Search

Achieving good quality Ohmic contacts to van der Waals materials is a challenge, since at the interface between metal and van der Waals material different conditions can occur, ranging from the presence of a large energy barrier between the two materials to the metallization of the layered material below the contacts. In black phosphorus (bP), a further challenge is its high reactivity to oxygen and moisture, since the presence of uncontrolled oxidation can substantially change the behavior of the contacts. Here we study three of the most commonly used metals as contacts to bP, chromium, titanium, and nickel, and investigate their influence on contact resistance against the variability between different flakes and different samples. We investigate the gate dependence of the current–voltage characteristics of field–effect transistors fabricated with these metals on bP, observing good linearity in the accumulation regime for all metals investigated. Using the transfer length method, from an analysis of ten devices, both at room temperature and at low temperature, Ni results to provide the lowest contact resistance to bP and minimum scattering between different devices. Moreover, we observe that our best devices approach the quantum limit for contact resistance both for Ni and for Ti contacts. [ABSTRACT FROM AUTHOR]

Morphological inhomogeneities and structural defects in organic semiconductors crucially determine the charge accumulation and lateral transport in organic thin-film transistors. Photoluminescence Electro-Modulation (PLEM) microscopy is a laser-scanning microscopy technique that relies on the modulation of the thin-film fluorescence in the presence of charge-carriers to image the spatial distribution of charges within the active organic semiconductor. Here, we present a lock-in scheme based on a scanning beam approach for increasing the PLEM microscopy resolution and contrast. The charge density in the device is modulated by a sinusoidal electrical signal, phase-locked to the scanning beam of the excitation laser. The lock-in detection scheme is achieved by acquiring a series of images with different phases between the beam scan and the electrical modulation. Application of high resolution PLEM to an organic transistor in accumulation mode demonstrates its potential to image local variations in the charge accumulation. A diffraction-limited precision of sub-300 nm and a signal to noise ratio of 21.4 dB could be achieved. [ABSTRACT FROM AUTHOR]

Thienopyrrole-dione (TI) end capped materials have recently emerged as polymorphic molecular semiconductors suitable as active layers of ambipolar light emitting transistors, photovoltaic cells and time temperature integrator devices. Here, we report the synthesis of a new derivative, namely 2,2′-([2,2′-bithiophene]-5,5′-diyl)bis(5-octyl-4-phenyl-4H-thieno[2,3-c]pyrrol-6(5H)-one) (R-NT4N), having monoreduced TI moiety (R-TI) end groups. Ring opening of the TI moiety by Grignard reagent addition followed by one-pot reduction/ring closure by triethylsilane afforded the R-TI precursor that was then exploited for the preparation of the target R-NT4N compound. Investigation of the fluorescence properties of thin films, as a function of the processing conditions, showed that different from all the other TI derivatives so far reported, R-NT4N exhibits linearly polarized fluorescent microstructures. Combined micro-Raman and confocal laser-scanning fluorescence microscopies on lithographically controlled wetting (LCW) patterned R-NT4N films allowed us to correlate the emission polarization directions with the microcrystal structures. [ABSTRACT FROM AUTHOR]

A new anthracene-based twisted oligomer combining a rigid anthracene–xylene core with diphenylamine ends 4,4′-(anthracene-9,10-diyl)bis(2,5-dimethyl-N,N-diphenylaniline), DiPAXA, is herein presented as an efficient and deep blue emitter material. By exploiting DiPAXA as an emissive layer and 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT) as a p-type semiconducting layer, we realize a blue emitting unipolar light emitting transistor (OLET) with a maximum external quantum efficiency (EQE) of 0.13%, a charge mobility up to 0.32 cm2 V−1 s−1 and CIE color coordinates of (0.18, 0.21), i.e. closer to currently available standards (PAL, NTSC). Moreover, comparison with other anthracene-based blue emitters highlights the suitability of this family of twisted anthracene–xylene compounds for unipolar blue OLET applications as a result of the enhanced performances in terms of CIE coordinates and light emission output of newly synthesized DiPAXA. [ABSTRACT FROM AUTHOR]

