Search

OBJECTIVE: The purpose of this study was to assess the push-out bond strength of glass fiber posts to root dentin after cementation with glass ionomer (GICs) and resinmodified glass ionomer cements (RMGICs). MATERIAL AND METHODS: Fifty human maxillary canines were transversally sectioned at 15 mm from the apex. Canals were prepared with a step back technique until the application of a #55 K-file and filled. Post spaces were prepared and specimens were divided into five groups according to the cement used for post cementation: Luting & Lining Cement; Fuji II LC Improved; RelyX Luting; Ketac Cem; and Ionoseal. After cementation of the glass fiber posts, all roots were stored at 100% humidity until testing. For push-out test, 1-mm thick slices were produced. The push-out test was performed in a universal testing machine at a crosshead speed of 0.5 mm/minute and the values (MPa) were analyzed by Kolmogorov-Smirnov and Levene's tests and by two-way ANOVA and Tukey's post hoc test at a significance level of 5%. RESULTS: Fiber posts cemented using Luting & Lining Cement, Fuji II LC Improved, and Ketac Cem presented the highest bond strength to root dentin, followed by RelyX Luting. Ionoseal presented the lowest bond strength values (P>0.05). The post level did not influence the bond strength of fiber posts to root dentin (P=0.148). The major cause of failure was cohesive at the cement for all GICs and RMGICs. CONCLUSIONS: Except for Ionoseal, all cements provided satisfactory bond strength values.

Hypodontia is the congenital absence of one or more teeth and may affect permanent teeth. Several options are indicated to treat hypodontia, including the maintenance of primary teeth or space redistribution for restorative treatment with partial adhesive bridges, tooth transplantation, and implants. However, a multidisciplinary approach is the most important requirement for the ideal treatment of hypodontia. This paper describes a multidisciplinary treatment plan for congenitally missing permanent mandibular second premolars involving orthodontics, implantology and prosthodontic specialties.

Dental impression is an important step in the preparation of prostheses since it provides the reproduction of anatomic and surface details of teeth and adjacent structures. The objective of this study was to evaluate the linear dimensional alterations in gypsum dies obtained with different elastomeric materials, using a resin coping impression technique with individual shells. A master cast made of stainless steel with fixed prosthesis characteristics with two prepared abutment teeth was used to obtain the impressions. References points (A, B, C, D, E and F) were recorded on the occlusal and buccal surfaces of abutments to register the distances. The impressions were obtained using the following materials: polyether, mercaptan-polysulfide, addition silicone, and condensation silicone. The transfer impressions were made with custom trays and an irreversible hydrocolloid material and were poured with type IV gypsum. The distances between identified points in gypsum dies were measured using an optical microscope and the results were statistically analyzed by ANOVA (p < 0.05) and Tukey's test. The mean of the distances were registered as follows: addition silicone (AB = 13.6 µm, CD=15.0 µm, EF = 14.6 µm, GH=15.2 µm), mercaptan-polysulfide (AB = 36.0 µm, CD = 36.0 µm, EF = 39.6 µm, GH = 40.6 µm), polyether (AB = 35.2 µm, CD = 35.6 µm, EF = 39.4 µm, GH = 41.4 µm) and condensation silicone (AB = 69.2 µm, CD = 71.0 µm, EF = 80.6 µm, GH = 81.2 µm). All of the measurements found in gypsum dies were compared to those of a master cast. The results demonstrated that the addition silicone provides the best stability of the compounds tested, followed by polyether, polysulfide and condensation silicone. No statistical differences were obtained between polyether and mercaptan-polysulfide materials.

