Search

The sealing capacities of shale, roof, and floor strata are essential for the preservation of shale gas. Sealing capacity development and its influence on shale gas composition and organic matter pore development are important but have not been addressed by existing studies. In this paper, the Upper Ordovician Wufeng-the first member of the Lower Silurian Longmaxi Fm. in the Yangtze region is selected as the study object. We dissected the J1 well in the Jiaoshiba block inside the Sichuan Basin and the Y6 well in the Youyang block outside the Sichuan Basin to analyze the gas components and carbon isotopes in recovered shale gas. In this study, two microscope techniques (i.e., FIB-SEM and FIB-HIM), porosity measurement, TOC content analysis, permeability tests, isothermal adsorption measurements, are utilized. The analytical results show that both the roof and floor strata have vertical sealing effects on the organic-rich shale due to their different physical properties compared to the shale. The shale overburden pressure increases with burial depth, and the adsorbed gas increases with increasing TOC content and thickness: all of these can lead to a decrease in permeability and an increase in self-sealing capacity. This paper determined the formation mechanism of the sealing capacity for shale, roof and floor strata. Furthermore, the control patterns of "sealing capacity strength" on the shale gas source and organic matter pore development are clarified. The main findings are as follows: when the shale, roof, and floor strata have a strong sealing capacity, only a small amount of liquid hydrocarbons can be discharged from the shale, but the natural gas formed due to liquid hydrocarbon cracking is abundant. Under such circumstances, shale gas has a mixed origin of liquid hydrocarbon cracked gas and kerogen cracked gas; the carbon isotopes are inverted; abundant pyrobitumen pores with high porosity and good connectivity are developed. When the sealing capacities are weak, the amount of liquid hydrocarbons discharged from the shale are high, and the amount of natural gas is low. The shale gas is mainly derived from kerogen cracking with weak or no carbon isotope inversion, and kerogen pores are small with poor connectivity. These findings will advance the study of shale gas formation mechanisms and provide a scientific basis for selecting shale gas exploration area. • Due to different physical properties, the roof and floor strata provide a seal for the organic-rich shale. • As the burial depth, TOC content, and the shale thickness increase, the shale has a stronger sealing capacity. • Sealing capacity plays an important role in the characteristics of shale gas and organic matter pore development. [ABSTRACT FROM AUTHOR]

• CH 4 and (sub and supercritical) CO 2 adsorption experiments on shales were performed. • The adsorption ratio of CO 2 over CH 4 for tested shale samples ranges from 1.66–8.32. • Langmuir, D-A, D-R and Ono-Kondo models were fitted to the adsorption data. • The favorable models used to fit CH 4 and CO 2 adsorption on shales are recommended. A thorough study of the adsorption behavior of shales to methane (CH 4) and carbon dioxide (CO 2) is critical for carbon dioxide sequestration in shale gas reservoirs and enhanced shale gas recovery. This paper discusses the results of an adsorption study of CH 4 and CO 2 , in single gas environment, on a set of shale samples taken from the Sichuan and Ordos Basins. The results indicated that shale exhibit higher affinity to CO 2 as compared to CH 4 under similar pressure and temperature conditions, and the preferential adsorption ratio of CO 2 over CH 4 varies between 1.66 and 8.32. Furthermore, the experimental data were modeled using Langmuir, Dubibin-Astakhov (D-A), Dubinin-Redushckevich (D-R) and Ono-Kondo models. The accuracy of the models in quantifying CH 4 and CO 2 adsorption on shale was compared using an error analysis technique. For CH 4 , both of Langmuir and D-A models performed satisfactorily with comparable accuracy. For subcritical CO 2 , the performance of the D-A model is the best. However, for supercritical CO 2 , Ono-Kondo model fitted the experimental data the best, which is the proposed model to use. The results of this study can provide the basis for the estimation of the CO 2 sequestration capacity in shale formations. [ABSTRACT FROM AUTHOR]

