Search

Four organic solid wastes (coffee grounds, ground nut shell, paper money sewage sludge and cork powder) have been investigated as bloating inducing agents in lightweight aggregate (LWA) manufacturing when mixed in small proportions (2.5 wt.%) with three types of clays. The pellets obtained were fired in a rotary kiln at the maximum feasible temperature for 4 min. A similar impact was observed both in the working conditions and in the properties of the LWAs, showing that the differences between said residues are not as decisive as those of the clays to which they are added. The organic wastes have played a crucial role in achieving reducing conditions inside the aggregate. Thus, their addition has led to substantial improvements both from an operational point of view, lowering the working temperature, and from a technological perspective, favoring bloating and the development of a highly porous and lightweight structure. Leachate studies have shown that the LWAs meet the regulatory limits. The outcomes of this investigation show that, in line with the precepts of the Circular Economy, the recovery of organic wastes of different nature can have a place in the production of environmentally friendly LWAs

This work was developed within the scope of project i3N (LA/P/0037/2020. I.P. N. F. Santos thanks i3N for the BPD Grant BPD/UI96/5177/2020. S. O. Pereira thanks i3N for the BPD Grant BPD/UI96/5808/2017. The authors also thank Jonas Deuermeier for the XPS measurements. Publisher Copyright: © 2022 Elsevier Ltd Laser-induced graphene from paper (paper-LIG) was applied in non-enzymatic electrochemical sensing of uric acid (UA) in human urine. Paper-LIG was formed by CO2 laser modification of paper into a 3D graphene arrangement. Kinetic analysis of paper-LIG electrodes returned effective heterogeneous electron transfer standard rate constants of 1.4 × 10−3 cm s−1 and 7.8 × 10−4 cm s−1 for [Ru(NH3)6]2+/3+ and [Fe(CN)6]4−/3− redox probes, respectively. These electrodes were able to detect and quantify uric acid in PBS within the 10–300 μM range at pH between 5.6 and 7.4. At pH 7.4, a linear response (R2 = 0.999) from 10 to 250 μM was achieved, with a limit of detection of 3.97 μM and a sensitivity of 0.363 μA cm−2 μM−1. Paper-LIG electrodes denoted adequate selectivity in synthetic urine as well as in ascorbic acid (AA) and dopamine (DA)-containing electrolytes. Determination of urinary UA content in human samples returned a concentration of c.a. 1.8–1.9 mM, within the range for healthy individuals. Recoveries of samples spiked with 50 and 100 μM UA were 100.6% and 95.4%, respectively, with satisfactory reproducibility and stability. These cheap, lightweight, flexible, and eco-friendly paper-LIG biosensors for non-enzymatic quantification of UA in human urine pave the way to widespread application in the detection of other important biomarkers. publishersversion published

Pseudoestrogene bisphenol A (BPA) can be important ingredient of thermochromic inks, increasingly used materials in thermal printing paper, security printing, advertising, design and as temperature indicators in medicine and food industry. BPA mass fraction in thermochromic inks can be up to several percent. Hence, disposal of items with thermochromic prints pose a risk of environmental pollution. In this work BPA mass fraction was monitored during anaerobic degradation of papers with thermochromic prints in soil in both matrices: papers and soil. The degradation conditions simulated deeper layers of waste at a landfill site. Six types of papers with prints of thermochromic ink containing 2% of BPA were subjected to anaerobic degradation over up to 150 days.

The current data on climate change and environmental degradation are dramatic. The consequences of these changes are already having a significant impact on people's health. Physicians - as advocates of the patients, but also as citizens - have an ethical obligation to be involved in efforts to stop these changes. The European Federation of Internal Medicine (EFIM) strongly encourages the Internal Medicine societies and internists across Europe to play an active role in matters related to climate change and environmental degradation. At a national level, this includes advocating the adoption of measures that reduce greenhouse gas (GHG) emissions and environmental degradation and contributing to policy decisions related to these issues. At a hospital level and in clinical practice, supporting actions by the health sector to reduce its ecological footprint is vital. At the level of EFIM and its associated internal societies, promoting educational activities and developing a toolkit to prepare internists to better care for citizens who suffer from the consequences of climate change. In addition to advocating and implementing effective actions to reduce the ecological footprint of the health industry, recommending the introduction of these themes in scientific programs of Internal Medicine meetings and congresses and the pre- and postgraduate medical training. At a personal level, internists must be active agents in advocating sustainable practices for the environment, increasing the awareness of the community about the health risks of climate change and environmental degradation, and being role models in the adoption of environmentally friendly behaviour.

