Search

Energy-dispersive x-ray spectroscopy and high-angle annular dark-field in a Cs-corrected scanning transmission electron microscope are employed to characterize the atomic-scale strain distribution in the active region of the InAs-based interband cascade laser. For the first time, energy-dispersive x-ray spectroscopy is utilized for the quantitative calculation of the zero-strain region, by which the geometric phase analysis of high-angle annular dark-field imaging has been carried out. The strain distribution of the active region with high accuracy has been obtained. The analysis of the out-of-plane strain shows that the active region in the InAs-based interband cascade laser is strain-compensated, while a certain degree of elemental intermixing still exists in the active region. This detailed strain distribution can provide valuable insights into the optimization of the growth conditions for the active region such as growth temperature, V/III flux ratio, and growth process to minimize the elemental intermixing and obtain a better performance interface while maintaining the strain-compensated state. [ABSTRACT FROM AUTHOR]

In the study, the effects of hybrid reinforcement (nano-alumina and MWCNT) and heat treatment on the wear behavior of the Al–4Cu nanocomposites were investigated under dry sliding condition against W–6Co ball by means of a ball-on-disk type tribometer. The load and the sliding speed were kept constant and selected to be 10 N and 0.1 m s−1, respectively, in the course of the wear tests. Meanwhile, the wear tests were completed after a total sliding distance of 1500 m was reached for each case. During these tests, the wear loss of the nanocomposites was measured at every 250 m. The worn surfaces of the nanocomposites were examined with the help of stereo and scanning electron microscopes. The volumetric wear rates, wear coefficients and wear mechanisms were identified for the nanocomposites to clarify the influence of reinforcement content and heat treatment on their wear resistance. The volume loss at the wear distance of 1500 m was obtained as 24.9 and 8.2 mm3 for the annealed and aged Al–4Cu alloy, respectively. On the other hand, it decreased to 4.6 and 3.2 mm3 in the case of the nanocomposites with 15% hybrid reinforcement in the annealed and aged conditions, successively. Moreover, increasing the hybrid reinforcement amount decreased the wear loss of the aged nanocomposites substantially in such a way that it resulted in the mild wear. [ABSTRACT FROM AUTHOR]

This study aims to investigate the microstructural, mechanical, and tribological characteristics of Al-nano TiC composites. The microwave-sintered nanocomposites were analyzed using optical and scanning electron microscopes, providing valuable insights into the spatial distribution and interaction of TiC within the matrix material. Microstructure characterization confirmed the uniform dispersion of nano TiC particles throughout the Al. Furthermore, the microwave-sintered nanocomposite samples displayed greater hardness than pure aluminum, indicating the strengthening impact of nano-TiC. Al-6 wt.% nanocomposites fabricated using microwave-sintered powder metallurgy showcased an impressive hardness rating of 51 VHN. The assessment of tribological properties revealed that a higher TiC concentration reduced wear rate, showcasing improved surface protection. However, it was observed that the friction coefficient rise with the addition of nano-TiC particles, implying changes in the bonding between the composite and the interacting surface. The thorough examination of worn surfaces yielded insights into the wear mechanisms present in the nanocomposite materials. Detailed examination of worn surfaces highlighted the formation of protective oxide layers, contributing to the improved wear resistance. This research contributes to our understanding of the complex interactions occurring during tribological processes by clarifying the morphological features of worn surfaces. [ABSTRACT FROM AUTHOR]

The necessity to adapt sustainable development, green chemistry and industrial ecology leads to the creation of newer materials and the utilization of waste. In this context, this work aims at exploring the feasibility of the fabrication of hybrid composites comprised of a polymeric resin reinforced with a natural fiber (hemp) and an industry waste filler (dolomite dust). While the hemp fiber content is kept constant, epoxy‐based hybrid composites are fabricated with different weight percentages of dolomite dust using the conventional hand lay‐up route. The microstructural features of the constituent materials are studied using stereo and scanning electron microscopes which show the shape and size of dolomite particles and the arrangement of fibers. An x‐ray diffraction analysis revealed the presence of hematite, graphite, lime and manganite. The presence of functional groups like hydroxyl, carboxyl and azide is ascertained from the transmittance spectra of Fourier transform infrared spectroscopy. The density and void fractions are increasing with the amount of filler particles in the composite. It is observed that the tensile and flexural strengths of the composites marginally drop with increase in dolomite dust content, but there is a reasonable improvement in their inter‐laminar shear strength, micro‐hardness and impact strength values. [ABSTRACT FROM AUTHOR]

