Search

In the recent times, pseudocapacitive electrode materials have received great attention due to their considerable capability in storing ions at relatively fast charging rates. Among various candidates, niobium (V) pentoxide (Nb 2 O 5 ) has gained much attraction for lithium-ion batteries (LIBs) due to its insertion/extraction reaction with Li, safe redox potential, and considerably good capacity (about 200 mAhg −1 ). Nevertheless, low conductivity of Nb 2 O 5 has so far prevented its use as a viable electrode material for LIBs. In this study, we have successfully coated silver (Ag) nanoparticles (NPs) on the surface of one-dimensional orthorhombic Nb 2 O 5 fiber (1D T-Nb 2 O 5 ) using simple electrospinning processing. Ag NPs coated Nb 2 O 5 fibers (Ag-1D T-Nb 2 O 5 ) provided faster electron pathways, resulting in much improved capacity at a given current density with superior rate capabilities compared with pristine 1D T-Nb 2 O 5 . In addition, 1D T-Nb 2 O 5 was more suitable for coating Ag NPs compared with T-Nb 2 O 5 NPs, where its structural integrity was maintained even after cycling. As a result, effective coating of conductive Ag NPs on the 1D T-Nb 2 O 5 resulted in excellent cycle retention characteristics (179.7 mAhg −1 after 500 cycles at 500 mA g −1 ) as well as superior rate capabilities (103.6 mAhg −1 at a current density of 5000 mA g −1 ). [ABSTRACT FROM AUTHOR]

Structural and electronic modification of titanium oxide (TiO 2 ) nanomaterials induced by the co-introduction of fully disordered glass phase and oxygen vacancies can lead to remarkable advances in the electrode performance in emerging energy storage systems. We report on the effective co-creation of fully amorphous nanofibers (NFs) composed of black TiO 2-x and conductive carbons throughout the NF structure, and evaluate the materials as potential anodes in sodium-ion batteries. The black TiO 2-x nanofiber is successfully fabricated by electrospinning a precursor solution followed by a two-step sequential thermal treatment in an air and reducing atmosphere. The NF electrode could deliver approximately two-fold higher 2nd discharge capacity and an excellent kinetic performance even under high rates compared to that delivered by anatase-structured white TiO 2 NFs used as reference, because of (i) an inherent free volume in the glass phase corresponding to the enlarged Na + sites, (ii) increased electrical conductivity (low bandgap) resulting from the presence of Ti 3+ , (iii) introduction of conductive carbon agents around the TiO 2-x domain, and (iv) one-dimensional NF feature allowing numerous Na + reaction sites at the electrochemical interface. We also elucidate the morphological and structural changes in the nanofibers after discharge and charge by ex-situ characterizations. [ABSTRACT FROM AUTHOR]

Facile synthesis of rationally designed structures is critical to realize a high performance electrode for lithium-ion batteries (LIBs). Among different candidates, tin(IV) oxide (SnO 2 ) is one of the most actively researched electrode materials due to its high theoretical capacity (1493 mAh g −1 ), abundance, inexpensive costs, and environmental friendliness. However, severe capacity decay from the volume expansion and low conductivity of SnO 2 have hampered its use as a feasible electrode for LIBs. Rationally designed SnO 2 -based nanostructures with conductive materials can be an ideal solution to resolve such limitations. In this work, we have successfully fabricated porous SnO 2 -CuO composite nanotubes (SnO 2 -CuO p-NTs) by electrospinning and subsequent calcination step. The porous nanotubular structure is expected to mitigate the volume expansion of SnO 2 , while the as-formed Cu from CuO upon lithiation allows faster electron transport by improving the low conductivity of SnO 2 . With a synergistic effect of both Sn and Cu-based oxides, SnO 2 -CuO p-NTs deliver stable cycling performance (91.3% of capacity retention, ∼538 mAh g −1 ) even after 350 cycles at a current density of 500 mA g −1 , along with enhanced rate capabilities compared with SnO 2 . [ABSTRACT FROM AUTHOR]

Careful modulation of surficial and interfacial properties of electrode materials is a critical factor for determining overall electrochemical characteristics. Recent studies have indicated that metal oxide nanocoating layer (such as titanium (IV) oxide (TiO 2 )) on metal oxide anodes (such as tin (IV) oxide (SnO 2 )) exhibited superior electrochemical properties, but fundamental research on the effect and role of TiO 2 layer thickness has been limited. Here we have successfully conducted in-depth study on how the thickness of TiO 2 overlayer on SnO 2 can have significant influence in the overall parameters of electrochemistry. It is revealed that TiO 2 overlayer with 12 nm shows good cycle retention (75.8%) even after 80 cycles and retains capacity of 438.3 mAh g −1 even at high current density (5000 mA g −1 ). Surprisingly, it was further discovered that TiO 2 layer not only alleviates the volume expansion but also helps to facilitate Li ion transport compared with SnO 2 . The improvements in both ionic and electrical conductivity of TiO 2 layer are main factors in better cycle retention and rate capabilities. Finally, in situ transmission electron microscopy analysis was adopted to observe the growth dynamics of solid electrolyte interphase layer on TiO 2 @SnO 2 , which demonstrates that TiO 2 overlayer results in homogeneous and thinner interphase layer compared with SnO 2 NTs. [ABSTRACT FROM AUTHOR]

Colorless polyimide (CPI) is a promising material for flexible substrates because of its excellent mechanical hardness, chemical durability, thermal stability, and high optical transmittance. In particular, its superior durability under heating and mechanical forces compared with other polymeric materials makes polyimide compatible for industrial applications. Thus, it has been actively investigated for use in preparing flexible and transparent substrates for optical devices. Nevertheless, there is little research on the direct pattering of CPI to form structures with various optical functions. In this research, a simple and cost-effective process involving the patterning of optically functional structures and imidization via thermal nanoimprint lithography (NIL) was developed. CPI films patterned with structures such as nanoscale and microscale cones were fabricated by thermal NIL, and their optical functions, including their anti-reflection and high scattering properties, were demonstrated by UV–vis analysis. Moreover, the patterned CPI film has an excellent thermal stability and a mechanical hardness up to 1.12 GPa; this value was nearly maintained even at 400 °C. Therefore, nano- to microscale optical patterns of CPI were successfully formed, and these structures are stable towards mechanical damage and high temperatures. [ABSTRACT FROM AUTHOR]

