 element tiles, preserving a position resolution below 0.5 mm. These kinds of detectors provide a great advantage in compact and low-power applications by maintaining position sensitivity over large areas with a small number of channels. [ABSTRACT FROM AUTHOR]

We report the photon (PL), electron (CL) and X-ray (XEL) induced luminescence characteristics of high aspect ratio ultra-long (~ 50 µm) ZnO nanorods (NRs) and discuss the potential for fast X-ray detection based on the consistent and efficient visible emission (~ 580 nm) from ZnO NRs. Nanostructured ZnO scintillators were rearranged to form a vertically well-aligned NR design in order to help light absorption and coupling resulting in luminescent and fast scintillation properties. The design of the nanorod array combines the key advantages of a low-cost growth technique together with environmentally friendly and widely available materials. A low temperature hydrothermal method was adopted to grow ZnO NRs in one cycle growth and their structural, optical and X-ray scintillation properties were investigated. The relatively short (~ 10 µm) ZnO NRs emitting in the near-band-edge region were found to be almost insensitive to X-rays. On the other hand, the higher XEL response of long ZnO NRs, which is a key parameter for evaluation of materials to be used as scintillators for high quality X-ray detection and imaging, along with a decay time response in the order of ns confirmed promising scintillation properties for fast and high-resolution X-ray detector applications. [ABSTRACT FROM AUTHOR]

The high durability under harsh environment including high temperature, high humidity, and high radiation is required for scintillators used for decommissioning of nuclear facilities and radiation monitoring in nuclear fusion reactors. α‐SiAlON ceramics are highly potential for such scintillators because of their thermal and mechanical durability and luminescence corresponding to doped rare‐earth ion. In this study, scintillation properties of transparent Lu‐α‐SiAlON:Ce3+ ceramics were investigated for the first time. Lu‐α‐SiAlON:Ce3+ showed the scintillation responses to α‐rays and X‐rays. The α‐rays‐induced scintillation decay curve consists of two components whose decay time are 48 and 652 ns. The faster decay component most presumably results from 4f‐5d transition of Ce3+, whereas the origin of the slower one is unclear but may be defects in α‐SiAlON. The light yield of the Lu‐α‐SiAlON:Ce3+ ceramics was 1300 photons 5.5 MeV−1. [ABSTRACT FROM AUTHOR]

The GNSS-based bistatic SAR (GNSS-BSAR) system has emerged as a hotspot due to its low power consumption, nice concealment, and worldwide reach. However, the weak landing power density of the GNSS signal often necessitates prolonged integration to achieve an adequate signal-to-noise ratio (SNR). In this case, the effects of the receiver's time-frequency errors and atmospheric disturbances are significant and cannot be ignored. Therefore, we propose an ionospheric scintillation compensation-based imaging scheme for dual-channel GNSS-BSAR system. This strategy first extracts the reference phase, which contains the ionospheric phase scintillation and other errors. Subsequently, the azimuth phase of the target is divided into difference phase and reference phase. We apply the two-step phase compensation to eliminate Doppler phase errors, thus achieving precise focusing of SAR images. Three sets of experiments using the GPS L5 signal as the illuminator were conducted, coherently processing a 1.5 km by 0.8 km scene about 300 s. The comparative results show that the proposed method exhibited better focusing performance, avoiding the practical challenges encountered by traditional autofocus algorithms. Additionally, ionospheric phase scintillation extracted at different times of the day suggest diurnal variations, preliminary illustrating the potential of this technology for ionospheric-related studies. [ABSTRACT FROM AUTHOR]

Gadolinium pyrosilicate (GPS, Gd2Si2O7) single crystals with different doping concentrations of Tb (0.1–2.0 mol%) are successfully fabricated using the floating-zone technique. In this work, the dependence of Tb-doping concentration on the photoluminescence (PL) and scintillation properties of Tb-doped GPS (Tb:GPS) has been investigated. The PL emission contour graph shows multiple emissions, with the strongest emissions at 378 nm for 0.1% and 0.5% Tb-doping and 544 nm for 1.0% and 2.0% Tb-doping, corresponding to Tb3+ 4f-4f transitions. The PL lifetimes of the specimens range from 4.89 to 5.22 ms. The scintillation spectra exhibit comparable wavelength and intensity trends to the PL emission. The scintillation lifetimes of the specimens range from 2.41 to 3.88 ms. The Tb:GPS specimens demonstrate a relatively excessive afterglow level, with Af20 values ranging from 1640 to 7250 ppm and Af40 values ranging from 136 to 362 ppm. Using recently developed pulse height measurement for millisecond decay scintillators, under excitation at 662 keV γ-rays, the 1.0% Tb:GPS specimen exhibits the highest scintillation light yield among all other specimens at 95,600 ph/MeV, making Tb:GPS one of the highest light yield oxide scintillators. [ABSTRACT FROM AUTHOR]