The high source stability and brightness of field emission gun equipped scanning electron microscopes (SEM) makes them ideal for high‐resolution digital image correlation (HRDIC). However, their high initial capital cost can be prohibitive for research organisations and groups. Conventional thermionic SEMs using either a tungsten hairpin or LaB6 filament are far more widespread due to their lower cost. Whilst it is understood that overall performance and ultimate resolution are lower than field emission SEMs, we propose that there is no fundamental reason why these instruments are unsuitable for HRDIC. We investigate the use of a LaB6 SEM as a viable tool for HRDIC. We detail the subtleties of performing HRDIC using a LaB6 thermionic source SEM, providing technical recommendations for best practices in using these instruments for strain mapping. The effects of instrument parameters on strain measurement noise are examined, with a focus on parameters of key relevance to in situ and ex situ mechanical testing. Errors in focus and image pixel size are found to be the primary contributors to the strain noise floor values, with stage accuracy being of secondary importance. We present a case study in oxygen‐free high‐conductivity copper, OFHC‐Cu, which is used in the designs of nuclear fusion components as a heat sink interlayer. Heterogeneous strain patterns are observed in this material, with high levels of strain localisation at grain boundaries. Active slip systems are identified using the relative displacement ratio method, demonstrating the quality of these data and the suitability of LaB6 instruments for HRDIC strain mapping, achieving performance approaching that expected of a field emission SEM. [ABSTRACT FROM AUTHOR]

The studies presented in this paper constitute the first scientific attempt to interpret the manner whereby notched implements made of scapulae were made and used. These implements have been found at numerous European and non-European sites, usually dated to the Neolithic–Early Iron Age (predominantly the Early Bronze Age). Research has examined these products since the beginning of the 20th century, resulting in the development of several hypotheses regarding their functions. This paper presents the analysis results of 41 such artefacts from the early Bronze Age defensive settlement in Bruszczewo (central Poland). This is the largest collection of these products from a single site worldwide. The artefacts were subjected to multi-aspect traceological tests (both technological and functional) using optical, metallographic, and scanning electron microscopes. The residues identified on their surfaces were analysed using optical microscopy and scanning electron microscopy and energy dispersive X-rays spectroscopy. Moreover, the studies reported herein involved extensive experimental research. Consequently, the chain of operations followed in producing these tools was reconstructed and the use-wear traces present on their surfaces were classified; it was determined that these tools were most likely used for threshing cereals but might also have been used for threshing legumes. This is the first proof of threshing in central Europe in the Early Bronze Age and the first scientifically substantiated hypothesis regarding the function of these important artefacts. [ABSTRACT FROM AUTHOR]

Parasites pose significant challenges to aquaculture and fisheries industries. Our study focuses on the Polyonchobothrium magnum and African catfish to address a potential health issue in aquaculture, explore host–parasite interactions that can help develop effective management practices to ensure fish health and industry sustainability. P. magnum was isolated from the stomach of African catfish (Clarias gariepinus) as the primary site of infection, with a prevalence of 10%. Most affected fish were heavily infected (8 out of 10). Infection was confirmed by sequencing the PCR‐targeted region of the nicotinamide adenine dinucleotide dehydrogenase subunit 1 (ND1) gene, along with light and scanning electron microscopes. The parasite had an elongated scolex with deep bothria, a prominent apical disc wider than the scolex itself, and a four‐lobed appearance. The scolex contained a central rostellum divided into two semicircles, bearing 26–30 hooks, with an average of 28. The apical disc had large hooks arranged in four quadrants, with 6–8 hooks each, averaging 7 per quadrant. No neck was observed. Phylogenetic analysis of our sequence showed a 100% match with isolates from Guangzhou, China. In infected fish, the anterior kidney showed increased expression levels of nuclear factor kappa B and lysozyme, but decreased levels of in major histocompatibility complex antigen II. Plasma analysis revealed a significant drop in superoxide dismutase, a rise in interleukin‐1 beta, and lower IgM levels compared to non‐infected controls. Non‐infected fish displayed greater gut microbiota diversity, with dominant families including Moraxellaceae, Enterobacteriaceae, Fusobacteriaceae, and Caulobacteraceae, and prevalent genera such as Acinetobacter, Cetobacterium, and Brevundimonas. In contrast, infected fish exhibited very low diversity, with significantly higher proportions of Enterobacteriaceae (45.99%) and Aeromonadaceae (41.79%) compared to non‐infected fish, which had 13.76% and 3.64% respectively. Cetobacterium somerae was prevalent in non‐infected fish, while infected fish harboured Aeromonas fluvialis, Plesiomonas shigelloides, and Gallaecimonas xiamenensis. Overall, P. magnum disrupted the immune status and gut microbiota of the host, thereby impacting its health. [ABSTRACT FROM AUTHOR]

Automated mineralogy is a software addition usually seen on scanning electron microscopes designed to provide rapid insight into sample chemistry and texture in routine petrology workflows. The specific purpose of automated mineralogy is to provide mineral classifications to uniquely identified phases typically using energy dispersive spectroscopy, thus removing laborious and time‐consuming human input for routine tasks. These mineral classifications can then be applied to image data to quantify which mineral is associated with any particular texture. Automated mineralogy systems were primarily designed to generate quantitative textural analysis of particle samples to the mining industry and have remained a critical technique in this setting for the last several decades. Automated mineralogy has become more widely used in academia, and this has changed the focus of the technique, applying it to a broader range of workflows and applications. Here we show petrology examples focussing where combined geochemical and textural analysis are widely used. Critically, the use of quantitative geochemical data means that mineral classifications are based on their quantitatively measured chemistry. By making both the chemical and textural analysis quantitative, automated mineralogy can become highly flexible and provide a unique system for petrologists in both industry and academia. [ABSTRACT FROM AUTHOR]

