Search

The study attempted to assess the water quality around paper mill effluents discharge areas. Several physicochemical parameters and the Canadian Council of Ministers of the Environment (CCME) Water Quality Index (WQI) were considered to determine the pollution level of surface and groundwater in the selected paper mills areas located in Saidpur, Gobindaganj, and Dupchanchia Upazilas of Bangladesh. Physicochemical characterization of the surface water around the paper mills areas showed that the concentration of EC, TSS, BOD5, COD, phenols, NO3−-N, and K+were exceeded the surface water standard, whereas the DO level ranged from 1.63 to 3.5 were found below the Environmental Conservation Rules (ECR), 1997 standard. Besides, the BOD, COD, and Mn ion concentrations of groundwater exceeded the drinking water standard. In most sampling sites, the WQI of the surface water showed ‘marginal’ category, and the groundwater quality showed 'fair' category. The study observed that the toxic effluents discharged from the paper mills caused harm to the aquatic ecosystem.

This work describes the development of a system that combines a derivatization protocol based on the Katritzky reaction with paper spray ionization mass spectrometry (PSI-MS) for the analysis of amino acid neurotransmitters in mouse brain tissues. The system is relatively simple, consisting of spraying the derivatization solution onto a mouse brain section mounted on a glass slide, applying a small volume of solvent to moisten the sample, pressing a triangular paper onto the sample surface to transfer the sample constituents to the paper surface, and using the paper as a substrate for PSI-MS analysis. The Katritzky reaction facilitated the ionization of the amino acids by reacting a pyrylium salt with the amino group of the analytes, forming very stable pyridinium cations, which greatly increased the sensitivity of the PSI-MS analysis. Most of the intensities of the amino acids modified by the Katritzky reaction were more than 10 times greater than the nonderivatized ones. The system was applied for the analysis of brain sections obtained from mice with Parkinson's disease, and the amino acids gamma-aminobutyric acid (GABA) and glycine (Gly), two compounds very well-known in studies of Parkinson's disease, were readily detected. The results suggest that the Katritzky reaction combined with PSI-MS might offer a significant advance in the knowledge on protocols that improve the sensitivity of detection of crucial biological compounds.

The sorption properties of organomineral composite sorbents have been investigated by ICP-MS method. The diatomite of the Jradzor deposit and bentonite of the Sarigyuh deposit (Armenia) were used as inorganic constituents. Diatomite serves as a structure-forming component and provides mass transfer due to its high porosity (V = 2.0 cm3/g) and large pore sizes (150–200 nm). Bentonite is responsible for the functionality of the sorbents. The organic component is also responsible for the functionality of the obtained sorbents. Paper pretreated with acids (nitric and phosphoric) was used as an organic component. A synthetic solution containing cations of heavy metals was used as an object of study. The experiments were carried out in static mode on a Jar-Test device.

In this study, the removal of UV254, phenol, and calcium from paper industry wastewater by persulfate oxidation was investigated. Fe2+ addition and heat application methods were used for persulfate...

Objectives Paper dust has previously been linked to adverse health effects. However, a comprehensive dataset of paper dust exposures does not appear to have been published previously. Our study was intended to address this need by describing a large dataset of measurements made in Swedish soft tissue paper mills. Methods We compiled personal and area total dust exposure measurements collected from a range of operations by our research staff at four soft tissue paper mills in Sweden. We also compiled measurements made by the occupational health staff at each mill and the Swedish Work Environment Authority. We analyzed these measurements to describe patterns and trends in exposures and used mixed-effects regression models to identify measurement characteristics that predicted exposure levels. Results We compiled 1578 measurements from 1971 to 2009, of which 1026 (65%) were personal samples. Statistically significant differences were found between measurements made by research, mill, and Swedish Work Environment Authority staff, as well as between personal and area measurements. The measurement data suggest that, beginning in the 1980s, exposures declined at three of the four mills, but that overexposures were still common at the end of the period. Papermaking and converting operations had the highest observed dust exposures. One mill had significantly lower exposures than the others. Type of measurement (personal versus area) and source of measurement (research staff, company, or regulatory agency) were not significant predictors of measured total dust exposure after controlling for mill, operation, and time. Conclusions Our analysis of measured paper dust exposures may be useful for historical and contemporary exposure assessment in our own and other epidemiological studies. We have identified specific characteristics (i.e. papermaking operations and mill) and time trends that are important data features to consider, and documented continuing overexposure situations. Our results highlight the ongoing need for application of exposure controls to reduce paper dust exposures in the soft tissue paper industry.

The outbreak of new viral strains promotes advances in universal diagnostic techniques for detecting infectious diseases with unknown viral sequence. Long double-stranded RNA (dsRNA), a hallmark of infections, serves as a virus marker for prompt detection of viruses with unknown genomes. Here, we report on-chip paper electrophoresis for ultrafast screening of infectious diseases. Negatively charged RNAs pass through the micro and nanoscale pores of cellulose in order of size under an external electric field applied to the paper microfluidic channel. Quantitative separation of long dsRNA mimicking poly I:C was analyzed from 1.67 to 33 ng·μL−1, which is close to the viral dsRNA concentration in infected cells. This paper-based capillary electrophoresis chip (paper CE chip) can provide a new diagnostic platform for ultrafast viral disease detection at the point-of-care (POC) level.

Polymeric felts are commonly used in the papermaking process on the paper machine wet end, in the press section, and in the dryer section. They provide an important function during paper manufacturing, including as a carrier or support; as a filter media assisting with water removal on the paper machine; in retention of fibers, fines, and fillers; and in some applications, such as tissue and towel, to impart key structural features to the web. These felts can have highly interwoven complex internal structures comprised of machine direction and cross-machine direction yarns of varying sizes and chemical compositions. Here, we present a non-intrusive three-dimensional (3D) image visualization method using advanced X-ray computed tomography (XRCT). This method was used to characterize the complex 3D felt structure and determine the water removal characteristics of some commonly used paper machine felts. The structural features analyzed include porosity; specific pore-yarn interfacial surface area; 3D pore size distribution; 3D fiber or yarn-size distribution; and their variations through the thickness direction. The top, middle, and bottom layers of the felt have very different structures to assist with water removal and impart paper properties. The size distribution of the yarns, as well as the pores in the different layers of the felt, are also inherently different. These structural features were non-intrusively quantified. In addition, variation in the structural characteristics through the thickness of the felts and its potential role in papermaking is explored. In addition to the 3D structural characteristics, permeability characteristics and water removal characteristics, including rewetting of select felt samples, have also been experimentally determined. It is interesting to observe the relationship between key structural features and permeability and water removal characteristics. These relationships can provide additional insights into press felt design, as well as ways to improve product properties and the dewatering efficiency and productivity of the paper machine.

