Search

The study aimed at the use of char produced during pyrolysis of mix plastic waste. It further focused on producing activated carbon from char and also found its efficacy as efficient adsorbent for treatment of pulp and paper mill wastewater. The activated carbon was characterized in comparison with raw char for their physical, surface and adsorptive properties. Batch type adsorption experiments were carried out using 100 ml wastewater to observe the individual effectiveness using five different variables such as adsorbent dose (0.25–2.0 g), pH (6–10), time (5–24 h), agitation speed (100–200 rpm) and temperature (30–50 °C) by keeping other variables constant which helped to find out the effective range of all the variables. The competency was evaluated on the basis of colour and lignin content of pulp and paper industry wastewater. Once the effective range of different variables was identified, the statistical analysis was conducted to monitor the mutual impact on the reduction in colour and lignin contents in wastewater. From the statistical design applied, the best result was obtained at activated carbon dose (1.25 g), pH (8.0), contact time (7 h), agitation speed (184 rpm) and temperature (40 °C). The study resulted in reduction of 96.48% in colour and 94.25% in lignin at optimized condition in comparison with 87.37 and 80.44%, respectively, at unoptimized conditions. A potential increase in reduction of 9.0% in colour and 14.0% in lignin content was achieved after optimization through statistical design that confirmed its usefulness.

A simple electrochemical approach has been strategically developed for in situ generations of ZnO nanoparticles using Zn rods as electrodes and hydrogen peroxide as the oxidant without the formation of any by-product. These ZnO nanoparticles were extended for remediation of pollutants present in paper mill effluents, and separation efficiency was found to be above 90% for hydrocarbons, 92% for lignin, 99% for phenol, and 93% of chemical oxygen demand (COD), as confirmed by gas chromatography-mass spectrometry and COD analysis. It was also observed that the experimental setup could successfully remove 99% of the color from the sample. These ZnO nanoparticles have been proven in the past to be antibacterial and were explored for its ability to inhibit the growth of both Gram-positive and Gram-negative bacteria in the effluent samples after the removal of toxic pollutants. Therefore, we proposed an electrochemical reaction for the in situ synthesis of ZnO nanoparticles for remediation of paper mill effluent as well as inhibit the bacterial growth in the treated effluent sample.

Due to their unique properties, paper-based biosensors have attracted attention as inexpensive devices for on-site analysis. To achieve fast and sensitive detection of analytes, immobilization of enzymes with high apparent activities on paper is highly desirable; however, this is challenging. Herein, we report an improved approach to attach a malathion degrading enzyme, PoOPHM9, on paper via an interlocking network of Pluronic F127 (PF127)–poly(acrylic acid)–enzyme conjugates. The addition of PF127 improved retention of enzymatic activity as the apparent kinetic constant Vmax of the immobilized enzyme increased two-fold compared with the paper prepared without PF127. The PF127–poly(acrylic acid)–PoOPHM9 papers provided rapid colorimetric detection of malathion at 0.1–50 mM. The detection was completed within 5 min using a smartphone and image analysis software. As a proof-of-concept, malathion-contaminated water, plant, and apple samples were analyzed with the papers successfully. This material is promising for on-site rapid analysis of malathion-contaminated samples.

In this study, Taguchi experimental design was used to the optimize operating parameters for the degradation of paper mill effluent using electrochemical (EC) process with two-dimensional concentric aluminum tube electrodes (CATE). For this purpose, four significant experimental factors were used in four levels pH (6–9), electrolysis time (10–40 min), voltage (6–12 V) and surface area (357–624 cm(2)). The process parameters were optimized, through performing L16 orthogonal array of Taguchi technique, for the removal of chemical oxygen demand (COD) and turbidity. The percent COD and turbidity reductions were transferred into an accurate S/N ratio for a larger value is the better (LBT) response. The study presents a unique method of finding optimum combination of process parameters to illustrate their effect on the turbidity and COD reduction. The treatment conditions for the maximum elimination of the pollutants were second level of pH (7), third level of ET (30 min), fourth level of voltage (12 V) and second level of surface area (446 cm(2)). The confirmation experiment results were within the confidence intervals (CI) indicating an acceptable agreement between predicted and observed values. Based on the p-values, the electrolysis time and voltages were found to be the most significant factors for both COD and turbidity reduction. The findings of research indicated, that the Taguchi method can be used successfully for the treatment of paper industry effluent by electrochemical technique.

In this research, simultaneous quantification of cysteine (Cys) and histidine (His) using a paper-based sensor was investigated for the first time. A microfluidic paper-based sensor is a promising amino acid determination tool due to its low cost, low sample consumption, and fast analysis and is easy to make. We used SBA-15 as porous materials that are crystalline compounds formed with surfactants and TEOS as a silica source. The SBA-15 sample was characterized by X-ray diffraction, Fourier transform infrared, and scanning electron microscope techniques. The microfluidic paper-based sensors were fabricated using a wax pen, and the mesoporous SBA-15 modified filter paper. The fabricated sensors for Cys and His determination are operated based on an indicator-displacement assay. A comparative determination study of Cys and His on the sensors was carried out. The results illustrated that the addition of silica nanoporous material led to an immediate and uniform color change. The sensors were successfully exploited in the simultaneous determination of urinary Cys and His levels, thus providing the potential opportunity for clinical diagnosis. The linear range of 1.0 to 90.0 μM and 1.0 to 100 μM for His and Cys was obtained from the calibration data. The detection limits were also calculated (S/N = 3) for His and Cys of 0.5 μM and 1.5 μM, respectively. The proposed method showed a good agreement with the results achieved by a standard method.

This study focused on the applying endo-xylanases to reduce the use of bleaching agent, coupled with the production of xylooligosaccharides (XOs), in mulberry paper making. Paper mulberry pulp (PMP) was consecutively prepared from paper mulberry bark by traditional NaOH-treatment, and two types of thermostable endo-xylanase from Streptomyces thermovulgaris TISTR1948 (wild-type and recombinant endo-xylanases) were employed in the biobleaching of PMP. This process was optimized to achieve maximum XOs yields and the highest PMP quality. The optimal condition was an enzyme dosage of 125 U/g PMP at 12 h of reaction time, both in a 500 mL laboratory bottle and a 150 L reactor. The mixture obtained from the reactor was separated as liquid of XOs derived from PMP (PMP-XOs) and solid biobleached PMP. The PMP-XOs from wild-type endo-xylanase were composed of 31.6% xylopentaose (X5), 30.9% xylohexaose and higher-degree XOs (X ≥ 6), and 11.7% xylobiose (X2), whereas 76.6% of X5 and 8.6% of X2 were the main products from recombinant endo-xylanase. The PMP-XOs derived from both endo-xylanase types exhibited high antioxidant activities, reducing power, phenolic contents, and prebiotic efficacy. In addition, the application of both endo-xylanases enhanced the brightness of PMP by 5.1% and 3.5%, and reduced the kappa number by 9.1% and 3.6%, respectively. Biobleached PMP was subsequently subjected to the NaOCl bleaching step to produce the mulberry paper. This approach could reduce NaOCl consumption by 20–25%, making it an environmentally friendly alternative. The production of valuable prebiotics, such as PMP-XOs, further enhances the economic viability of this approach.

