Search

With a growing population of about 7.8 billion, humans are generating tons of waste in the form of non-biodegradable plastics on a daily basis that ends up in landfills and oceans. The introduction of packaging has been a blessing to mankind by facilitating the ease of convenience in transportation, delivery and general usage. The downside, however, is that majority of the packaging currently available is harmful to the environment and takes thousands of years to decay. This paper discusses the use of chitosan from shrimp shells and other marine animals' exoskeleton waste in food packaging industries. Chitosan extracted from marine organisms is modulated in the form of packaging material. Compared to conventional packaging, chitosan films are 73.4% biodegradable in soil under laboratory conditions whereas 100% degraded in an open field. Chitosan with metal oxides, essential oils, natural extracts, proteins and other polymers show enhanced tensile strength, water vapor permeability, oxygen and ultraviolet barrier. Chitosan and composite film show antimicrobial activity against gram positive and negative bacteria. Comparative approaches on environmental impacts between conventional plastics and chitosan films are enlightened, thereby highlighting the importance of natural polymers as packaging films that are considered economic based on the addition of additives. [ABSTRACT FROM AUTHOR]

To improve the shortcomings of poly (3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), such as brittleness, large grain size and high crystallinity, a kind of bio-based engineering polyester elastomer (BEPE) was incorporated into PHBV by melting blending method with benzoyl peroxide (BPO) as the initiator. With the addition of BPO, the interfacial adhesion between PHBV and BEPE was improved, and BPO hindered the crystallization and reduced the crystallinity of PHBV/BEPE blends. At the same time, the gel content, the dynamic complex viscosity and dynamic elastic modulus of blends were increased significantly in low-frequency region with 0.7-phr BPO. Compared to that of neat PHBV, the elongation at break and impact strength of PHBV/BEPE/BPO (0.7 phr) blends were increased by 373.6 and 158.7%, respectively. Compared to that of PHBV/BEPE blends, the elongation at break and impact strength of the PHBV/BEPE/BPO (0.7 phr) blends were increased by 44.3 and 122.7%, respectively. The above phenomena were resulted from the formation of chemical micro-crosslinking between PHBV and BEPE. The main mechanism can be explained, PHBV and BEPE polymer radicals were generated by BPO initiator, and then, PHBV and BEPE polymer radicals recombined to form carbon–carbon crosslinking. [ABSTRACT FROM AUTHOR]

In this study we prepared a poly(lactic acid)/ethyl cellulose (PLA/EC) bioplastic blend film by melt pressing after solvent casting and investigated the optical, thermal, and mechanical properties in relation to the structural changes revealed by various microscopies and scattering measurements. Despite the immiscibility of PLA and EC, the blend film exhibited good optical transparency due to the close match in their refractive indices. A second run of differential scanning calorimetry during heating revealed a decrease in the glass transition temperature ( T g PLA ) and melting point ( T m PLA ) of PLA with EC although EC had the higher values. Thermomechanical analysis suggested that these decreases were due to the negative pressure generated due to the suppression of PLA shrinkage below T g EC and above T g PLA during cooling. Furthermore, ductile drawing of the blend film (70/30) at an optimal temperature of 70 °C above T g PLA resulted in a uniform whitening near 100% strain. Delamination at the interface between the PLA matrix and EC domain led to the formation of micrometer-sized oriented voids, which enhanced the refractive index difference in the phase-separated structure, thereby scattering light and achieving the uniform and oriented white blend film. [ABSTRACT FROM AUTHOR]

Microplastics are micrometre-sized emerging pollutants produced by plastic fragmentation. They have been recently detected in most ecosystems, even in remote areas. Here, we review microplastics with emphasis on sources, occurrence, transport, detection methods, policies, toxicity, and management methods. In the transport section, we discuss sorption kinetics, layered microplastics, and influencing factors such as biofilm formation. Microplastic management can be done by adsorption, filtration, oxidation, and biodegradation. Microplastic interaction is influenced by temperature, pH, salinity, and dissolved organic matter. [ABSTRACT FROM AUTHOR]

Plastic pollution is becoming a major health issue due to the recent discovery of microplastics and nanoplastics in living organisms and the environment, calling for advanced technologies to remove plastic waste. Here we review enzymes that degrade plastics with focus on plastic properties, protein engineering and polymers such as poly(ethylene terephthalate), poly(butylene adipate-co-terephthalate), poly(lactic acid), polyamide and polyurethane. The mechanism of action of natural and engineered enzymes has been probed by experimental and computation approaches. The performance of polyester-degrading enzymes has been improved via directed evolution, structure-guided rational design and machine learning-aided strategies. The improved enzymes display higher stability at elevated temperatures, and tailored substrate-binding sites. [ABSTRACT FROM AUTHOR]

The global plastic production has steadily increased from 1.7 million tons in 1950 to over 400 million tons in 2022, with about 60% of plastic ultimately ending up in landfills and oceans. There is also growing evidence that microplastics exert negative effects on biota and ecosystems. Biodegradable plastics may represent a safe alternative, yet their potential adverse effects have not been comprehensively analyzed. Here, we reviewed biodegradable plastics, with focus on their conversion into microplastics, their interactions with pollutants, and their combined toxicity for aquatic biota. Biodegradable plastics include polylactic acid, polyhydroxyalkanoates, polybutylene succinate, poly(butylene adipate-co-terephthalate), and poly(ε-caprolactone). We found that some biobased plastics are hardly biodegradable. Some biobased plastics are compostable but require specific environmental conditions for their biodegradation. Biobased plastics can generate microplastics when released into the environment, which can impact biota. Contrary to the common public belief, biodegradable plastics may not only originate from biosources but can be synthesized from fossil fuels. Microplastics originating from biodegradable plastics can interact with pollutants, adsorbing and transporting these pollutants, resulting in synergistic or antagonistic effects on exposed organisms. Biofilm formation on microplastics impacts their degradation and pollutant interactions. [ABSTRACT FROM AUTHOR]

Rationale: Plastic mulch film manages weed growth and moisture loss on the surface of cropping beds. The chemical components of such plastics include polymer(s), additives and non‐intentionally added substances (NIASs). The unknown chemical nature and behaviours of these constituents require investigation due to their potential to add to the anthropogenic chemical burden in the agrifood system. Methods: Solvent extracts of a commercial 15% polylactic acid (PLA)/85% poly(butylene adipate‐co‐terephthalate) mulch film were investigated using gas chromatography–mass spectrometry (GC–MS) with electron ionisation to characterise the additive and NIAS components. The obscurity of some of the NIASs meant their identification was not readily achieved through routine MS library comparisons. As such, the identification of several polymer‐derived compounds required interpretation of the MS data and re‐application of the derived fragmentation patterns with reference to the wider literature. Unknowns were confirmed using commercially available compounds. Results: Unknown NIASs were identified as cyclic oligoesters comprised of the monomeric building blocks of the polymer system. Cyclic structures derived from the monomers of polybutylene adipate (PBA) and polybutylene terephthalate (PBT) fragmented through a primary pathway involving 1,5‐ and 1,3‐H transfers at ester linkages. Characteristic ions at m/z 111, 129, 183 and 201 for PBA‐derived cyclic oligoesters and m/z 104, 132, 149 and 221 for PBT‐derived cyclic oligoesters were assigned in the mass spectra of unknowns. Cyclic oligoesters containing sebacate moieties were also identified, indicating the presence of polybutylene sebacate as an unexpected component of the mulch. Conclusions: Systematic analyses of the sort reported here are valuable for providing alternative approaches for the identification of plastic‐related chemicals. Open publication of MS spectral data is required to build a greater understanding of the mulch film chemical components contributing to the environmental chemical load introduced to agroecosystems. [ABSTRACT FROM AUTHOR]