Sandwich-structured nanocomposites have the potential to improve the mechanical and electrical properties of materials simultaneously. Nanofibrillated cellulose (NFC) modified paper sheet (denominated as N) and softwood paper sheet (denominated as P) are used to prepare insulating paper. Different kinds of insulating paper with the structures of PPP, NNN, NPN and PNP are prepared. Tensile strength, DC conductivity, dielectric response, space charge and breakdown strength are measured. The activation energies of prepared materials are calculated through DC conductivity at 30, 50, 70, and 90 °C. The mechanism for sandwich structure regulating the mechanical and breakdown properties of insulating paper is discussed. Oil impregnated N/P/N paper has a remarkable improvement on tensile strength, conductivity, and DC breakdown strength, which provides a promising scheme to obtain the insulating paper with outstanding tensile and breakdown strength.

Rice straw waste is a lignocellulosic waste produced by farmers in large quantities. In this study, regenerated cellulose (RC) from rice straw was prepared by dissolving rice straw holocellulose (HC) in NaOH/Urea/Thiourea/Water solution by the freeze-thawing process. The crystallinity index of RC was calculated at 31%, which is out of the crystallinity range of 39%–69% that has been previously suggested. The study indicated that the RC is amorphous with a low degree of polymerization (638) and higher hydroxyl group content as compared to HC. The fiber length of RC was found to be 26.7% shorter; however, the width of RC was 21.2% higher as compared to HC. Reduced kinked fiber content was observed in the fraction of RC (18.3%) as compared with HC (39.1%), and a higher curl index of fiber was observed more so in HC (10.5%) than RC (5.6%). Because of the regeneration process, the fiber length was reduced and a fines element content of about 96% was observed in RC compared to the initial fines content of HC (56.9%). Irrespective of the high fines element content of RC, the composite paper of rice straw bleached pulp and RC fibers was developed with an increase in the tensile index from 41.4 N.m/g to 71.2 N.m/g and an increase in the burst index from 4.7 kPa.m2/g to 5.3 kPa.m2/g with the addition of 5% and 15% RC, respectively. However, enhanced tear index of paper was observed up to 5% and then it declined upon further addition of RC. The study revealed that regenerated cellulose can be used as a strength additive to overcome the shortcomings of low mechanical properties in paper products.

Cardiac arrhythmias are a major cause of death and disability. A large number of experimental cell and animal models have been developed to study arrhythmogenic diseases. These models have provided important insights into the underlying arrhythmia mechanisms and translational options for their therapeutic management. This position paper from the ESC Working Group on Cardiac Cellular Electrophysiology provides an overview of (i) currently available in vitro, ex vivo, and in vivo electrophysiological research methodologies, (ii) the most commonly used experimental (cellular and animal) models for cardiac arrhythmias including relevant species differences, (iii) the use of human cardiac tissue, induced pluripotent stem cell (hiPSC)-derived and in silico models to study cardiac arrhythmias, and (iv) the availability, relevance, limitations, and opportunities of these cellular and animal models to recapitulate specific acquired and inherited arrhythmogenic diseases, including atrial fibrillation, heart failure, cardiomyopathy, myocarditis, sinus node, and conduction disorders and channelopathies. By promoting a better understanding of these models and their limitations, this position paper aims to improve the quality of basic research in cardiac electrophysiology, with the ultimate goal to facilitate the clinical translation and application of basic electrophysiological research findings on arrhythmia mechanisms and therapies.

An approach of green in situ synthesis single-step method was applied to produce antibacterial paper. The objective was to investigate the effect of precursor addition on the formation of zinc oxide particles using an in situ single-step method. Zinc chloride concentrations of 0.1, 0.3, 0.5, and 0.7 M were prepared and added into a solution of algae extract and bamboo pulp. The prepared pulps were tested and made into handsheets using a papermaking machine based on TAPPI T205 (2006). Morphological observation of treated papers was conducted using a field emission scanning electron microscope (FESEM). An average of 400 to 570 nm zinc oxide spherical-shaped particle was observed on the fibers of paper. The percentage of element composition of the treated paper were 15.08% to 34.08% of zinc and 17.45% to 32.59% of oxygen captured via scanning electron microscopy with energy dispersive X-ray (SEM-EDX) analysis. The crystallinity test was performed using X-ray dispersion (XRD). A higher percentage of precursors exhibited a more amorphous structure. A measurement of more than 30% increment of inhibition zone was obtained from 10.00 to 25.00 mm against S. aureus, S. choleraesuis, and E. coli. Precursors addition of more than 0.3 M would have the most potential to enhance the growth of zinc oxide via in situ preparation, hence providing better antibacterial properties of the prepared papers.

In this work, we fabricated a novel origami paper-based analytical device (oPAD) assisted by the nanostructuring effect of in situ Pd decoration of Cu/Co-doped CeO2 (CuCo-CeO2-Pd) nanospheres, functionalized with their strongly enhanced electrocatalytic properties to realize an electrochemical and visual signal readout system in oPAD, for highly sensitive detection of amyloid-β (Aβ). The CuCo-CeO2-Pd nanospheres were introduced as an enhanced "signal transducer layer" on account of the electron transfer acceleration caused by catalyzing glucose to produce H2O2 for differential pulse voltammetry signal readout and further 3,3'5,5'-tetramethylbenzidine (TMB) oxidation for colorimetric analysis. Meanwhile, for achieving superior performance of the proposed oPAD, in situ growth of urchin-like gold nanoparticles (Au NPs) onto cellulose fibers was adopted to improve "the recognition layer" in favor of immobilizing antibodies for targeting Aβ through specific antigen-antibody interactions. Combined with the delicate design of oPAD, exhibiting actuation of the conversion procedure between hydrophobicity and hydrophilicity on paper tabs in the assay process, the oPAD successfully enabled sensitive diagnosis of Aβ in a linear range from 1.0 pM to 100 nM with a limit of detection of 0.05 pM (S/N = 3) for electrochemical detection, providing a reliable strategy for quantifying the Aβ protein in clinical applications. Ministry of Education (MOE) This work was financially supported by the Science and Technology Projects of University of Jinan (XKY2002), the Natural Science Foundation of Shandong Province (ZR2020MB057), the Singapore Ministry of Education (MOE AcRF Tier 1 RG176/16), the Taishan Scholars Program, the Case-by-Case Project for Top Outstanding Talents of Jinan, and the project of "20 Items of University" of Jinan (2018GXRC001).