This research investigates the fabrication and analysis of plastic scintillators using an epoxy matrix. Plastic scintillators are widely used in radiation detection because of their low cost, ease of fabrication, resistance to moisture, and rapid decay time. The production process involved dissolving primary and secondary dopants, p-terphenyl (p-TP) and 1,4-bis [2-(phenyloxazolyl)]-benzene (POPOP), respectively, into a low-viscosity of cycloaliphatic amine as hardener B, which was then combined with Bisphenol-A diglycidyl ether as epoxy A. The ratio of primary and secondary dopants was varied in the experiment. The resulting scintillators were characterized using Fourier Transform Infrared Spectroscopy (FTIR) to analyze the functional groups that constitute the epoxy before and after curing. The morphology of the scintillator sample was evaluated using SEM and The thermal properties were evaluated with differential scanning calorimetry (DSC). The optical properties of the scintillator were studied using a UV-Vis Spectrophotometer and a Fluorescence Spectrophotometer. The performance of the scintillator in detecting gamma rays was evaluated using a module comprising a Photomultiplier Tube (PMT) and a Multichannel Analyzer (MCA) with sources of gamma Cesium 137. The results showed that epoxy-based scintillators can provide a detective response to gamma rays. This study demonstrates the potential of epoxy-based plastic scintillators for use in radiation detection. [ABSTRACT FROM AUTHOR]

Introduction: We propose a method for prompt-gamma verification of proton range during particle therapy, called Prompt-Gamma Energy Integration (PGEI). Method: This method is based on the measurement of the total energy deposited in a set of detectors located around a patient. It is particularly suited in the case of high-instantaneous beam intensities, like for pulsed beams extracted from a synchro-cyclotron. GATE simuations were used to evaluate the sensitivity, and dedicated scintillators were tested as a function of beam intensity. Results and discussion: Simulations show that millimetric range shifts can be measured at a beam-spot scale. The sensitivity is slightly degraded as compared to the Prompt-Gamma Peak Integration Method, for which Time-of-Flight can be employed to reduce the background in single-photon detection conditions at cyclotron accelerators. Experimentally, lead tungstate scintillators have shown to cope with the high instantaneous gamma count rates for PGEI at synchrocyclotrons. [ABSTRACT FROM AUTHOR]

The AMoRE-II experiment will search for the 0vßß decay of 100Mo nuclei using molybdate crystal scintillators, operating at milli-Kelvin (mK) temperatures, with a total of 80 kg of 100Mo. The background goal for the experiment is 10-4 counts/keV/kg/year in the region of interest around the 0vßß decay Q-value of 3,034 keV. To achieve this level, the rate of background signals arising from emissions produced by decays of radioactive impurities in the detector and shielding materials must be strictly controlled. To do this, concentrations of such impurities are measured and are controlled through materials selection and purification. In this paper, we describe the design and the construction materials used to build the AMoRE-II detector and shielding system, including active and passive shielding, the cryostat, and the detector holders and instrumentation, and we report on measurements of radioactive impurities within candidate and selected materials., [ABSTRACT FROM AUTHOR]

The interaction between free electrons and optical fields constitutes a unique platform to investigate ultrafast processes in matter and explore fundamental quantum phenomena. Specifically, optically modulated electrons in ultrafast electron microscopy act as noninvasive probes that push space-time-energy resolution to the picometer-attosecond-microelectronvolt range. Electron energies well above the involved photon energies are commonly used, rendering a low electron-light coupling and, thus, only providing limited access to the wealth of quantum nonlinear phenomena underlying the dynamical response of nanostructures. Here, we theoretically investigate electron-light interactions between photons and electrons of comparable energies, revealing quantum and recoil effects that include a nonvanishing coupling of surface-scattered electrons to light plane waves, inelastic electron backscattering from confined optical fields, and strong electron-light coupling under grazing electron diffraction by an illuminated crystal surface. Our exploration of electron-light-matter interactions holds potential for applications in ultrafast electron microscopy. [ABSTRACT FROM AUTHOR]

