Search

Different types of resonators are used to create acoustic metamaterials and metasurfaces. Recent studies focused on the use of multiple resonators of the dipole, quadrupole, octupole, and even hexadecapole types. This paper considers the theory of an acoustic metasurface, which is a flat surface with a periodic arrangement of multipole resonators. The sound field reflected by the metasurface is determined. If the distance between the resonators is less than half the wavelength of the incident plane wave, the far field can be described by a reflection coefficient that depends on the angle of incidence. This allows us to characterize the acoustic properties of the metasurface by a homogenized boundary condition, which is a high-order tangential impedance boundary condition. The tangential impedance depending on the multipole order of the resonators is introduced. In addition, we analyze the sound absorption properties of these metasurfaces, which are a critical factor in determining their performance. The paper presents a theoretical model for the subwavelength case that accounts for the multipole orders of resonators and their impact on sound absorption. The maximum absorption coefficient for a diffuse sound field, as well as the optimal value for the homogenized impedance, are calculated for arbitrary multipole orders. The examples of the multipole resonators, which can be made from a set of Helmholtz resonators or membrane resonators, are discussed as well.

Measuring the optical properties of highly diffuse materials is a challenge as it could be related to the white colour or an oversaturation of pixels in the acquisition system. We used a spatially resolved method and adapted a nonlinear trust-region algorithm to the fit Farrell diffusion theory model. We established an inversion method to estimate two optical properties of a material through a single reflectance measurement: the absorption and the reduced scattering coefficient. We demonstrate the validity of our method by comparing results obtained on milk samples, with a good fitting and a retrieval of linear correlations with the fat content, given by R2 scores over 0.94 with low p-values. The values of absorption coefficients retrieved vary between 1 × 10−3 and 8 × 10−3 mm−1, whilst the values of the scattering coefficients obtained from our method are between 3 and 8 mm−1 depending on the percentage of fat in the milk sample, and under the assumption of the anisotropy factor g>0.8. We also measured and analyzed the results on white paint and paper, although the paper results were difficult to relate to indicators. Thus, the method designed works for highly diffuse isotropic materials.

Next generation in-to-out-of body biomedical applications have adopted optical wireless communications (OWCs). However, by delving into the published literature, a gap is recognized in modeling the in-to-out-of channel, since most published contributions neglect the particularities of different types of tissues. In this paper, we present a novel pathloss and scattering models for in-to-out-of OWC links. Specifically, we derive extract analytical expressions that accurately describe the absorption of the five main tissues’ constituents, namely fat, water, melanin, and oxygenated and de-oxygenated blood. Moreover, we formulate a model for the calculation of the absorption coefficient of any generic biological tissue. Next, by incorporating the impact of scattering in the aforementioned model, we formulate the complete pathloss model. The developed model is verified by means of comparisons between the estimated pathloss and experimental measurements from independent research works. Finally, we illustrate the accuracy of the proposed model in estimating the optical properties of any generic tissue based on its constitution. The extracted channel model is expected to enable link budget analysis, performance analysis, and theoretical framework development, which will boost the design of optimized communication protocols for a plethora of biomedical applications.

The paper focuses on the area of experimental measurements for monitoring the impact of decarbonization on the technical and environmental parameters of the ICE. The condition for the implementation of the measurements was the selection of an ICE that had driven more than 300,790 km. During the laboratory tests, several test methods were used to assess the technical and emission conditions of the tested ICE with the code designation ALH, which is used in VOLKSWAGEN BORA vehicles. The technical parameters of the tested ICE (corrected power PNorm and torque MMom), emission parameters (absorption coefficient k and NOx emission) and fuel consumption parameters (specific fuel consumption bsfc) were compared and evaluated in the results. The results show that the decarbonization process on the tested vehicle VOLKSVWAGEN BORA 1.9 TDi affected the emission parameters but did not affect the technical parameters and specific fuel consumption.

Terahertz (THz) frequency generation via nonlinear optical techniques is of particular interest due to the immense potential of this type of radiation in various scientific fields, ranging from medicine to telecommunications. Selecting suitable nonlinear media for laser frequency down-conversion presents a challenging task. Considering an approach that uses nonlinear crystals with high radiation resistance, pumped by intense laser pulses near their damage threshold, we suggest the crystal of bismuth triborate (BiB3O6, BIBO). Compared to other borate-class crystals, BIBO exhibits relatively high coefficients of quadratic susceptibility. In this paper, we have studied the optical properties of BIBO samples in a wide spectral range from 0.1 to 2.1 THz at temperatures of 473, 383, 295, and 77 K using Terahertz Time-Domain Spectroscopy (THz-TDS). Furthermore, we simulated collinear three-wave interactions with nonzero efficiency for difference frequency generation (DFG) in the THz range. For the pump wavelengths of about 800 nm, we determined phase-matching (PM) conditions and compared the generation efficiency for different crystal cuts. The potential of utilizing BIBO crystal for terahertz frequency generation is discussed.