Background & Aims: The clinical utility of thrombomodulin-modified thrombin generation (TM-TG) in cirrhosis is uncertain. We conducted a prospective study to evaluate the prognostic value of TM-TG in cirrhosis., Methods: Patients were recruited during outpatient clinics (compensated and stable decompensated) or if admitted to our inpatient service (acutely decompensated, AD). We performed whole blood (WB) and platelet-poor plasma (PPP) TM-TG at recruitment. All patients were prospectively followed-up for bleeding/thrombosis, hepatic decompensation, and liver-related death., Results: We included 231 patients: 80 compensated, 70 stable decompensated, and 81 AD. Median follow-up was 414 days (range: 77-668). Eleven patients, all AD, experienced procedure-related bleeding. Both WB-TG and PPP-TG were more altered in bleeding vs. non-bleeding individuals (lower endogenous thrombin potential [ETP] and peak-height). However, only WB-TG could identify - at individual-patient level - those experiencing major bleeding (all having pre-procedural ETP <350 nmol/L*min). In AD, the area under the ROC curve of WB-TG ETP for bleeding was 0.854 (95%CI: 0.732-0.976), which was higher than that of PPP-TG ETP (0.676; 95%CI: 0.524-0.809). Neither WB-TG nor PPP-TG could predict development of thrombosis, mostly PVT (n=15). In compensated cirrhosis, WB-TG and PPP-TG were comparable between patients who experienced decompensation and those who did not. In decompensated cirrhosis, WB-TG and PPP-TG were more significantly altered in patients experiencing further decompensation/ACLF/liver-related death. A higher WB-TG ETP was linked to a lower risk of progression independently of MELD, Child-Pugh, and C-reactive protein (HR: 0.4, 95%CI: 95%: 0.21-0.79; p<0.01)., Conclusions: In compensated cirrhosis, WB-TG and PPP-TG do not improve risk stratification. In decompensated cirrhosis, WB-TG may be a promising tool for estimating procedure-related bleeding risk., Trial Registration Number: NA., Competing Interests: Declaration of Competing Interest AZ, EC, CB, Sg, GN, ST, PB, FPR, MS, PS have nothing to disclose. RW, JK, MR, BdL are employees of Synapse Research Institute, part of Diagnostica Stago., (Copyright © 2024 The Author(s). Published by Elsevier B.V. All rights reserved.)

Background & Aims: The underlying mechanisms and clinical impact of portal microthrombosis in severe COVID-19 are unknown. Intrapulmonary vascular dilation (IPVD)-related hypoxia has been described in severe liver diseases. We hypothesised that portal microthrombosis is associated with IPVD and fatal respiratory failure in COVID-19., Methods: Ninety-three patients who died from COVID-19 were analysed for portal microvascular damage (histology), IPVD (histology and chest-computed tomography, CT), and hypoxemia (arterial blood gas). Seventeen patients who died from COVID-19-unrelated pneumonia served as controls. Vascular lesions and microthrombi were phenotyped for endothelial (vWF) and pericyte (αSMA/PDGFR-β) markers, tissue factor (TF), viral spike protein and nucleoprotein (SP, NP), fibrinogen, and platelets (CD41a). Viral particles in vascular cells were assessed by transmission electron microscopy. Cultured pericytes were infected with SARS-CoV-2 to measure TF expression and tubulisation of human pulmonary microvascular endothelial cells was assessed upon vWF treatment., Results: IPVD was present in 16/66 patients with COVID-19, with available liver and lung histology, and was associated with younger age (62 vs. 78 years-old), longer illness (25 vs. 14 days), worsening hypoxemia (PaO 2 /FiO 2 from 209 to 89), and an increased requirement for ventilatory support (63% vs. 22%) compared to COVID-19/Non-IPVD. IPVD, absent in controls, was confirmed by chest CT. COVID-19/IPVD liver histology showed portal microthrombosis in >82.5% of portal areas, with a thicker wall of αSMA/PDGFR-β + /SP + /NP + pericytes compared with COVID-19/Non-IPVD. Thrombosed portal venules correlated with αSMA + area, whereas infected SP + /NP + pericytes expressed TF. SARS-CoV-2 viral particles were observed in portal pericytes. In vitro SARS-CoV-2 infection of pericytes upregulated TF and induced endothelial cells to overexpress vWF, which expanded human pulmonary microvascular endothelial cell tubules., Conclusions: SARS-CoV-2 infection of liver pericytes elicits a local procoagulant response associated with extensive portal microthrombosis, IPVD and worsening respiratory failure in fatal COVID-19., Impact and Implications: Vascular involvement of the liver represents a serious complication of COVID-19 infection that must be considered in the work-up of patients with long-lasting and progressively worsening respiratory failure, as it may associate with the development of intrapulmonary vascular dilations. This clinical picture is associated with a procoagulant phenotype of portal venule pericytes, which is induced by SARS-CoV-2 infection of pericytes. Both observations provide a model that may apply, at least in part, to other vascular disorders of the liver, featuring obliterative portal venopathy, similarly characterised at the clinical level by development of hypoxemia and at the histological level by phlebosclerosis and reduced calibre of the portal vein branches in the absence of cirrhosis. Moreover, our findings shed light on an overlooked player in the pathophysiology of thrombosis, i.e. pericytes, which may present a novel therapeutic target., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