The aim of this study was to identify the nature and cause of foxing spots in a historical manuscript. This manuscript was a Holy Quran from the beginning of the Qajar period and the end of the 18th century. Samples were incubated for 14 days and were evaluated for the presence of fungal activity. UV fluorescence photography, micro X-ray fluorescence spectroscopy and Fourier transform infrared spectroscopy were also used to investigate the characteristics and causes of foxing spots. The results showed that there was no fungal activity in the foxing spots of this manuscript. Based on the morphology of the stain in UV fluorescence photography, these foxing stains are of the Bullseye type, usually associated with metal ions. µXRF spectroscopy also showed a high accumulation of iron and copper at the site of these spots. This indicates abiotic foxing in this manuscript. Based on FTIR spectroscopy and peak deconvolution and fitting by Gaussian function, abiotic foxing increases the cellulose oxidation rate. Intensification of cellulose oxidation in foxing stains can be considered as one of the reasons for paper discoloration.

Hypoxia is a nonphysiological oxygen tension which is common in most malignant tumors. Hypoxia stimulates complicated cell signaling networks in cancer cells, e.g., the HIF, PI3K, MAPK, and NFκB pathways. Then, cells release a number of cytokines such as VEGFA to promote the growth of peripheral blood vessels and lead to metastasis. In the current work, understanding of the internal hypoxic environment in solid tumor tissue was attempted by developing a folding paper system. A paper-based solid tumor was constructed by folding a filter paper cultured with cancer cells. The cellular response in each layer could be analyzed by disassembling the folded paper after the culture course. The result showed that an internal hypoxic environment was successfully reproduced in the paper-based solid tumor. The cells in the inner layer expressed high levels of HIF1-α and VEGFA. Hence, proliferation and migration of endothelial cells were shown to be induced by the cells located in the internal hypoxic environment. Moreover, the paper-based solid tumor was transplanted into nude mice for the study of hypoxic response and angiogenesis. The crosstalk between internal and external parts of solid tumor tissue could be analyzed by sectioning each layer of the paper-based solid tumor. This approach provides a favorable analytical method for the discovery of the interaction between cancer cells, hypoxia, and peripheral angiogenesis.

The latest outbreak of a coronavirus disease in 2019 (COVID‐19) caused by the severe acute respiratory syndrome coronavirus 2 (SARS‐CoV‐2), evolved into a worldwide pandemic with massive effects on health, quality of life, and economy. Given the short period of time since the outbreak, there are several knowledge gaps on the comparative and zoonotic aspects of this new virus. Within the One Health concept, the current EAACI position paper dwells into the current knowledge on SARS‐CoV‐2’s receptors, symptoms, transmission routes for human and animals living in close vicinity to each other, usefulness of animal models to study this disease and management options to avoid intra‐ and interspecies transmission. Similar pandemics might appear unexpectedly and more frequently in the near future due to climate change, consumption of exotic foods and drinks, globe‐trotter travel possibilities, the growing world population, the decreasing production space, declining room for wildlife and free‐ranging animals, and the changed lifestyle including living very close to animals. Therefore, both the society and the health authorities need to be aware and well prepared for similar future situations, and research needs to focus on prevention and fast development of treatment options (medications, vaccines).

Environmental and health concerns are driving food packaging to reduce the use of poly- or perfluorinated compounds and petroleum-based polymers. Here, we successfully obtained good oil-proof paper by combining cellulose nanofibril (CNF) film with filter paper through film transfer. The process was not only facile but also did not require chemical reagents other than water. To achieve the kit number 12, the basis weight of the CNF film was 2.1 g/m2, which was much less than the amount required for coating. The calendering process further reduced the pores thus improving the oil resistance of the film transfer paper. At a calendering pressure of 20 N/mm, only 1.4 g/m2 of the CNF film was required for kit number 12. This study provides a new way for the application of CNF in the field of oil resistance.

As the most frequently used archival materials for painting and recording, paper lays the groundwork for the development of prosperous human civilization. However, its susceptibility to three primary factors including external ultraviolet light, increased acidity, and biological pathogens in long-term storage shortens the longevity of paper. Therefore, the protection of paper-based cultural relics is extremely urgent. Inspired by the three adverse factors affecting the protection of cultural relics, we herein propose to combine the ultraviolet absorber 2-hydroxy-4-(octyloxy)benzophenone (UV-531) and alkaline zinc oxide (ZnO) nanoparticles innovatively into the antibacterial agent polyhexamethylene biguanidine hydrochloride (PHMB) to realize the strategy of three birds with one stone for relics protection. This study illustrates that the tensile strength and the folding endurance of different test papers are guaranteed by coating them with the composite reagents, and molds including Mucor, Trichoderma, and Aspergillus niger are effectually sterilized. In addition, a hand-painted Chinese ink-wash painting with beautiful flowers is chosen as the object for simulating cultural relics protection, and negligible color fading is observed in aging experiments. From the perspective of effectiveness, simplicity, and economy, this strategy sheds light on preservative protection of paper-based relics in long-term storage.

We demonstrated the thermally robust reduced graphene oxide (rGO)/boron nitride nanotube (BNNT) papers and their application in electromagnetic interference shielding. In order to overcome the thermal durability shortcomings of electromagnetic wave shielding paper based on rGO nanomaterial, rGO/BNNT electromagnetic interference (EMI) shielding paper having excellent thermal durability could be manufactured using BNNT nanomaterials having excellent chemical and thermal stability at high temperature. With the addition of a little BNNT, the durability against temperature can be increased by more than two times while there is little reduction in EMI performance.