Hydrous ruthenium oxide (RuO 2) has been considered a potential electrode for supercapacitors. However, RuO 2 is not easy to be hydrous, which impedes advancement in RuO 2 -based supercapacitors. Here, strontium cation (Sr2+) – with a lower oxidation state than Ru4+ – doping effects on improving the capability of RuO 2 to be hydrous are reported. The Sr2+ doping in the RuO 2 was simply possible using electrospinning and subsequent calcination, affecting hydrous properties and promoting miniaturization of nanograins in one-dimensional (1D) nanofibers. The compositions of hydrous Sr2+-doped RuO 2 (H-Sr x Ru 1−x O 2−x) nanofibers were optimized considering correlations between synthesis temperature and degree of hydration. It was found that the H-Sr 0.2 Ru 0.8 O 1.8 nanofibers synthesized at 400 °C were hydrous compared with the pristine RuO 2 and H-Sr 0.1 Ru 0.9 O 1.9 nanofibers. The H-Sr 0.2 Ru 0.8 O 1.8 nanofibers (400) could possess the smallest nanocrystallites, increasing electrochemically active surface area and satisfying specific capacitance of 612.6 A/g at a scan rate of 50 mV s–1. • A Sr2+-doped RuO 2 nanofibers were successfully fabricated by electrospinning and calcination. • Sr2+ doping enabled RuO 2 nanofibers to be hydrous and to possess miniaturized nanograins. • Sr2+ doping in RuO 2 was optimized for annealing temperature and composition. • The highly hydrous Sr 0.2 Ru 1.8 O 1.8 nanofibers boost the capacitance performance. [ABSTRACT FROM AUTHOR]

• The morph-genetic method was innovatively used to fabricate the ABH actuator. • The ABH actuator exhibits promising comprehensive performance. • The assembled biomimetic actuators show excellent synergistic performance. • The biomimetic actuator shows potential for a variety of applications. Stimuli-responsive hydrogels are most promising for the fabrication of autonomous bio-mimetic soft actuators. However, their weak actuation forces and isotropic volume change hinder their practical utilization as versatile actuators, owing to their fragility. Herein, we used the morph-genetic method to fabricate anisotropic bamboo/poly(N-isopropylacrylamide) hydrogel (ABH) complex for use as soft actuator. First of all, the bamboo fiber structure provides an anisotropic framework for the ABH actuator to achieve precise deformational programmability. Secondly, benefiting from the ultra-high directional strength (110 MPa) of bamboo, ABH actuator exhibits sufficiently robust mechanical property, which generates a powerful actuating force. Lastly, owing to the regulation of bamboo sheet and PNIPAM hydrogel, the ABH actuator not only achieves ultra-fast response speed (825°/s of the bending speed), but also has excellent synergetic performance. We demonstrate several bio-mimetic actuating devices based on ABH actuator, inspired by the intricate motions of natural organisms, to highlight how the specific materials properties and their synergy can be systematically exploited for the rational design of soft actuators. Henceforth, it is anticipated that the development of hydrogel actuators could continue to benefit from the use of various naturally-anisotropic materials, such as shape-memory polymers or liquid crystals, for the preparation of further advanced hydrogel actuators by the morph-genetic method. [ABSTRACT FROM AUTHOR]

Ultra-stable pseudocapacitive electrodes for lithium-ion batteries (LIBs) are increasing in demand as highly sustainable energy storage system with excellent charge transport is important. The establishment of facile, controllable, and scalable synthesis of pseudocapacitive electrode materials is an attractive solution to realize such objectives. Here, we have successfully fabricated mesoporous orthorhombic Nb 2 O 5 nanofibers (m-T-Nb 2 O 5 NFs) by simple single-spinneret electrospinning followed by calcination at 600 °C. As-formed m-T-Nb 2 O 5 NFs exhibit high surface area (23.7 m 2 g −1 ) and a number of mesopores in the vacant sites where organic polymer was once decomposed. Such rationally designed m-T-Nb 2 O 5 -NFs allow facile Li ion and electron transport, with pseudocapacitive behavior. Arising from the high surface area coupled with mesopores in-between the Nb 2 O 5 nanograins, it exhibits ultra-long cycle retention (a capacity of ∼160 mAh g −1 at 500 mA g −1 after 2000 cycles and ∼88 mAh g −1 at 3000 mA g −1 after 5000 cycles) and higher rate capability (∼70 mAh g −1 at 5000 mA g −1 ). Such cycle retention characteristics of m-T-Nb 2 O 5 -NFs are at least 100-fold slower capacity decay compared with previously reported one-dimensional (1D) Nb 2 O 5 nanostructures and even superior or comparable to recently reported Nb 2 O 5 -graphene composite materials. [ABSTRACT FROM AUTHOR]

Functionalization of catalytic nanoparticles (NPs) on semiconductor metal oxide (SMO) sensing layer is an indispensable process to obtain improved sensitivity and selectivity for high performance chemical sensors. It is a critical challenge to achieve homogeneous distribution of nanoscale catalysts on SMO in consideration that gas sensing characteristics of SMO-based sensing layer are significantly influenced by the size and distribution of catalysts. Here, we propose a highly effective functionalization method to achieve well-distributed catalytic NPs onto one dimensional (1D) SMO nanofibers (NFs) using protein cage templates: apoferrtin. By simply replacing precursor in the apoferritin assisted method, not only precious catalyst such as Pt but also non-precious catalysts such as La and Cu were successfully synthesized in nanoscale ( i.e. , 3–5 nm). Furthermore, the apoferritin-encapsulated catalysts exhibited high dispersion property due to repulsive force between protein shells. For this reason, catalytic NPs were homogeneously decorated on ZnO NFs after electrospinning followed by calcination. Catalytic Pt NPs and Cu NPs functionalized ZnO NFs exhibited approximately 6.38-fold (R air /R gas = 13.07) and 2.95-fold (R air /R gas = 6.04) improved acetone response compared with the response (R air /R gas = 2.05) of pristine ZnO NFs. In the case of La NPs functionalized ZnO NFs, 9.31-fold improved nitrogen monoxide response (R air /R gas = 10.06) was achieved compared with the response of pristine ZnO NFs. The four catalyst-ZnO composite NFs successfully distinguished simulated breath components such as acetone, toluene, nitrogen monoxide, carbon monoxide, and ammonia with well-classified patterns by principal component analysis (PCA). This work demonstrated a robustness of synthetic and functionalization method using bio-inspired protein templates combined with electrospinning technique and a promising potential of using non-precious catalysts to establish diverse sensing material libraries that can be applicable to breath pattern recognition for diagnosis of diseases. [ABSTRACT FROM AUTHOR]

In this work, a novel catalytic synthesis and functionalization method using apoferritin is used to fabricate RuO 2 nanoparticles (NPs) loaded WO 3 nanofibers (NFs) for potential diagnosis of diabetes. Catalytic ruthenium (Ru) NPs with very small average diameters of 1.8 ± 0.9 nm were synthesized using apoferritin which is a hollow protein cage, and were easily functionalized on WO 3 NFs by introducing electrospinning solution with W precursor and polyvinylpyrrolidone (PVP). As-spun Ru NPs-loaded W precursor/PVP composite NFs were calcined at 600 °C for 1 h in air atmosphere to achieve RuO 2 -functionalized WO 3 NFs. The small size and uniform distribution of catalytic RuO 2 NPs were well maintained due to hollow nature of apoferritin cages after calcination. The chemo-resistive sensors using RuO 2 -functionalized WO 3 NFs showed significantly enhanced acetone (CH 3 COCH 3 ) sensing response (R air /R gas = 78.61–5 ppm), which was 7.4 times higher than the response (R air /R gas = 10.61–5 ppm) of pristine WO 3 NFs at highly humid atmosphere (95% RH). In addition, the RuO 2 -functionalized WO 3 NFs showed outstanding selectivity toward acetone gas in comparison with other gases such as hydrogen sulfide (H 2 S), toluene (C 6 H 5 CH 3 ), ethanol (C 2 H 5 OH), pentane (C 5 H 12 ), ammonia (NH 3 ), hydrogen (H 2 ), and water vapor (H 2 O) at 5 ppm. These results represent potential feasibility for the detection of acetone in exhaled breath for diagnosis of diabetes. [ABSTRACT FROM AUTHOR]