Background: Reticulated platelets (RePLT) are emergency circulating platelets released to contrast peripheral platelet destruction., Aim: We conducted a prospective study to [a] characterize RePLT in cirrhosis; [b] evaluate the association between RePLT and hepatic decompensation/death., Methods: Cirrhosis patients without hepatocellular carcinoma were prospectively recruited and underwent assessment of RePLT and thrombopoietin (TPO). RePLT were evaluated by cytofluorimetry and immuno-fluorescence microscopy. Twenty healthy subjects were included as controls. Patients were followed for 6 months for hepatic decompensation and further decompensation/ACLF., Results: Forty-five patients were included (Child-Pugh [CP] A/B/C 18/11/16). Compared to controls, RePLT in cirrhosis were significantly increased (0.82% vs. 0.05%; p < 0.001) and hyperactivated (4.35% vs. 0.17%; p = 0.004). No correlation was observed between RePLT and CP, platelet count, TPO, MELD score, and C-reactive protein. TPO was lower in cirrhosis than controls (28 pg/mL vs. 52 pg/mL; p = 0.005), decreasing significantly with CP stage. In CP B/C patients (n = 27), RePLT were significantly higher in those who progressed towards further decompensation/ACLF (2.11 [0.56-2.95] vs. 0.69 [0.02-1.22]; p < 0.01). A proportion of RePLT >2% accurately identified high-risk patients (AUROC 0.818; 95%CI: 0.639-0.997; sensitivity 94%, specificity 73%)., Conclusion: RePLT in cirrhosis are increased and hyper-activated. In decompensated patients, higher RePLT appear to be associated with worse outcomes., Competing Interests: Conflict of interest None declared., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Ambipolar organic light-emitting transistors (OLETs) are extremely appealing devices for applications from sensing to communication and display realization due to their inherent capability of coupling switching and light-emitting features. However, their limited external quantum efficiency (EQE) and brightness under ambipolar bias conditions hamper the progress of OLET technology. In this context, it was recently demonstrated in multi-stacked devices that the engineering of the interface between the topmost electron-transporting organic semiconductor (e-OS) and the emission layer (EML) is crucial in optimizing the recombination of the minority charges (i.e., electrons) and to enhance EQE and brightness. Here, we introduce a new light-emitting conjugated polar polymer (CPP) in a multi-stacked OLET to improve the electron injection from e-OS to EML and to study, simultaneously, electroluminescence-related processes such as exciton formation and quenching processes. Interestingly, we observed that the highly polar groups present in the conjugate polymer induced polarization-related relevant charge-trapping phenomena with consequent modulation of the entire electrostatic field distribution and unexpected optoelectronic features. In view of the extensive use of CPPs in OLETs, the use of multifunctional CPPs for probing photophysical processes at the functional interfaces in stacked devices may speed up the improvement of the light-emission properties in OLETs.