Detecting, separating, and characterizing airborne microplastics from other airborne particulates is currently challenging due to the various instrumental constraints and related sample preparation hurdles that must be overcome. The ability to measure these real-world environments is needed to better assess the risks associated with microplastics. To that end, the current study focused on developing a methodology for sampling and characterizing airborne microplastics. Particulate sampling was carried out at a municipal materials recovery facility near a conveyer belt containing sorted plastic materials to collect airborne environmental particles on filters. Nucleopore filters were mounted on Teflon support rings, coated with 100 nm aluminum to reduce the background signal for micro-Raman spectroscopy, and marked with a fiducial pattern using a laser engraver. The fiducial pattern was crucial in identifying samples, relocating particles, and efficiently enabling orthogonal measurements on the same samples. Optimum sampling conditions of 2 h at 25 L/min were determined using light microscopy to evaluate the particle loadings. The filters were then cut into slices which were attached to sections of thin beryllium-copper sheeting for easy transfer of the filter between microscopy platforms. Scanning electron microscopy was used to identify carbon-rich particles. Light microscopy was used to identify colored particles which were also carbon-rich which were then analyzed using micro-Raman spectroscopy to identify specific polymers. [ABSTRACT FROM AUTHOR]

Soil conservation is one of the best methods to improve soil fertility and enhance crop growth efficiency. Replacing plastic mulch with biomass is an environmentally friendly strategy. Innovative encapsulated soil granules (ESGs) were developed using PVA/PC film as the wall material and rural soil as the core. The PVA/PC was synthesized using 60% protein polypeptide (PC) from leather waste scrap and 35% poly (vinyl alcohol) (PVA), which was optimized for water absorption expansion and water retention performance. The ESG-10 granulated with 10% PVA/PC exhibited good water absorption, moisture retention, and resistance to water solubility. As an auxiliary material for soil improvement, the amount of ESGs mixed with the topsoil at ratios of 0 g/m2, 200 g/m2, and 400 g/m2 was proportional to the soil insulation and moisture retention. In rapeseed cultivation, the experimental results indicated that the soil mulched with ESG-10 can maintain seedling vitality for a long time under low water content conditions. [ABSTRACT FROM AUTHOR]

Approximately 50% of global plastic wastes are produced from plastic packaging, a substantial amount of which is disposed of within a few minutes of its use. Although many plastic types are designed for single use, they are not always disposable. It is now widely acknowledged that the production and disposal of plastics have led to a plethora of negative consequences, including the contamination of both groundwater and soil resources and the deterioration of human health. The undeniable impact of excessive plastic manufacturing and waste generation on the global plastic pollution crisis has been well documented. Therefore, degradable polymers are a crucial solution to the problem of the non-degradation of plastic wastes. The disadvantage of degradable polymers is their high cost, so blending them with natural polymers will reduce the cost of final products and maximize their degradation rate, making degradable polymers competitive with industrial polymers that are currently in use daily. In this work, we will delineate various degradable polymers, including polycaprolactone, starch, and cellulose. Furthermore, we will elucidate several aspects of polyvinyl alcohol (PVA) and its blends with natural polymers to show the effects of adding natural polymers on PVA properties. This paper will study cost-effective and ecologically acceptable polymers by combining inexpensive natural polymers with readily accessible biodegradable polymers such as polyvinyl alcohol (PVA). [ABSTRACT FROM AUTHOR]

The synthesis of conventional plastics has increased tremendously in the last decades due to rapid industrialization, population growth, and advancement in the use of modern technologies. However, overuse of these fossil fuel-based plastics has resulted in serious environmental and health hazards by causing pollution, global warming, etc. Therefore, the use of microalgae as a feedstock is a promising, green, and sustainable approach for the production of biobased plastics. Various biopolymers, such as polyhydroxybutyrate, polyurethane, polylactic acid, cellulose-based polymers, starch-based polymers, and protein-based polymers, can be produced from different strains of microalgae under varying culture conditions. Different techniques, including genetic engineering, metabolic engineering, the use of photobioreactors, response surface methodology, and artificial intelligence, are used to alter and improve microalgae stocks for the commercial synthesis of bioplastics at lower costs. In comparison to conventional plastics, these biobased plastics are biodegradable, biocompatible, recyclable, non-toxic, eco-friendly, and sustainable, with robust mechanical and thermoplastic properties. In addition, the bioplastics are suitable for a plethora of applications in the agriculture, construction, healthcare, electrical and electronics, and packaging industries. Thus, this review focuses on techniques for the production of biopolymers and bioplastics from microalgae. In addition, it discusses innovative and efficient strategies for large-scale bioplastic production while also providing insights into the life cycle assessment, end-of-life, and applications of bioplastics. Furthermore, some challenges affecting industrial scale bioplastics production and recommendations for future research are provided. [ABSTRACT FROM AUTHOR]

Synthetic polymers, commonly known as plastics, are currently present in all aspects of our lives. Although they are useful, they present the problem of what to do with them after their lifespan. There are currently mechanical and chemical methods to treat plastics, but these are methods that, among other disadvantages, can be expensive in terms of energy or produce polluting gases. A more environmentally friendly alternative is recycling, although this practice is not widespread. Based on the practice of the so-called circular economy, many studies are focused on the biodegradation of these polymers by enzymes. Using enzymes is a harmless method that can also generate substances with high added value. Novel and enhanced plastic-degrading enzymes have been obtained by modifying the amino acid sequence of existing ones, especially on their active site, using a wide variety of genetic approaches. Currently, many studies focus on the common aim of achieving strains with greater hydrolytic activity toward a different range of plastic polymers. Although in most cases the depolymerization rate is improved, more research is required to develop effective biodegradation strategies for plastic recycling or upcycling. This review focuses on a compilation and discussion of the most important research outcomes carried out on microbial biotechnology to degrade and recycle plastics. [ABSTRACT FROM AUTHOR]

