Search

High per- and polyfluorinated alkyl substance (PFAS) concentrations have been detected in agricultural soils in Southwest Germany. Discharges of PFAS-contaminated paper sludge and compost are suspected to be the cause of the contamination. Perfluorinated carboxylic acids (PFCAs) have been detected also in groundwater, drinking water, and plants in this area. Recently, previously unknown compounds have been identified by high-resolution mass spectrometry (HRMS). Major contaminants were polyfluorinated dialkylated phosphate esters (diPAPs) and N-ethyl perfluorooctane sulfonamide ethanol–based phosphate diester (diSAmPAP). In this study, HRMS screening for PFAS was applied to 14 soil samples from the contaminated area and 14 impregnated paper samples which were from a similar period than the contamination. The paper samples were characterized by diPAPs (from 4:2/6:2 to 12:2/12:2), fluorotelomer mercapto alkyl phosphates (FTMAPs; 6:2/6:2 to 10:2/10:2), and diSAmPAP. In soil samples, diPAPs and their transformation products (TPs) were the major contaminants, but also FTMAPs, diSAmPAP, and their TPs occurred. The distribution patterns of the carbon chain lengths of the precursor PFAS in soil samples were shown to resemble those in paper samples. This supports the hypothesis that paper sludge is a major source of contamination. The presence of major degradation products like PFCAs, FTSAs, or PFOS and their distribution of carbon chain lengths indicate the activity of biotic or abiotic degradation processes and selective leaching processes from the upper soil horizons. Graphical abstract Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03463-9.

The potential of alkaline cellulo-xylanolytic enzymes from non-pathogenic Bacillus subtilis strain was tested for deinking of photocopier waste paper. Cellulase and xylanase play a crucial role in deinking of different types of waste paper. Partial purification of cellulo-xylanolytic enzymes was carried out using ultrafiltration followed by ammonium sulfate precipitation. The ultrafiltered enzyme was used for deinking the photocopier waste paper along with chemical deinking. An enzyme dose of 0.6 IU/g and reaction time of 60 min for ultrafiltered cellulo-xylanolytic enzyme significantly increased deinking efficiency, tear index (9.52%) and folding endurance (5±2%) as compared to chemical deinking. There was improvement in strength properties such as tear index and double-fold along with freeness of pulp (18%). There was slight decrease in tensile index (0.6%) and burst index (16%) while ISO brightness remained unaffected. Enzymatic deinking (74.3%) by ultrafiltered cellulo-xylanolytic from Bacillus subtilis was found significant over conventional chemical deinking.

The impact of volatile organic compounds (VOCs) and odor on indoor environment and people has attracted much attention. To reduce this problem of odorous compounds contained in wood panel, this study focused on identifying odorant compounds and exploring the influence of moisture content factors on VOCs and odor emissions. Paper mulberry (Broussonetia papyrifera (L.)Vent.) was investigated using the technology of gas chromatography-mass spectrometry/olfactory (GC–MS/O). Total volatile organic compounds (TVOC) and characteristic odor-active compounds were studied, and the emission of heartwood and sapwood of paper mulberry was compared at the same time. It was found that the main components from heartwood and sapwood were aromatics, alkanes, alkenes, aldehydes ketones, alcohols and esters. Totally, 23 kinds of odor-active compounds were identified from heartwood and sapwood of paper mulberry, among which, aromatics and aldehydes ketones were the main odorant compounds. Seven kinds of key odorant compounds were identified in this process. With the decrease in moisture content, the TVOC and total odor intensity of heartwood and sapwood generally decreased. The moisture content had a great effect on VOC release when the moisture content decreased from 70 to 50% and reduced from fiber saturation point (30%) to air saturation point (10%). The main odor impressions of paper mulberry were aromatic, fresh fruit fragrance, sweet scent and special pungent. In the whole process of moisture content decrease, the TVOC, concentration of odorant and odor intensity of sapwood were higher than that of heartwood.

Graphical abstract Enzyme-linked immunosorbent assay (ELISA) is widely used for the detection of disease biomarkers. However, it utilizes time-consuming procedures and expensive instruments, making it infeasible for point-of-care (POC) analysis especially in resource-limited settings. In this work, a multicolorimetric ELISA biosensor integrated on a paper/polymer hybrid microfluidic device was developed for rapid visual detection of disease biomarkers at point of care, without using costly equipment. This multicolormetric ELISA platform was built on multiple distinct color variants resulted from the catalytic oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) and the etching of gold nanorods (AuNRs). The vivid color changes could be easily distinguished by the naked eye, and their red mean values allowed quantitative biomarker detection, without using any sophisticated instruments. When this multicolorimetric ELISA was integrated on a paper/polymer hybrid analytical device, it not only provided integrated processing and high portability but also enabled fast assays in about 50 min due to the unique advantages of paper/polymer hybrid devices. The limit of detection of 9.1 ng/μL of the hepatitis C virus core antigen, a biomarker for hepatitis C, was achieved using this multicolorimetric ELISA platform. This multicolor ELISA analytical device provides a new versatile, user-friendly, affordable, and portable immunosensing platform with high potential for on-site detections of various viruses, proteins, and biomarkers for low-resource settings such as at home, public venues, rural areas, and developing nations. Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03359-8.

The study aimed at the use of char produced during pyrolysis of mix plastic waste. It further focused on producing activated carbon from char and also found its efficacy as efficient adsorbent for treatment of pulp and paper mill wastewater. The activated carbon was characterized in comparison with raw char for their physical, surface and adsorptive properties. Batch type adsorption experiments were carried out using 100 ml wastewater to observe the individual effectiveness using five different variables such as adsorbent dose (0.25–2.0 g), pH (6–10), time (5–24 h), agitation speed (100–200 rpm) and temperature (30–50 °C) by keeping other variables constant which helped to find out the effective range of all the variables. The competency was evaluated on the basis of colour and lignin content of pulp and paper industry wastewater. Once the effective range of different variables was identified, the statistical analysis was conducted to monitor the mutual impact on the reduction in colour and lignin contents in wastewater. From the statistical design applied, the best result was obtained at activated carbon dose (1.25 g), pH (8.0), contact time (7 h), agitation speed (184 rpm) and temperature (40 °C). The study resulted in reduction of 96.48% in colour and 94.25% in lignin at optimized condition in comparison with 87.37 and 80.44%, respectively, at unoptimized conditions. A potential increase in reduction of 9.0% in colour and 14.0% in lignin content was achieved after optimization through statistical design that confirmed its usefulness.