Flexible inkjet-printed antenna is presented. The proposed antenna is designed on a synthetic paper substrate with an area of 35 × 40 mm2 to provide frequency bands for many popular wireless applications. Simulation and measurement are used to study the performances, including the frequency bands, radiation patterns, peak gains and efficiency, of the antenna in two severely bending conditions with a curvature radius of 20 mm in the forward and backward directions. The antenna printed in photo papers material could not be fully flexible due to cracks introduced to the coating material on the surface of the photo paper. Hence, the resin coated material was only suitable for curved devices. The synthetic paper material used in this paper does not have a resin coating, therefore, the antenna does not lose its flexibility and can be bent in both the forward and backward directions without any cracks. Results show that bending in these two conditions has insignificant effects on the performances of the antenna. With a curvature radius of 20 mm in the forward direction, the measured peak gain and efficiency of the antenna are in the ranges from −3 to +2 dBi and 40% to 60%, respectively. The results together with the low cost make the antenna most suitable for many flexible 5G communications devices.

Statement of problem Quick response (QR) codes are a fast and efficient technology for linking and accessing identifying information, and their use has been proposed in forensics. The heat resistance and esthetics of denture marking methods (DMMs) have been recommended by the American Dental Association (ADA), but studies on these aspects of printed QR codes are lacking. Purpose The purpose of this study was to determine the optimal printed material with QR codes for implementation as a DMM adjusted to the recommendations of the ADA. Material and methods The behavior of 4 types of paper, bond paper, fiberglass filter paper, ultralong hydroxyapatite nanowire paper, and polyolefin and silica paper with printed QR codes was analyzed. They were exposed to temperatures between 100 °C and 1000 °C in a heat muffle for 1 hour. Each specimen was subjected to both a morphological and a thermogravimetric analysis (TGA) and scanned by using 3 different smartphones. Results The scans were positive for bond paper (33.3%), fiberglass fiber paper (50%), ultralong hydroxyapatite nanowire paper (100%), and polyolefin and silica paper (70.4%). The TGA revealed continuous decomposition curves (average 16.5 minutes at 624 °C). Conclusions Printed QR codes on ultralong hydroxyapatite nanowire paper appear to be suitable as information reservoirs, even surviving incineration, and may be implemented as a DMM conforming to the ADA recommendations.

Chronic pancreatitis is associated with impaired quality of life, high incidence of comorbidities, serious complications and mortality. Healthcare costs are exorbitant. Some medical societies have developed guidelines for treatment based on scientific evidence, but the gathered level of evidence for any individual topic is usually low and, therefore, recommendations tend to be vague or weak. In the present position papers on chronic pancreatitis from the Societat Catalana de Digestologia and the Societat Catalana de Pàncrees we aimed at providing defined position statements for the clinician based on updated review of published literature and on multidisciplinary expert agreement. The final goal is to propose the use of common terminology and rational diagnostic/therapeutic circuits based on current knowledge. To this end 51 sections related to chronic pancreatitis were reviewed by 21 specialists from 6 different fields to generate 88 statements altogether. Statements were designed to harmonize concepts or delineate recommendations. Part 2 of these paper series discuss topics on treatment and follow-up. The therapeutic approach should include assessment of etiological factors, clinical manifestations and complications. The complexity of these patients advocates for detailed evaluation in multidisciplinary committees where conservative, endoscopic, interventional radiology or surgical options are weighed. Specialized multidisciplinary units of Pancreatology should be constituted. Indications for surgery are refractory pain, local complications, and suspicion of malignancy. Enzyme replacement therapy is indicated if evidence of exocrine insufficiency or after pancreatic surgery. Response should be evaluated by nutritional parameters and assessment of symptoms. A follow-up program should be planned for every patient with chronic pancreatitis. © 2021 Elsevier España, S.L.U.

Objective The purpose of this study was to develop a natural language processing (NLP) pipeline to identify incidental thyroid nodules (ITNs) meeting criteria for sonographic follow-up and to assess both adherence rates to white paper recommendations and downstream outcomes related to these incidental findings. Methods 21583 non-contrast chest CT reports from 2017 and 2018 were retrospectively evaluated to identify reports which included either an explicit recommendation for thyroid ultrasound, a description of a nodule ≥ 1.5 cm, or description of a nodule with suspicious features. Reports from 2018 were used to train an NLP algorithm called fastText for automated identification of such reports. Algorithm performance was then evaluated on the 2017 reports. Next, any patient from 2017 with a report meeting criteria for ultrasound follow-up was further evaluated with manual chart review to determine follow-up adherence rates and nodule-related outcomes. Results NLP identified reports with ITNs meeting criteria for sonographic follow-up with an accuracy of 96.5% (95% CI 96.2-96.7) and sensitivity of 92.1% (95% CI 89.8-94.3). In 10006 chest CTs from 2017, ITN follow-up ultrasound was indicated according to white paper criteria in 81 patients (0.8%), explicitly recommended in 46.9% (38/81) of patients, and obtained in less than half of patients in which it was appropriately recommended (17/35, 48.6%). Discussion NLP accurately identified chest CT reports meeting criteria for ITN ultrasound follow-up. Radiologist adherence to white paper guidelines and subsequent referrer adherence to radiologist recommendations showed room for improvement.