Microleakage can be related to margin misfit. Also, traditional microleakage techniques are time-consuming. This study evaluated the existence of correlation between in vitro margin fit and a new microleakage technique for complete crowns cemented with 3 different luting agents. Thirty human premolars were prepared for full-coverage crowns with a convergence angle of 6 degrees, chamfer margin of 1.2 mm circumferentially, and occlusal reduction of 1.5 mm. Ni-Cr cast crowns were cemented with either zinc phosphate (ZP) (S.S. White), resin-modified glass-ionomer (RMGI) (Rely X Luting Cement) or a resin-based luting agent (RC) (Enforce). Margin fit (seating discrepancy and margin gap) was evaluated according to criteria in the literature under microscope with 0.001 mm accuracy. After thermal cycling, crowns were longitudinally sectioned and microleakage scores at tooth-cement interface were obtained and recorded at ×100 magnification. Margin fit parameters were compared with the one-way ANOVA test and microleakage scores with Kruskal-Wallis and Dunn's tests (alpha=0.05). Correlation between margin fit and microleakage was analyzed with the Spearman's test (alpha=0.05). Seating discrepancy and marginal gap values ranged from 81.82 µm to 137.22 µm (p=0.117), and from 75.42 µm to 78.49 µm (p=0.940), respectively. Marginal microleakage scores were ZP=3.02, RMGI=0.35 and RC=0.12 (p0.05). Conclusion: Margin fit parameters and microleakage showed no strong correlations; cast crowns cemented with RMGI and RC had lower microleakage scores than ZP cement.

OBJECTIVE: The purpose of this study was to perform a radiographic follow-up evaluation after a 12-month healing period, following crown lengthening surgery. MATERIAL AND METHODS: Twenty-three periodontally healthy subjects (mean age 32.5 years) that required crown lengthening surgery in premolars were recruited. In a total of 30 premolars, full thickness flaps, osseous resection, and flap suturing were performed. The restorative margin was defined in the pre-surgical phase and maintained unaltered during the healing period, serving as a reference point. Standardized bitewing radiographs were taken before and after osseous reduction, and at 2, 3, 6, and 12-month healing periods. RESULTS: Intact lamina dura was observed at both mesial and distal alveolar crests only from the 3rd month. At 12-months, all alveolar crests presented lamina dura. The overall mean distance from the restorative margin to the alveolar crest achieved after osseous resection was 3.28±0.87 mm at mesial and 2.81±0.51 mm at distal sites. No significant radiographic changes in the bone crest were observed during a 12-month healing period. CONCLUSION: The findings of this study suggest that the radiographic proximal bone level observed on bitewing radiographs following crown lengthening surgery can be used as a reference to predict the future level of the healed alveolar crest.

Proper selection of the luting agent is fundamental to avoid failure due to lack of retention in post-retained crowns. The objective of this study was to investigate the tensile bond strength and failure mode of glass fiber posts luted with different cements. Glass fiber posts were luted in 40 mandibular premolars, divided into 4 groups (n = 10): Group 1 - resin-modified glass ionomer RelyX Luting; Group 2 - resin-modified glass ionomer Fuji Plus; Group 3 - resin cement RelyX ARC; Group 4 - resin cement Enforce. Specimens were assessed by tensile strength testing and light microscopy analysis for observation of failure mode. The tensile bond strength values of each group were compared by ANOVA and Tukey test. The significance level was set at 5%. The failure modes were described as percentages. The following tensile strength values were obtained: Group 1 - 247.6 N; Group 2 - 256.7 N; Group 3 - 502.1 N; Group 4 - 477.3 N. There was no statistically significant difference between Groups 1 and 2 or between Groups 3 and 4, yet the resin cements presented significantly higher tensile bond strength values than those presented by the glass ionomer cements. Group 1 displayed 70% of cohesive failures, whereas Groups 2, 3 and 4 exhibited 70% to 80% of adhesive failures at the dentin-cement interface. We concluded that resin cements and glass ionomer cements are able to provide clinically sufficient retention of glass fiber posts, and that glass ionomer cements may be especially indicated when the application of adhesive techniques is difficult.A seleção adequada do agente cimentante é essencial para evitar falhas por perda de retenção em coroas retidas por núcleos. O objetivo deste estudo foi investigar a resistência à tração e o tipo de falha de pinos de fibra de vidro cimentados com diferentes materiais. Cimentaram-se pinos de fibra de vidro em 40 pré-molares inferiores, divididos em 4 grupos (n = 10): Grupo 1 - ionômero de vidro modificado por resina RelyX Luting; Grupo 2 - ionômero de vidro modificado por resina Fuji Plus; Grupo 3 - cimento resinoso RelyX ARC; Grupo 4 - cimento resinoso Enforce. Avaliaram-se os espécimes por teste de resistência à tração e análise por microscopia óptica para observação do tipo de falha. Compararam-se os valores de resistência à tração de cada grupo por análise de variância e teste de Tukey, sendo que o nível de significância estabelecido foi de 5%. Descreveram-se os tipos de falha na forma de porcentagens. Os valores de resistência à tração obtidos foram: Grupo 1 - 247,6 N; Grupo 2 - 256,7 N; Grupo 3 - 502,1 N; Grupo 4 - 477,3 N. Não houve diferença estatisticamente significativa entre os Grupos 1 e 2 ou entre os Grupos 3 e 4, porém os cimentos resinosos apresentaram valores de resistência à tração significativamente maiores do que os apresentados pelos cimentos ionoméricos. O Grupo 1 exibiu 70% de falhas coesivas, enquanto os Grupos 2, 3 e 4 apresentaram 70% a 80% de falhas adesivas na interface dentina-cimento. Concluiu-se que os cimentos resinosos e ionoméricos são capazes de proporcionar retenção clinicamente suficiente de pinos de fibras de vidro, e que os cimentos ionoméricos podem ser indicados principalmente quando houver dificuldades de aplicar técnicas adesivas.

