Search

Upconversion nanoparticles (UCNPs), particularly those that are highly doped, possess outstanding properties and have demonstrated tremendous application potential. However, novel fine-tuning strategies are urgently required to enhance the upconversion luminescence (UCL) performance of UCNPs. In this study, a series of core–multishell UCNPs highly doped with Ho3+ and Yb3+ ions were synthesized via the oleate route. The X-ray diffraction (XRD), transmission electron microscopy (TEM), and UCL spectra and decay times, and pump power dependency of the synthesized UCNPs were used to examine their morphology, size, and the UCL properties. Ce3+ ions were introduced to enhance Ho3+-based red UCL, and their doping strategy was also optimized based on summarized UCL trends and detailed UCL mechanism analysis. NaHoF 4 :Gd3+@NaGdF 4 :Yb3+,Ce3+@NaGdF 4 :Yb3+ UCNPs that had 10 mol% Ce3+ dopants in their middle shells exhibited better UCL properties than the larger traditional NaGdF 4 :Yb3+,Ce3+,Ho3+ UCNPs, probably because of the combined influence of the energy interactions between the Ce3+ ions and surface groups, sensitizing energy enhancement by active shells, and the positive cooperation between the Ce3+ ions and highly-doped core–shell structures. In this study, the phenomenon of UCL decrease resulting from Ce3+ ion doping was explored. Using unique core–multishell structures with highly-doped activators and sensitizers placed within and outside the structures, respectively, the UCL decrease due to Ce3+ ion doping was attributed to a competition for photons. Doping the UCNPs with Ce3+ ions near the UCNP surfaces favors Ho3+-based red UCL. Our study findings can deepen the understanding of the Ho3+-based UCL mechanisms and increase the potential uses of NaHoF 4 materials in photo-induced therapy. When Ce3+ ions are doped near the nanoparticle surface, they might have energy interactions with surface groups to relieve phonon energy shortage and thus enhance the efficiency of cross-relaxation between Ho3+ and Ce3+ ions. [Display omitted] [ABSTRACT FROM AUTHOR]

Scintillators, owing to their exceptional ability to convert high-energy ionizing radiation into visible light, are the core component of X-ray radiography. However, conventional single-crystal scintillators are inadequate to satisfy the modern social and scientific demands. So, the development of novel scintillator materials is imminent. Herein, a series of Na 5 Lu 9- x Gd x F 32 :Ce3+ glass-ceramics (GCs) scintillators were elaborated by an exercisable and low-cost method. Benefiting from the proper introduction of Al powder and Gd3+, as well as the crystallization of Na 5 Lu 9- x Gd x F 32 nanocrystal (NCs) after heat treatment, luminescence excited by ultraviolet and X-ray of the sample is enhanced significantly. The integrated X-ray excited luminescence intensity of the representative sample can reach up to 128% of that of Bi 4 Ge 3 O 12. More importantly, the sample has excellent irradiation stability that is almost undamaged even exposed to high-energy X-ray radiation. Finally, satisfactory X-ray imaging based on the resultant sample was realized. The spatial resolution is as high as 14 lp mm−1, which exceeds that of many novel perovskite scintillators. Thus, this investigation promotes the development of low-cost, stable and high-performing Ce3+-activated GCs scintillators. • Three effective ways were designed to improve the scintillating property of the sample. • The integrated X-ray excited luminescence reaches 128% of that of Bi 4 Ge 3 O 12. • The sample is undamaged even excited by high-power (12 W) X-ray, infering outstanding irradiation stability. • Satisfactory X-ray imaging based on the sample was achieved. • The spatial resolution reaches 14 lp mm−1, exceeding that of many perovskite scintillators. [ABSTRACT FROM AUTHOR]

Er3+ doped high density germanate glasses with compositions of 50GeO 2 -10BaO–10Al 2 O 3 -15Lu 2 O 3 -(15-x) La 2 O 3 -xEr 2 O 3 (x = 0, 0.1, 0.5, 1.0, 1.5, and 2.0, in mol%) have been prepared by the melt-quenching method. The optical and physical properties of the samples were characterized by differential scanning calorimetry (DSC), density, transmittance spectra, photoluminescence (PL) spectra, and X-ray excited luminescence (XEL) spectra. The densities were in the range from 5.90 to 6.07 g/cm3. The strong green emissions around 552 nm of Er3+ were observed upon the excitations of 378 nm light and the X-ray, and the lifetimes of 552 nm emission were in the range of 20.88–96.47 μs. The results show that Er3+ doped high density germanate glasses could be used as potential scintillators for X-ray CT. [ABSTRACT FROM AUTHOR]

We report a study of composite scintillating ceramics based on coupled layers of two different garnets, namely Ce-doped gadolinium gallium aluminium (GGAG:Ce) and Pr-doped yttrium aluminium (YAG:Pr), fabricated by hot isostatic pressing. Two samples were prepared, with different GGAG:Ce layer thickness, 120 µm and 690 µm respectively, but with a comparable overall thickness of 1.4 mm. The key finding is that the material architecture strongly determines the scintillation response. The radioluminescence is that expected from the irradiated material when a thick layer of ceramic is exposed to X-rays. Conversely, exposing a thin layer allows a non-null probability —about 0.3% for 120 µm of GGAG— of finding an X-ray photon in the underlying layer, and thus radioluminescence from both materials is recorded. We believe these results can extend the potential of layered optical ceramics for advanced devices, such as energy- and direction-sensitive X-ray detectors. [Display omitted] [ABSTRACT FROM AUTHOR]

The luminescence and scintillation properties of Ce3+ doped alkali phosphate glasses 56P 2 O 5 :8Gd 2 O 3 :5Al 2 O 3 :1CeBr 3 :30XCl (PGAC:X, X = Li/Na/K/Rb/Cs) were studied for their potential applications in gamma and alpha detection. In the Fourier Transform Infrared Spectroscopy (FTIR), X-ray Luminescence (XRL), Photoluminescence (PL), and transmittance spectra, the red shift was found and explained by the concept of optical basicity. Broad Ce3+ emission and energy transfer from Gd3+ to Ce3+ were observed in XRL and PL measurements. Scintillation performance was studied by irradiating the samples under 137Cs gamma and 241Am alpha sources. The fast, intermediate, and slow decay components under gamma and alpha excitation were found around 30, 200 and 3000 ns, respectively. The decay time increased slightly from PGAC:Li to PGAC:Cs, indicating the less effective transition from Gd3+ to Ce3+. The alpha decay time was longer than the gamma decay time, revealing the Pulse Shape Discrimination (PSD) capability of the glasses for particle identification. The XRL intensity reduced significantly from PGAC:Li to PGAC:Cs samples did not reflect the scintillation tendency. By successfully detecting gamma and alpha scintillation signals, the scintillation performance of all samples was found to be similar. In general, all samples can be used for gamma and alpha detection. Using Rb+ or Cs+ ions is favorable in terms of high density and light yield, while Li+ ions enhance the transmittance and homogeneity. Furthermore, a correlation between P–O–H groups within the glass matrix and scintillation performance was also observed. [ABSTRACT FROM AUTHOR]

The objective of this paper is to review the use of the thermoluminescence (TL) and optically stimulated luminescence (OSL) techniques as research tools in luminescence, particularly to detect the presence of trapping centers that can degrade the efficiency of scintillators, and shape the properties of persistent phosphors, storage phosphors and dosimeters. A brief review of the main analysis techniques is provided, followed by a discussion of their limitations. Examples of applications in which the TL or OSL analyses have provided useful information on the trapping and recombination of charges created by ionizing radiation is given. [ABSTRACT FROM AUTHOR]