A high-barrier, strong, and antibacterial paper was fabricated by coating the acetylated cellulose solution with different contents of cinnamaldehyde (CIN) on Kraft paper. The antibacterial, antioxidant, mechanical, and barrier properties of coated paper were investigated. When the amount of CIN added in coating reached 6% v/v, the coated paper exhibited excellent antioxidant activity and antibacterial activity against Escherichia coli and Staphylococcus aureus. Notably, the dry and wet tensile strength of paper after coating was increased by 26.4 and 10.6 MPa, respectively. Furthermore, the coated papers' barrier properties against oil, water, water vapor, and oxygen were dramatically improved, especially for the water barrier rate up to 96.4%. Our coated papers with over 6% v/v CIN could extend beef's shelf-life for at least 4 days, which exhibited a promising prospect in eco-friendly antibacterial packaging.

Organic sticky contaminants represent one of the biggest technical challenges in the paper recycling process. These contaminants reduce paper strength, cause plugging of wires and felts, and stick to or deposit on machine parts affecting the runnability of the paper machine. The removal of these sticky contaminants is difficult to achieve along the process due to the heterogeneous nature of these organic contaminants. In this study, the nature of sticky contaminants in multiple wastepaper grades was analyzed and characterized using screening, solvent extraction with subsequent analysis such as FT-IR, GC-MS, and SEM. The content of stickies in wastepaper varies among different paper grades and their recovery methods. The majority of wastepaper grades collected from a recycled paper mill contains 3–5 wt% stickies, while a sample from a curb side collection from a residential area contains about 15 wt% stickies. Polyvinyl acetate (PVA) polymers, styrene butadiene rubber (SBR), paraffin waxes and polyamines are the major components in the extracted sticky contaminants. In addition, these stickies deposit heavily on fibers surface leading to high negative charge in fibers suspension ranging between 2 ~ 4.5 µeq/L. It is expected that these findings will assist addressing the knowledge gaps in understanding the nature of stickies and their behaviors, and to eventually develop highly efficient technologies for contamination removal in the paper recycling process.

Apart from protecting the environment from undesired waste impacts, wastewater treatment is a crucial platform for recovery. The exploitation of suitable technology to transform the wastes from pulp and paper industries (PPI) to value-added products is vital from an environmental and socio-economic point of view that will impact everyday life. As the volume and complexity of wastewater increase in a rapidly urbanizing world, the challenge of maintaining efficient wastewater treatment in a cost-effective and environmentally friendly manner must be met. In addition to producing treated water, the wastewater treatment plant (WWTP) has a large amount of paper mill sludge (PMS) daily. Sludge management and disposal are significant problems associated with wastewater treatment plants. Applying the biorefinery concept is necessary for PPI from an environmental point of view and because of the piles of valuables contained therein in the form of waste. This will provide a renewable source for producing valuables and bio-energy and aid in making the overall process more economical and environmentally sustainable. Therefore, it is compulsory to continue inquiry on different applications of wastes, with proper justification of the environmental and economic factors. This review discusses current trends and challenges in wastewater management and the bio-valorization of paper mills. Lignin has been highlighted as a critical component for generating valuables, and its recovery prospects from solid and liquid PPI waste have been suggested.

Malnutrition, muscle loss, and cachexia are prevalent in cancer and remain key challenges in oncology today. These conditions are frequently underrecognized and undertreated and have devastating consequences for patients. Early nutrition screening/assessment and intervention are associated with improved patient outcomes. As a multifaceted disease, cancer requires multimodal care that integrates supportive interventions, specifically nutrition and exercise, to improve nutrient intake, muscle mass, physical functioning, quality of life, and treatment outcomes. An integrated team of healthcare providers that incorporates societies’ recommendations into clinical practice can help achieve the best possible outcomes. A multidisciplinary panel of experts in oncology, nutrition, exercise, and medicine participated in a 2-day virtual roundtable in October 2020 to discuss gaps and opportunities in oncology nutrition, alone and in combination with exercise, relative to current evidence and international societies’ recommendations. The panel recommended five principles to optimize clinical oncology practice: (1) position oncology nutrition at the center of multidisciplinary care; (2) partner with colleagues and administrators to integrate a nutrition care process into the multidisciplinary cancer care approach; (3) screen all patients for malnutrition risk at diagnosis and regularly throughout treatment; (4) combine exercise and nutrition interventions before (e.g., prehabilitation), during, and after treatment as oncology standard of care to optimize nutrition status and muscle mass; and (5) incorporate a patient-centered approach into multidisciplinary care.

This work analyzes the energy performance implications of the physicochemical properties and the mineralogical elemental composition of agro-industrial wastes in the form of pellets (ISR pellets) and pine bark chips (PBCh). ISR pellets were made from a mixture of industrial wastewater treatment plant (IWTP) primary sludge, coal boiler ashes (CBA), and wood waste chips (WW), which are wastes rich in inorganic material and with a usable energy potential. All these residues were obtained from the production processes of paper company (Smurfit Kappa Colombia). ISR pellets and PBCh were tested as individual and mixed fuels in the thermochemical gasification and combustion processes. Several synergistic effects were found through the co-processing of these fuels, resulting in improvements in the performance indices normally used for the energy assessment of waste, as well as substantial environmental impact and operational behavior improvements. These effects were predicted through fusibility correlations from the elemental composition of the inorganic content, particularly the low melting point salts precursor species and fusibility temperature, as developed for coal ashes. The results of experimental co-processing validated these predictions.

The present study reports the characterization of reverse osmosis (RO) technology at water treatment plant Cogen-2 in paper and Board mills, Pakistan. RO is a commonly used process to obtain de-mineralized water for high-pressure boiler operation in thermal power plants. Scaling and fouling in three-stage RO plants is a major challenge in chemical industry due to the use of raw brackish water in the power plant of paper and board mills. In our study, the feed water quality of RO was changed from soft water to raw water to make it economical. The cleaning frequency was increased three times than normal, which was unsafe for operation and it was required to control scaling and fouling to achieve the desired result. Differential pressures behavior of all stages for 2-month data was observed without acid treatment, and the results of Langelier Saturation Index (LSI) control parameters (temperature, pH, total dissolved solids, calcium hardness, and alkalinity) clearly showed the abnormality. To optimize scaling and fouling of RO, the LSI factor was controlled in total reject water for the next 2 months by acid treatment in feed water. Duration of chemical cleaning and membranes’ life has been extended by fouling and scaling control. Understanding the effect of operational parameters in RO membranes is essential in water process engineering due to its broad applications in drinking water, sanitation, seawater, desalination process, wastewater treatment, and boiler feed water operation. The product flow increased from 18.3 to 19.9 m3/h, and this was due to a decrease in the rejection flow from 8.2 to 6.7 m3/h. The total reject stream pressure also increased from 8.1 to 9 bar. A lower value of LSI of 1.6 is obtained in the reject water stream after the acid treatment.