α-zeins are amphiphilic maize seed storage proteins with material properties suitable for a multitude of applications e.g., in renewable plastics, foods, therapeutics and additive manufacturing (3D-printing). To exploit their full potential, molecular-level insights are essential. The difficulties in experimental atomic-resolution characterization of α-zeins have resulted in a diversity of published molecular models. However, deep-learning α-zein models are largely unexplored. Therefore, this work studies an AlphaFold2 (AF2) model of a highly expressed α-zein using molecular dynamics (MD) simulations. The sequence of the α-zein cZ19C2 gave a loosely packed AF2 model with 7 α-helical segments connected by turns/loops. Compact tertiary structure was limited to a C-terminal bundle of three α-helices, each showing notable agreement with a published consensus sequence. Aiming to chart possible α-zein conformations in practically relevant solvents, rather than the native solid-state, the AF2 model was subjected to MD simulations in water/ethanol mixtures with varying ethanol concentrations. Despite giving structurally diverse endpoints, the simulations showed several patterns: In water and low ethanol concentrations, the model rapidly formed compact globular structures, largely preserving the C-terminal bundle. At ≥ 50 mol% ethanol, extended conformations prevailed, consistent with previous SAXS studies. Tertiary structure was partially stabilized in water and low ethanol concentrations, but was disrupted in ≥ 50 mol% ethanol. Aggregated results indicated minor increases in helicity with ethanol concentration. β-sheet content was consistently low (∼1%) across all conditions. Beyond structural dynamics, the rapid formation of branched α-zein aggregates in aqueous environments was highlighted. Furthermore, aqueous simulations revealed favorable interactions between the protein and the crosslinking agent glycidyl methacrylate (GMA). The proximity of GMA epoxide carbons and side chain hydroxyl oxygens simultaneously suggested accessible reactive sites in compact α-zein conformations and pre-reaction geometries for methacrylation. The findings may assist in expanding the applications of these technologically significant proteins, e.g., by guiding chemical modifications. [ABSTRACT FROM AUTHOR]

This study presents a novel hydrophobic lignocellulosic bioplastic from corn stover reinforced by oxidized cellulose and in situ regenerated lignin. Cellulose‐lignin mixture as a matrix was obtained by acid‐recyclable deep eutectic solvent (DES) pretreatment of corn stover in mild conditions. Triethoxy(octyl)silane (C14H32O3Si) was employed to improve the water stability of the bioplastic by vapor deposition. The results show that the hydrophobic bioplastic has a high tensile strength, measuring 62.36 MPa. The water contact angle of the bioplastic was increased from 8.50° to 121.9° after hydrophobic modification. We prepared oxidized cellulose‐reinforced cellulose paper by different particle size distributions of oxidized cellulose to investigate the reinforcement of oxidized cellulose. The tensile strength of oxidized cellulose cellulose paper increased from 14.41 to 21.18 MPa with the addition of oxidized cellulose. The zeta potential of oxidized cellulose is −47.99 mV, which shows a more negative charge due to carbonyl groups. The repulsive force of oxidized cellulose contributes to the formation of a brick‐and‐mortar microstructure with cellulose‐lignin mixture. It demonstrates that oxidized cellulose can act as bio‐adhesives and has a good toughening effect on the mechanical properties of bioplastic. Highlights: Lignocellulosic bioplastic was prepared by DES pretreatment of corn stover.Oxidized cellulose was used to reinforce the lignocellulosic bioplastic.The tensile strength of the bioplastic was 62.36 MPa after the reinforcement process.Trieth‐oxy(octyl)silane was employed to improve water stability.The water contact angle of the bioplastic was increased from 8.50° to 121.9°. [ABSTRACT FROM AUTHOR]

Polylactic acid (PLA), a biomass material, has garnered increasing interest as a biodegradable alternative for the production of eco-friendly plastics. Accordingly, the sustainable synthesis of lactic acid (LA) and its derivatives from biomass sources is emerging as a viable approach. In this work, an In-TS-1 zeolite with exceptional catalytic activity and stability was successfully synthesized using a hydrothermal method and applied for the efficient one-pot conversion of fructose into methyl lactate (MLA). Characterization of the resulting catalysts, including pyridine-adsorbed Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, ultraviolet-visible diffuse reflectance spectroscopy, and energy dispersive X-ray spectroscopy for elemental mapping, confirmed that the uniform dispersion of indium (In) species contributed to its favorable acidity and significantly boosted the reaction efficiency. Under optimized reaction conditions, a remarkable MLA yield of 71.9% was achieved upon the complete conversion of fructose. The selectivity of MLA remained consistent over 14 cycles, underscoring its extraordinary stability under hydrothermal conditions attributed to the confinement of In species within the zeolite framework. This research technique establishes a potential strategy for the large-scale manufacture of LA and its esters, offering a sustainable and efficient path for the development of biodegradable plastics. [ABSTRACT FROM AUTHOR]

This review article provides a thorough overview of barrier coating materials that have been used in food packaging with a focus on biodegradable (bio-based or petroleum-based) materials, such as lipids, proteins, polysaccharides, agriculture waste and polyesters. The goal is to provide an opportunity to acknowledge progress made in this field, focusing on modifications made to coatings. These modifications aim to address the shortcomings of biodegradable substrates (either plastic or paper) and improve their performance, enabling them to compete with traditional petroleum-based food packaging materials. This includes their barrier against water vapor and oxygen, mechanical and surface characteristics (sealability and adhesion), as well as antimicrobial properties. The barrier of most biodegradable polymers underperforms in comparison with petroleum-based non-biodegradable polymers, which possess either high water vapor barrier or high oxygen barrier. Coating technology is a promising solution particularly in barrier improvement of biodegradable polymers. Currently, there are only metallized, or inorganic nanosheet coatings available for biodegradable films that meet food packaging requirements. There are some challenges in this field, for example, being able to retain the coating's biodegradability despite applied modifications to improve it's performance, the large-scale fabrication of biodegradable coatings, the coating's delamination and heat-sealability during service time, and the migration of the coating into the packaged food. Moreover, green chemistry and its sustainability needs in biodegradable polymeric coatings are also discussed regarding new ideas and possible directions for widespread application of coatings in food packaging. This is the first review that specifically summarizes biodegradable coatings on plastic and paper substrates with a focus on coating modifications to improve the performance of the base substrate to meet the required properties for food packaging applications. [ABSTRACT FROM AUTHOR]

Microbeads find widespread usage in personal care items and cosmetics, serving as exfoliants or scrubbing agents. Their micro-scale size poses challenges in effective drainage capture and given their origin from non-biodegradable oil-based plastics, this contributes substantially to marine pollution. In this study, microbeads were prepared by a simple yet scalable melt homogenization method using four types of polyhydroxyalkanoates (PHA), namely poly[(R)-3-hydroxybutyrate] (P(3HB)), poly[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyvalerate] (P(3HB-co-3HV)), poly[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyhexanoate] (P(3HB-co-3HHx)) and poly[(R)-3-hydroxybutyrate-co-(R)-4-hydroxyvalerate] (P(3HB-co-4HB)). Microbeads with different surface smoothness, compressive strength (6.2–13.3 MPa) and diameter (from 1 ~ 150 μm) could be produced. The microbeads were subjected to a comprehensive degradation analysis using three techniques: enzymatic, Biochemical Oxygen Demand (BOD) evaluations, and in situ degradation tests in the deep-sea off Misaki Port in the northern Pacific Ocean (depth of 757 m). Qualitatively, results from enzymatic and in situ degradation demonstrated significant degradation within one week and five months, respectively. Quantitatively, BOD findings indicated that all PHA microbeads degraded similarly to cellulose (~ 85% biodegradability in 25 days). In conclusion, PHA microbeads from this study exhibit promising potential as alternatives to conventional non-biodegradable microbeads. [ABSTRACT FROM AUTHOR]

