Search

The emerging ultrawide-bandgap AlGaN alloy system holds promise for the development of advanced materials in the next generation of power semiconductor and UV optoelectronic devices. Within this context, heterostructures based on III-nitrides are very popular in view of their applications as electronic and optoelectronic components. AlGaN-based deep UV emitters are gaining visibility due to their disinfection capabilities. Likewise, high electron mobility transistors are attracting increasing attention owing to their superior electron transport which yields high-speed and high-power applications. These devices are conventionally made of AlGaN/GaN heterostructures grown on foreign substrates. However, structural defects, including stress induced by a mismatch in unit cell parameters and the presence of dislocations, can not only decrease the efficiency of the light emitters (by facilitating the non-radiative recombination of electron–hole pairs), but also impede electron mobility within the two-dimensional electron gas at the AlGaN/GaN interface. Therefore, the significance of obtaining high-quality AlGaN layers becomes evident. Including a thin AlN interlayer between the GaN buffer layer and AlGaN is a possible answer to address these drawbacks. Not only do we show that a thin AlN layer, approximately ≤3 nm in thickness, between the GaN buffer and AlGaN layers, is effective in decreasing the dislocation densities in the AlGaN layer by around 30%, but also this is responsible for an increase in the electron mobility (approximately 33%) compared to a classical AlGaN/GaN heterostructure. Additionally, the resulting heterostructure exhibits better optical quality, with a 7-fold increase in intensity as well as a 20% reduction in full-width at half-maximum in the AlGaN emission. [ABSTRACT FROM AUTHOR]

We present narrow-band polarization-sensitive reflectance of GaN/AlGaN heterostructures in the mid-infrared range. Experimental measurements performed at 15° angle of incidence show the excitation of a Berreman mode at the interface between GaN and sapphire substrate. A transfer matrix method for anisotropic layers has been used to analyze the obtained results. The contribution of the two-dimensional electron gas at the interfaces of the heterostructures has been included by proper modelization of an effective thin layer.

Distinguishing between different handedness of circularly polarized light can be a useful additional property in photodetector technology. The integration of this functionality can be obtained either using optical media with chiro‐optical response, or by the employment of chiral metamaterials. In this work, 3D chiral metasurfaces composed by a 3D helix array, are integrated onto a micrometer‐scale silicon‐based transistor and act as optical filter for circularly polarized light. The technological process involving focused electron beam induced deposition for helix manufacturing is carefully studied with respect to its effect on the phototransistor response. The integrated system exhibits a photoresponse which is dependent on the circular polarization, with a promising asymmetry factor in the visible spectral range. The proposed technology can pave the way for novel potential applications in diverse areas such as materials science, bioimaging, and quantum computing. [ABSTRACT FROM AUTHOR]

MoS2 is a two-dimensional layered transition metal dichalcogenide with unique electronic and optical properties. The fabrication of ultrathin MoS2 is vitally important, since interlayer interactions in its ultrathin varieties will become thickness-dependent, providing thickness-governed tunability and diverse applications of those properties. Unlike with a number of studies that have reported detailed information on direct bandgap emission from MoS2 monolayers, reliable experimental evidence for thickness-induced evolution or transformation of the indirect bandgap remains scarce. Here, the sulfurization of MoO3 thin films with nominal thicknesses of 30 nm, 5 nm and 3 nm was performed. All sulfurized samples were examined at room temperature with spectroscopic ellipsometry and photoluminescence spectroscopy to obtain information about their dielectric function and edge emission spectra. This investigation unveiled an indirect-to-indirect crossover between the transitions, associated with two different Λ and K valleys of the MoS2 conduction band, by thinning its thickness down to a few layers. [ABSTRACT FROM AUTHOR]

In this research work, we present a study on time-sequenced plasma-enhanced atomic layer deposition (PE-ALD) processes towards the achievement of high-quality α-MoO3 thin films which are suitable for exfoliation. In particular, a conventional precursor injection method along with a boosted precursor delivery approach are discussed and analysed. In the latter, the proposed gas supply mechanism ensures a large number of deposited Mo atoms per unit of time, which, along with a proper thermal energy, leads to high-quality and oriented orthorhombic α-MoO3 films. The proposed boosted approach is also compared with post growth annealing steps, resulting in more effective achievement of a highly oriented orthorhombic α-MoO3 phase and less time consumption. [ABSTRACT FROM AUTHOR]