Introduction The assessment of the risk of virus transmission through papers, such as postcards, is important. However, the stability of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) and influenza A virus (IAV) on different types of papers is currently unknown. Investigation of the survival time of these viruses on different types of papers will provide insights into their risk of long-distance transport by postal items. Methods We evaluated the stability of SARS-CoV-2 and IAV, mixed with a culture medium, on the surface of postcards with various coatings, including plain paper (PP), inkjet paper (IP), and inkjet photo paper (IPP). The surface structure of each paper was microscopically assessed. Results The surface structures of PP, IP, and IPP varied greatly depending on the presence or absence, and type, of coat layer, regardless of the base material. IP and IPP surfaces were less conducive to virus survival than PP surfaces, because of the difference in surface shapes. The survival times of SARS-CoV-2 on each paper were approximately 59.8 (PP), 6.5 (IP), and 9.8 h (IPP), and significantly longer than those of IAV (10.3, 1.8, and 3.3 h, respectively). Conclusions The risk of SARS-CoV-2 transmission via paper, such as postcards, is significantly higher than that of IAV transmission. While PP, IP, and IPP have the same base material, their surface structures differ, which affects viral stability. The IP and IPP surfaces are less suitable for virus survival. This study provides novel insights into the risks of viral transmission via paper.

Bio-based additives received significant attention in pulp and paper properties improvement. For this, the most cited biochemical Cellulose Nano Fibrils (CNFs) and Cationic Starch (CS) were experimentally compared with the most declared synthetic chemical, Cationic Polyacrylamide (CPAM). SEM images showed better paper surface filling by the utilization of the chemicals. The three studied polymers, in solely or combination mechanism, improved mainly bagasse pulp and paper properties compared to the blank sample, except for pulp drainage, which decreased by CNFs to lower volumes presumably due to its intrinsic characteristics. Cationic polymers (CP) compared to CP/CNFs approaches increased pulp retention and drainage but decreased paper density and strengths. The best pulp retention and drainage achieved by CS followed by CPAM, while paper air persistency, density, and strength properties evaluated highest by CP/CNFs followed by CNFs. Generally, CS revealed a more significant improvement in pulp and paper properties than CPAM either with or without CNFs.

Molybdenum sulfide (MoS2) with well-designed porous structure has the potential to be great electrode materials in sodium-ion batteries due to its high theoretical capacity and abundant resource, however, hindered by its intrinsic low conductivity and stability. Herein, MoS2 with 3D macroporous foam structure and high conductivity was obtained through SiO2 templates and integrated with carbon paper (3D F-MoS2/CP). It has showed superior specific capacity (225 mA h g−1, 0.4–3 V) and cycling stability (1000 cycles) at high rate (2000 mA g−1), with a low decay rate (0.033% per cycle) in sodium-ion batteries. The excellent electrochemical performance may originate from its unique integrated structure: 3D MoS2 macropores providing high surface area and abundant transfer channels while carbon paper enhancing the conductivity of MoS2 and avoiding unnecessary side reactions brought by binder addition.

This updated report on image guided radiation therapy (IGRT) is part of a series of consensus-based white papers previously published by the American Society for Radiation Oncology addressing patient safety. Since the first white papers were published, IGRT technology and procedures have progressed significantly such that these procedures are now more commonly used. The use of IGRT has now extended beyond high-precision treatments, such as stereotactic radiosurgery and stereotactic body radiation therapy, and into routine clinical practice for many treatment techniques and anatomic sites. Therefore, quality and patient safety considerations for these techniques remain an important area of focus.The American Society for Radiation Oncology convened an interdisciplinary task force to assess the original IGRT white paper and update content where appropriate. Recommendations were created using a consensus-building methodology, and task force members indicated their level of agreement based on a 5-point Likert scale from "strongly agree" to "strongly disagree." A prespecified threshold of ≥75% of raters who selected "strongly agree" or "agree" indicated consensus.This IGRT white paper builds on the previous version and uses other guidance documents to primarily focus on processes related to quality and safety. IGRT requires an interdisciplinary team-based approach, staffed by appropriately trained specialists, as well as significant personnel resources, specialized technology, and implementation time. A thorough feasibility analysis of resources is required to achieve the clinical and technical goals and should be discussed with all personnel before undertaking new imaging techniques. A comprehensive quality-assurance program must be developed, using established guidance, to ensure IGRT is performed in a safe and effective manner. As IGRT technologies continue to improve or emerge, existing practice guidelines should be reviewed or updated regularly according to the latest American Association of Physicists in Medicine Task Group reports or guidelines. Patient safety in the application of IGRT is everyone's responsibility, and professional organizations, regulators, vendors, and end-users must demonstrate a clear commitment to working together to ensure the highest levels of safety.

This article is part of a series on methods for living guidelines, consolidating practical experiences from developing living guidelines. It focuses on methods for identification, selection, and prioritisation of clinical questions for a living approach to guideline development.Members of the Australian Living Evidence Consortium (ALEC), the National Institute of Health and Care Excellence (NICE) and the US Grading of Recommendations, Assessment, Development and Evaluations (GRADE) Network, convened a working group. All members have expertise and practical experience in the development of living guidelines. We collated methods documents on prioritisation from each organisation's living guidelines, conducted interviews and held working group discussions. We consolidated these to form best-practice principles, which were then edited and agreed on by the working group members.We developed best-practice principles for 1) identification, 2) selection, and 3) prioritisation, of questions for a living approach to guideline development. Several different strategies for undertaking prioritising questions are explored.The paper provides guidance for prioritising questions in living guidelines. Subsequent papers in this series explore consumer involvement, search decisions, and methods decisions, that are appropriate for questions with different priority levels.