This comprehensive review addresses the vital environmental concerns posed by conventional petroleum-based plastics, particularly in the context of the packaging industry's extensive reliance on these materials. As nearly 99% of plastics originate from non-renewable petrochemical sources and their non-biodegradable nature leads to widespread waste accumulation and harmful emissions upon disposal, the need for sustainable alternatives has become paramount. This paper explores the escalating environmental and health repercussions linked to traditional plastics, underscored by global initiatives, including restrictions on single-use plastics, aimed at mitigating these challenges. In response, the paper highlights the growing interest in environmental friendly biopolymers, which can be sourced from renewable biological materials or synthesized from biopolymers such as starch, casein etc. The classification of biopolymers into three primary categories; natural biopolymers, microbial fermentation-derived biopolymers, and polymerized monomers from biomass is comprehensively examined. Furthermore, the paper emphasizes the pivotal role of biopolymer properties, such as barrier characteristics, mechanical strength, heat resistance, biodegradability, flexibility, food contact safety, and cost-effectiveness, in determining their suitability for packaging applications. It also stresses the importance of conducting life cycle assessment (LCA) to holistically evaluate the environmental sustainability of biopolymers. This review highlights the potential of integrating biopolymers into packaging materials as a promising avenue to reduce the adverse environmental impact of traditional plastic production. These biodegradable materials, with their diverse properties and renewability, offer a sustainable approach to mitigating plastic waste and lowering greenhouse gas emissions. However, further research, development, and collaborative efforts are essential to optimize biopolymer performance, reduce production costs, and facilitate broader adoption. Embracing biodegradable polymers represents a commitment to resource efficiency, waste reduction, and environmental preservation, fostering a more sustainable and ecofriendly future. [ABSTRACT FROM AUTHOR]

2-Pyrone-4,6-dicarboxylic acid (PDC), a chemically stable pseudo-aromatic dicarboxylic acid, is a promising building block compound for manufacturing biodegradable polyesters. This study aimed to construct high-performance cell factories enabling the efficient production of PDC from glucose. Firstly, the effective enzymes of the PDC biosynthetic pathway were overexpressed on the chromosome of the 3-dehydroshikimate overproducing strain. Consequently, the one-step biosynthesis of PDC from glucose was achieved. Further, the PDC production was enhanced by multi-copy integration of the key gene PsligC encoding 4-carboxy-2-hydroxymuconate-6-semialdehyde dehydrogenase and co-expression of Vitreoscilla hemoglobin. Subsequently, the PDC production was substantially improved by redistributing the metabolic flux for cell growth and PDC biosynthesis based on dynamically downregulating the expression of pyruvate kinase. The resultant strain PDC50 produced 129.37 g/L PDC from glucose within 78 h under fed-batch fermentation conditions, with a yield of 0.528 mol/mol and an average productivity of 1.65 g/L/h. The findings of this study lay the foundation for the potential industrial production of PDC. • Biosynthesis of PDC from glucose was achieved in E. coli by combinatorial pathway engineering. • Heterologous expression of hemoglobin was used to increase PDC production. • Dynamic downregulation of pykA was employed to balance cell growth and PDC biosynthesis. • An efficient cell factory enabling potential industrial production of PDC was constructed. [ABSTRACT FROM AUTHOR]

In the recent decade, nanoparticles (NPs) have had enormous implications in cancer biomedicine, including research, diagnosis, and therapy. However, their broad application still faces obstacles due to some practical limitations and requires further development. Recently, there has been more interest in the coated class of nanoparticles to address those challenges. Chitosan‐coated NPs are simple to produce, biodegradable, biocompatible, exhibit antibacterial activity, and have less cytotoxicity. This study provides an updated and comprehensive overview of the application of chitosan‐coated NPs as a promising class of NPs in cancer biomedicine. Additionally, we discussed chitosan‐coated lipid, metal, and polymer‐based nanoparticles in biomedical applications. Furthermore, different coating methods and production/characterization procedures were reviewed. Moreover, the biological and physicochemical advantages of chitosan‐coated NPs, including facilitated controlled release, greater physicochemical stability, improved cell/tissue interaction, and enhanced bioavailability of medications, were highlighted. Finally, the prospects of chitosan‐coated NPs in cancer biomedicine were discussed. [ABSTRACT FROM AUTHOR]

Plastics offer many advantages and are widely used in various fields. Nevertheless, most plastics derived from petroleum are slow to degrade due to their stable polymer structure, posing serious threats to organisms and ecosystems. Thus, developing environmentally friendly and biodegradable plastics is imperative. In this study, biodegradable cellulose/multi-walled carbon nanotube (MCNT) hybrid gels and films with improved ultraviolet-shielding properties were successfully prepared using cotton textile waste as a resource. It was proven that MCNTs can be dispersed evenly in cellulose without any chemical or physical pretreatment. It was found that the contents of MCNTs had obvious effects on the structures and properties of hybrid films. Particularly, the averaged transmittance of cellulose/MCNT composite films in the range of 320–400 nm (T320–400) and 290–320 nm (T290–320) can be as low as 19.91% and 16.09%, when the content of MCNTs was 4.0%, much lower than those of pure cellulose films (T320–400: 84.12% and T290–320: 80.03%). Meanwhile, the water contact angles of the cellulose/MCNT films were increased by increasing the content of MCNTs. Most importantly, the mechanical performance of cellulose/MCNT films could be controlled by the additives of glycerol and MCNTs. The tensile strength of the cellulose/MCNT films was able to reach as high as 20.58 MPa, while the elongation at break was about 31.35%. To summarize, transparent cellulose/MCNT composites with enhanced ultraviolet-shielding properties can be manufactured successfully from low-cost cotton textile waste, which is beneficial not only in terms of environmental protection, but also the utilization of natural resources. [ABSTRACT FROM AUTHOR]