Thanks to advancements in silicon photomultiplier sensors (SiPMs) and system-on-chip (SoC) technology, our INFN Roma1 group developed ArduSiPM in 2012, the first all-in-one scintillator particle detector in the literature. It used a custom Arduino Due shield to process fast signals, utilizing the Microchip Sam3X8E SoC's internal peripherals to control and acquire SiPM signals. The availability of radiation-tolerant SoCs, combined with the goal of reducing system space and weight, led to the development of an innovative second-generation board, a better-performing device called Cosmo ArduSiPM, suitable for space missions. The architecture of the new detector is based on the Microchip SAMV71 300 MHz, 32-bit ARM® Cortex®-M7 (Microchip Technology Inc., Chandler, AZ, USA). While the analog front-end is essentially identical to the ArduSiPM, it utilizes components with the smallest possible package. The board fits in a CubeSat module. Thanks to the compact design, the board has two independent channels, with a total weight of only 40 grams within a CubeSat form factor. The ArduSiPM architecture is based on a single microcontroller and fast discrete analog electronics. It benefits from the continued development of SoCs related to the IoT (Internet of Things) market. Compared with a system with a custom ASIC, this architecture based on software and SoC capabilities offers considerable advantages in terms of cost and development time. The ability to incorporate new commercial SoCs, continuously emerging from advancements in the aerospace and automotive industries, provides the system with a robust foundation for sustained growth over the years. A detailed characterization of the hardware and the system's response to different photon fluxes is presented in this article. Additionally, coupling the device with a scintillator was tested at the end of this article as a preliminary trial for future measurements, showing potential for further enhancement of the detector's capabilities. [ABSTRACT FROM AUTHOR]

Due to the rapid advancements in medical radiography, nondestructive inspection, and radiation detection, there is an increasing demand for scintillators that offer both cost-effectiveness and high-resolution X-ray imaging. In this study, we have successfully synthesized transparent glass-ceramic scintillator by embedding Tb3+-doped NaLu 2 F 7 nanocrystals in a glass matrix. This scintillator demonstrates excellent spatial resolution of 20 lp/mm in X-ray imaging due to its high transmittance (over 90% at 550 nm) and intense luminescent intensity when excited by X-ray (151% higher than that of the Bi 4 Ge 3 O 12 scintillator). More significantly, the as-synthesized scintillator exhibits exceptional stabilities at high temperature, moisture levels, and moderate radiation exposure. Notably, any decline in performance caused by long-term exposure to high-dose X-ray can be fully recovered through heat treatment at 350 °C for 30 min. These findings highlight the great potential of NaLu 2 F 7 :Tb3+ glass ceramics as suitable options for high-resolution and retrievable X-ray imaging. [ABSTRACT FROM AUTHOR]

The large size (4 cm × 4 cm × 1 cm) Ce3+-doped high gadolinium oxyfluoride glass with density of 5.83 g/cm³ was prepared by the melt quench method at 1220 °C. The glass is colorless and transparent over the visible range. The prolonged decay time under 275 nm UV light demonstrates the energy transfer from Gd3+ ions to Ce3+ ions. The X-ray excited luminescence spectra (XEL) show the emission peak corresponds to the 5d→4f transitions of Ce3+ ion. The integral emission intensity of glass was compared with that of bismuth germanate oxide (BGO) crystals. The scintillation property of glass was studied under the γ -ray from 137Cs source and a clear energy peak was observed with light yield (LY) over 1100 ph/MeV. The scintillation decay time comprises fast and slow components. All results presented in this work indicate the appropriate potential to be high-energy rays detecting material for CEPC. [ABSTRACT FROM AUTHOR]

A series of lead-free Rb2ZrCl6:xTe4+ (x = 0%, 0.1%, 0.5%, 1.0%, 2.0%, 3.0%, 5.0%, 10.0%) perovskite materials were synthesized through a hydrothermal method in this work. The substitution of Te4+ for Zr in Rb2ZrCl6 was investigated to examine the effect of Te4+ doping on the spectral properties of Rb2ZrCl6 and its potential applications. The incorporation of Te4+ induced yellow emission of triplet self-trapped emission (STE). Different luminescence wavelengths were regulated by Te4+ concentration and excitation wavelength, and under a low concentration of Te4+ doping (x ≤ 0.1%), different types of host STE emission and Te4+ triplet state emission could be achieved through various excitation energies. These luminescent properties made it suitable for applications in information encryption. When Te4+ was doped at high concentrations (x ≥ 1%), yellow triplet state emission of Te4+ predominated, resulting in intense yellow emission, which stemmed from strong exciton binding energy and intense electron-phonon coupling. In addition, a Rb2ZrCl6:2%Te4+@RTV scintillating film was fabricated and a spatial resolution of 3.7 lp/mm was achieved, demonstrating the potential applications of Rb2ZrCl6:xTe4+ in nondestructive detection and bioimaging. [ABSTRACT FROM AUTHOR]