A simple electrochemical approach has been strategically developed for in situ generations of ZnO nanoparticles using Zn rods as electrodes and hydrogen peroxide as the oxidant without the formation of any by-product. These ZnO nanoparticles were extended for remediation of pollutants present in paper mill effluents, and separation efficiency was found to be above 90% for hydrocarbons, 92% for lignin, 99% for phenol, and 93% of chemical oxygen demand (COD), as confirmed by gas chromatography-mass spectrometry and COD analysis. It was also observed that the experimental setup could successfully remove 99% of the color from the sample. These ZnO nanoparticles have been proven in the past to be antibacterial and were explored for its ability to inhibit the growth of both Gram-positive and Gram-negative bacteria in the effluent samples after the removal of toxic pollutants. Therefore, we proposed an electrochemical reaction for the in situ synthesis of ZnO nanoparticles for remediation of paper mill effluent as well as inhibit the bacterial growth in the treated effluent sample.

Due to their unique properties, paper-based biosensors have attracted attention as inexpensive devices for on-site analysis. To achieve fast and sensitive detection of analytes, immobilization of enzymes with high apparent activities on paper is highly desirable; however, this is challenging. Herein, we report an improved approach to attach a malathion degrading enzyme, PoOPHM9, on paper via an interlocking network of Pluronic F127 (PF127)–poly(acrylic acid)–enzyme conjugates. The addition of PF127 improved retention of enzymatic activity as the apparent kinetic constant Vmax of the immobilized enzyme increased two-fold compared with the paper prepared without PF127. The PF127–poly(acrylic acid)–PoOPHM9 papers provided rapid colorimetric detection of malathion at 0.1–50 mM. The detection was completed within 5 min using a smartphone and image analysis software. As a proof-of-concept, malathion-contaminated water, plant, and apple samples were analyzed with the papers successfully. This material is promising for on-site rapid analysis of malathion-contaminated samples.

In this study, Taguchi experimental design was used to the optimize operating parameters for the degradation of paper mill effluent using electrochemical (EC) process with two-dimensional concentric aluminum tube electrodes (CATE). For this purpose, four significant experimental factors were used in four levels pH (6–9), electrolysis time (10–40 min), voltage (6–12 V) and surface area (357–624 cm(2)). The process parameters were optimized, through performing L16 orthogonal array of Taguchi technique, for the removal of chemical oxygen demand (COD) and turbidity. The percent COD and turbidity reductions were transferred into an accurate S/N ratio for a larger value is the better (LBT) response. The study presents a unique method of finding optimum combination of process parameters to illustrate their effect on the turbidity and COD reduction. The treatment conditions for the maximum elimination of the pollutants were second level of pH (7), third level of ET (30 min), fourth level of voltage (12 V) and second level of surface area (446 cm(2)). The confirmation experiment results were within the confidence intervals (CI) indicating an acceptable agreement between predicted and observed values. Based on the p-values, the electrolysis time and voltages were found to be the most significant factors for both COD and turbidity reduction. The findings of research indicated, that the Taguchi method can be used successfully for the treatment of paper industry effluent by electrochemical technique.

In this research, simultaneous quantification of cysteine (Cys) and histidine (His) using a paper-based sensor was investigated for the first time. A microfluidic paper-based sensor is a promising amino acid determination tool due to its low cost, low sample consumption, and fast analysis and is easy to make. We used SBA-15 as porous materials that are crystalline compounds formed with surfactants and TEOS as a silica source. The SBA-15 sample was characterized by X-ray diffraction, Fourier transform infrared, and scanning electron microscope techniques. The microfluidic paper-based sensors were fabricated using a wax pen, and the mesoporous SBA-15 modified filter paper. The fabricated sensors for Cys and His determination are operated based on an indicator-displacement assay. A comparative determination study of Cys and His on the sensors was carried out. The results illustrated that the addition of silica nanoporous material led to an immediate and uniform color change. The sensors were successfully exploited in the simultaneous determination of urinary Cys and His levels, thus providing the potential opportunity for clinical diagnosis. The linear range of 1.0 to 90.0 μM and 1.0 to 100 μM for His and Cys was obtained from the calibration data. The detection limits were also calculated (S/N = 3) for His and Cys of 0.5 μM and 1.5 μM, respectively. The proposed method showed a good agreement with the results achieved by a standard method.

This study focused on the applying endo-xylanases to reduce the use of bleaching agent, coupled with the production of xylooligosaccharides (XOs), in mulberry paper making. Paper mulberry pulp (PMP) was consecutively prepared from paper mulberry bark by traditional NaOH-treatment, and two types of thermostable endo-xylanase from Streptomyces thermovulgaris TISTR1948 (wild-type and recombinant endo-xylanases) were employed in the biobleaching of PMP. This process was optimized to achieve maximum XOs yields and the highest PMP quality. The optimal condition was an enzyme dosage of 125 U/g PMP at 12 h of reaction time, both in a 500 mL laboratory bottle and a 150 L reactor. The mixture obtained from the reactor was separated as liquid of XOs derived from PMP (PMP-XOs) and solid biobleached PMP. The PMP-XOs from wild-type endo-xylanase were composed of 31.6% xylopentaose (X5), 30.9% xylohexaose and higher-degree XOs (X ≥ 6), and 11.7% xylobiose (X2), whereas 76.6% of X5 and 8.6% of X2 were the main products from recombinant endo-xylanase. The PMP-XOs derived from both endo-xylanase types exhibited high antioxidant activities, reducing power, phenolic contents, and prebiotic efficacy. In addition, the application of both endo-xylanases enhanced the brightness of PMP by 5.1% and 3.5%, and reduced the kappa number by 9.1% and 3.6%, respectively. Biobleached PMP was subsequently subjected to the NaOCl bleaching step to produce the mulberry paper. This approach could reduce NaOCl consumption by 20–25%, making it an environmentally friendly alternative. The production of valuable prebiotics, such as PMP-XOs, further enhances the economic viability of this approach.

A high-barrier, strong, and antibacterial paper was fabricated by coating the acetylated cellulose solution with different contents of cinnamaldehyde (CIN) on Kraft paper. The antibacterial, antioxidant, mechanical, and barrier properties of coated paper were investigated. When the amount of CIN added in coating reached 6% v/v, the coated paper exhibited excellent antioxidant activity and antibacterial activity against Escherichia coli and Staphylococcus aureus. Notably, the dry and wet tensile strength of paper after coating was increased by 26.4 and 10.6 MPa, respectively. Furthermore, the coated papers' barrier properties against oil, water, water vapor, and oxygen were dramatically improved, especially for the water barrier rate up to 96.4%. Our coated papers with over 6% v/v CIN could extend beef's shelf-life for at least 4 days, which exhibited a promising prospect in eco-friendly antibacterial packaging.