Lightweight and ultrathin materials with superior electromagnetic interference (EMI) shielding performance are highly desirable for next-generation electronic devices. Herein, we fabricate a lightweight, thin, and flexible composite film, composed of Ti 3 C 2 T x MXene and nanoparticles of Galinstan liquid metal, by simple vacuum-assisted filtration as a promising candidate for EMI shielding. The resultant composite film with highly conductive liquid metal between the MXene nano sheets exhibits enhanced electrical conductivity (4955 S cm−1), superior EMI shielding effectiveness (66.28 dB), and an absolute shielding effectiveness (15,029 dB cm2 g−1) at a thickness of 15 μm in the X-band (8.2–12.4 GHz) frequency range that is one of the highest among those of MXenes hybrid composites. [Display omitted] • Lightweight and ultrathin EMI shielding materials were fabricated. • MXene-Galinstan liquid metal hybrid yields superior electrical conductivity. • It exhibited shielding effectiveness of 66.3 dB and an absolute shielding effectiveness of 15,029 dB cm2 g−1. • Such properties attributed to the bridging effect of liquid metal in the hybrid. [ABSTRACT FROM AUTHOR]

[Display omitted] • 2D-MOF is connected to 3D-MOF with coordination bond to form Ni-HHTP@UiO-66NH 2. • 2D-MOF@3D-MOF affords porosity, conductivity, and active interface for sensing. • Ni-HHTP@UiO-66NH 2 shows superior sensitivity and low detection limit toward H 2 S. • A plausible mechanism is proposed from the joint experimental/computational data. Research to develop ideal sensing devices for toxic gases is on the rise, and amongst various materials, metal–organic frameworks (MOFs) have opened up promising vistas as chemiresistive sensors due to their high structural and functional tunability. Here, we report the composites of dimensionally (2D and 3D) and functionally (conductive and porous) different two MOFs in the form of a well-integrated core–shell structure. The hierarchically assembled 2D-MOF@3D-MOF exhibits new interfacial properties that are responsible for synergetically enhanced sensing performances toward toxic H 2 S gas with the lowest recorded limit of detection (1.4 ppb), superior sensitivity (ΔR/R 0 = 3.37), and outstanding selectivity at room temperature in air. The sensing mechanisms are proposed by combinational studies of experiments and calculation, which indicates that multiple changes (e.g., local structural change of the shell MOF, secondary binding sites generation from the core MOF, and free radicals formation) play a critical role in achieving synergetic chemiresistive sensing. [ABSTRACT FROM AUTHOR]

In this work, catalytic Rh 2 O 3 -functionalized WO 3 nanofibers (NFs) were synthesized via an electrospinning route and used as a highly selective acetone-sensing layer for potential diagnosis of diabetes. Catalytic rhodium nanoparticles (Rh NPs) with average diameters of 5.0 ± 0.52 nm, which were synthesized by the polyol process, were dispersed in water with W precursor and poly(vinylpyrrolidone) (PVP) for electrospinning. As-spun Rh NP-loaded W precursor/PVP composite NFs were calcined at 600 °C for 1 h in air atmosphere to achieve Rh 2 O 3 -decorated WO 3 NFs. Microstructure evolution and chemical composition of Rh 2 O 3 -decorated WO 3 NFs as a function of Rh-loading amounts, i.e., 0.01 wt%, 0.05 wt%, 0.10 wt%, and 0.15 wt%, were examined using energy-dispersive X-ray spectroscopy (EDS), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and high-resolution transmission electron microscopy (HRTEM). The mean size (30 nm) of the WO 3 crystallites in Rh 2 O 3 -decorated WO 3 NFs was much smaller than that (60 nm) of the WO 3 crystallites in pristine WO 3 NFs. The Rh 2 O 3 -decorated WO 3 NFs showed outstanding acetone (CH 3 COCH 3 ) sensing response ( R air / R gas = 41.2 to 5 ppm), which was 4.6 times higher than the response ( R air / R gas = 9.0 to 5 ppm) of pristine WO 3 NFs at highly humid atmosphere (95% RH). In addition, superior acetone cross-sensitivity of the Rh 2 O 3 -decorated WO 3 NFs was observed in other interfering gases such as pentane ( n -C 5 H 12 ), ammonia (NH 3 ), toluene (C 6 H 5 CH 3 ), carbon monoxide (CO), and ethanol (C 2 H 5 OH) at 5 ppm. These results are highly promising for the accurate and selective detection of acetone in exhaled breath for potential diagnosis of diabetes. [ABSTRACT FROM AUTHOR]

In this work, highly porous WO 3 nanotubes (NTs) were synthesized by facile layer-by-layer (LbL) self-assembly on polymeric nanofiber (NF) templates followed by calcination. Polymeric NFs using poly(methyl methacrylate) (PMMA) were prepared by electrospinning as sacrificial templates. Then, ionic polymers were coated on PMMA to modify the surface charge of PMMA NFs. Catalyst-loaded WO 3 NTs were synthesized by self-assembly of tungsten precursor and catalytic precursor on the surface of the polymeric PMMA NFs followed by calcination at 500 °C for 1 h. Gas sensing performances were evaluated in highly humid atmosphere (90% RH) using pristine WO 3 NTs, Pt-loaded WO 3 NTs (Pt-WO 3 NTs), and Pd-loaded WO 3 NTs (Pd-WO 3 NTs). Pristine WO 3 NTs exhibited a high NO response ( R gas / R air = 63.59 at 5 ppm) at 350 °C and cross-selectivity toward toluene ( R air / R gas = 1.05 at 5 ppm). On the other hand, Pt-WO 3 NTs and Pd-WO 3 NTs exhibited a high toluene response ( R air / R gas = 2.24 for the Pt-WO 3 NTs and R air / R gas = 2.35 for the Pd-WO 3 NTs at 5 ppm) at 400 °C and a negligible NO response ( R gas / R air = 1.25 for the Pt-WO 3 NTs and R gas / R air = 1.04 for the Pd-WO 3 NTs at 5 ppm) at 400 °C. These results demonstrated that LbL synthesis is a highly promising method for producing hollow semiconductor metal oxide NTs functionalized with various catalysts, which leads to potential application in exhaled breath analysis for asthma and lung cancer diagnosis. [ABSTRACT FROM AUTHOR]