Abstract Multiphase (adsorbed and free) liquid water that is accumulated in shale matrix pores (i.e., pore water) substantially affects the storage and transport of gas in shale. Traditionally used macroscopic parameters (e.g., initial, irreducible, mobile and clay bound water saturations) are not sufficient to describe the microdistribution characteristics and mobility of pore water in the complex porous shale matrix. In this paper, a new classification was proposed in which the pore water is composed of adsorbed and free parts, of which the latter is subdivided into capillary bound and mobile water. The components of pore water have the following features: during the centrifugation process, (a) adsorbed water is essentially immobile, while free water is potentially mobile; (b) capillary bound water is gradually transformed into mobile water with increased centrifugal pressure difference; and (c) the maximum mobile water amount is numerically equal to the free water amount. Based on the classification, an effective technique, which integrates centrifugation, water imbibition and low temperature nitrogen adsorption methods with the modified Li's adsorption ratio equation (2018), was established to quantitatively evaluate the microdistribution characteristics (adsorbed and free amounts and their ratios) and the mobility (mobile amount, potential and capacity) of pore water in marine shales from the southern Sichuan basin in China. Furthermore, the mechanism of controlling the microdistribution and mobility of pore water is analyzed with respect to the microscopic pore structure characteristics and material compositions of shales. The primary results demonstrate that (1) adsorbed and free water amounts obtained by centrifugation tests range from 5.145 to 31.282 mg/g (adsorbed) and from 7.880 to 49.751 mg/g (free); the weight ratio of adsorbed water is 0.268–0.629. (2) The mobile potential and mobile capacity of pore water are represented by the free water amount and mid-value pressure difference, respectively. A positive relationship between these two parameters occurs in the studied shales. (3) Pore microstructure characteristics of shale mainly impact the microdistribution and mobility of pore water in the shale matrix. The adsorbed water amount is closely associated with the specific surface area of pores, while the free and mobile water amounts are controlled by the pore volume. The ratios of adsorbed and free water depend on the size and morphology of pores for certain state parameters. The mobile ratio is impacted by pore complexity, which indicates that as the complexity increases, the mobile ratio decreases. The study provides significant insight into the microdistribution and mobility of pore water in gas shale matrix. Highlights • A new classification was proposed for the components of pore water. • A technique was established to evaluate the microdistribution characteristics and the mobility of pore water in shales. • Mechanism of controlling the microdistribution and mobility of pore water was analyzed. [ABSTRACT FROM AUTHOR]

In the process of hydraulic fracturing of shale gas horizontal wells in the Weiyuan area of Sichuan, China, casing deformation (CD) is a frequent problem that has seriously affected the benefits of shale gas development and remains to be solved for many years. In this paper, based on the analyses of Multi-finger Imaging Tool-24 (MIT-24) data, microseismic data, and the relationship between CD and engineering parameters, we confirm that the wellbore morphology in all CD sections in the Weiyuan area is consistent with shear deformation characteristics and clarify the cause of all CD: hydraulic fracturing leads to increased fluid pressure in well-intersecting faults and large fractures (F-Fs), inducing their shear slip, and eventually leads to asymmetric compression on the casing by strata on both sides of F-Fs, i.e., CD. On this basis, we propose a set of methods to control (or moderate) the shear slip of F-Fs by reducing the additional fluid pressure in target F-Fs during hydraulic fracturing to prevent CD, including multi-cluster perforations, temporary plugging F-Fs and fracturing fluid flowback. We also analyze the theoretical basis, feasibility and workflow of these methods. These methods have been tested in 44 horizontal wells in the Weiyuan area, of which the result is a radical decrease in the CD rate of the single well (from 54% to 9.1%), indicating that the slip of F-Fs and the resulting CD during hydraulic fracturing can be controlled and providing a reference for the prevention of hydraulic fracturing-induced earthquakes. • All CD during hydraulic fracturing of shale gas in the Weiyuan area is caused by induced shear slip of F-Fs. • Temporary plugging can reduce the additional fluid pressure in target F-Fs so as to prevent CD. • The integrated technical methods have been proved to be effective in preventing CD in field application. [ABSTRACT FROM AUTHOR]