Synthetic cannabinoid receptor agonists (SCRAs) are a class of varied compounds that mimic the effects of natural cannabinoids found in cannabis. Because they have a wide range of diverse structures, they vary widely in their potency. The abuse of new psychoactive substances (NPS) in prisons was reported in many European countries and in the USA. In the present study, we have described the identification of SCRAs in 56 infused paper sheet samples, seized mainly in Brazilian prisons between 2016 and 2020. The materials were seized by local or federal law enforcement and analyzed by Sao Paulo State Police or Brazilian Federal Police using gas chromatography–mass spectrometry, attenuated total reflection-Fourier transform infrared spectroscopy, liquid chromatography–high-resolution mass spectrometry or nuclear magnetic resonance spectrometry. Most of these samples (87.5%) were seized in 2019–2020; seven different SCRAs were identified in samples, and the most frequently identified substances were MDMB-4en-PINACA (23.6%) and 5F-MDMB-PICA (36.4%), the newest SCRAs emerging recently. As observed in Europe and the USA, Brazil also shows the prevalence of indazole-3-carboxamides and indole-3-carboxamides among SCRAs seizures in the prison system. This phenomenon is spreading all over the world at this moment. These data on the prevalence could help to alert judicial authorities to shutting down the introduction of NPS, including SCRAs, into prisons to ensure safety and security for avoiding health risks of prisoners and staff, leading to positive effects in this population. To our knowledge, this is the first demonstration of SCRAs smuggling into prisons in Latin America.

The salivary glands are closely associated with stress conditions and the neuroendocrine system. The concentrations of these salivary biomarkers fluctuate with a person’s disease status. Until now, salivary diagnostics have been promising; however, the analytical tools for detecting salivary biomarkers have remained burdensome due to the lack of user-friendly and cost-effective equipment. In this study, we used a microfluidic starch-coated paper-based chip to isolate ɑ-amylase from human saliva. The concentration of ɑ-amylase on the head and tail sections of the paper-based chip was compared in the presence or absence of starch. We found that ɑ-amylase was highly concentrated only in the head section of the starch-coated paper-based chip through Western blotting (WB) and enzyme-linked immunosorbent assay (ELISA). We expect our designed paper-based chip will aid in α-amylase detection technologies using saliva and small amounts of other biofluids including blood, tears, pancreatic juice, and urine.

Organic dyes are used in many industries, e.g., textile, cosmetics and food. Hence, contamination of organic dyes to water sources is a critical issue. To reduce water pollution by organic dyes, we propose a paper-like adsorbent with a practical and economical production procedure. Subsequently, a flexible adsorbent was produced using a one-step approach by vacuum filtration of graphene oxide (GO) and iron oxide nanoparticles (Fe3O4-NPs) containing dispersion through a membrane and quoted as GO/Fe3O4 paper. For comparison, GO paper was also prepared using the same procedure. Both papers were characterized using UV–VIS absorption spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, electron diffraction X-ray analysis, X-ray photoelectron spectroscopy, and powder X-ray diffraction techniques. At the steady-state conditions, GO/Fe3O4 and GO papers were performed as adsorbent for cationic dyes of methylene blue, neutral red, and anionic dyes of methyl orange and fluorescein. In general, the removal efficiency of GO/Fe3O4 paper was higher than that of GO paper for adsorption of all dyes and this adsorbent revealed satisfactory adsorption properties for cationic dyes when compared to anionic dyes.

In this elucidation, we synthesized novel molecularly imprinted polymers (MIPOH1-4) that were used as organic fillers on bagasse pulp to form cellulosic paper sheets, the formation of MIPOH1-4 from the reaction of enaminone 3 with methyl methacrylate monomer in the presence of ethylene glycol dimethyl acrylate and 2,2’-azobisisobutyronitrile. The obtained MIPOH1-4 was confirmed via FT-IR and SEM with different pore sizes. And we noticed that the increase of template 3 increases the hydrogen bond between monomer and template and gave sponge surface of MIPOH4. Furthermore, the computational energies of the template with different monomers utilize DFT/B3LYP/6-31G (d) level to know the stability of polymers and hydrogen bonding between them. So that we applied that in paper manufacture through the adsorption of MIPOH4 as an organic filler on bagasse pulp to form novel cellulosic paper sheets with different concentrations and these sheets which characteristic through FT-IR, SEM, sizing test, tensile strength, and elucidation their antimicrobial activity with theoretical and docking studies. The MIPOH4 and cellulosic paper sheets showed the thermal stability and high tendency of sizability of these paper sheets and concluded the interaction between cellulose fibers of pulp with MIPOH polymer with physical hydrogen bonding.

This paper is aimed to develop a hybrid model (PCA-ANN) to predict the extractive content in eucalyptus wood clones. The input variables to the virtual analyzer are planting parameters available from the forest inventory, therefore the prediction does not rely on laboratory analysis of the wood samples, affording a quick estimate of the extractive contents. This study further bridges the literature gap on the investigation of the cause of variability of extractive content in eucalyptus wood. The PCA-ANN was identified from experimental data to predict and monitor the extractive content, since laboratory measurements can take several days and become available only after wood processing. The experimental data contained information on ten species of eucalyptus clones from five regions in the extreme south of Bahia, Brazil. Principal Component Analysis (PCA) firstly assessed the impact of planting variables on the extractives content. The variability of the data was represented by eight principal components and the variables that mostly contribute to the extractive content are: potential acidity, iron, saturation of aluminum, magnesium, pH, base saturation, remaining phosphorus, zinc, manganese and copper. The artificial neural network (ANN) with the 8 principal components in the input layer showed that the PCA could effectively reduce the dimensionality of the data. For practical purposes, though, the ANN with 10 input variables and 16 neurons in the hidden layer, presenting an average relative deviation of 1.5%, is recommended. The prediction of the extractive content is essential to allow preventive management practices toward the improvement of yield and quality of the cellulosic pulp.

Microfluidic paper-based analytical devices (μPADs) have developed rapidly in recent years, because of their advantages, such as small sample volume, rapid detection rates, low cost, and portability. Due to these characteristics, they can be used for in vitro diagnostics in the laboratory, or in the field, for a variety of applications, including food evaluation, disease screening, environmental monitoring, and drug testing. This review will present various detection methods employed by μPADs and their respective applications for the detection of target analytes. These include colorimetry, electrochemistry, chemiluminescence (CL), electrochemiluminescence (ECL), and fluorescence-based methodologies. At the same time, the choice of labeling material and the design of microfluidic channels are also important for detection results. The construction of novel nanocomponents and different smart structures of paper-based devices have improved the performance of μPADs and we will also highlight some of these in this manuscript. Additionally, some key challenges and future prospects for the use of μPADs are briefly discussed.

Thermochemical parameters of A4-sized printing paper (AP), filter paper (FP), newspaper (NP), writing paper (WP), and reed pith (RP) samples were estimated using standard protocol to identify its fuel characteristics, and thermal degradation of the same was studied using thermogravimetric analysis (TGA) and differential thermogravimetric (DTG) techniques in the temperature range of 30–800 °C at the heating rates of 10, 15, and 20 °C/min under nitrogen atmosphere. The curves of TGA and DTG exhibited four significant stages. Maximum weight loss was found to be in the second stage. Kinetic analysis was carried out in the conversion range of 0.1 to 0.7 using iso-conversational models of Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), Vyazovkin, and Vyazovkin AIC (V.AIC). The average activation energies were found to be 139.90, 115.93, 212.52, 257.41, and 241.63 kJ/mol using FWO; 129.73, 103.06, 202.46, 248.38, and 231.55 kJ/mol using KAS; 145.57, 134.00, 195.29, 256, and 241.63 kJ/mol using Vyazovkin; and 140.71, 133.86, 193.14, 247.57, and 190.14 kJ/mol using Vyazovkin AIC model. Thermodynamic parameters (enthalpy change (ΔH), Gibbs free energy change (ΔG), and entropy change (ΔS)) using these models have been evaluated.