The aim of the work was to evaluate the influence of the temperature of investment healting on the tensile strength and Vickers hardness of CP Ti and Ti-6Al-4V alloy casting. Were obtained for the tensile strength test dumbbell rods that were invested in the Rematitan Plus investment and casting in the Discovery machine cast. Thirty specimens were obtained, fiftten to the CP Titanium and fifteen to the Ti-6Al-4V alloy, five samples to each an of the three temperatures of investment: 430ºC (control group), 480ºC and 530ºC. The tensile test was measured by means of a universal testing machine, MTS model 810, at a strain of 1.0 mm/min. After the tensile strenght test the specimens were secctioned, embedded and polished to hardness measurements, using a Vickers tester, Micromet 2100. The means values to tensile tests to the temperatures 430ºC, 480 and 530: CP Ti (486.1 - 501.16 - 498.14 -mean 495.30 MPa) and Ti-6Al-4V alloy (961.33 - 958.26 - 1005.80 - mean 975.13 MPa) while for the Vickers hardness the values were (198.06, 197.85, 202.58 - mean 199.50) and (352.95, 339.36, 344.76 - mean 345.69), respectively. The values were submitted to Analysis of Variance (ANOVA) and Tukey,s Test that indicate differences significant only between the materials, but not between the temperature, for both the materias. It was conclued that increase of the temperature of investment its not chance the tensile strength and the Vickers hardness of the CP Titanium and Ti-6Al-4V alloy.

A group of destructive changes occurring in jaws in patients with maxillary complete dentures and mandibular removable partial dentures (bilaterally) has been described in the literature as the combination syndrome. However, this condition is not clinically observed in all patients. The aim of this study was to establish the prevalence index on signs of combination syndrome and to verify whether these changes also occurred in patients rehabilitated with a mandibular removable partial denture (unilaterally). Sample was composed of 44 patients, completely edentulous in the maxilla. Thirty-two patients had a Kennedy Class I removable partial denture and 12 a Kennedy Class II. Three major alterations were observed in 20.5% of the studied population. Nevertheless, these changes were present only in 25% of patients with Kennedy Class I removable partial denture. Based on the findings of this study, it can be concluded that patients with Kennedy Class II removable partial denture do not have similar signs that lead to the combination syndrome's condition.

OBJECTIVE: This study evaluated the fracture strengths of endodontically treated teeth restored with prefabricated posts with different post lengths. MATERIAL AND METHODS: Thirty freshly extracted canines were endodontically treated. They were randomly divided into groups of 10 teeth and prepared according to 3 experimental protocols, as follows; Group 1/3 PP: teeth restored with prefabricated post and composite resin core (Z250) with post length of 5.0mm; Group 1/2 PP and Group 2/3 PP: teeth restored with prefabricated post and composite resin core (Z250) with different combinations of post length of 7.5mm and 10mm, respectively. All teeth were restored with full metal crowns. The fracture resistance (N) was measured in a universal testing machine (crosshead speed 0.5mm/min) at 45 degrees to the tooth long axis until failure. Data were analyzed by one-way analysis of variance (alpha=.05). RESULTS: The one-way analysis of variance demonstrated no significant difference among the different post lengths (P>.05) (Groups 1/3 PP = 405.4 N, 1/2 PP = 395.6 N, 2/3 PP = 393.8 N). Failures occurred mainly due to core fracture. CONCLUSIONS: The results of this study showed that an increased post length in teeth restored with prefabricated posts did not significantly increase the fracture resistance of endodontically treated teeth.