The problem of utilizing and processing cellulose and mineral fibrous waste contained in sludge obtained following mechanical treatment of wastewater from the production of paper and cardboard from recyclable materials is analyzed. A technology for producing a cellulose-mineral sorbent from this type of waste to mitigate emergency spills of oil and oil products is described. It is shown that an affordable, fast-acting and convenient sorbent can be produced from these wastes, having sufficient sorption capacity and the ability to retain oil products. The contaminated material can be safely and economically reclaimed or destroyed following use. Mechanisms for activating sorption properties, along with the composition, properties, and options for practical application of the sorbent, are considered.

Synthetic cannabinoid receptor agonists (SCRAs) are a class of varied compounds that mimic the effects of natural cannabinoids found in cannabis. Because they have a wide range of diverse structures, they vary widely in their potency. The abuse of new psychoactive substances (NPS) in prisons was reported in many European countries and in the USA. In the present study, we have described the identification of SCRAs in 56 infused paper sheet samples, seized mainly in Brazilian prisons between 2016 and 2020. The materials were seized by local or federal law enforcement and analyzed by Sao Paulo State Police or Brazilian Federal Police using gas chromatography–mass spectrometry, attenuated total reflection-Fourier transform infrared spectroscopy, liquid chromatography–high-resolution mass spectrometry or nuclear magnetic resonance spectrometry. Most of these samples (87.5%) were seized in 2019–2020; seven different SCRAs were identified in samples, and the most frequently identified substances were MDMB-4en-PINACA (23.6%) and 5F-MDMB-PICA (36.4%), the newest SCRAs emerging recently. As observed in Europe and the USA, Brazil also shows the prevalence of indazole-3-carboxamides and indole-3-carboxamides among SCRAs seizures in the prison system. This phenomenon is spreading all over the world at this moment. These data on the prevalence could help to alert judicial authorities to shutting down the introduction of NPS, including SCRAs, into prisons to ensure safety and security for avoiding health risks of prisoners and staff, leading to positive effects in this population. To our knowledge, this is the first demonstration of SCRAs smuggling into prisons in Latin America.

Background Coronavirus Disease 2019 (COVID-19), firstly reported in China last November 2019, became a global pandemic. It has been shown that periods of isolation may induce a spike in alcohol use disorder (AUD). In addition, alcohol-related liver disease (ALD) is the most common consequence of excessive alcohol consumption worldwide. Moreover, liver impairment has also been reported as a common manifestation of COVID-19. Aims The aim of our position paper was to consider some critical issues regarding the management of ALD in patients with AUD in the era of COVID-19. Methods A panel of experts of the Italian Society of Alcohology (SIA) met via “conference calls” during the lockdown period to draft the SIA’s criteria for the management of ALD in patients with COVID-19 as follows: (a) liver injury in patients with ALD and COVID-19 infection; (b) toxicity to the liver of the drugs currently tested to treat COVID-19 and the pharmacological interaction between medications used to treat AUD and to treat COVID-19; (c) reorganization of the management of compensated and decompensated ALD and liver transplantation in the COVID-19 era. Results and Conclusions The COVID-19 pandemic has rapidly carried us toward a new governance scenario of AUD and ALD which necessarily requires an in-depth review of the management of these diseases with a new safe approach (management of out-patients and in-patients following new rules of safety, telemedicine, telehealth, call meetings with clinicians, nurses, patients, and caregivers) without losing the therapeutic efficacy of multidisciplinary treatment.

Materials containing silver nanoparticles (AgNPs) are of great interest for household uses, including drinking water disinfection. Although various Ag-containing materials are available, the development of low-cost, reusable, and durable systems is a challenge in water disinfection. Herein, we developed a low-cost, reusable, and durable cellulose filter paper (CFP) containing AgNPs decorated with a tannic acid (TA) and chitosan (CS) matrix (CFP-CSTAAg). The formation of CFP-CSTAAg composite was confirmed by FTIR, and XRD techniques. The formation of CSTAAg composite on CFP greatly improved the mechanical performance. CFP-CSTAAg is driven by gravity of 100 ml of a water sample containing Staphylococcus aureus for 30 min. The composite showed 99 % killing efficiency of bacteria as the bacteria cells did not pass through composite. The low-cost CFP-CSTAAg composite was reusable, providing a 98 % bacteria-killing capacity after five treatment cycles. The product’s properties make reusable CFP-CSTAAg composite a promising filter for durable water disinfection as it is a low-cost material and eco-friendly.

Dual-purpose coated paper, which enables in-line inkjet printing with web offset, can be used for both offset and inkjet prints. This product has potential to meet the ever-increasing demand for printing individualized information on commercial printing materials. In this work, commercial samples were printed in the two presses. It was deduced that low permeability correlates with large color gamut volume. The correlation would be useful to design coating formulations for good printability. Also, we examined the packing of coating layers to identify a coating formulation that provides good printing quality in both offset and inkjet printing. Many combinations of pigments were tested, and the effects of particle shape on viscosity and packing were examined. For all coating colors, pigment mixtures with a weight ratio of 3:1 gave the highest packing density. The mixture of GCC 90 and delaminated clay with a weight ratio of 3:1 was the best selection studied for dual-purpose coated paper. Among commercial paper samples, a web offset coated paper showed the best overall performance, indicating that coating formulations with minimal blistering are suitable for dual-purpose coated paper.

The salivary glands are closely associated with stress conditions and the neuroendocrine system. The concentrations of these salivary biomarkers fluctuate with a person’s disease status. Until now, salivary diagnostics have been promising; however, the analytical tools for detecting salivary biomarkers have remained burdensome due to the lack of user-friendly and cost-effective equipment. In this study, we used a microfluidic starch-coated paper-based chip to isolate ɑ-amylase from human saliva. The concentration of ɑ-amylase on the head and tail sections of the paper-based chip was compared in the presence or absence of starch. We found that ɑ-amylase was highly concentrated only in the head section of the starch-coated paper-based chip through Western blotting (WB) and enzyme-linked immunosorbent assay (ELISA). We expect our designed paper-based chip will aid in α-amylase detection technologies using saliva and small amounts of other biofluids including blood, tears, pancreatic juice, and urine.

Organic dyes are used in many industries, e.g., textile, cosmetics and food. Hence, contamination of organic dyes to water sources is a critical issue. To reduce water pollution by organic dyes, we propose a paper-like adsorbent with a practical and economical production procedure. Subsequently, a flexible adsorbent was produced using a one-step approach by vacuum filtration of graphene oxide (GO) and iron oxide nanoparticles (Fe3O4-NPs) containing dispersion through a membrane and quoted as GO/Fe3O4 paper. For comparison, GO paper was also prepared using the same procedure. Both papers were characterized using UV–VIS absorption spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, electron diffraction X-ray analysis, X-ray photoelectron spectroscopy, and powder X-ray diffraction techniques. At the steady-state conditions, GO/Fe3O4 and GO papers were performed as adsorbent for cationic dyes of methylene blue, neutral red, and anionic dyes of methyl orange and fluorescein. In general, the removal efficiency of GO/Fe3O4 paper was higher than that of GO paper for adsorption of all dyes and this adsorbent revealed satisfactory adsorption properties for cationic dyes when compared to anionic dyes.