Paper-based photodetectors have attracted extensive research interest owing to their environmentally friendly and highly deformable properties. Although perovskite crystals with outstanding optoelectronic properties have proved to be one of the most promising candidates for photodetectors, the development of paper-based photodetectors is hindered by the moisture absorptivity of paper and the instability of perovskite crystals in a humid atmosphere. In this study, we demonstrate a highly deformable and high-performance paper-based perovskite photodetector. The photodetector maintains its excellent performance even after exposure to a relative humidity of 60% for 120 h.

Commercial Chinese ink was employed to disperse pristine vapor-grown carbon nanofibers (VGCNFs) in aqueous suspensions via horizontal ball milling. The obtained suspension was used to fabricate conductive paper-based composites through filtration-deposition onto filter paper. It was found that the carbon black particles from the Chinese ink helped separate VGCNFs and acted as connection points between the VGCNFs, while the glue reinforced the conduction network. Thus, the VGCNF-ink/paper ternary composite showed sufficiently low sheet resistance. With merely 2.5 mg·cm−2 VGCNFs, the sheet resistance could be reduced to 4.5 Ω·sq−1. As a proof of concept, these paper-based composites were directly used as electrodes of solid-state symmetric electronic double-layer capacitors (EDLCs) and the substrate for the electrodeposition of MnO2 to achieve higher electrochemical performances. The EDLCs fabricated with 2.5 mg·cm−2 VGCNFs showed a specific capacitance of 224 mF·cm−2 at a current density of 1 mA·cm−2, which was retained by 86.4% after 10,000 charge-discharge cycles. Moreover, thanks to the high electrical conductivity and the porous structure, the MnO2 decorated paper-based composites exhibited dramatically enhanced specific capacitance. It is believed that our finding offers an idea to directly utilize commercial Chinese ink for the fabrication of electrode materials.

Objective The objective of this study was to develop the first edition of a Chinese evidence-based position paper on the management of oral leukoplakia (OLK). Study Design The consultant group for drafting the position paper consisted of 31 oral medicine specialists and 2 evidence-based medicine specialists. English studies (searched in PubMed, EMBASE, and the Cochrane Library) and Chinese studies (searched in China National Knowledge Infrastructure and WanFang) published before January 2018 were used. The quality of the study was assessed using the Grading of Recommendations Assessment, Development, and Evaluation grid, and the strength of the recommendations was determined based on the results of 3 rounds of voting among the consultant group members using the Delphi method. Results Twenty-two evidence-based guidelines for clinical management and monitoring of OLK were established in this position paper. A clinical path diagram for oral health practitioners was constructed based on the recommendations. Conclusion Current evidence suggests that management and monitoring of patients with OLK should be performed by experienced clinicians to control the lesion and for early detection of malignant transformation. However, all recommendations are based on evidence of low or extremely low quality and may require further modification as new evidence is produced.

More than 50 billion disposable paper cups used for cold and hot beverages are sold within the United States each year. Most of the cups are coated with a thin layer of plastic — low density polyethylene (LDPE) — to prevent leaking and staining. While the paper in these cups is both recyclable and compostable, the LDPE coating is neither. In recycling a paper cup, the paper is separated from the plastic lining. The paper is sent to be recycled and the plastic lining is typically sent to landfill. In an industrial composting environment, the paper and lining can be composted together if the lining is made from compostable materials. Coating paper cups with a compostable performance material uniquely allows for used cups to be processed by either recycling or composting, thus creating multiple pathways for these products to flow through a circular economy. A segment of the paper converting industry frequently uses an extrusion grade of polylactic acid (PLA) for zero-waste venues and for municipalities with ordinances for local composting and food service items. The results among these early adopters reveal process inefficiencies that elevate manufacturing costs while increasing scrap and generally lowering output when using PLA for extrusion coating. NatureWorks and Sung An Machinery (SAM) North America researched the extrusion coating process utilizing the incumbent polymer (LDPE) and PLA. The trademarked Ingeo 1102 is a new, compostable, and bio-based PLA grade that is specifically designed for the extrusion coating process. The research team identified the optimum process parameters for new, dedicated PLA extrusion coating lines. The team also identified changes to existing LDPE extrusion lines that processors can make today to improve output. The key finding is that LDPE and PLA are significantly different polymers and that processing them on the same equipment without modification of systems and/or setpoints can be the root cause of inefficiencies. These polymers each have unique processing requirements with inverse responses. Fine tuning existing systems may improve over-all output for the biopolymer without capital investment, and this study showed an increase in line speed of 130% by making these adjustments. However, the researchers found that highest productivity can be achieved by specifying new systems for PLA. A line speed increase to more than 180% and a reduction in coat weight to 8.6 µm (10.6 g/m2 or 6.5 lb/3000 ft2) was achieved in this study. These results show that Ingeo 1102 could be used as a paper coating beyond cups.

In the tourism industry, the sales of local specialties is an important part, and the package design and integrity of the specialties are very important. This paper first introduced the support vector machine (SVM) algorithm that was used for detecting defects on the surface of paper packages. Then, the design of red wind packages was briefly described, and the simulation experiment was carried out on SVM algorithm using red wine packages with different degrees of surface defects. Proper parameters were tested using the k-fold cross-validation method. The results demonstrated that the properties of paper improved the value of packages and the SVM algorithm had better accuracy than artificial recognition in recognizing different degrees of defects on the surface of packages. In conclusion, this paper describes the application of paper in packages and provides an effective method for the defection of defects on the surface of packages. This study provides an effective references to the improvement of package values and the enhancement of package integrity.