Breakthroughs in shale gas exploration in the Upper Ordovician-Lower Silurian strata of the Upper Yangtze Platform have attracted interest in its sedimentary-tectonic evolution, but the tectonic background of the northern margin of the Upper Yangtze Platform remains unclear. In this paper, the Wufeng-Longmaxi formations on the northern margin of the Upper Yangtze Platform were investigated. Based on geochemical and mineralogical analyses of the tuffs/K-bentonites of the Wufeng Formation and the barite in the Longmaxi Formation, as well as previous research results, it was concluded that the northern margin of the Upper Yangtze Platform was in an extensional tectonic background during the Late Ordovician-Early Silurian. Detailed analysis revealed that, (1) the U–Pb zircon age of the tuff in the Bajiaokou section in South Qinling is 443.91 ± 0.92 Ma. The Zr/TiO 2 –Nb/Y diagram of the tuffs/K-bentonites indicates that their protoliths were alkaline-subalkaline basalt and andesite series rock. Based on the Th–Hf/3-Ta, Th–Tb*3-Ta*2, and TiO 2 –Nb/3-Th diagrams, there are undiscovered intraplate tension calc-alkaline basalts in the northern Yangtze Platform or the southern Qinling region, which provided volcanic clastic materials to the Ziyang, Lan'gao, Chengkou, Yichang and other regions. (2) Scanning electron microscopy revealed that the barite crystals in the Longmaxi Formation exhibit dissolution features and have a large particle size. Energy spectrum analysis of these barite crystals revealed that they have C, O, S, and Ba contents of 8.48 wt%, 22.98 wt%, 13.09 wt% and 55.44 wt%, so they are speculated to have been formed via cold methane seep genesis in a weak extensional tectonic setting. The 87Sr/86Sr ratios of the barite revealed that different types of barite were simultaneously formed in this area under the influences of hydrothermal and cold methane seeps. (3) The analysis of the heavy minerals in the Lower Silurian strata in the Bajiaokou section revealed that the provenance in the South Qinling area changed significantly during the late Early Silurian. Based on the above analyses, the northern margin of the Upper Yangtze Platform was in an extensional tectonic setting during the Late Ordovician-Early Silurian. The distribution of the total organic carbon content indicated that the extensional tectonic background provided good conditions for the enrichment and preservation of organic matter. The results of this study provide an understanding of the regional sedimentary-tectonic pattern and evolution of the Yangtze Platform during this period, as well as a reference for future shale gas exploration in this region. • The tectonic background of the Late Ordovician-Early Silurian was studied. • The northern margin of the Upper Yangtze Platform is an extensional background. • The extensional tectonics caused the cold seepage events. • The extensional fault controlled the distribution of volcanic clastic sediments. • Organic matter accumulation was influenced by the extensional fault depression. [ABSTRACT FROM AUTHOR]

• The desorption mechanism of oil from the nano-micro pores was studied. • The oil is desorbed when the particle self-rotation speed is faster than the critical speed. • When the inlet flow rate increased, the particle self-rotation speed increased, which could strengthen the desorption process. To realize the harmless treatment and resource recycling of oily shale cuttings, the most important step is to desorb the oil phase from the pores of the cuttings. The desorption treatment must overcome the capillary force and viscous resistance inside the pores. This paper discusses a cyclone oil desorption technology. The particles of the oily shale cuttings in the swirl field generated by the cyclone will have high-speed self-rotation, thus providing sufficient centrifugal forces that separate the phase oil from the pores. The critical speed of such self-rotation for the desorption of oil phase in pores of particles was analyzed using mechanical formula, and the distribution of particle self-rotation speed in the cyclone was calculated and simulated. We collected shale cutting samples from the Sichuan shale gas field in China. Experiments were conducted to observe the changes in the porosity and oil content of the cuttings before and after cyclone desorption treatment. The results show that the particle self-rotation in the cyclone can effectively achieve the oil phase desorption from the particle pores. For the shale cuttings in the experiments, when the particle self-rotation speed is faster than the critical self-rotation speed of 507 rad/s, the oil phase in the particle pores can be desorbed. When the inlet flow rate is between 55 m3/h − 95 m3/h, the particle self-rotation speed is faster than the required critical self-rotation speed. As the inlet flow rate increases, the particle self-rotation speed in the cyclone also increases, which generates better desorption effects. [ABSTRACT FROM AUTHOR]