In this research work, we present a study on time-sequenced plasma-enhanced atomic layer deposition (PE-ALD) processes towards the achievement of high-quality α-MoO3 thin films which are suitable for exfoliation. In particular, a conventional precursor injection method along with a boosted precursor delivery approach are discussed and analysed. In the latter, the proposed gas supply mechanism ensures a large number of deposited Mo atoms per unit of time, which, along with a proper thermal energy, leads to high-quality and oriented orthorhombic α-MoO3 films. The proposed boosted approach is also compared with post growth annealing steps, resulting in more effective achievement of a highly oriented orthorhombic α-MoO3 phase and less time consumption. [ABSTRACT FROM AUTHOR]

Graphitic carbon nitride (g-C3N4), possessing high thermal and chemical stability, non-toxicity, facile synthesis, and low band gap energy is a promising candidate for photocatalytic applications. In this study, bulk and exfoliated g-C3N4 were synthesised from different precursors (melamine and urea). Moreover, the surface of bulk g-C3N4 and exfoliated g-C3N4 was modified with graphene (0.5 wt% and 1 wt%) aiming to obtain a prolonged carrier lifetime. The effect of g-C3N4 synthesis from various precursors and the influence of graphene content on the photocatalytic activity during the degradation of a water–methanol mixture under UVC irradiation were examined, in comparison to commercial P25. Hydrogen, methane and carbon monoxide were the decomposition products; hydrogen was the main product of decomposition, whereas CH4 and CO resulting from the reduction of CO2 were generated in a significantly smaller amount. All the produced photocatalysts, whether pure or modified with graphene, exhibited higher activity than the commercial photocatalyst P25. [ABSTRACT FROM AUTHOR]

In this contribution, we present an experimental and numerical study on the coating of Al plasmonic nanostructures through a conformal layer of high-refractive-index molybdenum oxide. The investigated structures are closely coupled nanodisks where we observe that the effect of the thin coating is to help gap narrowing down to the sub-5-nm range, where a large electromagnetic field enhancement and confinement can be achieved. The solution represents an alternative to more complex and challenging lithographic approaches, and results are also advantageous for enhancing the long-term stability of aluminum nanostructures. [ABSTRACT FROM AUTHOR]

Electrochemical sensors for monitoring biochemical substances are attracting considerable attention. These devices are usually based on enzymes that are sensitive and very specific. Still, the activity of those enzymes is lost with changes in temperature or pH. Non-enzymatic electrochemical sensors – fabricated via the modification of the electrode surface with metal oxide nanoparticles – are an ideal answer to address that problem. In this study, we investigated the photo-electrochemical properties of CuO–TiO2 heterojunctions for glucose sensing in alkaline media. A combination of high-resolution (scanning) transmission electron microscopy, spatially resolved electron energy-loss spectroscopy, energy-dispersive X-ray spectroscopy and X-ray powder diffraction, was used to study in detail the microstructures of the prepared specimens. These results highlighted the strong intertwining between the TiO2 nanoparticles and the Cu-based nanoparticles, which present a metallic core with a CuO rich surface. In addition, we showed that CuO, joint to TiO2, has smaller size compared to pure CuO, which entails larger specific surface area available for the glucose electro-oxidation, which consequently enhanced the electrochemical features. The influence of Cu loading over the sensing performance of TiO2 was examined in detail carrying out electrochemical sensing tests under dark, laboratory and halogen lamp irradiation conditions. Results demonstrated that, under halogen lamp irradiation, modified CuO–TiO2 electrodes showed a specific response signal that is four times higher than that of pure CuO. Those increased photo-electrochemical properties in CuO–TiO2 heterojunctions are likely due to a synergistic effect between the microstructural characteristics and effective separation of photo-generated excitons created at the heterojunction interface. Results of this study offer applicable guidelines for designing photo-electrochemical screen-printed electrodes based on nano-sized CuO on titania for efficient detection of glucose. [ABSTRACT FROM AUTHOR]