All-cellulose paper-based composites with underwater superoleophobicity and high-wet-strength were developed by casting a barrier layer of bacterial cellulose (BC) on a filter paper substrate. To optimize the pore structure of barrier layer, slow gel process of BC dispersion was conducted via acidification and solvent exchange. 1,2,3,4-butanetetracarboxylic acid was used to improve the wet strength and surface hydrophilicity through the crosslinking reaction between fibers. The underwater oil contact angles are higher than 150° in neutral environment, and slightly decrease under acid and alkali conditions. Combined with the micron-sized pore structure of BC barrier layer, the composite papers show good separation performance of oil-in-water emulsion. A denser BC layer can significantly improve the separation efficiency, but also lead to the reduction of flux. During the gelation of BC barrier layer, the increase in the ethanol/water ratio of the dispersion medium is able to increase the flux without obvious negative impact on the separation efficiency. When the ethanol/water ratio is 80%, the separation efficiency and water flux reach 99.2% and 1320 L m−2 h−1·bar−1 for the emulsified soybean oil with the average size of 13 μm, respectively. This type of all-cellulose composite papers provides a new idea for the fabrication of membrane materials for oil–water separation.

Currently, most of the collected waste medium-density fiberboards (MDF) is incinerated or landfilled, as economically viable recycling methods are yet to be developed. By steam refining waste medium-density fiberboards (MDF), it is possible to hydrolyze the incorporated resins and isolate a high yield fiber fraction. Further refining of the steam treated fibers might enable the fibers to be utilized in applications such as paper packaging, facilitating a cascading use of the waste material stream. To this end, intimate knowledge of the material is needed. In this study, the steam refined fibers of two waste MDF samples containing differing amounts of softwood and hardwood underwent refining and beating. The resulting fibers were characterized regarding their morphology and paper test sheets were produced to evaluate their strength (compression-, tensile- and tear-strength). Distinct differences in response to refining between the MDF samples were apparent. For the sample with the higher hardwood share an increase in strength properties with increasing steam treatment severities could be observed and it was possible to produce test sheets with comparable compression strength to recycled pulp for industrial corrugated paperboard. For the sample with a higher share of softwood, the steam treatment severity did not show any influence on fiber morphology or paper properties, and the resulting paper strength was low in comparison to the other steam refined waste MDF sample. Graphic Abstract

The kapok (Ceibapentandra (L.) Gaertn) seed fibre is unicellular with length up to 35 mm, however, it is covered by a hydrophobic waxy layer that limits its application in paper production. In this study, the effect of various pulping methods namely mechanical, chemi-mechanical, semichemical and chemical pulping on kapok fibre properties was investigated. Each kapok pulp was then blended with the secondary fibre recovered from kraftliner board for handsheet making to examine their reinforcing ability on strength properties. The results showed that kapok mechanical pulps (with and without dewaxing (5% (v/v) diluted detergent) and chemimechanical pulp were unable to improve the strength properties of the handsheet. Kapok pulps chemically treated with 18–25% of sodium hydroxide gave a better effect on handsheet strength properties whilst fibre treated with 20% sodium hydroxide showing the highest increment. Although the reinforcing effect of the 4% native cooked starch was slightly higher than that of the 10% kapok pulp blended in recycled paper, the recycling potential of the latter was better as all strength properties retained unchanged after recycling. The findings indicated that kapok chemical pulp is a promising reinforcing fibre source with superior recycling potential.

The uses of natural dyes are getting popularized due to the increased awareness regarding the toxicity of many chemical colorants. The chemical colorants are being replaced by the natural colorants for the various industrial applications. The plant-based natural colorants are considered eco-friendly and toxic free. In the present study, we report a natural dye from the heartwood of Caesalpinia sappan suitable for paper based packing materials. This forms the first report on the study of natural dye obtained from the heartwood of C. sappan on paper material. The extracted dye had a good photostability and able to make imprints on recycled paper bags. Moreover, a significant inhibition of bacterial growth was observed at a higher dye concentration of 100 μg mL−1 against P. aeruginosa which was higher than the standard antibiotics. Growth inhibition was also observed in case of B. subtilis (22 ± 0.17 mm) and K. pneumonia (21 ± 0.53 mm) at 100 μg mL−1. The dye could be used in making medicated packing materials and have many other bio-potential which was validated through in silico toxicity analysis. The application of such natural dyes in paper material value addition will help in a cleaner and sustainable process during paper recycling.

In traditional deinking process, large amounts of chemicals are required which makes these methods expensive and polluting. Also, application of sustainable material implies the use of green processes to reduce waste and pollution. Green enzymatic deinking processes are alternatives to those technologies that have negative effects on the environment. In this work, we applied response surface methodology for deinking the electrophotography-printed paper based on a systematic experimental pattern. The individual and interactive effects of enzymatic deinking parameters including time, temperature, and enzyme dosage on the handsheet properties were investigated. Different analyses were carried out to determine the best process conditions of enzymatic deinking to optimize the handsheet properties (i.e., tensile, burst, whiteness, and brightness). The obtained responses of an oven-dried fiber at 45 min, 43 °C and the enzyme concentration of 1 mg/15 g were 12.44, 0.65, 72.20, and 87 for tensile strength, burst strength, whiteness, and brightness, respectively. Measuring the optical density of the deinked handset after printing showed that the printability of the deinked paper is in the desired range.

Rising socioeconomic level and increasing popularity of e-commerce have dramatically increased the use of cardboard packaging materials, and consequent related recycling and wastes. Large amounts of sludge (up to 40% of input mass) is formed through the recycling process, with sludge solids that are very rich in cellulose fibers (~ 75% w/w). To date this sludge is mostly disposed in landfills, resulting in added economic and environmental costs to the recycling process. Short ozonation pretreatment of RPS resulted in enzymatic release of ~ 34% of the cellulosic fraction of the sludge as sugar, and fermentation of these sugars by yeasts resulted in production of ~ 15 g/L ethanol. The solid remnants, were used as a bio-sorbent, efficiently removing dyes from textile wastewater. Recycled paper sludge waste was thus a good source for both energy and water-treatment applications, increasing sustainability and circular economy in the paper and cardboard recycling industry.