Micron/sub-micron hard X-ray imaging is an important development direction of X-ray detection technology. Scintillation screens with excellent X-ray stopping power and high light output are desired to obtain good imaging quality. Europium-doped lutetium oxide (Lu 2 O 3 :Eu) film with micro-columnar structure is an ideal candidate for this application. In this study, micro-columnar structured Lu 2 O 3 :Eu films were prepared on quartz glass substrates by laser chemical vapor deposition (LCVD) method. The influences of preparation conditions on structure and morphology properties of films were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Photoluminescence and scintillation properties of the films, including photoluminescence excitation (PLE), photoluminescence (PL), PL decay, X-ray excitation luminescence (XEL), and afterglow curves, were recorded. The relationships between structure, morphology, luminescence properties of films, and preparation conditions were investigated and discussed as well. The preparation conditions include laser power, oxygen flow rate, and precursor evaporation temperature. In addition, dual-layer Lu 2 O 3 :Eu film was prepared for the first time by just turning off the laser. [ABSTRACT FROM AUTHOR]

It is well known that scintillator performance, especially its energy resolution, is highly dependent on its homogeneity which is determined through its growth process. Therefore, examination and quality control of synthesized scintillators is an important step towards their improvement. Ionoluminescence (IL) microscopy is a highly sensitive and non-destructive technique which can reveal the texture, chemical composition and distribution of trace elements in the inhomogeneous specimens. In this research work, IL microscopy technique is employed for the first time to provide images of two synthesized CsI(Na) crystals. The results show that IL microscopy is not only capable of determining the distribution of the total luminescence emitted from each point, but can also determine it for individual luminescence bands, which represents special luminescence centers in the sample. Therefore, IL microscopy is introduced as a high potential technique for effective characterization of scintillators. [ABSTRACT FROM AUTHOR]

The study deals with the use of different amounts of MgO or tetraethyl orthosilicate (C 8 H 20 O 4 Si, TEOS), from 0.04 wt %, 0.06 wt %, 0.08 wt %, 0.4 wt %, 0.6 wt % to 0.8 wt %, respectively, as additional sintering aids during the vacuum sintering of transparent Ce3+ doped Y 3 Al 5 O 12 (Ce:YAG) ceramics to investigate their effect on microstructure and luminescence properties. A comparative study was carried out by using X - ray diffraction, scanning electron microscopy/energy dispersive X - ray spectroscopy, optical and photo-luminesce spectra, as well as electroluminescent spectra. The dominant garnet phase was obtained even when adding 0.8 wt % of MgO or TEOS, while adding MgO led to finer average grain size (∼ 5 - 10 μm) and more homogenous distribution compared to TEOS (∼ 20 - 25 μm) in Ce:YAG ceramics. Adding a large amount of MgO was found to result in the segregation of MgO in Ce:YAG ceramics, while an excess of TEOS led to the segregation of Al 2 O 3. A strong absorption peak at 308 nm was observed in Ce:YAG ceramics with MgO sintering aids, which was ascribed to the existence of Ce4+ induced by a charge compensation effect of Mg2+. The optimum transmittance reached 80% @ 800 nm in Ce:YAG ceramics when adding 0.6 wt % TEOS, which also exhibited a maximum luminous efficacy of 106 lm/W. Si4+ was experimentally proved to have a better optimization effect on luminous efficacy compared to Mg2+. • MgO or TEOS (C 8 H 20 O 4 Si) was added as additional sintering aids in a wide amount range. • MgO proves to have distinct inhibit effect on the grain growth. • Better luminous efficacy were observed in ceramics with TEOS additives. [ABSTRACT FROM AUTHOR]

Pr3+ doped high density germanate glasses were prepared by the melt-quenching method. The physical and luminescent properties were investigated. The glass containing BaF 2 represented maximum phonon energy of 810 cm−1, and the glass density was greater than 6 g/cm3. The glass exhibited good radiation resistance under 2 h of X-ray irradiation. Intense blue, green emissions and weak red emissions were observed when the glass was excited by X-ray, and the blue fluorescence lifetimes were in the range of 9.15–12.59 μs The results show that Pr3+ doped germanate glass could be a potential scintillating material in the field of X-ray detection for fast events. [ABSTRACT FROM AUTHOR]

Oxyfluoride glass ceramics with low toxicity, high stability and strong X-ray excited luminescence intensity are introduced as scintillating material. Herein, a series of novel NaGd 2 F 7 :xTb3+ (x = 0, 0.1, 0.2, 0.3, 0.4) were synthesized through in situ growth self-crystallization. X-ray diffraction, fourier transform infrared spectrometer and transmission electron microscopy were measured to investigate the structure and morphology of NaGd 2 F 7 glass ceramics. These investigations demonstrate that NaGd 2 F 7 nanocrystals are uniformly distributed in glass matrix with 20–30 nm diameter. Photoluminescence and X-ray excitation spectra are greatly enhanced after further thermal treatment which verify better crystallization of NaGd 2 F 7 glass ceramics. The X-ray excited luminescence of the GC2–640 sample can reach 143.8% of the commercial BGO. More importantly, the damaged material can be completely repaired by annealing at 350 °C for 30 min. Our investigation indicates that Tb-doped transparent NaGd 2 F 7 glass ceramics are potential candidates of X-ray scintillating material. [ABSTRACT FROM AUTHOR]

The ability of a scintillator to absorb and convert the high-energy X-ray photons to low-energy visible photons is crucial for the application of X-ray in medical tests, security checks and scientific research. However, traditional scintillation crystals are synthesized by complex preparation process with high cost, hindering the wide development in practical applications. Here, Tb3+ doped sodium silicate glass, which exhibits remarkable scintillation property and recoverability to X-ray irradiation, was successfully prepared by an exercisable melt-quenching method. The obtained scintillator shows intense radioluminescence, which is about 1.5 times higher than that of the reference of Bi 4 Ge 3 O 12. The damaged glass to X-ray irradiation can be returned to the original state after heat treatment again, indicating excellent recovery. Moreover, the scintillator displays wonderful thermal stability with the fluorescence intensity at 573 K still remaining 96% at room temperature. These results demonstrate that the obtained scintillating glass has potential application towards the real world. [ABSTRACT FROM AUTHOR]

The photoluminescence and scintillation properties of n-bromophenethylammonium lead chloride ((n-BrPEA) 2 PbCl 4) (n = 4, 3, and 2) and phenethylammonium lead chloride ((PEA) 2 PbCl 4) have been investigated. All the samples showed broad emission peaks at 400–700 nm upon excitation by UV light or X-ray. The decay time constants of 8–28 ns were obtained which originated from the recombination of self-trapped exciton (STE) within inorganic layers. The afterglow levels at 20 ms after 2 ms of X-ray irradiation of (4-BrPEA) 2 PbCl 4 and (3-BrPEA) 2 PbCl 4 (76 and 55 ppm) were better than (PEA) 2 PbCl 4 (379 ppm). The light yield of (4-BrPEA) 2 PbCl 4 (3100 photons/5.5 MeV-α) was higher than (PEA) 2 PbCl 4 (1400 photons/5.5 MeV-α). • (BrC 6 H 4 C 2 H 4 NH 3) 2 PbCl 4 crystals were grown by the slow cooling method. • All the crystals showed the luminescence due to the recombination of the self-trapped excitons confined in inorganic layers. • The (4-BrC 6 H 4 C 2 H 4 NH 3) 2 PbCl 4 crystal showed the highest QY in the present crystals. • The light yields of the (4-BrC 6 H 4 C 2 H 4 NH 3) 2 PbCl 4 crystals surpassed that of the unsubstituted crystal. [ABSTRACT FROM AUTHOR]

Ce differently (0, 0.01, 0.1, 1, 2 and 5% with respect to Mg) doped LiMgAlF 6 ceramics were synthesized by the spark plasma sintering (SPS) method. In photoluminescence (PL), emission bands appeared at 300 nm with 30 ns day time, and these emission properties were almost the same in scintillation under X-ray irradiation. Further, thermally stimulated luminescence (TSL) was observed after X-ray irradiation, and the primary glow peak temperature was 160 °C with a lower detection limit of ∼10 mGy. • Ce-doped LiMgAlF 6 ceramics were prepared by the spark plasma sintering method. • Photoluminesence and scintillation properties were investigated. • Thermally stimulated luminescence properties were evaluated. [ABSTRACT FROM AUTHOR]