Background The screening of biological hazards, chemical contaminants and allergens in food products is a major concern of food industry since they can cause serious illnesses and even lead to death. Therefore, there is a significant interest in developing low-cost, robust, and rapid detection methods for food safety and quality analysis. Conventional methods provide accurate analytical characteristics, but require well-equipped laboratories, trained personnel, costly reagents, and complicated sample preparation procedures prior to the detection in order to obtain reliable results. Hence, they are not always ideal for on-site food surveillance. Scope and approach This paper discusses the fundamentals of microfluidic paper-based analytical devices (μPADs) and reviews the recent progress in their usage for screening biological hazards, harmful chemical residues, and allergens in food products to systematically evaluate the strengths and weaknesses of this technology. It then covers future trends and useful strategies that could be employed in μPADs design and fabrication procedures to address the critical challenges in equipment-free food analysis. Key findings and conclusions μPADs offer promising avenues to revolutionize food safety and quality analysis with merits of equipment-free sample preparation and detection at low-cost. Despite the advancement in the microfluidic technology, the manufacturing of user-friendly sample-to-answer μPADs still requires intensive research studies to be employed for robust and sensitive food safety and quality analysis.

This manuscript aimed to enhance the mechanical, thermal, and ignition properties of bagasse paper when coated with different coatings synthesized from hydroxyethyl cellulose, 1,3-di-p-toluidine-2,2,2,4,4,4-hexachlorocyclodiphosph(V)azane, Talc powder, NaHCO3, cellulose nanocrystal. The effect of these coatings on the mechanical properties was studied by measuring elongation, tensile strength, and burst strength. The stages of degradation and ash residue of the measuring specimens were determined using thermal gravimetric analysis (TGA), behind that, the ignition properties as the flame chamber (UL/94), and limiting oxygen index (LOI) was measured according to standards. These tests proved that 1,3-di-p-toluidine-2,2,2,4,4,4-hexachlorocyclodiphosph(V)azane has a direct effect on improving the mechanical characteristics and enhancing the ignition properties of the coated specimens compared to uncoated. In this study the physical, mechanical, thermal, and ignition properties of the bagasse paper sheets were enhanced by easy and low-cost method via synthesis of new coatings based on commercially available chemicals in a reasonable cost.

Laser-induced graphene (LIG) technology featuring low-cost, high-efficiency and scalability has presented great advantages in micro-supercapacitors (MSCs) fabrication. However, the limited capacitance of LIG based MSCs is still hindering their further development. Herein, we introduce joule heating as a critical in-situ treatment merged with the assembly of laser-induced graphene paper based MSCs (LIGP-MSCs) toward capacitive enhancement. By increasing heating-treatment temperature from ∼20 to 500 °C, the number of nanopores in LIGP continuously increases, attributed to the gradual decomposition of amorphous carbon components. The resulting joule-heated LIGP (J-LIGP) with improved specific surface area (160.97–533.49 m2/g) and pore volume (0.179–0.553 cm3/g) as well as superhydrophilic surface is highly suitable to be employed as J-LIGP-MSCs microelectrodes. By investigating process dependent performance, the J-LIGP-MSCs heated at 500 °C for 60 min delivers a significantly improved specific areal capacitance (CA) of 13.71 mF/cm2 at 10 mV/s, which is approximately six-fold higher than that of unheated LIGP-MSCs. By further exploring and optimizing the process efficiency, J-LIGP-MSCs with a CA of 12.61 mF/cm2 has been achieved by 550 °C heating for only 5 min. Along with superior mechanical flexibility, cyclability and structural modularity, the proposed in-situ joule heating treatment is finally proved to be a universal approach for consistently enhancing the CA of LIG based MSCs processed under various chemical modifications.

Antimicrobial stewardship programs (ASPs) have made immense strides in optimizing antibiotic, antifungal, and antiviral use in clinical settings. However, although ASPs are required institutionally by regulatory agencies in the United States and Canada, they are not mandated for transplant centers or programs specifically. Despite the fact that solid organ transplant recipients in particular are at increased risk of infections from multidrug-resistant organisms, due to host and donor factors and immunosuppressive therapy, there currently are little rigorous data regarding stewardship practices in solid organ transplant populations, and thus, no transplant-specific requirements currently exist. Further complicating matters, transplant patients have a wide range of variability regarding their susceptibility to infection, as factors such as surgery of transplant, intensity of immunosuppression, and presence of drains or catheters in situ may modify the risk of infection. As such, it is not feasible to have a “one-size-fits-all” style of stewardship for this patient population. The objective of this white paper is to identify opportunities, risk factors, and ASP strategies that should be assessed with solid organ transplant recipients to optimize antimicrobial use, while producing an overall improvement in patient outcomes. We hope it may serve as a springboard for development of future guidance and identification of research opportunities.