The concept of zoom in scanning electron microscopy (SEM) once referred to increasing the magnification of the sample by reducing the scanned field size. However, with the introduction of digital technology, the concept of zooming has become a little more complicated. Historically, older SEMs operated at a 512 × 512-pixel lateral resolution (262 kB pixel density) at TV scan rates. Today's newest SEMs can achieve up to 32k × 24k (4:3 ratio) pixel lateral resolution, equating to an 805 MB pixel density. In this article, we explore the factors involved in selecting an appropriate frame grabber size for SEM imaging. Specifically, we will delve into the implications of pixel density, including its impact on digital zoom capabilities, image file sizes, and overall image acquisition times. [ABSTRACT FROM AUTHOR]

Basalt is a widely used raw material for tool manufacture at prehistoric sites, but a unified methodology for assessing how hominfins used basalt in prehistory is lacking. A comprehensive experimental investigation of basalt tools is, thus, necessary to establish a reliable methodological framework that can be used to explore the functional properties of archaeological basalt assemblages. The aim of this study is to contribute to the development of a methodological framework for the analysis of use-wear on basalt tools. Basalt, characterised by its distinct mechanical and structural properties and unique response to mechanical stress, requires specialised treatment and investigation. To address this, our basalt varieties were characterised using SEM–EDS analysis. Sequential experiments were conducted, using the experimental basalt tools in different activities, including butchery, hide, bone and woodworking to determine use-wear formation patterns. Subsequentially, various analytical tools, including optical and scanning electron microscopes, were used to analyse macro- and micro-wear traces on basalt. Our results provide useful information on methodological aspects of use-wear formation on basalt. The inclusion of detailed cleaning and experimental protocols enhanced the robustness of our methodology. Furthermore, the combined utilisation of various microscopes enabled to compile a comprehensive and complementary information on such a complex raw material such as basalt and to characterise thoroughly the diagnostic features of the micro-wear traces (e.g. edge damage, rounding, polish). [ABSTRACT FROM AUTHOR]

Maize (Zea mays) was a fundamental part of the diet for the Classic period Maya (ca. 250–900 CE) and other Mesoamerican societies. Nixtamalization, the process whereby maize is cooked in an alkaline solution, is important as it enhances the nutritional value of maize, among other reasons. However, documenting this process in the archaeological record is not straightforward. A microbotanical study of residues collected from ceramic vessels and grinding stones from Late Classic (ca. 600–900 CE) contexts at the Lowland Maya site of La Corona (Peten, Guatemala), revealed the presence of starch spherulites. Their authenticity was confirmed by polarized microscopy and Scanning Electron Microscope (SEM) imaging combined with iodine staining. We argue that nixtamalization as a cooking technique was occurring at La Corona during the 7th and 8th centuries CE. We present evidence from ceremonial contexts, specifically burial and feasting/commensal events. This is the earliest evidence of lime-treated maize in the Maya area recovered directly from ceramic vessels linked to preparation and/or consumption of food. [ABSTRACT FROM AUTHOR]

This investigation aimed to study the effects of ZnO-added fluorophosphate glass on in vitro degradation, apatite-forming ability, cytotoxicity, antioxidant efficacy, and antibacterial activity. In this regard, fluorophosphate glasses with varying zinc oxide (ZnO) content (0, 1, 2, 4, and 8 mol%) were synthesized by the standard melt quenching technique and subsequently in vitro degradation of the glass samples was analyzed by water solubility test. The apatite-forming ability of the glasses was studied by simulated body fluid (SBF) immersion analysis. Variations in the elemental and structural properties of the glasses before and after SBF immersion were assessed using an X-ray diffractometer, a Fourier transform infrared spectrometer, and a scanning electron microscope coupled with energy-dispersive X-ray spectrometer. The cytotoxicity assessment for ZnO-added fluorophosphate glasses was evaluated using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method. The antioxidant efficacy of the glass samples was evaluated using 2,2-diphenyl-1-picrylhydrazyl assay. Variations were observed in lower concentrations of ZnO compared to higher concentrations in mechanical, structural, and biological properties. Amongst the concentrations, 2 mol% ZnO-added fluorophosphate glass demonstrated superior antioxidant activity compared to the zinc-free fluorophosphate glass. The optimized 2 mol% of ZnO was evaluated against different bacterial strains such as Escherichia coli , Klebsiella pneumonia , Proteus vulgaris , Staphylococcus epidermidis , Pseudomonas aeruginosa , and Staphylococcus aureus using the agar diffusion method. A distinct transparent inhibitory zone was observed against all the bacterial strains, following exposure to the 2 mol% of ZnO containing fluorophosphate glass compared to the zinc-free glass sample. These findings suggest that 2 mol% of ZnO containing fluorophosphate glass is well-suited for biomedical applications involving cellular activity. [ABSTRACT FROM AUTHOR]