The lack of bifunctional features of perovskite oxide toward the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) significantly limits its use as a cathode catalyst for rechargeable Zn–air batteries (ZABs). Thus far, numerous techniques to disperse additional catalysts on a perovskite host have been suggested to overcome this problem; however, cost-effectiveness and catalyst lifespan remain unsatisfactory. Herein, we present cobalt-based-nanoparticle-decorated Sr 0.95 Nb 0.1 Co 0.7 Fe 0.2 O 3–δ (S0.95NCF) by a simple ex-solution method and use it as a novel air-electrode catalyst. We successfully implemented the socketed nanoparticles with various compositions at different reduction temperatures, achieving notably enhanced activity towards OER and ORR. More importantly, the newly designed catalyst exhibits record-high charge/discharge durability over 500 h (or 1500 consequent cycles) when used as the ZABs cathode. Our findings provide essential guidelines for designing heterostructured electrocatalysts for future energy devices, in which multifunctionality is desirable. [Display omitted] • Ex-solution is applied to Sr 0.95 Nb 0.1 Co 0.7 Fe 0.2 O 3 –δ at various reduction temperatures. • The exsolved metals are elaborately explored depending on ex-solution conditions. • CoFe-nanoalloy ex-solution enhances electrochemical performances for OER and ORR. • The designed catalyst exhibits record-high durability for the Zinc-air batteries. [ABSTRACT FROM AUTHOR]

Antiviral and antibacterial violacein embedded porous nanofiber that can sterilize itself is proposed as an effective solution to prevent aerosol and post-contact transmission of pathogens viruses for safer personal protective equipments. [Display omitted] • Self-sterilizable nanofiber filter with naturally occurring violacein is developed. • Remarkable biocidal activities against infectious viruses and bacteria are achieved. • Viricidal efficacy for influenza and human coronavirus is studied by TCID 50 analysis. • Porous nanofiber matrix immobile pathogens and prevents aerosol transmission. • Violacein endows nanofibers with UV shielding property to help protect skin. Most respiratory masks are made of fabrics, which only capture the infectious virus carriers into the matrix. However, these contagious viruses stay active for a long duration (∼7 days) within the fabric matrix possibly inducing post-contact transmissions. Moreover, conventional masks are vulnerable to bacterial growth with prolonged exposure to exhaled breaths. Herein, we combined violacein, a naturally-occurring antimicrobial agent, with porous nanofiber membranes to develop a series of functional filters that autonomously sterilizes viruses and bacteria. The violacein-embedded membrane inactivates viruses within 4 h (99.532 % reduction for influenza and 99.999 % for human coronavirus) and bacteria within 2 h (75.5 % reduction). Besides, its nanofiber structure physically filters out the nanoscale (<0.8 μm) and micron-scale (0.8 μm − 3 μm) particulates, providing high filtration efficiencies (99.7 % and 100 % for PM 1.0 and PM 10, respectively) with long-term stability (for 25 days). In addition, violacein provides additional UV-resistant property, which protects the skin from sunlight. The violacein-embedded membrane not only proved the sterile efficacy of microbe extracted pigments for biomedical products but also provided insights to advance the personal protective equipment (PPE) to fight against contagious pathogens. [ABSTRACT FROM AUTHOR]

[Display omitted] • A simple but powerful solution to overcome the chronic bottleneck of the nanocatalyst delivery on oxide support: the carbothermal shock driven nanocatalyst formation on carbon nanofibers (CNFs) with small sizes and fine distribution can be delivered to oxide structures of choice while retaining high uniformity. • Fabrication of catalyst delivered porous oxide structures: the asymmetric sputtering of oxide on CNFs can induce the formation of openly porous hemi-tubular structures with tunable porosity and thickness. A simple subsequent calcination results in the transfer of catalysts from the CNF template to the porous oxide structures. • Superior hydrogen sulfide sensing properties: Uniform distribution of Pt nanoparticles on SnO 2 hemitubes showed superior H 2 S sensing performances (Response Rair/Rgas > 1500 at 5 ppm H 2 S) compared to state-of-the-art H 2 S sensors. To achieve powerful gas sensors oxide semiconductor chemiresistors, the uniform functionalization of nanocatalysts on the desired metal oxides is considered as a key strategy. However, still, it is challenging to achieve the nanocatalysts decoration on desired oxides without deterioration of target materials. In this study, thermal-shock (rapid joule-heating method) was applied to uniformly decorate Pt nanoparticles (NPs) on the surface of carbon nanofibers (CNFs) to achieve the uniform distribution of Pt NPs on one-dimensional structures. And then, SnO 2 was physically deposited on the Pt NPs loaded CNFs and continuous heat-treatment was conducted to transfer the Pt NPs to desired SnO 2 porous hemitubes. Thanks to the well-distributed Pt NPs on porous SnO 2 hollow structures, the Pt laoded SnO 2 hemitubes showed an exceptional sensitivity (R air /R gas = 1500 at 5 ppm) in H 2 S. Also, it showed high selectivity for H 2 S and high stability even under continuous gas exposure, confirming its potential as an effective H 2 S sensor. [ABSTRACT FROM AUTHOR]

Abstract: Chemoresistive H2S sensors using various oxide nanoparticles were prepared and heat-treated at 600°C in an effort to define halitosis in human breath. WO3, ZnO, and SnO2 were tested as sensing materials, among which WO3 showed the highest stability to H2S. XPS analysis showed a metal sulfate peak on the surface of ZnO and SnO2, which causes a recovery problem after 2ppm H2S exposure. On the contrary, the WO3 sensor showed a stable signal in long-term operation in the presence of H2S gas. WO3 gas sensors decorated with various catalytic metals were fabricated to investigate their sensing properties in the 0.2–5ppm H2S range with 80% relative humidity (RH). A 0.03wt% Au-doped WO3 sensor exhibited excellent H2S sensitivity (R air/R gas =12.40at 2ppm) toward H2S, whereas pure WO3 showed a sensitivity of 4.85 with negligible interference from the volatile organic compounds (VOCs). [Copyright &y& Elsevier]

Abstract: An ultraselective and ultrasensitive trimethylamine (TMA) sensor was achieved using MoO3 nanoplates-prepared by ultrasonic spray pyrolysis followed by a heat treatment at 450°C. The small and thin MoO3 nanoplates with gas-accessible structures showed an unusually high response to 5ppm TMA (ratio of resistance to air and gas=373.74) at 300°C with detection limit as low as 45ppb. Moreover, the ratios of the cross-responses to interfering gases (i.e., 5ppm C2H5OH, CO, CH4, C3H8, H2, and NO2) to the response to 5ppm TMA were extremely low (0.008–0.016). The source of the ultraselective and highly sensitive detection of TMA with negligible interference from other gases is discussed with respect to the acid/base properties, size, and morphology of the MoO3 sensing materials. [Copyright &y& Elsevier]