Intrinsic luminescence in Ce-doped (Lu,Y) 2 SiO 5 (or LYSO:Ce) single crystals have been studied by means of excitation luminescence spectroscopy in the vacuum ultraviolet energy range under synchrotron radiation. A previously unreported luminescence band with emission at 250 nm has been discovered as well as its thermal behavior was described in the temperature range 10–120 K. The excitation spectra as well as time-resolved properties of this band suggest that this emission corresponds either to the singlet component of self-trapped exciton or to a self-trapped exciton in the lutetium sublattice of LYSO single crystals. • New previously unreported intrinsic emission band at 250 nm has been observed in LYSO single crystals. • Temperature dependencies of intrinsic luminescence have been measured and analyzed. • Two possible origins of new 250 nm emission are proposed and discussed. [ABSTRACT FROM AUTHOR]

Ce,Mg:Lu 2 YGa x Al 5-x O 12 (x = 1.5, 2, 2.5, 3) ceramic scintillators were fabricated by oxygen sintering combined with air annealing using nano-powders synthesized by the co-precipitation method. The Ce3+ 5d 1 → 4f (2F 5/2 , 2F 7/2) luminescence band was blue shifted with increasing Ga content due to the decrease in the crystal field splitting of the 5d levels. At room temperature (RT), the decrease of photoluminescence decay time and scintillation decay time was observed with increasing Ga content. At 662 keV γ-rays, the sample Ga2 exhibited high light yield (LY) of 28,700 photons/MeV, fast scintillation decay times of 17.7 ns (17 %) + 45.7 ns (83 %), and good time resolution of ∼220 ps. At RT, the decrease of LY value for the samples Ga2.5 and Ga3 could be attributed to the larger thermal ionization of the excited Ce3+ centers. • Scintillation properties of Ce,Mg:Lu 2 YGa x Al 5-x O 12 (x = 1.5, 2, 2.5, 3) ceramics are investigated. • All ceramic samples show fast effective scintillation decay time less than 47 ns. • Sample x = 2 shows high LY of ∼28,700 ph/MeV @662 keV γ rays. • Samples x = 2 and 2.5 show good coincidence time resolution of 220 ps. [ABSTRACT FROM AUTHOR]

This study provided the first in-depth investigation of the effects of large dopant incompatibility (Pr3+ and La3+ ions) on the small host lattice element (Lu3+) in Lu 3 Al 5 O 12 (LuAG) single crystal. The growth of such complex crystals from the melt presented many challenges. By engineering the ionic radius ratio of RE- and M-site cations, a single-crystal phase stabilized by configurational entropy was achieved. This investigation elucidated the crystallization behavior of configurationally disordered rare-earth aluminum garnet oxide (Lu 1−x−y Pr x La y) 3 Al 5 O 12 from the melt and characterized its functional properties, including microstructural, optical, photoluminescence, and scintillation properties, between 5 and 300 K. Relaxation of the imposed strain energy led to local perturbations and destabilization of the garnet structure. Multielemental EDS mapping, micro-Raman spectroscopy, and thermoluminescence revealed the mechanism by which atomic size mismatch drove a smooth transition from the garnet to the perovskite phase in high entropy garnets. The optical, photoluminescence, and scintillation measurements provided fundamental insights into property changes driven by incompatibility doping. Standard and modified Judd-Ofelt theory analysis of absorption spectra determined the phenomenological Judd-Ofelt parameters Ω λ and radiative lifetimes. Atomic size mismatch engineering offers a promising approach to overcoming the limitations of conventional eutectic synthesis methods. • Perovskite inclusions, driven by atomic size mismatch, extend from rim to core. • Controlled incompatible La3+,Pr3+ codoping in LuAG modify functional properties. • Scintillation light yield improved up to 30% in La3+ codoped LuAG:Pr crystals. • (La,Pr)AlO 3 perovskite forms due to size mismatch of La3+ and Pr3+ with Lu3+. • Lattice disorder affects the intensity ratio of Pr³⁺ 5d→4 f and 4 f→4 f emissions. [ABSTRACT FROM AUTHOR]

Scintillators are of significance for X-ray excited luminescence (XEL) imaging from scientific research to medical diagnostics application. Rare earth fluoride nanocrystals possess distinctive luminescent properties originated from the abundant energy level of lanthanide activators, showing potential applications as next-generation scintillators. Herein, high Z atomic rare earth element lutetium was chosen to synthesized NaLuF 4 -based nanoscintillators by Tb doping. Core-shell structure was fabricated to further enhance the XEL emission intensity. The NaLuF 4 -based nanoscintillators was demonstrated more efficient XEL emission with 3-folds increase compared to NaYF 4 nanocrystals. NaLuF 4 nanocrystals with a 25 mol% Tb doping and an inert shell coating exhibited excellent scintillation performance with detection limit as low as to 57.05 nGy air s−1. X-ray imaging demonstrated a high spatial resolution of 10.5 lp mm−1 using a scintillator film made from as-prepared NaLuF 4 -based nanoscintillators. Finally, such NaLuF 4 -based scintillators film have been applied in X-ray imaging application for a chip and a biological specimen. This study proposed an effective strategy to enhance XEL for rare earth fluoride, providing the ability for high-quality X-ray imaging. • Enhanced luminescence of X-ray excitation nanocrystals were demonstrated by selecting NaLuF 4 -based and core-shell structure. • The nanoscintillators exhibited excellent X-ray scintillation performance, achieving efficient X-ray luminescence imaging. [ABSTRACT FROM AUTHOR]

X-ray Excited Optical Luminescence (XEOL) from rare earth doped whitlockite phosphates and silicate garnets [Ca 9 La(PO 4) 7 and Ca 9 Lu(PO 4) 7 , doped with 1 mol% Ce3+; Ca 3 Sc 2 Si 3 O 12, doped with 0.5 mol% Pr3+, 1 mol% Eu3+ and 1 mol% Tb3+], was obtained upon X-ray excitation with a tunable synchrotron light source. Excitation at photon energies across the M 5,4 -edge of the dopants reveals additional information not normally obtainable with conventional UV/visible or an X-ray line source (Al K α). It is found that despite the low concentration, photoluminescence yields excited with photon energy at the M 5,4 -edge of the rare-earth dopant can positively and negatively affect the overall energy transfer to the optical center. The implication of these observations is discussed. The application of XEOL in the investigation of X-ray scintillators is illustrated. [Display omitted] • X-ray Excited Optical Luminescence (XEOL) from rare earth doped phosphates and silicates is investigated. • Excitation at the M5,4-edge of the dopants reveals additional information not obtainable with UV/visible light. • Excitation at the M5,4-edge can positively and negatively affect the overall energy transfer to the optical channel. • The application of XEOL in the investigation of X-ray scintillators is illustrated. [ABSTRACT FROM AUTHOR]

(n-ClC 6 H 4 C 2 H 4 NH 3) 2 PbCl 4 ((n-ClPEA) 2 PbCl 4) (n = 2, 3, and 4) and (n-C 6 H 5 C 2 H 4 NH 3) 2 PbCl 4 ((PEA) 2 PbCl 4) crystals were synthesized by the slow-cooling method, and the photoluminescence (PL) and scintillation properties were evaluated. All the samples showed self-trapped excitons luminescence at 400–700 nm. The PL quantum yields of the (n-ClPEA) 2 PbCl 4 (n = 2, 3, and 4) and (PEA) 2 PbCl 4 crystals were 2.2, 0.9, 11.2, and 2.2 %, respectively. In the pulse-height spectra of 241Am α-rays (5.5 MeV), full energy absorption peaks were observed, and the light yields of (n-ClPEA) 2 PbCl 4 (n = 2, 3, and 4) and (PEA) 2 PbCl 4 crystals were respectively calculated to be 530, 490, 2,800, and 1,400 photons/5.5 MeV-α with typical errors of ± 10 %. [ABSTRACT FROM AUTHOR]