This study evaluates the use of fermentation to increase nutrient availability in pulp and paper bio-sludge (PPBS) as feed for black soldier fly larvae (BSFL). Rearing of BSFL on fermented PPBS was carried out in a climate chamber in order to assess nutrient availability and larvae survival and growth. The PPBS used came from a chemo-thermomechanical pulp/groundwood pulp mill. The PPBS was fermented at 35 °C and 55 °C, respectively, at initial pH of 10. The effects of sediment and liquid from fermented PPBS on larvae dry weight, survival rate until the prepupae stage, bioconversion, and reduction rate of PPBS were measured. The bioconversion of the liquids (4.1–6.6%) was substantially higher than for both the sediments and untreated PPBS (≤ 0.4%). The survival rate, on the other hand, was substantially lower (26.3–30.9 %) than for the sediments and untreated PPBS (49.5–52.6%). Neither the sediments nor the liquids had significant effects on the larvae weight or on the PPBS reduction rate. The sediments had no significant effect on the survival rate or the bioconversion. This study demonstrates that fermentation dissolves a part of the PPBS and that dissolved substances in the fermentation liquid readily convert to larvae biomass. However, the bulk of the lignocellulose is not dissolved, and most of PPBS nutrients remain unavailable for growth of the larvae. Further research should focus on improved pretreatment of PPBS to increase availability of nutrients and thereby improve the feasibility of BSFL as a recycling method for PPBS.

The objective of this study was to check the potential of crude xylano-pectinolytic enzymes in bleaching of rice straw pulp, in order to reduce the toxic waste load for managing the environmental pollution. The xylano-pectinolytic enzymatic bleaching step for delignification was found to be most effective at pulp consistency 1:10 g/ml, xylanase:pectinase dose of 9:4 IU/ml, pH 8.5 and treatment time 180 min at temperature of 55 °C, and resulted in lowering of kappa number of the rice straw pulp by 15.29%. In subsequent bleaching stages, this enzymatic pre-bleaching treatment also resulted in 30% reduction of active chlorine dioxide dose without any loss of optical properties. Significant improvement in various physical properties of the enzymes treated pulp, tear index (15.43%), breaking length (11.11%), double fold number (25.92%), burst index (9.88%) and viscosity (13.63%), and Gurley porosity (39.86%) was also noticed. This approach resulted in reduction of BOD and COD values by 21.07% and 26.57%, respectively. This is the first study on the use of crude xylano-pectinolytic enzymes for bio-bleaching of rice straw pulp.

A paper-based membrane coated by graphitic carbon nitride (g-C3N4) is prepared via a dip-coating method and used as a separator for sodium metal batteries with merits of low cost and environment-friendliness. Introduction of g-C3N4 effectively improves the ionic conductivity and the structural stability of the separator. Compared with traditional polyethylene separators and Al2O3-coated separators, the g-C3N4-coated separators show better electrolyte wettability, thermal stability, and electrochemical stability. Therefore, Na||Na3V2(PO4)3 battery using the g-C3N4-coated separator exhibits better cycling stability and higher rate capability. These results prove that the g-C3N4-coated paper-based separator is expected to become the next generation of low-cost and high-safety separator in sodium metal batteries.

The present study illustrates the electrocoagulation remediation of paper mill wastewater for multiple response optimization. Multiple response optimization can be combined into one desirability function. All variables and responses varied for a unique global solution. The effect of basic electrocoagulation process variables pH (3–10), conductivity (3.15–10 mS/cm), electrode distance (1–2.5 cm) and current density (5–20 mA/cm2) on four response parameters such as chemical oxygen demand, color, total dissolved solids and total organic carbon has been analyzed experimentally and statistically. The global solution for these variables and responses obtained by software over a hundred design points. For unit desirability function variables conditions were pH 7.49, Conductivity 8.34 mS/cm, electrode distance 2.06 cm and current density 9.32 mA/cm2. In these global variable conditions, responses were observed to be COD 70.19%, Color 75.03%, TDS 70.69% and TOC 71.93%, respectively.

This study investigated the feasibility of utilizing paper sludge (PS) as feedstock in the production of composite boards that are lightweight, durable and environmentally friendly. PS samples were collected from recycled newsprint (RN), corrugated recycled (CR) and virgin pulp (VP) pulping mills in South Africa. The PS was dried and mixed with magnesium phosphate cement to produce boards in a central composite design. Three different fillers including fly ash, calcium carbonate and silica fume were also added to the mix as binder replacement. The PS was characterized before use, and the produced composite board was evaluated for mechanical and physical properties. The boards produced had medium to high density (0.52—1.12 g/cm3) that could be used for non-structural interior applications. The results showed that boards containing RN had the highest mean value for modulus of elasticity (MOE) of 769 MPa. The mean MOE for boards containing CR- and VP-PS was 357 and 411 MPa, respectively. Calcium carbonate had the best effect on the board properties. Techno-economic analysis was simulated for four different types of feedstock scenarios at different locations including a combined scenario. Sensitivity analysis revealed that decreased feedstock cost resulted in decreased minimum required selling price. The analysis also revealed that the combined scenario proved to be the most cost-effective and profitable option for the future.

Compared with a single chemical indicator, the use of multivariate chemical indicators in aging status assessment of transformer cellulose paper insulation can improve the reliability of the evaluation. In this study, a non-destructive method based on multivariate chemical indicators was proposed to evaluate the remaining life of cellulosic paper insulation. The selected chemical indicators closely related to the aging of the insulating paper were analyzed. Additionally, by applying the subjective and objective weighting method, the evaluation information of each indicator was fully extracted to obtain reasonable comprehensive evaluation weights. Besides, the comprehensive evaluation index of multivariate chemical indicators was obtained by using the technique for order preference by similarity to ideal solution method, which is consistent with the deterioration law of paper insulation. Then, the correlation lifespan model between the comprehensive evaluation index of multivariate chemical indicators and the degree of polymerization of insulating paper under different aging stages was established. The effectiveness of the proposed model was verified by experiments. This promising model can increase the accuracy of the condition assessment for the transformer cellulosic paper insulation.

Anaerobic co-digestion of sludge from recycled pulp and paper industry (RPPS) with vinasse effluent from alcohol distilleries (VW) was performed under mesophilic conditions (37 °C) at laboratory scale, using one-liter continuous stirred tank reactors (CSTRs). The physicochemical parameters were monitored during the process. The average pH and alkalinity were 7.7 and 1000 mg CaCO3 Kg−1, respectively, indicating that the process is working well without the risk of acidification. The methane yield and biodegradability of this mixture were determined. The methane yield was about 112 (NmL CH4 g−1 VS added) and biodegradability reached 73%. Nevertheless, in monodigestion of RPPS, the methane yield was 94 (NmL CH4 g−1 VS added) and biodegradability 65%. The anaerobic co-digestion of (RPPS) with (VW) at a proportion of (70:30) improved methane production by 16% and biodegradability by 11%. Bioenergy recovery from industrial (RPPS) is promoted by co-digestion with (VW), and the removal efficiency of 73% indicates the performance of the process adopted. A kinetic study was performed using five models Richards, modified Gompertz, Logistic, Cone, and first order. The results show that Richards' was the most appropriate model for adjusting methane production from (RPPS) and (VW) co-digestion.