Mitigation of global warming, energy security and industrial competitiveness urge the energy-intensive pulp and paper industry (PPI) to transform energy use practices. This study investigates how the PPI has responded to the need for the energy transition in the 2000s. Finland and Sweden as forerunners of energy-efficient operation and decarbonization of the PPI are used as target countries. Understanding of changes in energy consumption is complemented using decomposition analysis (Logarithmic Mean Divisia Index Method) and the energy efficiency index approach. Analysis of companies’ investments in energy technologies is used for explaining changes in energy production. Evidence of significant development towards the more sustainable operation of the PPI was found. Energy consumption per produced unit has decreased, i.e., energy efficiency has improved. Fossil fuels have been partially replaced with bio-based alternatives. Thus, the CO2 intensity has decreased substantially. The generation of renewable electricity has increased in both countries. Examples of Finland and Sweden indicate that the PPI has great potential to contribute to CO2 emission reduction worldwide in the future as energy efficiency can be further improved, and the share of fossil fuels can be decreased increasing the use of biofuels and self-generated green electricity at least in kraft pulp mills.

The construction industry had approached a critical limit which led to the increase of cement production. The production of cement would cause a broader environmental implication. Cement production is a major source of carbon dioxide emission. Carbon dioxide gas contributes about 63.33% of global warming since the production of one ton of cement would emit about one ton of carbon dioxide to the environment. To mitigate this issue, the research community has investigated the use of waste materials that possess similar chemical properties with cement content as a material for partial cement replacement. The use of rice husk ash has shown to be a contending candidate in the literature. Therefore, this paper attempts at reviewing the performance of rice husk ash as partial cement replacement. It could be observed from the literature that concrete with 5% up to 15% of rice husk ash showed an equivalent performance to ordinary concrete in compressive, flexural, and tensile strength. Thus, rice husk ash can be used as a material replacement in concrete and reduces pollution that originates from cement production and open burning of rice husk.

A novel paper-based analytical device (PAD) was prepared and applied to determine the xanthine oxidase (XOD) inhibitory activity of Salvia miltiorrhiza extracts. First, polycaprolactone was 3D printed on filter paper and heated to form hydrophobic barriers. Then the modified paper was cut according to the specific design. Necessary reagents including XOD for the colorimetric assay were immobilized on two separate pieces of paper. By simply adding phosphate buffer, the reaction was performed on the double-layer PADs. Quantitative results were obtained by analyzing the color intensity with the specialized device system (including a smartphone, a detection box and sandwich plates). The 3D-printed detection box was small, with a size of 9.0 cm × 7.0 cm × 11.5 cm. Color component G performs well in terms of linearity and detection limits and thus was identified as the index. The reaction conditions were optimized using a definitive screening design. Moreover, a 10 % glycerol solution was found to be a suitable stabilizer. When the stabilizer was added, the activity of XOD could be maintained for at least 15 days under 4 °C or -20 °C storage conditions. The inhibitory activity of Salvia miltiorrhiza extracts was investigated and compared to that of allopurinol. The results obtained with the PADs showed agreement with those obtained with the microplate method. In conclusion, the proposed PAD method is simple, accurate and has potential for point-of-care testing. It also holds promise for use in rapid quality testing of medicinal herbs, intermediate products, and preparations of traditional Chinese medicines.

Made available in DSpace on 2022-04-29T08:31:12Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-10-01 Organization and planning of reverse logistics networks make sustainable processes more efficient. Thus, an important sector for connecting the collection and waste paper recycling echelons is the intermediate center. In this study, a Mixed Integer Linear Programming model, which is multi-objective, multi-product, multi-level and multi-period, was developed to optimize the waste paper logistics processes of intermediate centers. The formulation includes the following echelons: collection, considering vehicle routing with different capacities; inventory of non-baling materials; baling sorted waste and inventory of bales; selling bales; disposal of non-recyclable waste. The aims of the model include: maximizing the collected waste; minimizing distances; maximizing both the production and sale of bales, and minimizing costs. According to research carried out in the literature, the developed model is a new proposal and to implement it, the Weighted Goal Programming and Revised Multi-Choice Goal Programming approaches were used to deal with multiple objectives and incorporate uncertainty into the quantity of waste available for collection. To analyze the proposed model, computational tests were executed with instances based on real data from a Brazilian company in the sector. For all performed tests, General Algebraic Modeling System 23.6.5 modeling language and CPLEX 12.2.0.2 solver were used for modeling and optimization. The results show that this study presents formulation and technological approaches that represent real situations and provide competitive solutions to the problem. Sáo Paulo State University “Júlio de Mesquita Filho” [Universidade Estadual Paulista Júlio de Mesquita Filho] School of Engineering of Guaratinguetá [Faculdade de Engenharia de Guaratinguetá] Production Department, Av. Ariberto Pereira da Cunha, 333, Portal das Colinas Agulhas Negras Military Academy [Academia Militar das Agulhas Negras] Rodovia Presidente Dutra, km 306, s/n Escola Preparatória de Cadetes do Exército Avenida Papa Pio XII 350 Jardim Chapadão Campinas - SP Brazil, Avenida Papa Pio XII, 350, Jardim Chapadão, Campinas - SP Sáo Paulo State University “Júlio de Mesquita Filho” [Universidade Estadual Paulista Júlio de Mesquita Filho] School of Engineering of Guaratinguetá [Faculdade de Engenharia de Guaratinguetá] Production Department, Av. Ariberto Pereira da Cunha, 333, Portal das Colinas