Magnetic Resonance Imaging linear-accelerator (MRI-linac) equipment has recently been introduced to multiple centres in Australia and New Zealand. MRI equipment creates hazards for staff, patients and others in the MR environment; these hazards must be well understood, and risks managed by a system of environmental controls, written procedures and a trained workforce. While MRI-linac hazards are similar to the diagnostic paradigm, the equipment, workforce and environment are sufficiently different that additional safety guidance is warranted. In 2019 the Australasian College of Physical Scientists and Engineers in Medicine (ACPSEM) formed the Magnetic Resonance Imaging Linear-Accelerator Working Group (MRILWG) to support the safe clinical introduction and optimal use of MR-guided radiation therapy treatment units. This Position Paper is intended to provide safety guidance and education for Medical Physicists and others planning for and working with MRI-linac technology. This document summarises MRI-linac hazards and describes particular effects which arise from the combination of strong magnetic fields with an external radiation treatment beam. This document also provides guidance on safety governance and training, and recommends a system of hazard management tailored to the MRI-linac environment, ancillary equipment, and workforce.

Purpose The most abundant among the separately collected waste materials in Italy is food waste. This research aims to evaluate the influence of the type of collection bag on the food waste management chain. In Italy, the food waste collection is mainly based on bioplastic bags. As an alternative, a new type of recycled paper bag shows potential advantages. Methods The two types of collection bag were compared evaluating the weight loss of food waste during the household storage, by means of an experimental assessment simulating the domestic dynamic bag filling. Moreover, the biomethane production of bags under anaerobic conditions was measured at the lab-scale level with Biochemical Methane Potential (BMP) tests. Results During the household storage, the breathable fabric of the paper allows for higher weight losses, ranging on average between + 29 and + 44% compared to bioplastic. BMP tests, carried out under different conditions (temperature, inoculum), showed a 2–14 times higher generation of methane by paper bags compared to bioplastic bags, when referred to 1 kg of inserted food waste. Conclusions Collecting the food waste inside paper bags shows advantages compared to the use of bioplastic bags. First, the waste collection is benefitted thanks to the lower weight of material to be transported to treatment plants, leading also to the possibility of decreasing the collection frequency. Moreover, paper resulted more compatible than bioplastic with the anaerobic digestion treatment, which is currently rapidly increasing as a food waste management option. Graphic Abstract

In this elucidation, we synthesized novel molecularly imprinted polymers (MIPOH1-4) that were used as organic fillers on bagasse pulp to form cellulosic paper sheets, the formation of MIPOH1-4 from the reaction of enaminone 3 with methyl methacrylate monomer in the presence of ethylene glycol dimethyl acrylate and 2,2’-azobisisobutyronitrile. The obtained MIPOH1-4 was confirmed via FT-IR and SEM with different pore sizes. And we noticed that the increase of template 3 increases the hydrogen bond between monomer and template and gave sponge surface of MIPOH4. Furthermore, the computational energies of the template with different monomers utilize DFT/B3LYP/6-31G (d) level to know the stability of polymers and hydrogen bonding between them. So that we applied that in paper manufacture through the adsorption of MIPOH4 as an organic filler on bagasse pulp to form novel cellulosic paper sheets with different concentrations and these sheets which characteristic through FT-IR, SEM, sizing test, tensile strength, and elucidation their antimicrobial activity with theoretical and docking studies. The MIPOH4 and cellulosic paper sheets showed the thermal stability and high tendency of sizability of these paper sheets and concluded the interaction between cellulose fibers of pulp with MIPOH polymer with physical hydrogen bonding.

This paper is aimed to develop a hybrid model (PCA-ANN) to predict the extractive content in eucalyptus wood clones. The input variables to the virtual analyzer are planting parameters available from the forest inventory, therefore the prediction does not rely on laboratory analysis of the wood samples, affording a quick estimate of the extractive contents. This study further bridges the literature gap on the investigation of the cause of variability of extractive content in eucalyptus wood. The PCA-ANN was identified from experimental data to predict and monitor the extractive content, since laboratory measurements can take several days and become available only after wood processing. The experimental data contained information on ten species of eucalyptus clones from five regions in the extreme south of Bahia, Brazil. Principal Component Analysis (PCA) firstly assessed the impact of planting variables on the extractives content. The variability of the data was represented by eight principal components and the variables that mostly contribute to the extractive content are: potential acidity, iron, saturation of aluminum, magnesium, pH, base saturation, remaining phosphorus, zinc, manganese and copper. The artificial neural network (ANN) with the 8 principal components in the input layer showed that the PCA could effectively reduce the dimensionality of the data. For practical purposes, though, the ANN with 10 input variables and 16 neurons in the hidden layer, presenting an average relative deviation of 1.5%, is recommended. The prediction of the extractive content is essential to allow preventive management practices toward the improvement of yield and quality of the cellulosic pulp.

It remains a challenge to prepare special engineering paper with excellent mechanical properties, high temperature resistance and chemical resistance. The emergence of high-performance fiber provides support for the technical progress of special engineering paper. Herein, a novel method to obtain a novel self-reinforced poly (ether ether ketone) (PEEK) composite paper (SR-DI-PEEK/paper) by vacuum filtration, impregnation and hot pressing. Specially, PEEK fibers were used as the skeleton fiber and a small amount of aramid pulp was added as the decanted fiber. By optimizing the process of SR-DI-PEEK/paper preparation, the best mechanical properties of SR-DI-PEEK/paper was presented. Compared with the composite paper prepared with Phenolic solution (PF-PEEK/paper) and Polyimide solution (PI-PEEK/paper), the mechanical properties of SR-DI-PEEK/paper was significantly improved. In particular, when the concentration of impregnation was 3 wt%, the tensile index of SR-DI-PEEK/paper reached 51.10 N m g−1 (tensile strength 47.16 kN m−1), which is 16.48 times than that of the un-impregnated PEEK/paper (2.86 kN m−1). SR-DI-PEEK/paper also exhibited excellent chemical resistance among acid, alkali, and polar solvents, while the tensile index maintained 96.3% after 40 wt% H2SO4 treatment. Besides, SR-DI-PEEK/paper showed superior thermal performance, while the temperatures corresponding to the weight loss of 5% were 574 °C.

Microfluidic paper-based analytical devices (μPADs) have developed rapidly in recent years, because of their advantages, such as small sample volume, rapid detection rates, low cost, and portability. Due to these characteristics, they can be used for in vitro diagnostics in the laboratory, or in the field, for a variety of applications, including food evaluation, disease screening, environmental monitoring, and drug testing. This review will present various detection methods employed by μPADs and their respective applications for the detection of target analytes. These include colorimetry, electrochemistry, chemiluminescence (CL), electrochemiluminescence (ECL), and fluorescence-based methodologies. At the same time, the choice of labeling material and the design of microfluidic channels are also important for detection results. The construction of novel nanocomponents and different smart structures of paper-based devices have improved the performance of μPADs and we will also highlight some of these in this manuscript. Additionally, some key challenges and future prospects for the use of μPADs are briefly discussed.