In recent years, the possibility of combining graphene and carbon nanotubes has attracted much attention from researchers attempting to obtain new multifunctional hybrid materials with promising properties. Optoelectronics shows potential as a field of application for such hybrid structures. The variety of existing structural configurations of graphene-nanotube hybrids requires preliminary detailed studies of their optical properties by computer simulation methods. In this paper, we consider island-type graphene-nanotube hybrid films formed by AB-stacked bilayer graphene and single-walled carbon nanotubes (SWCNTs). In this case, bilayer graphene is located above the surface of the nanotube, forming areas with an increased density of carbon atoms, creating so-called “islands.” To meet the conditions of a real experiment, we chose chiral SWCNTs (12,6) with a diameter of 1.2 nm, which are most often synthesized in real experiments. All constructed atomistic models of bilayer graphene-chiral SWCNT films were tested for thermodynamic stability at room temperature and proved their suitability for research. Using Kubo-Greenwood formalism, we calculated the complex optical conductivity tensor and absorbance coefficient in the wavelengths of ultraviolet, visible, and near-infrared radiations. The photocurrent spectra are calculated based on the obtained absorption spectra and solar radiation spectra on the earth’s surface (AM1.5) and outside the earth’s atmosphere (AM0). The results of calculations revealed regularities in the influence of structural parameters (nanotube diameter, graphene width) on the optical and optoelectronic properties of graphene-chiral SWCNT (12,6) with an island structure.

The paper presents the sound absorption coefficient of acoustic absorbers fabricated from natural durian husk fibers, which are currently still considered as agricultural wastes, especially in Malaysia. Samples were fabricated with different fiber densities and thicknesses and the sound absorption performance was measured using the impedance tube method. The results reveal that the durian husk fibers can have absorption coefficient of more than 0.5 above 1 kHz for a minimum thick sample of 20 mm and with minimum density of 160 kg/m3. The optimised macroscopic parameters for various densities were calculated using the inverse method employing the well-known Johnson-Champoux-Allard (JCA) model for porous material.

This paper is concerned with the nonexistence of global solutions to fractional in time nonlinear Schrödinger equations of the form i α ∂ t α ω ( t , z ) + a 1 ( t ) Δ ω ( t , z ) + i α a 2 ( t ) ω ( t , z ) = ξ | ω ( t , z ) | p , ( t , z ) ∈ ( 0 , ∞ ) × R N , where N ≥ 1 , ξ ∈ C \ { 0 } and p > 1 , under suitable initial data. To establish our nonexistence theorem, we adopt the Pohozaev nonlinear capacity method, and consider the combined effects of absorption and dispersion terms. Further, we discuss in details some special cases of coefficient functions a 1 , a 2 ∈ L l o c 1 ( [ 0 , ∞ ) , R ) , and provide two illustrative examples.

This paper reports an InAs/InAsSb strained-layer superlattice (SLS) mid-wavelength infrared detector and a focal plane array particularly suited for high-temperature operation. Utilizing the nBn architecture, the detector structure was grown by molecular beam epitaxy and consists of a 5.5 µm thick n-type SLS as the infrared-absorbing element. Through detailed characterization, it was found that the detector exhibits a cut-off wavelength of 5.5 um, a peak external quantum efficiency (without anti-reflection coating) of 56%, and a dark current of 3.4 × 10-4 A/cm2, which is a factor of 9 times Rule 07, at 160 K temperature. It was also found that the quantum efficiency increases with temperature and reaches ~56% at 140 K, which is probably due to the diffusion length being shorter than the absorber thickness at temperatures below 140 K. A 320 × 256 focal plane array was also fabricated and tested, revealing noise equivalent temperature difference of ~10 mK at 80 K with f/2.3 optics and 3 ms integration time. The overall performance indicates that these SLS detectors have the potential to reach the performance comparable to InSb detectors at temperatures higher than 80 K, enabling high-temperature operation.

This paper addresses the challenging task of optical characterization of pure, dielectric (nano-)powders with the aim to provide an end-to-end instruction from appropriate sample preparation up to the determination of material remission and absorption spectra. We succeeded in establishing an innovative preparation procedure to reproducibly obtain powder pellet samples with an ideal Lambertian scattering behavior. As a result, a procedure based on diffuse reflectance spectroscopy was developed that allows for (i) performing reproducible and artifact-free, high-quality measurements as well as (ii) a thorough optical analysis using Monte Carlo and Mie scattering simulations yielding the absorption spectrum in the visible spectral range. The procedure is valid for the particular case of powders that can be compressed into thick, non-translucent pellets and neither requires embedding of the dielectric (nano-)powders within an appropriate host matrix for measurements nor the use of integrating spheres. The reduced spectroscopic procedure minimizes the large number of sources for errors, enables an in-depth understanding of non-avoidable artifacts and is of particular advantage in the field of material sciences, i.e., for getting first insights to the optical features of a newly synthesized, pure dielectric powder, but also as an inline inspection tool for massively parallelised material characterization.

In this paper, a model to estimate minibands and theinterminiband absorption coefficient for a wurtzite (WZ) indium gallium nitride (InGaN) self-assembled quantum dot superlattice (QDSL) is developed. It considers a simplified cuboid shape for quantum dots (QDs). The semi-analytical investigation starts from evaluation through the three-dimensional (3D) finite element method (FEM) simulations of crystal mechanical deformation derived from heterostructure lattice mismatch under spontaneous and piezoelectric polarization effects. From these results, mean values in QDs and barrier regions of charge carriers’ electric potentials and effective masses for the conduction band (CB) and three valence sub-bands for each direction are evaluated. For the minibands’ investigation, the single-particle time-independent Schrödinger equation in effective mass approximation is decoupled in three directions and resolved using the one-dimensional (1D) Kronig–Penney model. The built-in electric field is also considered along the polar axis direction, obtaining Wannier–Stark ladders. Then, theinterminiband absorption coefficient in thermal equilibrium for transverse electric (TE) and magnetic (TM) incident light polarization is calculated using Fermi’s golden rule implementation based on a numerical integration into the first Brillouin zone. For more detailed results, an absorption coefficient component related to superlattice free excitons is also introduced. Finally, some simulation results, observations and comments are given.