Background: Extracellular vesicles (EVs) modulate inflammation, coagulation and vascular homeostasis in decompensated cirrhosis., Aim: To characterize the profile of plasmatic EVs in patients with decompensated cirrhosis and bacterial infections and evaluate the association between EVs and the development of hemostatic complications., Methods: We measured the levels of EVs using high-sensitivity flow cytometry and phospholipid-dependent clotting time (PPL) in a prospective cohort of hospitalized patients with acutely decompensated cirrhosis with versus without bacterial infections. A separate cohort of patients with bacterial infections without cirrhosis was also enrolled. We measured endothelium-, tissue factor (TF)-bearing, platelet- and leukocyte-derived EVs. In patients with infections, EVs were reassessed upon resolution of infection. Bleeding and thrombotic complications were recorded during 1-year follow-up., Results: Eighty patients with decompensated cirrhosis were recruited (40 each with and without bacterial infections). Electron microscopy confirmed the presence of plasma EVs. Despite no difference in total EVs and PPL, patients with cirrhosis and infection had significantly higher TF + EVs, P-Selectin + EVs (activated platelet-derived), CD14 + EVs (monocyte/macrophages derived) and CD14 + TF + EVs versus those with cirrhosis without infection. Upon infection resolution, levels of these EVs returned to those without infection. Patients with infections showed a significant association between reduced P-Selectin + EVs and bleeding complications (HR 8.0 [95%CI 1.3-48.1]), whereas high levels of leukocyte-derived EVs (CD45 + ) and CD14 + EVs were significantly associated with thrombotic complications (HR 16.4 [95%CI 1.7-160] and 10.9 [95%CI 1.13-106], respectively). Results were confirmed in a validation cohort., Conclusion: Bacterial infections are associated with particular alterations of plasma EVs profile in decompensated cirrhosis. Bacterial infections trigger the release of EVs originating from various cell types, which may tip the precarious hemostatic balance of patients with acutely decompensated cirrhosis towards hyper- or hypocoagulability., (© 2024 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

Background: Coagulation factor V (FV) deficiency is a rare bleeding disorder that is usually managed with fresh-frozen plasma. Patients with nonsense mutations may respond to treatment with readthrough agents., Objectives: To investigate whether the F5 p.Arg1161Ter mutation, causing severe FV deficiency in several patients, would be amenable to readthrough therapy., Methods: F5 mRNA and protein expression were evaluated in a F5 p.Arg1161Ter-homozygous patient. Five readthrough agents with different mechanisms of action, i.e. G418, ELX-02, PTC-124, 2,6-diaminopurine (2,6-DAP), and Amlexanox, were tested in in vitro and ex vivo models of the mutation., Results: The F5 p.Arg1161Ter-homozygous patient showed residual F5 mRNA and functional platelet FV, indicating detectable levels of natural readthrough. COS-1 cells transfected with the FV-Arg1161Ter cDNA expressed 0.7% FV activity compared to wild-type. Treatment with 0-500 μM G418, ELX-02, and 2,6-DAP dose-dependently increased FV activity up to 7.0-fold, 3.1-fold, and 10.8-fold, respectively, whereas PTC-124 and Amlexanox (alone or in combination) were ineffective. These findings were confirmed by thrombin generation assays in FV-depleted plasma reconstituted with conditioned media of treated cells. All compounds except ELX-02 showed some degree of cytotoxicity. Ex vivo differentiated megakaryocytes of the F5 p.Arg1161Ter-homozygous patient, which were negative at FV immunostaining, turned positive after treatment with all 5 readthrough agents. Notably, they were also able to internalize mutant FV rescued with G418 or 2,6-DAP, which would be required to maintain the crucial platelet FV pool in vivo., Conclusion: These findings provide in vitro and ex vivo proof-of-principle for readthrough-mediated rescue of the F5 p.Arg1161Ter mutation., Competing Interests: Declaration of competing interests T.M.H. is cofounder and shareholder of Coagulation Profile BV as well as coinventor on the thermostable inhibitor of contact activation patent WO2013028069A1. The other authors declare no conflicts of interest., (Copyright © 2023 International Society on Thrombosis and Haemostasis. Published by Elsevier Inc. All rights reserved.)