Thermochemical parameters of A4-sized printing paper (AP), filter paper (FP), newspaper (NP), writing paper (WP), and reed pith (RP) samples were estimated using standard protocol to identify its fuel characteristics, and thermal degradation of the same was studied using thermogravimetric analysis (TGA) and differential thermogravimetric (DTG) techniques in the temperature range of 30–800 °C at the heating rates of 10, 15, and 20 °C/min under nitrogen atmosphere. The curves of TGA and DTG exhibited four significant stages. Maximum weight loss was found to be in the second stage. Kinetic analysis was carried out in the conversion range of 0.1 to 0.7 using iso-conversational models of Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), Vyazovkin, and Vyazovkin AIC (V.AIC). The average activation energies were found to be 139.90, 115.93, 212.52, 257.41, and 241.63 kJ/mol using FWO; 129.73, 103.06, 202.46, 248.38, and 231.55 kJ/mol using KAS; 145.57, 134.00, 195.29, 256, and 241.63 kJ/mol using Vyazovkin; and 140.71, 133.86, 193.14, 247.57, and 190.14 kJ/mol using Vyazovkin AIC model. Thermodynamic parameters (enthalpy change (ΔH), Gibbs free energy change (ΔG), and entropy change (ΔS)) using these models have been evaluated.

All-cellulose paper-based composites with underwater superoleophobicity and high-wet-strength were developed by casting a barrier layer of bacterial cellulose (BC) on a filter paper substrate. To optimize the pore structure of barrier layer, slow gel process of BC dispersion was conducted via acidification and solvent exchange. 1,2,3,4-butanetetracarboxylic acid was used to improve the wet strength and surface hydrophilicity through the crosslinking reaction between fibers. The underwater oil contact angles are higher than 150° in neutral environment, and slightly decrease under acid and alkali conditions. Combined with the micron-sized pore structure of BC barrier layer, the composite papers show good separation performance of oil-in-water emulsion. A denser BC layer can significantly improve the separation efficiency, but also lead to the reduction of flux. During the gelation of BC barrier layer, the increase in the ethanol/water ratio of the dispersion medium is able to increase the flux without obvious negative impact on the separation efficiency. When the ethanol/water ratio is 80%, the separation efficiency and water flux reach 99.2% and 1320 L m−2 h−1·bar−1 for the emulsified soybean oil with the average size of 13 μm, respectively. This type of all-cellulose composite papers provides a new idea for the fabrication of membrane materials for oil–water separation.

Currently, most of the collected waste medium-density fiberboards (MDF) is incinerated or landfilled, as economically viable recycling methods are yet to be developed. By steam refining waste medium-density fiberboards (MDF), it is possible to hydrolyze the incorporated resins and isolate a high yield fiber fraction. Further refining of the steam treated fibers might enable the fibers to be utilized in applications such as paper packaging, facilitating a cascading use of the waste material stream. To this end, intimate knowledge of the material is needed. In this study, the steam refined fibers of two waste MDF samples containing differing amounts of softwood and hardwood underwent refining and beating. The resulting fibers were characterized regarding their morphology and paper test sheets were produced to evaluate their strength (compression-, tensile- and tear-strength). Distinct differences in response to refining between the MDF samples were apparent. For the sample with the higher hardwood share an increase in strength properties with increasing steam treatment severities could be observed and it was possible to produce test sheets with comparable compression strength to recycled pulp for industrial corrugated paperboard. For the sample with a higher share of softwood, the steam treatment severity did not show any influence on fiber morphology or paper properties, and the resulting paper strength was low in comparison to the other steam refined waste MDF sample. Graphic Abstract

The kapok (Ceibapentandra (L.) Gaertn) seed fibre is unicellular with length up to 35 mm, however, it is covered by a hydrophobic waxy layer that limits its application in paper production. In this study, the effect of various pulping methods namely mechanical, chemi-mechanical, semichemical and chemical pulping on kapok fibre properties was investigated. Each kapok pulp was then blended with the secondary fibre recovered from kraftliner board for handsheet making to examine their reinforcing ability on strength properties. The results showed that kapok mechanical pulps (with and without dewaxing (5% (v/v) diluted detergent) and chemimechanical pulp were unable to improve the strength properties of the handsheet. Kapok pulps chemically treated with 18–25% of sodium hydroxide gave a better effect on handsheet strength properties whilst fibre treated with 20% sodium hydroxide showing the highest increment. Although the reinforcing effect of the 4% native cooked starch was slightly higher than that of the 10% kapok pulp blended in recycled paper, the recycling potential of the latter was better as all strength properties retained unchanged after recycling. The findings indicated that kapok chemical pulp is a promising reinforcing fibre source with superior recycling potential.

The uses of natural dyes are getting popularized due to the increased awareness regarding the toxicity of many chemical colorants. The chemical colorants are being replaced by the natural colorants for the various industrial applications. The plant-based natural colorants are considered eco-friendly and toxic free. In the present study, we report a natural dye from the heartwood of Caesalpinia sappan suitable for paper based packing materials. This forms the first report on the study of natural dye obtained from the heartwood of C. sappan on paper material. The extracted dye had a good photostability and able to make imprints on recycled paper bags. Moreover, a significant inhibition of bacterial growth was observed at a higher dye concentration of 100 μg mL−1 against P. aeruginosa which was higher than the standard antibiotics. Growth inhibition was also observed in case of B. subtilis (22 ± 0.17 mm) and K. pneumonia (21 ± 0.53 mm) at 100 μg mL−1. The dye could be used in making medicated packing materials and have many other bio-potential which was validated through in silico toxicity analysis. The application of such natural dyes in paper material value addition will help in a cleaner and sustainable process during paper recycling.

The pulp and paper industry is a major source of lignocellulose-containing streams. The components of lignocellulose material are lignin, hemicellulose, and cellulose that may be hydrolyzed into their smaller components and used as feedstocks for valorization efforts. Much of this material is contained in underutilized streams and waste products, such as black liquor, pulp and paper sludge, and wastewater. Bacterial fermentation strategies have suitable potential to upgrade lignocellulosic biomass contained in these streams to value-added chemicals. Bacterial conversion allows for a sustainable and economically feasible approach to valorizing these streams, which can bolster and expand applications of the pulp and paper industry. This review discusses the composition of pulp and paper streams, bacterial isolates from process streams that can be used for lignocellulose biotransformations, and technological approaches for improving valorization efforts. KEY POINTS: • Reviews the conversion of pulp and paper industry waste by bacterial isolates. • Metabolic pathways for the breakdown of lignocellulose components. • Methods for isolating bacteria, determining value-added products, and increasing product yields.