In this work, we report a remarkably improved toluene response and superior cross-sensitivity against H2S molecules by combining Pd catalysts and highly porous WO3 nanofibers (NFs). We functionalized Pd catalysts inside and/or outside of WO3 NFs synthesized by electrospinning, which is a facile and versatile process for producing webs of metal oxide NFs. Pd-embedded WO3 NFs were obtained by the electrospinning of a Pd and W composite precursor/poly(methyl methacrylate) (PMMA) solution followed by calcination at 700°C. Pd nanoparticles (NPs) (6–10nm) synthesized by a polyol method were decorated on the WO3 NFs (Pd-NPs/WO3 NFs) by the attachment of the Pd NPs on as-prepared WO3 NFs. The gas sensing characteristics of pure WO3, Pd-embedded WO3, Pd-NPs/WO3, and Pd-NPs/Pd-embedded WO3 NFs were tested using H2S and toluene gases in a highly humid atmosphere (RH 90%), which is similar to human exhaled breath. The results showed that the Pd-NPs/Pd-embedded WO3 NFs whose inner and outer layers were decorated by Pd catalysts, exhibited a high toluene response (R air/R gas =5.5 at 1ppm) and remarkable selectivity against H2S (R air/R gas =1.36 at 1ppm) at 350°C, whereas pristine WO3 NFs showed superior H2S response (R air/R gas =11.1 at 1ppm) along with a negligible response toward toluene (R air/R gas =1.27 at 1ppm). The highly porous WO3 NFs decorated with Pd catalysts, exhibited potential feasibility, i.e., a low limit of detection (LOD) of 20ppb (R air/R gas =1.32) at 350°C, for application in VOCs sensors, particularly for diagnoses of lung cancer. [ABSTRACT FROM AUTHOR]

Abstract: Polyimide (PI) nanofibers with an average diameter of 300 nm, possessing superior electrolyte wettability and thermal stability, are synthesized by electrospinning a poly(amic acid) (PAA) solution followed by an imidization process. The large pore volume of the PI nanofiber mat can facilitate faster Li+-ion transport and greater rate capability, but it also cause an irreversible increase in cell impedance during long term cycling. To overcome these problems, thin Al2O3 over-layers are coated on both sides of a PI separator via a dip-coating process. The Al2O3-coated PI separators exhibit enhanced capacity, cyclability (95.53% retention after 200 cycles at 1 C), and rate capabilities (78.91% at 10 C) compared to the bare PI separator (68.65% at 10 C) and a commercial polypropylene separator (18.25% at 10 C) with a limited increase of cell impedance. [Copyright &y& Elsevier]

We report on facile synthesis of SnO2 nanofibers (NFs) functionalized by Pt nanoparticles (NPs) with various loading contents (0.05–0.4wt%) and their gas response toward H2, NO2, NH3, CO, and SO2 gases as a function of the operation temperature (100–450°C) and gas concentration (0.125–2.5ppm). Mesoporous SnO2 NFs with large surface-to-volume ratio, which facilitates sensitive gas response, were synthesized by electrospinning followed by subsequent calcination at 500°C for 2h. Colloidal Pt NPs synthesized by simple polyol method were immobilized on SnO2 NFs as a catalytic sensitizer to H2 oxidation. The gas sensing properties and response kinetics were significantly affected by the Pt NPs and the operation temperature. It was found that 0.1wt% Pt-loaded SnO2 sensor showed the highest H2 response (I gas/I air =16.6 at 2.5ppm) at 300°C. A remarkably high NO2 response (I air/I gas =57.0 at 2.5ppm) was achieved in the case of pristine SnO2 sensor at 150°C. This work demonstrates that sensitive and selective detection of H2 and NO2 gases with negligible cross-response to interfering gases such as NH3, CO, and SO2 can be obtained by decoration with Pt NPs on metal oxide NFs in conjunction with manipulation of the operation temperature. [ABSTRACT FROM AUTHOR]

Abstract: Cerebral ischemia leads to brain injury via a complex series of pathophysiological events, and therefore, multi-drug treatments or multi-targeting drug treatments provide attractive options with respect to limiting brain damage. Previously, we reported that a novel multi-functional compound oxopropanoyloxy benzoic acid (OBA-09, a simple ester of pyruvate and salicylic acid) affords robust neuroprotective effects in the postischemic rat brain. OBA-09 exhibited anti-oxidative effects that appeared to be executed by OBA-09 and by the salicylic acid afforded by hydrolysis. Here, we report the anti-inflammatory effects of OBA-09. Microglial activation observed at 2 days post-middle cerebral artery occlusion (MCAO, 90min) and at 1 day after a LPS injection (0.5mg/kg, intravenously) in the brains of Sprague-Dawley rats were markedly suppressed by the administration of OBA-09 (10mg/kg). Inductions of proinflammatory markers (TNF-α, IL-1β, iNOS, and COX-2) were also suppressed by OBA-09 in both the LPS and MCAO models. Moreover, the anti-inflammatory effect of OBA-09 was accompanied by the suppression of infarct formation in the postischemic brain, but appeared to be independent of neuroprotection in LPS-treated rats. The inductions of proinflammatory markers were also inhibited by OBA-09 in LPS-treated BV2 cells (a microglia cell line) and in LPS-treated-primary neutrophils, possibly due to the suppression of NF-κB activity. Interestingly, the anti-inflammatory effect of OBA-09 was greater than that of equivalent co-treatment with pyruvate and salicylic acid. Together these results indicate that OBA-09 is a potent multi-modal neuroprotectant in the postischemic brain, and that its anti-inflammatory effect contributes to its neuroprotective function. [Copyright &y& Elsevier]

Abstract: The response characteristics of amorphous-InGaZnO4 (a-IGZO4) thin films toward reducing/oxidizing gases (H2/NO2), at sensor operating temperatures, are reported for the first time. The lack of grain boundaries eliminates a major source of electrical, microstructural and chemical inhomogeneities associated with polycrystalline semiconducting metal oxides (SMOs), rendering a-IGZO4 a highly promising model sensor system. Gas sensor tests were carried out in the temperature range of 200–400°C by monitoring changes in DC resistance during cyclic exposure to trace concentrations (between 1.25 and 50ppm) of H2 or NO2 in dry air. The response (S) to H2 was found to go through a temperature maximum (e.g. S ∼0.7 at 350°C for pH2 =12.5ppm) that value being a function of pH2. The response to NO2, on the other hand, decreased with increasing temperatures with the highest recorded values at 200°C (e.g. S ∼33 at 200°C for pNO2 =5ppm). The response followed an approximate power law dependence on gas partial pressure (p), S = Ap β , with β taking on values of ∼0.5–1.0 as temperature increased from 200 to 400°C. Response times were found to range from 10s to greater than 1000s as temperature decreased. The hysteretic behavior exhibited by a-IGZO films between 150 and 400°C, under temperature sweep conditions, is attributed to kinetically limited adsorption/desorption and reaction rates. [Copyright &y& Elsevier]