[Display omitted] • The shale gas resource potential of the Longmaxi Formation was evaluated by using mud gas isotope logging technology. • The reservoir properties of shale were evaluated based on gas isotope fractionation effects. • The shale gas in the Changning area belongs to late kerogen cracking gas. • The lower part of the Longmaxi Formation has a better shale gas exploration potential. The Longmaxi Formation in the Sichuan Basin is one of the most important shale gas producing formations in China. Previous studies of shale gas were mostly carried out on based on laboratory analyses and did not provide effective guidelines for shale gas exploration. In this paper, we present a large amount of carbon isotopic data from mud gas isotope logging and rock-cutting headspace gas in wellsites. The δ13C 1 values showed a significant decrease at the bottom of the Longmaxi Formation. The δ13C 1 and δ13C 2 values in the Changning area were observed to be heavier than those in the Weiyuan and Jiaoshiba areas. The second half of the N216H27-3 horizontal well had obvious outgassing and carbon isotope fractionation effects. This indicates that the bottom of the Longmaxi Formation has better shale gas exploration potential. The shale gas of the Longmaxi Formation in the Changning area belongs to late kerogen cracking gas, where exploration prospects are poorer than those in the Weiyuan and Jiaoshiba areas. There were more oil cracking gas resources and better reservoir conditions at the end of the N216H27-3 horizontal well; therefore, drilling should be continued at this site. [ABSTRACT FROM AUTHOR]

With the development of exploration and exploitation technologies, deep shale gas systems are gradually becoming an important target for the future petroleum industry. However, there is still a lack of systematic geological studies for deep shale gas systems, which restricts further exploration. In this paper, the deeply buried shales (more than 4000 m in depth) of the first member of Silurian Longmaxi (S 1 l1) at the southeastern margin of the Sichuan Basin are selected as the research object, and thin sections, scanning electron microscope (SEM) observations, total organic carbon (TOC) testing, nitrogen adsorption (NA), and major and trace element analyses are used to systemically identify the different lithofacies and delineate geological and geochemical features. Moreover, we reconstruct the paleoenvironment, summarize the controlling factors and mechanisms of organic matter accumulation and pore formation, and finally reveal the favorable exploration lithofacies. Our results show that there are four lithofacies that can be identified in deep S 1 l1 shale, namely, laminated organic-rich siliceous shale (S), laminated organic-rich mixed shale (RM), banded organic-lean mixed shale (LM), and banded organic-lean argillaceous shale (CM). Organic matter-hosted pores are the primary type in their pore system. The S and RM shales were mainly deposited under dysoxic to anoxic conditions with moderate watermass restriction, low terrestrial detrital influx, and high paleoproductivity, and the silica mainly originated from the diagenesis process (biogenic quartz); the LM and CM shales were sedimented under oxic conditions with high terrestrial detrital influx and low paleoproductivity, and the silica mainly originated from terrestrial detrital influx. Redox conditions, paleoproductivity, and terrestrial detrital influx together controlled the organic matter enrichment in the deep S 1 l1 shale, and the TOC content further influences the physical properties of the shale, thus determining the exploration potential of different lithofacies. Moreover, the significant impacts of lithofacies on the geological and geochemical features of the deep shale gas system are demonstrated. Compared with the middle-shallow shale gas system in the study area, due to less tectonically uplifted and tectonically active shale, the deep shale has more extraordinary preservation conditions, overpressure inheritance development, and higher gas amounts. The S and RM in S l l1 in the study area have better resource potential and should be given more attention in the future. • Geological and geochemical features of different lithofacies in deep shale gas systems are systematically characterized. • Paleoenvironment, organic matter accumulation, and pore formation mechanisms of different lithofacies are revealed. • Lithofacies has a considerable influence on the deep shale gas system, which is consistent with the system in shallow-middle depths. • Compared with shallow-middle shale gas systems, deep shale gas accumulations are generally characterized by overpressure, which leads to a high gas amount. • Overpressure may be due to variations in tectonic activity and preservation conditions. [ABSTRACT FROM AUTHOR]