The low field magnetic susceptibility (χLF) measured in the 1116‐m‐long Dévaványa core (Pannonian Basin) is a quasi‐continuous record of the Plio–Pleistocene Mid‐European mountain permafrost development. The continuity of fluvial conditions is confirmed by seismic data, and the detrital origin of magnetite is indicated by frequency‐dependent susceptibility measurements, scanning electron microscope, and hysteresis investigations. The χLF record is correlated to the δ18O curve (LR04) supported by palaeomagnetic data. The colour of samples documents precession and obliquity cycles in local facies variations, but the χLF indicates the dominance of 100‐ka eccentricity cycles in the linked mountainous permafrost events. Comparison with orbital solutions revealed that the long‐term development of permafrost occurs as a result of amplitude modulation of the 100‐ka eccentricity cycles. Increases in amplitude of the 100‐ka cycles inhibits permafrost development due to shortened winters. Thus, if extremes are present, the permafrost regions are limited or disappear, but if the 100‐ka eccentricity cycles are attenuated, permanent frost can extend into the temperate zone. This amplitude modulation may also be responsible for the early glaciations during the Pliocene, for the intensification of Northern Hemisphere glaciation, foreshadows cooling in the forthcoming 405‐ka term, and allows the change from 41‐ka cycles to 100‐ka ones in the Mid‐Pleistocene Transition to be explained. The 41‐ka cycles are the result of obliquity‐controlled changes close to the polar cycles, while 100‐ka cycles occur when the amplitude attenuation of the 100‐ka eccentricity cycles enables extended glaciations that suppress the regular 41‐ka cycles. Higher mountains in the catchments enable higher resolution of permafrost records documenting even smaller glaciations. However, the similarities in the overall trends in χLF records of catchment areas with 1500‐m difference in their altitude is a potential counter‐argument when considering the role of tectonic elevations in the expansions of mountainous permafrost. [ABSTRACT FROM AUTHOR]

An efficient method to accelerate the use of polymer composites is to focus on their development as environmentally friendly materials that can naturally break down without causing any harm to the ecosystem. Hence, the primary aim of this study is to develop a biocomposite material through the fusion of Sesbania rostrata (SRF) bark fibers and the polycaprolactone (PCL) biopolymer. Various percentages (10, 15, 20, and 25 wt.%) of untreated and sodium bicarbonate‐treated SRF were incorporated into polycaprolactone to create the biocomposite samples. The composite panels were made using the compressing molding technique. Several tests were performed on the samples, such as mechanical, thermal, water absorption, wear, and morphological tests. Research has demonstrated that the strength of biocomposites composed of 20% chemically treated SRF and PCL is superior to that of other mixed materials. The thermal properties of the biocomposite remained unchanged when untreated fibers were included, but they improved when treated fibers were included. Higher water absorption properties are attributed to an increased fiber volume fraction in the biocomposites, while chemically treated fibers exhibit a notable improvement in water resistance. The wear test results indicate that the weight loss of the biocomposites is mainly influenced by the contact temperature and adhesion between the SRF surface and the PCL matrix. When examining the fractured biocomposites with a scanning electron microscope (SEM), it becomes evident that the primary reasons for failure are fiber pull‐out, debonding, and agglomeration. Highlights: SR Natural fiber is chemically treated by eco‐friendly sodium bicarbonate.The treated SRF‐reinforced composites had best mechanical property.The treated SRF‐reinforced composites showed less water absorption.The composite mechanical and thermal properties had dropdown at 25 wt.% SRF.The addition of SRF reduced the weight loss of composites on wear test. [ABSTRACT FROM AUTHOR]

The current research involved the synthesis of zinc oxide nanoparticles (ZnO-NPs) using an aqueous extract of Helichrysum cymosum shoots, and subsequent characterization via different analytical methods, such as UV–Vis spectroscopy, Scanning electron microscope (SEM), Energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Transmission electron microscope (TEM), and zeta potential. The biological effects of the ZnO-NPs were then tested against C3A hepatocyte cells and L6 myocyte cell lines via series of analysis, including cytotoxicity, antioxidant, anti-inflammatory, and antidiabetic effect via enzymatic inhibition. The UV–Vis analysis showed a maximum absorption spectrum at 360, and the TEM analysis reveals a spherical and hexagonal structures, with an average dimension of 28.05–58.3 nm, and the XRD reveals a crystalline hexagonal structure. The zeta potential evaluation indicated that the ZnO-NPs are relatively stable at − 20 mV, and the FTIR analysis identified some important functional group associated with phenolics, carboxylic acid, and amides that are responsible for reducing and stabilizing the ZnO-NPs. The synthesized ZnO-NPs demonstrated cytotoxic effects on the cell lines at higher concentrations (125 µg/mL and 250 µg/mL), complicating the interpretation of the results of the inflammatory and antioxidant assays. However, there was a significant (p < 0.05) increase in the inhibitions of pancreatic lipase, alpha-glucosidase, and alpha-amylase, indicating beneficial antidiabetic effects. [ABSTRACT FROM AUTHOR]

Background Objective Methods Results Conclusion Neuromodulator injections are minimally invasive procedures performed across the globe. Despite their ubiquity, there is a dearth of information on whether and how needle tips used for neuromodulator procedures are deformed after repeated injections.We investigated the magnitude of needle tip deformation following sequential injection passes (3×, 5×, and 10×) during facial neuromodulator injections with three commonly used needle sizes (30G, 31G, and 32G).Neuromodulator was administered for four different aesthetic indications. Each collected needle was mounted and imaged in a Philips XL‐30 Scanning electron microscope. Images were processed using ImageJ photo analysis software.Forty‐five needle tips were investigated. When comparing the facial regions of interest, a statistically significant difference in deformation percentage was found when injecting 10× (p = 0.044) with greatest damage after injecting the glabella (38.4%), followed by lateral canthus (27.9%), forehead (27.5%), and midface (23.1%). Independent of facial region targeted, the mean percentage of needle deformation at 3× was 14.8%, at 5× 19.6%, and at 10× 29.2% with p < 0.001. Smaller needle size corresponded to smaller percentage of damage.Exchanging needles after more than five injection passes will minimize needle deformation and likely increase injection precision. [ABSTRACT FROM AUTHOR]