Tremendous attention has been paid on high efficiency, readily available and stability of electrocatalysts. Herein, we ingenious report a one-step reaction strategy synthesis of CoFe/CP grown on three-dimensional (3D) nanoarray carbon paper (CP) containing non-precious metals for oxygen evolution reaction (OER) with low-cost and unique hierarchical porous structure. This amorphous CoFe/CP hybrid exhibits commendable electrocatalytic performance in the OER process, requiring only overpotential of 278 mV to achieve 10 mAcm−2 in 1.0 M KOH solution and a lower Tafel slope of 49.12 mVdec-1. In addition, this sample shows a long-term durability even at 200 mAcm−2 without obvious decay, which attributes to peculiar multistage graded nano structure and the change of composition at the interface of CP. Therefore, the remarkable OER activity can provide a new strategy to construct potential candidates, which will replace the state-of-the-art precious metals for OER in the future.

Palliative radiation therapy (pRT) is an effective tool for people with incurable cancer, in the treatment of many cancer-related symptoms such as pain, bleeding and dyspnea. As utilization rates for palliative radiation therapy increase, the demands on the healthcare system continue to grow. Radiation Therapists with advanced knowledge, skills and judgements began demonstrating their ability to practice autonomously in 2004, with the development of the Clinical Specialist Radiation Therapist (CSRT) role. Since this time, CSRTs with a specific focus in pRT (pCSRT) have been increasing in both numbers as well as their positive effects on the cancer care system. Integrating a pCSRT into the existing pRT system has resulted in increased access to and quality of pRT being delivered to palliative cancer patients. The benefits of the addition of pCSRTs to the cancer care system include increasing system capacity and increasing quality of care. This white paper provides information related to the improvements that can be realized in a RT program related to the care and treatment of its palliative patients by adding a pCSRT to the interprofessional healthcare team and suggest it as one of many strategies that can be undertaken to make improvements to access and quality of care.

In recent years, many projects have been developed to reduce the energy consumption of buildings, both from the point of view of energy efficiency and the integration of renewable energies. However, few projects are related to the problem of integrating DER in environments dominated by high-tech equipment, the so-called ”critical loads”: data centers, railroad stations, airports, and hospitals. The European Interreg Sudoe IMPROVEMENT project aim is to renovate existing public buildings where critical loads predominate, converting them into nearly zero-energy buildings (NZEB), and for this purpose, it integrates combined cooling, heat, and power (CCHP) microgrid with renewable and other distributed energy resources (DER) like hybrid energy storage systems (ESS). With still one year to go before the end of the project, the consortium partners present in this position paper the latest progress of their respective work packages to date. info:eu-repo/semantics/publishedVersion

The use of administrative databases and clinical registries in lower extremity arthroplasty research is growing. Such observational studies are unable to fully control for confounders and cannot establish causality. However, many authors use causal language when describing their aims or findings, potentially misleading readers. We examined the prevalence of causal language and inferences in the lower extremity arthroplasty literature.We systematically identified administrative database and registry studies on hip and knee arthroplasty that were published in 4 orthopaedic journals in 2020. Papers were graded independently by two reviewers for the presence of causal language in both the title and abstract as well as the full text. Chi-squared analyses were conducted to determine the relationship between the causality grading and article characteristics including the journal of publication.Of 116 eligible articles, we classified 79.3% of titles and abstracts as either consistently causal or inconsistently causal, with only 20.7% as consistently non-causal. A total of 40.5% of full texts were consistently causal, 49.1% were inconsistent, and 10.3% were consistently non-causal. Chi-squared analyses revealed no statistically significant association between the title and abstract's grading and the journal (p = .720), nor with the use of a database or registry (p = .716).Causal language and inferences were present in 79.3% of titles and abstracts of lower extremity arthroplasty observational database studies published in 2020. The high prevalence of causal language and inferences in the arthroplasty literature may mislead readers.

Producing living guidelines requires making important decisions about methods for evidence identification, appraisal and integration to allow the living mode to function. Clarifying what these decisions are and the trade-offs between options is necessary. This paper provides Living Guideline developers with a framework to enable them to choose the most suitable model for their living guideline topic, question or context.We developed this guidance through an iterative process informed by interviews, feedback and a consensus process with an international group of Living Guideline developers.Several key decisions need to be made both before commencing and throughout the continual process of Living Guideline development and maintenance. These include deciding what approach is taken to the systematic review process; decisions about methods to be applied for the evidence appraisal process, including the use of unpublished data; and selection of "triggers" to incorporate new studies into Living Guideline recommendations. In each case, there are multiple options and trade-offs.We identify trade-offs and important decisions to be considered throughout the Living Guideline development process. The most appropriate, and most sustainable, mode of development and updating will be dependent on the choices made in each of these areas.