The Longmaxi Formation has abundant shale gas resources. High-yield wells have been obtained in medium-shallow and deep areas in the Sichuan Basin. Quantitative research on the brittle-ductile change in rocks is a basic geological component for caprock evaluation, and it can also be applied to shale gas exploration. This paper fully considers the difference between the lower shale (N1) and upper shale (N2) of the Longmaxi gas-bearing shale. Through total organic carbon (TOC), mineral components, field emission scanning electron microscopy (FE-SEM), and triaxial mechanics experiments, the two groups of shale samples, N1 and N2, were compared and analyzed, and the brittle-ductile transition was quantitatively studied. Based on previous work, a method for the fast calculation of the key over consolidation ratio (OCR) was proposed. The results show that N1 is mainly organic-rich siliceous shale, N2 is primarily organic-poor clay shale and mixed shale, and N1 is generally more brittle than N2. The key OCRs of N1 and N2 are 2.16 and 2.60, respectively. The key confining pressures at which N1 and N2 become fully ductile are 87.87 MPa and 70.28 MPa, respectively. Therefore, the key depths of the brittle zones of N1 and N2 (H b1 and H b2) and the key depths of the ductile zones of N1 and N2 (H d1 and H d2) are obtained. On this basis, a comprehensive model for the Longmaxi shale gas' brittle-ductile transition exploration zone in the Sichuan Basin and H b1 and H b2 maps of the Longmaxi gas-bearing shale have been established. Through comprehensive vertical and horizontal analysis, Longmaxi shale gas exploration risks in different blocks of the Sichuan Basin have been clarified. Therefore, this study of the variation in the brittle-ductile transition has an important guiding role in refining the exploration of Longmaxi shale gas in the Sichuan Basin. • There are obvious differences between the lower shale and the upper shale. • Difference of brittle-ductile transition makes shale gas exploration more complicated. • The new method can quickly calculate the threshold value of over consolidation ratio. • The new model provides more comprehensive guidance for shale gas exploration. [ABSTRACT FROM AUTHOR]

The estimated ultimate recovery (EUR) of a single shale gas well is one of the important evaluation indicators for the scale and benefit development of shale gas. Nevertheless, due to the lack of engineering and geologic data, as well as the limitations of the existing empirical methods, the current production forecasting methods cannot make reasonable predictions for EUR. Therefore, Duong method is used as the prototype in this paper, a rapid and accurate empirical model for improved production prediction is proposed based on the historical production profile analysis of mass producing wells in Sichuan Basin. The accuracy and universality of the new model are verified by production examples in the Weiyuan, Changning, Luzhou and Yuxi blocks of the Sichuan Basin. The examples illustrate that the new model can be applied well in typical wells, and has no limitation of flow regimes for the production prediction of gas wells. In order to solve the problem of production data fluctuation and decline curve deviation caused by stimulation measures in the production process, a multi-segment production prediction model analysis method is proposed based on the improved model in this study and has been well applied in the field. Most importantly, the new model has clear physical parameters and is easy to operate. Performance of the new model based on production data is as reasonable as the modern production decline methods (including analytical model), which is better than existing empirical methods. • Proposing an improved empirical model, which is rapid and accurate. • Less parameters were selected, the new model still has clear physical meaning. • Application condition of the new model is not limited by the flow regime. • Performance of the new model based on production data is as reasonable as the analytical model. • Multi-segment production prediction model is well applied to gas wells with production data fluctuation. [ABSTRACT FROM AUTHOR]