The improper disposal of plastics is a growing concern due to increasing global environmental problems such as the rise of CO2 emissions, diminishing petroleum sources, and pollution, which necessitates the research and development of biodegradable materials as an alternative to conventional packaging materials. The purpose of this research was to analyse the properties of biodegradable polymer blends of thermoplastic potato starch (TPS) and polylactide, (PLA) without and with the addition of citric acid (CA) as a potential compatibilizer and plasticizer. The prepared blends were subjected to a comprehensive physicochemical characterization, which included: FTIR-ATR spectroscopy, morphological analysis by scanning electron microscopy (SEM), determination of thermal and mechanical properties by differential scanning calorimetry (DSC), water vapour permeability (WVP), as well as biodegradation testing in soil. The obtained results indicate an improvement in adhesion between the TPS and PLA phases due to the addition of citric acid, better homogeneity of the structure, and greater compatibility of the polymer blends, leading to better thermal, mechanical and barrier properties of the studied biodegradable TPS/PLA polymer blends. After conducting the comprehensive research outlined in this paper, it has been determined that the addition of 5 wt.% of citric acid serves as an effective compatibilizer and plasticizer. This supplementation achieves an optimal equilibrium across thermal, mechanical, morphological, and barrier properties, while also promoting material sustainability through biodegradation. In conclusion, it can be stated that the use of thermoplastic starch in TPS/PLA blends accelerates the biodegradation of PLA as a slowly biodegradable polymer. While the addition of citric acid offers significant advantages for TPS/PLA blends, further research is needed to optimize the formulation and processing parameters to achieve the desired balance between mechanical strength, thermal and barrier properties and biodegradability. [ABSTRACT FROM AUTHOR]

The surge in global utilization of petroleum-based plastics, which notably heightened during the COVID-19 pandemic, has substantially increased its harm to ecosystems. Considering the escalating environmental impact, a pivotal shift towards bioplastics usage is imperative. Exploring and implementing bioplastics as a viable alternative could mitigate the ecological burden posed by traditional plastics. Macroalgae is a potential feedstock for the production of bioplastics due to its abundance, fast growth, and high cellulose and sugar content. Researchers have recently explored various methods for extracting and converting macroalgae into bioplastic. Some of the key challenges in the production of macroalgae bioplastics are the high costs of large-scale production and the need to optimize the extraction and conversion processes to obtain high-quality bioplastics. However, the potential benefits of using macroalgae for bioplastic production include reducing plastic waste and greenhouse gas emissions, using healthier materials in various life practices, and developing a promising area for future research and development. Also, bioplastic provides job opportunities in free enterprise and contributes to various applications such as packaging, medical devices, electronics, textiles, and cosmetics. The presented review aims to discuss the problem of petroleum-based plastic, bioplastic extraction from macroalgae, bioplastic properties, biodegradability, its various applications, and its production challenges. [ABSTRACT FROM AUTHOR]

In this study, hydrothermal co-liquefaction of restaurant waste for biocrude production was conducted. The feedstock was resembled using the organic fraction of restaurant waste and low-density polyethylene, polypropylene, polystyrene, and polyethylene terephthalate, four plastic types commonly present in municipal solid waste. Using design of experiment and a face-centered central composite design, three factors (feedstock plastic fraction, temperature, time) were varied at three levels each: feedstock plastic fraction (0, 0.25, 0.5), temperature (290 °C, 330 °C, 370 °C), and reaction time (0 min, 30 min, 60 min). The literature reports positive synergistic interactions in hydrothermal co-liquefaction of biomass and plastics; however, in this work, only negative synergistic interactions could be observed. A reason could be the high thermal stability of produced fatty acids that give little room for interactions with plastics. At the same time, mass might transfer to other product phases. [ABSTRACT FROM AUTHOR]

A nonthermal, pulsed spark discharge is applied to three polymer powders in Ar and Ar–H2 ${{\rm{H}}}_{2}$ gas mixtures. Hydrogen is introduced to assess plasma‐driven decomposition. Gaseous decomposition products, including methane, acetylene, and ethylene, are observed with Fourier‐transform infrared (FTIR). Surface modifications are observed on the residual polymer via attenuated total internal reflection‐FTIR. Time‐averaged rotational, vibrational, and excitation temperatures are characterized in the discharge. The plasma density is found to be around 3×1022 m−3 $3\times 1{0}^{22}\unicode{x0200A}{{\rm{m}}}^{-3}$, with rotational and vibrational temperatures ranging from 1500 to 2200 K and an excitation temperature of 1–2 eV. While spark properties did not change with either gas composition or polymer composition, it was determined that the addition of hydrogen promoted higher concentrations of gaseous phase products (promoting hydrogenolysis). [ABSTRACT FROM AUTHOR]

The topic of riverine microplastics is of great interest to the general public, yet the univocal scientific knowledge on this topic is limited. This review investigated the occurrence of microplastics in 6 major European rivers and their tributaries based on the results from 29 studies. We examined the reviewed studies in regard to data quality and reproducibility and assessed the abundance of microplastics in different sections of the water column. Furthermore, we investigated the chemical composition and potential origin of the reported riverine microplastics. We found that polystyrene, polypropylene, and polyethylene were the most abundant polymer types. The majority of primary microplastics arose from the industry sector as well as from personal care and cleaning products, whereas secondary microplastics constituted fibers from synthetic textiles and fragments of diverse origins. We highlighted the diversity of experimental and analytical approaches that could lead to high uncertainties in the measurements of microplastics abundance. Furthermore, the presence of microplastics in rivers was found to vary spatially likely due to point and nonpoint pollution sources of anthropogenic activities. Heterogenous environmental processes impacted the fate of microplastics characterized by various forms, sizes, and densities, in different ways. This impeded the identification of representative quantitative measurements of microplastics across different time frames. We advocate for the development of standardized protocols by the research community to ensure higher reproducibility of sampling, processing, and analysis of microplastics in aquatic environments. We recommend long‐term and site‐specific monitoring on microplastics with high data comparability to better inform policy making. This article is categorized under:Science of Water > Water QualityWater and Life > Conservation, Management, and Awareness [ABSTRACT FROM AUTHOR]

In light of increasing apprehensions surrounding the environmental impact of non-biodegradable plastics, there has been a surge in the exploration of biodegradable films as a viable and sustainable alternative. This research has focused on developing Tara gum (TG)-based films incorporated with Lavender essential oil (LEO) at different concentrations (5–20% w/w) to improve the properties of the films. According to the results, GC-MS analysis confirmed the presence of linalool and linalyl acetate as the major compounds in LEO. Among the composite films, the sample containing 5% (w/w) LEO exhibited the highest homogeneity, as evidenced by SEM micrographs, and the CLSM image demonstrated the absence of any clustering or coalescence of LEO within this film. FTIR spectra demonstrated intermolecular interactions between TG and LEO, as evidenced by a new peak at 1458 cm−1 in the LEO-loaded films. The addition of LEO resulted in a significant decrease in the water content (WC) and water solubility (WS) of the films. Furthermore, LEO incorporation improved the contact angle (CA) of the films up to 1.5 times. The TG-LEO films exhibited good transparency, higher elongation at break (EB), and lower Young's modulus (YM). Additionally, LEO positively affected the antioxidant and antimicrobial properties of the films. Overall, the results authenticated the hypothesis of this study and indicated that TG-LEO films have great potential as biodegradable films with promising functionalities for food packaging applications. [ABSTRACT FROM AUTHOR]