Gelatine sizing was used extensively for western papermaking before the nineteenth century and this technique is still applied nowadays for restoration purposes. Despite its wide use, the relationships between gelatine types, the strength of the size and its distribution inside the paper sheet are still unclear. Different concentrations of three gelatines of various origins and types (A/B) were used to size model papers. The gelatine uptake, the strength of the size and the presence of gelatine at the papers surface were investigated by using a water drop test method and ATR-FTIR spectroscopy. At a given concentration, similar uptakes were found for all gelatines but great variations were observed in terms of size strength and of gelatine ability to cover the surface of paper sheets. In addition, Scanning transmission X-ray microscopy was performed on paper fibres cross sections to map the distribution of the organic compounds (both cellulosic and proteinaceous) on a nanometer scale. This showed that gelatine coats but does not penetrate the fibres. It can be inferred that the different size strengths observed between the tested gelatines are mainly due to different ways of filling holes between fibres inside the paper mat, some gelatines being more prone to go inside the sheet than others which remain mostly distributed near the surface.

Natural cellulose paper is flame retarded using ammonium polyphosphate/montmorillonite (APP/MMT) nanocompound through coating method. Their morphologies are assessed by scanning electron microscopy, chemical components by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, chemical structure by Fourier transform infrared, thermal stability by thermo-gravimetric analysis and fire retardancy by 45° horizontal burning test. The results show that the thermal stability and flame retardancy of coated paper samples are enhanced obviously, and all samples are self-extinguishing during the tests due to the char formation reaction between APP/MMT and cellulose. Then the treated paper, AM-18.3, as surface flame retardant treatment for low specific surface area (SSA) polypropylene (PP) specimens (PP@AM-18.3) also is investigated using cone calorimeter. Compared with two controlled samples, PP@AM-18.3 shows significantly increased time to ignition, the lowest fire growth index and highest fire performance index. This may give a new flame retarded approach for low SSA polymer materials with little amount flame retardants.

Whether the caste fate of social insects is determined before or after emergence is a key question for understanding the evolution of eusociality. Paper wasps are a suitable model for answering this question because there are no critical morphological differences between queens and workers in paper wasps, and these animals appear to represent an early stage of eusociality. We explored the above question by determining the effects of photoperiod during the adult stage on caste-fate determination in the paper wasp Polistes jokahamae. We collected colonies at different stages in the field and exposed emerging adults individually to long or short days. Under these isolated conditions, gyne-destined (diapausing) females were expected to exhibit large lipid stores without mature eggs, while the reverse was expected to be true for worker-destined (nondiapausing) females. The proportion of wasps with mature eggs was higher under long days in the second and subsequent broods, but not in the first brood. Lipid stores were larger among large females and under short days, and smaller for the first brood. These findings together suggest that the first brood emerges with a strong preimaginal bias toward workers (nondiapausing form), whereas the other broods emerge with no bias or an easily reversible bias. However, it is difficult to conclude whether the bias came from body size or the season of emergence. We discuss the possibility that the ancestor of paper wasps had workers with and without preimaginal bias toward becoming workers at emergence.

Lightweight yet strong paper with high toughness is desirable especially for impact protection. Herein we demonstrated electrically conductive and mechanically robust paper (AP/PB-GP) made of reduced graphene oxide via interfacial crosslinking with 1-aminopyrene (AP) and 1-pyrenebutyrat (PB) small molecules. The AP/PB-GP with thickness of over ten micrometer delivers a record-high toughness (∼69.67 ± 15.3 MJ m−3 in average), simultaneously with superior strength (close to 1 GPa), allowing an impressive specific penetration energy absorption (∼0.17 MJ kg−1) at high impact velocities when used for ballistic impact protection. Detailed interfacial and structural analysis reveals that the reinforcement is synergistically determined by π-π interaction and H-bonding linkage between adjacent graphene lamellae. Especially, the defective pores within the graphene platelets benefit the favorable adsorption of the pyrene-containing molecules, which imperatively maximizes the interfacial binding, facilitating deflecting crack and plastic deformation under loading. Density functional theory simulation suggests that the coupling between the polar functional groups, e.g., −COOH, at the edges of graphene platelets and −NH2 and −COOH of AP/PB are critical to the formation of hydrogen bonding network.

In China, Xuan paper has been the paper of choice as artwork support and for conservation, for several centuries. However, little is known about its material properties, especially given the many grades of sized and unsized Xuan paper. In addition, there is a lack of information on its degradation. In this research, a selection of contemporary unsized Xuan papers was investigated, representing diverse raw materials. Seven out of twelve contemporary unsized Xuan papers were determined to be approximately neutral and contain > 2% alkaline reserve, indicating good durability. Viscometry was used to determine the degree of polymerisation (DP) as none of the samples gave significant reactions to the phloroglucinol spot test. The average DP of ten contemporary unsized Xuan papers is ~ 1700, excluding two papers that have presumably been sun-bleached, and that exhibit significantly lower DP. Using X-ray fluorescence, it can be demonstrated that Ca and Si are the dominant elements and interestingly, Ca content is directly correlated with ash content and with alkaline reserve. Accelerated degradation was performed at two sets of environmental conditions, i.e. 90 °C, 30% RH and 60 °C, 70% RH, and the established degradation rates agreed with the Collections Demography model of paper degradation meaning that degradation of Xuan papers proceeds in the same way as other types of paper. This research gives fundamental insights into contemporary unsized Xuan papers, which exhibit good stability during accelerated degradation despite the low starting DP in the context of the samples used in this study. Our findings may inform methods of Xuan paper production, selection of Xuan paper for conservation purposes, as well as preventive conservation of Xuan paper-based artefacts.

Process-monitoring laboratories in the pulp and paper industry generally use a combination of wet chemical analyses and physical measurements to certify the fitness of a production pulp for a specific end-use. These laboratory tests require time and the effort of trained personnel, limiting their utility for real-time process control. Here we show that Raman probes of unrefined cellulosic pulps, well-suited to the online measurement of in-process materials, can predict the quality attributes of manufactured papers. The accuracy of prediction improves when the covariance is modelled in a reduced measurement space selected by a data-driven, feature-selection technique referred to as a Template Oriented Genetic Algorithm (TOGA). TOGA, combined with discrete wavelet transform (DWT), isolates functional-group features that correlate best with mechanical properties paper derived from refined pulp. Paper makers refine market pulps to build sheet strength using a beating process that decreases freeness as it increases fibre-fibre bonding. Methods demonstrated here predict manufactured sheet properties obtainable after any specified degree of refining from the Raman spectrum of an unrefined pulp. This analysis capacity will enable both vendors of market pulp and makers of sheet paper to specify in advance the amount of beating required to produce a desired product, thereby saving cost and conserving resources.