The upper Permian Longtan Formation (LTF) shale is a new shale gas exploration and development focus in China, which was formed in a transitional depositional environment. Because of the difference in the sedimentary environment between marine-continental transitional shale and marine shale, the enrichment characteristics and mechanism of organic matter (OM) are very different. Because of a weak research foundation, the enrichment mechanism of OM in the LTF shale in the Sichuan Basin is still unclear. In this paper, shale samples of the upper Permian LTF from the Well F5 were collected, and the abundance, source and sedimentary environment of organic matter were studied by using paleoclimate, detrital input, redox, paleoproductivity and sedimentation rate parameters. The results show that the TOC content of the LTF shale is high (average = 3.04%) and reaches the high to overmature stage (average = 2.46%), indicating a favorable source rock. The LTF shale was deposited in a humid and hot climate, which was conducive to the growth and prosperity of a large number of plants. The source of organic matter was mainly terrestrial plant fragments. The sedimentary environment of the LTF shale was oxic, it had a high sedimentation rate, which reduced the oxidation rate of OM, promoted the rapid deposition of OM, and ensured the preservation of organic matter. In summary, the enrichment of OM of LTF shale in the Sichuan Basin was affected by the sedimentary environment, which was complicated. The main controlling factors were detrital input, redox conditions and sedimentation rate. • The geochemical characteristics of Permian Longtan Formation (PLTF) shale in eastern Sichuan are analyzed. • The sedimentary paleoenvironment of PLTF shale in eastern Sichuan is reconstructed. • The main controlling factors of organic matter enrichment of PLTF in eastern Sichuan are studied for the first time. [ABSTRACT FROM AUTHOR]

The lamellation fractures in marine shales are important to the accumulation and preservation of shale gas, whose characteristics and controlling factors are still unclear. This paper focus on the characteristics descriptions and controlling factor analyses based on core observations, thin sections, and scanning electron microscope (SEM) experiments. The marine shales of Paleozoic Wufeng Formation and Longmaxi Formation in the Fuling Area of Eastern Sichuan Basin are taken as an instance. The lamellation fractures are occurring along the direction of the lamellations, partially of them curved, bifurcated, and converged. The apertures of fractures typically range from 1 to 500 μm. Only a few (<1%) lamellation fractures are filled with quartz, calcite, pyrite, and bitumen. After a series of analyses, developments of lamellation fractures are controlled by total organic carbon (TOC), brittle minerals, laminae, and pyrite. (1) The organic matters control the formation and evolution of lamellation fractures by generating gas and resulting in overpressure. An increase in the TOC content of 1% can increase the lamellation fracture density by 0.26 cm-1. (2) Brittle minerals, especially authigenic quartz, is also an important controlling factor to the development of lamellation fractures. When BI increases by 10%, the lamellation fracture density increases by 19%. (3) Besides, siliceous and carbonate laminae in the shale are more suitable for lamellation fractures to develop. When the laminae density is smaller than 4 cm−1, it is easier to develop lamellation fractures with higher laminae density. However, too densely-distributed laminae will suppress the formation of lamellation fractures. (4) Higher pyrite content is good for the development of lamellation fractures. Lamellation fracture density will increase by 9%, with pyrite content increased by 1%. For the shale at the bottom of the Wufeng Formation - Longmaxi Formation, lamellation fractures develop extensively due to the high TOC and pyrite content, great brittleness, and moderate laminae density. The density of lamellation fractures decreases from the bottom to the top. • Quantitative characterize about development characteristics of the lamellation fractures. • The lamellation fractures is controlled by brittle mineral, TOC, laminae and pyrite. • TOC is the main one that affects the development of lamellation fractures. • Clarify vertical distribution characteristic of lamellation fractures in the Wufeng-longmaxi Fm. [ABSTRACT FROM AUTHOR]