• CuI thin films have been synthesized in iodine solution at room temperature. • An apparent NBE peak can be recognized both in PL and XEL spectra. • Iodine-rich condition is beneficial to improve the XEL yield of CuI thin films. CuI is considered as a potential candidate for fast scintillator material due to the fast decay time. However, the ever-reported CuI scintillator usually demonstrates a more intensive deep-level emission with the decay time as long as 2.82 μs, which is unfavorable for the application as a fast scintillator material. In present work, γ-phase CuI were synthesized by iodizing Cu thin films in iodine solution at room temperature. An apparent near band-edge emission (NBE) is observed both in photoluminescence and X-ray excited luminescence spectra. By analyzing the variation of the relative intensity ratio of the sub-peaks composing NBE against different fabrication conditions, it can be deduced that Cu vacancy and surface chemisorbed iodine are responsible for the above luminescence behavior. It is hoped that these findings may boost the exploration of CuI thin films as fast scintillator materials. [ABSTRACT FROM AUTHOR]

Recent surge in additive manufacturing efforts demonstrate stereolithography as a promising technique for fabricating glass materials due to the high speed and scalability of the process. However, little efforts have been devoted to manufacture borosilicate glass by the stereolithographic process. One of the challenges is that its relatively low softening temperatures could interfere with the thermal post-printing process and introduce poor fidelity and structure instability. Here, we report on the first demonstration of stereolithographic manufacturing of cerium-doped (Ce-doped) (<10%) and undoped borosilicate glass which was enabled by a multi-step post thermal processing. The optical properties of the printed glass depend on thermal processing parameters (temperature, time, and environment) and can be readily tuned and optimized for a wide range of applications. The printed amorphous glass shows good structural stability with band gap of 3 eV, Urbach energy of 0.75 eV and refractive index of 2.14 for 8% Ce-doped glass, respectively. These results indicate Ce-doped glass fabricated by stereolithography is suitable for scintillator applications and that additive manufacturing could be promising for borosilicate glass fabrication. [ABSTRACT FROM AUTHOR]

All-inorganic perovskite quantum dots have been widely used in solar cells, LED, laser and scintillator in recent years. However, the essence of ion migration in perovskite lattice can cause the ion vacancies exist, which can directly affect the luminescence process. Herein, we focus on the effect of monovalent cation vacancies on the CsPbBr 3 lattice, and realize the adjusting lattice structure of the CsPbBr 3 QDs to change the luminescence lifetime by controlling the formation of monovalent cation vacancies. The results show that the existence of monovalent cation vacancies can be controlled by controlling dosages of Cs + precursor and can make the CsPbBr 3 lattice produce local lattice micro distortion and reduce luminescence lifetime, which is beneficial to realize the rapid and efficient X-ray imaging of scintillating crystals. Experimental result is also verified by density functional theory (DFT). [ABSTRACT FROM AUTHOR]

• (Gd 1-x Ce x) 3 (Ga 0.995 Cr 0.005) 5 O 12 single crystals were grown by micro-pulling down method. • The emission wavelengths of these crystals were approximately 730 nm. • Cr was segregated in the center part of the crystals. • The relationship between Cr segregation and emission intensity was investigated. • The correlation coefficients of thoes relationships were around 0.9. For the decommissioning of Fukushima Daiichi Nuclear Plants, a novel real-time dose-rate monitor consisting of a scintillator, 100-m long optical fiber and CCD spectrometer has been proposed, and this scintillation material is required to have an emission wavelength of longer than approximately 650 nm. In this paper, as a candidate material for the system, we focused on Ce/Cr co-doped Gd 3 Ga 5 O 12 (Ce/Cr:GGG) single crystals grown by the micro-pulling down method. Since the light output of this material was expected to depend on the Cr3+ concentration, we investigated the relationship between Cr segregation and luminescence properties in Ce/Cr:GGG crystal. Generally, a single photon counting method is not available to evaluate its light output accurately due to the long decay time, we used a novel technique "emission-intensity two-dimensional- mapping method" (2D-image method) to verify the light intensity at each point of the sample. This method realized estimation of the light intensity within the sample, though segregation of Cr3+ is observed. The results showed that Cr was concentrated in the center part along the radial direction in the grown crystals, while all parts had an emission wavelength of approximately 730 nm excited by X-ray. Using the 2D-image method, emission intensity was found to correspond to the Cr concentration, and its correlation coefficients between emission intensity and Cr concentration were over 0.8. We found that our material is available for the monitoring system when the Cr dense part of the crystal is cut and used. [ABSTRACT FROM AUTHOR]

• CeF 3 -doped CaF 2 transparent ceramics were fabricated by spark plasma sintering. • The transparent ceramics showed luminescence due to the 5d→4f transitions of Ce3+. • A direct correlation between scintillation light yields and TSL/OSL intensities was demonstrated. We report on the luminescence properties of CaF 2 transparent ceramics having various concentrations of CeF 3 (0.1 %, 0.5 %, and 1 %). Scintillation emissions centered at approximately 318, 345, and 386 nm derived from the 5d→4f transition of Ce3+ were detected, and scintillation light yields were determined to be 8600 photons/MeV (0.1 % CeF 3), 1930 photons/MeV (0.5 % CeF 3), and 1850 photons/MeV (1 % CeF 3) under gamma-ray irradiation from 241Am. The Ce-doped CaF 2 transparent ceramics showed thermally stimulated luminescence (TSL) with a broad glow peak at around 115–145 °C, and their dose response curves were determined over a broad dose range (0.01–3 mGy). Moreover, optically stimulated luminescence (OSL) exponential decay curves were obtained under 500 nm stimulation light, and dose response curves were obtained in the dose range of 0.1–100 mGy. The minimum detectable dose was estimated to be 0.1 mGy. A direct correlation between scintillation light yields under gamma-ray irradiation and TSL/OSL intensities was demonstrated. [Display omitted] [ABSTRACT FROM AUTHOR]

Cerium-doped lutetium yttrium orthosilicate (LYSO:Ce) powders were synthesized using the co-precipitation method. The influence of sintering temperature on the crystallization and luminescence characteristics of LYSO:Ce powders was investigated via X-ray diffraction (XRD) and photoluminescence (PL). The XRD measurements indicate that the crystallization of LYSO:Ce powders was affected by sintering temperature. PL results show that with the increase of sintering temperature, LYSO:Ce samples have better luminescence properties. A dosimeter was also fabricated using LYSO:Ce powders with 0.3 mol% Ce doping concentration for an optimum result. Radioluminescence properties of the radiation dosimeter were studied using calibrated 60Co gamma sources in the dose range from 232.66 to 1022.26 mGy. The results show that the dosimeter response under γ-rays irradiation has a certain linear response and stability, indicating its potential applications in remote radiotherapy and real-time radiation monitoring. • LYSO:Ce crystal powder as scintillitor material was synthesized by co-precipitation method. • LYSO:Ce with different sintering temperature has been systematically investigated. • A dosimeter was made with the optimal LYSO:Ce crystal powder for low dose gamma radiation. [ABSTRACT FROM AUTHOR]

(C 4 H 9 NH 3) 2 PbI 4 and (C 6 H 5 C 4 H 8 NH 3) 2 PbI 4 single crystals were synthesized by the slow cooling method, and their optical and scintillation properties were evaluated. Both samples had sharp X-ray diffraction peaks with intervals of (0 0 2 l) (l = 5–7). Absorption edges of (C 4 H 9 NH 3) 2 PbI 4 and (C 6 H 5 C 4 H 8 NH 3) 2 PbI 4 were confirmed at 535 and 520 nm, respectively. They showed luminescence due to the recombination of excitons at 500–700 nm. Scintillation decay times at 0.5–0.7 ns were obtained by approximation of decay curves. The light yields of (C 4 H 9 NH 3) 2 PbI 4 and (C 6 H 5 C 4 H 8 NH 3) 2 PbI 4 were respectively evaluated to be 1200 and 1500 photons/5.5 MeV-α by measuring full absorption peaks of 241Am α-rays. • (C 4 H 9 NH 3) 2 PbI 4 and (C 6 H 5 C 4 H 8 NH 3) 2 PbI 4 single crystals were grown by the slow cooling method. • Luminescence due to the recombination of free excitons was observed. • Scintillation decay times of sub-nanoseconds were observed. • Light yield of (C 6 H 5 C 4 H 8 NH 3) 2 PbI 4 was 1500 photons/5.5 MeV-α. [ABSTRACT FROM AUTHOR]