Organic scintillators have recently gained considerable attentions in X‐ray detection for their potential applications in biomedical radiograph and security inspection. However, the weak X‐ray absorption and/or inefficient exciton utilization have limited the development and commercialization of organic scintillators. Currently, high‐performance X‐ray organic scintillators are scarce and organic scintillators with dual triplet‐harvesting channels have not been explored before. Here, we develop several proof‐of‐concept sulfone‐based organic molecules, C1–C7, using different alkoxy chains to manipulate molecular packing mode. These materials exhibit dual triplet‐harvesting channels of thermally activated delayed fluorescence (TADF) and room‐temperature phosphorescence (RTP) in aggregated state. Inspiringly, these molecules display distinct radioluminescence under the X‐ray stimulation. Among them, C6 behaves the highest light yield of 16,558 photons MeV−1. Moreover, clear X‐ray images are demonstrated in both aggregated state and single‐molecule level. High spatial resolutions of 15.0 and 10.6 line pairs per millimeter (lp mm−1) are achieved for rigid and flexible scintillator screens, exceeding most reported organic and conventional inorganic scintillators. These results highlight the great potential of organic molecules with TADF and RTP nature for efficient X‐ray scintillation and imaging. [ABSTRACT FROM AUTHOR]

In this study, we introduce the concept and construction of an innovative Digital Miniature Cathode Ray Magnetometer designed for the precise detection of magnetic fields. This device addresses several limitations inherent to magnetic probes such as D.C. offset, nonlinearity, temperature drift, sensor aging, and the need for frequent recalibration, while capable of operating in a wide range of magnetic fields. The core principle of this device involves the utilization of a charged particle beam as the sensitivity medium. The system leverages the interaction of an electron beam with a scintillator material, which then emits visible light that is captured by an imager. The emitted scintillation light is captured by a CMOS sensor. This sensor not only records the scintillation light but also accurately determines the position of the electron beam, providing invaluable spatial information crucial for magnetic field mapping. The key innovation lies in the combination of electron beam projection, CMOS imager scintillation-based detection, and digital image signal processing. By employing this synergy, the magnetometer achieves remarkable accuracy, sensitivity and dynamic range. The precise position registration enabled by the CMOS sensor further enhances the device's utility in capturing complex magnetic field patterns, allowing for 2D field mapping. In this work, the optimization of the probe's performance is tailored for applications related to the characterization of insertion devices in light sources, including undulators. [ABSTRACT FROM AUTHOR]

Atmospheric turbulence causes transmitted light to fade randomly, which results in irradiance scintillation fluctuations in the received signal and significantly affects the quality of wireless optical communication systems. In this paper, we investigate the propagation characteristics of a monochromatic light-emitting diode (LED) light beam through weak-to-strong turbulence. Considering the spatial incoherence of a monochromatic LED light source, the emitted light field of a monochromatic LED light source is represented by a random field multiplied by a deterministic field that follows a Gaussian distribution. Then, based on the extended-Rytov theory, a closed expression for the irradiance scintillation index under weak-to-strong turbulence is derived. In addition, the expression for the fading probability governed by the Gamma–Gamma model is given. Finally, the effects of near-earth atmospheric refractive index structural parameters, signal propagation distances, and working light wavelengths on propagation characteristics of the LED-based VLC system are simulated and compared with those of the laser-based one. The results theoretically confirm that laser light sources are more susceptible to atmospheric turbulence along the propagation path than monochromatic LED light sources. The investigation in this paper can provide theoretical support for the design of visible light communication systems in practical applications. [ABSTRACT FROM AUTHOR]

Liquid scintillator detectors have great advantages in the field of radionuclide detection because of their low detection limit, high sensitivity, and diverse functions. However, the material properties of liquid scintillators directly determine their detection effectiveness, which leads to their poor vertex resolution and particle identification. In this work, we introduce the improvement methods, choices, and properties of different novel liquid scintillator materials in recent years. This article is expected to provide references for the development and research of liquid scintillator materials in various application fields. [ABSTRACT FROM AUTHOR]