Aim: This study compared the fracture resistance of endodontically treated teeth restored with posts and cores systems with different post lengths. Methods: Sixty extracted intact canines were randomly divided in 6 groups of 10 teeth each, as follows: groups 1, 2 and 3 were restored with custom cast post-and-core, and groups 4, 5 and 6 were restored with prefabricated post and composite resin core, with different post lengths (5.0, 7.5 and 10 mm, respectively). A compressive load was applied at a 45-degree angle to the long axis until failure occurred. Results: Two-way analysis of variance (á=0.05) showed statistically significant difference between the groups (p

Aim: This study compared the tensile strength of endodontically treated teeth restored with different posts and cores with different post lengths. Methods: Sixty extracted intact canines were randomly divided into 6 groups. Groups CP1, CP2 and CP3 were restored with custom cast postand-core and groups PF1, PF2 and PF3 were restored with prefabricated post and composite resin core, with different combinations of post length of 5,0 mm, 7.5 mm and 10 mm, respectively (n = 10). All teeth were restored with a total metal crown. A tensile loading was applied at a 180- degree angle to the long axis until failure. Results: The 2-way analysis of variance (á=0.05) showed statistically significant difference (p

Aim: This study compared the resistance to fracture of endodontically treated teeth restored with different intraradicular posts with different lengths and full coverage metallic crowns. Methods: Sixty extracted human canine teeth were randomly divided into 6 groups. Groups CP5, CP75 and CP10 were restored using custom cast post and core (CP) and groups PF5, PF75 and PF10 were restored with provisional pre-fabricated tin post (PF) and composite resin core at 5 mm, 7.5 mm and 10 mm of intraradicular length, respectively. The specimens were submitted to dynamic cyclic loading and those that resisted to this load were submitted to load compression using a universal testing machine. Compressive load was applied at a 45-degree angle to the long axis of the tooth until failure. Results: Kruskal-Wallis one-way analysis of variance by ranks showed statistically significant differences among the groups (p

OBJECTIVE: This study investigated the compressive fracture strength and failure pattern in premolars submitted to endodontic treatment and internal bleaching with 37% carbamide peroxide for 21 days, with application of different restorative procedures. MATERIAL AND METHODS: Six groups were employed (n = 10): 1) non-bleached teeth and pulp chamber sealed with IRM; 2) bleached teeth and pulp chamber sealed with IRM; 3) bleached teeth and pulp chamber filled with light cured composite resin; 4) bleached teeth, root canals prepared at 10mm, filling of the root canal and pulp chamber with IRM; 5) bleached teeth, root canals prepared at 10mm, luting of prefabricated metallic post with zinc phosphate and pulp chamber sealed with composite resin; 6) bleached teeth, root canals prepared at 10mm, luting of glass fiber post with resin cement and pulp chamber sealed with composite resin. After 24-hour storage in distilled water, the specimens were submitted to compressive fracture strength testing in a universal testing machine. RESULTS: The following values were found: Group 1 - 56.23kgf; Group 2 - 48.96kgf; Group 3 - 53.99kgf; Group 4 - 45.72kgf; Group 5 - 54.22kgf; Group 6 - 60.12kgf. The analysis of variance did not reveal statistically significant difference between groups (pOBJETIVO: O objetivo do estudo foi investigar a resistência à fratura sob compressão e padrão de falha de pré-molares tratados endodonticamente e clareados internamente por 21 dias com peróxido de carbamida a 37%, aplicando-se diferentes procedimentos restauradores. MATERIAL E MÉTODOS: O objetivo deste estudo foi investigar a resistência à fratura sob compressão e padrão de falha de pré-molares unirradiculares tratados endodonticamente e clareados internamente com peróxido de carbamida a 37%. Foram constituídos 6 grupos (n = 10): 1) dentes sem clareamento e câmara pulpar vedada com IRM; 2) dentes clareados e câmara pulpar vedada com IRM; 3) dentes clareados e câmara pulpar preenchida com resina composta fotopolimerizável; 4) dentes clareados, condutos preparados com 10mm, e preenchimento do conduto e câmara pulpar com IRM; 5) dentes clareados, condutos preparados com 10mm, cimentação de pino metálico pré-fabricado com fosfato de zinco e câmara pulpar vedada com resina composta; 6) dentes clareados, condutos preparados com 10mm, cimentação de pino de fibra de vidro com cimento resinoso e câmara pulpar vedada com resina composta. Após 24 horas de armazenamento em água destilada, os espécimes foram submetidos ao teste de resistência à fratura sob compressão em máquina de ensaios universal. RESULTADOS: Os seguintes valores foram encontrados: grupo 1 - 56,23kgf; grupo 2 - 48,96kgf; grupo 3 - 53,99kgf; grupo 4 - 45,72kgf; grupo 5 - 54,22kgf; grupo 6 - 60,12kgf. A Análise de Variância não mostrou diferença estatisticamente significante entre os grupos (p < .05), sugerindo que o clareamento interno com peróxido de carbamida a 37% não enfraqueceu os tecidos dentais. O maior número de fraturas desfavoráveis foi encontrado nos grupos 2 (50%), 4 (40%), e 5 (30%). O grupo 6 exibiu o padrão de falhas mais favorável. CONCLUSÃO: Os resultados sugerem que o clareamento interno com peróxido de carbamida a 37% não causou enfraquecimento importante dos dentes. Entre os dentes clareados, aqueles com restaurações temporárias de IRM ou com pinos metálicos mostraram o padrão mais desfavorável de fratura, enquanto o padrão de fratura mais favorável ocorreu em dentes restaurados com resina composta e pinos de fibras de vidro.