Abstract: Ethyl pyruvate (EP), a simple ester of pyruvic acid, has been shown to act as an anti-inflammatory molecule under various pathological conditions, such as, during cerebral ischemia and sepsis in animal models. Here, the authors investigated the novel molecular mechanism underlying the anti-oxidative effect of EP in primary astrocyte cultures, particularly with respect to nuclear factor E2-related factor 2 (Nrf2) activation and hemeoxygenase 1 (HO-1) induction. EP was found to induce Nrf2 translocation and the inductions of various genes downstream of Nrf2 and these resulted in the amelioration of the oxidative damage of H2O2. Furthermore, EP dose-dependently suppressed H2O2-induced astrocyte cell death (12h preincubation with 5mM EP increased cell survival after 1h exposure to 100μM H2O2 from 32.6±0.7% to 63±1.8%). HO-1 was markedly induced (4.9-fold) in EP-treated primary astrocyte cultures and Nrf2 was found to translocate from the cytosol to the nucleus and bind to the antioxidant response element (ARE) located on HO-1 promoter after EP treatment. siRNA-mediated HO-1 or Nrf2 knockdown and zinc protoporphyrin (ZnPP)-mediated inhibition of HO-1 activity showed that Nrf2 activation and HO-1 induction were responsible for the observed cytoprotective effect of EP, which was found to involve the ERK and Akt signaling pathways. Furthermore, EP-conditioned astrocyte culture media was found to have neuroprotective effects on primary neuronal cultures exposed to oxidative or excitotoxic stress, and this seemed to be mediated by glial cell line-derived neurotrophic factor (GDNF) and glutathione (GSH), which accumulated in EP-treated astrocyte culture media. Interestingly, we also found that in addition to HO-1, EP-induced Nrf2 activation increased the expressions of various anti-oxidant genes, including GST, NQO1, and GCLM. The study shows that EP-mediated Nrf2 activation and HO-1 induction in astrocytes act via autocrine and paracrine mechanisms to confer protective effects. [Copyright &y& Elsevier]

Abstract: High mobility group box 1 (HMGB1) is an endogenous danger signal molecule. In a previous report, we showed that HMGB1 is massively released during NMDA-induced acute damaging process in the postischemic brain and triggers inflammatory processes, like microglial activation. siRNA-mediated HMGB1 knockdown markedly reduced infarct volumes, confirming the crucial role played by HMGB1 in the postischemic brain. In the present study, we showed neuroprotective effects of glycyrrhizin (GL) in the postischemic rat brain after middle cerebral artery occlusion (MCAO). GL, a triterpene present in the roots and rhizomes of licorice, Glycyrrhiza glabra, has been shown to have anti-inflammatory and anti-viral effects. It has been reported that GL binds directly to HMGB1, and inhibits its chemoattractant and mitogenic activities. The administration of GL (10mg/kg) intravenously at 3 or 6h after MCAO reduced infarct volumes to 12.9±4.2% and 46.2±9.9%, respectively, of untreated control. This neuroprotective effect was accompanied by improvements in motor impairment and neurological deficits and suppressions of microglia activation and proinflammatory cytokine induction. Interestingly, GL almost completely blocked HMGB1 secretion in the postischemic brain and in lipopolysaccharide (LPS)-treated microglia cells. Furthermore, HMGB1 phosphorylation, which is the initial step for HMGB1 secretion, and the interaction between HMGB1 and protein kinase C (PKC) or calcium/calmodulin-dependent protein kinase IV (CaMKIV) were suppressed dose-dependently by GL. Here, we hypothesized that the blockage for the putative phosphorylation sites in HMGB1 by GL might be attributed to this suppression. In addition to the anti-inflammatory effects, we found that GL has anti-excitotoxic and anti-oxidative effects in neurons. Together these results indicate that GL has neuroprotective efficacy in the postischemic brain via its anti-inflammatory, anti-excitotoxic, and anti-oxidative effects and in particular, it exerts anti-inflammatory effect, at least in part, by inhibiting HMGB1 secretion. [Copyright &y& Elsevier]

Abstract: SnO2 hollow nanofibers (HNFs) with diameters of 300–500nm were fabricated via electrospinning of templating nanofibers and RF-sputtering of SnO2 thin overlayers (15–20nm thick and comparable grain size) followed by heat-treatment at 450°C. Gas sensors using these HNFs exhibited n-type gas sensing characteristics and an enhanced gas response to 2ppm NO2 (R gas /R air =81.4) as compared to that (R gas /R air =19.9) of planar SnO2 thin films. The enhanced response to NO2 is attributed to the greater accessible active area and the greater space charge modulation depth associated with the hollow thin walled structures. [Copyright &y& Elsevier]

Abstract: The activation of p38 mitogen-activated protein kinases (MAPKs) has been implicated in many cellular processes, such as, inflammation, cell death, and survival. In mammals, four distinct genes encode the four known members of p38 MAPKs, p38α, p38β, p38γ, and p38δ. Despite the fact that p38α and p38β MAPKs share over 75% homology sequences, they have distinct, perhaps even opposite roles under stress conditions. In our previous report, we showed that p38β MAPK is induced in activated astrocytes in the penumbra of the postischemic brain, wherein it was co-localized with αB-crystallin and MAPKAPK-2. To investigate the functional significance of p38β MAPK in astrocytes, a C6 astroglioma cell line stably over-expressing p38β MAPK was generated. In these cells, hydrogen peroxide-induced apoptosis was reduced to 44.3% of that obtained from normal C6 cells. Interestingly, we found that expression of a small heat shock protein, αB-crystallin, was significantly increased in these cells, but that the expressions of HSP27 and HSP70 were not. Repression of αB-crystallin expression by αB-crystallin siRNA transfection suppressed the protective effect and recovered caspase 3 activity, indicating that αB-crystallin induction plays a crucial role in the protection against H2O2-induced apoptosis observed in p38β-overexpressing C6 astroglioma cells. We found that the binding between αB-crystallin and partially processed caspase-3 (a p24 intermediate) was significantly increased in p38β-overexpressing cells, which might result in suppression of caspase 3 activity in these cells. These results indicate that p38β confers protection against H2O2-induced astrocytes apoptosis by inducing a small heat shock protein, αB-crystallin, which inhibits caspase-3 activation. [Copyright &y& Elsevier]

Abstract: This work presents a new route to enhance the sensitivity of nanocrystalline TiO2 fibers based gas sensors. Pure and Pd-doped TiO2 nanofiber mats were synthesized by electrospinning and subsequent calcination. Highly porous fibrillar morphology was observed in the resultant nanocrystalline TiO2 fibers. In addition to anatase TiO2 crystallites, tiny (∼2nm) PdO crystallites were observed in the Pd-doped TiO2 fibers. The sensors using Pd-doped TiO2 fibers showed promising gas sensing characteristics, such as low operation temperature (180°C) and sufficient gas response (R/R o =38 to 2.1ppm NO2). The techniques outlined here offer new means for preparing novel metal-oxide nanofibers with catalytic dopants. [ABSTRACT FROM AUTHOR]

Abstract: To enhance the sensitivity of a metal oxide-based gas sensor, we introduce a novel electrical method that relies jointly on the use of impedance and an applied DC bias. We used polycrystalline ZnO–NiO composite thin films prepared by pulsed layer deposition as CO gas sensor material. The applied DC bias lowers the interface barrier between oxide grains and thereby enhances the sensitivity. Our approach enhances the sensitivity to CO gas by approximately 200% more than a conventional DC method. The enhancement effect is more pronounced when the CO concentration is lowered. This method offers an efficient characterization tool for modulating the sensitivity of gas sensors using semiconducting metal oxides. [Copyright &y& Elsevier]