In traditional deinking process, large amounts of chemicals are required which makes these methods expensive and polluting. Also, application of sustainable material implies the use of green processes to reduce waste and pollution. Green enzymatic deinking processes are alternatives to those technologies that have negative effects on the environment. In this work, we applied response surface methodology for deinking the electrophotography-printed paper based on a systematic experimental pattern. The individual and interactive effects of enzymatic deinking parameters including time, temperature, and enzyme dosage on the handsheet properties were investigated. Different analyses were carried out to determine the best process conditions of enzymatic deinking to optimize the handsheet properties (i.e., tensile, burst, whiteness, and brightness). The obtained responses of an oven-dried fiber at 45 min, 43 °C and the enzyme concentration of 1 mg/15 g were 12.44, 0.65, 72.20, and 87 for tensile strength, burst strength, whiteness, and brightness, respectively. Measuring the optical density of the deinked handset after printing showed that the printability of the deinked paper is in the desired range.

A one-step analysis method was developed for four types of amino acids using a microfluidic paper-based analytical device fabricated from chromatography filtration paper and laminate films. Aminoacyl-tRNA synthetase was used to detect each amino acid. The obtained laminated paper-based analytical device (LPAD) contained four enzymatic reaction areas. Colorimetric detection was performed based on the molybdenum blue reaction. A model method for the simple, easy, and simultaneous detection of several amino acid concentrations was suggested, in contrast to the conventional methods such as HPLC or LC–MS. The method provided a selective quantification at the ranges of 3.6–100 μM for tryptophan, 10.1–100 μM for glycine, 5.9–100 μM for histidine and 5.6–100 μM for lysine with a detection limit of 1.1 μM, 3.3 μM, 1.9 μM and 1.8 μM, respectively. LPAD fabrication was considerably simple, and the subsequent detection process was easy and required a short period of time (within 15 min).

Printing technology for electronic devices has received significant attention owing to its fast and massive productivity under ambient conditions. In this study, a facile approach was proposed for manufacturing cellulose paper-based strain sensors with Ni/ multi-walled carbon nanotubes (MWCNT) composites using roll stamping technology. This process enables fabrication of stable sensing structures owing to the formation of stable Ni core enveloping structures in the MWCNT interlacing network. In particular, the rheological properties of the composites revealed shear thinning and thixotropic behaviors, which resulted in fine printing of the sensing electrodes. Furthermore, the shape of the printed patterns, impacted by the pattern morphology, significantly influenced the strain-sensing performance. In particular, the Ni/MWCNT composite-based strain sensor exhibited higher gauge factor of 13.9 with high sensing recovery of 90.4% and stability for 23,500 bending cycles test.

Since the first statement of the German Society of Oto-Rhino-Laryngology, hypoglossal nerve stimulation (HNS) is meanwhile an established treatment option for obstructive sleep apnea (OSA). There are three HNS systems available in Germany which differ in their technical details of the underlying comparable basic principle. For the unilateral HNS with respiratory sensing, several comparative studies, high-volume register analysis and long-term reports exist. The continuous HNS without respiratory sensing does not require a sleep endoscopy for indication. For the bilateral continuous HNS as the single partially implantable device, a feasibility study exists. For indication, the assessment of positive airway pressure failure by sleep medicine is crucial, and the decision for HNS should be made in discussion of other treatment options for at least moderate OSA. The implantation center holds primarily responsibility among the interdisciplinary sleep team and is primary contact for the patient in problems. This depicts why structural processes are required to secure outcome quality and minimize the complications. The aftercare of HNS patients can be provided interdisciplinary and by different medical institutions, whereat, minimal reporting standards to document outcome and usage are recommended.

Allergo journal international 30(5), 155-168 (2021). doi:10.1007/s40629-021-00178-2, Published by Urban & Vogel, München

Rearrangements in the anaplastic lymphoma kinase (ALK) and proto-oncogene tyrosine-protein kinase ROS (ROS1) genes characterise two distinct molecular subsets of non-small cell lung cancer (NSCLC) tumours. Lorlatinib is a third-generation ALK/ROS1 tyrosine kinase inhibitor (TKI) shown to have systemic and intracranial activity in treatment-naive patients and in those who progressed on first- and second-generation TKIs. Despite being generally well tolerated, lorlatinib has a unique and challenging safety profile that includes hyperlipidaemia and central and peripheral nervous system adverse events (AEs). This article summarises a set of strategies designed to monitor and manage lorlatinib-related AEs that were agreed upon by a multidisciplinary panel of specialists in a meeting held in July 2020. Among the recommendations hereby described, special emphasis was placed on communication: prescribing physicians should inform patients and their families/caregivers about the likelihood and nature of lorlatinib AEs, encouraging them to report any symptoms, while at the same time reassuring them that most events are manageable and resolve spontaneously and have little to no interference with cancer treatment. Importantly, all patients should undergo a set of baseline assessments, including biochemical analysis, evaluation of cardiovascular risk, electrocardiogram (ECG), neurological evaluation and contrast-enhanced magnetic resonance imaging of the brain, which should be repeated regularly during lorlatinib treatment. Supportive medications to treat or relieve lorlatinib AEs were also discussed, as were the conditions requiring specialist consultations and/or adjustments in lorlatinib therapy. The overall goal of this article is to serve as a practical guide for oncologists to systematically and effectively approach lorlatinib AEs.

Rising socioeconomic level and increasing popularity of e-commerce have dramatically increased the use of cardboard packaging materials, and consequent related recycling and wastes. Large amounts of sludge (up to 40% of input mass) is formed through the recycling process, with sludge solids that are very rich in cellulose fibers (~ 75% w/w). To date this sludge is mostly disposed in landfills, resulting in added economic and environmental costs to the recycling process. Short ozonation pretreatment of RPS resulted in enzymatic release of ~ 34% of the cellulosic fraction of the sludge as sugar, and fermentation of these sugars by yeasts resulted in production of ~ 15 g/L ethanol. The solid remnants, were used as a bio-sorbent, efficiently removing dyes from textile wastewater. Recycled paper sludge waste was thus a good source for both energy and water-treatment applications, increasing sustainability and circular economy in the paper and cardboard recycling industry.

Feedback is beneficial to students’ learning process and overall achievement, but one of the common complaints from students about college education is regarding feedback. So, this study aimed to examine whether digital written feedback positively influences students’ learning experience and attitude toward learning. Digital written feedback refers to feedback provided through a learning management system as handwritten feedback added to a scanned copy of the student’s paper-based assessment using a smart pad and smart pencil. The study surveyed a diverse set of college students’ (n = 175) perceptions regarding feedback satisfaction, learning satisfaction, the usefulness of digital written feedback, and perceived achievement via an online survey. A one-way analysis of variance found a significant difference between feedback satisfaction and learning satisfaction according to the feedback method. A multiple regression analysis indicated the satisfaction and perceived usefulness of digital written feedback predicted perceived achievement. From the students’ open responses regarding the benefits of digital written feedback, five themes emerged, namely usability, psychological relief, accessibility, self-regulation, and acceptance. The implications for digital written feedback are discussed.