An industry compatible chemo-refining approach was tested for preparation of micro-nanofibrillated cellulose (MNFC) from bleached softwood pulp using sodium meta-periodate and sodium chlorite as oxidizers followed by refining in Valley beater. SEM and FTIR analyses confirmed micro-nano scale fibrillation and chemical functional group modification in laboratory prepared MNFC, respectively. The water retention value, carboxyl content and viscosity of MNFC were found comparable with imported NFC as reference (R-NFC). To evaluate MNFC as strength enhancer for paper properties, 5% MNFC addition to bleached mixed hardwood pulp showed 6% reduction in bulk with 36%, 24% and 97% increment in breaking length, burst index and double fold of the handsheets, respectively without affecting tear index and optical properties than the control. Surface properties were also improved. Pulp drainability (37°SR) after MNFC addition was found suitable for papermaking. These laboratory results confirmed the potential of MNFC as a suitable strength additive for paper quality improvement.

In this study, a microfluidic paper-based analytical device (mu PAD) was integrated with a smartphone app capable of offline (without internet access) image processing and analysis for the rapid colorimetric detection of glucose. A self-inking stamp was used to form hydrophobic channels on a piece of paper-towel due to its superior water absorption efficiency. As demonstrated, the developed sensor was employed for the colorimetric detection of glucose in artificial saliva in the linear scope of 0 - 1 mM with a calculated detection limit of 29.65 mu M. The experimental results show that the quantitative analysis of glucose with the proposed smartphone platform could be completed in less than one minute. The app developed for the smartphone platform is capable of extracting the color-changing area with an embedded image processing tool which could address the problem of color uniformity in the detection zones of mu PAD. The integrated platform has great potential to be used for non-invasive measurements of glucose in body fluids, like tears, sweat and saliva.

In this study, the synthesis of the {001} facet of anatase TiO2 (T-{001}) was hydrothermally carried out by a two-step process (without using fluoride ions as capping agent); the synthesized T-{001} sample was characterized by XRD, FESEM and HRTEM. The T-{001} was used for improvement in biodegradability of paper mill wastewater in the batch and continuous system under UV light irradiation. The performance of T-{001} was compared to commercial TiO2 (P25). In the batch system, the effect of the pH, time and photocatalyst dosage on the COD removal were investigated. The results showed that alkaline condition enhanced photocatalytic degradation of COD. For batch system, biodegradability index (BOD5/COD ratio) improved from 0.12 to 0.71 by application of the T-{001}; whereas this improvement was 0.52 for P25 sample. For the continuous system, the TiO2 samples were immobilized on the glass media and utilized in a packed bed photoreactor (PBPR). The effect of different flowrates on the COD removal was investigated. To investigate the stability of the samples, the photocatalytic experiments were continuously carried out for 3 h; both samples showed considerable stability during this time. The final values of BOD5/COD ratio at flowrate of the 5.4 ml/min were 0.64 and 0.42 for CT-{001} and CP25, respectively.

Maturity of vermicomposted end products obtained from citronella bagasse (CB) and a mixture of citronella bagasse and paper mill sludge (CB + PMS) was determined employing the epigeic earthworm species Eisenia fetida. Two of the primary biological indicators—enzyme assay and germination index—were used for evaluation of vermicompost maturity. The enzyme assay includes the changes in dehydrogenase and urease activities in the final products. The test for germination index was performed on two economically important plant species Abelmoschus esculentus and Solanum melongena. The results revealed a significant increase in dehydrogenase and urease activities in the vermicompost samples over the raw materials and traditional compost. The enhancement was recorded 215.63–225.63% in dehydrogenase and 149.89–249.31% for urease in the end products obtained after 45 days of experimental trials. Further, the higher values of germination index in the vermicompost treatments as against the control confirm the suitability and stability of the vermicomposted final products.

The search for non-wood fibers as alternative to the limited wood fiber resources is highly imperative in the pulp and paper-based industries. This is due to growing environmental concern as a result of excessive deforestation. This study aimed at investigating the pulp and paper potentials of pineapple crown (Ananas comosus), sandbox (Hura crepitans), pino macho (Pinus caribaea), elephant grass (Pennissetum purpureum) and teak (Tectona grandis) leaves. Chemical properties (holocellulose, cellulose, hemicellulose, ash contents, hot water and 1% NaOH solubilities) were determined using the relevant TAPPI test and chlorite methods, while the physical properties were determined after the pulping processes. Fourier transform-infrared spectroscopic (FT-IR) analyses of intrinsic functional groups of the paper sheets produced from the pulps of the waste plant leaves were determined. In addition, scanning electron microscope (SEM-EDX) analyses of the morphological characteristic and elemental compositions of the resulting hand sheet surfaces were also examined. P. caribaea has the highest lignin (80.22 ± 0.012%) and cellulose (72.30 ± 0.012%) contents with lowest 1% NaOH solubility (15.20 ± 0.05%) values. A .comosus has the highest hemicellulose (21.73 ± 0.1%) and moisture (75.00 ± 0.12%) contents with lowest ash values (5.01 ± 0.15%). The fibre lengths and the Runkel ratio of the resulting pulps were of the order, A. comosus > P. purpureum > P. caribaea > H. crepitans > T. grandis and A. comosus

Reproductive conflicts are expected in societies where nonbreeding helpers retain the ability to produce offspring. Despite potential competition from reproductively capable nestmates in social wasps, egg laying tends to be monopolised by a single or relatively few queens. Genetic studies on reproductive partitioning in Polistes paper wasps suggest high reproductive skew in the genus. Conflict is thought to be minimal due to nestmate relatedness or the possibility of inheriting a reproductive monopoly on a nest; consequently, there are inclusive fitness opportunities for nonreproductive helpers. However, most studies are limited to temperate wasp species. Given the cosmopolitan distribution of Polistes, genetic data on group conflicts are required for a broader range of tropical species to determine whether these trends apply across climatic zones. We examined female reproductive skew in the Neotropical paper wasp Polistes lanio, genotyping a selection of adults and pupae from established post-emergence nests using single-nucleotide polymorphisms (SNPs). SNP-based pedigree analyses indicate a reproductive monopoly held by a single queen, with queen replacement from natal nestmates and evidence of possible multiple mating. Relatedness between pupal offspring was high (r = 0.71). It is likely that high reproductive skew among females is a founding trait of Polistes societies, conserved among species that have spread into new environments from Indomalayan origins.

A laminated paper-based analytical device (LPAD) for histidine detection was fabricated from a chromatography filtration paper and laminate films. Histidine recognition was effected by histidyl-tRNA synthetase (HisRS), and its detection was signaled colorimetrically based on the molybdenum blue reaction. The analytical conditions and detectable concentration range of histidine were examined. The method provided selective quantification from 1 to 100 μM histidine. LPAD fabrication is considerably simple, involving only the craft-cutting of the chromatography filtration paper and laminate film, and is cost-effective.