Zirconolite-based structures have served as robust matrices for the incorporation of minor actinide-rich high-level waste (HLW). The co-doping effects are critical for exploring the phase evolution of zirconolite-based structures, thereby providing a guide for HLW immobilization. Nevertheless, few studies have studied the synergistic effect of high valent ion W6+ and Lanthanides (Ln, surrogates to minor actinides) co-doping. This study proposed a systematical study on the Ln-W (Ln = Nd, Sm, Gd, Ho, Yb) co-doping in zirconolite-derived structure using X-ray diffraction (XRD) and scanning electron microscope with energy dispersive X-ray spectroscopy (SEM-EDX). The results showed that near-single-phase zirconolite-2M was recorded for samples with low level doping of Ln-W (Nd–W, Sm–W and Gd–W with x = 0.05; Ho–W and Yb–W with x = 0.05–0.1), and its structure underwent a moderate expansion along the c-axis, as revealed by a Pawley refinement method. One key finding is that near-single-phase zirconolite-2M was recorded for samples with low level doping of Ln-W (Nd–W, Sm–W and Gd–W with x = 0.05; Ho–W and Yb–W with x = 0.05–0.1), and its structure underwent a moderate expansion along the c-axis, as revealed by a Pawley refinement method. Notably, in addition to a transformation from zirconolite-2M to pyrochlore, a pseudo-yellow phase CaWO 4 was also noted with increasing co-doping contents. This work demonstrates that the high charge compensator W6+ and lanthanides can be simultaneously incorporated into zirconolite structure, and a different phase transformation was revealed compared to that in low valent element doping system, which gives a new insight into the optimization of HLW immobilization route. [ABSTRACT FROM AUTHOR]

Studies of astromaterials provide valuable insights into the formation and evolution of the solar system. To analyze such astromaterials on a sub-micrometer scale, one of the most useful tools is energy-dispersive X-ray spectroscopy (EDS) in conjunction with scanning transmission electron microscope (STEM). The conventional semiconductor-based EDS system is sometimes insufficient to resolve emission lines at closely adjacent energies. A transition edge sensor (TES) X-ray microcalorimeter is a promising solution to overcome this problem. We developed a 64-pixel TES X-ray microcalorimeter array which had an energy resolution of approximately 7 eV (FWHM) at an energy band from B Kα to Cu Kα. However, the counting rate was only approximately 1000 count/s/array. The distance between the detector and the sample is 30 cm, limited by the stage of the refrigerator. Therefore, an X-ray polycapillary is used to focus the X-ray, which focus size is 5 mm in diameter, resulting in a detection efficiency of only 5%. To increase the effective area, we developed a large size absorber with a large-scale array. A three-dimensional structure was created to fill the dead space between TES pixels. Additionally, an array of 224 elements was made to increase the detection efficiency by a factor of 10. In this paper, we provide more details of design, fabrication process of the overhang absorber, and device performance. [ABSTRACT FROM AUTHOR]

We present confirmation, with exact locality data, of the presence in Turkey of Acmenychus inermis. The presence in Türkiye of all Acmenyhus Weise, 1905 species has been reported mostly as generically in Anatolia without exact locality data up to now. Thus, the presence in Turkey of Acmenychus inermis (Zoubkoff, 1833) is confirmed with exact locality data for the first time. The Acmenychus species found on wheat plants from Çorum province is one of the three species of this genus found in the western palearctic. We provide both a genus key of the Turkish Hispini tribe and a species key of the genus Acmenychus. Scanning Electron Microscope (SEM) images of the elytra, pronotum, antennae, head, and male genitalia (Aedeagus) of Acmenychus inermis are provided. Detailed pictures of this species are also included in this study. [ABSTRACT FROM AUTHOR]

The earliest silicon-based aerogels attracted attention due to their nanoscale porous structure and high transparency. Still, they need to be more balanced with the poor mechanical properties. Their brittle structure limits the development of this promising new material. Therefore, the goal of this work is to optimize the mechanical properties of aerogels while maintaining transparency. The good mechanical properties of polymers have made them the material of choice for this work. Polyvinyl alcohol (PVA), which can undergo self-crosslinking through side-chain hydroxyl groups forming hydrogen bonds, was chosen as the raw material to simplify and expedite the production process. The production process was experimented with, analyzed, and refined. Considering the time efficiency of the experimental process, a one-step gelling method was invented to facilitate the sol-gel transition. The one-step gelling method maintained the high transparency of PVA aerogels and reduced the time required for the gelation process compared to the freeze-thawing method. This work employs carbon dioxide supercritical drying to ensure minimal structural collapse and maximize the porous structure's retention. The transmittance of PVA aerogels can reach up to 93.67% at a wavelength of 1333 nm. The internal structure of aerogels with different PVA concentrations was observed using a Scanning electron microscope. Applying Beer-Lambert's Law eliminated the effect of sample thickness on transparency. The relationship between the transparency of PVA aerogels, their microstructure, and macroscopic concentration was studied and analyzed for the first time. While ensuring light transmittance, the modulus of the PVA aerogel reached as high as 6.18 ± 0.56 MPa at 13 wt%. [ABSTRACT FROM AUTHOR]