This study evaluates the use of fermentation to increase nutrient availability in pulp and paper bio-sludge (PPBS) as feed for black soldier fly larvae (BSFL). Rearing of BSFL on fermented PPBS was carried out in a climate chamber in order to assess nutrient availability and larvae survival and growth. The PPBS used came from a chemo-thermomechanical pulp/groundwood pulp mill. The PPBS was fermented at 35 °C and 55 °C, respectively, at initial pH of 10. The effects of sediment and liquid from fermented PPBS on larvae dry weight, survival rate until the prepupae stage, bioconversion, and reduction rate of PPBS were measured. The bioconversion of the liquids (4.1–6.6%) was substantially higher than for both the sediments and untreated PPBS (≤ 0.4%). The survival rate, on the other hand, was substantially lower (26.3–30.9 %) than for the sediments and untreated PPBS (49.5–52.6%). Neither the sediments nor the liquids had significant effects on the larvae weight or on the PPBS reduction rate. The sediments had no significant effect on the survival rate or the bioconversion. This study demonstrates that fermentation dissolves a part of the PPBS and that dissolved substances in the fermentation liquid readily convert to larvae biomass. However, the bulk of the lignocellulose is not dissolved, and most of PPBS nutrients remain unavailable for growth of the larvae. Further research should focus on improved pretreatment of PPBS to increase availability of nutrients and thereby improve the feasibility of BSFL as a recycling method for PPBS.

Social aggression is a pervasive feature of insect societies. In eusocial Hymenoptera, aggression among females can affect task performance and competition over direct reproduction (egg laying); in most species males participate in social interactions relatively rarely. Males of the independent-founding paper wasp Mischocyttarus mastigophorus are exceptional: they are aggressive toward female nestmates, leading us to explore the function of this unusual behavior. We applied social network analyses to data on M. mastigophorus social aggression to quantify sex differences in giving and receiving social aggression. The network analyses supported the pattern of biased male aggression toward female nestmates; females are relatively rarely aggressive to males. We then asked whether male aggression toward females was biased by females’ relative ovary development. Males were more aggressive toward females with better-developed ovaries, opposite to patterns of aggression among females. Because food brought to the colonies is often monopolized by dominant females, we suggest that males direct aggression toward socially dominant females with better-developed ovaries to obtain food. The implications of biased male aggression for female task performance and physiology are unknown.

The objective of this study was to check the potential of crude xylano-pectinolytic enzymes in bleaching of rice straw pulp, in order to reduce the toxic waste load for managing the environmental pollution. The xylano-pectinolytic enzymatic bleaching step for delignification was found to be most effective at pulp consistency 1:10 g/ml, xylanase:pectinase dose of 9:4 IU/ml, pH 8.5 and treatment time 180 min at temperature of 55 °C, and resulted in lowering of kappa number of the rice straw pulp by 15.29%. In subsequent bleaching stages, this enzymatic pre-bleaching treatment also resulted in 30% reduction of active chlorine dioxide dose without any loss of optical properties. Significant improvement in various physical properties of the enzymes treated pulp, tear index (15.43%), breaking length (11.11%), double fold number (25.92%), burst index (9.88%) and viscosity (13.63%), and Gurley porosity (39.86%) was also noticed. This approach resulted in reduction of BOD and COD values by 21.07% and 26.57%, respectively. This is the first study on the use of crude xylano-pectinolytic enzymes for bio-bleaching of rice straw pulp.

Flexible electrodes are widely used in the manufacture of flexible sensors and wearable devices. However, with the development of science and technology and the large-scale utilization of metal resources, the question whether alternative materials can be found to ease the use of metal materials has been raised. Among them, paper-based electrodes have attracted special attention in the industry because of their degradability, low cost and high flexibility. Therefore, a low delay flexible paper-based electrode filled for capacitive sensors is proposed through carbon materials. Different from discussing the influence of single fiber, the paper-based electrode is manufactured by wet process. The effects of different fiber substrates on the physical properties and electrical signal properties of paper-based electrodes were discussed. The results show that the paper-based electrode has high conductivity, which is 18.52 S/cm. And there is a low delay in the process of electrical signal transmission. The phase frequency angle hardly changes at the signal frequency of 1 kHz, and the change of phase frequency angle is only 4.9 ° at the signal frequency of 300 kHz. The thickness of the guided electric paper is about 90 μm. Lower than common paper products. This study shows that the paper-based electrode has the advantages of high conductivity, low hysteresis, light and thin, which provides the possibility to be used as a flexible electrode.

We present a historical study of Quantum Technology 2.0 using more than 66,000 papers from 1980 to 2020 that had been assigned to four subfields. We applied the method reference publication year spectroscopy to respective publication sets of the subfields in order to identify their historical roots and seminal papers. We found 126 of them in total, 43 in quantum metrology and sensing, 46 in quantum communication and cryptography, 42 in quantum computing, and 33 in quantum information science–with a significant overlap between subfields–which are all discussed in their relevance for the respective subfield. We compared the subfields regarding their interrelationship and distinctiveness in terms of their most influential papers and were able to deduce a common core set of five seminal publications in all four subfields.

This study was performed to evaluate trends in and provide future direction for anesthesiology education, research, and clinical practice.We collected high-impact papers, ranking in the top 10% in the field of anesthesiology and published from 2011 to 2020, by the InCites tool based on the Web of Science Core Collection. We analyzed the trends, locations, distribution of subject categories, research organizations, collaborative networks, and subject terms of these papers.A total of 4,685 high-impact papers were included for analysis. The number of high-impact papers increased from 462 in 2011 to 520 in 2020. The paper with the highest value of category normalized citation impact (115.95) was published in Anesthesia and Analgesia in 2018. High-impact papers were mainly distributed in the subject categories of "Anesthesiology," "Clinical Neurology," "Neurosciences," and "Medicine General Internal." They were primarily cited in "Anesthesiology," "Clinical Neurology," "Neurosciences," "Medicine General Internal," and "Surgery." Most of these high-impact papers came from the USA, UK, Canada, Germany, and Australia. The most productive institutions were the League of European Research Universities, Harvard University, University of Toronto, University of London, University of California System, and University Health Network Toronto. Research collaboration circles have been formed in the USA, UK, and Canada. Subject-term analysis indicated postoperative analgesia, chronic pain, and perioperative complications were high-interest topics, and COVID-19 became a new hot topic in 2020.The current study provides a historical view of high-impact papers in anesthesiology in the past ten years. High-impact papers were mostly from the USA. Postoperative analgesia, chronic pain, and perioperative complications have been hot topics, and COVID-19 became a new topic in 2020. These findings provide references for education, research, and clinical practice in the field of anesthesiology.RéSUMé: OBJECTIF: Cette étude a été réalisée pour évaluer les tendances et fournir une orientation future à l’enseignement, la recherche et la pratique clinique en anesthésiologie. MéTHODE: Nous avons colligé des articles à fort impact, classés dans le top 10 % dans le domaine de l’anesthésiologie et publiés de 2011 à 2020, par l’outil InCites basé sur la Web of Science Core Collection. Nous avons analysé les tendances, les emplacements, la répartition des catégories de sujets, les organismes de recherche, les réseaux de collaboration et les termes des sujets de ces articles. RéSULTATS: Au total, 4685 articles à fort impact ont été inclus pour analyse. Le nombre de manuscrits à fort impact est passé de 462 en 2011 à 520 en 2020. L’article ayant la valeur la plus élevée de l’impact normalisé des citations de catégorie (CNCI) (115,95) a été publié dans la revue Anesthesia and Analgesia en 2018. Les articles à fort impact ont été principalement distribués dans les catégories de thèmes « Anesthésiologie », « Neurologie clinique », « Neurosciences » et « Médecine générale interne ». Ils ont été principalement cités dans les catégories « Anesthésiologie », « Neurologie clinique », « Neurosciences », « Médecine générale interne » et « Chirurgie ». La plupart de ces articles à fort impact provenaient des États-Unis, du Royaume-Uni, du Canada, d’Allemagne et d’Australie. Les établissements les plus productifs étaient la League of European Research Universities, l’Université Harvard, l’Université de Toronto, l’Université de Londres, l’Université de Californie System et le University Health Network de Toronto. Des cercles de collaboration en recherche ont été formés aux États-Unis, au Royaume-Uni et au Canada. L’analyse des termes indiquait que l’analgésie postopératoire, la douleur chronique et les complications périopératoires étaient des sujets suscitant un fort intérêt, et la COVID-19 est devenue un nouveau sujet brûlant en 2020. CONCLUSION: La présente étude propose une vue historique des articles à fort impact en anesthésiologie au cours des dix dernières années. Les manuscrits à fort impact provenaient principalement des États-Unis. L’analgésie postopératoire, la douleur chronique et les complications périopératoires ont été des sujets d’actualité, et la COVID-19 est devenue un nouveau sujet en 2020. Ces résultats fournissent des références pour la formation, la recherche et la pratique clinique dans le domaine de l’anesthésiologie.