The aim of this study was to measure marginal fit at cylinder-abutment interface, before and after overcasting procedure. A hexagonal implant was fixed to a stainless steel base and a Estheticone-like abutment used during all the experiment. Before casting procedure, gold (Group I) and Ni-Cr-Be (Group II) premachined cylinders were tightened to the abutment with gold and titanium screws (in both groups), with 10Ncm and 20Ncm torque values for the same screw type. Vertical measures were taken at the light microscope (Mitutoyo 5050, Tokyo, Japan) three times in six different parts along the abutment-cylinder interface for each torque value. Cylinders were overcast with Ag-Pd (Group I) or Ni-Cr-Be (Group II) alloy. After casting, the same measures and torque values were repeated. Intragroup differences (10 or 20Ncm torque values, before and after casting) and intergroup differences (10 and 20Ncm torque values, before or after casting) were analyzed by the Paired t Test; (pO objetivo deste estudo foi medir a adaptação marginal na interface intermediário-cilindro, antes e após a sobrefundição. Um implante do tipo hexágono externo afixado numa base de aço inoxidável e um intermediário do tipo Estheticone foram usados durante todo o experimento. Antes das fundições, cilindros pré-usinados de ouro (Grupo I) e de Ni-Cr-Be (Grupo II) foram aparafusados ao intermediário com parafusos de ouro e titânio em ambos os grupos, com torques de 10Ncm e 20Ncm para o mesmo tipo de parafuso. As medidas verticais foram feitas num microscópio óptico (Mitutoyo 5050, Tóquio, Japão) três vezes em seis locais diferentes ao longo da interface intermediário-cilindro para cada valor de torque. Os cilindros foram encerados e fundidos tanto em liga de Ag-Pd (Grupo I) ou liga de Ni-Cr-Be (Grupo II). Após as fundições, as mesmas medidas e os mesmos valores de torque foram repetidos. As diferenças intra-grupo (torques de 10 ou 20Ncm, antes e após as fundições) e as diferenças inter-grupos (torques de 10 e 20Ncm, antes ou após as fundições) foram analisadas pelo teste t pareado (p