Plastic biodegradation has emerged as a sustainable approach and green alternative in handling the ever-increasing accumulation of plastic wastes in the environment. The complete biodegradation of polyethylene terephthalate is one of the most recent breakthroughs in the field of plastic biodegradation. Despite the success, the effective and complete biodegradation of a wide variety of plastics is still far from the practical implementation, and an on-going effort has been mainly devoted to the exploration of novel microorganisms and enzymes for plastic biodegradation. However, alternative strategies which enhance the existing biodegradation process should not be neglected in the continuous advancement of this field. Thus, this review highlights various strategies which have shown to improve the biodegradation of plastics, which include the pretreatment of plastics using UV irradiation, thermal, or chemical treatments to increase the susceptibility of plastics toward microbial action. Alternative pretreatment strategies are also suggested and compared with the existing techniques. Besides, the effects of additives such as pro-oxidants, natural polymers, and surfactants on plastic biodegradation are discussed. In addition, considerations governing the biodegradation performance, such as the formulation of biodegradation medium, cell-free biocatalysis, and physico-chemical properties of plastics, are addressed. Lastly, the challenges and future prospects for the advancement of plastic biodegradation are also highlighted. [ABSTRACT FROM AUTHOR]

[Display omitted] • Hydrophobic ZIF-8/SA monolithic materials were fabricated via in situ synthesis. • The cooperation of SA, PDMS, and ZIF-8 significantly enhanced adsorption capacity. • The composites displayed rapid kinetic adsorption. • The composites have remarkable absorption recyclability. Microplastics (MPs), a newly emerging class of environmental contaminants, pose a severe threat to the entire ecosystem. The development of efficient and environmentally responsible adsorbents for removing the MPs is a particularly urgent research. Herein, a kind of monolithic ZIF-8 based adsorbents featuring stable hydrophobicity and micropore-mesopore-macropore hierarchical porous structure were fabricated by in situ growth of ZIF-8 nanoparticles on sodium alginate (SA) framework, and using polydimethylsiloxane (PDMS) as a hydrophobic agent. The monolithic nature of ZIF-8/SA allowed an easy solid–liquid separation process for adsorbents from water environment compared to powdered materials. The hierarchical porous structure ensures a remarkable MPs removal performance. The ZIF-8/SA showed high adsorption capacities of 594, 585, and 282 mg/g for polymethyl methacrylate (PMMA), poly (vinylidene difluoride) (PVDF), and polyvinyl chloride (PVC) respectively, and rapid adsorption kinetic progress within 120 min. The ZIF-8/SA adsorbents also exhibited excellent stability in the presence of interfering ions, acid/alkali, and humic acid, and displayed adsorption performance of > 70 % even in actual aquatic environment such as tap water, river water, and seawater. The results of characterizations showed that the synergistic effect of electrostatic interaction, hydrogen bonding, hydrophobic force, and van der Waals force was the main adsorption mechanism. The well-designed hydrophobic ZIF-8/SA monolithic materials would be promising to rapidly remove the MPs from the water environment. [ABSTRACT FROM AUTHOR]

• Interaction of plastic and scrap tyre during co-pyrolysis is plastic-specific. • Mixing PP or LDPE with tyre can promote aliphatic hydrocarbon and suppress PAHs. • Mixing PS with tyre can suppress PAHs and enhance MAs production, especially BTEX. • 75 wt% LDPE or PS with tyre at 600 °C yields sulphur-free pyrolytic oil. • Tyre char can promote cracking reactions in LDPE thermal degradation. Fast co-pyrolysis offers a sustainable solution for upcycling polymer waste, including scrap tyre and plastics. Previous studies primarily focused on slow heating rates, neglecting synergistic mechanisms and sulphur transformation in co-pyrolysis with tyre. This research explored fast co-pyrolysis of scrap tyre with polypropylene (PP), low-density polyethylene (LDPE), and polystyrene (PS) to understand synergistic effects and sulphur transformation mechanisms. A pronounced synergy was observed between scrap tyre and plastics, with the nature of the synergy being plastic-type dependent. Remarkably, blending 75 wt% PS or LDPE with tyre effectively eliminated sulphur-bearing compounds in the liquid product. This reduction in sulphur content can substantially mitigate the release of hazardous materials into the environment, emphasizing the environmental significance of co-pyrolysis. The synergy between PP or LDPE and tyre amplified the production of lighter hydrocarbons, while PS's interaction led to the creation of monocyclic aromatics. These findings offer insights into the intricate chemistry of scrap tyre and plastic interactions and highlight the potential of co-pyrolysis in waste management. By converting potential pollutants into valuable products, this method can significantly reduce the release of hazardous materials into the environment. [ABSTRACT FROM AUTHOR]

Ammonia, a vital component in the synthesis of fertilizers, plastics, and explosives, is traditionally produced via the energy‐intensive and environmentally detrimental Haber–Bosch process. Given its considerable energy consumption and significant greenhouse gas emissions, there is a growing shift toward electrocatalytic ammonia synthesis as an eco‐friendly alternative. However, developing efficient electrocatalysts capable of achieving high selectivity, Faraday efficiency, and yield under ambient conditions remains a significant challenge. This review delves into the decades‐long research into electrocatalytic ammonia synthesis, highlighting the evolution of fundamental principles, theoretical descriptors, and reaction mechanisms. An in‐depth analysis of the nitrogen reduction reaction (NRR) and nitrate reduction reaction (NitRR) is provided, with a focus on their electrocatalysts. Additionally, the theories behind electrocatalyst design for ammonia synthesis are examined, including the Gibbs free energy approach, Sabatier principle, d‐band center theory, and orbital spin states. The review culminates in a comprehensive overview of the current challenges and prospective future directions in electrocatalyst development for NRR and NitRR, paving the way for more sustainable methods of ammonia production. [ABSTRACT FROM AUTHOR]

This study aimed to investigate the sustainable use of recycled plastics, specifically polypropylene (PP) and high-density polyethylene (HDPE), in the manufacture of geogrids for geotechnical and civil engineering applications. Plastics were collected from a recycling center, specifically targeting containers used for food, cleaning products, and other domestic packaging items. These plastics were sorted according to the Möbius triangle classification system, with HDPE (#2) and PP (#5) being the primary categories of interest. The research methodologically evaluates the mechanical properties of PP/HDPE (0/100, 25/75, 50/50, 75/25 and 100/0% w/w) composites through tensile and flexural tests, exploring various compositions and configurations of geogrids. The results highlight the superiority of pure recycled HDPE processed into 1.3 mm thick laminated yarns and hot air welded for 20 to 30 s, exhibiting a deformation exceeding 60% in comparison to the PP/HDPE composites. Through SolidWorks® Simulation, it was shown that the adoption of a trigonal geogrid geometry optimizes force distribution and tensile strength, significantly improving slope stabilization efficiency. Based on the results obtained, a laboratory-scale prototype geogrid was developed using an extrusion process. The results underscore the importance of careful composite design and yarn configuration selection to achieve the desired mechanical properties and performance in geogrid applications. It emphasizes the potential of recycled plastics as a viable and environmentally friendly solution for stabilizing slopes, contributing to the reduction in plastic waste and promoting sustainable construction practices. [ABSTRACT FROM AUTHOR]