The synthesis and characterization of cerium-doped lanthanum fluoride (La(1−x)CexF3) nanocrystals have been carried out. The surfaces of La(1−x)CexF3 nanocrystals were modified with oleic acid using the co-precipitation technique, and then doped with cerium with various mole fractions (x) = 0.05, 0.10, 0.15, 0.20, and 0.25. The nanocrystals produced were characterized for their crystal structure using x-ray diffraction (XRD), their morphology by transmission electron microscopy (TEM), their functional group identification using Fourier-transform infrared (FTIR), and Raman spectroscopy, and their photoluminescence behavior using photoluminescence (PL) spectroscopy. Detailed investigations revealed that, based on the XRD data and TEM images, La(1−x)CexF3 exhibits trigonal-structured nanocrystals with the symmetry space group P-3c1. Among the samples, La0.75Ce0.25F3 exhibited the sharpest PL peak. The PL spectra for La0.75Ce0.25F3 nanocrystals excited at 370 nm and showed an intense emission peak at 495 nm with a lifetime τ = 1.523 × 10−10 s. This emission was assigned to the 5d → 4f (2F5/2 and 2F7/2) transitions of Ce3+ energy levels, indicating a luminescence center mechanism. These results indicate that the synthesized La0.75Ce0.25F3 is a promising phosphor material for detector scintillators. [ABSTRACT FROM AUTHOR]

Introduction: Radiation dose measurement is an essential part of radiotherapy to verify the correct delivery of doses to patients and ensure patient safety. Recent advancements in radiotherapy technology have highlighted the need for fast and precise dosimeters. Technologies like FLASH radiotherapy and magnetic‐resonance linear accelerators (MR‐LINAC) demand dosimeters that can meet their unique requirements. One promising solution is the plastic scintillator‐based dosimeter with high spatial resolution and real‐time dose output. This study explores the feasibility of using the LuSy dosimeter, an in‐house developed plastic scintillator dosimeter for dose verification across various radiotherapy techniques, including conformal radiotherapy (CRT), intensity‐modulated radiation therapy (IMRT), volumetric‐modulated arc therapy (VMAT), and stereotactic radiosurgery (SRS). Materials and methods: A new dosimetry system, comprising a new plastic scintillator as the sensing material, was developed and characterized for radiotherapy beams. Treatment plans were created for conformal radiotherapy, IMRT, VMAT, and SRS and delivered to a phantom. LuSy dosimeter was used to measure the delivered dose for each plan on the surface of the phantom and inside the target volumes. Then, LuSy measurements were compared against an ionization chamber, MOSFET dosimeter, radiochromic films, and dose calculated using the treatment planning system (TPS). Results: For CRT, surface dose measurement by LuSy dosimeter showed a deviation of ‐5.5% and ‐5.4% for breast and abdomen treatment from the TPS, respectively. When measuring inside the target volume for IMRT, VMAT, and SRS, the LuSy dosimeter produced a mean deviation of ‐3.0% from the TPS. Surface dose measurement resulted in higher TPS discrepancies where the deviations for IMRT, VMAT, and SRS were ‐2.0%, ‐19.5%, and 16.1%, respectively. Conclusion: The LuSy dosimeter was feasible for measuring radiotherapy doses for various treatment techniques. Treatment delivery verification enables early error detection, allowing for safe treatment delivery for radiotherapy patients. [ABSTRACT FROM AUTHOR]

The thickness of the scintillation films in indirect X−ray detectors can significantly influence their luminescence intensity. However, due to the scattering and attenuation of incoherent photons, thick scintillation films tend to reduce light yield. Herein, a highly transparent perovskite glass−ceramic scintillation film, in which the CsPbBr3 nanocrystals are in-situ grown inside a transparent amorphous polymer structure, is designed to achieve ultrastable and efficient X-ray imaging. The crystal coordination−topology growth and in−situ film formation strategy is proposed to control the crystal growth and film thickness, which can prevent light scattering and non−uniform distribution of CsPbBr3 nanocrystals while providing sufficient film thickness to absorb X−ray, thus enabling a high−quality glass−ceramic scintillator without agglomeration and Ostwald ripening. This glass−ceramic scintillation film with a thickness of 250 μm achieves a low detection limit of 326 nGyair s−1 and a high spatial resolution of 13.9 lp mm−1. More importantly, it displays remarkable scintillation stability under X−ray irradiation (radiation intensity can still reach 95% at 278 μGyair s−1 for 3600 s), water soaking (150 days), and high−temperature storage (150 days at 60 °C). Hence, this work presents a approach to construct ultrastable and flexible scintillation films for X−ray imaging with reduced light scattering and improved resolution. [ABSTRACT FROM AUTHOR]