OBJECTIVES: The aim of this study was to evaluate the influence of remaining coronal tooth structure on endodontically treated teeth restored with prefabricated posts and two different composites for core build-up: dual-cured resin (Enforce Core) and light-cured resin (Z-250). METHODS: Fourty freshly extracted canines were endodontically treated and divided into four groups: Group I - teeth with 3mm remaining coronal structure, restored with Enforce Core; Group II - teeth with 3mm remaining coronal structure, restored with Z-250; Group III - teeth with no remaining coronal structure, restored with Enforce; Group IV - teeth with no remaining coronal structure, restored with Z-250. After restoration, the teeth were embedded in acrylic resin and the fracture resistance was measured on a universal testing machine at 45 degrees to the long axis of the tooth until failure. RESULTS: Data were analyzed by two-way analysis of variance, which showed significant differences between groups (p=0.00). The Tukey test did not show significant differences between specimens with and without remaining coronal structure. Conversely, significant difference was observed between groups with different core build-up. The highest values of fracture resistance were found in the group restored with light-cured resin. SIGNIFICANCE: The remaining coronal tooth structure did not influence the resistance of endodontically treated teeth; however, the change of core build-up was able to modify this resistence.O objetivo desta pesquisa foi avaliar a influência do remanescente dentário coronal de dentes tratados endodonticamente, restaurados com pinos pré-fabricados e duas resinas como núcleos de preenchimento, uma de presa dual (Enforce Core) e outra fotopolimerizável (Z-250). Foram utilizados 40 caninos superiores humanos extraídos, divididos em quatro grupos de 10 espécimes: Grupo l - com remanescente dentário coronal de 3mm e restaurados com Enforce Core; Grupo ll - com remanescente dentário coronal de 3mm e restaurado com Z-250; Grupo III - sem remanescente dentário coronal e restaurado com Enforce Core; Grupo IV - sem remanescente dentário coronal e restaurado com Z-250. Após restaurados, os dentes foram levados a uma Máquina de Ensaio Universal e submetidos a uma força de compressão à 45º até que ocorresse fratura da restauração. A análise dos resultados (ANOVA, p>0,05) mostrou não haver diferença estatisticamente significativa entre os dentes com e sem remanescente dentário coronal. Com relação ao material utilizado para o preenchimento coronário, constatou-se diferença significativa, sendo que os valores mais elevados de resistência à fratura foram encontrados no grupo restaurado com a resina fotopolimerizável.

Context: The complexities of the oral environment, the dentin substrate, and the different bond and composite resin systems represent a challenge to the maintenance of reasonable bond between the composite resin and the tooth structure. Aims: To evaluate the effect of the adhesive system on bond strength between silorane-based composite resin and dentin. Materials and Methods: Fourteen human molars extracted were selected and vertically cut into 3 dentin fragments, randomly divided among the experimental groups and restored with Z250 and P90 composite resin using different adhesive protocols (Adper Single Bond 2, Silorano primer, Adper SE Plus, and Scotchbond Multiuse). Two composite resin cylinders were built up on each dentin surface (n = 10) and subjected to a micro-shear bond strength test. Statistical Analysis Used: Kruskal–Wallis one-way analysis of variance and Tukey test (P = 0.05). Results: According to the results, Kruskal–Wallis test evidenced at least one statistical significant difference (P = 0.001). The Tukey test showed statistically significant differences among the group (P < 0.05). Group PSM8 (P90 + SM) showed statically significant higher results when compared with groups PSP4 (P90 + SP), PSB2 (P90 + SB), and ZSE5 (Z250 + SE). Conclusion: The results evidenced that the monomer of the adhesive system has an effect on bond strength between the composite resin and dentin. [ABSTRACT FROM AUTHOR]

The aim of this study was to evaluate the tensile resistance of mineralized and demineralized bones. Twelve mice were used. Specimens were collected and divided into groups 1 and 2, mineralized and demineralized calvarial bone, and groups 3 and 4, mineralized and demineralized femoral bone. There was not a statistically significant difference (analysis of variance) between the regions; however, when comparing the demineralized and mineralized groups, a statistically significant difference (Student test) for the mineralized group was noticed. [ABSTRACT FROM AUTHOR]

Aim: This study compared the resistance to fracture of endodontically treated teeth restored with different intraradicular posts with different lengths and full coverage metallic crowns. Methods: Sixty extracted human canine teeth were randomly divided into 6 groups. Groups CP5, CP75 and CP10 were restored using custom cast post and core (CP) and groups PF5, PF75 and PF10 were restored with provisional pre-fabricated tin post (PF) and composite resin core at 5 mm, 7.5 mm and 10 mm of intraradicular length, respectively. The specimens were submitted to dynamic cyclic loading and those that resisted to this load were submitted to load compression using a universal testing machine. Compressive load was applied at a 45-degree angle to the long axis of the tooth until failure. Results: Kruskal-Wallis one-way analysis of variance by ranks showed statistically significant differences among the groups (p<0.0001). However, when the means were compared using the Tukey's test, significant differences were noted between groups CP5 and CP10 and between groups CP10 and PF5. All groups presented root fractures and post displacements during mechanical cycling. All teeth in groups CP5 and PF5 failed the dynamic cycling test. Conclusions: This study showed that increasing intraradicular post length also increases resistance to fracture of endodontically treated teeth. On the other hand, most endodontically treated teeth restored with pre-fabricated tin posts (provisional posts) failed in the dynamic cycling test. [ABSTRACT FROM AUTHOR]