Abstract: We report on high mobility ZnO thin film transistors (TFTs) (<5V), utilizing a room temperature grown MgO–Bi1.5Zn1.0Nb1.5O7 (BZN) composite gate insulator on a glass substrate. 30mol% MgO added BZN composite gate insulators exhibited greatly enhanced leakage current characteristics (~<2×10−8 A/cm2 at 0.3MV/cm) due to the high breakdown strength of MgO, while retaining an appropriate high-k dielectric constant of 32. The ZnO-TFTs with MgO–BZN composite gate insulators showed a high field-effect mobility of 37.2cm2/Vs, a reasonable on–off ratio of 1.54×105, a subthreshold swing of 460mV/dec, and a low threshold voltage of 1.7V. [Copyright &y& Elsevier]

• The non-noble metals are introduced on graphene-based fiber as a sensitizer for the high-performance chemiresistor. • Metal oxides on graphene fibers naturally are converted into metals at a relatively low temperature annealing (under 700 °C) due to catalytic effect of graphene. • The graphene fiber acts as a flexible conductive support as well as a catalyst for the deoxidation of metal oxide. • The metal/metal oxide/graphene fibers exhibited a 16 times higher response to NO 2 gas and recovery than metal oxide/graphene fiber without metal. • The proposed strategy opens a new avenue for the realization of high-performance devices, such as chemical catalysts, photoactive devices. [Display omitted] Noble metal/metal-oxide-based hybrid gas sensors exhibit a low operating temperature, remarkable sensitivity, and fast recovery. As additives, noble metals induce a catalytic sensitization effect, which promotes charge transfer from the metal oxide to the analyte molecules, the so-called spillover mechanism. This suggests that metal catalysts can improve gas sensing performance. Herein, for the first time, non-noble metals are introduced on hybrid metal oxide/graphene fibers as sensitizers to fabricate high-performance chemiresistive sensors. The formation of metal components can be effectively controlled by annealing the metal oxide on graphene. Remarkably, compared with the corresponding metal oxide/graphene fiber sensors without metal components, the metal/metal oxide/graphene fiber sensors exhibit over a 16-fold higher response to NO 2 gas as well as effective recovery characteristics. Specifically, the Cu/Cu 2 O/graphene and Ni/NiO/graphene fiber sensors operating at 150 °C exhibit sensitivities of 18.90 % and 0.82 %, respectively, for 5 ppm NO 2 gas. The proposed strategy to achieve flexible graphene fiber chemiresistors by decorating them with non-noble metal and metal oxide nanoparticles opens a new avenue for realizing high-performance devices, such as photovoltaic devices, photocatalysts, and chemical catalysts. [ABSTRACT FROM AUTHOR]

• Porosity control of nanofibers: The high porosity of the metal oxide nanofibers is the key to achieving the dual sensitization owing to their high gas permeability and numerous active sites. Both saponin and water-ethanol co-solvent play critical roles in modifying morphology of nanofibers into elliptical nanofibers during electrospinning. Additionally, saponin forms numerous pores in the nanofibers when being burnt out during calcination. These porous, elliptical nanofibers possess a larger surface area and porosity.Saponin and water-ethanol co-solvent enabled porous, elliptical nanofibers to emerge. • Bifunctional Ga doping: Ga dopants enhanced sensing performance via conductivity improvement and grain growth inhibition. • Functionalization of Pt catalysts : Spill-over effects and chemical sensitization of remarkably improved C 2 H 2 sensitivity. Herein, we demonstrate a sensitization strategy via solid-solution doping and catalytic metal nanoparticles (NPs) onto porous metal oxide nanofibers (NFs) for superior acetylene (C 2 H 2) sensing capabilities. The introduction of dopants and catalysts not only increases the inherent reactivity of metal oxides, but also induces the spillover of C 2 H 2 onto metal oxides, significantly improving the sensing properties. We elucidate that the high porosity of the metal oxide NFs, prepared by electrospinning and utilizing saponin as a sacrificial template, is the key to achieving high gas permeability and numerous active sites. Consequently, Ga-doped ZnO porous NFs functionalized with Pt catalysts exhibited the highest C 2 H 2 sensing responses among the current state-of-the-art C 2 H 2 sensors (R a /R g = 26.2 at 400 °C) with a fast response time (10.2 s), at a particularly low concentration of 5 ppm. Moreover, these NFs showed excellent selectivity against the interfering gas (H 2 , C 7 H 8 , CO, CH 4 , C 8 H 10 , CH 3 COCH 3 , HCHO and C 2 H 5 OH) and outstanding stability up to 20 sensing cycles to 0.4 ppm of C 2 H 2. These results provide an efficient strategy to tailor composites of metal oxide nanostructures, dopants, and catalysts for highly sensitive gas sensors. [ABSTRACT FROM AUTHOR]

• Synthesis of CA-CNF by insulating block electrospinning & carbonization. • Formation of cross-aligned network even after heat treatment. • Faster reaction kinetics and regular electron pathway of CA-CNF. • High-rate cyclability of CA-CNF (259.4 mAh g−1 at 3000 mA g−1). The conventional use of metallic current collector in an electrochemical cell results in decreased loading of active materials and hence limited capacity in consideration of all the inactive current collector components. In response to this trend, a number of conductive, free-standing materials have been proposed as electrodes, which would act as both current collector and active materials. Here, in this study, we have firstly developed the cross-aligned carbon nanofiber (CA-CNF) for efficient Li storage, especially at high current densities. Using the insulating block electrospinning, the nanofibers can be aligned in a certain direction, where it is viable to fabricate cross-aligned nanofibers in a cost-effective and scalable manner. Attributed to faster kinetics and regular electron pathway arising from CA-CNF, it exhibits an excellent high-rate cyclability (259.4 mAh g−1 at a current density of 3000 mA g−1). This work builds up a milestone in suggesting a cross-aligned carbon nanofibrous network as efficient Li storage, which can also be applied to various electrode materials embedded cross-aligned conductive composite materials. [Display omitted] [ABSTRACT FROM AUTHOR]

[Display omitted] • High P-doped (9.24 at%) thick carbon electrodes (CW-P) by phytic acid treatment. • SSC exhibits high capacitance of 4.7F cm−2/206.5F g−1 at 1.0 mA cm−2. • Excellent capacitance retention of 90.5% after 20 000 cycles (@20 mA cm−2). • High energy density up to 0.94 mW h cm−2 (41.2 Wh kg−1). • High power density up to 0.6 mW cm−2 (26.3 W kg−1). Keeping outstanding electrochemical performance under high mass loading is critical to develop functional thick electrodes. Here, we report a high phosphorus-doped wood-derived carbon thick electrode for supercapacitor via phytic acid treatment, which can form hydrogen bonds with cellulose molecules in the wood. The content of phosphorus reaches up to 9.24 at% in carbonized wood with P-doping (CW-P-9.24), higher than most previously reported P-doped carbonaceous materials. CW-P-9.24 electrode (800 μm, 17.17 mg cm−2) exhibits greatly improved electrochemical performance, especially in energy density and cyclic stability. Significantly, the symmetrical supercapacitor device exhibits high areal and specific capacitance of 4.7 F cm−2 and 206.5 F g−1 at 1.0 mA cm−2 with prominent retention of 90.5% through the long-term cycling at 20 mA cm−2 for 20,000 cycles, and 0.94 mW h cm−2 (41.2 Wh kg−1) at power density of 0.6 mW cm−2 (26.3 W kg−1), and possesses excellent volumetric capacitance and energy density of 29.3 F cm−3 and 5.8 Wh cm−3, respectively. The outstanding performance can be attributed to the excellent hierarchical structure, low tortuosity, and high phosphorus doping with fast accessible channels at high current density. The extraordinary performance of CW-P has been elucidated by density functional theory calculations, which confirm the enhanced activity by P-doping. These results demonstrate that the CW-P electrode is promising for practical application in energy storage devices and encourage more investigations for thick electrode. [ABSTRACT FROM AUTHOR]