0.05, 0.1, 0.5, and 1.0 % Dy-doped YVO 4 single crystals were prepared by the optical floating zone technique to obtain photoluminescence (PL) and scintillation properties. All the samples showed the emission owing to charge transfer from V5+ ions to O2− ions inside [VO 4 ]3- and the 4f–4f transitions of Dy3+ ions. Light yields exhibited 37,000 (0.05 % Dy), 42,000 (0.1 % Dy), 44,000 (0.5 % Dy), and 39,000 photons/MeV (1.0 % Dy), based on the pulse height spectra. In afterglow properties, afterglow levels were 37.7 (0.05 % Dy), 25.7 (0.1 % Dy), 23.2 (0.5 % Dy), and 20.6 (1.0 % Dy) ppm. • We have synthesized Dy-doped YVO 4 single crystals by floating zone method. • We have characterized the photoluminescence, and scintillation properties of the Dy-doped YVO 4 single crystal. • Pulse height spectra revealed that the light yield of 0.05, 0.1, 0.5, and 1.0 % Dy-doped YVO 4 single crystals was 37,000, 42,000, 44,000, and 39,000 photons/MeV, respectively. • In afterglow properties, afterglow levels were 37.7 (0.05 % Dy), 25.7 (0.1 % Dy), 23.2 (0.5 % Dy), and 20.6 (1.0 % Dy) ppm. [ABSTRACT FROM AUTHOR]

• G2 glass matched with F2 glass (Schott) was used to draw fiber. • A linear increase and efficient response at 374 nm were obtained in G2 glass with X-ray radiation. • G2 glass material has an ideal and stable optical response. • G2 glass fiber has an emission at about 375 nm and a short fluorescence lifetime (2.22 ns). In order to enrich the application demands of neutron detection field, this study prepared a series of Ce3+/Gd3+ co-doped borosilicate scintillating glass materials. The ultraviolet (UV) absorption edges were all below 400 nm. The optical band gap was shortened from 3.48 eV to 3.24 eV as well as the optical basicity increased from 0.4941 to 0.5063 with the added concentration of Gd3+ ions. When the samples were excited by a 330 nm light source, the central wavelength of the emission spectra was 375 nm. The fluorescence lifetime of the sample was 30.99 ns. The emission intensity of the G2 sample increases linearly with the increase of X-ray excitation current, and has a stable optical response at 374 nm. The G2 glass fiber with the highest fluorescence intensity had a prominent emission peak at 375 nm and the fluorescence lifetime of 2.22 ns. [ABSTRACT FROM AUTHOR]

We fabricated BaCaBO 3 F (BCBF) with various Dy concentrations (0.1 %, 1 %, and 5 %), and evaluated the luminescence properties for radiation dosimetry. Sharp scintillation peaks originating from the 4f → 4f transition of Dy3+ were observed. Furthermore, thermally stimulated luminescence (TSL) glow curves were recorded, and a TSL glow peak at approximately 120 °C was observed. The 0.1 % Dy-doped BCBF exhibited the highest TSL intensity, and dose response curves of the 0.1–1 % Dy-doped BCBF were obtained in the 0.1–10000 mGy range. Moreover, at least seven activation energy levels related to TSL were confirmed by the TSL isothermal decay analysis. [ABSTRACT FROM AUTHOR]

Optical and scintillation properties of 50 AE O-50SiO 2 -1SnO (AE = Mg, Ca, Sr, Ba) glasses were investigated. In photoluminescence (PL) and scintillation, the glasses showed a luminescence peak around 400 nm which was attributed to the T 1 -S 0 transitions of Sn2+. The afterglow levels of the AE = Mg and Ba glasses were better than that of a commercial Tl-doped CsI scintillator. The light yields of the glasses were quantitatively acquired and the AE = Ba glass showed the highest light yield of 63 ph/5.5 MeV-α of among the glasses. [ABSTRACT FROM AUTHOR]

This work is dedicated to investigation of the luminescent properties of the prospective photoconversion material based on the crystal of Ce3+ doped Ca 3 Sc 2 Si 3 O 12 (CSSG) garnet. The GSSG:Ce crystal was grown using the micro-pulling-down (μPD) method. The CSSG:Ce crystal exhibited an intensive photoluminescence (PL) emission band with two sub-bands peaked at 504 and 545 nm, corresponding to 5d-4f (2F 5/2;7/2) transitions. Furthermore, we have investigated also the formation of cerium multicenters in the GSSG:Ce crystal using analyses of the structure of Ce3+ photoluminescence emission and excitation spectra under excitation of the luminescence of this crystal by synchrotron radiation. The formation of Ce3+-multicenters in CSSG:Ce garnet is caused by the local inhomogeneity of the dodecahedral sites of garnet lattice due to localization of the hetero-valent Sc3+ and Si4+ cations in the octahedral and tetrahedral positions of the garnet host. The existence of Ce3+ multicenters resulted in a significant enhancement of the Ce3+ emission band in the red range and improving the performance of conventional YAG:Ce phosphor. The next task of our work was to evaluate the possibility of application of the GSSG:Ce crystal as a light phosphor-converter (pc) for white light-emitting diodes (WLEDs). In the frame of this task, we have successfully developed a prototype of WLED by employing the CSSG:Ce crystal as a phosphor-converter (pc) with blue 450 emitting LED as well as investigated the color characteristics of this pc-WLED. • Ca 3 Sc 2 Si 3 O 12 :Ce (CSSG:Ce) crystal was grown by micropulling down method. • Presence of two different Ce1 and Ce2 emission centers was detected CSSG:Ce crystals. • Luminescent properties and energy structure of F+ and F centers in CSSG host were studied. • Prototypes of a white LED based on CSSG:Ce phosphor and blue LED were developed. [ABSTRACT FROM AUTHOR]

(C 6 H 5 C 2 H 4 NH 3) 2 Pb 1- x Ca x Br 4 (x = 0.05, 0.1, and 0.25) crystals were grown by the solvent diffusion method and evaluated for the photoluminescence and scintillation properties. When irradiated by X-rays, emission peaking at 440 nm due to exciton emission was observed. The pulse height spectra of (C 6 H 5 C 2 H 4 NH 3) 2 Pb 1- x Ca x Br 4 under 137Cs γ-ray irradiation demonstrate that the light yields were 20,000, 17,000, and 16,000 ph/MeV in x = 0.05, 0.1, and 0.25 samples, respectively. Ca-substitution significantly enhances the photoluminescence quantum yield and scintillation light yield. • (C 6 H 5 C 2 H 4 NH 3) 2 (Pb,Ca)Br 4 crystals were evaluated for the photoluminescence and scintillation properties. • (C 6 H 5 C 2 H 4 NH 3) 2 (Pb,Ca)Br 4 crystals exhibit a sharp emission peaking at 440 nm due to exciton luminescence. • Pulse height spectra under 137Cs γ-rays demonstrate the light yields was 20,000 ph/MeV. • Ca-substitution enhances both the photoluminescence and scintillation properties. [ABSTRACT FROM AUTHOR]