Statement of problem: Root fracture is one of the most serious complications following restoration of endodontically treated teeth. Purpose: The purpose of this study was to compare the fracture strengths of endodontically treated teeth using posts and cores and variable quantities of coronal dentin located apical to core foundations with corresponding ferrule designs incorporated into cast restorations. Material and methods: Fifty freshly extracted canines were endodontically treated. The teeth were randomly divided into groups of 10 and prepared according to 5 experimental protocols. Control group: teeth with custom cast post and core; 0-mm group: teeth without coronal structure (no ferrule); 1-mm, 2-mm, and 3-mm groups: teeth with 1 mm, 2 mm, and 3 mm of remaining coronal tooth structure (1-, 2-, and 3-mm ferrule), respectively. All specimens in 0-mm through 3-mm (noncontrol) groups were restored with a prefabricated post (Screw-Post) and composite resin (Z100) core located superior to the different tooth structure heights. All teeth were restored with complete metal crowns. The fracture resistance (N) was measured in a universal testing machine at 45 degrees to the long axis of the tooth until failure. Data were analyzed by 1-way analysis of variance and Tukey test (α=.05). Results: Significant differences (P<.001) were found among the mean fracture forces of the test groups (control group: 818.2 N; 0-mm, 1-mm, 2-mm, and 3-mm groups: 561.0 N, 627.6 N, 745.3 N, and 907.1 N, respectively). When the mode of failure was evaluated, all failures in the control group occurred due to root fracture, and all failures in the 0-mm group occurred due to core fracture. The majority of failures in the other groups occurred due to crown cementation failure. Conclusion: The results of this study showed that an increased amount of coronal dentin significantly increases the fracture resistance of endodontically treated teeth. [Copyright &y& Elsevier]

Purpose: To evaluate biologic and prosthetic outcomes of implant-supported mandibular full-arch fixed prostheses treated with the All-on-4 treatment concept after 7 years., Materials and Methods: Patients were selected to receive full-arch fixed immediate prostheses supported by four implants up to 72 hours after surgery. The following biologic aspects were evaluated: Plaque Index (PI) and Bleeding Index (BI), implant stability by resonance frequency, and marginal bone loss (MBL) measured with the aid of periapical radiographs. The prosthetic complications evaluated were related to screw loosening, framework or acrylic teeth fractures, or fractures of implants. The means of implant stability and MBL were subjected to analysis of variance and the Tukey test (P < .05). For PI and BI, the Friedmann test was used (P < .05)., Results: Sixteen patients (12 women and 4 men; mean age: 59.1 years) received 64 implants, and in all patients, two implants were positioned axially at the incisor region and two distally tilted implants at the region of the second premolars or molars. Patients were evaluated immediately after surgery and at 1, 2, and 7 years. Fifteen patients attended the recall after 2 years; one patient could not attend the scheduled follow-up visit and was excluded from the sample. In the 7-year evaluation, the sample size decreased to 12 patients; one could not attend because of a severe disease, and two were deceased. The cumulative implant survival rate was 100%. There was a significant (P < .0162) decrease in PI at the 1- and 7-year evaluations (71.87% and 47.92%, respectively), while the BI was the same at 1 and 7 years (43.75%). There was no statistical difference in MBL (P = .12) and implant stability (P = .48) between axial and tilted implants (P = .48). The survival rate of prostheses was 100%. The following technical complications were observed: tooth fracture occurred in one patient (6.25%); loosening of prosthetic screws and abutments were observed in three patients (18.75%); after 5 years, three patients (18.75%) had changed the denture acrylic teeth because of the replacement of the removable total maxillary prostheses with fixed implant prostheses., Conclusion: For the 12 patients who attended the recall after 7 years, implant loss was not found, the implant stability was high, MBL was low, and prosthetic complications were easily solved. Thus, it can be concluded that rehabilitation with implant-supported mandibular full-arch fixed prostheses with four implants has proved to be a treatment with a high survival rate.