Background: Patients with cirrhosis have a normal to increased thrombin generation (TG) capacity in platelet-poor plasma (PPP). By reflecting the contribution of all circulating blood cells, whole blood (WB) TG may allow a more physiological assessment of coagulation., Objectives: We compared WB-TG vs PPP-TG in patients with cirrhosis., Methods: Assessment of coagulation included routine tests, factor VIII, natural anticoagulants, PPP-TG, and WB-TG. TG assays were performed with and without thrombomodulin. Twenty-five healthy subjects were included as controls., Results: We included 108 patients (Child-Pugh A/B/C, 44/24/40). Compared with controls, patients had significantly lower platelet count, longer international normalized ratio, higher FVIII, and lower levels of protein C/S and antithrombin. Regarding thrombomodulin-modified TG assays, in compensated cirrhosis, both PPP-TG and WB-TG indicated an increased TG capacity, as reflected by an endogenous thrombin potential (ETP) significantly higher than controls. In contrast, in decompensated cirrhosis, PPP-TG indicated a hypercoagulable state with increased ETP, higher peak height, and shorter time-to-peak than controls, whereas WB-TG revealed a progressive impairment of TG kinetics and total capacity, ultimately resulting in a profound hypocoagulable state in patients with Child-Pugh C cirrhosis (ie, significant prolongation of lag time and time-to-peak with reduction of both ETP and peak height). In decompensated patients, bacterial infections and severity of anemia were associated with a further reduction of both ETP and peak height., Conclusion: Compensated cirrhosis is associated with an increased TG capacity. In decompensated cirrhosis, contrary to PPP-TG, which indicates hypercoagulability, WB-TG shows a significant hypocoagulable state. The clinical value of these findings deserves further investigation., Competing Interests: Declaration of competing interests There are no competing interests to disclose., (Copyright © 2023 International Society on Thrombosis and Haemostasis. Published by Elsevier Inc. All rights reserved.)

Red blood cells (RBCs) and platelets contribute to the coagulation capacity in bleeding and thrombotic disorders. The thrombin generation (TG) process is considered to reflect the interactions between plasma coagulation and the various blood cells. Using a new high-throughput method capturing the complete TG curve, we were able to compare TG in whole blood and autologous platelet-rich and platelet-poor plasma to redefine the blood cell contributions to the clotting process. We report a faster and initially higher generation of thrombin and shorter coagulation time in whole blood than in platelet-rich plasma upon low concentrations of coagulant triggers, including tissue factor, Russell viper venom factor X, factor Xa, factor XIa, and thrombin. The TG was accelerated with increased hematocrit and delayed after prior treatment of RBC with phosphatidylserine-blocking annexin A5. RBC treatment with ionomycin increased phosphatidylserine exposure, confirmed by flow cytometry, and increased the TG process. In reconstituted blood samples, the prior selective blockage of phosphatidylserine on RBC with annexin A5 enhanced glycoprotein VI-induced platelet procoagulant activity. For patients with anemia or erythrocytosis, cluster analysis revealed high or low whole-blood TG profiles in specific cases of anemia. The TG profiles lowered upon annexin A5 addition in the presence of RBCs and thus were determined by the extent of phosphatidylserine exposure of blood cells. Profiles for patients with polycythemia vera undergoing treatment were similar to that of control subjects. We concluded that RBC and platelets, in a phosphatidylserine-dependent way, contribute to the TG process. Determination of the whole-blood hypo- or hyper-coagulant activity may help to characterize a bleeding or thrombosis risk., (© 2023 by The American Society of Hematology. Licensed under Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International (CC BY-NC-ND 4.0), permitting only noncommercial, nonderivative use with attribution. All other rights reserved.)

Organic light-emitting transistors (OLETs) are multifunctional optoelectronic devices that combine in a single structure the advantages of organic light-emitting diodes (OLEDs) and organic field-effect transistors (OFETs). However, low charge mobility and high threshold voltage are critical hurdles to practical OLET implementation. This work reports on the improvements obtained by using polyurethane films as a dielectric layer material in place of the standard poly(methyl methacrylate) (PMMA) in OLET devices. It was found that polyurethane drastically reduces the number of traps in the device, thereby improving electrical and optoelectronic device parameters. In addition, a model was developed to rationalize an anomalous behavior at the pinch-off voltage. Our findings represent a step forward to overcome the limiting factors of OLETs that prevent their use in commercial electronics by providing a simple route for low-bias device operation.