This paper shares lessons learned at the completion of a large multi- year project (2008-2018) to move to a next-generation digital preservation repository at Harvard Library. These final stages included activities running in parallel to migrate the metadata for millions of files, train fifty-five different units to use the new repository tools, and migrate the audio files from obsolete formats. Harvard Library’s digital preservation repository, the Digital Repository Service (DRS), holds over 69 million files and 285 TB of data from across the university. When it first launched in October 2000, it was one of the first digital preservation repositories at an academic institution. At the time it was designed, there were little- to-no digital preservation/digital library standards, best practices or tools to adopt. Planning for a next-generation DRS under the name the “DRS2 project” began in 2008, with the purpose of modernizing the DRS to take advantage of the latest technologies, standards, and practices and to provide curators, depositors, and preservation staff with significantly enhanced tools. The DRS2 project included four different types of migrations: infrastructure, metadata, file format, and repository users. It included such daunting tasks as re-architecting the entire repository; re-parsing all of the millions of files; changing the underlying data model, Archival Information Package (AIP) format, and all of the XML schemas; rewriting all of the repository metadata; retraining all of the repository users; and reformatting all of the audio deliverable files. A repository migration of this size and breadth was unprecedented in the digital preservation community, so there were few preexisting examples to learn from. By sharing the experience of this project, the authors hope that other institutions can benefit from the lessons learned during a repository migration of this magnitude. This paper provides an overview of all four migrations, but delves deepest into the results, challenges and lessons learned from the metadata migration. These lessons are applicable to preservation planning and interventions, future migrations, preventing metadata and content errors, and conducting very large projects in general. This paper was the runner up for the Best Long Paper award.

The role of standards in digital preservation is widely acknowledged. The current version of the ePub standard, used for publishing and disseminating eBooks, is ePub3, specifically 3.1 (January 2017). A marked difference from ePub2 is support for fixed layout files and, whilst several different ePub readers are available, not all have upgraded to provide full support for ePub3. In late 2017 and early 2018 the British Library’s digital preservation team undertook research into the impact of using an ePub viewer without explicit support for ePub3 on a mixed sample of ePub3 files. The sample comprised 54 files: 20 of these were of fixed layout, the remainder utilized reflowable layouts. For the analysis, content was accessed using two different open source ePub readers: Calibre, which has a wide user base but does not currently explicitly support ePub3, and Readium, which does explicitly support ePub3. ePub3 files with a reflowable layout broadly rendered to an acceptable standard using both readers. There was one notable exception for both readers, and investigations indicated this was likely due to a problem with the file itself rather than the rendering software. Problems manifested in a more serious way when using Calibre to access just under half of the fixed layout ePub3 files. The rendering of these items inhibited access to intellectual content for example by overlaying it on other content, misrepresenting it, or not including it at all. Other issues that were initially apparent with the other half of the fixed layout sample were mostly resolved by the simple quick fix of switching from ‘page’ view to ‘flow’ view. By contrast, Readium was able to display all of fixed layout files correctly. The research serves as a reminder that whilst standards remain an essential tool in the digital preservation toolbox, updates to a standard may necessitate changes to the rendering software in use. It further underlines the importance of accurate characterization so that repositories can identify formats at a version level or be able to identify items with explicit rendering needs beyond those served by their default rendering viewers. This paper was the runner up for the Best Short Paper award.

The PREMIS 3.0 Ontology Working Group recognized the need for the preservation community to be able to use Semantic Web tech- nology to leverage systems managing the long-term preservation of digital holdings. Driven by the main principle of adherence to the PREMIS Data Dictionary, and a set of well-established Linked Data principles, the draft release of the PREMIS 3 OWL ontology comes after two years of conceptualization, discussion and experi- mentation. The release of the draft was followed by a public review of the revised ontology soliciting a wider discussion about the con- ceptual choices expressed by the ontology. This article explains how interoperability issues have been addressed, with the intent of maintaining continuity between the PREMIS Data Dictionary and the PREMIS OWL ontology. This paper won the iPres 2018 Best Short Paper Award

Pseudoestrogene bisphenol A (BPA) can be important ingredient of thermochromic inks, increasingly used materials in thermal printing paper, security printing, advertising, design and as temperature indicators in medicine and food industry. BPA mass fraction in thermochromic inks can be up to several percent. Hence, disposal of items with thermochromic prints pose a risk of environmental pollution. In this work BPA mass fraction was monitored during anaerobic degradation of papers with thermochromic prints in soil in both matrices: papers and soil. The degradation conditions simulated deeper layers of waste at a landfill site. Six types of papers with prints of thermochromic ink containing 2% of BPA were subjected to anaerobic degradation over up to 150 days.

In this study, we evaluated the effect of bamboo bleached kraft pulp (BKP) on the strength of the coloring paper used for pear paper bags. The characteristics of bamboo BKP were measured to compare them with those of softwood BKP and hardwood BKP. Handsheets from bamboo and hardwood BKPs were prepared at various mixing ratios, and their strengths were then analyzed. After that, a mill trial was performed to produce a prototype of coloring paper with bamboo BKP, and the effect of bamboo BKP on the strength of the coloring paper was finally determined. The initial freeness and fiber shape of bamboo BKP were similar to those of hardwood BKP, although the average fiber length and curl of bamboo BKP were higher than those of hardwood. As the mixing ratio of bamboo BKP increased, the strength of the handsheets increased, indicating the enhancing effect of bamboo BKP on the strength of coloring paper. As a result of the mill trial of coloring paper in the specialty paper mill, it was found that the tensile strength increased by 27.8% and burst strength by 20.0% when bamboo chemical pulp replaced 20% of the hardwood chemical pulp. Therefore, it was concluded that bamboo chemical pulp can replace and improve the strength of hardwood chemical pulp for manufacturing coloring paper.

The present study reports the characterization of reverse osmosis (RO) technology at water treatment plant Cogen-2 in paper and Board mills, Pakistan. RO is a commonly used process to obtain de-mineralized water for high-pressure boiler operation in thermal power plants. Scaling and fouling in three-stage RO plants is a major challenge in chemical industry due to the use of raw brackish water in the power plant of paper and board mills. In our study, the feed water quality of RO was changed from soft water to raw water to make it economical. The cleaning frequency was increased three times than normal, which was unsafe for operation and it was required to control scaling and fouling to achieve the desired result. Differential pressures behavior of all stages for 2-month data was observed without acid treatment, and the results of Langelier Saturation Index (LSI) control parameters (temperature, pH, total dissolved solids, calcium hardness, and alkalinity) clearly showed the abnormality. To optimize scaling and fouling of RO, the LSI factor was controlled in total reject water for the next 2 months by acid treatment in feed water. Duration of chemical cleaning and membranes’ life has been extended by fouling and scaling control. Understanding the effect of operational parameters in RO membranes is essential in water process engineering due to its broad applications in drinking water, sanitation, seawater, desalination process, wastewater treatment, and boiler feed water operation. The product flow increased from 18.3 to 19.9 m3/h, and this was due to a decrease in the rejection flow from 8.2 to 6.7 m3/h. The total reject stream pressure also increased from 8.1 to 9 bar. A lower value of LSI of 1.6 is obtained in the reject water stream after the acid treatment.