Frankliniella occidentalis, western flower thrips, is an invasive pest that seriously damages economic crops such as vegetables, flowers, and fruit trees because of its high fecundity, short generation cycle, and strong adaptability. Lecanicillium is an important entomopathogenic fungus, characterised by its wide host range, high pathogenicity, and environmental safety. It plays an important role in the environmentally friendly management of F. occidentalis. This study clarifies whether L. attenuatum infects F. occidentalis and affects its reproduction. The results of scanning electron microscope showed that conidia of L. attenuatum were attached to many parts of thrips adult after 1 h of treatment with 10^8 conidia/mL, and most F. occidentalis were covered by hyphae after 72–120 h. The cumulative mortality rate of the second instar larvae of the F1, F2, and F3 generations exceeded 60% on the seventh day post-infection and that of female adults was higher than 90% when treated by L. attenuatum with 10^8 conidia/mL. Simultaneously, L. attenuatum had strong sublethal effects on the surviving thrips. Indeed, the number of eggs deposited and the lifespan of female adults decreased considerably after the second instar larvae of F. occidentalis were treated with L. attenuatum, and had the impaction on the thrips offspring too. Altogether, our data suggested that L. attenuatum not only exhibited a high degree of pathogenicity towards F. occidentalis second instar larvae and adults but also affected the longevity and reproduction of surviving thrips. [ABSTRACT FROM AUTHOR]

Herein, laboratory experiments are conducted to evaluate the effect of sulfur and lanthanum content in the steel on the modification of inclusions. The amount, composition, morphology, and size of nonmetallic inclusions in the steel are observed using an automatic scanning electron microscope. Results show that as the lanthanum content in the steel increased from 0 to 72 ppm, the inclusions in the steel with 12 ppm sulfur are modified in the following order: Al2O3–CaO–MgO → LaAlO3 → LaAlO3–La2O2S → La2O2S. Similarly, when the sulfur content is 27 ppm, inclusions transformed in the order of Al2O3–CaO–MgO → LaAlO3 → LaAlO3–La2O2S → La2O2S → La2O2S–LaxS → LaxS as the lanthanum content increases from 0 to 150 ppm. Thermodynamic analysis using FactSage based on a private database is employed to reveal the mechanism for the modification of inclusions. Additionally, a kinetic model is established to study the transformation rate of inclusions in the steel after the addition of lanthanum and sulfur. Liquid Al2O3–CaO–MgO inclusions disappear after 800 s when the steel contains 12 ppm sulfur and 12 ppm lanthanum. The composition of inclusions is 53%LaAlO3–47%La2O2S at 1800 s, while it is 100%La2O2S and 80%La2O2S–18%LaxS–2%CaS when the lanthanum content is 33 and 72 ppm, respectively. [ABSTRACT FROM AUTHOR]

This study proposed a novel hybrid joining technique that combines through-thickness reinforcement (TTR) and induction welding methods to address the challenges of composite-metal joining. The effects of geometrical parameters of micro-pins on the formation and bearing performance of hybrid joints were investigated by combing the experimental and numerical simulation approaches. Two simulation models which included the induction heating transfer and joint tensile failure process were established by COMSOL Multiphysics and Abaqus/Explicit. Subsequently, digital image correlation (DIC) was used to monitor the deformation process of different types of joints under tensile load, and a scanning electron microscope (SEM) was used to observe the welding interface of failed joints. By comparing the experimental and simulation results, it is found that adding pins can significantly improve the mechanical performance of welded joints, with maximum increases of 159% and 1758% in ultimate strength and energy absorption respectively compared to welded joints without interlock structures. This technique presents a potential solution for achieving high-quality metal-composite welded structures. [ABSTRACT FROM AUTHOR]

This article aims to evaluate and compare two types of organic surface-modified-nanoclay of octadecylamine-modified-bentonite-nanoclay (ODA-BNC) and aminopropyltrimethoxysilane-octadecylamine-modified-nanomontmorillonite (APS-ODA-MMT). Each type of nanoclay is combined with silica as a bi-filler for natural rubber (NR)/ethylene propylene diene monomer rubber (EPDM) in a 50/50 blend ratio for possible vulcanized rubber nanocomposite application. The total filler content is 50 phr while nanoclay filler content ranges from 0 to 20 phr, keeping the other ingredients ratio fixed. The prepared composites are characterized by the Fourier transform infrared spectrophotometer (FTIR) and their mechanical and thermal properties are thoroughly investigated. The data reveal that the fillers added to the rubber can improve its surface properties according to their type and amount as confirmed by the Atomic force microscope (AFM), and Scanning electron microscope (SEM) investigation. The surface of rubber containing APS-ODA-MMT displayed higher height (251) and roughness surface (94.11), than those (69.8) and (45.62) respectively, containing ODA-BNC. Moreover, the acid resistance of the prepared composites is verified and indicated that increasing the nanoclay ratio (20%) enhances the acid resistance by reducing the surface distortion while keeping the surface morphology. The mechanical properties and Thermogravimetric Analysis (TGA) measurements showed that the rubber containing ODA-BNC has higher values of stress (2.2), elongation (975), and thermal stability (470, 505, 520°C) than those (1.75), (650), and (440, 460, 470°C) respectively, containing the APS-ODA-MMT. Moreover, the durability investigation of the vulcanized rubber via the AFM found the modified composites can be used in harsh environments as a covering layer in petrochemical networks or chemical factories. [ABSTRACT FROM AUTHOR]