Optical biosensors based on plasmonic sensing schemes combine high sensitivity and selectivity with label-free detection. However, the use of bulky optical components is still hampering the possibility of obtaining miniaturized systems required for analysis in real settings. Here, a fully miniaturized optical biosensor prototype based on plasmonic detection is demonstrated, which enables fast and multiplex sensing of analytes with high- and low molecular weight (80 000 and 582 Da) as quality and safety parameters for milk: a protein (lactoferrin) and an antibiotic (streptomycin). The optical sensor is based on the smart integration of: i) miniaturized organic optoelectronic devices used as light-emitting and light-sensing elements and ii) a functionalized nanostructured plasmonic grating for highly sensitive and specific localized surface plasmon resonance (SPR) detection. The sensor provides quantitative and linear response reaching a limit of detection of 10 -4 refractive index units once it is calibrated by standard solutions. Analyte-specific and rapid (15 min long) immunoassay-based detection is demonstrated for both targets. By using a custom algorithm based on principal-component analysis, a linear dose-response curve is constructed which correlates with a limit of detection (LOD) as low as 3.7 µg mL -1 for lactoferrin, thus assessing that the miniaturized optical biosensor is well-aligned with the chosen reference benchtop SPR method., (© 2023 The Authors. Advanced Materials published by Wiley-VCH GmbH.)

Heterostructures of single- and few-layer black phosphorus (2D bP) functionalized with gold nanoparticles (Au NPs) have been recently reported in the literature, exploiting their intriguing properties and biocompatibility for catalytic, therapeutical and diagnostic applications. However, a deeper insight on the structural and electronic properties at the interface of the 2D bP/Au NP heterostructure is still lacking. In this work, 2D bP is functionalized with Au nanoparticles (NPs) through in situ deposition-precipitation heterogeneous reaction. The smallest realized Au NPs have a diameter around 10 nm as revealed by atomic-force and scanning electron microscopy, and are partially positively charged as revealed by X-ray Photoelectron Spectroscopy (XPS). XPS, UV-vis and Raman spectroscopy, supported by density functional theory (DFT) calculations, confirmed that while the structural and electronic properties of 2D bP are overall preserved, a soft-pairing between P atoms at the surface of 2D bP and Au atoms at the surface of Au NPs occurs, leading to a partial charge transfer at the 2D bP/Au interface, with a positive charge being localized on the Au atoms directly bonded to 2D bP. DFT calculations also predicted a band gap lowering, by 0.8 eV, for phosphorene functionalized with a tetranuclear Au cluster. Larger effects are expected as the Au cluster nuclearity (and coverage) increases.

Bidimensional (2D) materials are nowadays being developed as outstanding candidates for electronic and optoelectronic components and devices. Targeted applications include sensing, energy conversion, and storage. Phosphorene is one of the most promising systems in this context, but its high reactivity under atmospheric conditions and its small-area/lab-scale deposition techniques have hampered the introduction of this material in real-world applications so far. However, phosphorene oxides in the form of low-dimensional structures (2D PO x ) should behave as an electroresponsive material according to recent theoretical studies. In the present work, we introduce electrospraying for the deposition of stoichiometric and large-area 2D PO x nanoflakes starting from a suspension of liquid-phase-exfoliated phosphorene. We obtained 2D PO x nanostructures with a mean surface area two orders of magnitude larger than phosphorene structures obtained with standard mechanical and liquid exfoliation techniques. X-ray spectroscopy and high-resolution electron microscopy confirmed the P 2 O 5 -like crystallographic structure of the electrosprayed flakes. Finally, we experimentally demonstrated for the first time the electromechanical responsivity of the 2D P 2 O 5 nanoflakes, through piezoresponse force microscopy (PFM). This work sheds light on the possible implementation of phosphorus oxide-based 2D nanomaterials in the value chain of fabrication and engineering of devices, which might be easily scaled up for energy-harvesting/conversion applications., Competing Interests: The authors declare no competing financial interest., (© 2021 American Chemical Society.)