Plastic pollution poses a significant environmental challenge, necessitating the investigation of bioplastics with reduced end-of-life impact. This study systematically characterizes four promising bioplastics—polybutylene adipate terephthalate (PBAT), polybutylene succinate (PBS), poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), and polylactic acid (PLA). Through a comprehensive analysis of their chemical, thermal, and mechanical properties, we elucidate their structural intricacies, processing behaviors, and potential morphologies. Employing an environmentally friendly process utilizing supercritical carbon dioxide, we successfully produced porous materials with microcellular structures. PBAT, PBS, and PLA exhibit closed-cell morphologies, while PHBV presents open cells, reflecting their distinct overall properties. Notably, PBAT foam demonstrated an average porous area of 1030.86 μm2, PBS showed an average porous area of 673 μm2, PHBV displayed open pores with an average area of 116.6 μm2, and PLA exhibited an average porous area of 620 μm2. Despite the intricacies involved in correlating morphology with material properties, the observed variations in pore area sizes align with the findings from chemical, thermal, and mechanical characterization. This alignment enhances our understanding of the morphological characteristics of each sample. Therefore, here, we report an advancement and comprehensive research in bioplastics, offering deeper insights into their properties and potential morphologies with an easy sustainable foaming process. The alignment of the process with sustainability principles, coupled with the unique features of each polymer, positions them as environmentally conscious and versatile materials for a range of applications. [ABSTRACT FROM AUTHOR]

The increased use of plastics in industrial and agricultural applications has led to high levels of pollution worldwide and is a significant challenge. To address this plastic pollution, conventional methods such as landfills and incineration are used, leading to further challenges such as the generation of greenhouse gas emissions. Therefore, increasing interest has been directed to identifying alternative methods to dispose of plastic waste from agriculture. The novelty of the current research arose from the lack of critical reviews on how 3-Dimensional (3D) printing was adopted for recycling plastics, its application in the production of agricultural plastics, and its specific benefits, disadvantages, and limitations in recycling plastics. The review paper offers novel insights regarding the application of 3D printing methods including Fused Particle Fabrication (FPF), Hot Melt Extrusion (HME), and Fused Deposition Modelling (FDM) to make filaments from plastics. However, the methods were adopted in local recycling setups where only small quantities of the raw materials were considered. Data was collected using a systematic review involving 39 studies. Findings showed that the application of the 3D printing methods led to the generation of agricultural plastics such as Polylactic Acid (PLA), Acrylonitrile Butadiene Styrene (ABS), Polyethylene Terephthalate (PET), and High-Density Polyethylene (HDPE), which were found to have properties comparable to those of virgin plastic, suggesting the viability of 3D printing in managing plastic pollution. However, limitations were also associated with the 3D printing methods; 3D-printed plastics deteriorated rapidly under Ultraviolet (UV) light and are non-biodegradable, posing further risks of plastic pollution. However, UV stabilization helps reduce plastic deterioration, thus increasing longevity and reducing disposal. Future directions emphasize identifying methods to reduce the deterioration of 3D-printed agricultural plastics and increasing their longevity in addition to UV stability. [ABSTRACT FROM AUTHOR]

Polymeric materials undergo degradation when exposed to outdoor conditions due to the synergistic effects of sunlight, air, heat, and moisture. The degradation can lead to a decline in mechanical properties, fading, surface cracking, and haziness, attributed to the cleavage of the polymer chains and oxidation reactions. Accelerated weathering testing is a useful technique to evaluate the comparative photodegradation of materials within a reasonable timeframe. This review gives an overview of the different degradation mechanisms occurring in conventional plastics and bio-based materials. Case studies on accelerated weathering and its effect on the mechanical properties of conventional plastics and biocomposites are discussed. Different techniques for analysing volatile organic emissions (VOCs) have been summarized and studies highlighting the characterization of VOCs from aged plastics and biocomposites after aging have been cited. [ABSTRACT FROM AUTHOR]

Plastic containers, commonly produced from non-biodegradable petroleum-based plastics such as polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET), raise significant environmental concerns due to their persistence. The disposal of agricultural waste, specifically rice straw (RS), through burning, further compounds these environmental issues. In response, this study explores the integration of polylactic acid (PLA), a biodegradable material, with RS using a twin-screw extruder and injection process, resulting in the creation of a biodegradable packaging material. The inclusion of RS led to a decrease in the melt flow rate, thermal stability, and tensile strength, while concurrently enhancing the hydrophilic properties of the composite polymers. Additionally, the incorporation of maleic anhydride (MA) contributed to a reduction in the water absorption rate. The optimized formulation underwent migration testing and met the standards for food packaging products. Furthermore, no MA migration was detected from the composite. This approach not only provides a practical solution for the disposal of RS, but also serves as an environmentally-friendly alternative to conventional synthetic plastic waste. [ABSTRACT FROM AUTHOR]

Non-degradable plastics of petrochemical origin are a contemporary problem of society. Due to the large amount of plastic waste, there are problems with their disposal or storage, where the most common types of plastic waste are disposable tableware, bags, packaging, bottles, and containers, and not all of them can be recycled. Due to growing ecological awareness, interest in the topics of biodegradable materials suitable for disposable items has begun to reduce the consumption of non-degradable plastics. An example of such materials are biodegradable biopolymers and their derivatives, which can be used to create the so-called bioplastics and biopolymer blends. In this article, gelatine blends modified with polysaccharides (e.g., agarose or carrageenan) were created and tested in order to obtain a stable biopolymer coating. Various techniques were used to characterize the resulting bioplastics, including Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)/differential scanning calorimetry (DSC), contact angle measurements, and surface energy characterization. The influence of thermal and microbiological degradation on the properties of the blends was also investigated. From the analysis, it can be observed that the addition of agarose increased the hardness of the mixture by 27% compared to the control sample without the addition of polysaccharides. In addition, there was an increase in the surface energy (24%), softening point (15%), and glass transition temperature (14%) compared to the control sample. The addition of starch to the gelatine matrix increased the softening point by 15% and the glass transition temperature by 6%. After aging, both compounds showed an increase in hardness of 26% and a decrease in tensile strength of 60%. This offers an opportunity as application materials in the form of biopolymer coatings, dietary supplements, skin care products, short-term and single-contact decorative elements, food, medical, floriculture, and decorative industries. [ABSTRACT FROM AUTHOR]