In this paper, we present the new multi-wavelength dataset of aerosol extinction profiles, which are retrieved from the averaged transmittance spectra by the Global Ozone Monitoring by Occultation of Stars instrument aboard the Envisat satellite. Using monthly and zonally averaged transmittances as a starting point for the retrievals enables us to improve the signal-to-noise ratio and eliminate possible modulation of transmittance spectra by uncorrected scintillations. The two-step retrieval method is used: the spectral inversion is followed by the vertical inversion. The spectral inversion relies on the removal of contributions from ozone, NO2 , NO3 and Rayleigh scattering from the optical depth spectra for each ray perigee altitude. In the vertical inversion, the profiles of aerosol extinction coefficients at several wavelengths are retrieved from the collection of slant aerosol optical depth profiles. The retrieved aerosol extinction profiles (FMI-GOMOSaero dataset v1) are provided in the altitude range 10–40 km at wavelengths of 400, 440, 452, 470, 500, 525, 550, 672 and 750 nm for the whole GOMOS operating period from August 2002 to March 2012. Extensive intercomparisons of the retrieved FMI-GOMOSaero aerosol profiles with aerosol profile data from other satellite instruments at several wavelengths have been performed. It is found that the average difference between FMI-GOMOSaero and other datasets is within 20 %–40 % in the lower and middle stratosphere, the standard deviation is ∼ 20 %–50 %, and the correlation coefficient of the time series is 0.65–0.85. The created FMI-GOMOSaero dataset can be used in merged datasets of stratospheric aerosols. It might be also used as a priori information for satellite retrievals during 2002–2012. [ABSTRACT FROM AUTHOR]

Upconversion nanoparticles (UCNPs), particularly those that are highly doped, possess outstanding properties and have demonstrated tremendous application potential. However, novel fine-tuning strategies are urgently required to enhance the upconversion luminescence (UCL) performance of UCNPs. In this study, a series of core–multishell UCNPs highly doped with Ho3+ and Yb3+ ions were synthesized via the oleate route. The X-ray diffraction (XRD), transmission electron microscopy (TEM), and UCL spectra and decay times, and pump power dependency of the synthesized UCNPs were used to examine their morphology, size, and the UCL properties. Ce3+ ions were introduced to enhance Ho3+-based red UCL, and their doping strategy was also optimized based on summarized UCL trends and detailed UCL mechanism analysis. NaHoF 4 :Gd3+@NaGdF 4 :Yb3+,Ce3+@NaGdF 4 :Yb3+ UCNPs that had 10 mol% Ce3+ dopants in their middle shells exhibited better UCL properties than the larger traditional NaGdF 4 :Yb3+,Ce3+,Ho3+ UCNPs, probably because of the combined influence of the energy interactions between the Ce3+ ions and surface groups, sensitizing energy enhancement by active shells, and the positive cooperation between the Ce3+ ions and highly-doped core–shell structures. In this study, the phenomenon of UCL decrease resulting from Ce3+ ion doping was explored. Using unique core–multishell structures with highly-doped activators and sensitizers placed within and outside the structures, respectively, the UCL decrease due to Ce3+ ion doping was attributed to a competition for photons. Doping the UCNPs with Ce3+ ions near the UCNP surfaces favors Ho3+-based red UCL. Our study findings can deepen the understanding of the Ho3+-based UCL mechanisms and increase the potential uses of NaHoF 4 materials in photo-induced therapy. When Ce3+ ions are doped near the nanoparticle surface, they might have energy interactions with surface groups to relieve phonon energy shortage and thus enhance the efficiency of cross-relaxation between Ho3+ and Ce3+ ions. [Display omitted] [ABSTRACT FROM AUTHOR]

