Search

A Point-of-Care system for molecular diagnosis (PoC-MD) is described, combining GaN and CMOS chips. The device is a micro-system for fluorescence measurements, capable of analyzing both intensity and lifetime. It consists of a hybrid micro-structure based on a 32 × 32 matrix addressable GaN microLED array, with square LEDs of 50 µm edge length and 100 µm pitch, with an underneath wire bonded custom chip integrating their drivers and placed face-to-face to an array of 16 × 16 single-photon avalanche diodes (SPADs) CMOS. This approach replaces instrumentation based on lasers, bulky optical components, and discrete electronics with a full hybrid micro-system, enabling measurements on 32 × 32 spots. The reported system is suitable for long lifetime (>10 ns) fluorophores with a limit of detection ~1/4 µM. Proof-of-concept measurements of streptavidin conjugate Qdot™ 605 and Amino PEG Qdot™ 705 are demonstrated, along with the device ability to detect both fluorophores in the same measurement.

MicroLED arrays with the capability of switching each pixel separately with high frequency can serve as structured micro-illumination light engines for applications in sensing, optogenetics, microscopy and many others. We describe a scalable chip process chain for the fabrication of passive-matrix microLED arrays, which were integrated with PCB-based driving electronics. The arrays were produced by deep-etching of conventional planar LED structures on sapphire, followed by filling and planarization steps. The pixel resolution lies in the range of 254 to 2540 pixels-per-inch (ppi), the arrays consist of 32 x 32 pixels. Optical output powers up to 50 µW per pixel were measured. In comparison to CMOS-based approaches, the presented technology is a simplified strategy to produce microLED arrays with high pixel counts.

Digital histogram generation for time-resolved measurements with single-photon avalanche diode (SPAD) sensors requires the storage of many timestamp signals. This work presents a mixed-signal time-to-digital converter (TDC) that uses analog storage to achieve an area-efficient design that can be integrated in large SPAD arrays. Fabricated using a 150 nm CMOS process, the prototype occupies an area of only 18.3 µm × 36.5 µm, a notable size reduction compared to conventional designs. The experimental results demonstrated high performance, with an integral nonlinearity (INL) of 0.35/0.14 least significant bit (LSB) and a differential nonlinearity (DNL) of 0.14/−0.12 LSB. In addition, the proposed TDC can support the construction of histograms comprising up to 512 bins, making it an effective solution to accommodate a wide range of resolution requirements. Validated in a point-of-care (PoC) device for fluorescence lifetime measurements, it distinguished between lifetimes of approximately 4.1 ns, 3.6 ns and 80 ns with the Alexa Fluor (AF) 546 and 568 dyes and Quantum Dot (QD) 705, respectively. The analog storage design and area-efficient architecture offer a novel approach to integrating TDCs in SPAD-based systems, with potential applications in medical diagnostics and beyond.

Gamification is being incorporated into university classrooms due to its educational benefits for students learning, including encouraging student behavior and engagement, and consequently improving learning outcomes. Despite gamification being increasingly used in education, little has been developed related to Very-Large-Scale Integration (VLSI). In this article, we describe two different gamification experiences applied to integrated circuit processing and design in an introductory VLSI design course for Electronic Engineers. While gamification in universities is still not very mature and our experience spans only two academic years, we observed that, with the practice of gamifying part of our course, the topics treated in games were profoundly learned and the experience was very positive in every aspect of the teaching–learning process.

Lensless microscopy requires the simplest possible configuration, as it uses only a light source, the sample and an image sensor. The smallest practical microscope is demonstrated here. In contrast to standard lensless microscopy, the object is located near the lighting source. Raster optical microscopy is applied by using a single-pixel detector and a microdisplay. Maximum resolution relies on reduced LED size and the position of the sample respect the microdisplay. Contrarily to other sort of digital lensless holographic microscopes, light backpropagation is not required to reconstruct the images of the sample. In a mm-high microscope, resolutions down to 800 nm have been demonstrated even when measuring with detectors as large as 138 μm × 138 μm, with field of view given by the display size. Dedicated technology would shorten measuring time.

The recent advances in chip-size microscopy based on optical scanning with spatially resolved nano-illumination light sources are presented. This new straightforward technique takes advantage of the currently achieved miniaturization of LEDs in fully addressable arrays. These nano-LEDs are used to scan the sample with a resolution comparable to the LED sizes, giving rise to chip-sized scanning optical microscopes without mechanical parts or optical accessories. The operation principle and the potential of this new kind of microscope are analyzed through three different implementations of decreasing LED dimensions from 20 µm down to 200 nm.

Recent research into miniaturized illumination sources has prompted the development of alternative microscopy techniques. Although they are still being explored, emerging nano-light-emitting-diode (nano-LED) technologies show promise in approaching the optical resolution limit in a more feasible manner. This work presents the exploration of their capabilities with two different prototypes. In the first version, a resolution of less than 1 µm was shown thanks to a prototype based on an optically downscaled LED using an LED scanning transmission optical microscopy (STOM) technique. This research demonstrates how this technique can be used to improve STOM images by oversampling the acquisition. The second STOM-based microscope was fabricated with a 200 nm GaN LED. This demonstrates the possibilities for the miniaturization of on-chip-based microscopes.

In the Chipscope project funded by the EU, a completely new strategy towards optical microscopy is explored by a team of researchers from different European institutions. In this workshop, the different researchers of the project will explain the last advances obtained in the project, presenting the microscopes, how light emission is produced, and the detection principles and simulations.

We describe the integration of techniques and technologies to develop a Point-of-Care for molecular diagnosis PoC-MD, based on a fluorescence lifetime measurement. Our PoC-MD is a low-cost, simple, fast, and easy-to-use general-purpose platform, aimed at carrying out fast diagnostics test through label detection of a variety of biomarkers. It is based on a 1-D array of 10 ultra-sensitive Single-Photon Avalanche Diode (SPAD) detectors made in a 0.18 μm High-Voltage Complementary Metal Oxide Semiconductor (HV-CMOS) technology. A custom microfluidic polydimethylsiloxane cartridge to insert the sample is straightforwardly positioned on top of the SPAD array without any alignment procedure with the SPAD array. Moreover, the proximity between the sample and the gate-operated SPAD sensor makes unnecessary any lens or optical filters to detect the fluorescence for long lifetime fluorescent dyes, such as quantum dots. Additionally, the use of a low-cost laser diode as pulsed excitation source and a Field-Programmable Gate Array (FPGA) to implement the control and processing electronics, makes the device flexible and easy to adapt to the target label molecule by only changing the laser diode. Using this device, reliable and sensitive real-time proof-of-concept fluorescence lifetime measurement of quantum dot QdotTM 605 streptavidin conjugate is demonstrated.

Fluorescence-based techniques are amongst the most widely used methods in molecular [...]

Initial tests of a building technology for a compact three-dimensional mass producible microrobot are presented. The 3.9 x 3.9 x 3.3 mm3 sized prototype robot represents a microsystem with actuators, sensors, energy management and integrated electronics. The weight of a folded robot is 65 mg and the total volume is less than 23 mm3. The design of the interfaces of the different modules in the robot, as well as the building technology, is described. The modules are assembled using conductive adhesive with industrial surface mounting technology on a thin double-sided flexible printed circuit board. The final shape of the microrobots is achieved by folding the flexible printed circuit board twice. Electrical and mechanical studies are performed to evaluate the assembly and it is concluded that the technology can be used for this type of microsystem. Several issues using the presented assembly technique are identified and addressed. [ABSTRACT FROM AUTHOR]