Pistachio (Pistacia vera L.) is consumed in almost every part of the world enclosed in shells that are thrown out in baskets. Similarly, hulls separated from pistachio are discarded as waste in food processing industries. These waste materials contain functional constituents having immense industrial and nutraceutical applications. This review article summarizes the scientific investigations regarding the functional constituents and bioactive compounds in pistachio shells (PSs) and pistachio hulls (PHs). It also highlights the nutraceutical potential exhibited by functionally active compounds as well as their potential applications in various industries including nutraceutical, medicinal, and feed industries together with biosynthetic development of useful products and wastewater treatment. Pistachio waste (PW) comprising PS and PH is a rich source of various bioactive compounds. PS is full of lignin, cellulose, and hemicellulose. PH is an excellent source of carbohydrates (80.64 ± 0.98%) (including glucose, galactose, rhamnose, arabinose, xylose, mannose, galacturonic acid) as well as ash (6.32 ± 0.26%) and proteins (1.80 ± 0.28%) with small amounts of fats (0.04 ± 0.005%). Owing to its composition, PW can be beneficial in many nutraceuticals, including antioxidation, cytoprotection, anti-obesity, anti-diabetic, anti-melanogenesis, neuroprotection, anti-cancer, anti-mutagenesis, anti-inflammation, and anti-microbial. The waste materials have vast applications in the food industry, such as bio-preservation of oils and meat products, prevention of enzymatic browning in fruits, vegetables, and mushrooms, development of functional cereal and dairy products, production of food enzymes, emulsions, and manufacturing of biodegradable films for food packaging. The use of these waste products to develop and design novel functional foods with improved quality is important for both food industries and food sustainability. [ABSTRACT FROM AUTHOR]

The root cause of global pollution is the reflection of usage of non-degradable plastics. The solutions and methods to mitigate the plastic pollution are in high demand. The application of green technology in polymer science from the marine resource gives stability to the ecosystem. The bio-composite films were fabricated using gelatin of fish scale, agar of seaweed and chitosan of shrimp shell waste by a solvent casting technique. The plasticity and bioactivity enhanced using glycerol and clove essential oil. The physic-chemical and mechanical properties of the film were evaluated against the range of test of thickness, tensile strength, elongation at break, puncture resistance, water vapor permeability, Attenuated Total Reflection—Fourier Transform Infrared spectroscopy, X-ray diffraction and atomic force microscopy. The characteristics of active packaging mechanism assessed based on antimicrobial and antioxidative properties. A level of 1.5% clove essential oil ration was given desirable properties of active packaging material. The biodegradability was calculated in terms of percentage weight loss under the soil burial and water immersion test. The biodegradation process of composite film took 21 days in soil and 158 in water. Hence, the bio-composite film prepared from green technology is a promising alternative to the conventional plastic to mitigate plastic pollution. [ABSTRACT FROM AUTHOR]

Functional antibacterial textile materials are in great demand in the medical sector. In this paper, we propose a facile, eco-friendly approach to the design of antibacterial biodegradable cotton fabrics. Cotton fiber fabrics were enhanced with a chitosan coating loaded with plant extracts and essential oils. We employed Fourier-transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS), UV–Vis spectrophotometry, optical microscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA) to characterize the color, structure, and thermal properties of the modified fabrics. The fabrics were found to effectively induce growth inhibition of Gram-positive and Gram-negative bacteria, especially when a synergic system of aloe vera extract and cinnamon essential oil was applied in the coating formulation. Additionally, we observed significant color and weight changes after 5, 10, and 20 days in soil biodegradability tests. Given the straightforward modification process and the use of non-toxic natural materials, these innovative bio-based and biodegradable cotton fabrics show great promise as protective antimicrobial textiles for healthcare applications. [ABSTRACT FROM AUTHOR]

Developing dynamic chemistry for polymeric materials offers chemical solutions to solve key problems associated with current plastics. Mechanical performance and dynamic function are equally important in material design because the former determines the application scope and the latter enables chemical recycling and hence sustainability. However, it is a long‐term challenge to balance the subtle trade‐off between mechanical robustness and dynamic properties in a single material. The rise of dynamic chemistry, including supramolecular and dynamic covalent chemistry, provides many opportunities and versatile molecular tools for designing constitutionally dynamic materials that can adapt, repair, and recycle. Facing the growing social need for developing advanced sustainable materials without compromising properties, recent progress showing how the toolbox of dynamic chemistry can be explored to enable high‐performance sustainable materials by molecular engineering strategies is discussed here. The state of the art and recent milestones are summarized and discussed, followed by an outlook toward future opportunities and challenges present in this field. [ABSTRACT FROM AUTHOR]

Plastic accumulation is a severe threat to the environment due to its resistivity to thermal, mechanical and biological processes. In recent years, microbial degradation of plastic waste disposal is of interest because of its eco-friendly nature. In this study, a total of 33 fungi were isolated from the plastisphere and out of which 28 fungal species showed halo zone of clearance in agarized LDPE media. The fungus showing highest zone of clearance was further used to evaluate its degradation potential. Based on morphological and molecular technique, the fungus was identified as Cladosporium sphaerospermum. The biodegradation of LDPE by C. sphaerospermum was evaluated by various methods. The exposure of LDPE with C. sphaerospermum resulted in weight loss (15.23%) in seven days, higher reduction rate (0.0224/day) and lower half-life (30.93 days). FTIR analysis showed changes in functional group and increased carbonyl index in LDPE treated with C. sphaerospermum. SEMimages evidenced the formation of pits, surface aberrations and grooves on the LDPE film treated with the fungus whereas the untreated control LDPE film showed no change. AFM analysis confirmed the surface changes and roughness in fungus treated LDPE film. This might be due to the extracellular lignolytic enzymes secreted by C. sphaerospermum grown on LDPE. The degradation of polyethylene by Short chain alkanes such as dodecane, hexasiloxane and silane were identified in the extract of fungus incubated with LDPE film through GC–MS analysis which might be due to the degradation of LDPE film by C. sphaerospermum. This was the first report on the LDPE degradation by C. sphaerospermum in very short duration which enables green scavenging of plastic wastes. [ABSTRACT FROM AUTHOR]

Biodegradable plastics, represented by polylactic acid (PLA), are considered suitable alternatives to nondegradable commodity plastics; however, their degradation through microbial decomposition is seen as a waste of carbon resources and inevitably brings about CO2 emission. Alternatively, waste PLA plastics can be utilized as feedstocks for the sustainable production of value-added chemicals, which not only avoids a carbon footprint but also realizes upcycling of plastic waste. Here, we show a cascade system that combines alkali-induced depolymerization, pulsed electrooxidation, and electrochemical reductive amination to produce alanine with an overall yield of 69% under near ambient conditions. Specifically, we first implement an alkali catalyst in an aqueous solution to depolymerize PLA into lactate. The obtained PLA hydrolysate is directly utilized as both feedstock and electrolyte for pyruvate production over a nickel hydroxide-supported Pd electrocatalyst (Pd/Ni(OH)2) via a pulsed potential, which is followed by the transformation of pyruvate into alanine using a TiO2 catalyst. This cascade process for alanine production benefits from high efficiencies maintained in three consecutive processes, mild operation conditions, and the use of cost-effective feedstocks (plastic wastes), without suffering harsh conditions and expensive feedstock consumption required by conventional biological and chemical approaches for alanine synthesis, respectively. [ABSTRACT FROM AUTHOR]