The phosphor-converted white light-emitting diodes (pc- w LEDs) are current research hotspot. To meet simultaneously the requirements of high chemical/thermal stability and color-rendering index (CRI), low correlated color temperature (CCT) for actual application is still not be perfectly achieved. Herein, we studied for the first time the incorporation of Ce3+ (blue-emitting) and Mn2+ (orange/red emission) into the dibarium magnesium phosphate ceramic (Ba 2 Mg(PO 4) 2 , BMP) for packaging of pc- w LEDs via remote 'capping' approach, which exhibits highly efficient color-tunable photoluminescence (PL) with splendid chemical/thermal stability, single-phase/full-color-PL, efficient energy transfer (ET). To reduce the impact of heterovalent substitution (Ba2+ ← Ce3+), the monovalent (Li+, Na+, K+) ion, respectively tridoped in BMP: Ce/Mn and played both roles as flux and charge compensator, were also studied/compared on the basis of PL efficiency, where Na+ is the most effective because of the lowest electronegativity mismatch between the Ba2+ and Na+. An alkaline-earth-metal-ion blending strategy via partial replacement of Ba2+ with Sr2+ was implemented to further regulate PL and obtain better parameters of CCT/CRI due to the variations of crystal field splitting. The site occupations of Ce/Na/Sr in Ba sites (CN = 8 and 7) and Mn in Mg site (CN = 6) were based on the comparisons of ion radius and confirmed by XRD/Rietveld analyses, where Ce/Na/Sr ions gave priority to occupy the Ba site with CN = 8 due to their much closer ion radius. Altogether, the stably composition-optimized BMP: Ce/Mn/Na/Sr has great potential application as a single-component color-tunable phosphor in n -UV pumped pc- w LEDs. The pc- w LED fabricated via remote 'capping' approach by combination of a n -UV chip with BMP: Ce/Mn/Na/Sr phosphor through Ce to Mn ET with the help of charge compensator of Na and the alkaline-earth-metal-ions blending by Ba/Sr replacement. [Display omitted] • Ce/Sr/Na occupied at Ba sites while Mn sited in Mg sites. • ET occurs efficiently from Ce to Mn. • Na + acts as charge balancer to improve PL efficiency. • Replacing partial Ba by Sr could regulate PL and improve ET efficiency. • pc- w LED via ' n -UV LED + white-emitting BMP: Ce/Mn/Na/Sr' is achieved. [ABSTRACT FROM AUTHOR]

Open Hardware-based microcontrollers, especially the Arduino platform, have become a comparably easy-to-use tool for rapid prototyping and implementing creative solutions. Such devices in combination with dedicated front-end electronics can offer low-cost alternatives for student projects, slow control and independently operating small-scale instrumentation. The capabilities can be extended to data taking and signal analysis at mid-level rates. Two detector realizations are presented, which cover the readouts of proportional counter tubes and of scintillators or wavelength-shifting fibers with silicon photomultipliers (SiPMs). The SiPMTrigger realizes a small-scale design for coincidence readout of SiPMs as a trigger or veto detector. It consists of a custom mixed signal front-end board featuring signal amplification, discrimination and a coincidence unit for rates of up to 200 kHz. The nCatcher transforms an Arduino Nano to a proportional counter readout with pulse shape analysis: time over threshold measurement and a 10-bit analog-to-digital converter for pulse heights. The device is suitable for low-to-medium-rate environments up to 5 kHz, where a good signal-to-noise ratio is crucial. We showcase the monitoring of thermal neutrons. For data taking and slow control, a logger board is presented that features an SD card and GSM/LoRa interface. [ABSTRACT FROM AUTHOR]

• CeBr 3 and NaI (Tl) scintillators characterized with array of Silicon Photomultipliers. • Energy resolution improves with lower shaping time and higher SiPM over-voltage. • Temperature dependency of gain of SiPM array: ∼−0.81 %/°C for overvoltage of 2.5 Volts. • Temperature dependency of light yield for CeBr 3 : ∼−0.27 %/°C for −31 °C to +26 °C. • Temperature dependency of light yield for NaI (Tl): ∼+0.5 %/°C for −31 °C to +26 °C. Interaction of X-rays with a scintillation detector produces optical photons in the visible range. The spectral and spatial information of the X-ray can be derived by detecting these output photons using a Silicon Photomultiplier (SiPM). Two types of detector modules: CeBr 3 and NaI (Tl), coupled with an array of SiPM are presented here, which are being developed for the future space exploration programs. The development of the front end electronics (FEE) for the charge readout from SiPM for X-ray spectrometer application is presented here which is characterized for SiPM's over-voltages and shaping amplifier's time constant. In this article, both the detector modules are subjected to a wide temperature range to establish a relationship of the SiPM's gain, energy resolution and scintillators' output photon yield with ambient temperature. The test results show that energy resolution improves with higher over-voltage of SiPM and also with lower operating temperature. The gain of the SiPM array shows negative temperature dependence of ∼−0.81 %/°C for an over-voltage of 2.5 Volts. To derive the temperature dependency of scintillators' output photons, gain of the SiPM array was made constant by operating it at a fixed over-voltage for a wide temperature range. With the constant gain of SiPM, CeBr 3 scintillator shows negative temperature coefficient of ∼−0.27 %/°C and NaI (Tl) shows positive temperature coefficient of ∼+0.5 %/°C for the light output in the temperature range of −31 °C to +26 °C. [ABSTRACT FROM AUTHOR]