The development of highly efficient photocatalyst under visible light still a challenge. Herein we present band gap modification of NH 2 -MIL-125 by encirclement with suitable semiconductor that possesses a narrow band gap Ag 3 PO 4 nanoparticles (NPs). The band gap of NH 2 -MIL-125 was decreased from 2.51 to 2.39 eV, making them potential candidates for photocatalytic applications. Our prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR) and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). TEM characterizations indicated that NH 2 -MIL-125 MOFs are coated with Ag 3 PO 4 NPs. The photocatalytic activity (PCA) was evaluated in the liquid-solid phase, by monitoring the degradation of an organic dye (methylene blue (MB) and rhodamine-B (RhB)) under visible-light irradiation. Furthermore, the Ag 3 PO 4 @NH 2 -MIL-125 nanocomposites shown themselves to be the most active with the reaction rate being 39 and 35 times higher than the well known Degussa P25 TiO 2 toward photocatalytic degradation of MB and RhB. [ABSTRACT FROM AUTHOR]

B-site Fe-doped (Ba0.85Ca0.15)(Ti0.9Zr0.1)O3 was synthesized by a facile chemical route to study the effect of doping on its physical properties. Detailed analysis of X-ray diffraction and Raman spectroscopy data revealed an increased lattice strain and thereby deviation from the morphotropic phase boundary with the progressive doping of Fe from 1 to 5 mol%. Such structural changes have resulted in the weakening of the energy band gap as well as deterioration of the ferroelectric polar nature which was evidenced by a shift of tetragonal to cubic transitions towards room temperature and hard doping effects in ferroelectric hysteresis. The doped samples exhibited room temperature ferromagnetism. Combined Mossbauer and X-ray photoelectron spectroscopic studies suggest that oxygen vacancies and defect complexes induced by Fe doping play a major role in magnetic properties. Local piezoresponse measurements illustrated imprint characteristics of ferroelectric domains in undoped and doped samples at the nanoscale. Room temperature magnetoelectric (ME) measurements revealed that 1 mol% Fe doped sample, having higher ferroelectric polarization and moderate magnetization, exhibits a strong ME response with a coefficient of 12.8 mV cm−1 Oe−1. The present study on Fe-doping effects on the structure and related ME properties of this important lead-free material is useful to tailor multiferroic applications in electronics. [ABSTRACT FROM AUTHOR]

Tungsten, silver, and tungsten/silver co-doped titaniananopowders were synthesised via an aqueous sol-gel method. The dried gels were thermally treated at 2 different temperatures, and the occurrence of the amorphous phase was assessed, using the combined Rietveld-RIR method, on the X-ray powder diffraction data. Systematic studies of the crystal structure and of the optical properties of the powders - made with diffuse reflectance spectroscopy (DRS) - were performed. The energy band gap was calculated using the differential reflectance method; their morphology was investigated using field emission scanning electron microscopy and transmission electron microscopy analyses (FE-SEM and TEM, respectively). The photocatalytic activity of the samples was assessed in liquid-solid phase, under UVA-light and visible-light irradiation, monitoring the degradation of an organic dye. The influence of the phase composition, optical properties, dimensions, and specific surface area of the powders on the photocatalytic activity was thoroughly discussed. [ABSTRACT FROM AUTHOR]

Abstract: A series of TiO2–SiO2 mixtures – having the following stoichiometry Ti1−x Si x O2, with x =0, 0.1, 0.3 and 0.5 atoms per formula unit – were prepared by using precursor oxides and fired at three temperatures (900, 1000 and 1200°C). The modifications in the structure and, consequently, on the photocatalytic activity, induced by the addition of SiO2 into the TiO2 powder, were thoroughly investigated by using various analytical techniques: X-ray powder diffraction, electron microscopy (FE-SEM and TEM), XPS, FT-IR, DRS and BET analysis. The results underlined as essentially no solid solution occurs between the two crystalline end-members. Nevertheless, silica addition caused a retarding effect on anatase-to-rutile phase transformation and on the crystallite growth. The photocatalytic activity of the powders was assessed in gas phase and the results were explained by taking into account the anatase and rutile relative amounts in the samples, their crystallite size, the surface hydroxyl groups adsorbed on the photocatalysts and the surface area of the mixtures. [Copyright &y& Elsevier]