ZnO:Ga (GZO), as well as other band-edge luminous materials, exhibits fast time response properties, which makes it suitable for application as an ultraviolet scintillator for transient radiation detection. However, due to the serious self-absorption problem and low external quantum efficiency, the luminescence intensity cannot be intensified by increasing the volume of the crystals. To alleviate this problem, CsPbBr 3 quantum dot (QD) films were used to enhance the radioluminescence (RL) intensity of GZO. The effects of CsPbBr 3 QD films on the emission spectrum, intensity and angular distribution were experimentally analyzed under three different modes, namely, coating on the imaging surface, incident surface and both surfaces. The CsPbBr 3 QD film on the imaging surface could change the external quantum efficiency and luminescence angular distribution of GZO via its various surface morphologies. When CsPbBr 3 QD films were coated on both surfaces, the luminescence intensity reached 2.43 times that of GZO, while the proportion of emitted light from GZO was less than 6 %. Based on the experimental results, the principle of the enhancement and the difference among the three coating modes were discussed. The enhancement caused by CsPbBr 3 QD films on GZO was considerable and could be simply duplicated on many other materials, expanding their application in the field of detection and imaging. • Radioluminescence intensity of ZnO:Ga can be enhanced by coating perovskite films. • Scintillation performance of CsPbBr 3 QD film-coated ZnO:Ga was investigated. • Tuning the angular distribution by CsPbBr 3 QD film is beneficial for X-ray imaging. [ABSTRACT FROM AUTHOR]

Ce3+ activated high-density lanthanum lutetium germanate glass was fabricated by melt quenching method. Their densities, fluorescence decay curves, transmittance spectra, and luminescence excited by UV light and X-ray were measured and investigated. The densities of the glasses are between 5.90 g/cm3 and 5.97 g/cm3. The glasses present blue emission upon 379 nm light and X-ray. The blue emission lifetimes of the glasses are between 11.26 ns and 18.83 ns. The results shows that Ce3+ activated high-density lanthanum lutetium germanate glass would be a potential fast-event X-ray detection scintillating material. • Ce3+ doped germanate glasses with density around 6 g/cm3 were prepared. • The glass showed blue emissions upon UV light and X-ray. • The blue emission lifetimes were in the range of 11.26–18.83 ns. [ABSTRACT FROM AUTHOR]

Gd3+ and Ce3+ doped and co-doped NaCaYF 6 were synthesized noting the lack of luminescence studies in this material by using hydrothermal method. Synthesized NaCaYF 6 is also known by the mineral name Gagarinite. X-ray diffraction studies of prepared sample performed to confirm the identification of the phase pure fluoride compound. Energy dispersive spectra (EDS) and elemental mapping also recorded to confirm the compositions. Photoluminescence (PL) studies performed for recording PL Excitation (PLE) and PL Emission (PL) Spectra. Characteristic luminescence of Gd3+ ions and Ce3+ ions were observed in NaCaYF 6. The PLE of Ce3+ doped NaCaYF 6 phosphor shows broad excitation band centered at 294 nm with other weak shoulder peak at 272 nm. A typical double humped broad band emission obtained for the 294 nm excitation. Emission peak of 322 nm appears due to Ce3+ (5d–4f) transition with an additional shoulder peak at 315 nm. The PL spectra of the Gd3+-doped NaCaYF 6 excited at 272 nm consists of a dominant UVB emissions at 311 nm due to the transitions 6P 7/2 → 8S 7/2 of Gd3+ ions. No concentration quenching for Ce3+ was observed while luminescence of Gd3+activator got quenched at 1 mol %. The peculiarity of Gd3+ emission was the long lifetime of the order of 10 ms. Luminescence characteristics are explained using the known energy level diagrams for the lanthanide activators. The results revealed that Gd3+ and Ce3+ doped NaCaYF 6 compound could find a promising application for the UV-emitting phototherapy lamps. [Display omitted] • Novel results on observation of UV emission in NaCaYF 6 :Ln3+ (Ln3+ = Ce, Gd) materials are reported for the first time. • The samples of pristine and Ln3+ doped NaCaYF 6 have been prepared by the Hydrothermal method. • Characteristic line emission for Ce and Gd doped NaCaYF 6 are observed. • This can be useful in various UV applications. [ABSTRACT FROM AUTHOR]

High-quality lutetium aluminum garnet doped with various Pr3+ concentrations ((Lu 1- x Pr x) 3 Al 5 O 12 , abbreviated to Pr:LuAG) single crystals were grown by the optical floating zone method. The concentration of Pr3+ dependence on microstructure, luminescence and scintillation properties were systematically studied. Based on the results of Rietveld refinement, the doping of Pr3+ leads to lattice distortion and lowers its symmetry. The symmetry of the LuO 8 dodecahedron center is lowest at 0.010, as confirmed by the Raman spectra. When excited at 450 nm and X-rays, the primary emission peak at 614 and 300 nm, respectively, induced by Pr3+ 4 f 2-4 f 2 and 4 f 5 d -4 f 2 transitions. The optimal doping concentration is 0.010. The electric dipole-electric dipole interaction between adjacent Pr3+ was responsible for the concentration quenching in the Pr:LuAG single crystals. (Lu 0.990 Pr 0.010) 3 Al 5 O 12 shows the shortest average scintillation decay time (22.55 ns) and highest light yield (23,842 ± 2300 ph./MeV) under 662 KeV 137Cs gamma-ray irradiation. In terms of overall luminescence and scintillation performance, 0.010 doping was the best for Pr3+ doped LuAG single crystals. • High quality Pr:LuAG single crystal was grown by optical floating zone method. • Pr ions lead to the enhanced translational motion of rare earth ions in Pr:LuAG. • Electric dipole-electric dipole interaction induced concentration quenching of Pr3+. • 0.010 Pr:LuAG single crystal has the best scintillation and luminescence properties. [ABSTRACT FROM AUTHOR]

Hexagonal-structure Mg 4 Ta 2 O 9 (MTO) powders doped by 0.25 at% RE (RE = La3+, Ce3+, Pr3+, Nd3+, Sm3+, Eu3+, Gd3+, Tb3+, Dy3+, Ho3+, Er3+, Tm3 +, Yb3+, Lu3+, Y3+, Sc3+) were synthesized. All the rare earth-doped samples were checked by X-ray diffraction (XRD) and confirmed to be monophasic powders. Among them, Mg 4 Ta 2 O 9 doped by 0.25 at% Gd3+ and Sc3+ had higher X-ray excited luminescence (XEL) emission peak intensities, 3.05 and 2.79 times of MTO, respectively. The optimal concentrations of Gd3+ and Sc3+ were investigated based on XEL main emission peak intensity changing with the amount of dopants in the range of 0∼1.0 at%. The optimal XEL emission peak intensities were measured 3.32 and 3.09 times of MTO for MTO: 0.8 at% Gd3+ and MTO: 0.4 at% Sc3+, respectively. The photoluminescence (PL) emission peaks at around 370 nm correspond to two excitation peaks at 158 and 215 nm. The excitation peak at 158 nm is about 10 times more than that of at 215 nm in intensity. The emission spectra excited by vacuum ultraviolet light at 158 nm and ultraviolet light at 215 nm were investigated associated with scintillation emission mechanism. MTO: 0.8 at% Gd3+ and MTO: 0.4 at% Sc3+ show potential application in security inspection, industrial detection, etc. • Single-phase Mg 4 Ta 2 O 9 : 0.25 at% RE (RE = La3+, Ce3+, Pr3+, Nd3+, Sm3+, Eu3+, Gd3+, Tb3+, Dy3+, Ho3+, Er3+, Tm3 +, Yb3+, Lu3+, Y3+, Sc3+) samples were synthesized. • Single-phase Mg 4 Ta 2 O 9 : x at% M (x = 0, 0.2, 0.4, 0.6, 0.8, 1.0; M = Gd3+, Sc3+) samples were synthesized. • MTO: 0.8 at% Gd3+ among MTO: x at% Gd3+ and MTO: 0.4 at% Sc3+ among MTO: x at% Sc3+ have the highest excitation peaks at 158 and 215 nm. • MTO: 0.8 at% Gd3+ and MTO: 0.4 at% Sc3+ have highest relative main XEL emission peak intensities of 3.27 and 3.09 times of MTO, respectively. • The scintillation emission mechanism of improving XEL properties of Mg 4 Ta 2 O 9 scintillators by rare-earth doping is thoroughly analyzed. [ABSTRACT FROM AUTHOR]