• Novel top-down synthesis of CNS from aronia fruit powder by carbonization. • Temperature-independent synthesis of CNS. • Gas atmosphere-independent synthesis of CNS. • CNS exhibits high-rate cyclability for Li+ and K+ ion storage. • Structural integrity was well maintained even after cycling for Li+ and K+. Carbon nanosheets (CNSs) have been used in various applications, ranging from energy storage to drug delivery. CNSs are conventionally synthesized by chemical vapor deposition, but their high cost and non-scalability prompted the development of alternative synthesis routes. More scalable methods such as the sol-gel process still suffer from its complicated synthetic steps with delicate conditions. Here, we demonstrate for the first time a unique top-down synthesis of CNSs from aronia fruit powder, which is simple, scalable, and cost-effective. Aronia-derived CNS can be fabricated at various heating temperatures (500, 700, and 900 °C) and under different atmospheres (N 2 /H 2 and NH 3), which can easily tune the overall physicochemical properties of the CNS. We evaluated the electrochemical performance of the CNS for potential applications in Li- and K-ion batteries, in which the CNS showed stable electrochemical performance even at a high current density (1000 mA g−1). Because of the high-throughput nature of this synthetic approach, the aronia-derived CNSs could be very useful in developing novel applications at an industrial scale. [Display omitted] [ABSTRACT FROM AUTHOR]

The low response and sluggish reaction kinetics of graphene-based gas sensors remain as obstacles for practical applications as wearable chemical sensors. To overcome these limitations, we demonstrate a heterogeneous sensitization of nanocatalysts using Pt and ZnO nanoparticles (NPs) on porous reduced graphene oxides (Pt_ZnO/PRGO) driven by a metal-organic framework (MOF)-templated synthesis and subsequent pyrolysis. The pyrolysis of zeolitic imidazolate framework-8 layers grown on graphene oxide leads to the creation of porous carbon frameworks decorated with catalytic Pt and ZnO NPs, which possess increased reaction sites for the target gas. In addition, we investigated the effect of pyrolysis conditions to control the size of ZnO NPs with a 10 nm scale for enhanced catalytic sensitization. As a result, Pt_ZnO/PRGO exhibited improved NO 2 sensing properties with regard to response (43.28 % to 5 ppm), selectivity, and detection limit (0.1 ppm), as well as having reversible reaction kinetics. Potential applications of MOF-derived Pt_ZnO/PRGO in wearable chemical sensors was demonstrated, in which the material exhibited excellent mechanical stability and reliable response after 450 bending cycles. [ABSTRACT FROM AUTHOR]

• Synthesis of MFC from low-grade gum wastes. • The synthesized MFC possesses high tap density (1.4–1.7 g cm−3). • High tap density leads to outstanding volumetric capacity at 3.0 A g−1. • MFC also exhibits ultra-stable high-rate cyclability (0.001881% decrease per cycle). • Structural integrity was well maintained even after cycling. Among various natural wastes, gum wastes pose major issues, as they are unusable and hard to be disposed due to their acidic and sticky nature. Herein, a rational synthetic strategy is employed to transform various kinds of gum wastes into micron-sized carbon, which also exhibit high tap density (1.4–1.7 g cm−3) desirable for practical application in lithium-ion batteries (LIBs). Gum karaya (GK) micron-size functional carbon (GKMFC) exhibits the most outstanding electrochemical performance, with a volumetric capacity of 175.4 mAh cm−3 at a current density of 3000 mA g−1 for 5000 cycles, and possesses ultra-stable high-rate cyclability (a capacity decay of only 0.001881% per cycle). Additional electrochemical analyses reveal that GKMFC exhibits stable structural integrity as well as minimal cell resistance even after cycling, showing its practical application as viable electrode for LIBs. This work sheds light on utilizing high tap density carbon from gum wastes for LIBs, which can also be applicable to other natural wastes and carbon. Image, graphical abstract [ABSTRACT FROM AUTHOR]

• Electrospinning of plant- and microbial-based carbohydrate gums is discussed. • Electrospinning parameters with respect to gums are illustrated. • Applications of carbohydrate gum-derived electrospun fibers are exemplified. Electrospinning has garnered significant attention in view of its many advantages such as feasibility for various polymers, scalability required for mass production, and ease of processing. Extensive studies have been devoted to the use of electrospinning to fabricate various electrospun nanofibers derived from carbohydrate gum polymers in combination with synthetic polymers and/or additives of inorganic or organic materials with gums. In view of the versatility and the widespread choice of precursors that can be deployed for electrospinning, various gums from both, the plants and microbial-based gum carbohydrates are holistically and/or partially included in the electrospinning solution for the preparation of functional composite nanofibers. Moreover, our strategy encompasses a combination of natural gums with other polymers/inorganic or nanoparticles to ensue distinct properties. This early established milestone in functional carbohydrate gum polymer-based composite nanofibers may be deployed by specialized researchers in the field of nanoscience and technology, and especially for exploiting electrospinning of natural gums composites for diverse applications. [ABSTRACT FROM AUTHOR]

• To control the porosity, the e-spraying and PS beads templating route are combined, resulting in highly porous structure. • Pt functionalized PH-SnO 2 spheres exhibited high response (R air /R gas = 44.83) toward 5 ppm of acetone. • Pt-PH-SnO 2 spheres exhibited exceptional selectivity toward acetone against interfering molecules. Tailoring of semiconducting metal oxides (SMOs) nanostructures with high porosity is of importance for enhanced gas sensing performance. Hierarchically-assembled SMOs possess high surface area but often suffer from low porosity. Here, bimodal pore-loaded hierarchical SnO 2 (PH-SnO 2) spheres were successfully synthesized via electrostatic spraying method (e-spraying) combined with colloidal templating route using polystyrene beads. The resulting porous PH-SnO 2 spheres were used as sensing layers for detection of acetone, which exhibited about 20 % enhanced response compared with hierarchical SnO 2 (H-SnO 2) spheres without pores. In addition, e-spraying is a fascinating technique for uniform catalytic functionalization through a simple dispersion of catalytic nanoparticle (NPs) in the e-spraying solution to improve the sensing performance. As a result, the Pt-functionalized PH-SnO 2 (Pt-PH-SnO 2) spheres showed dramatically improved acetone detection capability with a response (R air /R gas) of 44.83 at 5 ppm as compared to PH-SnO 2 spheres (R air /R gas = 6.61) as well as superior selectivity. In this work, the unique combination of e-spraying and PS templating route paves the way for robust and facile synthetic method for bimodal pore loaded 3D hierarchical SMOs, and demonstrates the feasibility for application in exhaled breath sensors. [ABSTRACT FROM AUTHOR]