Spatial orientation is based on a complex cortical network with input from multiple sensory systems. It is affected by training, sex and age as well as cultural and psychological factors, resulting in different individual skill levels in healthy subjects. Various neurological disorders can lead to different patterns or specific deficits of spatial orientation and navigation. Accordingly, numerous tests have been proposed to assess these abilities. Here, we compare the results of (1) a validated questionnaire-based self-estimate of orientation/navigation ability (Santa Barbara Sense of Direction Scale, SBSODS) and (2) a validated pen-and-paper two-dimensional perspective test (Perspective Taking Spatial Orientation Test, SOT) with (3) a newly developed test of finger-arm pointing performance in a 3D real-world (3D-RWPT) paradigm using a recently established pointing device. A heterogeneous group of 121 participants (mean age 56.5 ± 17.7 years, 52 females), including 16 healthy volunteers and 105 patients with different vestibular, ocular motor and degenerative brain disorders, was included in this study. A high correlation was found between 2D perspective task and 3D pointing along the horizontal (azimuth) but not along the vertical (polar) plane. Self-estimated navigation ability (SBSODS) could not reliably predict actual performance in either 2D- or 3D-tests. Clinical assessment of spatial orientation and memory should therefore include measurements of actual performance, based on a 2D pen-and-paper test or a 3D pointing task, rather than memory-based questionnaires, since solely relying on the patient’s history of self-estimated navigation ability results in misjudgments. The 3D finger-arm pointing test (3D-RWPT) reveals additional information on vertical (polar) spatial performance which goes undetected in conventional 2D pen-and-paper tests. Diseases or age-specific changes of spatial orientation in the vertical plane should not be clinically neglected. The major aim of this pilot study was to compare the practicability and capability of the three tests but not yet to prove their use for differential diagnosis. The next step will be to establish a suitable clinical bedside test for spatial memory and orientation.

The oil-paper insulation of high-frequency (HF) transformers frequently withstands high-frequency over-voltages at frequencies of several kHz and above. This leads to the occurrence of partial discharge (PD), which causes premature insulation failure in HF transformers. In order to investigate the effect of PD under high-frequency stresses on oil-impregnated Nomex paper, this paper analyzes the surface morphology, bond-broken types of the molecular chain, and product types formed for oil paper after PD degradation. Then, the damage mechanism of oil-immersed Nomex paper between high-frequency and AC stress is explored. The experimental results show that the branches of creepage do not exist in the oil-paper insulation during the entire discharge process under high-frequency stresses, and that their damage degree is higher than that of AC stress. This is mainly because the benzene ring of oil-impregnated Nomex paper is destroyed and opened caused by high-energy particles, the heating effect in HF discharge, and the bulk effect. These results help to improve the design theory of insulation structures and to develop PD-resistant insulation materials in HF transformers.

Nowadays, in the clinical, pharmaceutical, and environmental sectors, the development of facile and sensitive analytical methods and/or innovative devices for the follow-up and detection of antibiotics and pharmaceutical formulations, in general, are urgently needed and still challenging. This work declared three vital applications for broad-spectrum nitrofurantoin (macrofuran) antibiotic detection and quantification: A colorimetric method, a coated paper strip-based nano-lanthanum complex prototype and fabrication of smart electronic color sensor device-based coated paper strips. The colorimetric method showed a significant response upon increasing the concentration of the nitrofurantoin in a range between (1.0–100.0 ng/mL) via a visual color change from orange-yellow to red colors degree with detection and quantification limits of 0.175 and 0.53 ng/mL, respectively, whereas the nano-lanthanum complex coated paper strip prototype showed qualitative on-site sensing for nitrofurantoin via naked eye color changes which can be detected anywhere. Moreover, a smart prototype for detecting macrofuran in the means of paper color change in the RGB color component extraction algorithm and the grayscale projection value processing algorithm was fabricated. The change in RGB color on the coated paper strip was detected using an electronic color sensor device. The developed colorimetric method, coated paper strip, and the electronic color sensor device prototype exhibited fast, simple, costless, and selective towards macrofuran over the competing analyzed. As well as, showed good applicability in the different real samples spiked with different concentrations of macrofuran. Graphical abstract

Scientific writing is an important skill for a career as a professional astrophysicist. Very few researchers, however, receive any formal training in how to write scientific research papers of high quality in an efficient manner. This paper (Paper I) is the first of a two-part self-help guide in scientific writing to address this skills gap. Paper I focuses on planning your academic research paper in astronomy. We discuss how to crystallise the ideas that underlie a research project, analyse how the paper can be constructed considering the audience and the chosen journal, and give an overview of the publishing process. Paper II is a detailed description of the different sections that make up a research paper in astronomy and shares the best practice in how to write in English. Whether you are a student writing your first paper or an experienced author, you may find the ideas presented here useful., Comment: 15 pages; Paper I, submitted as a two-part series of Perspectives to Nature Astronomy. Kindly cite and/or acknowledge this work and Paper II (arXiv:2110.05503: 'How to write and develop your astronomy research paper' by Knapen, Chamba & Black) if you use them to plan and write your paper. Comments are very welcome! The Version of Record is available online at https://rdcu.be/cVdtK