• CO 2 and SRB were the main factors of shale gas pipeline corrosion and perforation. • Pre-cultured with culture medium increased the corrosion rate of the steel, and SRB catalytic corrosion process. • CO 2 promotes bacterial film formation and accelerates corrosion. • Bacterial enrichment is the main cause of pitting corrosion. In the shale gas field in southern Sichuan Basin, the corrosion-induced failure has been observed. In this paper, first, the corrosion phenomenon was analyzed. Second, the causes of corrosion were analyzed thoroughly from the aspects of corrosive environment, materials, and corrosion products. Finally, the field water environment was simulated, and the result showed the following: SRB is one of the main causes of corrosion and perforation of shale gas pipelines, bacterial enrichment is the primary reason for local corrosion, and CO 2 promotes the formation of bacterial film and accelerates corrosion. [ABSTRACT FROM AUTHOR]

The Lower Cambrian Qiongzhusi Formation source rock is one of the main sources of oil and gas in the Sichuan Basin. Owing to the controversial thermal history and the complex structural pattern in the Sichuan Basin, it is difficult to characterize the differences in maturity evolution and the timing of hydrocarbon generation periods of Qiongzhusi hydrocarbon source rocks in different tectonic zones. Based on the comprehensive analysis of the previous thermal history and denudation studies from the tectonic units of the basin, the thermal histories and denudation amount in main period of tectonic movement of a five-part tectonic development are obtained in this paper. Although the thermal history of different tectonic units varies, generally, the heat flow increased slowly in the early Paleozoic, and it experienced a peak heat flow at the end of the Middle Permian and decreased subsequently. Based on new thermal history and denudation data, the maturation of the Lower Cambrian Qiongzhusi Formation source rocks in the Sichuan Basin were modeled and their evolution can be classified into three patterns, which are: (1) continuous heating pattern in southern Sichuan, (2) Silurian-Permian heating cessation pattern in western Sichuan and northwest central Sichuan, and (3) Silurian-Permian and Triassic heating cessation pattern in the central uplift, northern structural zone and western part of the eastern structural zone. In addition, the key hydrocarbon generation periods of different tectonic units were determined in this study. Tectonic and sedimentary burial, together with high heat flow values during the Late Permian, were the main factors controlling levels of thermal maturity and thermal evolution models of the Qiongzhusi Formation. The present-day thermal maturity of the Qiongzhusi Formation depends on the thermal history and maximum burial depth before uplift in Late Cretaceous. However, the maturity evolution pattern affecting the key hydrocarbon generation stage was mainly related to the burial histories of source rocks in the Paleozoic. The thermal modelling of this study provides new evidence for the source rock evolution and new insight into Lower Paleozoic shale gas. • Thermal history, denudation amount and process of different tectonic units are summarized. • Maturity evolution and key HC generation periods of the Qiongzhusi Formation are obtained. • Three thermal evolution patterns of source rocks are classified. [ABSTRACT FROM AUTHOR]

Shale gas development in the Sichuan-Chongqing region in China has experienced a high level of casing deformation or failure during hydraulic fracturing treatment, which has resulted in significant productivity decline and economic losses. This problem has motivated many studies in the literature but focusing on the shearing deformation using the finite element method. This paper categorizes the casing failure modes and mechanisms in the region and presents casing collapse laboratory results. The designed laboratory tests rendered us critical data points in casing deformation under different loading scenarios. For multiple stage hydraulic wells in the region, we propose to use a strain-based protocol for casing design instead of the current design based on maximum stress. • Present laboratory experiments on casing deformation due to shearing stress. • Propose a model to predict the maximum allowable stress for a casing tubular. • Update statistics on casing deformations and failures in the Changning-Weiyuan region. • Introduce one of a kind laboratory experiment setup for full size tubular testing. [ABSTRACT FROM AUTHOR]