We measure the decay time and the attenuation length of newly developed wavelength-shifting fibers, the YS series, from Kuraray, which have a fast response. Using a 405 nm laser, the decay times of YS-2, 4, and 6 are measured to be 3.64 ± 0.04, 2.15 ± 0.03, and 1.47 ± 0.02 ns, respectively, for a light injection distance of 10 cm. The decay time of Y-11 is measured to be 7.10 ± 0.09 ns using the same system. All fibers are found to have similar attenuation lengths of more than 4 m. When combined with the plastic scintillators EJ-200 and EJ-204, the YS series has better time resolution than Y-11, with light yields of 60–100% of Y-11. [ABSTRACT FROM AUTHOR]

Following the discovery of X-rays, scintillators are commonly used as high-energy radiation sensors in diagnostic medical imaging, high-energy physics, astrophysics, environmental radiation monitoring, and security inspections. Conventional scintillators face intrinsic limitations including a low extraction efficiency of scintillated light and a low emission rate, leading to efficiencies that are less than 10 % for commercial scintillators. Overcoming these limitations will require new materials including scintillating nanomaterials ("nanoscintillators"), as well as new photonic approaches that increase the efficiency of the scintillation process, increase the emission rate of materials, and control the directivity of the scintillated light. In this perspective, we describe emerging nanoscintillating materials and three nanophotonic platforms: (i) plasmonic nanoresonators, (ii) photonic crystals, and (iii) high-Q metasurfaces that could enable high performance scintillators. We further discuss how a combination of nanoscintillators and photonic structures can yield a "super scintillator" enabling ultimate spatio-temporal resolution while enabling a significant boost in the extracted scintillation emission. [ABSTRACT FROM AUTHOR]

Inorganic scintillation crystals have been widely used in applications of high-energy physics, nuclear medical imaging, industrial nondestructive inspection, etc. In this work, a single crystal Ba3Y(PO4)3 (BYP) with 1.0 at% Ce3+-doping concentration was first grown by the Czochralski method, and the electronic structure was calculated using first principles based on density functional theory. In addition, a series of Ce3+-doped BYP phosphors were synthesized, and the fluorescence emission under UV excitation was measured through low-temperature spectroscopy, containing double-peaked emission from 5d–4f transition and self-trapped exciton recombination. A comparison of the UV and X-ray-excited fluorescence spectra reveals the existence of oxygen vacancies as well as F+ centers in the crystal. The air annealing of the crystal effectively reduces the thermoluminescence defects but reduces the emission intensity under UV or X-ray excitation. The BYP:Ce crystal shows a fast decay lifetime of 15.5 ns, and the fast component is as short as 8 ns. The results show that the Ce3+-doped BYP crystal has potential as a kind of scintillator with fast decay properties. [ABSTRACT FROM AUTHOR]

Cone-beam computed tomography (CBCT) has emerged in recent years as an adequate alternative to mammography and tomosynthesis due to the several advantages over traditional mammography, including its ability to provide 3D images, its reduced radiation dose, and its ability to image dense breasts more effectively and conduct more effective breast compressions, etc. Furthermore, CBCT is capable of providing images with high sensitivity and specificity, allowing a more accurate evaluation, even of dense breasts, where mammography and tomosynthesis may lead to a false diagnosis. Clinical and experimental CBCT systems rely on cesium iodine (CsI:Tl) scintillators for X-ray energy conversion. This study comprises an investigation among different novel CBCT detector technologies, consisting either of scintillators (BGO, LSO:Ce, LYSO:Ce, LuAG:Ce, CaF2:Eu, LaBr3:Ce) or semiconductors (Silicon, CZT) in order to define the optimum detector design for a future experimental setup, dedicated to breast imaging. For this purpose, a micro-CBCT system was adapted, using GATE v9.2.1, consisting of the aforementioned various detection schemes. Two phantom configurations were selected: (a) an aluminum capillary positioned at the center of the field of view in order to calculate the system's spatial resolution and (b) a breast phantom consisting of spheres of different materials, such that their characteristics are close to the breast composition. Breast phantom contrast-to-noise ratios (CNRs) were extracted from the phantom's tomographic images. The images were reconstructed with filtered back projection (FBP) and ordered subsets expectation-maximization (OSEM) algorithms. The semiconductors acted satisfactorily in low-density matter, while LYSO:Ce, LaBr3:Ce, and LuAG:Ce presented adequate CNRs for all the different spheres' densities. The energy converters that are presented in this study were evaluated for their performance against the standard CsI:Tl crystal. [ABSTRACT FROM AUTHOR]