Many displays involve the use of color conversion layers. QDs are attractive candidates as color converters because of their easy processability, tuneable optical properties, high photoluminescence quantum yield, and good stability. Here, we show that emissive QDs with narrow emission range can be made in-situ in a polymer matrix, with properties useful for color conversion. This was achieved by blending the blue-emitting pyridine based polymer with a cadmium selenide precursor and baking their films at different temperatures. To achieve efficient color conversion, blend ratio and baking temperature/time were varied. We found that thermal decomposition of the precursor leads to highly emissive QDs whose final size and emission can be controlled using baking temperature/time. The formation of the QDs inside the polymer matrix was confirmed through morphological studies using atomic force microscopy (AFM) and transmission electron microscopy (TEM). Hence, our approach provides a cost-effective route to making highly emissive color converters for multi-color displays.

Organic field-effect transistors (OFETs) are key enabling devices for plastic electronics technology, which has a potentially disruptive impact on a variety of application fields, such as health, safety, and communication. Despite the tremendous advancements in understanding the OFET working mechanisms and device performance, further insights into the complex correlation between the nature of the charge-injecting contacts and the electrical characteristics of devices are still necessary. Here, an in-depth study of the metal-organic interfaces that provides a direct correlation to the performance of OFET devices is reported. The combination of synchrotron X-ray spectroscopy, atomic force microscopy, electron microscopy, and theoretical simulations on two selected electron transport organic semiconductors with tailored chemical structures allows us to gain insights into the nature of the injecting contacts. This multiple analysis repeated at the different stages of contact formation provides a clear picture on the synergy between organic/metal interactions, interfacial morphology, and structural organization of the electrode. The simultaneous synchrotron X-ray experiments and electrical measurements of OFETs in operando uncovers how the nature of the charge-injecting contacts has a direct impact on the injection potential of OFETs.

In the last decade, biochemical sensors have brought a disruptive breakthrough in analytical chemistry and microbiology due the advent of technologically advanced systems conceived to respond to specific applications. From the design of a multitude of different detection modalities, several classes of sensor have been developed over the years. However, to date they have been hardly used in point-of-care or in-field applications, where cost and portability are of primary concern. In the present review we report on the use of nanostructured organic and hybrid compounds in optoelectronic, electrochemical and plasmonic components as constituting elements of miniaturized and easy-to-integrate biochemical sensors. We show how the targeted design, synthesis and nanostructuring of organic and hybrid materials have enabled enormous progress not only in terms of modulation and optimization of the sensor capabilities and performance when used as active materials, but also in the architecture of the detection schemes when used as structural/packing components. With a particular focus on optoelectronic, chemical and plasmonic components for sensing, we highlight that the new concept of having highly-integrated architectures through a system-engineering approach may enable the full expression of the potential of the sensing systems in real-setting applications in terms of fast-response, high sensitivity and multiplexity at low-cost and ease of portability.

Mechanically exfoliated two-dimensional (2D) black phosphorus (bP) is epitaxially terminated by monolayers and multilayers of tetracosane, a linear alkane, to form a weakly interacting van der Waals heterostructure. Atomic force microscopy (AFM) and computational modelling show that epitaxial domains of alkane chains are ordered in parallel lamellae along the principal crystalline axis of bP, and this order is extended over a few layers above the interface. Epitaxial alkane multilayers delay the oxidation of 2D bP in air by 18 hours, in comparison to 1 hour for bare 2D bP, and act as an electrical insulator, as demonstrated using electrostatic force microscopy. The presented heterostructure is a technologically relevant insulator-semiconductor model system that can open the way to the use of 2D bP in micro- and nanoelectronic, optoelectronic and photonic applications.