A new type of polydimethylsiloxane-based paper transparentizing agent was prepared via a combined method. The performance of the transparentizing agent was investigated systematically by adding and dipping, with use of the surface sizing device of a paper machine. Optimum performance was found at 30% concentration of the transparentizing agent and 30 to 45 °C of dipping temperature. Under the optimal conditions, the transparentizing t agent achieved a rapid penetration in the base paper and filled in the pores of the paper, to be further effectively adsorbed and retained on the fiber surface. The transparency of test paper reached as high as 76±0.97 %, which was 37±1.4% higher than that of the control. However, the addition of transparentizing agent reduced the mechanical strength of paper slightly. The as-prepared transparentizing agent was found to exhibit excellent application stability and biodegradability when applied in the paper machine，When used as plastic film, the transparent paper would lose its strength completely after eight weeks. The resulting transparent paper can be used to develop paper-based film and other related plant based transparent/ translucent paper, which has great potential in replacing plastic products and eliminating white pollution.

Influence of the thermochemical processing (the cook) conditions and of the milling on characteristic of the waste paper with polyurethan and polyaziridin was studied. The waste paper was reduced to the degree size of the particles 5...8 mm in mill of the dry grind and chemical processing under higher temperature (to 70 °C) by solution, contain sodium persulfate and hydroxide; duty of water 6. Duration of cook varied from 1 to 5 hours, expense of persulfate sodium varied from 2 to 12%, hydroxide sodium – from 0.5 to 3% from mass of the waste-papers. The secondary fiber was obtaining by breaking-up of the pulp in the hydropulper. The dependency of the length and factor of the form of the secondary fiber from conditions cook was absent. The slight width increasing of the fibers with the higher pH of cooking liquor was determined: from 26.5 мкм under pH 3–4 to 29 мкм under pH 8–9. The conjectural reason is swelling of the cell wall. The waste paper milling was executed in the «stream-barrier» machine. The strength properties of the paper correspond with the feature, inherent of the secondary pulp.

Today, the paper industry is faced with a global deficiency of raw wood materials, so alternative sources of virgin cellulose fibres are playing an important role in paper production. Agricultural countries produce large quantities of crop farming by-products such as straw, which is an interesting alternative raw material for cellulose fibres. Straw is used in many industries because of its numerous advantages: animal food industry, biofuel industry, construction industry and as artistic material. The potential use of straw production residues is of great importance in paper and printing industry. The focus of this research is on triticale straw, which was used as a non-wood fibre source for paper production. Namely, triticale straw was converted into semi-chemical pulp and was combined with recycled wood pulp in order to produce alternative laboratory papers. The usability of this kind of laboratory papers in printing industry was analysed based on line reproduction quality. This research evaluated and analysed line reproduction quality based on four line attributes: width, blurriness and raggedness. The results of this research proved that triticale pulp in laboratory papers has equal influence on line printing quality as the recycled wood pulp.

The main thing of Artificial intelligence (AI) is the consummation of natural dialogue between humans and machines. There are numerous IT companies have used the dialogue systems technology to establish various kinds of Virtual assistants grounded on their operations and areas for adding commerce between mortal and machine, similar as Microsoft’s Cortana, Apple’s Siri, Amazon Alexa, Google Assistant. Like Microsoft Cortana we've created our own virtual desktop assistant only for Government College Of Engineering Chandrapur (GCOEC) using python which is suitable to run on any windows operating systems. We use python as a programming language because it has a multitude of libraries which can be used to create Artificial Intelligence. Our version of desktop assistant is capable of recognizing voice and voice commands. Desktop Assistant are programs on digital device like PC that hear and respond to verbal commands. Example, a user can say, “Open GCOEC Website” and the assistant will answer with the sanctioned website of GCOEC. Desktop Assistants can change the way of life of the people in a different manner. Bias is starting to build up in the community as AI’s are getting smarter in their own way to interact with humans in an easy language. The Desktop Assistant is a program that can fete mortal voices and can respond via integrated voice system. This paper will define the working of Desktop assistant, their main problems and limitations. In this paper it's described that the system of creating a Desktop assistant without using pall services, which will allow the expansion of similar bias in the future

Artificial intelligence (AI) has revolutionized various industries, and its impact on the job market is significant. While AI has the potential to automate repetitive and time-consuming tasks, it also presents new job opportunities that require expertise in data analysis, software engineering, and machine learning. The paper provides an overview of the current state of the job market and the challenges it faces, and explains how AI is transforming the job market, including its impact on job creation and destruction, skill requirements, and wage distribution. The paper analyzes the job market trends from 2019 to 2023 based on the latest research and reports, and discusses the implications of AI for the workforce and policymakers. The paper concludes with some recommendations for future research and policy interventions. It discusses the benefits of AI, such as increased productivity, efficiency, and accuracy, and highlights the challenges that AI poses, including the displacement of certain jobs and the need for retraining workers. The review paper also discusses how AI is impacting workplace safety and health, including both the potential benefits and the new hazards that AI presents. Finally, the review paper explores the policies and regulations needed to ensure that AI is used ethically and responsibly in the job market. Overall, this review paper aims to provide a comprehensive understanding of the impact of AI on the job market and its implications for workers, businesses, and society

Human-Computer Interaction (HCI) plays a crucial role in shaping our digital experiences, with professionals at the forefront of designing and developing interactive systems. This review paper examines the professional issues within HCI, aiming to identify key challenges, trends, and advancements in the field. Through an extensive analysis of existing literature, this paper explores various dimensions of professional issues in HCI, including ethical considerations, user-centered design practices, socio-cultural implications, legal aspects, and the impact of emerging technologies on HCI professionals. By synthesizing research findings and critical insights, this review highlights the importance of addressing these issues for the advancement of HCI. Furthermore, it presents a comprehensive overview of the current state of research, identifies gaps and limitations, and proposes future directions for research and practice in order to foster a more ethical, inclusive, and effective human-computer interaction domain. This review contributes to the understanding of professional challenges faced by HCI practitioners and provides a foundation for informed discussions and developments in this dynamic field.