Objective: Emerging evidence suggests that the endometrial microbiome plays important roles in the development of endometrial cancer (EC). Here, we evaluate stage‐specific roles of microbial dysbiosis and metabolic disorders in patients with EC, patients with endometrial hyperplasia (EH), and patients afflicted with benign uterine conditions (CK). Methods: This prospective cohort study included 33 women with EC, 15 women with endometrial EH, and 15 women with benign uterine conditions (CK) from November 2022 to September 2023. Different typical endometrial samples were imaged with a scanning electron microscope and a transmission electron microscope. The endometrial microbiome was assessed by sequencing the V3–V4 region of the 16S rRNA gene and the ITS1 to fill the gap in relation to the study of the uterine fungal microbiome. Moreover, liquid chromatography‐mass spectrometry‐based metabolomics was used to identify and quantify metabolic changes among these groups. Results: The endometrial microbiome revealed that there is a structural microbiome shift and an increase in the α‐diversity in the EC and EH cases, distinguishable from the benign cases, especially the fungal community structure. The fungal microbiome from patients with EC and EH was altered relative to controls and dominated by Penicillium sp. By contrast, Sarocladium was more abundant in controls. Significant differences were observed in the composition and content of compounds between benign cases and EC, especially estradiol‐like metabolism‐related substances. Altered microbiota was correlated with the concentrations of interleukin‐6 (IL‐6), IL‐11, transforming growth factor‐beta, and β‐glucuronidase activity especially the relative abundance increase of Penicillium sp. Conclusions: This study suggested that the endometrial microbiome is complicit in modulating the development of EC such as estrogen activity and a pro‐inflammatory response. Our work provides a new insight into the endometrial microbiome from a perspective of stages, which opens up new avenues for EC prognosis and therapy. Synopsis: This study suggested that the endometrial microbiome is complicit in modulating the development of endometrial cancer. [ABSTRACT FROM AUTHOR]

Baicalein and wogonin, two health-promoting flavonoid aglycones in Scutellaria baicalensis Georgi roots, have better bioactivity and bioavailability than their glycoside precursors (baicalin and wogonoside). The search for novel microorganisms for the fermentation of S. baicalensis roots to improve the yields of baicalein and wogonin is of great interest in the food and nutraceutical industries. In this study, a novel endophytic fungus (Penicillium rubens) capable of producing cellulase (0.82 ± 0.12 U/mL) and β-glucosidase (4.55 ± 0.97 U/mL) was used to ferment S. baicalensis roots to obtain high yields of baicalein and wogonin. Semi-solid-state fermentation with homogeneous fungal cultures was found to be the appropriate strategy. Under the optimal fermentation parameters (temperature 30 °C, inoculation dose of fungal cultures 4 mL/g, and time 60 h), the yields of baicalein and wogonin (46.95 ± 4.98 mg/g DW and 31.41 ± 9.36 mg/g DW) from S. baicalensis roots were tremendously increased by 16.13-fold and 15.47-fold over control, respectively. Results of industrial enzyme bioprocessing and scanning electron microscope indicated that the remarkable increase in aglycone product yields could be due to the synergistic effects of cellulase and β-glucosidase produced by P. rubens on cell wall hydrolysis and glycoside deglycosylation. In addition, extracts of S. baicalensis roots fermented by P. rubens showed a significant increase in antioxidant and antimicrobial activities. Overall, the semi-solid-state fermentation of S. baicalensis roots using the novel P. rubens was an effective strategy that could yield high quantities of baicalein and wogonin, which had promising potential in the food and nutraceutical industries. [ABSTRACT FROM AUTHOR]

The structural and luminescence properties of the Lu 3 Al 4 Sc 1 O 12 :Pr and Gd 3 Al 3 Sc 2 O 12 :Pr garnet scintillators co-doped with boron (B3+) ions were investigated. The addition of B3+ and Sc3+ to the structure has a positive effect on the luminescence properties, especially on the photo, radio emission intensities, quantum efficiency, and results in a reduction of the decay time, which is necessary for high-quality scintillators. Structural properties of garnets have been determined after X-ray diffraction analysis coupled with Rietveld refinement. Surface morphology analysis was performed using a scanning electron microscope and particle size was also determined. Elemental composition was confirmed by the ICP-OES technique. Reflection, excitation (in the UV and VUV range), emission (upon excitation by UV or X-rays), decay time, and quantum efficiency at room temperature were measured. Furthermore, the influence of temperature on excitation, emission, and decay curves was also analyzed. The obtained luminescence properties indicated positive effect caused by doping. [Display omitted] [ABSTRACT FROM AUTHOR]

