Search

Thermochromic sensors provide an intuitive and real‐time solution for monitoring the local temperature with naked eyes. Conventional thermochromic sensors often utilize either solution‐type or dense film‐type platforms, which are suboptimal morphologies for exposing a large number of dye molecules to the surface, leading to low sensitivity and sluggish responding speeds. Herein, this article introduces rational synthetic routes to fabricate highly sensitive nanofiber (NF) sensor membranes loaded with thermochromic dyes (C3H6N6·CH2O)x‐loaded nanofibers (NFs) sensor membranes by alignment‐controllable electrospinning techniques (x–y perpendicular and rotary). The NF‐based porous sensor membranes exhibit two‐ to fivefold improved thermochromic sensitivity (ΔRGB) compared to those of dense film‐type sensors at 31.6–42.7 °C. This is attributed to the uniform distribution of dyes throughout the porous NF structure (≈95.7%), which exhibits excellent light transmittance that is 10–30‐fold higher than that of film‐type sensors. Based on the available shape‐conforming synthetic strategies, this article further demonstrates wearable thermochromic sensors in the forms of mask‐, patch‐, and bracelet‐type devices, which can accurately monitor body temperature in real time. [ABSTRACT FROM AUTHOR]

Electrospinning–etching strategy was employed to synthesize Pt-loaded SnO 2 hollow microbelts (Pt_SnO 2 HBLs) based chemiresistive-type sensor demonstrating high sensitivity and selectivity toward acetone gas. This strategy overcomes a major hurdle toward achieving ubiquitous gas diffusion in electrospun structures, and provides highly porous thin-walled HBLs with large surface area and small crystallites. [Display omitted] • In situ templating of SnO 2 with SiO 2 was employed to form Pt-loaded SiO 2 @SnO 2 core–shell microbelts. • Etching away of SiO 2 in the Pt-loaded SiO 2 @SnO 2 microbelts yielded Pt-loaded SnO 2 hollow microbelts. • The Pt-loaded SnO 2 hollow microbelts exhibited good response (R a /R g = 93.5) and selectivity toward 2 ppm acetone at 350 °C. Challenges for ubiquitous diffusion of gas analytes into semiconducting metal oxides (SMOs) based sensing layers have necessitated the introduction of unprecedented synthesis techniques for thin, porous and high-performance gas sensing materials. In this work, electrospinning and calcination were employed to prepare unprecedented SiO 2 –SnO 2 core–shell microbelts (hereinafter referred to as SiO 2 @SnO 2 BLs) followed by etching away of SiO 2 in NaOH solution (pH 12) to achieve hollow SnO 2 BLs (hereinafter referred to as SnO 2 HBLs) with mean crystal size of 14.01 nm, large BET surface area (143.5 m2‧g–1), high porosity (mean pore size of 5.7 nm), and shell thickness of 58.3 ± 11.4 nm. Sensitization of SnO 2 HBLs with apoferritin-templated platinum nanoparticles (Pt NPs) enhanced their detection capability toward acetone. Response (defined as R a /R g , where R a and R g are sensor resistances in air and target gas, respectively) of Pt(0.12 %)_SnO 2 HBLs toward 2 ppm acetone was up to 7.8 times higher compared to that of pristine SnO 2 HBLs, and exhibited faster response (9.2 s). The Pt(0.12 %)_SnO 2 HBLs based sensor indicated a promising long-term stability, and outstanding repeatability of response (R a /R g = 93.7 ± 0.89) toward 25 cycles of 2 ppm acetone exposure in a humid environment of 90 % relative humidity. This performance could be attributed to the unique morphology of HBLs, sensitization effects of catalytic Pt NPs, and enlargement of the electron-depleted layer resulting from a Schottky barrier between Pt NPs and SnO 2 grains. [ABSTRACT FROM AUTHOR]

• Porosity control of nanofibers: The high porosity of the metal oxide nanofibers is the key to achieving the dual sensitization owing to their high gas permeability and numerous active sites. Both saponin and water-ethanol co-solvent play critical roles in modifying morphology of nanofibers into elliptical nanofibers during electrospinning. Additionally, saponin forms numerous pores in the nanofibers when being burnt out during calcination. These porous, elliptical nanofibers possess a larger surface area and porosity.Saponin and water-ethanol co-solvent enabled porous, elliptical nanofibers to emerge. • Bifunctional Ga doping: Ga dopants enhanced sensing performance via conductivity improvement and grain growth inhibition. • Functionalization of Pt catalysts : Spill-over effects and chemical sensitization of remarkably improved C 2 H 2 sensitivity. Herein, we demonstrate a sensitization strategy via solid-solution doping and catalytic metal nanoparticles (NPs) onto porous metal oxide nanofibers (NFs) for superior acetylene (C 2 H 2) sensing capabilities. The introduction of dopants and catalysts not only increases the inherent reactivity of metal oxides, but also induces the spillover of C 2 H 2 onto metal oxides, significantly improving the sensing properties. We elucidate that the high porosity of the metal oxide NFs, prepared by electrospinning and utilizing saponin as a sacrificial template, is the key to achieving high gas permeability and numerous active sites. Consequently, Ga-doped ZnO porous NFs functionalized with Pt catalysts exhibited the highest C 2 H 2 sensing responses among the current state-of-the-art C 2 H 2 sensors (R a /R g = 26.2 at 400 °C) with a fast response time (10.2 s), at a particularly low concentration of 5 ppm. Moreover, these NFs showed excellent selectivity against the interfering gas (H 2 , C 7 H 8 , CO, CH 4 , C 8 H 10 , CH 3 COCH 3 , HCHO and C 2 H 5 OH) and outstanding stability up to 20 sensing cycles to 0.4 ppm of C 2 H 2. These results provide an efficient strategy to tailor composites of metal oxide nanostructures, dopants, and catalysts for highly sensitive gas sensors. [ABSTRACT FROM AUTHOR]

• Synthesis of CA-CNF by insulating block electrospinning & carbonization. • Formation of cross-aligned network even after heat treatment. • Faster reaction kinetics and regular electron pathway of CA-CNF. • High-rate cyclability of CA-CNF (259.4 mAh g−1 at 3000 mA g−1). The conventional use of metallic current collector in an electrochemical cell results in decreased loading of active materials and hence limited capacity in consideration of all the inactive current collector components. In response to this trend, a number of conductive, free-standing materials have been proposed as electrodes, which would act as both current collector and active materials. Here, in this study, we have firstly developed the cross-aligned carbon nanofiber (CA-CNF) for efficient Li storage, especially at high current densities. Using the insulating block electrospinning, the nanofibers can be aligned in a certain direction, where it is viable to fabricate cross-aligned nanofibers in a cost-effective and scalable manner. Attributed to faster kinetics and regular electron pathway arising from CA-CNF, it exhibits an excellent high-rate cyclability (259.4 mAh g−1 at a current density of 3000 mA g−1). This work builds up a milestone in suggesting a cross-aligned carbon nanofibrous network as efficient Li storage, which can also be applied to various electrode materials embedded cross-aligned conductive composite materials. [Display omitted] [ABSTRACT FROM AUTHOR]