Search

• Pioneer Spain: first country to include in grid code the synthetic inertia capability. • Synthetic inertial response of a PV inverter studied based on the Spanish grid code. • Analyzed the role of power plant controller in the dynamic response of the facility. • PV system able to contribute to frequency control providing an inertial response. As the large-scale integration of renewable energy grows, inertia in power systems is reduced, which causes the rate of change of frequency to increase and worsens the frequency nadir during disturbances. There is, therefore, an urgent need to accelerate the development of international standards and regulations that require solar PV systems and other renewable installations to also contribute to stability in the network by emulating inertia. Spain is a pioneer in this field: it is currently the only country that includes the synthetic inertia technical requirement in its grid code. In this context, the present paper analyzes the synthetic inertial response of a PV system model that forms part of an actual PV power plant in Spain under two scenarios, according to its grid code: i) when measurements are conducted at the power conversion PV system level and hence only its control algorithms are executed; and ii) when measurements are conducted at the power plant level and the power plant controller also influences the response of the entire installation. Among its aims, this paper seeks to thoroughly assess the response of an actual PV power conversion system that has the capability of actively contributing to frequency regulation in a network and to critically analyze the suitability of having a power plant controller when the PV facility contributes to power-frequency control by means of an inertial response. The results reveal, at the power conversion PV system level, that the inertia emulation module significantly reduces the response times of the installation to changes in frequency -by more than 68% in the worst case under frequency increases, and by 73% under frequency decreases, thus contributing to more rapid power-frequency regulation in the network. However, at the power plant level, the power plant controller disturbs the PV power conversion system's behavior and causes the opposite effect: response times increase -up to more than 7% in the most unfavorable case when the inertia module is enabled. [ABSTRACT FROM AUTHOR]

This paper proposes the first application of a split-range control technique on a concentrating solar collector to improve an absorption plant production. Solar absorption plants have solar power availability in phase with cooling demand under design conditions. Thus, it is a powerful cooling technology in the context of renewable energy and energy efficiency. These plants need control systems to cope with solar irradiance intermittency, reject irradiation disturbances, manage fossil fuels backup systems and dump closed-loop thermal-hydraulic oscillations. In this work, control techniques are proposed and simulated in an absorption plant in Spain. The plant consists of a concentrating Fresnel solar collector connected to an absorption chiller. The objectives are to operate with 100% renewable solar energy and avoid safety defocus events while reducing temperature oscillations and control actuators effort. Firstly, the current available plant controllers are defined, then two modifications are proposed. The first modification is a split-range controller capable of manipulating both flow and defocus of the Fresnel collector, the second modification is a PI controller to substitute the original chiller on-off controller. The results compare, through validated models, the different control systems and indicate that using both proposed controllers reduces 94% of the sum of actuators effort and 43% of the integral of absolute set-point tracking error compared to the plant's factory pre-set controllers. The suggested controllers increase 66% of energy production and 63% of exergy production. Besides, the split-range technique can be extended to any concentrating solar collector control. [Display omitted] [ABSTRACT FROM AUTHOR]

The operation of solar photovoltaic installations for many years may lead to problems such as reduced energy efficiency and aging of components. Under this framework, replacing certain components in the facility to extend the service life of the power plant is viewed, in some cases, as a feasible strategy. However, despite its enormous strategic interest for the solar PV industry, we find that revamping PV installations has been the focus of very few scientific publications, and even less so when it comes to analyzing real facilities. Thus, this paper performs a techno-economic analysis of three revamping strategies at a real PV power plant located in the south-east of Spain. The strategies consist of substituting, in each case, the PV modules, the inverter, and both components. The simulated results show that the highest production value by installed power is obtained when both the modules and the inverter are replaced. In the same vein, the economic analysis reveals this scenario as the most favorable in terms of profitability. Based on the results obtained, an interesting future line of research would be focused on the extension of the analysis at country level to study the joint impact of numerous revamping actions. • Techno-economic analysis of revamping projects of a real solar PV power plant. • Replacing modules and inverter emerges as the most feasible strategy. • Study's applicability extends to other revamping initiatives and geographical regions. • Economic outcomes allow the most cost-effective alternatives to be determined. • This research can contribute to efficient and sustainable energy planning. [ABSTRACT FROM AUTHOR]

• Energy Communities analysis and review in Europe and, more specifically, in Spain. • Promoting energy poverty reduction and cooperation through Energy Communities. • Real case study focused on reducing energy poverty in the city of Getafe (Spain). • Selection of public buildings to implement energy community in two neighborhoods. • Significant electricity bill reductions for energy poverty households. Advancements in renewable energy technologies, a growing awareness of the need for sustainable energy solutions, and the emergence of new business models in the energy sector, have contributed to the growth of Energy Communities. Public entities can find in energy communities today an opportunity to tackle energy poverty, to increase the cooperation among citizens and to empower them to be a more active player within the energy sector. This paper analyzes energy communities in Europe and focuses specifically on Spain; considering the three beneficial aspects previously mentioned. It aims to obtain ground truth about the applications of these new citizens' arrangements. A citizen-led initiative at the city of Getafe (Madrid, Spain) is included and discussed in detail. This case study focused on reducing energy poverty of its participants. An energy community was designed and implemented as a collective PV solar self-consumption infrastructure. The roofs of various public buildings in the two case study neighborhoods were selected for locating the PV installations. Real metered data were used to evaluate the solution. A public building was selected for the energy community, considering generation on roof and dwellings proximity. The results provided that out of the 77% PV generations could be used to contribute to the demand of 100 residences; while the resulting 23% would provide approximately 60% of the energy demand of the public building. The setting up of the Energy Community not only had the technical part but also included workshops seminars and information sessions, to ensure that people prone to benefit and maximize its impact. [ABSTRACT FROM AUTHOR]

Olive sector residues could contribute to increased use of renewable energies, especially in those areas where the olive crop is produced. This paper determines the maximum amount of electrical and thermal energy which could be obtained in Andalusia from olive sector residues, and the economic value that could be obtained from these energy uses. For this, the current data on installed power and electrical and thermal generation are compared with the calculated potential data which would be obtained at full capacity. The results show there is a 69.23% wastage of olive sector residues for energy purposes. Thus, using the resources at full capacity, 3.9 million tons of biomass per year could be obtained for energy purposes. Currently, only 2 million tons of biomass are used for energy purposes. This wastage translates into a below potential generation of electrical and thermal energy. The full use of these residues would allow 83.9% and 64.9% higher generation of electrical and thermal energy, respectively. The results obtained also show that the economic value of olive sector biomass is higher than the market price value, with the average values for each use being 248.20 €/t for domestic thermal use, 165.04 €/t for electrical use and 139.50 €/t for industrial thermal use. Thus, it is considered feasible that the olive sector biomass could be used to a greater degree than at present. In this sense, it is recommended that more electricity generation plants and thermal-generating systems be put into operation. • There is a 69.2% wastage of olive sector residues that could be used for energy purposes. • The full use of olive by-products would account for 6.2% of renewable electricity. • The full use of olive by-products would account for 26.7% of thermal generation. • Better use of residues would promote the start-up of 55 and 1762 electricity and thermal plants, respectively. • The economic value of olive sector biomass allows the value chain to be covered. [ABSTRACT FROM AUTHOR]