The usage of vegetal fibers coming from the wood of planted forests as a source of cellulose for paper production, has placed Brazil in a prominent position in the worldwide economic scenario, being that one of the best alternatives of value aggregation to this natural material. This research has evaluated the potential of three woody species of occurrence in the Cerrado, a Brazilian Biome, as a source of alternative raw material to alien species, nowadays widely used in Brazil for the pulp and paper industry. Wood radial samples of Cedrela fissilis, Cecropia sp. and Genipa americana with 12 years of age were collected in a peri-urban are of the city of Goiânia, through the non-destructive method, for the study on fiber’s morphology and basic density. With the data obtained it was possible to determine the felting index, coefficient of flexibility, wall fraction and Runkel index, for fibers qualitative evaluation. The careful evaluation of the results – and the detailed comparison with other species – made it possible to affirm that only the wood of Cedrela fissilis and Cecropia sp. had had potential for the proposed objective. Therefore, relevant aspects for the complementation of this research are pointed.

Paper and garden waste is one of the types of waste that can be found in big cities in Indonesia, one of which is Depok City. Garbage collectors can recycle not all paper waste into new products. In addition, garden waste is also garbage, one of the wastes found produced every day from gardening activities. This study aimed to analyze the potential for reducing the use of paper and garden waste to be used as RDF in Depok City. This study analyzes the quality of RDF based on the parameters of water content, ash content, density, and calorific value resulting from the material substitution. The results were analyzed using the multicollinearity method and the Kepner-Tregoe Decision Analysis (KTDA). The results of the multicollinearity test show that the ash content and water content can reduce the calorific value of RDF mixed with paper and garden waste. The addition of garden waste composition can increase the calorific value. Based on the results of decision analysis using KTDA, it shows that the variation of the mixture of 75% paper waste and 25% wood waste has the largest points compared to other variations. Material Flow Analysis (MFA) utilization of this waste can reduce the generation of paper waste and garden waste by 3.5% and 12.3%, respectively.

The migration of photoinitiators (PIs): benzophenone (BP), ethyl 4-dimethylaminobenzoate (EDAB), and 4-chlorobenzophenone (CBP), from polyethylene (PE)-coated paper to 4% (v/v) acetic acid and 10% (v/v) salt-simulated food solution was quantitatively analyzed using gas chromatography–mass spectrometry. The migration behavior of the three PIs was studied under three specific working conditions: conventional heating, microwave power, and random vibration level. The migration rate of the three PIs in acidic food simulants was ranked from BP > EDAB > CBP under the specific working conditions. The mobility of the three PIs increased with increasing temperature, microwave power, and random vibration acceleration in 4% (v/v) acetic acid by 10, 10, and 15%, respectively. The experimental migration data of three PIs in PE-coated paper under different temperatures and microwave powers were used to establish the Crank monolayer migration model according to Fick’s second law. The diffusion coefficient D increased with an increase in experimental conditions. According to the migration data under the condition of random vibration level, a mathematical model conforming to the Fick model was established, fitting the migration process. These results showed that conventional heating, microwave heating, and vibration could affect the food safety of PE-coated paper.

The use of templates and examples of papers separately is proven to be able to develop students' writing skills. The average degree of mastery that can be achieved is already in the good category. Using various learning facilities can be a solution to improve these achievements into a very good category. This study aims to analyze the effectiveness of implementing templates and sample papers in developing students' writing skills in science courses. The pre-experimental research was conducted on elementary school teacher education study program students. Data on each student's scientific research paper writing skills were collected using the documentation method. This data was then analyzed descriptively. The descriptive analysis includes average and proportion measurements. Based on the results of data analysis, it was found that the average student's skills in writing papers were in a good category. Most students have very good (41.44%) and good (40.54%) categories of writing skills. 13 indicators have reached the very good category, one indicator is in a good category, and two indicators are in the sufficient category. The rests are one indicator still in the less category and four indicators in the less category. The conclusion that can be drawn from this research results is using examples and paper templates as effective learning facilities to improve students' writing skills.

The limited supply of wood as a raw material in various industries requires a better alternative material. Wasted-based composite engineering can be a solution to this problem. What's more, composite can be engineered according to needs, such as having the ability to reduce heat to maintain comfortable room temperature conditions. Therefore, in this research, a particle board reinforced by pineapple leaf fiber waste and HVS paper waste was developed to know the effect of the particle board reinforcement composition on reducing heat. In this research, a comparison of pineapple leaf fiber waste and HVS paper waste was used at 100%:0%; 70%:30%; 50%:50%; 30%:70%; and 0%:100% with resin adhesive. This particle board is made by mixing all the ingredients and then printing it into a mold and then carrying out the drying process. The test was carried out based on a temperature difference analysis. The most optimum particle board reinforcement composition to reduce heat is 100% pineapple leaf fiber waste : 0% HVS paper waste.

We develop a vision system for batch inspection by oven white paper model color by manufacturing a machine vision system for the oven manufacturing automation process. In the vision system, white paper object detection (spring), color clustering, and histogram extraction are performed. In addition, for the automated process of home appliances, we intend to develop an automatic mold combination detection algorithm that inspects the label position and direction (angle/coordinate) using deep learning.

The purpose of this study is to provide an overview of quality control in the paper industry.Wood preparation, pulping, bleaching, and papermaking are all steps in the papermaking process, and eachone presents its own set of quality control challenges. The study looks at the various methods that are usedin the industry to monitor and control the quality of finished paper products. It includes laboratory testing,statistical process control, and online monitoring systems, as well as traditional and modern quality controltechniques. The study also emphasizes the significance of quality control in the paper industry, which canhave a significant impact on product performance, customer satisfaction, and profitability. Finally, the studyconcludes with a discussion of benefits in the paper industry's quality control.