The growing world energy consumption, with reliance on conventional energy sources and the associated environmental pollution, are considered the most serious threats faced by mankind. Heterogeneous photocatalysis has become one of the most frequently investigated technologies, due to its dual functionality, i.e., environmental remediation and converting solar energy into chemical energy, especially molecular hydrogen. H2 burns cleanly and has the highest gravimetric gross calorific value among all fuels. However, the use of a suitable electron donor, in what so-called "photocatalytic reforming", is required to achieve acceptable efficiency. This oxidation half-reaction can be exploited to oxidize the dissolved organic pollutants, thus, simultaneously improving the water quality. Such pollutants would replace other potentially costly electron donors, achieving the dual-functionality purpose. Since the aromatic compounds are widely spread in the environment, they are considered attractive targets to apply this technology. In this review, different aspects are highlighted, including the employing of different polymorphs of pristine titanium dioxide as photocatalysts in the photocatalytic processes, also improving the photocatalytic activity of TiO2 by loading different types of metal co-catalysts, especially platinum nanoparticles, and comparing the effect of various loading methods of such metal co-catalysts. Finally, the photocatalytic reforming of aromatic compounds employing TiO2-based semiconductors is presented. [ABSTRACT FROM AUTHOR]

This article reports a novel photocatalytic lime render for indoor and outdoor air quality improvement that is composed of a lime binder and doped TiO2 (KRONOClean 7000®) nanoparticles. These nanoparticles were distributed throughout the bulk of the finishing render, instead of as a thin coating, thus ensuring the durability of the photocatalytic properties upon superficial damage. The physical properties of these renders were not affected by the addition of nanoparticles except in the case of surface area, which increased significantly. In terms of their photocatalytic activity, these novel lime renders were shown to degrade up to 12% NOx under UV light and up to 11% formaldehyde under visible light. [ABSTRACT FROM AUTHOR]

The use of wastes, some of them hazards, as raw materials of ceramic pigments has been a way to diminish their environmental impact, to economically valorize them, and to face the depletion of virgin raw materials. In this work were prepared pigments having in their composition only industrial wastes: Cr/Ni electroplating (ES), and sludges from the cutting of natural stones—marble (MS) and granite (GS). The prepared mixtures were calcined at three temperatures (1100, 1200, and 1300 °C) and the obtained powders were characterized by XRD and UV-vis. Their coloring strength and thermal stability were assessed by adding them to different ceramic substrates: glazes (transparent bright and opaque matte) and a stoneware paste. The CIEL*a*b* coordinates of the fired materials were measured. The developed pigments are thermally stable and exhibit good tinting power, originating nicely colored and defect-free ceramic materials. [ABSTRACT FROM AUTHOR]

Lime slaker grits and biomass fly ash are solid wastes produced by the Kraft paper-pulp industry that are commonly disposed of in landfill. However, recent studies and European regulations discourage such disposal practices. This work investigates an alternative and innovative way to recycle and reuse these wastes in the production of green geopolymeric mortars intended for application in the construction industry. Here, biomass fly ash was used as the main source of alumino-silicate in the binder precursor (70 wt.% substitution to metakaolin), and grits (ranging from 1–12.5 mm, as provided by the industry) were reused as aggregate. Aggregate granulometry was also completed by using a commercial natural siliceous sand (<1 mm). Mortars using sand only were prepared for comparative reasons. The implemented mix was designed to investigate the influence of the grits on the mortar's properties such as its binder/aggregate ratio, workability, bulk density, water sorptivity, and compressive strength. At the same time, waste reuse was analysed in light of its limitations and potentialities. Moreover, in the pursuit of sustainability, the manufacturing process that was followed was highly cost-effective in ambient curing conditions (20 °C, 65% RH), which avoided the use of any external source of energy as commonly used in geopolymers processing. The achieved results proved that the combined use of these wastes, which to date has hardly been explored, along with ambient manufacturing conditions increases the material sustainability. The produced mortars are suitable for innovative applications in various fields, with a particular focus on construction and contribute to the circular economy. [ABSTRACT FROM AUTHOR]

I Nanomaterials i was able to uphold its high standards for published papers due to the outstanding efforts of our reviewers. Regardless of whether the articles they examined were ultimately published, the editors would like to express their appreciation and thank the following reviewers for the time and dedication that they have shown I Nanomaterials i : The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). Thanks to the efforts of our reviewers in 2022, the median time to first decision was 12.7 days and the median time to publication was 2.9 days. [Extracted from the article]