Neonatal and infantile cholestasis (NIC) can represent the onset of a surgically correctable disease and of a genetic or metabolic disorder worthy of medical treatment. Timely recognition of NIC and identification of the underlying etiology are paramount to improve outcomes. Upon invitation by the Italian National Institute of Health (ISS), an expert working grouped was formed to formulate evidence-based positions on current knowledge about the diagnosis of NIC. A systematic literature search was conducted to collect evidence about epidemiology, etiology, clinical aspects and accuracy of available diagnostic tests in NIC. Evidence was scored using the GRADE system. All recommendations were approved by a panel of experts upon agreement of at least 75% of the members. The final document was approved by all the panel components. This position document summarizes the collected statements and defines the best-evidence diagnostic approach to cholestasis in the first year of life.

In those cases where construction-generated soils with high water contents are used as filling or embankment materials, it is sometimes difficult to satisfy the specified compaction degrees. Recently, soil stabilization using a paper sludge ash-based stabilizer (PSAS) has been developed. Paper sludge (PS) ash is waste generated by the incineration of PS discharged from paper mills. It has been found that PS ash can absorb and retain excess water; and therefore, PS ash can simultaneously improve the stability of muds when it is mixed with them. However, the current mixture design approach for PSAS-treated soils is only applicable to muds with water contents exceeding the liquid limits and cannot be applied to construction-generated soils in which the coarse fraction is dominant. Therefore, this study evaluated the effects of a PSAS on the compaction and mechanical characteristics of coarse-grained soils to use them as materials for irrigation earth dams. A series of compaction tests were conducted on two types of soil samples treated with a PSAS to investigate its effects on the compaction characteristics. The compaction characteristics obtained from the tests were assessed considering the water absorption and retention performance of the PSAS. It was found that the modified optimum water content w*opt of the treated samples, which was evaluated using the amount of water unabsorbed and unretained by the PSAS, was almost equal to the wopt of the untreated samples. Consequently, a new mixture design approach was proposed based on the compaction characteristics. The calculated results successfully demonstrated that, if the compaction curve of an untreated sample and the water absorption and retention ratio, Wab, of the PSAS corresponding to a certain curing period are obtained, the range in the PSAS addition amount, APS1m3, required to attain the targeted compaction degree, (Dc)target, for the curing period can be estimated without conducting compaction tests on the treated samples. Finally, the strength characteristics of the treated samples prescribed by the proposed mixture design method were investigated by conducting CBR tests and CU ¯ TC tests. Based on the test results, discussions were made on the contribution of the proposed mixture design to the strength development of the treated samples and on the development mechanism.

As a crucial biomarker for some diseases, the determination of cholesterol in human serum is of great significance for the diagnosis and prevention of these diseases. Hence, a portable cholesterol detection method is necessary for clinical and domestic applications. Here, a portable paper sensor was designed for cholesterol detection by modifying screen-printed electrode (SPE) with nanoporous gold (NPG). To achieve the reliable cholesterol detection, a synergistic strategy was proposed based on the oxidation of cholesterol by cholesterol oxidase (ChOx) and the reduction of oxidation product (H2O2) by NPG. Compared to existing electrochemical sensors, the resulting paper sensor exhibited a wider linear response in a range from 50 μM to 6 mM as well as a higher sensitivity of 32.68 μA mM−1 cm−2 with a lower detection limit of 8.36 μM. Moreover, the portable paper sensor presented strong anti-interference capability and stability in the detection of cholesterol in human serum, and the data detected by the portable paper sensor were consistent with that obtained by an automatic biochemical analyzer. These unique performances confirmed that the proposed paper sensor was a sensitive, reliable, and portable cholesterol detection method, making it a good choice for cholesterol detection.

Graphene-based nanomaterials possess broad applications because of their excellent multi-functional properties. In this work, a facile self-assembling method was presented for preparing one kind of graphene oxide-based paper/hollow microspheres hybrid. It was found that most of the hollow microspheres can strongly anchored on the surface of graphene oxide paper (GOP) by an in-situ scanning electron microscope peeling testing combining with molecular dynamics (MD) simulation. In addition, the uniform distribution of hollow microspheres on the surface of GOP cannot only provide a better surface wettability, but also can effectively improve the interfacial stress-transfer capability between such hybrid and polymer matrix. Our work provides a guidance for the structural designs of graphene-based nanomaterials and broaden their applications.