The growing research on the features of shale pore structures has deepened the understanding of shale oil and gas storage capacity. Nevertheless, few studies have focused on the differences of the specific parameters that are characteristic of the nanopore structure in shales with different lithofacies. Such parameters include the full-scale ranges of the pore specific surface area and pore volume distribution, porosity and fractal dimension. In this paper, a dozen Longmaxi Formation shale samples from the southern Sichuan Basin were studied to determine the differences in these parameters. A set of laboratory experiments were performed, such as geochemical experiments, X-ray diffraction, N 2 and CO 2 isothermal adsorption, mercury injection capillary pressure tests and scanning electron microscopy experiments. The results of this study indicate that shale samples can be classified into 5 types of lithofacies based on their mineral composition. The surface porosity of organic matter particles is 8–16 times greater than that of mineral particles. The major contributors to the pore volume and surface area of shale samples are mesopores and micropores, respectively. The full-scale pore size distribution is mainly from 0.4 to 0.6 nm, 2–7 nm, and 10–20 nm for the pore volume and from 0.3 to 1.0 nm and 1.5–7 nm for the pore surface area. The average values of the porosity, fractal dimension, pore volume and pore surface area of the M-2 shales are almost equal to those of the S group shales. This result indicates that the M-2 shale has a large gas storage capacity similar to that of shales with siliceous lithofacies. The development of organic matter pores that contribute to more than 50% of the porosity leads to the high porosity and fractal dimension of the M-2 shales and S group shales. In addition to organic matter, illite minerals also play an important role in the constitution of the majority of the storage space in the CM-1 shale. • Full-scale pore structure of shales with different lithofacies were contrasted. • The smaller the pore size, the stronger the heterogeneity of shales. • Porosity minerals and OM accounted for in different shales were quantified. • Except for OM, illite is another important factor to pore development. [ABSTRACT FROM AUTHOR]

The Upper Ordovician Wufeng Formation and Lower Silurian Longmaxi Formation marine shale are the major shale gas exploration and development target in the Middle-Upper Yangtze region. Although three national shale gas demonstration areas have been built and several high-yield shale gas wells have been discovered in the Wufeng Formation and Longmaxi Formation, shale gas in these areas has not been fully commercialized because the enrichment degree of shale gas varies greatly in different tectonic settings. By analyzing the formation processes and distribution characteristics of the organic-rich shale, reconstructing the burial history and hydrocarbon generation history, and comparing the shale gas enrichment and preservation conditions in different tectonic settings in South China, this paper points out that (1) The craton depression and foreland basin on the cratonic margin are favorable zones for the development of organic-rich shale. Because the Yangtze plate is small, the foreland basin is greatly affected by the input of terrigenous clastic and the thickness and area of organic-rich shale in the craton basin is larger than that in the foreland basin. The organic-rich shale is mainly distributed in south Sichuan deep-water shelf and west Hubei-east Chongqing deep-water shelf, and the enrichment interval is the Dillcellograptus complexus-Cystograptus Vesicolus graptolite zone from the Wufeng Formation to the bottom of Longmaxi Formation are favorable intervals for shale gas enrichment. (2) Since the Late Jurassic, significant differential intracontinental tectonic deformation, uplift and denudation occurred in the Middle-Upper Yangtze region. Moderate compression and uplift were beneficial to the development of micro-fractures and bedding fractures in shale, resulting in good preservation conditions of shale gas reservoirs with a high-pressure coefficient. In contrast, strongly deformed areas, where faults and high-angle large fractures were developed, are not conducive to the preservation of shale gas reservoirs. (3) The craton depression of the Middle-Upper Yangtze region, where organic-rich shale was deposited, is favorable to shale gas enrichment because it provides a good material basis, and also a relatively stable and compression-resistant tectonic environment for later tectonic deformation and uplift-derived destruction. Based on the analysis and evaluation of tectonic construction–transformation conditions under the macro-control of plate tectonics, it can well explain the existing commercial shale gas discoveries and failure cases and can guide the optimization of future exploration targets. • ►Deep water in the craton depression controlled the distribution of organic-rich shale. • Stable tectonic settings are favorable for shale gas enrichments. • Two depressions in Yangtze Craton are the most favorable areas for shale gas accumulation. [ABSTRACT FROM AUTHOR]