In the research, different experimental setups were used to examine the treatment of wastewater from the paper industry using the electrooxidation method, one of the electrochemical treatment methods in the batch system. In the 2000 mL volume jacketed glass reactor utilized for the treatment of wastewater from the paper industry, 4 anode and 4 cathode sieve type plates of 7 cm x 10 cm dimensions were positioned at 0.5 cm intervals, and 1200 mL wastewater was used in the tests. Coated sieve type Ti/Pt electrodes were employed as the anode in the electrooxidation studies, and uncoated sieve type Ti electrodes were used as the cathode. It was determined that the active anodic wet surface area was 1078 cm2 . The removal rates of pollutant parameters such as turbidity and SS (Suspended Solids) in the experiments; the effects of wastewater initial pH value and supporting electrolyte type parameters were investigated. According to the results, the most effective pH value for Ti/Pt anode type at 400 rpm mixing speed was determined to be waste water natural pH (7.5), and 0.50 M NaCl was the most successful supporting electrolyte type. 96.92% Suspended Solids removal efficiency and 95.38% turbidity removal efficiency for Ti/Pt anode were achieved under ideal conditions. In addition, 312.05 kW-hour/kg COD is determined as the energy consumption value.

This study addresses the barriers that hinder paper recycling and explores potential solutions to overcome these challenges. The barriers discussed include a lack of recycling infrastructure, inadequate education and outreach, cultural attitudes towards waste, and a lack of economic incentives. To address these barriers, governments and organizations can implement solutions such as expanding recycling infrastructure, improving education and outreach, addressing cultural attitudes through targeted messaging, and providing economic incentives. Successful implementations of these solutions in other locations or industries are also highlighted. The study emphasizes the importance of addressing these barriers to increase paper recycling rates and reduce the environmental and economic costs of low recycling rates.

Change has become the norm and with the digital revolution we are seeing the demise of the printed word. Dentistry is a pictorial subject, but will pictures in a textbook or journal be surpassed by accessing digital ones on a screen? This article reviews the rapidly changing access and reading of dental publications. An argument is that the ease of access to electronic material, such as video and podcasts, may make traditional paper-based publications obsolete. Already dentistry is seeing such changes take place. With such revolutions come challenges. Misinformation is much easier to generate, and the evidence base may be diluted. Furthermore artificial intelligence is now able to produce text and papers that will make it more difficult to critically review the dental content on offer. The future will bring many challenges and this article provides an opinion on what dentistry might expect. CPD/Clinical Relevance: There are challenges posed by the increasing use of digital resources for information and how this might impact dental knowledge.

The performance of lean duplex stainless steels has been utilized by the pulp and paper industry since their introduction to the market almost 20 years ago. Experience has shown that this group of stainless steels has exceptional performance in, for example, alkaline environments towards typical deterioration mechanisms, i.e., uniform corrosion and stress corrosion cracking. The chemistry of the “lean” duplex steels is designed so that the content of volatile and expensive elements like nickel and molybdenum can be reduced to an absolute minimum without sacrificing the technical performance. This reduces the raw material cost and most importantly provides predictability of the steel price, which is often challenging with conventional austenitic and duplex stainless steels.Thanks to a dual phase microstructure and high nitrogen content, lean duplex steels have at least two times higher strength compared to standard austenitic stainless steels. This is often a preferred feature in pulp and paper construction, as it enables lighter structures and less material to be utilized. Today, lean duplex steels are widely available in various dimensions, from thin cold rolled sheets up to thick hot rolled plates. Lean duplex steels are also fully recyclable after the decommissioning stage of the equipment, thereby contributing to the circular economy.

Ning Gao,1,* Meng Li,2,* Weiming Wang,1 Lei Wang,3 Zhen Liu,4 Yufeng Guo1 1Department of Acupuncture and Moxibustion, Guang’anmen Hospital, China Academy of Chinese Medical Sciences, Beijing, 100053, People’s Republic of China; 2Department of Gastroenterology, Guang’anmen Hospital, China Academy of Chinese Medical Sciences, Beijing, 100053, People’s Republic of China; 3Department of Dermatology, China-Japan Friendship Hospital, Beijing, 100020, People’s Republic of China; 4Department of Gastroenterology, Xiyuan Hospital, China Academy of Chinese Medical Sciences, Beijing, 100091, People’s Republic of China*These authors contributed equally to this workCorrespondence: Zhen Liu, Department of Gastroenterology, Xiyuan Hospital, China Academy of Chinese Medical Sciences, No. 1 Xiyuan Playground, Haidian District, Beijing, People’s Republic of China, Email doctorliuzhen@126.com Yufeng Guo, Department of Acupuncture and Moxibustion, Guang’ an Men Hospital, China Academy of Chinese Medical Sciences, No. 5 Beixiange St., Xicheng District, Beijing, People’s Republic of China, Email gamgyf@139.comBackground: In recent years, the incidence of herpes zoster has risen steeply, the exact pathogenesis of the acute pain and the transformation into postherpetic neuralgia are still obscure, and the absence of effective management remains a major therapeutic challenge. The purpose of this study was to perform a qualitative and quantitative bibliometric analysis of the 100 most cited papers on herpes zoster.Materials and methods: Related literature were retrieved from the Web of Science Core Collection. Excel and VOSviewer software were applied to quantitatively analyze, and construct the bibliometric network charts.Results: The Top 100 most-cited papers published between 2000 and 2018 showed a fluctuating downward trend. The most studies were published in the year of 2000 (n = 12). The article entitled “A vaccine to prevent herpes zoster and postherpetic neuralgia in older adults” from Oxman MN, was the most-cited publication. The United States was the most contributing country, followed by the United Kingdom, and Italy. Finland occupied the highest citations per publication (CPP). The University of Colorado topped the list of institutions with the most publications with 18 articles and also had the most citations (average citations: 281.78 per article). Myron J Levin from the University of Colorado School of Medicine is the most published and most cited researcher overall, whereas Duke University’s John W Gnann tops the list in terms of average CPP.Conclusion: In terms of the quantity of T100 articles, researchers, and organizations, the US is the predominant country. The most T100 papers were published in the special journal Clinical Infectious Diseases. The most academic focus remain the remedies for postherpetic neuralgia and vaccine development for individualized groups.Keywords: herpes zoster, bibliometric study, top-cited, citation, VOSviewer

In any big institution,especially educational institutions like schoolsor colleges, generation of large quantity ofwaste papers is quite apparent. And effective use of recycled paper is also possible (craft papers, registers etc). So, instead of disposing off the waste papers into trash, recycling themmakes sense. This not only helps the institute in cost saving but will also ensure its contribution towards the protection of the environment. Designing automatically operated small-scaled paper recycling plant, which can be used in schools and colleges, ensures that a cheap and non-complex methodof production of paper product is guaranteed.Accordingly design of the machine unit has been prepared with all necessary component specifications.