Inherent hydrophilicity and poor water resistance prevent using lignocellulosic materials as green plastic al- ternatives to fossil fuel-based plastics. Here, we report a facile metal-ion-modification (MIM) route, swelling with aqueous metal ion solutions, and drying to convert conventional hydrophilic paper and wood pulp into biode- gradable hydrophobic paper and tableware without the addition of hydrophobic sizing chemicals/materials. Metal ions such as Fe3+ and Zr4+ can coordinate with pulp fibers' polar groups (i.e., OH, C-O, and COOH) that induce self-assembly of their surface fibrillated "hairy" cellulose nanofibrils to form a more compact structure with fewer available OH groups for water sorption. This decreases the surface energy of pulp fibers and increases their hydrophobicity and water resistance. Only similar to 3 mg of metal ions is needed to induce the wettability tran- sition in 1 g of kraft pulp, resulting in hydrophobic paper and tableware with water contact angles (WCAs) of 120-140 degrees. The coordinated Fe3+ and Zr4+ are stable, with negligible metal leaching during use, allowing the hydrophobic paper and tableware to be used for food packaging. This MIM technique can be integrated into the existing paper-making process for the scalable production of hydrophobic papers and tableware, providing an alternative route for developing sustainable and biodegradable plastic counterparts. Published version Public domain – authored by a U.S. government employee

With the increased awareness of reusing solid wastes for higher sustainability and the concern of water pollution associated with phosphorus over-emission, there are strong interests in developing solid waste based adsorbents for purifying phosphorus-containing wastewater. As a rich calcium resource, paper mill sludge (i.e., a major solid waste from pulping industry) can be used as phosphorus removal adsorbent after calcination. Thus, in this work, a simple and clean thermally treating route has been proposed for preparing calcium-containing biochar from paper mill sludge. The effect of the physicochemical properties of paper mill sludge and its carbonization condition on phosphorus adsorption has been analyzed. Moreover, the influence of some key adsorption parameters, e.g., biochar dosage, initial pH of solution, co-existing anions, initial phosphorus concentration and contact time has also been investigated. The results showed that the phosphorus adsorption data could be fitted well with pseudo-second-order kinetic and Langmuir isothermal models. The calculated maximum adsorption capacity of the as-prepared optimal calcium-containing biochar could reach to 68.49 mg·g−1 at 25 °C. Combined with the characterization results, it can be reasonably inferred that the adsorption process was chemisorption-dominated. Lastly, the application of this spent adsorbent in agriculture field has also been discussed. In brief, this work provided a feasible strategy for converting paper mill solid waste to an environmental functional material (i.e., calcium-rich biochar) for remediation of eutrophic water.

This study optimizes a novel surfactant-assisted green liquor dregs (GLD) pretreatment of paper mill sludge (PMS), both of which are wastes from the kraft pulping industry, using a combined Response Surface Methodology (RSM) design. Optimized conditions give a maximal reducing sugar release of 16.38 g/L. A substantial reduction in heavy metals aluminum, chromium, cobalt, arsenic, lead, and copper after pretreatment illustrates the enhancement of substrate digestibility by reducing toxic elements. Separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) for hydrogen production are assessed. SSF produced a hydrogen yield of 3.72 mL/g, displaying a 36.26% increase from pretreated PMS compared to SHF. These findings provide insights into possible methods of reducing process duration, energy input, and costs incurred with waste disposal within the paper industry. Furthermore, improved hydrogen yield using an SSF process demonstrates the potential beneficiation of pulp and paper GLD and PMS wastes.

The fiber of paper mulberry, which is mostly grown in the East Asian region, varies in both length and width—even if from the same species—depending on the country, soil, and climate where it is grown. This accounts for differences in the quality of handmade paper between domestic and imported products. Once handmade paper is manufactured as sheets, its origin cannot be determined from a morphological perspective, regardless of macroscopic and microscopic observations. Therefore, this study attempted to determine the origin of Korean and imported products using mulberry bast fiber and handmade paper from a chemometrics perspective. The inorganic components of wood are absorbed from the soil and exist in the bark of trees; thus, metal and rare-earth elements in the bast fibers and handmade papers were quantitatively analyzed using inductively coupled plasma-atomic emission spectroscopy/mass spectrometry (ICP-AES/MS). Following this, a prediction model of their origin was constructed by applying multivariate statistical analysis, i.e., a partial least squares-discriminant analysis (PLS-DA) loading plot was constructed, which helped in identifying the discrimination factors resulting from their origin. According to the ICP-AES results, Pb was only detected in the Gyeongbuk Mungyeong dak sample of the Korean bast fibers. The Chinese bast fiber sample had high contents of Ca, and B and Zn were detected only in the Chinese bast fiber samples. Bast fiber samples from China, Japan, and Thailand showed relatively high contents of Al, Ca, and Na. Meanwhile, Cu and Zn were detected in the handmade paper manufactured from the imported materials. According to the ICP-MS results, among the Korean handmade papers, the products from Gyeongbuk Mungyeong, Andong, and Chungbuk Goesan exhibited a high U content and that from Gapyeong had high Sc, Rb, Sr, and Ba contents. Thus, the elemental analysis employed in this study effectively identified the origin of the papers. The origin prediction by PLS-DA for the domestic and imported products revealed an accuracy of 86.4% and 72.7% for ICP-AES and ICP-MS methods, respectively, which is deemed acceptable to assess the origin. We believe this method significantly contributes to determining the origin of paper mulberry bast fiber and handmade paper manufactured in East Asia.