Crystalline ceramic material (Gd,Y) 3 Al 2 Ga 3 O 12 codoped with Ce and Tb (GYAGG: Ce, Tb) was demonstrated to be a high light yield scintillator. The luminescence kinetics was proven to be formed by the combining of the direct Tb3+→Ce3+ and inverse Ce3+→Tb3+ transfer of electronic excitations. This forms a mechanism leading to the increase of the slow component fraction in the scintillation and limits the application of the material, when a fast response is required. However, a high light yield opens an opportunity to utilize the developed material for application in the detectors operating in a current measurement mode and, in long living, as high-flux sources of optical photons under the ionizing radiation of a different type. • (Gd,Y) 3 Al 2 Ga 3 O 12 : Ce, Tb is high light yield scintillator. • Both direct Tb3+→Ce3+ and inverse Ce3+→Tb3+ transfers form luminescence kinetics. • Prospective material for a high-flux of optical photons under the ionizing radiation. [ABSTRACT FROM AUTHOR]

Four phenanthroimidazole-functionalized coumarins (C-PI-Bu , C-PI-CN, C-PI-TRZ, and C-PI-Cz) containing a 7-diethylaminocoumarin unit and a phenanthroimidazole (PI) unit with different phenyl substituent at the N 1-position, were successfully synthesized and characterized by NMR (1H and 13C), high-resolution mass spectrometry and elemental analysis. The structure-property relationships of the compounds were revealed by systematically investigating their thermal stability, photophysical and electrochemical properties. All four compounds exhibit bright blue-green emission with high fluorescence quantum yield (75.36 %–97.00 %) in dichloromethane solution and green emission in the solid-state. The organic light-emitting diodes (OLEDs) with a device of ITO/PEDOT:PSS (30 nm)/TBADN:coumarin derivative (x, wt%) (25 nm)/TPBi (35 nm)/Liq (2 nm)/Al (150 nm) were fabricated and characterized. The above OLEDs showed the best EL performances with a maximum brightness (L max) of 8500 cd/m2, a maximum current efficiency (CE max) of 3.45 cd/A, and a maximum external quantum efficiency (EQE max) of 1.30 %. [Display omitted] • Four phenanthroimidazole-functionalized coumarins were synthesized for OLEDs. • The phenanthroimidazole-functionalized coumarins exhibited strong emission in solution and in solid-state. • Devices containing the cyanophenyl substituted compound showed L max of 8500 cd/m2, CE max of 3.45 cd/A, and EQE max of 1.30 %. [ABSTRACT FROM AUTHOR]

(K,Rb) 2 CuBr 3 crystals were fabricated by the slow cooling method, and their photoluminescence (PL) and scintillation properties were examined. Emission bands were observed at 350–550 nm under UV and X-ray irradiation. PL quantum yields of K 2 CuBr 3 , (K 0.25 ,Rb 0.75) 2 CuBr 3 , (K 0.5 ,Rb 0.5) 2 CuBr 3 , (K 0.75 ,Rb 0.25) 2 CuBr 3 , and Rb 2 CuBr 3 were respectively 75.8, 71.0, 82.3, 96.9, and 96.3%. The scintillation decay curves were approximated by a sum of three exponential functions, and the decay time constants due to recombination of self-trapped excitons were 58–63 μs. The afterglow levels of the K and Rb-mixed samples at 20 ms passed after X-ray irradiation decreased to 10–40 ppm, compared with those of K 2 CuBr 3 and Rb 2 CuBr 3. Among these samples, (K 0.75 , Rb 0.25) 2 CuBr 3 showed the highest light yield of 7400 ph/MeV among the samples calculated from the pulse height spectra of 137Cs γ-rays (662 keV). • (K,Rb) 2 CuBr 3 crystals were synthesized by the slow cooling method. • The afterglow levels of the (K,Rb) 2 CuBr 3 were 10–40 ppm. • (K 0.75 ,Rb 0.25) 2 CuBr 3 showed the highest light yield (7400 ph/MeV) in prepared samples. [ABSTRACT FROM AUTHOR]

The HERMES (High Energy Rapid Modular Ensemble of Satellites) Pathfinder mission aims to develop a constellation of nanosatellites to study astronomical transient sources, such as gamma-ray bursts, in the X and soft γ energy range, exploiting a novel inorganic scintillator. This study presents the results obtained describing, with an empirical model, the unusually intense and long-lasting residual emission of the GAGG:Ce scintillating crystal after irradiating it with high energy protons (70 MeV) and ultraviolet light (∼ 300 nm). From the model so derived, the consequences of this residual luminescence for the detector performance in operational conditions has been analysed. The suitability of this detector for the HERMES Pathfinder nanosatellites was demonstrated by the low contribution of the afterglow, 1–2 pA at peak, to the input current of the front-end electronics. [ABSTRACT FROM AUTHOR]

Luminescence and scintillation properties of Lu 2 YAl 2.5 Ga 2.5 O 12 :Ce,Mg (0.02, 0.05 %) garnet crystals grown by the micro-pulling down method were investigated. The onset temperature for luminescence quenching at ∼365 K is determined from the temperature dependence of photoluminescence decay time. At room temperature, the Mg (0.05 %) sample exhibits high integral scintillation efficiency of ∼445 % of BGO crystal, light yield value of 23,500 photons/MeV, and fast scintillation decay times of 20 ns (15 %) + 54 ns (85 %). The higher radioluminescence intensity of the Mg (0.05 %) sample correlates with an appearance of its lower themally-stimulated luminescence intensity in 77–500 K range. • Luminescence and scintillation properties of Lu 2 YAl 2.5 Ga 2.5 O 12 :Ce,Mg (Mg = 0.02 %, 0.05 %) crystals are investigated. • Both crystals show onset of luminescence quenching at 365 K. • Lu 2 YAl 2.5 Ga 2.5 O 12 :Ce,0.05%Mg shows light yield of 23,500 photons/MeV. • Lu 2 YAl 2.5 Ga 2.5 O 12 :Ce,0.05%Mg shows scintillation decay time of 20 ns (14 %) + 54 ns (86 %). • Thermoluminescence characteristics are investigated. [ABSTRACT FROM AUTHOR]

Novel Sm3+ activated oxyfluoride glass was synthesized via the melt-quenching approach with subsequent heat treatment. The X-ray diffraction measurement discloses the amorphous nature of prepared glasses. And, FTIR illustrates the molar surplus of Bi 2 O 3 raises the network connectivity by creating bridging oxygen sites in the structure. The Judd-Ofelt (J-O) intensity parameters exhibit Ω 4 >Ω 2 >Ω 6 trend, witnessing the rigidity of the glass structure and ionic bonding between Sm3+ ions and surrounding ligands. The 4G 5/2 → 6H 7/2 transition of Sm3+ is the most applicable for reddish-orange lasers due to their higher values of radiative transition probability, branching ratio, and stimulated emission cross-section. The optimum emission intensity is obtained with 30 mol% Bi 2 O 3 and the corresponding decay time is 1.40 ms. Additionally, the F30 glass sample was lit in a reddish-orange region having a CCT value of 1689 K. The thermal luminescence quenching of the prepared glass was studied and the thermal stability parameters activation energy was estimated. Further, the contactless optical thermometry capability of the glass sample was explored within the range of 303 K–603 K using the luminescence intensity ratio (LIR) technique. Thus, the above studies on the glass sample suggest that it can be used as an active medium in lasers, contactless optical temperature sensing, and high-energy scintillator applications. [Display omitted] • Spectroscopic and structural characteristics of NaF– B 2 O 3 – Bi 2 O 3 –Sm 2 O 3 are explored. • These oxyfluoride glasses shows more rigidity with Ω 4 >Ω 2 >Ω 6 trend. • The reddish-orange emission is originated from 4G 5/2 → 6H 7/2 transition. • The optimum emission intensity has been observed with the 30 mol% doping of Bi 2 O 3. [ABSTRACT FROM AUTHOR]