Acidic conditions affect the archaeological bone in the burial and in uncontrolled display and storage environment or due to improper restoration processes. Accordingly, bones become weak and fragile. This study aims to evaluate nano calcium propionate and nano styrene butyl acrylate (used for the first time in the treatment of bones) at different concentrations for deacidification and consolidation of fragile bones. New bone samples were prepared. Artificial accelerated aging (acid and heat) was applied to prepare aged untreated samples. Deacidification and consolidation processes using the materials mentioned above were applied. The analytical techniques used were transmission electron microscope (TEM) and thermal gravimetric analysis (TGA) were used for morphological and thermal stability investigation for the prepared nano styrene butyl acrylate copolymer and its calcium propionate nonocomposites, a digital microscope and scanning electron microscope (SEM) for investigation of the surface morphology, pH value measurement, change of color measurement, attenuated total reflection—Fourier transform infrared spectroscopy (ATR/FTIR), contact angle (wettability), and X-ray diffraction analysis for measurement of bone crystallinity. The results proved that acid-heat aging affected bone properties such as changes in surface morphology and color, decrease in pH value, and contact angle. Bone samples became more crystalline, and the chemical composition of bone was also affected. The treatment of aged untreated bone samples with the materials used in this study improved their properties, such as increasing the pH value and contact angle. The surface morphology, color change, and crystallinity of bone improved and became more stable. [ABSTRACT FROM AUTHOR]

We report the results of an international interlaboratory study of the flexural strength of alumina fabricated across six laboratories using the vat photopolymerization ceramic additive manufacturing (AM) technology. The mechanical testing of all the specimens, 142 in total, was performed at the National Institute of Standards and Technology (NIST) according to the well‐established four‐point bending method standardized for traditional ceramics. Overall, the existing ASTM standard for the four‐point bend testing proved adequate for AM ceramics, with several modifications to the specimen requirements to account for the specifics of AM processes. Critical flaws that caused failure were identified in all but two cases using optical fractography augmented with the imaging of fracture surfaces in a scanning electron microscope. The flexural strength data, analyzed following the Weibull statistics, exhibited considerable variation among the specimen sets manufactured by different laboratories. This variability correlated with the presence of many distinct critical flaws. We identified seven types of flaws that accounted for the failure of 94% of specimens. The prevalent flaws depend on the printing direction relative to the specimen's geometry. We discuss the nature of these flaws and their relation to the printing and post‐processing conditions. Removal of several types of critical flaws will significantly improve mechanical properties of ceramic parts built using vat‐photopolymerization AM. [ABSTRACT FROM AUTHOR]

Lanthanum Strontium Cobalt Ferrite Oxide (LaSrCoFeO 3) has been widely used as cathode material for intermediate-temperature solid oxide fuel cells at the temperature of 500–800 °C. At this temperature range, understanding the electrochemical behavior which is commonly analyzed by complex nonlinear least-squares (CNLS) analysis is very crucial in improving the cathode's performance. However, this analysis shows some limitations in interpreting the electrochemical processes in detail, particularly at the electrode-electrolyte interface. Hence, this study is conducted to compare the electrochemical impedance data analyses by CNLS and the distribution of relaxation times (DRT) of a fabricated LaSrCoFe|BCZY|LaSrCoFe (LaSrCoFe La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 and BCZY=BaCe 0.54 Zr 0.36 Y 0.1 O 2.95) symmetrical cell. Impedance data of the cell is collected at T = 800 °C at two different stabilization times and to further enhance the analysis process, the impedance data of the cell at measurement temperatures of 700 °C and 750 °C are also included. In a Nyquist plot, the cell exhibits depressed semi-circles that represent a few processes occurring at the interface. The DRT analysis is more precise and easily reveals the semi-circles consisting of four different sub-processes (represented by four peaks) than CNLS (represented by four impedance arcs). The extracted responses from both analyses correspond to the oxygen reduction reactions that follow the Adler-Lane-Steele model. The stabilized symmetrical cells for respective 34 h and 17 h show an area-specific resistance (ASR) of (i) 0.22 Ωcm2 and 0.30 Ωcm2 (by CNLS) and (ii) 0.20 Ωcm2 and 0.26 Ωcm2 (by DRT). In addition, the ASR of the cell at T = 700 °C and T = 750 °C after being stabilized for 34 h is (iii) 0.71 Ωcm2 and 0.40 Ωcm2 (by CNLS) and (iv) 0.70 Ωcm2 and 0.44 Ωcm2 (by DRT), accordingly. Conversely, the cell's microstructure is not affected by the applied stabilization periods as observed by a scanning electron microscope. [Display omitted] • DRT analysis predominantly expresses P 1 , P 2 , P 3 and P 4 cathode sub-processes. • The 34 h stabilization period is sufficient to stabilize a 25-mm PCFC button cell. • ASR value of the S34 is lower than S17 according to DRT and CNLS analysis. • Shorter relaxation time means a faster kinetic reaction of electrochemical processes. [ABSTRACT FROM AUTHOR]