Graphitic carbon nitride (g-C3N4), possessing high thermal and chemical stability, non-toxicity, facile synthesis, and low band gap energy is a promising candidate for photocatalytic applications. In this study, bulk and exfoliated g-C3N4 were synthesised from different precursors (melamine and urea). Moreover, the surface of bulk g-C3N4 and exfoliated g-C3N4 was modified with graphene (0.5 wt% and 1 wt%) aiming to obtain a prolonged carrier lifetime. The effect of g-C3N4 synthesis from various precursors and the influence of graphene content on the photocatalytic activity during the degradation of a water–methanol mixture under UVC irradiation were examined, in comparison to commercial P25. Hydrogen, methane and carbon monoxide were the decomposition products; hydrogen was the main product of decomposition, whereas CH4 and CO resulting from the reduction of CO2 were generated in a significantly smaller amount. All the produced photocatalysts, whether pure or modified with graphene, exhibited higher activity than the commercial photocatalyst P25. [ABSTRACT FROM AUTHOR]

The work here deals with the observation of structural, optical and magnetic property of Eu2+ doped SnO2 nano particles. The structure is characterized by X-ray diffraction(XRD), transmission electron microscopy (TEM), Raman spectroscopy, UV–Vis absorption, photoluminescence (PL), and time resolved PL (TRPL) spectroscopy. The introduction of Eu affects the crystallite size and substitutes with Sn without showing any interstitial defect formation. With 1% doping as the limit for entering the crystal, the crystallite size shows expansion. Upon excitation at 400 nm, the presence of Eu2+ is approved with the absence of emission around 613 nm in the doped system. Decrease in the band gap with creation of sub-band gap states under doping is reported and with the increase in Eu2+ concentration, the increase in probability of transfer of nonradiative energy is observed. Further, magnetic properties are determined by investigating magnetization vs. applied fields. A ZFC–FC measurement for the system showing highest magnetization is also performed. To boot, the state of Eu2+ is also made confirmed with the observed EPR splitting at g = 1.88. Finally, a new approach through density functional theory has been carried out for quantitative and qualitative justifications. The minimum energy states have been computed by varying the internal positions of atoms under various defined parameters. The electronic states and density of states (DOS) behavior have been calculated for justified prediction of lattice sites and respective presence of atoms. The stable magnetic ground state has been estimated using the theoretical technique. [ABSTRACT FROM AUTHOR]

Abstract: Anatase-structured TiO2 films were deposited on a commercial fluorinated polymer (FEP) with a treated surface, by means of a sol–gel dip-coating technique. Two different curing temperatures were investigated and the film microstructures were characterized by X-ray diffraction, atomic force microscopy and scanning electron microscopy analyses. The prepared samples presented very high performances in terms of photocatalytic activities, analyzed by the degradation of an organic dye in a liquid medium, and of bactericidal activities, tested on Staphylococcus aureus (S. aureus, a Gram positive bacterium) and Escherichia coli (E. coli, a Gram negative bacterium). [Copyright &y& Elsevier]

Rigorous peer-reviews are the basis of high-quality academic publishing. Thanks to the great efforts of our reviewers, I Materials i was able to maintain its standards for the high quality of its published papers. Thanks to the contribution of our reviewers, in 2021, the median time to first decision was 15 days and the median time to publication was 38 days. [Extracted from the article]

Abstract: Karrooite, MgTi2O5, is a promising ceramic pigment due to its high refractoriness and refractive indices, as well as its ability to host transition metal ions in two crystallographically distinct octahedral sites. The colouring performance was investigated combining X-ray powder diffraction with UV–vis–NIR spectroscopy on karrooite doped with V, Cr, Mn, Fe, Co or Ni (M) according to the formula Mg1− x Ti2− xM 2 x O5, with x=0.02 and 0.05. Transition metals solubility in the karrooite lattice is not complete and a second phase is always present (geikielite or rutile). Structural data proved that incorporation of different chromophore ions into the karrooite structure affects unit cell parameters, bond length distances and angles, site occupancies and therefore cation order–disorder. Optical spectra exhibit broad absorbance bands of Co(II), Cr(IV), Fe(III), Mn(II), Mn(III), Ni(II), V(IV) with distinct contributions by cations in the M 1 and M 2 sites. Karrooite pigments have colours ranging from orange to brown-tan (Cr, Fe, Mn, V) to green (Co) and yellow (Ni) that are stable in low-temperature (<1050°C) ceramic glazes and glassy coatings. [Copyright &y& Elsevier]