Search

A novel quality assurance process for electroanatomical mapping (EAM)-to-radiotherapy planning imaging (RTPI) target transport was assessed within the multi-center multi-platform framework of the RAdiosurgery for VENtricular TAchycardia (RAVENTA) trial. A stand-alone software (CARDIO-RT) was developed to enable platform independent registration of EAM and RTPI of the left ventricle (LV), based on pre-generated radiotherapy contours (RTC). LV-RTC were automatically segmented into the American-Heart-Association 17-segment-model and a manual 3D-3D method based on EAM 3D-geometry data and a semi-automated 2D-3D method based on EAM screenshot projections were developed. The quality of substrate transfer was evaluated in five clinical cases and the structural analyses showed substantial differences between manual target transfer and target transport using CARDIO-RT.

In this paper, in order to reduce the probability of the radar waveform intercepted by the passive detection system, the time-bandwidth product of the radar waveform is increased, and the detection probability of the radar waveform to the target is improved. This paper tackles the holographic RF stealth radar and proposes a joint coding waveform based on the linear frequency modulation (LFM) waveform. Joint coding uses complementary codes to perform phase-coding, and combines the codewords optimized by genetic algorithm in order to perform discrete frequency-coding waveform. The joint coding waveform model is theoretically analyzed, and the ambiguity function, pulse compression and target detection probability of the joint coding waveform are obtained by numerical simulation. In addition, the complexity of the algorithm and the low probability of intercept (LPI) characteristic of the joint coding waveform are analyzed. The results show that the joint coding waveform has an approximate “pushpin” ambiguity function, ultra-low sidelobe characteristics, better RF stealth and target detection performance. Finally, it has good application prospects in the current battlefield environment.

The micromechanical properties of soft tissue can be used as markers for the physiological state and function of the tissue. Deep understanding of the micromechanics of soft tissue, such as the oesophagus, is of great significance to the design of artificial oesophagi, endoscope materials and coatings for medical devices. Here, the micromechanical properties of oesophageal mucosa were studied under different loading rates, deflections, and dwell time by using atomic force microscopy. The micromechanical properties of soft tissue included elastic modulus, plasticity and adhesion force. Results showed that the micromechanical properties changed with increasing loading rate, deflection and dwell time. The micromechanical properties of oesophageal mucosa were related to time-dependent behaviours, such as contact stress, energy transformation, and strain gradient plasticity. Furthermore, the heterogeneity of oesophageal mucosa affected the micromechanical properties. The force mapping mode was a reliable and effective means to study the micromechanical properties of soft tissue. The results can provide a basis and technical support for the diagnosis of oesophageal diseases from a microscale as well as a material design perspective.

Purpose: The friction characteristics at the interface between prosthetic socket and liner have an important influence on the walking function and wearing comfort of amputees. The frictional behavior at the prosthetic socket/liner interface can provide theoretical guidance for the design and selection of prosthetic materials. So it is of great significance to study the friction behavior at prosthetic socket/liner interface. Methods: The surface roughnesses of the prosthetic socket and liner materials were measured by a laser confocal microscope. The frictional behavior at the prosthetic socket/liner interface was studied on a UMT TriboLab Tribometer by simulating the reciprocating sliding contact mode. An infrared camera was used to take thermal images and then calculated the temperature increase at the socket/liner interface. Results: The coefficient of friction of the silicon rubber fabric are significantly smaller than that of the foam liner materials. The frictional energy dissipation at the liner/acrylic socket interface is the smallest, while it is greater for 3D-printed socket materials. Meanwhile, the temperature increase has a positive correlation to the coefficient of friction and frictional energy dissipation. Conclusions: The three kinds of 3D-printed materials with high surface roughness have higher interface coefficient of friction and energy dissipation than acrylic material. The stiffness and energy consumption play an important role in the interface friction characteristics of the prosthetic liner materials. The appropriate coefficient of friction at the surface between prosthetic socket and liner is essential. A type of the reinforcement fiber has influence on the friction behavior of the 3D-printed reinforced nylon. [ABSTRACT FROM AUTHOR]