We studied the chemical-physical nature of interactions involved in the formation of adducts of two-dimensional black phosphorus (2D BP) with organoboron derivatives of a conjugated fluorescent molecule (pyrene). Time-resolved fluorescence spectroscopy showed a stabilization effect of 2D BP on all derivatives, in particular for the adducts endowed with the boronic functionalities. Also, a stronger modulation of the fluorescence decay with oxygen was registered for one of the adducts compared to the corresponding organoboron derivative alone. Nuclear magnetic resonance experiments in suspension and density functional theory simulations confirmed that only noncovalent interactions were involved in the formation of the adducts. The energetic gain in their formation arises from the interaction of P atoms with both C atoms of the pyrene core and the B atom of the boronic functionalities, with a stronger contribution from the ester with respect to the acid one. The interaction results in the lowering of the band gap of 2D BP by around 0.10 eV. Furthermore, we demonstrated through Raman spectroscopy an increased stability toward oxidation in air of 2D BP in the adducts in the solid state (more than 6 months). The modification of the electronic structure at the interface between 2D BP and a conjugated organic molecule through noncovalent stabilizing interactions mediated by the B atom is particularly appealing in view of creating heterojunctions for optoelectronic, photonic, and chemical sensing applications.

Phosphorene, the 2D material derived from black phosphorus, has recently attracted a lot of interest for its properties, suitable for applications in materials science. The physical features and the prominent chemical reactivity on its surface render this nanolayered substrate particularly promising for electrical and optoelectronic applications. In addition, being a new potential ligand for metals, it opens the way for a new role of the inorganic chemistry in the 2D world, with special reference to the field of catalysis. The aim of this review is to summarize the state of the art in this subject and to present our most recent results in the preparation, functionalization, and use of phosphorene and its decorated derivatives. We discuss several key points, which are currently under investigation: the synthesis, the characterization by theoretical calculations, the high pressure behavior of black phosphorus, as well as its decoration with nanoparticles and encapsulation in polymers. Finally, device fabrication and electrical transport measurements are overviewed on the basis of recent literature and the new results collected in our laboratories.

Organic bioelectronics have a huge potential to generate interfaces and devices for the study of brain functions and for the therapy of brain pathologies. In this context, increasing efforts are needed to develop technologies for monitoring and stimulation of nonexcitable brain cells, called astrocytes. Astroglial calcium signaling plays, indeed, a pivotal role in the physiology and pathophysiology of the brain. Here, the use of transparent organic cell stimulating and sensing transistor (O-CST) architecture, fabricated with N,N'-ditridecylperylene-3,4,9,10-tetracarboxylic diimide (P13), to elicit and monitor intracellular calcium concentration ([Ca 2+ ] i ) in primary rat neocortical astrocytes is demonstrated. The transparency of O-CST allows performing calcium imaging experiments, showing that extracellular electrical stimulation of astrocytes induces a drastic increase in [Ca 2+ ] i . Pharmacological studies indicate that transient receptor potential (TRP) superfamily are critical mediators of the [Ca 2+ ] i increase. Experimental and computational analyses show that [Ca 2+ ] i response is enabled by the O-CST device architecture. Noteworthy, the extracellular field application induces a slight but significant increase in the cell volume. Collectively, it is shown that the O-CST is capable of selectively evoking astrocytes [Ca 2+ ] i , paving the way to the development of organic bioelectronic devices as glial interfaces to excite and control physiology of non-neuronal brain cells., (© 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Although it is theoretically expected that all organic semiconductors support ambipolar charge transport, most organic transistors either transport holes or electrons effectively. Single-layer ambipolar organic field-effect transistors enable the investigation of different mechanisms in hole and electron transport in a single device since the device architecture provides a controllable planar pn-junction within the transistor channel. However, a direct comparison of the injection barriers and of the channel conductivities between electrons and holes within the same device cannot be measured by standard electrical characterization. This article introduces a novel approach for determining threshold gate voltages for the onset of the ambipolar regime from the position of the pn-junction observed by photoluminescence electro-modulation (PLEM) microscopy. Indeed, the threshold gate voltage in the ambipolar bias regime considers a vanishing channel length, thus correlating the contact resistance. PLEM microscopy is a valuable tool to directly compare the contact and channel resistances for both carrier types in the same device. The reported results demonstrate that designing the metal/organic-semiconductor interfaces by aligning the bulk metal Fermi levels to the highest occupied molecular orbital or lowest unoccupied molecular orbital levels of the organic semiconductors is a too simplistic approach for optimizing the charge-injection process in organic field-effect devices.