The study examines the potential of Mauritian hemp (Furcraea foetida L.), a lignocellulosic non-wood biomass, as a more environmental friendly substitute to virgin wood for printing paper production. The best pulping method for Mauritian hemp was first investigated. A4 sized papers were then produced using 100% Mauritian hemp fibres and mixtures of Mauritian hemp fibres with Elephant grass fibres and wastepaper. Using Standard tests, the physical (thickness, grammage, apparent density, water absorbency) and mechanical (tensile strength, burst strength, crease recovery, abrasion resistance) properties of the papers produced were evaluated and compared with those of an 80 gsm A4 commercial printing paper used as control. Lastly, internal sizing was done by adding different proportions of starch to the paper whose properties were closest to the control (judged most printable) to investigate any property enhancement. Soda cooking with 12% Wt/V NaOH solution at a temperature of 90 °C for 90 min was found best for pulping Mauritian hemp. The 100% Mauritian hemp paper had characteristics closest to the control, with apparent density 141.54 kg/m3, water absorbency time 1.436 s, burst strength 0.323 kPa m2/g, tensile strength 10.97 Nm/g, abrasion resistance 37.5 cycles before rupture and crease recovery angle 34.8°. Increasing the starch content from 10 to 40% caused the 100% Mauritian hemp paper’s characteristics to increasingly approach those of the control, thus showing printability improvement. The methodologies adopted for papermaking and testing demonstrated that Mauritian hemp is a suitable alternative to wood to produce good quality printing paper.

A discussion is currently under way in the literature on the sustainable benefits of recycling material, particularly paper, which has high global consumption and polluting capacity. Optimized planning of waste paper recycling networks stimulates sustainable processing efficiency, motivating the investigation of quantitative methods to guide decision-making. The objective of this article is to review papers that present quantitative models for planning waste paper recycling networks considering optimization of the echelons of this process, to analyze the evolution of research, find research opportunities and contribute to future research. The article presents an analysis of five categories of the selected studies: I—evolution of publications; II—echelons considered in different waste paper recycling systems; III—the sustainability pillars considered in the objectives of the formulated model; IV—formulations and techniques used; and V—uncertainty analysis. The proposal for waste paper recycling networks involves summary of the echelons considered in selected articles, to help future analysis. Research suggestions involving sustainability objectives, especially considering social issues, using different solution techniques and considering uncertainty were identified. This study, by reviewing the articles and identifying possibilities for future research, contributes to the development of research using quantitative methods for the efficient management of waste paper recycling networks or similar arrangements.

This study aimed to evaluate the effect of nanocellulose addition on the physical–mechanical properties of the paper produced from different fiber blends, besides comparing two nanocellulose addition methods. Three different fibers were used for fiber blending (eucalyptus, sisal, and pine). Handsheets were formed based on the mixing of all possible combinations at a 45/55 ratio in 2% consistency and 60 g/m2. Handsheet reinforcements were performed by two methods: The mixture method (MT) was a mixture of nanocellulose along with pulp during paper formation in 3, 5, and 10% addition; the coating method (CT) was the superficial coating of dry formed papers in 10% addition. Nanocellulose was produced by mechanical microfibrillation of sisal pulp. Handsheets were evaluated by physical and strength properties. Nanocellulose addition increased thickness, volume, grammage, apparent density, opacity, roughness, tensile strength, tensile index, stretch, bursting index, tear index, and fold endurance by 8.7, 8.8, 10.4, 2.1, 4.1, 23.2, 45.7, 31.8, 20.1, 14.2, 21.1, and 271.6% but reduced bulk, brightness, and air permeance by 1.9, 3.4, and 71.7%, respectively. The reinforcement methods presented distinct results. In physical properties, an increasing tendency toward nanocellulose (MT) increase was observed in thickness, grammage, and apparent density despite the decreasing trend in air permeance. No tendency was observed in other physical properties. In general, CT presented higher values of thickness, grammage, bulk, and brightness but lower values of apparent density and opacity, compared to MT. The mixture method showed an increasing tendency in strength properties with the increase of nanocellulose content. CT obtained fewer strength properties compared to MT.

This study demonstrates a method for patterning paper-based microfluidic devices. An octadecyltrichlorosilane (OTS) solution is used to coat a chromatography paper to make it hydrophobic. A low-temperature (~ 32.9 °C) atmospheric-pressure dielectric-barrier-discharge jet with a shadow mask is then used to pattern hydrophilic stripes on the OTS-coated hydrophobic paper. In this manner, 1-mm-wide hydrophilic stripes are patterned successfully. Liquids are demonstrated to be transported and mixed in the hydrophilic stripes. Water contact angle measurement, X-ray photoelectron spectroscopy, surface profiler, optical emission spectroscopy, and scanning electron microscopy are used to characterize effect of pattering.

In this paper hemicellulose was separated by using 1-ethyl-3-methylimidazolium acetate (EmimAc, an ionic liquid) -water mixtures from a paper grade market bleached hardwood kraft pulp to produce dissolving pulp. Pure EmimAc dissolves pulp fibers completely in 30 min at ambient temperatures. By adding water (as an antisolvent to EmimAc system) the cellulose dissolution decreases and by optimizing the conditions, hemicellulose is largely removed while cellulose remains as the solid residue (dissolving pulp). At optimal conditions: molar ratio of water to EmimAc of 2, 60 °C, an alpha-cellulose content of 92.2%, with a high yield (78 wt%) was obtained. The viscosity of the solvent mixture decreases by increasing water to EmimAc molar ratio, which improves the mobility of ions, thus, facilitating their penetration into pores and lumens of the fibers during the dissolution process. Cellulose purity increases and purified cellulose yield decreases with the increases in temperature and water content (up to 2 wt%) in the mixture. This study implies that the optimal EmimAc/water mixture is an effective system to separate hemicellulose from hemicellulose/cellulose matrix.

The sensitive quantitative analysis of trace heavy metallic elements (Cd, Mn, Cr, and Cu) in aqueous solutions was achieved successfully through the combination of filter paper enrichment with laser-induced breakdown spectroscopy. Filter paper was enriched with 0.4 mL aqueous solutions to form a homogeneous sample layer on the surface of the metallic target. Considering the limits of detection, the values deduced with calibration curves already exhibited the high performance of the proposed method at several hundred or 10 μg/L (Cd 0.165, Mn 0.035, Cr 0.012, and Cu 0.078 mg/L), lower than or comparable to those using other similar methods. The LIBS results agreed reasonably well with those from ICP-MS for real samples. All results showed that our method was suitable and accurate for rapid on-site detection of trace metals in aqueous solutions. This indicates that filter paper enrichment combined with laser-induced breakdown spectroscopy is a feasible approach to wastewater quality monitoring.