X-ray luminescent diamond composite films with embedded yttrium-aluminum nanoparticles were designed. Additionally, the stability limits of single-phase solid solutions in systems based on yttrium-aluminum and yttrium-scandium-aluminum garnets doped with cerium were determined. The most intense X-ray luminescence was achieved with the [Y 2·98 Ce 0.02 ]{Al 2 }Al 3 O 12 powder. The composition-optimized nanoparticles were embedded into a polycrystalline diamond matrix to form a diamond-YAG:Ce composite. For the obtained composite, an intense X-ray luminescence from the Ce3+ ions near 550 nm was demonstrated. The designed composites may be used as adjustable and durable scintillating materials for a wide range of applications. [ABSTRACT FROM AUTHOR]

• Regularities of Bi 4 Ge 3 O 12 formation in hydrothermal-microwave conditions are studied. • Additives allow to reduce temperature and duration of synthesis. • Chelating agents are more effective to modify the particle shape than surfactants. • Reducing particle size helped improve scintillation properties of the material. A route for production of fine Bi 4 Ge 3 O 12 (BGO) powder is sought after to lower the cost of scintillation devices and make their shapes more versatile. A systematic study of highly dispersed BGO crystallization under the hydrothermal-microwave (HTMW) conditions was carried out in the present work. Anionic, cationic and non-ionic surfactants, chelating agents and polyols were used to modify the synthesis and their respective effects on phase composition and morphology were determined. It was shown that chelating agents or other additives that are capable of forming complexes with the bismuth ions allow the production of smaller, non-aggregated particles and have the procedure be scaleable. BGO powders of various morphology were synthesized and study of the optical properties of the product discovered their advantages over traditional single-crystal material. The BGO powders obtained in optimal HTMW conditions are characterized by the presence of a single intense fast scintillation component with a flash time of about 11 ns which is by an order of magnitude less than that observed in single-crystal BGO (327 ns). This suggests the suitability of these powders for the production of scintillation materials with improved properties. This material is promising for creating highly sensitive composite detectors with a high rate of counting events. [ABSTRACT FROM AUTHOR]

This study concerns cerium and boron doped Lu 3 Al 4 Sc 1 O 12 and Gd 3 Al 3 Sc 2 O 12 garnet µ-crystalline powders, which were synthesized for the first time. Rare earth ion, particularly Ce3+ activated garnets, due to their high density and efficient Ce3+ luminescence upon blue, UV, or x-ray excitation, can be used as scintillators that convert high-energy radiation into visible light. The incorporation of B3+ and Sc3+ ions into the garnet matrix corresponds to the improvement of the scintillating properties. Boron in these compounds could act like a flux and thus modulate particle morphology, while scandium solely changes the physical and luminescent properties of these garnets. From the measured radioluminescence emission spectra, it could be concluded that boron doping results in a higher emission intensity when the compounds are excited by high-energy radiation. The most striking effect is that the decay time is reduced, and the quantum efficiency of the compounds increases. After improving the kinetic properties of these compounds, it is possible to discuss a wider application of the synthesized materials. In addition to the aforementioned properties, room temperature as well as temperature dependent photoluminescence emission, excitation, and decay times at different temperatures were taken for all samples. The elemental composition of the samples was determined by using the ICP-OES technique. The crystal structure was analyzed by means of powder XRD. Particle morphology and size distribution were also investigated. The main idea of this research is to synthesize new and adjusted garnet type compounds that show better luminescent properties, which are required for scintillator materials. • Pure B3+ and Sc3+ co-doped LuAG:Ce and GdAG:Ce were synthesized by Sol-Gel method. • Reflectance spectra indicated about good quality of synthesized compounds. • Boron doping led to an increase in radio/photo luminescence intensities. • A reduction in decay times was caused by B3+ and Sc3+ co-doping. • Co-doping with B3+ led to an increase in quantum efficiency. [ABSTRACT FROM AUTHOR]

The glass samples were prepared by melt quenching method and changing Eu 2 O 3 concentrations following component of xEu 2 O 3 - 40Na 2 O - 7.5Gd 2 O 3 - 5SiO 2 - (47.5-x)B 2 O 3 (x = 0, 1, 2, 3 mol %). Density and molar volume tend to increase with increasing Eu 2 O 3 concentrations, corresponding to the larger non-bridging oxygen. Fourier transform infrared spectra (FTIR) results point out that the majority BO 3 borate group. The absorption spectra were represented in the length of UV-Vis and NIR region. The phonon energy of 3Eu:7.5Gd was 1280.54 cm−1, related to the borate glass host. The photoluminescence and X-ray-induced luminescence spectra of 3Eu:7.5Gd glass showed similar highest intensity at 613 nm (5D 0 →7F 2). The photoluminescence quantum yield (PLQY) of 3Eu:7.5Gd glass shows the highest value at 85.70 %. The scintillation efficiency of 3Eu:7.5Gd glass was 17.51 % of bismuth germanate (BGO) crystal. The decay time owing to Eu3+ emission is 2.054 ms for 2Eu:7.5Gd glass. The highest energy transfer efficiency was 2 mol % of Eu 2 O 3 concentrations (η ET = 70 %). The CIE chromaticity coordinates of the glasses are placed in the reddish-orange area (0.65, 0.35). The spatial resolution of X-ray imaging study was 10 lp/mm. These results suggest that 3 mol % of Eu 2 O 3 doped silicoborate glass is capable of being a scintillator applied in the X-ray imaging system. [ABSTRACT FROM AUTHOR]

BaCl 2 :Eu transparent ceramics were synthesized by the spark plasma sintering method, and concentration dependence of Eu on optical and scintillation properties was investigated. BaCl 2 :Eu transparent ceramics showed photoluminescence (PL) and scintillation peaks at 400 nm due to 5d–4f transition of Eu2+. The PL and scintillation decay time constants of BaCl 2 :Eu transparent ceramics were ∼400 ns. The PL quantum yields (QY s) of 0.05, 0.1, 0.5, and 1% BaCl 2 :Eu transparent ceramics were 28.5, 25.6, 16.2, and 13.9%, respectively. The afterglow levels of BaCl 2 :Eu transparent ceramics were lower than CsI:Tl single crystal in practical use. The scintillation light yield of the 0.5% doped BaCl 2 :Eu transparent ceramic was 9800 photons/MeV when γ-rays by 137Cs were irradiated. • BaCl 2 :Eu transparent ceramics were synthesized using the SPS method. • We investigated the optical and scintillation properties. • The scintillation peak due to 5d–4f transition of Eu2+ was observed at 400 nm. • The 0.5% Eu-doped sample showed the highest LY (9800 ph/MeV) under 137Cs γ-ray irradiation. [ABSTRACT FROM AUTHOR]

To develop glass scintillators, Eu 2 O 3 -doped tellurite glasses (TeO 2 –Nb 2 O 5 –SrO–Eu 2 O 3) (TNbSrEu) were prepared, and their luminescence characteristics were investigated. Several photoluminescence peaks at about 578, 592, 613, 652, and 701 nm were observed when excited by 530 nm excitation light. They originated from 4f→4f transition of Eu3+. Their photoluminescence decay times under 530 nm excitation light were approximately 0.7 ms, which was a typical time of 4f→4f transition of Eu3+. Further, some scintillation peaks originating from 4f→4f transition of Eu3+ were detected at 577, 593, 613, and 652 nm, and scintillation decay times were in the time region of 0.21–0.35 ms. Furthermore, the afterglow levels were from 560 ppm to 317 ppm, showing a decreasing trend in levels with increasing Eu 2 O 3 concentration. • To develop glass scintillators, Eu 2 O 3 -doped tellurite glasses (TeO 2 –Nb 2 O 5 –SrO–Eu 2 O 3) were prepared. • Some scintillation peaks originating from 4f.→4f transition of Eu3+ were detected. • The tellurite glasses showed a decreasing trend in afterglow levels with increasing Eu 2 O 3 concentration. [ABSTRACT FROM AUTHOR]